Toshiba 46HM95 52HM95 62HM95 Manual

Thursday, May 4, 2017
Download

OWNER’S MANUAL Integrated High Definition DLP™ Projection Television Compatible with the new Toshiba TM Audio/Video Hard Drive Recorder! See pages 23 and 50 for details. HIGH-DEFINITION TELEVISION For an overview of steps for setting up and using your new TV, see page 8. Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer or your cable or satellite provider. Note: If the TV is powered off and then on again quickly CONSUMER PR when the lamp unit is hot, it may take several minutes for RI CA OD E the picture to appear on-screen. This is a property of DLP TOSHIBA AM UCT S, L.L.C. TV lamp technoplogy and is not a sign of malfunction. For details, see “IMPORTANT NOTICE ABOUT HOT LAMP RESTART” on page 8. O IS 45 140 6 01 FILE N o. A 9 Owner’s Record 46HM95 The model number and serial number are on the back of your TV. Record these numbers in the spaces below. 52HM95 Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: 62HM95 Serial number: © 2005 TOSHIBA CORPORATION 23566650A All Rights Reserved [A-PDFO] HM95_R1_001_061505 6/24/05, 7:44 PM

Dear Customer, NOTICE OF POSSIBLE TV STAND INSTABILITY Thank you for purchasing this Toshiba TV. This manual will CAUTION: This television is for use only with help you use the many exciting features of your new TV. the Toshiba stand listed below. Use with other Before operating the TV, please read this manual carts or stands is capable of resulting in instability completely, and keep it nearby for future reference. causing possible injury. Television Stand Model 46HM95 ST4665 Safety Precautions 52HM95 ST5265 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC 62HM95 ST6265 SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE TO CATV INSTALLERS IN THE U.S.A. WARNING This is a reminder to call the CATV system installer’s attention to Article RISK OF ELECTRIC SHOCK! 820-40 of the U.S. NEC, which provides guidelines for proper grounding DO NOT OPEN. and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, as practical. For additional antenna grounding information, see items 27 DO NOT REMOVE COVER (OR BACK). NO USER- and 28 on page 4. SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. (This does not apply to "Lamp unit replacement and care" on pages 103-105 of this manual.) Child Safety The lightning flash with arrowhead symbol, within an It Makes A Difference equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the Where Your TV Stands product’s enclosure that may be of sufficient magnitude Congratulations on your purchase! to constitute a risk of electric shock to persons. As you enjoy your new TV, keep these safety tips in mind: The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important The Issue operating and maintenance (servicing) instructions in the literature accompanying the appliance.  If you are like most consumers, you have a TV in your home. Many homes, in fact, have more than one TV.  The home theater entertainment experience is a growing trend, and larger Lamp Unit Replacement TVs are popular purchases; however, they are not always supported on the proper TV stands.  Sometimes TVs are improperly secured or inappropriately CAUTION: HOT SURFACE! situated on dressers, bookcases, shelves, desks, audio speakers, The temperature of the lamp chests, or carts. As a result, TVs may fall over, causing immediately after use exceeds unnecessary injury. 392°F (200°C). Touching the Toshiba Cares! lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE  The consumer electronics industry is committed to making home entertainment enjoyable and safe. REPLACING IT.  The Consumer Electronics Association formed the The lamp in this product has a limited service life. The length of Home Entertainment Support Safety Committee, comprised of TV and consumer electronics furniture manufacturers, to service life varies depending on product use and user settings. advocate children’s safety and educate consumers and their If you use the lamp beyond its service life: families about television safety. • you may notice a reduction in the colors and/or brightness of the picture, at which time you should replace the lamp unit; and Tune Into Safety • the strength of the quartz glass in the lamp will be reduced  One size does NOT fit all! Use appropriate furniture large enough to and the lamp may rupture. If the lamp ruptures, the TV will support the weight of your TV (and other electronic components). not åoperate until the lamp unit is replaced.  Use appropriate angle braces, straps, and anchors to secure your furniture to the wall (but never screw anything directly into the TV). • Dispose of the used lamp unit by the approved method for your area.  Carefully read and understand the other enclosed instructions for proper use of this product. See “Lamp unit replacement and care”  Do not allow children to climb on or play with furniture and TVs. on pages 103–105.  Avoid placing any item on top of your TV (such as a VCR, remote control, or toy) that a curious child may reach for. Note: The lamp unit contains mercury.  Remember that children can become excited while watching a program Disposal of mercury may be regulated due to and can potentially push or pull a TV over. environmental considerations. For disposal or recycling  Share our safety message about this hidden hazard of the home with information, contact your local authorities or the Electronic your family and friends. Thank you! Industries Alliance (www.eiae.org). 2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 NOTE: NEVER CONNECT THIS TV www.CE.org TO A PERSONAL COMPUTER (PC). CEA is the Sponsor, Producer and Manager of the International CES® THIS TV IS NOT INTENDED FOR USE WITH A PC. 2 HM95_R1_002-04_061505 2 6/24/05, 7:45 PM

Important Safety Instructions 16) WARNING: This product contains a lamp to project the picture, and requires special safety precautions: 1) Read these instructions. • See pages 103–105 for instructions on lamp unit 2) Keep these instructions. replacement and care. 3) Heed all warnings. • DO NOT attempt to service this product except as 4) Follow all instructions. specified on pages 103–105. The only user- serviceable item in this product is the lamp unit. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. Installation, Care, and Service 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Installation Follow these recommendations and precautions and heed all 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including warnings when installing your TV: amplifiers) that produce heat. 17) Never modify this equipment. Changes or modifications 9) Do not defeat the safety purpose of the polarized or may void: a) the warranty, and b) the user’s authority to grounding type plug. A polarized plug has two blades operate this equipment under the rules of the Federal with one wider than the other. A grounding type plug has Communications Commission. two blades and a third grounding Wide blade prong. The wide blade or the third prong are provided for your safety. 18) DANGER: RISK OF SERIOUS PERSONAL If the provided plug does not fit into INJURY, DEATH, OR EQUIPMENT your outlet, consult an electrician DAMAGE! Never place the TV on for replacement of the obsolete outlet. an unstable cart, stand, or table. The TV may fall, causing serious personal injury, 10) Protect the power cord from being death, or serious damage to the TV. walked on or pinched, particularly at plugs, convenience receptacles, and 19) Never place or store the TV in direct sunlight; hot, humid the point where it exits the apparatus. areas; areas subject to excessive dust or vibration; or 11) Only use attachments/accessories specified by the locations with temperatures at or below 41°F (5°C). manufacturer. 20) Always place the TV on the floor or a sturdy, level, stable 12) Use only with the cart, stand, tripod, bracket, or table specified by the surface that can support the weight of the unit. manufacturer, or sold with the apparatus. When a cart is used, use 21) Never expose the apparatus to dripping or splashing or caution when moving the cart/apparatus place items such as vases, aquariums, any other item filled combination to avoid injury from tip-over. with liquid, or candles on top of the TV. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 22) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to 14) Refer all servicing to qualified service personnel. allow proper ventilation. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen 23) Never block or cover the slots or openings in the TV into the apparatus, the apparatus has been exposed to cabinet back, bottom, and sides. Never place the TV: rain or moisture, does not operate normally, or has been • on a bed, sofa, rug, or similar surface; dropped. • too close to drapes, curtains, or walls; or 14a) Item 14 does not apply to “Lamp unit replacement and • in a confined space such as a bookcase, built-in cabinet, care” on pages 103-105 of this manual. or any other place with poor ventilation. 14b) CAUTION: If the TV is dropped and the cabinet or The slots and openings are provided to protect the TV enclosure surface has been damaged or the TV does from overheating and to help maintain reliable operation not operate normally, take the following precautions: of the TV. • ALWAYS turn off the TV and unplug the power cord to avoid possible electric shock or fire. 24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is • To prevent personal injury, never handle the damaged subject to wear or abuse. television. • ALWAYS contact a service technician to inspect the TV 25) Never overload wall outlets and extension cords. any time it has been damaged or dropped. 15) CAUTION: To reduce the risk of electric shock, do not 26) Always operate this equipment from a 120 VAC, 60 Hz use the polarized plug with an extension cord, receptacle, power source only. or other outlet unless the blades can be inserted completely to prevent blade exposure. (continued on next page) 3 HM95_R1_002-04_061505 3 6/24/05, 7:45 PM

Installation (continued from previous page) Care (continued from previous column) 27) Always make sure the antenna system is properly 33) For added protection of your TV from lightning and power grounded to provide adequate protection against voltage surges, always unplug the power cord and disconnect the surges and built-up static charges (see Section 810 of the antenna from the TV if you leave the TV unattended or National Electric Code). unused for long periods of time. Antenna lead-in wire 34) During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the Antenna discharge unit (NEC Section 810-20) unit is being turned on or off. If these sounds become Ground clamp frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center. Grounding conductors Electric ser vice equipment (NEC Section 810-21) 35) Special care for Texas Instruments Digital Light Processing™ (DLP) lamp units: Power ser vice grounding • The lamp in this product has a limited service life. The electrode system (NEC Art 250 Par length of service life varies depending on product use or Ground clamps user settings. If you use the lamp beyond its service life: • you may notice a reduction in the colors and/or 28) DANGER: RISK OF SERIOUS PERSONAL brightness of the picture, at which time you should INJURY OR DEATH! replace the lamp unit; and • Use extreme care to make sure you are never in • the strength of the quartz glass in the lamp will be a position where your body (or any item you are in contact reduced and the lamp may rupture. If the lamp with, such as a ladder or screwdriver) can accidentally ruptures, the TV will not operate until the lamp unit is touch overhead power lines. Never locate the antenna replaced. near overhead power lines or other electrical circuits. See “Lamp unit replacement and care” on pages 103–105. • Never attempt to install any of the following during • Dispose of the used lamp unit by the approved method for lightning activity: a) an antenna system; or b) cables, your area. wires, or any home theater component connected to an antenna or phone system. • The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org). Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: Service 36) WARNING: RISK OF ELECTRIC SHOCK! 29) Always sit approximately 10–25 feet away from the TV and Never attempt to service the TV yourself, as directly in front of it as possible. The picture can appear except as specified on pages 103–105. dull if you sit too far to the left or right of the TV, or if Opening and removing the covers may expose you to sunlight or room lights reflect on the screen. Turn the TV dangerous voltage or other hazards. Failure to follow this off to check for reflections on the screen, and then remove WARNING may result in death or serious injury. Refer all the source of reflections while viewing the TV. servicing not specified in this manual to a Toshiba Authorized Service Center. 30) Always unplug the TV before cleaning. Never use liquid or 37) If you have the TV serviced: aerosol cleaners. Clean only with a soft, dry cloth. • Ask the service technician to use only replacement parts Do not spray volatile compounds, such as insecticide, on specified by the manufacturer. the cabinet. This may discolor or damage the cabinet. • Upon completion of service, ask the service technician to perform routine safety checks to determine that the TV is 31) WARNING: RISK OF ELECTRIC SHOCK! in safe operating condition. Never spill liquids or push objects of any kind into the TV cabinet slots. 38) When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV. Note: The lamp unit contains mercury. Disposal of mercury may 32) If the air temperature rises suddenly (for example, when be regulated due to environmental considerations. Dispose of the TV is first delivered), condensation may form on the the used lamp unit by the approved method for your area. lenses. This can make the picture appear distorted or the For disposal or recycling information, please contact your local color appear faded. If this happens, turn off the TV for 6 to authorities or the Electronic Industries Alliance (www.eiae.org). 7 hours to allow the condensation to evaporate. __________ Digital Light Processing, DLP™ and the DLP medallion are trademarks of Texas Instruments. 4 HM95_R1_002-04_061505 4 6/24/05, 7:45 PM

Important notes about your DLPTM projection TV 1) The light source for this TV is a projection lamp unit with a 6) Always sit approximately 10–25 feet away from the TV and as limited service life. When the lamp wears out, the picture may directly in front of it as possible. The picture quality may be become dark or black or the lamp may fail, at which time you affected by your viewing position and length of viewing time. must replace the lamp unit. See “Lamp unit replacement and If you sit too closely to the TV for too long, you may suffer from care” on pages 103–105. eye fatigue. See item 29 on page 4. 2) If you set the lamp mode to Low Power, each time you turn on 7) This TV contains several cooling fans to moderate the the TV, the lamp will start out in High Bright mode but will internal temperature. You may be able to hear the fans switch to Low Power mode in approximately 1 minute. You will for several minutes after the TV is turned off. This is a notice a change in screen brightness when this happens. This is function of the Quick Restart™ feature and is not a sign of TV normal and is not a sign of malfunction. (See page 75 for malfunction. You can set the Quick Restart™ feature to stop the details.) fans as soon as the TV is turned off. See “Setting the Quick Restart™ feature” on page 51. 3) Each time you turn on the TV, it may take several minutes for the picture to obtain full brightness. 8) The green and red LED lights at the bottom center of the TV front indicate your TV’s current status. If either light flashes, see 4) This TV’s display is manufactured using an extremely high level “LED indications” on page 99 for details. of precision technology; however, an occasional pixel (dot of 9) If you unplug the power cord, when you plug the power cord in light) may show constantly on the screen. This is a structural again the message “Now Booting…” will display on-screen property of DLP™ (Digital Light Processing™) technology in the until the picture appears, or the green LED will blink until the TV and is not a sign of malfunction. Such pixels are not visible TV enters standby mode (plugged in but not powered on). when the picture is viewed from a normal viewing distance (see This is normal and is not a sign of malfunction. item 29 on page 4). 10) When connecting an external A/V device, if you connect the 5) Depending on the media you are viewing, it is possible, although device’s video output to the TV and the device’s audio output unlikely, that a limited number of viewers may see a “rainbow to a separate audio system, the picture and sound may not effect” on the screen, which can, in rare instances, result in eye synchronize completely. fatigue. This is a rare occurrence related to technology of this type and is not a sign of TV malfunction. 11) When playing a video game on this TV, there may be a slight delay between your command (e.g., joystick, keyboard) and the picture movement on the screen. Contents Important Safety Information ............................................. 2-4 Controlling infrared remote-controlled devices Important notes about your DLP™ projection TV ............... 5 through the TV (IR pass-through) .................................. 21 Connecting IEEE1394 video devices .................................. 22 Chapter 1: Introduction .......................................................... 7 Using analog-compatible IEEE1394 devices ................... 22 Welcome to Toshiba ........................................................... 7 Supported signals ........................................................... 22 Features of your new TV .................................................... 7 Using TheaterNet™ on-screen device control .................. 22 Overview of steps for installing, setting up, and Connecting an AVHD or D-VHS recorder .................... 23 using your new TV ...................................................... 8 IEEE1394 device initialization ....................................... 23 Chapter 2: Connecting your TV ............................................ 9 IEEE1394 device management ....................................... 24 TV front touchpad and side panel controls G-LINK® connection ......................................................... 25 and connections ............................................................. 9 Chapter 3: Using the remote control ................................. 26 TV back panel connections ................................................ 10 Learning about the remote control ..................................... 26 Overview of cable types ...................................................... 11 Installing the remote control batteries ................................. 28 About the connection illustrations ...................................... 12 Using the remote control MODE button to control Connecting a digital CableCARD™ .................................... 12 your other devices ........................................................... 28 Connecting a VCR and antenna or Cable TV Remote Control functional key chart ................................. 29 (no Cable box) ............................................................... 13 Programming the remote control to operate Connecting a camcorder ..................................................... 13 your other devices ........................................................... 31 Connecting a VCR and Cable box ..................................... 14 Multi-brand remote control device codes ............................ 33 Connecting a VCR and satellite receiver ............................. 15 Connecting a DVD player with S-video, a VCR, Chapter 4: Menu layout and navigation ........................... 35 and a Cable box .............................................................. 16 Main menu layout .............................................................. 35 Connecting a DVD player with ColorStream® Setup/Installation menu layout ........................................... 36 (component video) and a VCR ....................................... 17 Navigating the menu system ............................................... 36 Connecting two VCRs ....................................................... 18 Chapter 5: TV Guide On Screen® setup ............................. 37 Connecting an HDMI™ or a DVI device to the Setting up the TV Guide On Screen® system ..................... 37 HDMI input .................................................................. 19 TV Guide On Screen® Reminder ....................................... 40 Connecting a digital audio system ...................................... 20 Turning off the TV Guide On Screen® Connecting an analog audio system .................................... 20 automatic display feature ................................................ 40 (Continued on next page) 5 HM95_R1_005-06_061505 5 6/24/05, 7:48 PM

