Sony SLV-SF99EN manual

Sony Support

Documents

Sony SLV-SF99EN User Manual [PDF]

Pages: 116 | Size: 1.89 MB

Safety
Installing
Caution
Compatible colour systems
Table of contents
- * ShowView is a registered trademark of Gemstar Development Corporation. ShowView system is manuf...
  - Getting Started
Step 1
- Unpacking
Step 2
- Setting up the remote commander
  - Inserting the batteries
  - Using the remote commander
- Step 2 : Setting up the remote commander (continued)
  - TV control buttons
    - Notes
      - • In normal use, the batteries should last about three to six months.
      - • If you do not use the remote commander for an extended period of time, remove the batteries to ...
      - • Do not use a new battery with an old one together.
      - • Do not use different types of batteries together.
      - • Some buttons may not work with certain Sony TVs.
  - Setting the COMMAND MODE switch
- Step 2 : Setting up the remote commander (continued)
  - Controlling other TVs with the remote commander
    - 1
    - 2
    - * These buttons may not work with all TVs.
    - Tip
      - • When you set your TV’s code number correctly while the TV is turned on, the TV turns off automa...
    - Code numbers of controllable TVs
      - *1 Press WIDE to switch the wide picture modes.
      - *2 Press WIDE, then press 2 +/– to select the wide picture mode you want.
      - *3 Press WIDE. The menu appears on the TV screen.Then, press CURSOR M/m/</, to select the wide pi...
- Step 2 : Setting up the remote commander (continued)
  - Notes
    - • If the TV uses a different remote control system from the one programmed to work with the VCR, ...
    - • If you enter a new code number, the code number previously entered will be erased.
    - • If you remove the batteries of the remote commander for more than a few minutes, the code numbe...
  - Connecting the VCR
    - • If your TV has a EURO-AV connector, see below.
    - • If your TV does not have a EURO-AV connector, see page 14.
    - If your TV has a EURO-AV (Scart) connector
      - 1
      - 2
- Step 3 : Connecting the VCR (continued)
  - 3
  - 4
  - Notes
    - • If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in the OTHER OPTI...
    - • For correct connection of the SmartLink, please refer to your TV instruction manual.
  - About the SMARTLINK features
    - *1 “MEGALOGIC” is a registered trademark of Grundig Corporation.
    - *2 “EASYLINK” is a trademark of Philips Corporation.
    - *3 “Q-Link” is a trademark of Panasonic Corporation.
    - *4 “EURO VIEW LINK” is a trademark of Toshiba Corporation.
    - *5 “T-V LINK” is a trademark of JVC Corporation.
    - Note
      - • Not all the TVs respond to the functions above.
- Step 3 : Connecting the VCR (continued)
  - If your TV does not have a EURO-AV (Scart) connector
    - 1
    - 2
    - 3
    - Note
      - • When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in...
  - Additional connections
    - 1
    - 2
    - 3
    - 4
- Step 3 : Connecting the VCR (continued)
  - Note
    - • You cannot watch satellite programmes on the TV while recording unless you record a satellite p...
  - Tuning your TV to the VCR
    - 1
    - 2
    - 3
    - 4
- Step 4 : Tuning your TV to the VCR (continued)
  - 5
  - 6
  - 7
  - To check if the TV tuning is correct
  - To obtain a clear picture from the VCR
    - Notes
      - • When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in...
      - • If you set the wrong TV system, you may have no sound or may be distorted.
  - Setting up the VCR with the Auto Set Up function
    - Before you start ...
      - • Turn on the satellite tuner if it is connected to the VCR only by the aerial cable and not to t...
        1
        2
- Step 5 : Setting up the VCR with the Auto Set Up function (continued)
  - 3
  - To cancel the Auto Set Up function
    - Tip
      - • If you want to change the language for the on-screen display from the one preset in the Auto Se...
    - Notes
      - • Do not cancel the Auto Set Up function during step 3. If you do, repeat Auto Set Up from the be...
      - • Sometimes, when you operate the Auto Set Up function, some of the settings (ShowView, timer etc...
