Sony KDL-40Z5810

Sony KDL-40Z5800 KDL-40Z5810 KDL-46Z5800 User Manual

Table of Contents

  • NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
    • A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
    • Should the fuse in the plug supplied need to be replaced with the same rating of fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used.
    • When an alternative type of plug is used it should be fitted with the same rating of fuse, otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board.
    • If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse...
    • Open the fuse compartment with a blade screwdriver, and replace the fuse. Please refer to the illustration that actually equipped with the product.
  • Start-up Guide
    • Before Use
      • To check the accessories
      • To insert batteries into the remote
    • 1: Attaching the stand
      • 1 Open the carton box and take out the stand and the screws.
        • 2 Place the TV set on the stand.
        • 3 Fix the TV to the stand according to the arrow marks that guide the screw holes using the supplied screws.
      • ~
    • 2: Connecting an aerial/ antenna/Set Top Box/ recorder (e.g. DVD recorder)
    • 3: Preventing the TV from toppling over
      • 1 Install a wood screw (4 mm in diameter, not supplied) in the TV stand.
        • 2 Install a machine screw (M4 ° 20, not supplied) into the screw hole of the TV.
        • 3 Tie the wood screw and the machine screw with a strong cord.
    • 4: Bundling the cables
      • ~
    • 5: Performing the initial Set-up
      • 1
      • 2
      • 3
      • 4
        • 1 Press F/f to select the channel you want to move to a new position, then press .
        • 2 Press F/f to select the new position for the channel, then press .
      • ~
    • Adjusting the viewing angle of the TV
      • Adjust the angle left and right (swivel)
    • Detaching the Table-Top Stand from the TV
      • ~
    • Safety Information
    • Precautions
    • Remote and TV Controls/Indicators
      • Remote and TV controls
        • z
      • ~
      • ~
      • ~
      • ~
        • z
      • ~
      • ~
        • Indicators
        • About the operation guide on the TV screen
  • Watching TV
    • Watching TV
      • 1 Press 1 on the TV to turn on the TV.
        • 2 Press DIGITAL to switch to digital or satellite mode, or press ANALOG to switch to analogue mode.
        • 3 Press the number buttons or PROG +/- to select a TV channel.
  • Instruction Manual
    • Instruction Manual
      • Displays the instruction manual on the screen.
    • Navigating through the Instruction Manual
      • 1 Press HOME to display the XMB™.
        • 2 Press G/g to select “Settings”.
        • 3 Press F/f to select “Instruction Manual”, then press .
        • 4 Press F/f to select topic from the Table of Contents, then press . Use the corresponding coloured button to go to next or prev...
        • 5 Press HOME to exit.
      • ~
  • Additional Information
    • Installing the Accessories (Wall-Mount Bracket)
      • To Customers:
      • To Sony Dealers and Contractors:
      • ~
        • TV installation dimensions table
          • Figures in the above table may differ slightly depending on the installation.
          • The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to “Specifications” (page 19) for its weight.
        • Screw and Hook locations diagram/table
    • Specifications
      • * 1080p timing when applied to the HDMI input will be treated as a video timing and not a PC timing. This affects the “Video Settings” menu and “Screen” menu settings. To view PC contents, set “Screen Format” to “Wide” and “Display Area” to “Full Pixel”.
      • ~
    • Troubleshooting
      • 1 Count how many times the 1 (standby) indicator flashes between each two second break.
        • 2 Press 1 on the TV to turn it off, disconnect the mains lead/AC power cord, and inform your dealer or Sony service centre of how the indicator flashes (number of flashes).
      • 1 Check the items in the tables below.
        • 2 If the problem persists, have your TV serviced by qualified service personnel.
      • How the switchover affects your TV equipment:
      • How to re-tune:
        • 1 Press "HOME" on the remote
          • 2 Press G/g to select "Settings"
          • 3 Press F/f to select "Digital Set-up", then press
          • 4 Press to select "Digital Auto Tuning"
          • 5 Press G to select "Yes" then press to start "Digital Auto Tuning"
          • 6 Follow the on screen instructions.