Contents (Continued from previous page) Chapter 6: Setting up your TV ............................................. 41 Selecting the cinema mode (480i signals only) .................... 75 Selecting the menu language ............................................... 41 Selecting the lamp mode .................................................... 75 Configuring the antenna input sources ............................... 41 Using the POP features ...................................................... 76 Programming channels into the TV’s channel memory ....... 42 Using the POP double-window feature ....................... 76 Programming channels automatically .......................... 42 Switching the speaker audio (main or POP) ................ 77 Manually adding and deleting channels in the POP double-window aspect ratio ................................ 77 channel memory ..................................................... 43 Using the FREEZE feature ................................................. 78 Programming your favorite channels .................................. 44 Using the favorite channel scan feature ............................... 78 Setting up and using TheaterNet™ on-screen Adjusting the picture .......................................................... 79 device control ................................................................. 45 Selecting the picture mode .......................................... 79 Setting up TheaterNet ................................................. 45 Adjusting the picture quality ....................................... 79 Using the TheaterNet control icons ............................. 46 Using CableClear® DNR (digital noise reduction) ...... 80 TheaterNet IR device codes .................................. 47–49 Selecting the color temperature ................................... 80 Setting the AVHD device skip time .................................... 50 Using MPEG Noise Reduction ................................... 81 Setting the HDMI™ audio mode ........................................ 50 Using Dynamic Contrast ............................................ 81 Setting the time and date .................................................... 50 Using the closed caption mode ........................................... 82 Viewing the CableCARD™ menu ...................................... 51 Advanced closed captions ............................................ 82 Setting the Quick Restart feature ........................................ 51 Digital closed captions ................................................ 83 Viewing the digital signal meter ......................................... 52 Adjusting the audio ............................................................ 84 Viewing the system status ................................................... 52 Muting the sound ....................................................... 84 Chapter 7: Using the TV Guide On Screen® Using the digital audio selector ................................... 84 interactive program guide ............................................... 53 Selecting stereo/SAP broadcasts ................................... 84 Setting up the TV Guide On Screen® system ..................... 53 Adjusting the audio quality ......................................... 85 Navigating the TV Guide On Screen® system ..................... 54 Using the sub-bass system (SBS) ................................. 85 TV Guide On Screen® remote control functions ......... 54 Using the StableSound® feature ................................... 85 Video Window ........................................................... 55 Using the SRS WOW™ surround sound feature .......... 86 Panel Menus ............................................................... 55 Turning off the built-in speakers ................................. 86 Info Box ...................................................................... 56 Selecting the optical audio output format ................... 86 TV Guide On Screen® Icons ....................................... 56 Using the memory card JPEG picture viewer/MP3 audio TV Guide On Screen® Services .......................................... 57 player ............................................................................. 87 LISTINGS screen ....................................................... 57 Memory card specifications ......................................... 87 SEARCH screen .......................................................... 58 Using the JPEG picture viewer .................................... 88 RECORDINGS screen ............................................... 60 Using the MP3 audio player ....................................... 89 SCHEDULE screen .................................................... 61 Memory card care and handling .................................. 90 Record features ........................................................... 61 Setting the ON/OFF timer ................................................ 91 Remind features .......................................................... 63 Setting the sleep timer ........................................................ 91 SETUP screen ............................................................. 65 Displaying the channel banner ........................................... 92 Change system settings .......................................... 65 Understanding the auto power off feature ........................... 92 Change channel display ......................................... 65 Understanding the last mode memory feature .................... 92 Change default options .......................................... 66 Using the gray level feature ................................................. 92 Chapter 8: Using the TV’s features ..................................... 67 Chapter 9: Using the Locks menu ...................................... 93 Selecting the video input source to view ............................. 67 Entering the PIN code ....................................................... 93 Labeling the video input sources ......................................... 68 If you cannot remember your PIN code ............................. 93 Tuning channels ................................................................. 69 Changing your PIN code ................................................... 93 Using the channel browser .......................................... 69 Blocking TV programs and movies by rating (V-Chip) ......... 94 Tuning your favorite channels ..................................... 71 Blocking channels ............................................................... 95 Tuning to the next programmed channel .................... 71 Unlocking programs temporarily ........................................ 95 Tuning to a specific channel (programmed or Locking video inputs .......................................................... 95 unprogrammed) ...................................................... 71 Using the GameTimer™ ..................................................... 96 Switching between two channels using Using the front panel lock feature ....................................... 96 Channel Return ...................................................... 71 Chapter 10: Troubleshooting ................................................ 97 Switching between two channels using General troubleshooting ..................................................... 97 SurfLock™ ............................................................... 71 LED indications ................................................................. 99 Selecting the picture size ..................................................... 72 TV Guide On Screen® FAQs .................................... 100–102 Natural picture size ..................................................... 72 Chapter 11: Appendix ......................................................... 103 TheaterWide 1 picture size .......................................... 73 Lamp unit replacement ............................................ 103–105 TheaterWide 2 picture size .......................................... 73 Specifications ................................................................... 106 TheaterWide 3 picture size .......................................... 73 Limited United States Warranty ....................................... 107 Full picture size ........................................................... 73 Index .............................................................................. 110, 111 Scrolling the TheaterWide® picture .................................... 74 Using the auto aspect ratio feature ...................................... 74 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 6 HM95_R1_005-06_061505 6 6/24/05, 7:48 PM

1 Introduction Welcome to Toshiba Thank you for purchasing this Toshiba TV, one of the most innovative DLP™ projection See “Important notes about your TVs on the market. The goal of this manual is to guide you through setting up and DLP™ projection TV” on page 5. operating your TV as quickly as possible. • This manual applies to models 46HM95, 52HM95, and 62HM95. Before you start reading, check the model number on the back of your TV. • Instructions in this manual are based on using the remote control. You also can use the controls on the TV front touchpad if they have the same name as those referred to on the remote control. (MENU on the front touchpad functions as ENTER when a menu is on-screen or when the TV Guide On Screen® system is open.) • The side panel and back panel provide terminals for connecting other equipment to your TV. See page 9 for front touchpad and side panel details. See page 10 for back panel details. See pages 12–25 for instructions on connecting other devices to your TV. • Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference. Features of your new TV The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD DLP™ projection TV: • Integrated digital tuning (8VSB ATSC and QAM) eliminates the need for a separate digital converter set-top box (in most cases). • TV Guide On Screen® no-fee interactive program guide (Chapters 5 and 7). • Digital CableCARD™ slot for viewing encrypted digital Cable TV programs (page 12). • Digital recording by connecting a D-VHS digital recording device or a Toshiba Symbio™ Audio/Video Hard Drive Recorder to one of the IEEE1394 jacks. You can record high definition and standard definition material from either tuner (page 23). • Memory card slots [SD Memory Card, MultiMediaCard, MemoryStick, CompactFlash, xD-PictureCard™] for viewing JPEG files as a “slide show” (page 88) and for playing MP3 files (page 89). • TheaterNet™ icons for on-screen control of external IR and IEEE1394 devices (page 45). • Two IEEE1394 ports for multi-device connection and control (page 22). Note: After you set up the TV Guide On Screen® system (Chapter 5), • Two HDMI (DVI) digital, high-definition multimedia interfaces (page 19). the program guide opens • Two sets of ColorStream® HD high-resolution component video inputs (pages 15 and 17). automatically by default when you turn on the TV. You can turn off • Dolby Digital* (page 20) and SRS WOW™ (page 86) audio technologies. the automatic program guide (page 40) and instead press the TV GUIDE • Digital Audio Out optical audio connection (page 20). button on the remote control to • CableClear® DNR digital picture noise reduction (page 80). manually open the program guide. • Double-window POP (page 76) and multi-window Favorites (page 78) features. ______________ In the United States, TV Guide and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. GEMSTAR-TV GUIDE INTERNATIONAL INC. AND/OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM AND CANNOT GUARANTEE SERVICE AVAILABILITY IN YOUR AREA. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE LIABLE FOR ANY DAMAGES IN CONNECTION WITH THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM. • This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 7 HM95_R1_007-08_061505 7 6/24/05, 8:46 PM

Chapter 1: Introduction Overview of steps for installing, setting up, and using your new TV Follow these steps to set up your TV and begin using its many exciting features. 1. Carefully read the important safety, installation, care, 8. See “Learning about the remote control” (page 26) for and service information on pages 2–5. Keep this an overview of the buttons on the remote control. manual for future reference. 9. Program the remote control to operate your other 2. Observe the following when choosing a location for device(s) (pages 28–34). the TV: 10. AFTER connecting all cables and devices, plug in the • Place the TV on the floor or on the optional TV stand listed in power cords for your TV and other devices. the “Specifications” section (page 106). 11. After you plug in the TV power cord, the green LED NOTICE OF POSSIBLE TV STAND INSTABILITY (on the TV front touchpad, to the left of the POWER button) DANGER: RISK OF SERIOUS PERSONAL INJURY will blink while the TV is booting until the remote control is OR DEATH! Use this TV only with the TOSHIBA TV usable. When the green LED stops blinking, press POWER to stand listed in the “Specifications” section (page 106). Use with other turn on the TV. stands may result in instability, causing possible injury or death. See “LED indications” on page 99. • Place the TV in a location where light does not reflect on the 12. See “Menu layout and navigation” for a quick overview screen. of navigating the TV’s menu system (pages 35–36). • Place the TV far enough from walls and other objects to allow 13. See Chapter 5 for details on setting up the TV Guide proper ventilation. Inadequate ventilation may cause On Screen® system (if available in your area). overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA 14. See Chapter 7 for details on using the TV Guide WARRANTY. On Screen® program guide (if available in your area). • Read “Installation” on pages 3–4. 15. Program channels into the TV’s channel memory (page 42). • Read “Important notes about your DLP™ TV” on page 5. 3. Do not plug in any power cords until AFTER you have 16. Set up the TheaterNet™ on-screen device control connected all cables and devices to your TV. feature (if applicable to your particular home theater system components) (page 45). 4. BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and controls (pages 9 17. For details on using the memory card JPEG picture and 10). viewer and MP3 audio player, see page 87. 5. Connect your other electronic device(s) to the TV 18. For details on using the TV’s features, see Chapter 8. (pages 12–25). 19. For help, refer to the Troubleshooting Guide (Chapter 6. Connect the G-LINK® cable (either one of the enclosed IR 10). blaster cables) from your VCR and/or Cable box (if applicable) to the G-LINK® terminal so you can use the TV Guide On Screen® 20. For technical specifications and warranty information, features (applies to VCRs and cable boxes only). See page 25. see Chapter 11. 7. Install the batteries in the remote control (page 28). 21. Enjoy your new TV! IMPORTANT NOTICE ABOUT “HOT LAMP RESTART” When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations: • When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes. • If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes. This is a property of DLP TV lamp technology and is NOT a sign of malfunction. If this occurs, the green LED on the TV front panel will blink (and the red LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If BOTH green and red LEDs are blinking at a one-second rate, you will need to turn the TV off and then on again to restart the lamp. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 8 HM95_R1_007-08_061505 8 6/24/05, 8:46 PM

2 Connecting your TV TV front touchpad and side panel controls and connections Front of TV Side panel TV/VIDEO EXIT CHANNEL VOLUME MENU POWER Remote sensor 1 Front touchpad* EXIT zyx • MENU (ENTER)** 3 4 5 GUIDE POWER 9 6 Side of TV { { VIDEO-3 IN Memory card !¡ slots !™ TV/VIDEO Channel zy Volume x • Green/Red LEDs 2 7 8 0 *Gently touch the printed keys on the touchpad. **The MENU button on the TV front touchpad functions as the ENTER button when a menu is on-screen. 1 Remote sensor (behind the screen) — Point the remote 8 VOLUME x • — When no menu is on-screen, these control toward this area of the TV screen. See “Remote buttons adjust the volume level. When a menu is on-screen, control effective range” on page 27. these buttons function as left/right menu navigation 2 TV/VIDEO — Repeatedly press to change the source you are buttons. viewing (ANT 1, ANT 2, VIDEO 1, VIDEO 2, VIDEO 3, 9 GUIDE — Press to access the TV Guide On Screen® HDMI 1, HDMI 2, ColorStream HD1, ColorStream program guide. (See page 53 for details on using the HD2). program guide.) 3 EXIT — Press to close an on-screen menu instantly. 0 Green and Red LEDs 4 ARROWS yzx • — When a menu is on-screen, these When the green LED lights solid (not blinking), it indicates buttons function as up/down/left/right menu navigation that recording is in progress. buttons. When the red LED lights solid (not blinking), it indicates 5 MENU (ENTER) — Press to access the menu system (see that the TV power cord is plugged in. page 35). When a menu is on-screen or the TV Guide See “LED indications” on page 99 for additional On Screen® program guide is open, the MENU button on information. the front touchpad functions as the ENTER button. !¡ VIDEO-3 — The side panel A/V connections are referred to 6 POWER — Press to turn the TV on and off. as “VIDEO 3” and include standard A/V connections plus Note: If the TV stops responding to the controls on the remote optional S-video. (The VIDEO 1 and VIDEO 2 A/V control or TV front panel and you cannot turn off the TV, press connections are on the TV’s back panel; see page 10. and hold the POWER button on the TV front panel for 5 or more seconds to reset the TV. !™ Memory card slots — Insert a memory card into one of the memory card slots to view JPEG files (such as photos) as 7 CHANNEL yz — When no menu is on-screen, these a “slide show” on your TV or listen to MP3 audio files (see buttons change the channel (programmed channels only; see page 87). page 42). When a menu is on-screen, these buttons function as up/down menu navigation buttons. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 9 HM95_R2_009-11_061505 9 6/27/05, 6:44 PM