  - Setting the clock
    - Setting the clock manually
      - 1
      - 2
- Step 6 : Setting the clock (continued)
  - 3
  - 4
  - 5
  - 6
  - 7
  - 8
  - Tip
    - • To change the digits during setting, press CURSOR < to return to the item to be changed, and se...
  - Note
    - • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Step 6 : Setting the clock (continued)
  - Changing the station for the Auto Clock Set function
    - 1
    - 2
    - 3
    - 4
    - 5
    - 6
    - 7
    - Tips
      - • To change the digits during setting, press CURSOR < to return to the item to be changed, and se...
      - • If you set AUTO ADJUST to ON, the Auto Clock Set function is activated whenever the VCR is turn...
    - Note
      - • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Selecting a language
  - 1
  - 2
  - 3
  - Note
    - • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Presetting channels
  - 1
  - 2
  - 3
  - 4
  - 5
  - 6
  - CC0C0
    - 7
    - 8
    - 9
    - 10
  - Presetting channels (continued)
    - Disabling unwanted programme positions
      - 1
      - 2
    - If the picture is not clear
      - 1
      - 2
      - 3
      - 4
      - 5
      - Note
        • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Setting/changing the station names
  - 1
  - 2
  - 3
  - Setting/changing the station names (continued)
    - 4
    - 5
    - 6
    - 7
    - 8
    - 1 Press CURSOR M/m to select a character. Each time you press CURSOR M, the character changes as ...
    - 2 Press CURSOR, to set the next character. The next space is highlighted. To correct a character,...
      - Note
        • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Changing/disabling programme positions
  - Changing programme positions
    - 1
    - 2
  - Changing/disabling programme positions (continued)
    - 3
    - 4
    - 5
    - 6
    - 7
    - Disabling unwanted programme positions
      - 1
      - 2
  - Changing/disabling programme positions (continued)
    - 3
    - 4
    - 5
    - 6
    - Notes
      - • The menu disappears automatically if you don’t proceed for more than a few minutes.
      - • Be sure to select the programme position you want to disable correctly. If you disable a progra...
- Connecting the Satellite tuner
  - Connecting the Satellite tuner (continued)
    - Setting the Satellite tuner
      - 1
      - 2
      - 3
      - 4
      - 5
      - 6
      - Note
        • To record a satellite programme, press INPUT SELECT button to display "L4" in the display window.
- Setting the PAY-TV/Canal Plus decoder
  - Connecting a decoder
  - Setting PAY-TV/Canal Plus channels
    - 1
    - 2
    - 3
  - Setting the PAY-TV/Canal Plus decoder (continued)
    - 4
    - 5
    - 6
    - 7
    - 8
    - 9
    - 10
    - 11
    - 12
    - 13
  - Setting the PAY-TV/Canal Plus decoder (continued)
    - 14
    - 15
    - 16
    - Notes
      - • The menu disappears automatically if you don’t proceed for more than a few minutes.
      - • To superimpose subtitles while watching PAY-TV/Canal Plus programmes, make both decoder-VCR and...
      - • When you watch PAY-TV/Canal Plus programmes using the aerial input of the TV, press t TV/VIDEO ...
      - • Some PAY-TV/Canal Plus decoders may not work if you set the PAY-TV/CANAL + setting to ON. In th...
    - Basic Operations
- Playing a tape
  - 1
  - 2
  - 3
  - Additional tasks
  - To set the colour system
  - If the playback picture has no colour or streaks appear during playback, set the COLOUR SYSTEM op...
  - To play an NTSC-recorded tape
  - To use the time counter
    - Notes
      - • The counter resets to “0:00:00” whenever a tape is reinserted.
      - • The counter stops counting when it comes to a portion with no recording.
      - • The time counter does not appear on the TV screen when using an NTSC-recorded tape.
      - • Depending on your TV, the following may occur while playing an NTSC-recorded tape:
        – The picture becomes black and white.
        – The picture shakes.
        – No picture appears on the TV screen.
        – Black streaks appear horizontally on the TV screen.
        – The colour density increases or decreases.
      - • If you playback a tape in LP or EP mode with NTSC system, the sound is heard in monaural.
