JLab GO AIR POP User Manual Getting Started
GO AIR POP EARBUDS
We love that you are rocking JLab! We take pride in our products and fully stand behind them.
All warranty claims are subject to JLab authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.
Reach out to us at firstname.lastname@example.org or visit jlab.com/contact
Product updates | How-to tips | FAQs & more
Remove tab and close door
Red light on case indicates charge.
Remove earbuds from case.
One earbud will blink blue/white indicating ready to pair to your device.
Select “JLab GO Air Pop” in your device's Bluetooth settings to connect.
Voice prompt “You’re connected” followed by blinking white lights will indicate you are connected.
ADDING NEW / ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth from new device.
Take earbuds out of the case. Earbuds will automatically enter Bluetooth Pairing.
Select “JLab GO Air Pop” in device settings to connect.
VOLUME DOWN: Single tap
SIRI (iOS) or “OK GOOGLE” (ANDROID): Double tap
TRACK BACK: Press & hold 1+ sec
VOLUME UP: Single tap
PLAY / PAUSE: Double tap
TRACK FORWARD: Press & hold 1+ sec
SHARED CONTROLS (Both Left and Right Earphones)
ANSWER CALL: Single tap
HANGUP: Double tap
REJECT INCOMING CALLS: Press & hold 1+ sec
EQ CHANGE: Triple tap
“Hello”: Power ON
“Ready to Pair”: GO Air Pop is ready to pair to Bluetooth device
“Bluetooth Connected”: Earbud is connected to device
“Battery Full”: 100-75%
“Battery Medium”: 75-25%
“Low Battery”: Less than 25% (When power decreases to 10%, “Low Battery” will play one time)
“Goodbye”: Power OFF
CUSTOM EQ SOUND MODES
Tap either the right or left earbud 3 times for different EQ settings (GO Air Pop will cycle 3 EQ settings).
JLab C3™ signature sound with amplified bass and vocals
Even sound with no additional enhancements
Amplified bass and sub-bass
Earbuds will power off when placed in the case and start charging the earbuds.
Earbuds will auto power on and connect to your device when removed.
Connect the GO Air Pop into a computer or USB 5V 1A (or less) output device.
Charging: Blinks Blue
Fully Charged: Solid Blue
Try all ear tips for best fit and proper seal.
Place the earbud in the ear canal and slightly rotate to adjust for best fit.
The left or right earbud can be used independently for music and phone calls. Simply choose one and take out of the case to connect.
Only ONE Bluetooth device can be connected at a time. Turn off Bluetooth on unwanted devices and turn on Bluetooth on chosen device to connect.
Fully dry off earbuds before putting in the charging case to avoid any damage to the case. The earbuds are sweat/water resistant but the case is not.
Fully dry off the earbuds before putting in the charging case to avoid any damage to the case.
The earbuds are sweat/water resistant but the case is not.
Connection failure or earbuds disconnected from each other (Manual Reset)
Keep the earbuds in the charging case and forget “JLab GO Air Pop” from your Bluetooth device settings.
Quick tap 7x on one earbud in charging case. Earbud blinks blue 4 times.
Quick tap 7x on other earbud in charging case. Earbud blinks blue 4 times.
Take both earbuds out of the charging case. One earbud will be solid white and other will blink blue/white indicating ready to pair to your device.
Instructional videos at: JLAB.COM/MANUALS
Avoid extreme heat, cold, and humidity.
Avoid dropping or crushing the earbuds.
Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
If you experience regular discomfort while using this product, discontinue use and consult your physician.
We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
Shop products | Product alerts | Burn-in your headphones
JLab Store + Burn-in Tool
Was this information helpful?