Chapter 2: Connecting your TV TV back panel connections For an explanation of cable types, see page 11. 2 3 5 4 9 8 } } OUT OUT { 1 0 7 !¡ 6 !™ 1 ANT-1 (CABLE) IN and ANT-2 IN — Two inputs that 8 TheaterNet (IR) OUT — For controlling infrared ™ support analog (NTSC) and digital (ATSC) off-air antenna remote-controlled devices through the TV. You can connect signals and analog and digital (QAM) Cable TV signals. up to two devices with either one of the enclosed IR blaster Note: If you have an antenna only, connect it to ANT-1. If you have cables, and then control the devices using the TV’s IR pass- both cable TV and an antenna, connect the cable TV to ANT-1 and through or TheaterNet™ (on-screen device control) features. the antenna to ANT-2. See pages 21 and 45. 2 VIDEO 1 IN and VIDEO 2 IN — Two sets of standard 9 Standard Audio IN — For use when connecting a DVI (composite) video and standard audio inputs plus optional device with analog audio output to one of the HDMI S-video inputs for connecting devices with composite video inputs. See page 19. Also see item 10 below. or S-video output. 0 (2) HDMI™ IN 1 and 2 — Two High-Definition NOTE: Standard (composite) video and S-video cables carry Multimedia Interface inputs receive digital audio and only video information; separate audio cables are required for a uncompressed digital video from an HDMI device or complete connection. uncompressed digital video from a DVI device. See page 19. 3 ColorStream® HD-1 and ColorStream® HD-2 — Two sets NOTE: NEVER CONNECT THIS TV TO A PERSONAL of ColorStream® high-definition component video and COMPUTER (PC). This TV is not intended for use with a PC. standard stereo audio inputs for connecting devices with component video output, such as a Toshiba DVD player !¡ (2) IEEE1394 — Two bi-directional digital IEEE1394 with ColorStream®. See pages 15 and 17. ports for connecting multiple devices with compressed digital video. Because these ports are bi-directional, they can Note: Component video cables carry only video information; be used for playback and recording. You can control your separate audio cables are required for a complete connection. IEEE1394 devices using the TV’s TheaterNet on-screen 4 A/V OUT — Standard composite video and analog audio device control icons. See pages 21–24 and 46. outputs for connecting a VCR for editing and dubbing. See NOTE: page 18 for details. • IEEE1394 cable carries both audio and video information; 5 Variable Audio OUT — Standard analog audio outputs for separate audio cables are not required. connecting an analog amplifier with external speakers. See • NEVER CONNECT THIS TV TO A PERSONAL page 20. COMPUTER (PC). This TV is not intended for use with a PC. 6 Digital Audio OUT — Optical audio output in Dolby !™ CableCARD™ slot — For use with a digital security card Digital or PCM (pulse-code modulation) format for and digital cable TV service (provided by your local cable connecting an external Dolby Digital decoder, amplifier, operator) to view encrypted digital programming. See pages A/V receiver, or home theater system with optical audio 12 and 51. input. See page 20. 7 G-LINK® — For use with one of the enclosed IR blaster/ ___________ G-LINK® cables to enable the TV Guide On Screen® HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or recording features. See page 25. registered trademarks of HDMI Licensing LLC. CableCARD™ is a trademark of Cable Television Laboratories, Inc. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 10 HM95_R2_009-11_061505 10 6/27/05, 6:44 PM

Chapter 2: Connecting your TV Overview of cable types NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC). Coaxial (F-type) cable THIS TV IS NOT INTENDED FOR USE WITH A PC. Note: Two dual-wand IR blaster/G-LINK® cables are included with your TV. All other required cables, if not provided with your other devices, can be purchased at many electronics accessory suppliers. Standard A/V cables (red/white/yellow) ● Coaxial (F-type) cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT-1 and/or ANT-2 RF inputs on your TV. S-video cable ● Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with standard audio and standard (composite) video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. Component video cables (red/green/blue) ● S-video cable is for use with video devices with S-video output. Separate audio cables are required for a complete connection. Note: An S-video cable provides better picture performance than a composite video cable. If you connect an S-video cable, be sure to disconnect the standard (composite) video cable or the picture performance will be unacceptable. HDMI cable ● Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream ® is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are IEEE1394 cable (4-pin) required for a complete connection. Note: Component video cables provide better picture performance than a standard (composite) video or S-video cable. ● HDMI cable is for use with devices with HDMI (High-Definition Multimedia Interface) output. HDMI cable delivers digital audio and video in its native format. This cable carries both video and audio information; therefore, separate audio cables are Dual-wand IR blaster/ G-LINK® cable not required for a complete HDMI device connection. See page 19 for further details. (2 included) Note: HDMI cable provides better picture performance than a standard (composite) video or S-video cable. ● IEEE1394 cable is for use with video devices with compressed digital video output Optical audio cable that meet CEA specifications for IEEE1394. This cable carries both video and audio information; therefore, no separate audio cables are required for a complete connection. See pages 22–24. Note: Although your TV includes both HDMI Note: and IEEE1394 connections, it may not • The transmission capability of IEEE1394 cable used with this TV must be S400 operate with another device you have that (400 Mbps maximum). includes such a connection. For example, the • IEEE1394 cable provides better picture performance than a standard (composite) IEEE1394 ports are not intended to operate video or S-video cable. with current model Mini DV camcorders, and ● Dual-wand IR blaster/G-LINK® cable is for use with video devices with IR (infrared) the HDMI input is not intended for remote control. Two of these cables are included with your TV. One is for connection connection to a computer. Copyright to the G-LINK® terminal (page 25) to enable TV Guide On Screen ® recording features protection requirements may also prohibit or (Chapters 5 and 7). The other can be used with the TV’s IR pass-through feature (page limit connectivity. See page 19 for details about the HDMI input. See pages 22–24 for 21) and TheaterNet™ on-screen device control feature (page 45). details about the IEEE1394 ports. Note: The two IR blaster/G-LINK ® cables included with your TV have specific characteristics that allow them to work properly with this TV’s IR OUT and G-LINK ® ports. Never use other aftermarket IR blaster or G-LINK ® cables with this TV. Other cables may not function properly and can cause damage. THIS TYPE OF DAMAGE IS NOT COVERED BY YOUR TOSHIBA WARRANTY. ● Optical audio cable is for connecting receivers with Dolby Digital or PCM (pulse-code modulation) optical audio input to the TV’s DIGITAL AUDIO OUT terminal. See page 20. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 11 HM95_R2_009-11_061505 11 6/27/05, 6:44 PM

Chapter 2: Connecting your TV About the connection illustrations You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output terminals on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s owner’s manual. Connecting a digital CableCARD™ This digital television is capable of receiving analog basic, digital  To view encrypted digital channels: basic, and digital premium cable television programming by direct connection to a cable system providing such 1. Connect your digital Cable TV cable to ANT-1. programming. 2. With the front of the CableCARD™ facing up, insert it into A security card (such as a digital CableCARD™), provided by the CableCARD™ slot on the back of the TV (see your cable operator, is required to view encrypted digital illustration below left). programming. 3. After the CableCARD™ is inserted, a CableCARD™ option Certain advanced and interactive digital cable services (such as appears in the Applications menu, with informational video-on-demand, a cable operator’s enhanced program guide, screens provided by your digital CableCARD™ service. See and data-enhanced television services) will not work with the page 51 for additional information. use of a CableCARD™ and may require the use of a separate set- top box from your cable operator. CableCard Connected -- Acquiring channel information. For more information, call your local cable operator. CableCard services will only operate Applications TV Guide On Screen IP Service You will need: with cable signal connected to Antenna 1. Audio Player Conditional Access Picture Viewer CableCARD(tm) Status  one digital CableCARD™ (contact your cable operator) Digital CC/Audio Selector CableCARD Network Setup CableCARD(tm) Pairing  digital cable subscription service (contact your cable operator) Navigate Select CH RTN Back EXIT Exit TV back panel OUT Note: • Always use the EJECT button to remove the CableCARD™. Never remove the CableCARD™ carelessly. • Never insert any object or card (including, without limitation, a PCMCIA card) other than a CableCARD™ into the CableCARD™ slot. • Always make sure the CableCARD™ is facing the correct direction. • Connect the cable for your digital cable TV service to ANT-1 only. • When using a CableCARD™, channel programming is unnecessary because the CableCARD™ automatically loads the cable channel list into the TV’s channel memory (page 42). • The CableCARD™ may take up to 5 minutes to “pair” with the TV and download channel information. CableCARD™ information and channels will not be available until this process is completed. From digital Cable service CableCARD™ technology, like all new and emerging technology, may (connect to ANT 1 only) from time to time experience compatibility issues due to the different ways in which television manufacturers and cable system operators implement the CableCARD™ specifications. Most issues can be easily resolved. If you experience any performance-related CableCARD™ This cable should be connected to ANT 1 terminal directly. If you connect issues with your Toshiba television, please contact Toshiba the cable via a VCR, the TV may not receive the signals correctly. Consumer Solutions by calling (800) 631-3811 or by visiting http://www.tacp.com/customersupport/contact.asp. ________ CableCARD is a trademark of Cable Television Laboratories, Inc. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 12 HM95_R1_012-25_061505 12 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a VCR and antenna or Cable TV (no Cable box) You will need:  one signal splitter From Cable TV or antenna  three coaxial cables Signal splitter IN  two sets of standard A/V cables OUT OUT • For better picture performance, if your VCR has S-video, use an S-video cable (plus the audio cables) instead of the standard Stereo VCR video cable. However, do not connect both types of video cables VIDEO AUDIO IN from ANT L R to VIDEO 1 (or VIDEO 2) at the same time or the picture CH 3 IN performance will be unacceptable. OUT to TV CH 4 OUT • If you have a mono VCR, connect L/MONO on the TV to your L R VCR’s audio out terminal using the white audio cable only. TV  To view the antenna or Cable signal: OUT Select the ANT 1 video input source on the TV.*  To view the VCR: Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*  To use the TV Guide On Screen ® recording features: ® 1. Connect the G-LINK cable according to the instructions on page 25. 2. Make sure the VCR is connected to the A/V OUT terminals on the TV (see illustration). 3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the Note: The VIDEO/AUDIO OUT terminals output signals from the VCR. ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the 4. See Chapter 5 for details on setting up the TV Guide appropriate input mode is selected. On Screen® system. The unauthorized recording, use, distribution, or revision of television 5. See Chapter 7 for details on using the TV Guide programs, videotapes, DVDs, and other materials is prohibited under the On Screen® system. Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. Connecting a camcorder You will need:  one set of standard A/V cables Camcorder • For better picture performance, if your camcorder has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect both an S-video cable and a standard video cable to VIDEO 3 at the same time or the picture performance will be unacceptable. VIDEO AUDIO L OUT  To view the camcorder video: R Select the VIDEO 3 video input source on the TV.* ______________ * To select the video input source, press INPUT on the remote control (see page 67). To program the TV remote control to operate other devices, see Chapter 3. VIDEO 3 inputs on TV right side panel Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 13 HM95_R1_012-25_061505 13 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a VCR and Cable box You will need: From Cable TV  one signal splitter IN  five coaxial cables Cable box IN Signal splitter OUT CH 3  two sets of standard A/V cables OUT CH 4 OUT • For better picture performance from your VCR: If your VCR has Stereo VCR S-video, connect an S-video cable (plus the audio cables) instead VIDEO AUDIO IN from ANT L R of the standard video cable. Do not connect an S-video cable and CH 3 IN CH 4 a standard video cable to VIDEO 1 (or VIDEO 2) at the same time OUT to TV OUT or the picture performance will be unacceptable. L R • If you have a mono VCR, connect L/MONO on the TV to your TV VCR’s audio out terminal using the white audio cable only. OUT • When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.  To view basic Cable channels and use the TV’s features: Select the ANT 1 video input source on the TV.* Use the TV controls (front panel or remote control) to change channels and access the TV’s features.  To view basic and premium Cable channels: Turn OFF the VCR. Select the ANT 2 video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the Cable box output is set to). Use the Cable box controls to change channels.  To view the VCR: Turn ON the VCR. Select the VIDEO 1 video input source on the TV.* Note: The VIDEO/AUDIO OUT terminals output signals from the Note: A VIDEO 1 connection with an S-Video cable (instead ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the of a standard video cable) will provide better picture appropriate input mode is selected. performance (as mentioned in the first bulleted item at the top of this page). _____________  To enable the TV Guide On Screen system to work ® * To select the video input source, press INPUT on the remote control with your cable box and to use the TV Guide (see page 67). To program the TV remote control to operate other On Screen® recording features: devices, see Chapter 3. 1. Connect the G-LINK® cable according to the instructions on page 25. The unauthorized recording, use, distribution, or revision of television 2. Make sure the VCR is connected to the A/V OUT programs, videotapes, DVDs, and other materials is prohibited under the terminals on the TV (see illustration). Copyright Laws of the United States and other countries, and may subject 3. Set the VCR to the appropriate line input (refer to your you to civil and criminal liability. VCR owner’s manual for details), and then turn OFF the VCR. 4. See Chapter 5 for details on setting up the TV Guide On Screen® system. 5. See Chapter 7 for details on using the TV Guide On Screen® system. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 14 HM95_R1_012-25_061505 14 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a VCR and satellite receiver You will need: From antenna  one signal splitter IN Signal splitter  four coaxial cables OUT  one set of component video cables (if your OUT satellite receiver does not have component Stereo VCR video, connect the standard A/V cables only) VIDEO AUDIO  one pair of standard audio cables IN from ANT L R CH 3 IN CH 4  two sets of standard A/V cables OUT to TV OUT L R • For better picture performance, if your satellite receiver and VCR have S-video, connect S-video TV cables (plus the audio cables) instead of the standard OUT video cables. Do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable. • If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s AUDIO OUT terminal using the white audio cable only.  To view satellite programs using the component video connections: Select the ColorStream HD-1 video input source on the TV.* From satellite dish  To view satellite programs using the standard Satellite receiver video connections or to record satellite programs: AUDIO Turn on all three devices. Set the VCR to the appropriate Y PB PR LOUT L line input (refer to your VCR owner’s manual for details). Satellite IN R R Select the VIDEO 2 video input source on the TV.* S-VIDEO OUT COMPONENT VIDEO VIDEO OUT  To view the VCR or view and record antenna channels: Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, Turn ON the VCR. Tune the VCR to the channel you want ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate to watch. Select the VIDEO 1 video input source on the input mode is selected. TV.* _____________ * To select the video input source, press INPUT on the remote control  To use the TV Guide On Screen recording features:® ® 1. Connect the G-LINK cable according to the instructions (see page 67). To program the TV remote control to operate other devices, see Chapter 3. on page 25. 2. Make sure the VCR is connected to the A/V OUT The unauthorized recording, use, distribution, or revision of television terminals on the TV (see illustration). programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject 3. Set the VCR to the appropriate line input (refer to your you to civil and criminal liability. VCR owner’s manual for details), and then turn OFF the VCR. 4. See Chapter 5 for details on setting up the TV Guide On Screen® system. 5. See Chapter 7 for details on using the TV Guide On Screen® system. Note: The TV Guide On Screen® system does not receive program listings from or for any satellite service. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 15 HM95_R1_012-25_061505 15 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a DVD player with S-video, a VCR, and a Cable box You will need: From antenna or Cable TV  one signal splitter IN Cable box Signal splitter  five coaxial cables CH 3 IN OUT  two sets of standard A/V cables OUT CH 4 OUT Stereo VCR Note: If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s audio out terminal using the white IN from ANT VIDEO AUDIO L R audio cable only. CH 3 CH 4 IN  one S-video cable OUT to TV OUT  one pair of standard audio cables L R TV Note: OUT • If your DVD player does not have S-video, use a standard video cable instead. Do not connect an S-video cable and a standard video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable. • If your DVD player has component video, see page 17. • Do not connect the DVD player and VCR to the same set of A/V inputs on the TV. (See the illustration, which shows the VCR connected to VIDEO 1 on the TV, and the DVD player connected to VIDEO 2.)  To view basic channels and access the TV’s features: Select the ANT 1 video input source.* Use the TV AUDIO controls to change channels and access the TV’s features. OUT L  To view premium Cable channels: S-VIDEO OUT VIDEO OUT R Turn OFF the VCR. Select the ANT 2 video input DVD player with S-video source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the Cable box output is set to). Use the Cable box controls to change channels. Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, Note: When you use a Cable box, you may not be able to ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input use the remote control to program or access certain mode is selected. features on the TV.  To view the DVD player: Turn ON the DVD player. Select the VIDEO 2 video  To enable the TV Guide On Screen ® system to work with input source on the TV.* your cable box and to use the TV Guide On Screen® recording features:  To view the VCR: 1. Connect the G-LINK® cable according to the instructions on Turn ON the VCR. Select the VIDEO 1 video input page 25. source on the TV.* 2. Make sure the VCR is connected to the A/V OUT terminals _____________ on the TV (see illustration). * To select the video input source, press INPUT on the remote control 3. Set the VCR to the appropriate line input (refer to your VCR (see page 67). To program the TV remote control to operate other owner’s manual for details), and then turn OFF the VCR. devices, see Chapter 3. 4. See Chapter 5 for details on setting up the TV Guide The unauthorized recording, use, distribution, or revision of On Screen® system. television programs, videotapes, DVDs, and other materials is 5. See Chapter 7 for details on using the TV Guide On Screen® prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. system. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 16 HM95_R1_012-25_061505 16 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a DVD player with ColorStream® (component video) and a VCR Your TV has ColorStream® (component video) inputs. From antenna or Cable You will need: Signal splitter IN  one signal splitter OUT OUT  three coaxial cables Stereo VCR  two sets of standard A/V cables VIDEO AUDIO • For better picture performance, if your VCR has S-video, use an IN from ANT L R CH 3 S-video cable (plus the audio cables) instead of the standard CH 4 IN OUT to TV video cable. However, do not connect both types of video cable to OUT VIDEO 1 (or VIDEO 2) at the same time or the picture L R performance will be unacceptable. TV • If you have a mono VCR, connect L/MONO on the TV OUT (VIDEO 1) to your VCR’s audio out terminal using the white audio cable only.  one pair of standard audio cables  one set of component video cables • You can connect the component video cables (plus audio cables) from the DVD player to either set of ColorStream terminals on the TV (HD-1 or HD-2). The ColorStream HD-1 and HD-2 terminals can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. A 1080i signal will provide the best picture performance. • If your DVD player does not have component video, see page 16. If your DVD player has HDMI video, see page 19.  To view antenna or Cable channels: AUDIO OUT Y PB PR L Select the ANT 1 video input source on the TV.* S-VIDEO COMPONENT VIDEO VIDEO R OUT OUT  To view the DVD player: DVD player with component video Turn ON the DVD player. Select the ColorStream HD-1 video input source on the TV.*  To view the VCR: Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate Turn ON the VCR. Select the VIDEO 1 video input input mode is selected. source on the TV.*  To record a TV program while watching a DVD: Turn ON the VCR. Tune the VCR to the channel to  To use the TV Guide On Screen ® recording features: record. Select the ColorStream HD-1 video input source ® 1. Connect the G-LINK cable according to the instructions on the TV* to view the DVD. on page 25. _____________ 2. Make sure the VCR is connected to the A/V OUT * To select the video input source, press INPUT on the remote control terminals on the TV (see illustration). (see page 67). To program the TV remote control to operate other devices, see Chapter 3. 3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the The unauthorized recording, use, distribution, or revision of television VCR. programs, videotapes, DVDs, and other materials is prohibited under the 4. See Chapter 5 for details on setting up the TV Guide Copyright Laws of the United States and other countries, and may subject On Screen® system. you to civil and criminal liability. 5. See Chapter 7 for details on using the TV Guide On Screen® system. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 17 HM95_R1_012-25_061505 17 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting two VCRs You will need: From antenna or Cable  one signal splitter IN ** Signal splitter  three coaxial cables OUT  two sets of standard A/V cables OUT • For better picture performance, if VCR 1 has S-video, use VCR1 (plays) an S-video cable (plus the audio cables) instead of the VIDEO AUDIO standard video cable. However, do not connect both types IN from ANT L R CH 3 IN of video cable to VIDEO 1 (or VIDEO 2) at the same time CH 4 OUT to TV or the picture performance will be unacceptable. OUT L R • If VCR 1 has mono audio, connect L/MONO on the TV (VIDEO 1) to the audio out terminal on VCR 1 using the white audio cable TV only. OUT • Do not connect the same VCR to the output and input terminals on a the TV at the same time.  To view the antenna or Cable signal: Select the ANT-1 video input source on the TV.* b  To view VCR 1: Turn ON VCR 1. Select the VIDEO 1 video input source on the TV.*  To dub or edit from VCR 1 to VCR 2: Turn ON both VCRs. Set VCR 2 to the appropriate line VCR2 (records) input (refer to your VCR owner’s manual for details). Select VIDEO AUDIO the VIDEO 1 video input source on the TV.* IN from ANT CH 3 L R IN CH 4 Note: OUT OUT to TV L R • If you have a Cable box, connect the Cable box and splitter to VCR1 L R as shown on page 14. • The VIDEO OUT signal incorporates Macrovision® copyright a The VIDEO OUT terminal does not output the POP picture. protection technology, which may prevent you from recording certain copy-restricted video materials.*** b When POP mode is active, the AUDIO OUT terminals output the sound of the active window (main or POP). For additional information, see “Notes about recording” on page 76. _________________________________________________________________ Note: The VIDEO/AUDIO OUT terminals output signals from the * To select the video input source, press INPUT on the remote control ANT 1, ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when (see page 67). To program the TV remote control to operate other the appropriate input mode is selected. devices, see Chapter 3. ** Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the TV.  To use the TV Guide On Screen ® recording features: ® 1. Connect the G-LINK cable according to the instructions *** This product incorporates copyright protection technology that is protected by on page 25. U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other 2. Make sure the VCR is connected to the A/V OUT limited pay-per-view uses only, unless otherwise authorized by Macrovision. terminals on the TV (see illustration). Reverse engineering or disassembly is prohibited. Macrovision is a registered trademark of Macrovision Corporation. 3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the The unauthorized recording, use, distribution, or revision of television VCR. programs, videotapes, DVDs, and other materials is prohibited under the 4. See Chapter 5 for details on setting up the TV Guide Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. On Screen® system. 5. See Chapter 7 for details on using the TV Guide On Screen® system. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 18 HM95_R1_012-25_061505 18 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting an HDMI™ or a DVI device to the HDMI input The HDMI[1] input on your TV receives digital audio and __________________________________________________________________ uncompressed digital video from an HDMI device or [1] HDMI = High-Definition Multimedia Interface. uncompressed digital video from a DVI[2] device. [2] DVI = Digital Video Interface. This input is designed to accept HDCP [3] program material in [3] HDCP = High-bandwidth Digital Content Protection. digital form from EIA/CEA-861/861B–compliant [4] consumer [4] EIA/CEA-861/861B compliance covers the transmission of electronic devices (such as a set-top box or DVD player with uncompressed digital video with high-bandwidth digital content HDMI or DVI output). protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that The HDMI input is designed for best performance with 720p some devices may not operate properly with the TV. signals but will also accept and display 1080i, 480i, and 480p signals. NOTE: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these NOTE: NEVER CONNECT THIS TV procedures: TO A PERSONAL COMPUTER (PC). • When turning on your electronic components, turn on THIS TV IS NOT INTENDED FOR USE WITH A PC. the TV first, and then the HDMI or DVI device. • When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV. To connect an HDMI device, you will need: • one HDMI cable (type A connector) per HDMI device To connect a DVI device, you will need: For proper operation, it is recommended that you use as • one HDMI-to-DVI adapter cable (HDMI type A short an HDMI cable as possible. You should not connector) per DVI device encounter difficulty if you use an HDMI cable shorter than For proper operation, the length of an HDMI-to-DVI adapter 16.4 ft (5m). cable should not exceed 9.8 ft (3m). The recommended length is HDMI cable transfers both video and audio. Separate 6.6 ft (2m). analog audio cables are not required (see illustration • one pair of standard analog audio cables per DVI below). Some CDVs (video CDs) may not output digital device audio signals. In that case, you may hear sound by connecting analog audio cables. An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration See “Setting the HDMI audio mode” on page 50. below). See “Setting the HDMI audio mode” on page 50. HDMI device DVI device HDMI OUT DVI/HDCP VIDEO AUDIO VIDEO AUDIO OUT L R IN L R IN L R OUT L R OUT R TV TV OUT OUT ___________ HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 19 HM95_R1_012-25_061505 19 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Connecting a digital audio system Dolby Digital decoder or The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby* other digital audio system Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital Optical LINE IN decoder or other external audio system with optical audio input. L R Audio IN You will need: TV  one optical audio cable (Use an optical audio cable that has the larger “TOSlink” connector and not the smaller “mini-optical” connector.) To control the audio: Turn on the TV and the digital audio device. Press MENU on the TV’s remote control and open the AUDIO menu. Audio Audio Settings Highlight Audio Setup and Advanced Audio Settings Audio Setup press ENTER. In the Optical Output Format field, select either Dolby Digital or PCM, depending on your device (see “Selecting the optical Note: audio output format” on page 86). • Some audio systems may not be compatible with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard Audio Setup optical out signals may not work properly, creating a high noise level MTS Stereo that may damage speakers or headphones. THIS DAMAGE IS NOT Language English COVERED BY YOUR WARRANTY. Speakers On • The DIGITAL AUDIO OUT terminal outputs signals only when receiving Optical Output Format Dolby Digital digital broadcasts with the TV in single-window mode. Reset Done • The DIGITAL AUDIO OUT terminal may not output some digital audio sources because of copy restrictions. Turn off the TV’s built-in speakers in the same Audio Setup ___________ menu (above). Also see “Turning off the built-in speakers” on * Manufactured under license from Dolby Laboratories. “Dolby” and page 86. the double-D symbol are trademarks of Dolby Laboratories. Connecting an analog audio system This connection allows you to use external speakers with an Analog audio amplifier external audio amplifier to adjust the sound level. You will need: LINE IN L R  one pair of standard audio cables To control the audio: Turn on the TV and the stereo amplifier. TV Turn off the TV’s built-in speakers (see “Turning off the built-in OUT speakers” on page 86). Note: To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set to a reasonable listening level. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 20 HM95_R1_012-25_061505 20 6/24/05, 9:12 PM