  - Starting playback automatically with one button (One Touch Play)
    - 1
    - 2
    - Tip
      - • When there already is a tape in the VCR, the VCR and the TV turn on, the TV is set to the video...
    - Note
      - • When you use the One Touch Play function, leave the TV on or in the standby mode.
- Recording TV programmes
  - 1
  - 2
  - 3
  - 4
  - 5
  - To stop recording
  - Recording TV programmes (continued)
    - To check the remaining time
    - To watch another TV programme while recording
      - 1
      - 2
    - To protect a recording
      - Tips
        • To select a programme position, you can use the programme number buttons on the remote commande...
        • The display appears on the TV screen indicating information about the tape, but the information...
        • If you don’t want to watch TV while recording, you can turn off the TV. When using a decoder, m...
      - Notes
        • The display does not appear during still (pause) mode or slow-motion playback.
        • The display will not appear while playing an NTSC-recorded tape.
        • If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will not...
        • You cannot watch a PAY-TV/Canal Plus programme while recording another PAY-TV/Canal Plus progra...
        • The remaining time is intended for rough measurement only.
        • The remaining time will be displayed only about 30 seconds after the tape is inserted.
    - Recording what you are watching on the TV (TV Direct Rec)
      - 1
      - 2
      - Tips
        • The TV indicator appears in the display window after you press z REC in some situations such as:
        – when you are watching a source connected to the TV’s line input, or
        – when the TV tuner preset data for the programme position is different from the data in the VCR ...
        • If there is a tape with its safety tab in place in the VCR, the VCR automatically turns on and ...
        • You can turn the TV Direct Rec function ON and OFF in the OTHER OPTIONS menu (see page 73).
      - Notes
        • You cannot record what you are watching using this method when the VCR is in the following mode...
        • When the TV indicator is lit in the display window, do not turn off the TV nor change the TV pr...
- Recording TV programmes using the ShowView system
  - 1
  - 2
  - Recording TV programmes using the ShowView system (continued)
    - 3
    - 4
    - 5
    - 6
    - 1 Press CURSOR </, to highlight the item you want to change.
    - 2 Press CURSOR M/m to reset it.
      - To stop recording
      - Daily/weekly recording
      - TODAY t SU-SA (Sunday to Saturday) t MO-SA (Monday to Saturday) t MO-FR (Monday to Friday) t SA (...
      - Timer recording with VPS/PDC signals
  - Recording TV programmes using the ShowView system (continued)
    - To use the VCR after setting the timer
      - • Reset the counter.
      - • Display tape information on the TV screen.
      - • Check the timer settings see “Setting the timer manually” on page 57.
      - • Watch another TV programme.
        Tips
        • To set the programme position with a two digit number, press –/– – (ten’s digit) button followe...
        • To set the programme position, you can also use the PROG +/– or programme number buttons.
        • To set the tape speed, you can also use the SP/LP button.
        • When you are recording a programme in the SP mode and the remaining tape becomes shorter than t...
        • To check, change, or cancel the programme setting, press CURSOR </, to choose LIST, then press ...
        Notes
        • When setting the timer with VPS/PDC signals, enter the start and stop times exactly as indicate...
        • If the VPS/PDC signal is too weak or the broadcasting station failed to transmit VPS/PDC signal...
        • The indicator flashes in the display window when you press ?/1 with no tape inserted.
        • The VPS/PDC function is automatically set to OFF for the timer recording of a satellite programme.
        • When you set TIMER OPTIONS to STANDARD in the OTHER OPTIONS menu, the SHOWVIEW menu does not ap...
- Setting the timer manually
  - Setting the timer manually (continued)
    - 1
    - 2
    - 3
    - 4
    - 1 Press CURSOR , to highlight each item in turn.
    - 2 Press CURSOR M/m to set each item.
      - To stop recording
      - Daily/weekly recording
      - TODAY t SU-SA (Sunday to Saturday) t MO-SA (Monday to Saturday) t MO-FR (Monday to Friday) t SA (...
        Tips
        • To set the programme position, you can also use the PROG +/– or programme number buttons.
        • To set the tape speed, you can also use the SP/LP button.
        • When you are recording a programme in the SP mode and the remaining tape becomes shorter than t...