Chapter 2: Connecting your TV Controlling infrared remote-controlled devices through the TV (IR pass-through) Front of IR-controlled DVD player (for example) You can use the TV’s IR OUT terminal (infrared pass-through) to remotely operate (through the TV) many infrared remote- controlled devices (such as a Toshiba infrared remote-controlled VCR or DVD player) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely. Front of IR-controlled audio device (for example) You will need:  one dual-wand IR blaster cable (included with your TV)  other audio/video cables as required to connect the device(s) to the TV (see pages 13–20) Infrared sensor To connect the IR blaster cable: 1. Locate the infrared sensor on the front of your device. This IR blaster cable wand (approx. 1 inch from device) sensor is marked on some devices.* Back of TV 2. Align one of the IR blaster cable’s wands about 1 inch away from the infrared sensor on the front of the device and OUT attach it using double-sided mounting tape. If you have a second device, attach the second wand in a similar manner. (See illustration at right.) Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the TV. 3. Plug the IR blaster cable’s plug into one of the TV’s TheaterNet OUT terminals. To control the device(s): Point the TV remote control (programmed to operate the device; see Chapter 3) or the device’s remote control at the front of the TV and press the button for the desired function. The signal TV/VIDEO EXIT CHANNEL VOLUME MENU POWER passes from the remote control through the TV to the device via the IR blaster cable. TheaterNet™ on-screen device control Note: • If you use the device’s remote For additional control options control to operate the device, you for your home theater system, also will need to use the TV’s remote control to operate the TV. set up the TheaterNet on- • For additional control options, see “TheaterNet on-screen device screen device control feature. Toshiba Video 3 control” at right. You can use this feature to ENTER control many IR remote- TOP MENU EXIT * If you cannot locate the device’s infrared sensor: controlled devices and TV/VIDEO EXIT CHANNEL VOLUME MENU POWER 1. Turn OFF the device. IEEE1394 devices using the 2. Starting at the lower left corner of the device, place the end of the on-screen control icons. device’s remote control (with the infrared emitter) so it touches the See pages 45–49 for details on front of the device and press POWER. (Do not use the TV’s remote setting up and using TheaterNet. control for this step.) See pages 22–24 for details on 3. If the device turns on, the point at which the remote control touched connecting IEEE1394 devices. the device is the location of the sensor. 4. If the device does not turn on, move the remote control slightly to the Note: The TheaterNet on-screen icons are the only device functions right and press POWER again. available when the icons are on-screen. To access other device 5. Repeat step 4 until you locate the device’s infrared sensor. functions, close the TheaterNet icon window. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 21 HM95_R1_012-25_061505 21 6/24/05, 9:13 PM

Chapter 2: Connecting your TV Connecting IEEE1394 video devices You can use the two bi-directional IEEE1394 ports on the back NOTE: NEVER CONNECT THIS TV of your TV to connect digital video devices that meet CEA TO A PERSONAL COMPUTER (PC). specifications for IEEE1394. THIS TV IS NOT INTENDED FOR USE WITH A PC. Because these ports are bi-directional, they can be used for both playback and recording. • Because IEEE1394 is an evolving technology, it is possible that some Supported signals or all of the connectivity features of a device you connect to the TV The IEEE1394 ports support only the signals listed below. Even through the IEEE1394 ports may not operate. You should confirm though incompatible video, audio, and digital control signals that the devices you want to use with the IEEE1394 ports will operate with those ports. cannot be decoded by the TV, these signals may be passed through the IEEE1394 cable to other compatible devices. • This TV does not support all possible IEEE1394 signal types. For Incompatible devices may not appear in the TheaterNet™ menu. information on signals supported by the IEEE1394 ports, see “Supported signals” at right. • MPEG-2 digital video signals • IEEE1394 cable carries both audio and video information; Other digital video signals—such as DV video—are separate audio cables are not required. incompatible and must be decoded by the source device and sent to the TV as analog video (composite or S-video). You will need:  one (or two) IEEE1394 cables • Dolby Digital and MPEG digital audio signals Note: The transmission capability of IEEE1394 cable used with this Other digital audio signals (such as DPM, MP3, and DTS) are TV must be S400 (400 Mbps maximum). incompatible and cannot be decoded by the TV.  additional A/V cables if your device is analog-compatible • EIA-775 and AV/C digital control (see “Using analog-compatible IEEE1394 devices” below). Your TV can serve as the control center for many devices TV back panel that are compatible with EIA-775 or AV/C IEEE1394 control standards (described below). The TV cannot control IEEE1394 devices that use any other control standards. – EIA-775 digital control allows tuning devices (such as Cable boxes) to send simple graphics; however, this standard does not allow the TV to control the Cable box through IEEE1394. – AV/C (audio/video control) provides basic control (such } as power, play, stop rewind, fast-forward, pause, and record), as applicable to the specific device. Two bi-directional IEEE1394 ports From IEEE1394 Using TheaterNet™ on-screen device devices (such as AVHD or D-VHS) control Using analog-compatible IEEE1394 You can use the TheaterNet feature to control some IEEE1394 devices devices using on-screen control icons. See page 45 for details on setting up and using the TheaterNet feature. Some digital IEEE1394 devices are compatible with analog Note: If the TheaterNet feature does not control your signals. For example, some D-VHS VCRs can record and play IEEE1394 device, you can either use the device’s remote VHS or S-VHS format videos. Such devices allow you to play control or try using IR pass-through with the TV’s remote analog tapes that you rented or recorded, or record analog control (page 21). programs from antenna or Cable TV systems. To use the IEEE1394 device’s analog features, you need to connect the device to the TV using standard A/V cables (or S-video plus audio cables) in addition to connecting the IEEE1394 cable. Note: If you have an IEEE1394 device connected to both digital and analog inputs on the TV, the TV automatically switches between digital and analog modes, as needed, when the initial device access is initiated using the TheaterNet button. See page 45 for details on using the TheaterNet feature. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 22 HM95_R1_012-25_061505 22 6/24/05, 9:13 PM