        • Even if you set TIMER OPTIONS to SHOWVIEW in the OTHER OPTIONS menu, you can set the timer manu...
        Notes
        • When setting the timer with VPS/PDC signals, enter the start and stop times exactly as indicate...
        • If the VPS/PDC signal is too weak or the broadcasting station failed to transmit VPS/PDC signal...
        • The indicator flashes in the display window when you press ?/1 with no tape inserted.
    - Additional Operations
- Playing/searching at various speeds
  - To resume normal playback
  - Using the shuttle ring
    - To use the shuttle ring in normal mode
    - To use the shuttle ring in jog mode
  - Playing/searching at various speeds (continued)
    - Tip
      - • Adjust the picture using the TRACKING +/– buttons if:
        – Streaks appear while playing in slow motion.
        – Bands appear at the top or bottom while pausing.
        – The picture shakes while pausing.
      - To set tracking to the centre position, press both buttons (+/–) at the same time.
    - Notes
      - • The playback sound is muted during the operations in the above table.
      - • In the LP mode, noise may appear or there may be no colour.
      - • If the playback mode mark doesn’t appear on the TV screen, press DISPLAY.
- Setting the recording duration time
  - 1
  - 2
  - To extend the duration
  - To cancel the duration
  - To stop recording
    - Note
      - • You cannot display the current tape time in the display window when setting the recording durat...
- Checking/changing/cancelling timer settings
  - 1
  - 2
  - 3
  - 4
  - 5
  - 6
  - When the timer settings overlap
    - Tip
      - • In step 5 above, you can check the TIMER LIST by selecting LIST and pressing OK. Press MENU to ...
- Recording stereo and bilingual programmes
  - In ZWEITON (German stereo) system
    - To select bilingual sound while recording
  - In NICAM system
    - To select the sound while recording
    - Stereo programme
      - * Usually the mixed sound of left and right channels (monaural)
    - Bilingual programme
      - * Usually the main sound (monaural)
  - Selecting the sound during playback
  - How sound is recorded on a video tape
    - Notes
      - • To listen to playback sounds in stereo, you must use the EURO-AV or AUDIO OUT connections.
      - • When you play a tape recorded in monaural, the sound is heard in monaural regardless of the AUD...
      - • If the AUDIO MONITOR button does not function, check that AUDIO MIX in the AUDIO OPTIONS menu i...
      - • If HIFI AUDIO is set to STANDARD, the standard sound will be recorded on both the hi-fi and nor...
- Searching using the index function
  - 1
  - 2
  - To stop searching
    - Note
      - • No index signal will be added when recording starts from recording pause. However, an index sig...
- Adjusting the picture
  - Adjusting the tracking
  - About the Reality Regenerator (RR) function
  - About the Optimum Picture Control (OPC) function
    - OPC playback
  - Adjusting the picture (continued)
    - OPC recording
    - To deactivate the OPC function
    - About the Digital Noise Reduction (DNR) function
      - Notes
        • You can adjust the tracking for the NTSC-recorded tape but the tracking meter won’t be displayed.
        • With the Auto Long Play function on, the OPC function will work only in SP mode. If the tape sp...
        • There is a delay of about ten seconds before the VCR actually starts recording while the VCR an...
- Changing menu options
  - 1
  - 2
  - 3
  - 4
  - 5
  - VIDEO OPTIONS menu
  - Changing menu options (continued)
    - Note
      - • When you playback with the EDIT function ON, the OPC and the SHARPNESS functions don’t work.
    - AUDIO OPTIONS menu
    - TAPE OPTIONS menu
    - OTHER OPTIONS menu
      - Note
        • When you set a timer recording, the indicators in the display window remain on, even though POW...
- Editing with another VCR or stereo system
  - How to connect to record on this VCR
    - Tip
      - • You can also use the LINE-4 IN connector or the LINE-3 IN jacks instead.
    - Notes
      - • Make sure you connect the plugs to jacks of the same colour.
      - • If the other VCR is a monaural type, leave the red plugs unconnected.
      - • If you connect this VCR to both the LINE IN and LINE OUT jacks of the other VCR, select the inp...
    - How to connect to a stereo system
  - Operation (when recording on this VCR)
    - 1
    - 2
    - 3
    - 4
    - To stop editing
      - Tip
        • To cut out unwanted scenes while editing, press X PAUSE on this VCR when an unwanted scene begi...
      - Note
        • If you start editing following the procedure above, the VCR won’t start recording with the OPC ...
- Audio dubbing
  - 1
  - 2
  - 3
  - 4
  - 5
  - 6
  - To stop while editing
    - Note
      - • After you use this feature, the audio in playback mode is automatically set to monaural.
  - To listen to both the hi-fi and normal audio
  - SmartFile function
- About the SmartFile function
  - Recording using the SmartFile function (page80)
  - Selecting and playing a programme (page85)
  - Checking the contents of a tape (page86)
  - Labelling a recorded programme and tape (page88)
  - Registering the contents of a recorded tape in the SmartFile label (page96)
  - Protecting a recorded programme (page98)
  - Erasing the data of an unwanted programme (page100)
  - Running a demonstration
- Recording using the SmartFile function
  - Attaching the SmartFile label to the cassette
    - Note on the purchase of SmartFile labels
      - • If you want to order additional SmartFile labels, contact your nearest Sony service facility.
      - Notes
        • The SmartFile label is equipped with a memory chip. The memory chip may be damaged and cannot b...
        • Do not leave the SmartFile label in a place subject to excessive dust or dirt, direct sunlight,...
        • If you attach the SmartFile label to a shorter tape than an E-30, the SmartFile function may no...
  - Recording a programme on the SmartFile tape
    - 1
    - 2
    - 3
    - Tip
      - • You can protect a recorded programme from accidental over-recording or erasure (see page 98).
    - Note
      - • If you press the PAUSE button one or more times during recording, thereby creating short length...
  - Recording using the SmartFile function (continued)
    - Checking the information of a recorded programme
      - Tip
        • You can manually name a recorded programme and select the category. You can also name the Smart...
      - Notes
        • If you don’t set the clock or the clock isn’t set to the correct time and date, the recording s...
        • When you set the AUTO LONG PLAY option to ON in the TAPE OPTIONS menu, and the tape speed autom...
        • The recording time length in the SmartFile list is an estimation and may be slightly different ...
    - Recording after locating the Blank Time space
      - 1
      - 2
      - 3
      - 4
  - Recording using the SmartFile function (continued)
    - 5
    - 6
    - 7
    - Notes
      - • You may not be able to locate the beginning of the Blank Time space correctly in the above step...
      - • If a newly recorded programme overlaps a stored programme, the stored programme information is ...
- Selecting and playing a programme
  - 1
  - 2
  - 3
  - 4
  - To stop searching
    - Note
      - • You may not be able to locate the beginning of the selected programme correctly when : - the Sm...
- Checking the contents of a tape
  - 1
  - 2
  - 3
  - Tip
    - • If you press a button other than SP/LP or CURSOR M/m, the SmartFile check list disappears.
  - Notes
    - • You cannot display the SmartFile check list while : - you display the SmartFile list of a diffe...
    - • If the SmartFile check list doesn’t appear on the TV screen, try again by drawing the SmartFile...
    - • The menu disappears automatically if you don’t proceed for more than a few minutes.
- Labelling a recorded programme and tape
  - Setting the TV guide page number
    - 1
    - 2
    - 3
    - 4
    - 5
    - 6
    - 7
  - Labelling a recorded programme and tape (continued)
    - Notes
      - • In step 4 above, enter "000" if you don’t want to use the TV guide page number for automatic la...
      - • Refer to the Teletext information on your TV screen to get the TV guide page number with the pr...
      - • If the Teletext TV guide has a page which always shows the programmes for the current day, this...
      - • If you start recording more than two minutes before the programme is scheduled to start, the co...
      - • If you set a timer recording with VPS/PDC OFF, the title information will be transferred in the...
      - • Note that this function may not work correctly with programmes broadcast from some stations.
      - • When the recording starts and if at that moment the Broadcast system updates the Teletext infor...
      - • You cannot get the label information from the sources through the LINE input or the satellite c...