Chapter 2: Connecting your TV Connecting IEEE1394 video devices (continued) Connecting an AVHD (external hard IEEE1394 device initialization drive) or D-VHS digital recorder When you connect a new IEEE1394 device to the TV and turn it on, the device immediately announces its presence to the TV You can connect an IEEE1394 compatible D-VHS or AVHD (and other networked IEEE1394 devices, if any), and the (audio/video hard drive) digital recorder (such as Toshiba’s following device initialization screen automatically appears. Symbio™ AVHD Recorder) to record high definition and Note: With some devices, it may take up to one minute for this standard definition material from either tuner and control live screen to appear. TV (pause, rewind, etc.). 1. If you also connected your IEEE1394 device to an analog When you connect a D-VHS or AVHD device to the TV: input, use the yzx • buttons to select the input in the • The remote control keys (LIVE, REW, PAUSE, PLAY, FF, etc.) are ANALOG INPUT USED field; otherwise, leave it set to automatically activated to allow control of live TV. “None.” (See “Using analog-compatible IEEE1394 devices” • The TV Guide On Screen® system is automatically configured to on page 22.) allow recording to the device.* See Chapters 5 and 7 for details. 2. If you want to label the device, highlight Edit Label and Also see page 50 for details on setting the AVHD device skip time. press ENTER. • Some programs may not be recorded due to copy protection New IEEE1394 Device Initilization restrictions. Manufacturer TOSHIBA Device Type AVHD Custom Label This TV is compatible with the new Toshiba TM Edit Label Done 3. Press the yzx • buttons to select a character for the first Audio/Video Hard Drive Recorder! space and then press ENTER. Toshiba’s Symbio™ AVHD Recorder is designed specifically for high definition television (HDTV) and offers control over digital 4. Repeat step 3 to enter the rest of the characters. video recording and playback. 5. Highlight Done and press ENTER to save the information. Think of it as a “tapeless VCR” for digital television. You can pause, IEEE1394 Device Label Edit rewind, or use instant replay, so you’ll never miss a thing! MY DEVICE_ Symbio also offers one-touch recording* of both standard and A B C D E F G High Definition programs through the no-fee TV Guide H I J K L M N O P Q R S T U On Screen® interactive program guide built in to this TV. V W X Y Z 0 1 2 3 4 5 6 7 8 9 SPC CLR BS NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC). Done Exit THIS TV IS NOT INTENDED FOR USE WITH A PC. Note: The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the • The TV may not recognize incompatible or non-A/V IEEE1394 Copyright Laws of the United States and other countries, and may subject devices; however, these devices may still be available to other you to civil and criminal liability. compatible IEEE1394 devices on the network. • You may be able to use the TV’s remote control to operate some *Note: To enjoy the full benefits of your Symbio AVHD Recorder, you must compatible IEEE1394 devices. You must first program the first set up the TV Guide On Screen® system (see Chapter 5). Full Symbio remote control to recognize the device (see Chapter 3). If you AVHD Recorder benefits, including Intelligent One Touch recording, will not have an IEEE1394 Cable box or satellite receiver, you may need be available unless the TV Guide On Screen® system is fully operational. to use the remote control that came with the device. However, when the TV Guide On Screen® system is not fully operational, manual recording is available as long as the TV Guide On Screen® system • Toshiba is not liable for the operation of any IEEE1394 device has acquired the necessary date and time data. If you experience any other than the Toshiba Symbio AVHD recorder. issues with your Symbio AVHD Recorder, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or visiting http://www.tacp.com/customersupport/contact.asp. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 23 HM95_R1_012-25_061505 23 6/24/05, 9:13 PM

Chapter 2: Connecting your TV Connecting IEEE1394 video devices (continued) IEEE1394 device management Important information regarding IEEE1394 The IEEE1394 device information is saved in the TV’s memory. device interconnection You can edit this device information (for example, edit the • Never loop the last device in the chain back to the TV. device name, change the analog input information, or delete the If the device chain is looped, the TV may not work properly with the device information from the TV’s memory if you no longer use other devices in the chain. that device). • Always place devices with the slowest communication To edit the IEEE1394 device information: speed at the end of each chain. If a device with a slower communication speed is placed ahead of a faster device in the 1. Press MENU and open the Setup menu. chain, the signal from the slower device will interfere with the signal 2. Highlight Installation and press ENTER. (A new set of from the faster device. To determine the communication speed of Installation menu icons will appear on-screen, as shown in an IEEE1394 device, look for an “S” number near the device’s step 3 below). IEEE1394 connector. The higher the “S” number, the faster the device. If your device is not marked with an “S” number, look in the device’s user manual or call the device manufacturer’s technical Setup support number. Installation Sleep Timer • If your IEEE1394 device has a two-position power On/Off Timer switch, always place the device at the end of the chain HDMI 1 Audio Auto HDMI 2 Audio Auto and turn ON the power switch when any device is used. Slide Show Interval 2 Sec If the power switch is OFF, it will interfere with signals from devices AVHD Skip Time 15 min behind it in the chain. Navigate Select CH RTN Back EXIT Exit • The maximum length for an IEEE1394 cable between 3. Open the Devices menu, highlight IEEE1394 Devices, and each device is 15 feet. press ENTER. • This TV is an IEEE1394A device. The IEEE1394B protocol is faster and intended to allow for longer distances between devices and multi-room systems. IEEE1394A–to–IEEE1394B converters Devices (available at some electronics suppliers) may allow compatibility of IEEE1394 Devices IEEE1394B devices with your existing IEEE1394A devices. TheaterNet Devices • The transmission capability of IEEE1394 cable used with this TV must be S400 (400 Mbps maximum). Navigate Select CH RTN Back EXIT Exit 4. Highlight the device you want to edit and press ENTER. IEEE1394 Device Management Brand Type Label Analog Input Used Connected TOSHIBA AVHD MY DEVICE None No Reset Done 5. Follow the on-screen prompts to modify the device information. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 24 HM95_R1_012-25_061505 24 6/24/05, 9:13 PM

Chapter 2: Connecting your TV G-LINK® connection • This connection is necessary for the TV Guide On Screen® system to work with your cable box to receive program listings and to enable the TV Guide On Screen® recording features with your VCR. • This connection is not necessary for AVHD or D-VHS recording devices. See pages 23 and 50 for further details. After you connect your devices to the TV, you will need to connect the G-LINK ® cable (either of the dual-wand IR blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK® terminal on the TV. Note: TV Guide On Screen® program data is available through the ANT-1 and ANT-2 antenna inputs and also through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen® program data is not available through any other inputs on this TV. See the connection information on pages 13–25. The G-LINK® connection is necessary to enable the following features of your TV Guide On Screen® system: • If you have a Cable box, you need to connect the G-LINK® cable from the Cable box to the G-LINK® terminal to receive the TV Guide On Screen® program listings for your Cable service. • If you have a VCR, you need to connect the G-LINK® cable from the VCR to the G-LINK® terminal to use the TV Guide On Screen® recording features. To connect to the G-LINK® terminal: Front of Cable box 1. Locate the infrared sensor on the front of your VCR or Cable box. The sensor is marked on some devices.* 2. Align one of the G-LINK® (IR blaster) cable’s wands about 1 inch away from the infrared sensor on the front of the VCR and attach it using double-sided mounting tape. Front of VCR If you have a Cable box, attach the other wand in a similar manner. (See illustration at right.) Note: If you do not have a Cable box, coil the second wand with a rubber band and leave it behind the TV. Infrared 3. Plug the G-LINK® (IR blaster) cable’s plug into the TV’s sensor G-LINK® terminal. G-LINK® (IR blaster) cable wand For details on setting up the TV Guide On Screen® system: (approx. 1 inch from device) See Chapter 5. Back of TV OUT For details on using the TV Guide On Screen® interactive program guide: See Chapter 7. * If you cannot locate the device’s infrared sensor: 1. Turn OFF the device. 2. Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.) 3. If the device turns on, the point at which the remote control touched the device is the location of the sensor. 4. If the device does not turn on, move the remote control slightly to the right and press POWER again. 5. Repeat step 4 until you locate the device’s infrared sensor. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 25 HM95_R1_012-25_061505 25 6/24/05, 9:13 PM

3 Using the remote control Learning about the remote control The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the remote control functional key chart on pages 29–30. For a list of the buttons that operate the TV Guide On Screen® system, see page 54. POWER turns the TV on and off. Note: The Quick Restart setting will affect the amount of time it takes for the picture to appear when you turn on the TV. See page 51 for details. SLEEP accesses the sleep timer (page 91). LIGHT The first press of the LIGHT button lights the keypad and turns on the Illumination mode. With the Illumination mode on, pressing any key lights the keypad for 5 seconds (10 seconds if you’re in programming mode). Subsequent presses of the LIGHT button toggle between turning the Illumination mode on and off. Channel Numbers (0–9, –/100) directly tune channels. The “–” button is used to tune digital channels (page 71) or to display the favorite channel list (page 44). INPUT selects the video input source (page 67). MODE cycles through the six remote control device modes: TV, CBL/SAT, VCR/PVR, DVD, AUDIO1, and AUDIO2. The mode indicator light will remain lit for a few seconds (page 28). PIC SIZE cycles through the five pictures sizes: Natural, TheaterWide 1/2/ 3, and Full (page 72). TheaterNet™ DEVICE displays a list of available TheaterNet devices (page 45). TheaterNet™ CTRL accesses the on-screen IR device control icons (page 46). MENU accesses the main TV menu system (pages 35 and 36) or opens a menu in the TV Guide On Screen® system (Chapter 7). TV GUIDE opens the TV Guide On Screen® system (Chapter 7). INFO provides detailed information on highlighted items in the TV Guide On Screen® system (Chapter 7). ENTER activates highlighted items in the main menu system and the TV Guide On Screen® system. When a menu is on-screen, these buttons select or Arrow buttons (yz x •) adjust programming menus. (Also see x / • on the next page.) CH yz cycles through programmed channels when no menu is on-screen (42) and functions as page up/down when a menu is on-screen or when the TV Guide On Screen® system is open (Chapter 7). Note: The error message “Not VOL yz adjusts the volume level. Available” will appear if you press a key for a function that is not available Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 26 HM95_R1_026-34_061505 26 6/24/05, 9:26 PM

Chapter 3: Using the remote control Learning about the remote control (continued) EXIT closes on-screen menus and the TV Guide On Screen® system. CH RTN returns to the last viewed channel (page 71), or stops the picture viewer slide show (page 88). Live returns viewing of the TV back to the live program, while continuing to record to the Toshiba Symbio™ AVHD recorder (pages 23 and 50). RECALL displays TV setting information on-screen (page 92). MUTE reduces or turns off the sound (page 84). TV/VCR selects TV mode to view one program while recording another. SKIP/SEARCH SS| and |TT jump forward and backward one day in the TV Guide On Screen® listings (Chapter 7). LIST displays the Toshiba Symbio™ AVHD recorder play list (if available) (page 23). FAV CH yz tunes to the next higher/lower favorite channel (page 44). HOME ( ) accesses the home function of the channel browser feature (page 69) x/ • While watching TV, these buttons open the channel browser banner and tune to the previous/next channel in the channel history (page 69). (Also see “Arrow buttons” on previous page.) SPLIT turnsthe POP feature on and off (page 76) or locks/unlocks the TV Guide On Screen® video window. PIC MODE selects the picture mode (page 79). FAV SCAN accesses the favorite channel search function (page 78). FREEZE accesses the freeze feature (page 78). Remote control effective range For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV. Point remote control toward remote sensor on front of TV. 16.4 ft (5m) Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 27 HM95_R1_026-34_061505 27 6/24/05, 9:26 PM

Chapter 3: Using the remote control Installing the remote control batteries To install the remote control batteries: Caution: CAUTION: Always dispose of batteries in a designated disposal location. Never Never throw batteries into a fire. throw batteries into a fire. Note: 1. Slide the battery cover off the back of the remote control. • Be sure to use AA size batteries. • Dispose of batteries in a designated disposal area. • Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations. • If the remote control does not operate correctly, or if the 2. Install two “AA” size alkaline batteries. Match the + and – symbols on operating range becomes reduced, replace batteries the batteries to the symbols on the battery compartment. with new ones. • When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination. • Always remove batteries from remote control if they are dead or if the remote control is not to be used for an 3. Slide the battery cover on to the remote control until the lock snaps. extended period of time. This will prevent battery acid from leaking into the battery compartment. Using the remote control MODE button to control your other devices Your TV remote control has one dedicated TV mode and five programmable multi-brand modes: CBL/SAT, VCR/PVR, DVD, AUDIO 1, and AUDIO 2. The default device modes and programmable device modes are listed below. Note: The TV remote control is preprogrammed to operate most Toshiba devices. If you own a non-Toshiba device or a Toshiba device that the remote control is not Number (1-6) preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” on page 31. MODE MODE Default device mode control (before programming) 1) TV Toshiba TV 2) CBL/SAT Toshiba Satellite receiver 3) VCR/PVR Toshiba VCR 4) DVD Toshiba DVD 5) AUDIO 1 Pioneer Audio receiver 6) AUDIO 2 Pioneer LD MODE Device mode control after programming Note: 1) TV Toshiba TV Although your new TV’s remote control includes 2) CBL/SAT codes for many devices, it may not include codes for some or all of the features on certain 3) VCR/PVR devices you wish to control. If you are unable to 4) DVD Multi-brand video/audio devices program the TV’s remote control to operate 5) AUDIO 1 your device or some of the features on that device, use the device’s remote control or the 6) AUDIO 2 controls on the device. You can directly select the device mode by pressing the corresponding number button (1-6) while pressing the MODE button. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 28 HM95_R1_026-34_061505 28 6/24/05, 9:27 PM

Chapter 3: Using the remote control Remote Control functional key chart Toshiba TV Cable Satellite VCR DVD/LD Receiver CD PVR Key Label (TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR) MODE Remote control device mode selection LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode.*1 SLEEP Sleep timer --- --- --- --- --- --- --- POWER Power Power Power Power Power Power Power Power 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 --- Digit 0, 10 Digit 0 100/– – (digital --- – (sub 100 +10 --- --- --- - separator) channel) INPUT TV/Video TV TV TV TV TV TV TV select PIC SIZE Selects the TV TV TV TV TV TV TV image shape. MENU/ Menu/ --- Action, --- Menu --- --- Menu ACTION Guide Menu Menu TV GUIDE/SETUP TV Guide --- Guide --- DVD setup --- --- Guide INFO/TITLE Guide Info --- INFO --- TITLE= --- --- INFO Top menu TheaterNet TheaterNet --- --- --- Subtitle --- --- ADVANCE DEVICE/SUBTITLE Device TheaterNet TheaterNet --- --- --- Audio --- --- --- CTRL/AUDIO Control ENTER Enter --- Enter, Select --- Enter --- --- Enter y Menu select --- Menu select --- Menu select --- --- Menu select up up up up z Menu select --- Menu select --- Menu select --- --- Menu select down down down down x• Menu select --- Menu select --- Menu select --- --- Menu select left/right left/right left/right left/right EXIT/ Exit --- Exit --- DVD clear --- --- EXIT DVD CLEAR CH yz Channel Channel Channel Channel --- Channel --- Channel PAGE +/– up/down, up/down up/down up/down up/down up/down Page up/down VOL yz Volume Volume Volume Volume Volume Volume Volume Volume up/down*2 up/down*2 up/down*2 up/down*2 up/down*2 up/down*2 up/down*2 up/down*2 CH RTN/ Previous Previous Previous --- DVD --- --- --- DVD RTN channel channel channel return Live Live --- --- --- --- --- --- Live TV RECALL On-screen --- --- --- On-screen --- --- --- display display Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 29 HM95_R1_026-34_061505 29 6/24/05, 9:27 PM

Chapter 3: Using the remote control Remote Control functional key chart (continued) Toshiba TV Cable Satellite VCR DVD/LD Receiver CD PVR Key Label (TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR) MUTE Sound mute*2 Sound mute*2 Sound mute*2 Sound mute*2 Sound mute*2 Sound mute*2 Sound mute*2 Sound mute*2 SLOW/ x Slow FWD Slow FWD Slow FWD ------ ------ ------ ------ ------ DIR • --- Slow REW --- SKIP/ x Skip FWD Skip FWD Skip FWD ------ ------ ------ ------ ------ SEARCH • Skip REW Skip REW Skip REW REW Rewind --- --- Rewind Rewind --- Rewind Rewind PAUSE/STEP Pause --- --- Pause Pause --- Pause Pause PLAY Play --- --- Play Play --- Play Play FF Fast FWD --- --- Fast FWD Fast FWD --- Fast FWD Fast FWD TV/VCR --- --- TV/SAT TV/VCR --- --- --- Reverse DISC/AM/FM --- --- --- --- Disc shift AM/FM Disc shift Replay STOP Stop --- --- Stop Stop --- Stop Stop REC REC Menu --- --- Record --- --- --- Record (Single Click) (Double Click) (Double Click) LIST LIST --- --- --- --- --- --- --- FAV CH yz FAV channel --- --- --- --- --- --- --- up/down HOME HOME --- --- --- --- --- --- --- SPLIT Split TV TV TV TV TV TV TV PIC MODE PIC MODE TV TV TV TV TV TV TV FAV SCAN FAV SCAN --- --- --- --- --- --- --- FREEZE Freeze TV TV TV TV TV TV TV Notes: • “---” = key does not send a signal. • “ TV” = key will operate the TV. • “ VCR” = key will operate the last active VCR or DVD. (“Last active VCR/DVD” is the mode that remains for a minimum of 5 seconds or if a key is pressed in that mode.) * 1 Backlight key is a toggle key and does not send an IR signal. * 2 Volume will punch through to TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has volume data. The AUD modes (receiver, CD) will have their own volume if volume lock is set on TV, CBL/SAT, VCR/PVR, or DVD mode. See “Using the volume lock feature” on page 32. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 30 HM95_R1_026-34_061505 30 6/24/05, 9:27 PM

Chapter 3: Using the remote control Programming the remote control to operate your other devices Device code setup Searching and sampling the code of 1. Refer to the multi-brand remote control device code table a device (8500) on pages 33–34 to find the code for the brand of your device. If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that If more than one code is listed, try each one separately until device mode and sample the functions to find the code that you find one that works. operates the target device. The keys available to be sampled, 2. Press MODE until the Mode indicator for the device provided they are applicable to that mode, are POWER, 1, (CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2) lights VOL y, CH y, and PLAY. Invalid keys will be ignored while up. in program mode. 3. While holding down the RECALL button, press the To cycle through each available device code and sample its Channel Number buttons to enter the four-digit code for functions: your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the 1. Press MODE to select the mode you want to set up. mode indicator will blink one long blink. 2. While holding down RECALL, press 8 – 5 – 0 – 0. The 4. Point the remote control at the device and press POWER to remote control will enter program mode. test the code. 3. Point the remote control at the target device and press If the device responds to the remote control: POWER (or other function buttons that are available to be sampled). You have entered the correct code. If the device does not respond to the remote control: 4. If the device responds to the remote control: You may have entered the wrong code. Repeat steps 3 Press RECALL to store the device code. The mode and 4 using another code. indicator will blink twice and the remote control will exit Note: In addition to POWER, confirm that all necessary keys the program mode. on the TV remote control operate your device. If some keys If the device does not respond to the remote control: are not operational, repeat the device code setup using Press y, and then press POWER. Repeat this step until another code (if other codes are listed for your device). If, the device responds to the remote control, and then press after trying all listed codes, the necessary keys do not operate RECALL. your device, use the device’s original remote control. Note: When a search cycle is completed, the mode 5. To control the TV, repeatedly press MODE to select “TV.” indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key Note: is pressed within 10 seconds while programming, the • Although the TV remote control includes codes for many devices, it may remote control will exit the program mode and return to the not include codes for some or all of the features on certain devices you previous code. want to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device. POWER • Each time you change the batteries you will need to reprogram the remote control. Numbers • Some newer VCRs respond to either of two codes. These VCRs have a MODE switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control. y CH y VOL y RECALL Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 31 HM95_R1_026-34_061505 31 6/24/05, 9:27 PM

Chapter 3: Using the remote control Programming the remote control to operate your other devices (continued) Using the volume lock feature (8000) Operational feature reset (8900) For the TV, CABLE/SAT, VCR, and DVD modes, the volume This feature clears all programmed features not related to “Device controls (VOL yz and MUTE) can be locked to the selected code set up” and resets the Volume Lock to “TV.” device mode. This feature does not apply to the AUDIO 1 and To reset the features: AUDIO 2 modes. While holding down the RECALL button, press 8 –9 –0 – 0. To lock the volume controls to always control the The Mode indicator will blink two times, and then pause CABLE/SAT device volume (for example): and blink two more times. 1. Repeatedly press MODE to select CABLE/SAT mode. 2. While holding down the RECALL button, press 8 – 0 – 0 – 0. 3. Press VOL y. The CABLE/SAT mode light will blink two times (locked). To reset the volume controls to the original device mode: 1. While holding down RECALL, press 8 – 0 – 0 – 0. Numbers 2. Press VOL z. MODE The mode light will blink four times (unlocked). VOL yz RECALL Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 32 HM95_R1_026-34_061505 32 6/24/05, 9:27 PM

Chapter 3: Using the remote control Multi-brand remote control device codes VCRs/PVRs VCRs/PVRs (cont.) Cable boxes Brand Code Brand Code Brand Code ADMIRAL 0135 PHILCO 0131, 0124, 0127, ABC 1124 AIWA 0127, 0132, 0181 0123, 0126, 0120, ARCHER 1132, 1125 AKAI 0129, 0114, 0115, 0143 CABLEVIEW 1105, 1132 0116 PHILIPS 0131, 0123, 0124, CITIZEN 1122, 1105 AUDIO DYNAMIC 0139, 0111 0173 CURTIS 1112, 1113 BELL&HOWELL 0105, 0113 PIONEER 0123 DIAMOND 1124, 1132, 1125 BROKSONIC 0120, 0126, 0180 PROSCAN 0145, 0100, 0123, EAGLE 1129 CANON 0123, 0125 0124, 0131, 0146, EASTERN 1134 CCE 0143 0101, 0102, 0133 GCBRAND 1132, 1105 CITIZEN 0106 QUASAR 0121, 0122, 0123, GEMINI 1122, 1143 CRAIG 0105, 0129, 0106 0124 G.I./JERROLD 1119, 1124, 1125, CURTIS MATHES 0145, 0124, 0127 RADIO SHACK 0133, 0124, 0105, 1126, 1127, 1120, DAEWOO 0143, 0101, 0124, 0136, 0109, 0140, 1121, 1122, 1111, 0175 0127 1123, 1152 DBX 0139, 0110, 0111 RCA 0133, 0145, 0100, HAMLIN 1140, 1141, 1142, DIMENSIA 0145 0123, 0124, 0131, 1145, 1118, 1112 EMERSON 0143, 0126, 0119, 0146, 0101, 0102, HITACHI 1103, 1124 0103, 0125, 0142, 0170, 0172, 0174, MACOM 1103, 1104, 1105, 0120, 0118 0176, 0183 1108 FISHER 0105, 0108, 0109, REALISTIC 0124, 0105, 0136, MAGNAVOX 1133 0107, 0113, 0165 0109, 0140, 0127 MEMOREX 1130 FUNAI 0127, 0126, 0120, Replay TV 7102 MOVIETIME 1132, 1105 0134 SAMSUNG 0137, 0102, 0104, OAK 1139, 1137, 1102 GE 0133, 0145, 0124 0133 PANASONIC 1109, 1110, 1114, GO VIDEO 0137, 0151, 0163, SAMTRON 0163 1151, 1153 0149, 0150, 0182 SANSUI 0139, 0126, 0120, PHILIPS 1128, 1129, 1130, GOLDSTAR 0106 0152 1106, 1107, 1150, GRADIENTE 0170, 0171, 0168, SANYO 0105, 0109, 0113 1131 0134, 0156 SCOTT 0101, 0102, 0104, PIONEER 1101, 1116 HITACHI 0123, 0145, 0100, 0109, 0138, 0140, PULSAR 1105, 1132 0127, 0168 0147, 0148, 0126 PUSER 1132 INSTANT REPLAY 0124, 0123 SEARS 0105, 0106, 0107, RCA 1115 JENSEN 0139 0108, 0100 REALISTIC 1132 JVC 0139, 0110, 0111, SHARP 0135, 0136, 0167, REGAL 1112, 1118, 1140, 0134, 0157, 0158, 0162 1141, 1142, 1145, 0184, 0185, 7104 SHINTOM 0117 1149 KENWOOD 0139, 0110, 0106, SIGNATURE 2000 0127, 0135 REGENCY 1134 0111 SINGER 0117 REMBRANT 1137, 1132, 1105, LG 0159 SONY 0128, 0129, 0130, 1138 LXI 0127, 0106, 0100, 0153, 0154, 0155, SAMSUNG 1105 0107, 0108, 0105, 7101 S.A. 1111, 1112, 1113 0109 SV2000 0127 SLMARK 1105, 1101 MAGNAVOX 0131, 0123, 0124, SYLVANIA 0131, 0123, 0124, SPRUCER 1105, 1110 0173 0127, 0178 STARGATE 1132, 1105 MARANTZ 0139, 0110, 0111 SYMPHONIC 0127, 0168, 0177 TELECAPTION 1148 MARTA 0106 TASHIRO 0106 TELEVIEW 1101, 1105 MEMOREX 0124, 0109 TATUNG 0139, 0110, 0111 TEXSCAN 1144 MGA 0138, 0140, 0147, TEAC 0139, 0110, 0127, TOCOM 1135, 1136, 1147 0148, 0141, 0142 0111 TOSHIBA 1104, 1146 MINOLTA 0100, 0145 TECHNICS 0121, 0122, 0123, UNIKA 1132, 1125 MITSUBISHI 0138, 0140, 0147, 0124 UNIVERSAL 1122, 1132 0148, 0141, 0142, TEKNICA 0124, 0127, 0112 VIDEOWAY 1106 0161, 0164 THOMSON 0179, 0183 VIEWSTAR 1129, 1130 MULTITECH 0147, 0127, 0104 Tivo 7100, 7101 ZENITH 1117, 1100 NEC 0139, 0110, 0111, TOSHIBA 0101, 0146, 0166, ZENITH/DRAKE 1100 0134 0160 SATELLITE OLYMPIC 0124, 0123 VECTOR RESEARCH 0111 OPTIMUS 0128, 0121, 0135, WARDS 0135, 0136, 0109, 0106 0144, 0106 ORION 0126, 0120, 0132 YAMAHA 0105, 0139, 0110, PANASONIC 0123, 0124, 0121, 0111 0122 ZENITH 0144, 0106, 0169, PENNEY 0124, 0100, 0145, 0180 0105, 0139, 0110, 0111 PENTAX 0100, 0111, 0145 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 33 HM95_R1_026-34_061505 33 6/24/05, 9:27 PM

Chapter 3: Using the remote control Multi-brand remote control device codes (continued) CD players Receivers (cont.) DVD players Brand Code Brand Code Brand Code ADMIRAL 6126 PIONEER 4105, 4107, 4150 AIWA 3123 AIWA 6133, 6135 QUASAR 4119, 4118, 4121 APEX 3120 CARVER 6129 RCA 4103, 4105, 4127, DENON 3100, 3117 DENON 6142, 6151 4131, 4130, 4149 FERGUSON 3101 EMERSON 6139 SANSUI 4103, 4111, 4139 HITACHI 3111 FISHER 6105, 6106 SHARP 4134, 4137 JVC 3109 GARRARD 6117 SONY 4122 KENWOOD 3115, 3129 HARMAN/KARDON 6120, 6121, 6123, SOUNDE-SIGH 4138 KONKA 3119 6119 TEAC 4112, 4113, 4111, MITSUBISHI 3105 HITACHI 6107 4110 NORDMENDE 3101 JENSEN 6134 TECHNICS 4121, 4118, 4119 ONKYO 3121 JVC 6140, 6141, 6145, VICTOR 4132, 4133 ORITRON 3124 6148, 6151 YAMAHA 4101, 4102 PANASONIC 3100 KENWOOD 6100, 6101, 6111, PHILIPS 3103, 3116 6145 Laser disks PIONEER 3102 LXI 6136 Brand Code RAITE 3113 MAGNAVOX 6129, 6132 DENON 5114 RCA 3101, 3106 MARANTZ 6129 HITACHI 5100 SABA 3101 MACINTOSH 6121 KENWOOD 5102, 5103 SAMPO 3114 NAKAMICHI 6110 MAGNAVOX 5101 SAMSUNG 3110 ONKYO 6114, 6115 MARANTZ 5114 SHARP 3108 OPTIMUS 6108, 6118, 6120, MITSUBISHI 5114, 5118, 5119 SILVANIA 3132, 3118 6122 NEC 5114 SMC 3125 PANASONIC 6124, 6125, 6127, PANASONIC 5104, 5105, 5106, SONY 3104, 3126, 3127, 6150 5115 3128 PHILIPS 6129, 6130, 6149 PHILIPS 5111 TECHNICS 3100 PIONEER 6108 PIONEER 5114 THOMSON 3101 QUASAR 6125, 6127, 6124 PROSCAN 5114 TOSHIBA 3103 RCA 6147, 6137, 6138, QUASAR 5104, 5105, 5106, WAVE 3122 6131, 6152 5115 YAMAHA 3100, 3130 SANSUI 6110, 6146, 6113 RCA 5114 ZENITH 3107, 3112 SANYO 6105 SAMSUNG 5112 VIALTA 3131 SCOTT 6110, 6146 SANYO 5114, 5117 FUNAI 3132, 3118 SHARP 6142, 6143 SHARP 5113, 5116 SHERWOOD 6120 SONY 5107, 5108, 5109, Satellite receivers SONY 6128 5110 Brand Code SOUNDE-SIGH 6144 TEAC 5114 DISH NETWORK 2105, 2115, 2116, TEAC 6112, 6116, 6118 TOSHIBA 5114 (Echostar) 2117 TECHNICS 6127, 6124, 6125 YAMAHA 5101 ECHOSTAR 2105 VICTOR 6140, 6141, 6145 EXPRESS VU 2105, 2115 YAMAHA 6102, 6103, 6104 G.E. 2106 G.I.(GENERAL 2108 Receivers INSTRUMENT) Brand Code GRADIENTE 2114 ADMIRAL 4120 HITACHI 2103, 2111, 2112 AIWA 4125, 4126, 4146 HNS(Hughes) 2103 DENON 4134, 4135, 4136, MAGNAVOX 2101, 2102 4143 PANASONIC 2104 FISHER 4104 PHILIPS 2101, 2102, 2118 GARRARD 4113 PRIMESTAR 2108 HARMAN KARDON 4115, 4123, 4145 PROSCAN 2106, 2109, 2110, JENSEN 4129 2113 JVC 4132, 4133, 4140, RCA 2106, 2109, 2110, 4144 2113 KENWOOD 4100, 4108, 4141, SONY 2107 4142, 4147 STAR CHOICE 2103, 2108 MAGNAVOX 4127, 4128 TOSHIBA 2100, 2103, 2119, MARANTZ 4124 2120, 2121, 2122, MCNTOSH 4116 2123, 2124, 2125 MITSUBISHI 4148 UNIDEN 2101, 2102 NAKAMICHI 4106, 4117 ONKYO 4109, 4114 OPTIMUS 4103, 4127, 4131, 4130 PANASONIC 4119, 4118, 4121 PHILIPS 4123 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 34 HM95_R1_026-34_061505 34 6/24/05, 9:27 PM