    - Labelling a recorded programme manually
      - 1
      - 2
      - 3
  - Labelling a recorded programme and tape (continued)
    - 4
    - 5
    - 1 Press CURSOR M/m to select a character. Each time you press CURSOR M, the character changes as ...
    - 2 To set the next character, press CURSOR,. The cursor moves to the next position.
    - 3 Repeat steps 1 and 2 to label the programme.
      - 6
      - 7
      - 8
      - 9
      - To erase the programme label
      - To erase the selected category
    - To label a regularly scheduled timer-recorded programme
  - Labelling a recorded programme and tape (continued)
    - Labelling a tape
      - 1
      - 2
      - 3
      - 4
      - 5
      - 1 Press CURSOR M/m to select a character. Each time you press CURSOR M, the character changes as ...
      - 2 To set the next character, press CURSOR ,. The cursor moves to the next position.
      - 3 Repeat steps 1 and 2 to label the tape.
        6
        7
        To erase the tape title
- Registering the contents of a recorded tape in the SmartFile label
  - 1
  - 2
  - To stop registration to the SmartFile label
  - To check the information of a registered programme
    - Tips
      - • The programmes recorded on the tape can be registered again in a SmartFile label that already c...
      - • If the SmartFile label contains stored programme data that includes protected programmes, a mes...
    - Notes
      - • Programme data is not registered correctly in the SmartFile label when :
        – the programme length is about 20 minutes or less in LP mode or about 11 minutes in SP mode.
        – the programme does not have an index signal or the index signal has been recorded over and erased.
        – the tape is damaged or dirty.
      - • If you don’t set the clock or the clock isn’t set to the correct date, the registration date wo...
      - • After you press SMARTFILE GENERATOR and start registration, registration is interrupted if you ...
      - • When you set AUTO LONG PLAY to ON in the TAPE OPTIONS menu, and the tape speed automatically ch...
      - • The estimated position of the registered programmes may not be correct in case of many short pr...
- Protecting a recorded programme
  - 1
  - 2
  - 3
  - 4
  - 5
  - To unlock the protected programme
    - Tips
      - • When you start recording from a position prior to the protected programme, the recording automa...
      - • If you protect a programme just after the Blank Time space, BLANK TIME becomes shortened by abo...
      - • If you try to record on a SmartFile tape containing a protected programme, a message indicating...
    - Notes
      - • When you record another programme just after a protected programme, locate the beginning of the...
      - • If you insert a SmartFile tape which contains a protected programme or protect a programme for ...
      - • If the SmartFile list contains 12 protected programmes, the next programme you record won’t be ...
      - • When you try to turn off the VCR after setting a ShowView timer recording on the protected prog...
      - • The protecting function may not work with an NTSC-recorded tape.
- Erasing the data of an unwanted programme
  - 1
  - 2
  - 3
  - 4
  - 5
  - Notes
    - • You cannot erase a protected programme from the SmartFile list. You have to first unlock the pr...
    - • The erased programme disppears from the SmartFile list, but it still remains on the tape.
    - • If a programme is left about 11 minutes or less in SP mode or about 20 minutes or less in LP mo...
  - Additional Information
- Troubleshooting
  - Problem summary
  - Troubleshooting (continued)
  - Troubleshooting (continued)
- Specifications
  - Channel coverage
  - RF output signal
  - Aerial out
  - iLINE-1 (TV)
  - DECODER/t LINE-4 IN
  - LINE-2 IN
  - LINE-3 IN
  - LINE-2 OUT
  - Power requirements
  - Power consumption
  - Operating temperature
  - Storage temperature
  - Dimensions
  - Mass
  - Remote commander (1)
  - R6 (size AA) batteries (2)
  - Aerial cable (1)
  - Audio cable (1)
  - EURO-AV cable (1)
  - SmartFile labels (10)
  - Design and specifications are subject to change without notice.
- Index to parts and controls
  - Front panel
    - A ?/1 ON/STANDBY button/indicator (6)
    - B SMARTFILE indicator (86)
    - C SMARTFILE sensor (86)
    - D REALITY REGENERATOR (RR) indicator (69)
    - E Tape compartment
    - F SMARTFILE button (81)
    - G CURSOR M/m buttons (86)
    - H Z EJECT button (46)
    - I m REW (rewind) button (46)
    - J H PLAY button (46)
    - K M FF (fast-forward) button (46)
    - L JOG button/indicator (60)
    - M Shuttle ring (60)
    - N z REC (record) button (48), (74)
    - O x STOP button (46)
    - P X PAUSE button (46)
    - Q OK button
    - R PROGRAM/TRACKING +/– buttons (19), (69)
    - S DIGITAL NOISE REDUCTION button (70)
    - T REALITY REGENERATOR button (69)
    - U AUTO SET UP (19)/ RF (Radio Frequency) CHANNEL button (17)
    - V SMARTFILE GENERATOR button
    - W COMMAND MODE Switch (7)
    - X LINE-2 IN VIDEO/AUDIO L/R jacks (74)
    - Y DIGITAL NOISE REDUCTION (DNR) indicator (70)
    - Z Remote sensor (5)
  - Index to parts and controls (continued)
    - Display window
      - A Timer indicator (55), (57)
      - B VPS (Video Programme System)/PDC (Programme Delivery Control) indicator (55)
      - C Audio Dubbing indicator (76)
      - D OPC (Optimum Picture Control) indicator (69)
      - E SMARTLINK indicator (13)
      - F Tape speed indicators (49)
      - G VIDEO indicator (49)
      - H TV indicator (51)
      - I STEREO indicator (66)
      - J NICAM indicator (66)
      - K Time counter/clock/line/programme position indicator (17), (46), (49)
      - L Remaining time indicator (50)
      - M Tracking indicator (69)
      - N EDIT indicator (75)
      - O BL (Blank Time space) indicator (86)
      - P Tape/recording indicator (49)
    - Rear panel
      - A Mains lead (11), (14)
      - B LINE-3 IN AUDIO L/R/VIDEO ENTREE LIGNE-3 AUDIO G/D/VIDEO
      - C i LINE-1 (TV) i LIGNE-1 (TV) connector (11), (40)
      - D DECODER/t LINE-4 IN DECODEUR/t ENTREE LIGNE-4 connector (40)
      - E AERIAL IN ANTENNE ENTREE connector (11), (14)
      - F AERIAL OUT ANTENNE SORTIE connector (11), (14)
      - G NTSC PB (Play Back) switch (45)
      - H LINE-2 OUT AUDIO L(left)/R (right)/VIDEO SORTIE LIGNE-2 AUDIO G/D/VIDEO (15)
    - Remote commander
      - A Z EJECT button (46)
      - B Menu buttons (6) MENU button CURSOR M/m/</, buttons OK button
      - C TIMER button (52), (57)
      - D AUDIO MONITOR button (6), (66)
      - E CLEAR button (45), (52), (64)
      - F AUDIO DUB button* (76)
      - G COUNTER/REMAIN button* (50)
      - H Fastext button*
      - I Fastext button*
      - J t TV/VIDEO button (6)
      - K DISPLAY button (50)
      - L WIDE button (for TV) (7)
      - M SP (Standard Play)/LP (Long Play) button (48)
      - N z REC (record) button (48), (63), (75)
      - O ./> INDEX SEARCH buttons (68) a TV power on/TV mode select button (for TV) (7) / (Teletext) but...
      - P m REW (rewind) button (46), (60)
      - Q M FF (fast-forward) button (46), (60)
      - R H PLAY button (46), (60)
      - S x STOP button (46), (63)
      - T Shuttle ring (60)
      - * FASTEXT buttons (for TV)
        U TV / VIDEO remote control switch (5)
        V ?/1 (on/standby) button (6), (52)
        W COMMAND MODE Switch (7)
        X SMARTFILE button (81)
        Y Programme number buttons (6)
        Z –/– –(ten’s digit) button (6), (50)
- Menu chart
  - This VCR is equipped with an on-screen indication system which allows you a visual, quick and eas...
Index
- A
- C
- D
- E
- H
- I
- L
- M
- N
- O
- P
- R
- S
- T
- V
- Z

Sony SLV-SF99EN Manual

Documents

Sony SLV-SF99EN User Manual [PDF]

Table of Contents