4 Menu layout and navigation The illustrations below and on the next page provide a quick overview of your TV’s menu system. Main menu layout To open the main menus (illustrated below), press MENU on the remote control or TV front panel. ➞ TV Guide On Screen® ➞ Launch Gemstar / TV GUIDE ➞ Audio Player ➞ Launch MP3 audio player Applications ➞ Picture Viewer ➞ Launch the Picture Viewer ➞ Digital CC / Audio Selector ➞ Launch the ATSC Digital CC Selector ➞ CableCARD™ ➞ Dynamic list of items provided by inserted CableCARD™ (this option is not available if CableCARD™ is not inserted) ➞ Picture Settings ➞ [ Picture Settings Edit Window ] Video ➞ Advanced Picture Settings ➞ [ Advanced Picture Settings Edit Window ] ➞ Theater Settings ➞ [ Theater Settings Edit Window ] ➞ Audio Settings ➞ [ Audio Settings Window ] Audio ➞ Advanced Audio Settings ➞ [ Advanced Audio Settings Window ] ➞ Audio Setup ➞ [ Audio Setup Window ] ➞ Favorite Channels ➞ [ Favorite Channels Edit Window ] Preferences ➞ Closed Caption Mode ➞ Off / CC1 / CC2 / CC3 / CC4 / T1 / T2 / T3 / T4 ➞ Closed Caption Advanced ➞ [ Advanced Closed Captions Window ] ➞ Input Labeling ➞ [ Input Labeling Edit Window ] ➞ Menu Language ➞ English / Français / Español ➞ Home CH Setup ➞ [ Home channel Setup Window ] ➞ Enable Rating Blocking ➞ Off / On Locks ➞ Edit Rating Limits ➞ [ Edit Rating Limits Edit Window ] ➞ Channels Block ➞ [ Channels Block Edit Window ] ➞ Input Lock ➞ Off / Video / Video+ ➞ Front Panel Lock ➞ Off / On ➞ GameTimer™ ➞ Off / 30 Min / 60 Min / 90 Min / 120 Min ➞ New PIN Code ➞ [ New PIN Code Entry Window ] ➞ Installation ➞ [ Installation sub menu is launched (see page 36 for details) ] ➞ Sleep Timer ➞ [ Sleep Timer Edit Window ] ➞ On/Off Timer ➞ [ On/Off Timer window ] Setup ➞ HDMI 1 Audio ➞ Auto / Digital / Analog ➞ HDMI 2 Audio ➞ Auto / Digital / Analog ➞ Slide Show Interval ➞ 2 sec. / 5 sec. / 10 sec. / 15 sec. / 20 sec. ➞ AVHD Skip Time ➞ 1 min. / 3 min. / 5 min. / 15 min. ➞ Gray Level ➞ 1 / 2 / 3 ➞ Quick Restart ➞ Off / On Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 35 HM95_R1_035-36_061505 35 6/24/05, 9:34 PM

Chapter 4: Menu layout and navigation Setup / Installation menu layout (continued) To open the Installation menu (illustrated below), press MENU on the remote control or TV front panel, open the Setup menu, select Installation, and press ENTER. From Main Menu/Setup menu, select “Installation” ➞ Input Configuration ➞ [ Input Configuration Window ] sub-menu ➔ ➞ Channel Program ➞ ANT1 Terrestrial ➞ ANT2 } ➞ [ Scan for new channels on desired Antenna ] ➞ Channel Add/Delete ➞ [ Channel Add / Delete Window ] ➞ Signal Meter ➞ [ Signal Meter Window ] ➞ IEEE1394 Devices ➞ [ IEEE1394 Device Management Window ] Devices ➞ TheaterNet Devices ➞ [ TheaterNet Setup Window ] TV Guide On Screen® Setup ➞ Start ➞ [ Launches TV Guide On Screen® system setup] Time and Date ➞ Start Setup ➞ [ Time And Date Setup Window ] System Status ➞ System Information ➞ [ System Information Window ] Navigating the menu system You can use the buttons on the remote TV front touchpad Remote control control or TV front touchpad to access and navigate your TV’s on-screen menu system. • Press MENU to open the menu system. • Use the up/down/left/right arrow buttons (yzx •) on the remote EXIT x • z y MENU (ENTER*) control or TV front panel to move in the corresponding direction in a menu. *The MENU button on the TV front touchpad functions MENU • Press ENTER to save your menu as the ENTER button when a menu is on-screen. settings or select a highlighted item. (A highlighted menu item appears in a ENTER different color in the menu.) y x • • All menus close automatically if you do not make a selection within 60 seconds, except the z signal meter menu which closes automatically after 5 minutes. • To close a menu instantly, press EXIT. EXIT Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 36 HM95_R1_035-36_061505 36 6/24/05, 9:35 PM

5 TV Guide On Screen® setup Setting up the TV Guide On Screen® system The TV Guide On Screen® system in your TV is a no-fee Configuring the location of your TV interactive program guide that uses the information you enter Screen 1: Select the TV location (USA), and then press during the following setup process to provide you with a ENTER. channel lineup and program listings for your area. The listings are automatically updated several times a day. Note: • You must first set up your TV according to the applicable connection instructions in Chapter 2. • If you connected a Toshiba AVHD Recorder, you TM must perform the following TV Guide On Screen® system setup in order to use the Symbio’s full functionality. See pages 23 and 50 for further details about AVHD digital recorders. To set up the TV Guide On Screen® system: Screen 2: Enter the ZIP code (U.S.A.) for your location (use the 1. Press MENU and open the Setup menu. Number buttons on the remote control for numbers and 2. Highlight Installation and press ENTER. the yz buttons for letters), and then press ENTER. Screen 3 appears. Setup Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto HDMI 2 Audio Auto Slide Show Interval 2 Sec AVHD Skip Time 15 min Navigate Select CH RTN Back EXIT Exit 3. A new set of Installation menu icons appears TV Guide On Screen Setup Screen 3: Do you have Cable service connected? on-screen (see Start If you select Yes (and press ENTER), screen 4 appears. illustration at right). If you select No (and press ENTER), screen 12 appears. Open the TV Guide On Screen® Setup menu, highlight Start, Navigate Select CH RTN Back EXIT Exit and press ENTER. 4. The following screen appears. Highlight “Set up TV Guide On Screen® now” and press ENTER to continue. Screen 4: Do you have a Cable box connected? If you select Yes (and press ENTER), screen 5 appears. If you select No (and press ENTER), screen 13 appears. 5. The following screen appears. Press ENTER to continue. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 37 HM95_R1_037-40_061505 37 6/24/05, 9:35 PM Black

Chapter 5: TV Guide On Screen® setup Setting up the TV Guide On Screen® system (continued) Screen 5: Which TV input is your cable box plugged into? Screen 9: To allow the TV Guide On Screen® system to find the If you select ANT 1, screen 6 appears. correct code for your brand of Cable box, tune your Cable If you select Video 1, screen 7 appears. box to channel 02, leave the Cable box and TV ON, and then press ENTER. Screen 10 appears. Screen 6: Select the channel your TV is tuned to when using your cable box, and then press ENTER. Screen 7 appears. Screen 10: The TV Guide On Screen® system will test the code for the brand of Cable box you selected. Do not press any keys on the TV, remote control, or Cable box until the testing process is completed. When testing is completed, screen 11 appears. Screen 7: The on-screen diagram shows the correct way to connect your Cable box to the G-LINK® terminal on the TV. Make sure the G-LINK® cable is installed properly. For additional details, see page 25. Screen 11: If your Cable box tuned itself to channel 09 after Press ENTER to display screen 8. testing, select Yes and press ENTER. If you selected ANT 1 in screen 5, screen 13 appears. If you selected Video 1 in screen 5, screen 12 appears. Screen 8: Highlight your Cable box brand, and then press ENTER to display screen 9. If your Cable box did not tune itself to channel 09 after testing and you want to test the same code again, select “Test this code again” and press ENTER. If you want to test a different code, select No and press ENTER. Screen 10 appears. Note: Many cable boxes require testing more than one code. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 38 HM95_R1_037-40_061505 38 6/24/05, 9:36 PM Black

Chapter 5: TV Guide On Screen® setup Setting up the TV Guide On Screen® system (continued) Screen 12: Do you have an antenna connected? Screen 16: The on-screen diagram shows the correct way to Select either Yes or No, and then press ENTER. Screen 13 connect your VCR to the G-LINK® terminal on the TV. appears. Make sure the G-LINK® cable is installed properly. For Note: If you selected NO in screen 3, you must select YES in additional details, see page 25. this screen to receive a channel lineup and program listings. Press ENTER to display screen 17. Screen 13: Are the settings correct? Screen 17: Select your VCR brand, and then press ENTER. If you select Yes, screen 14 appears. Screen 18 appears. If you select No, screen 1 appears. Screen 18: Turn on your VCR, insert a tape (either blank or Screen 14: Congratulations! You have completed basic previously recorded), and then press PLAY. Screen 19 TV Guide On Screen® system setup. appears. Note: Read the on-screen information regarding the amount of time it may take for listing information to download from the TV Guide On Screen® service. Press ENTER to display screen 15. Screen 19: The TV Guide On Screen® system will test the code for the brand of VCR you selected. Do not press any keys on the TV, remote control, or VCR until the testing process is completed. When testing is completed, screen 20 appears. Screen 15: Is a VCR connected? If you select Yes, screen 16 appears. If you select No, screen 21 appears. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 39 HM95_R1_037-40_061505 39 6/24/05, 9:36 PM Black

Chapter 5: TV Guide On Screen® setup Setting up the TV Guide On Screen® system (continued) Screen 20: If your VCR stopped playing the tape after testing, Screen 23: This screen provides helpful information on using select Yes and press ENTER. Screen 21 appears. your TV Guide On Screen® system. Did your VCR stop playing? Press ENTER to exit the TV Guide On Screen® setup and If your VCR did not stop playing the tape after testing and watch TV. you want to test the same code again, select “Test this code again” and press ENTER. TV Guide On Screen® Reminder If you want to test a different code, select No and press ENTER. Screen 19 appears. The TV Guide On Screen® system receives program listing data through your Cable or over-the-air video signal. In Note: Many VCRs require testing more than one code. order to receive regular program listing updates, remember to do the following: Screen 21: Review the setup information displayed on your TV 1. Leave the TV in standby mode when it is not in use by screen (an example is shown below). turning it OFF but leaving the power cord plugged in. 2. If you have a Cable box connected, leave it ON. 3. If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.) See page 13 for VCR connection instructions. 4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, follow the on-screen instructions. If the information on your TV screen is correct for your Note: If the TV power cord is unplugged for an extended period setup, select “Yes, end setup” and press ENTER. Screen 22 of time, it may take up to 24 hours with the TV in standby mode appears. (power cord plugged in and power OFF) to download the TV Guide On Screen® program schedule. It may take up to a week before an If the information is incorrect, select “No, repeat setup entire program schedule is available. process” and press ENTER. Screen 1 appears. Screen 22: Congratulations! You have successfully completed Turning off the TV Guide On Screen® TV Guide On Screen® system setup. Press ENTER to display screen 23. automatic display feature After you set up the TV Guide On Screen® system, the program guide will display automatically (default setting) when you turn on the TV. To turn off the automatic program guide: 1. Press TV GUIDE on the remote control to open the TV Guide On Screen® system (if it is not already open). 2. Use the x • buttons to select the Setup menu. 3. Use the yz buttons to select “Change Default Options,” and then press ENTER. 3. Use the yz buttons to select “General Defaults,” and then press ENTER. 5. Set the “Auto Guide” option to Off. 6. Use the yz buttons to select Done, and then press ENTER. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 40 HM95_R1_037-40_061505 40 6/24/05, 9:36 PM Black

6 Setting up your TV For menu navigation instructions, see Chapter 4. Selecting the menu language Configuring the antenna input sources You can choose from three different languages (English, French and Spanish) for the on-screen display of menus and messages. (The TV Guide On Screen® menus are in English, regardless of To configure the ANT 1 and ANT 2 input sources: the language selected in this menu.) 1. Press MENU and open the Setup menu. To select the menu language: 2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in 1. Press MENU and open the Preferences menu. step 3 below.) 2. Highlight Menu Language and press •. 3. Highlight your preferred menu language in the menu sidebar and press ENTER. Setup Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto Preferences HDMI 2 Audio Auto Favorite Channels English Slide Show Interval 2 Sec Closed Caption Mode Off Français AVHD Skip Time 15 min Closed Caption Advanced Español Input Labeling Navigate Select CH RTN Back EXIT Exit Menu Language English Home CH Setup 3. Open the Terrestrial menu, highlight Input Configuration, Navigate Select CH RTN Back EXIT Exit and press ENTER. Note: The Terrestrial menu may not be accessible (items will 4. Press EXIT to close the Preferences menu. be “grayed out”) in some instances (for example, if a cable box is connected to the ANT 1 input or if one of the VIDEO modes is the current input during TV Guide On Screen® setup). Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate Select CH RTN Back EXIT Exit 4. Press x or • to select the input source (Cable or Antenna) for the ANT 1 input on the TV. Note: If a cable box is connected to the ANT 1 input during TV Guide On Screen® setup, the entire Terrestrial menu will not be accessible, including the input source for ANT 1, which will automatically display “Cable Box.” 5. Press z and then x or • to select the input source (Cable or antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to ANT 2, skip this step. Input Configuration Antenna 1 In Cable Antenna 2 In Antenna Cancel Done 6. To save your new settings, highlight Done and press ENTER. To revert to your original settings, highlight Cancel and press ENTER. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 41 HM95_R1_041-43_061505 41 6/24/05, 9:39 PM

Chapter 6: Setting up your TV Programming channels into the TV’s channel memory When you press CHANNEL y or z on the remote control or 4. Open the Terrestrial menu, highlight Channel Program, TV front panel, your TV will stop only on the channels stored and press ENTER. in the TV’s channel memory. 5. Highlight ANT 1 or Follow the steps below to program channels into the TV’s ANT 2, depending on Terrestrial channel memory. which antenna input Input Configuration you want to program Channel Program Channel Add/Delete channels for, and then Programming channels automatically press ENTER to start Signal Meter Your TV can automatically detect all active channels in your area automatic channel and store them in its memory. After the channels are programming. Navigate Select CH RTN Back EXIT Exit programmed automatically, you can manually add or erase individual channels. ANT 1 Antenna Note: Scanning channels, please wait ... 52% • You must configure the antenna input sources before Abort programming channels (see page 41). • If the input signal type is set to CABLE for an antenna input, the The TV will automatically cycle through all the channels automatic channel programming process erases channels that were previously programmed into the TV’s memory. for the antenna input you selected, and store all active channels in the channel memory. While the TV is cycling • If the input signal type is set to ANTENNA, the automatic through the channels, the message “Scanning channels, channel programming process does NOT erase channels that please wait” appears (as shown above). were previously programmed into the TV’s memory, but adds newly found channels to the existing set of programmed 6. To cancel channel programming, either press EXIT or channels. To remove a channel from the memory, you must highlight Abort in the on-screen display and press ENTER. manually delete it (see next page). When channel programming is done, press CHANNEL • To tune the TV to a channel not programmed in the channel y or z to view the programmed channels. memory, you must use the Channel Number buttons on the remote control. • Programming channels for an antenna input configured for CABLE will take substantially longer than for an antenna input configured for ANTENNA. This is normal; however, once channel programming is completed, you should not have to repeat the programming process again unless your Cable TV Channel service lineup changes significantly. Numbers • If you have a CableCARD™ inserted (page 12), channel programming for ANT 1 is disabled because the CableCARD™ automatically loads the Cable channel list into the TV’s channel memory. To program channels automatically: 1. Make sure you have configured the antenna input sources. See page 41 for details. 2. Press MENU and open the Setup menu. 3. Highlight Installation and press ENTER. (A new set of CHANNEL yz Installation menu icons will appear on-screen). TV front touchpad Setup Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto HDMI 2 Audio Auto Slide Show Interval 2 Sec AVHD Skip Time 15 min CHANNEL z / y MENU Navigate Select CH RTN Back EXIT Exit (ENTER) Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 42 HM95_R1_041-43_061505 42 6/24/05, 9:40 PM

Chapter 6: Setting up your TV Programming channels into the TV’s channel memory (continued) Manually adding and deleting channels in To add a channel to the channel memory: the channel memory Highlight the unchecked box next to the channel number you want to add, and then press ENTER to check the box. After automatically programming channels into the channel memory, you can manually add or delete individual channels. To manually add digital subchannels on a physical channel: Use the Channel Numbers and the Dash (–/100) on the To add or delete channels in the channel memory: remote control to enter the channel number (for example, 1. Press MENU and open the Setup menu. 56–1). 2. Highlight Installation and press ENTER. (A new set of If the channel is found, the number will be added to the list Installation menu icons will appear on-screen, as shown in and the box will be checked. step 3). If the channel is not found, a message will appear. To remove a channel from the channel memory: Setup Highlight the checked box next to the channel number you Installation Sleep Timer want to remove, and then press ENTER to uncheck the On/Off Timer HDMI 1 Audio Auto box. HDMI 2 Audio Auto Slide Show Interval 2 Sec To save your new settings: AVHD Skip Time 15 min Highlight Done and press ENTER. Navigate Select CH RTN Back EXIT Exit To revert to your original settings: 3. Open the Terrestrial menu, highlight Channel Add/Delete, Highlight Cancel and press ENTER before saving. and then press ENTER. To remove all channels from the channel memory: Highlight Reset and press ENTER, and then highlight Terrestrial Done and press ENTER. Input Configuration Channel Program Note: Channel Add/Delete Signal Meter • This action applies to the current antenna input only. To delete/add channels on the other input, highlight the input you want (ANT1 or ANT 2) and press ENTER. Navigate Select CH RTN Back EXIT Exit • This action cannot be cancelled unless you highlight Cancel and press ENTER before saving your changes. 4. The illustration below left shows channels programmed for Channel Add/Delete ANT 1 the ANT 1 antenna input. To view the list of channels 2 Analog ANT 1 programmed for the Cable box or ANT 2 antenna input, 2-1 Digital ANT 2 press the y z buttons to highlight either “ANT 2” or 2-2 3 Digital Analog Cable Box “Cable Box” and press ENTER. 4 Analog 5 Digital Note: “Cable Box” will appear only if you connected a cable 6 Analog box to your TV. 7 Analog Reset 7-1 Digital Cancel Channel Add/Delete ANT 1 Channel Add/Delete ANT 2 8 Analog Done 2 Analog ANT 1 1 Analog ANT 1 2-1 Digital ANT 2 2 Analog ANT 2 2-2 Digital Cable Box 3 Analog Cable Box 3 Analog 4 Analog 4 Analog 5 Analog 5 Analog 6 Analog 6 Analog 7 Analog 7 Analog Reset 8 Analog Reset 7-1 Digital Cancel 9 Analog Cancel 8 Analog Done 10 Analog Done Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 43 HM95_R1_041-43_061505 43 6/24/05, 9:40 PM

Chapter 6: Setting up your TV Programming your favorite channels You can program up to 27 channels as favorite channels into To clear your favorite channel Edit Favorite Channels ANT 2 three Favorite Channel sets (nine channels from the ANT 1 lists: 2 2-1 input, nine from the ANT 2 input, and nine from the Cable 1. Press MENU and open the 2-2 4-1 box input). You can then scan through your favorite channels Preferences menu. 5 only, skipping other channels you do not normally watch. 2. Highlight Favorite Channels 17 - 1 17 - 2 To add and delete channels in the Favorite Channels sets: and press ENTER. 28 - 1 28 - 2 Reset Cancel 28 - 3 Done 1. Press MENU and open the Preferences menu. 3. Highlight Edit and press 2. Highlight Favorite Channels and press ENTER. ENTER. 3. Use the yz buttons to select either ANT 1, ANT 2, or 4. Highlight Reset and press ENTER. Cable box and press ENTER. 5. Highlight Done and press ENTER. 4. Highlight Edit and press ENTER. To tune your favorite channels for the current ANT input: Favorite Channels ANT 1 Press FAV CH yz. Preferences Favorite Channels Closed Caption Mode Off Empty Empty Empty ANT 1 ANT 2 To tune your favorite channels using the Closed Caption Advanced Input Labeling Empty Empty Empty Cable Box favorite channel list: Menu Language English 1 CH 4-1 Home CH Setup Empty Empty Empty Edit 1. Press 100 to display the favorite channel list. 2 CH 4-2 Done 3 CH 9 Navigate Select CH RTN Back EXIT Exit 2. Press the corresponding number button (1-9) 4 CH 10 to select your desired channel. 5 CH 12 To add a channel to the selected Favorite Channel set: Use the Note: To tune your favorite channels for another 6 CH 17 7 CH 19 yzx • buttons to highlight an unchecked box next to a channel input, you will need to change the Input Selection 8 --- you want to set as a favorite, and then press ENTER to check the first. 9 --- box. To quickly scan through your favorite channels in a nine To delete the channel from the selected Favorite Channels set: picture multi-window (for the current ANT input): Highlight a checked box and press Edit Favorite Channels ANT 1 ENTER to uncheck it. 2 Press FAV SCAN. See page 78 for details. 3 Note: If you try to add more than 4 Note: 5 Only 9 favorite channels are allowed, nine favorite channels per input, an please 6 deselect other channels first. • To tune to a channel from the FAV SCAN mode, highlight a error message will appear. You will 7 OK 8 window and press ENTER. need to delete (uncheck) a channel 9 Reset before you can add another. 10 Cancel • To scan your favorite channels for another input, you will need to 11 Done change the Input Selection first. When done, highlight Done and press ENTER. To program favorite channels for another input: Either... Highlight ANT 1, ANT 2, or Cable Box, which will change the favorite channel settings in the selected input. (This will not change the TV’s current input.) Channel Numbers Or... Press INPUT to select ANT 1, ANT 2, or Cable Box 100 and then repeat steps 1–4. “Cable Box” will appear only if you connected a cable box to your TV. y x • Favorite Channels ANT 2 z ANT 1 CH 6 Empty Empty ANT 2 Cable Box Empty Empty Empty Edit Empty Empty Empty Done FAV CH yz FAV SCAN Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 44 HM95_R1_044-52_061505 44 6/24/05, 9:47 PM Black

Chapter 6: Setting up your TV Setting up and using TheaterNet™ on-screen device control The TheaterNet feature allows you to control many brands of 5. The TheaterNet Setup menu opens. IEEE1394 and/or infrared remote-controlled A/V devices TheaterNet Setup through your TV using on-screen control icons and the TV’s Input Video 1 Select device remote control. Type Cable type, brand, and IR code Brand General Instrum... from owners Note: IR List 0000 manual. IR Code 0 0 0 0 Test • Although the TheaterNet on-screen device control feature includes Reset Done codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TheaterNet feature to operate your device Using the x • buttons, select the Input the device is or some of the features on that device, use the device’s remote connected to. control or the controls on the device. Note: When the input is changed, all unsaved settings will be • For IR pass-through device control information, see “Controlling lost. infrared remote-controlled devices through the TV (IR pass- 6. Press z and then x • to select the device Type. through)” on page 21. 7. Press z and then x • to select the device Brand. Note: When selecting a new brand, the IR code will be set to 0. Setting up TheaterNet 8. Press z and then x • to select the device’s IR code. All device types except IEEE1394 require the following setup 9. If the desired IR code is found, skip to step 10. process before you can control them using the TheaterNet on- If the desired IR code is not in the list, press z and use the screen icons. Channel Number buttons to enter the device IR code. All compatible IEEE1394 devices are automatically recognized Note: You can find the IR code for your device in the on- by the TheaterNet feature and do not require setup. screen list or in the TheaterNet device code table on pages Note: See page 22 for details about the IEEE1394 ports. If your 47–49. IEEE1394 device is not recognized through the IEEE1394 port or through the TheaterNet feature, it may be possible to set it up for IR 10. Highlight Test and press ENTER to test whether the device pass-through control as an infrared device (see page 21). responds to the code. If the device does not respond to the code, repeat steps 8 and 9 using another code for the same To set up TheaterNet device control: device. 1. Make sure you have properly connected your infrared When done, highlight Done and press ENTER or choose a remote-controlled device(s). See page 21 for details. different Input for which to set up TheaterNet device 2. Press MENU and open the Setup menu. control. 3. Highlight Installation and press ENTER. (A new set of To remove a device from TheaterNet: Installation menu icons will appear on-screen, as shown in step 4). 1. Follow steps 1–5 above. 2. Highlight Reset and press ENTER. 3. Highlight Done and press ENTER. Setup Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto HDMI 2 Audio Auto Slide Show Interval 2 Sec AVHD Skip Time 15 min Navigate Select CH RTN Back EXIT Exit 4. Open the Devices menu, highlight TheaterNet Devices, and then press ENTER. Devices IEEE1394 Devices TheaterNet Devices Navigate Select CH RTN Back EXIT Exit Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 45 HM95_R1_044-52_061505 45 6/24/05, 9:47 PM Black

Chapter 6: Setting up your TV Setting up and using TheaterNet™ on-screen device control (continued) Using the TheaterNet control icons The following are examples of the TheaterNet on-screen control icons for various devices. 1. Set up your infrared devices in TheaterNet, if you have not already done so (see page 45). Toshiba Symbio™ AVHD Recorder control* Note: IEEE1394 devices do not need to be set up in TheaterNet because they appear automatically in the TheaterNet menu. 2. Press DEVICE on the remote control to display the device TM control selection screen. *If you connected a Toshiba AVHD Recorder, you must set up the TV Guide On Screen® system in order to use the Symbio’s full functionality. See Chapter 5 for details on setting up the TV Guide On Screen® system. See pages 23 and 50 for further details about AVHD digital recorders. TheaterNet 0 Video 2 1 Video 3 Toshiba Toshiba DEVICE 2 ColorStream HD1 3 ColorStream HD2 Toshiba Toshiba CTRL y x • z ENTER Toshiba EXIT 3. Using the yzx • buttons, highlight the device you want to control and press ENTER. Toshiba TheaterNet 0 Video 2 1 Video 3 CH Toshiba Toshiba 2 ColorStream HD1 3 ColorStream HD2 Toshiba Toshiba 4. The input automatically changes to the input for the selected device, and the device’s control icons display on- screen. Toshiba ColorStream HD1 ENTER TOP MENU SELECT EXIT Highlight the icon for the function you want to control and press ENTER. To select the device’s control icons directly: Press CTRL. To close the on-screen control icons: Press EXIT. To view another source: Press DEVICE and select the input source you want to view. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 46 HM95_R1_044-52_061505 46 6/24/05, 9:47 PM Black

Chapter 6: Setting up your TV TheaterNet™ IR device codes Amplifiers Cable boxes (cont.) CD players (cont.) Brand Code Brand Code Brand Code Aiwa 0406 RadioShack 0015 Proton 0157 Bose 0674 Regal 0020, 0273, 0279 QED 0157 Carver 0269 Rembrandt 0011 Quasar 0029 Curtis Mathes 0300 Runco 0000 RCA 1062, 0032, 0053, Denon 0160 Samsung 0144 0179, 0305, 0468, GE 0078 Scientific Atlanta 0877, 0008, 0017, 0764 Harman/Kardon 0892 0477, 1877 Realistic 0179, 0180, 0420 JVC 0331 Signal 0015 Rotel 0157, 0420 Left Coast 0892 Signature 0011 SAE 0157 Linn 0269 sony 1006 Sansui 0157, 0305 Luxman 0165 Starcom 0003, 0015 Sanyo 0179 Magnavox 0269 Stargate 0015 Scott 0305 Marantz 0892, 0321, 0269 Starquest 0015 Sears 0305 NEC 0264 Supercable 0276 Sharp 0861, 0037, 0180 Nakamichi 0321 Tocom 0012 Sherwood 1067, 0180 Optimus 0395, 0300 Torx 0003 Sonic Frontiers 0157 Panasonic 0308, 0521 Toshiba 0000 Sony 0490, 0000, 0100, Parasound 0246 Tusa 0015 0185, 0604, 1364 Philips 0892, 0269 United Artists 0007 Soundesign 0145 Pioneer 0013, 0300 Zenith 0000, 0525, 0899 TDK 1208 Polk Audio 0892, 0269 Tascam 0420 RCA 0300 CD players Teac 0174, 0180, 0393, Realistic 0395 Brand Code 0420 Sansui 0321 Aiwa 0157, 0124 Technics 0029, 0303 Shure 0264 Burmester 0420 Victor 0072 Sony 0689, 0220 California Audio Labs 0029, 0303 Wards 0157, 0053 Soundesign 0078, 0211 Carver 0157, 0179, 0437 Yamaha 0888, 0036, 0187, Technics 0308, 0521 Classic 1297 1292 Victor 0331 DKK 0000 Yorx 0461 Wards 0078, 0013, 0211 DMX Electronics 0157 Yamaha 0354, 0133 Denon 0873, 0003 Laser disk players Emerson 0305 Brand Code Fisher 0174, 0179, 1325 Aiwa 0203 Cable boxes GPX 1296 Carver 0064, 0194, 0323 Brand Code Garrard 0393, 0420 Denon 0059, 0172 ABC 0003, 0008, 0014, Genexxa 0032, 0305 Disco Vision 0023 0007, 0011, 0017 Harman/Kardon 0157, 0173 Funai 0203 Americast 0899 Hitachi 0032 Harman/Kardon 0194 Bell & Howell 0014 JVC 0072, 1294 Hitachi 0023 Bell South 0899 KLH 1318, 1372, 1373 Magnavox 0194, 0217 Contec 0019 Kenwood 0681, 0826, 0626, Marantz 0064, 0194 Director 0476 0028, 0037, 0190 Mitsubishi 0059 Everquest 0015 Koss 1317 NAD 0059 Gemini 0015 Krell 0157 Optimus 0059 General Instrument 0476, 0003, 0276, LXI 0305 Panasonic 0204 0011, 0810 Linn 0157 Philips 0064, 0194 GoldStar 0144 MCS 0029 Pioneer 0059, 0023 Hamlin 0009, 0020, 0273 MTC 0420 Polk Audio 0194 Hitachi 0011 Magnavox 0157, 0305 Quasar 0204 Hytex 0007 Marantz 0626, 0029, 0157, Realistic 0203 Jasco 0015 0180 Samsung 0323 Jerrold 0476, 0003, 0276, Miro 0000 Sega 0023 0012, 0014, 0015, Mission 0157 Sony 0193, 0201 0011, 0810 NSM 0157 Technics 0204 Memorex 0000 Nikko 0174 Theta Digital 0194 Motorola 0476, 1106, 0276, Onkyo 0868, 0101 Yamaha 0217 0810 Optimus 1063, 0000, 0032, Oak 0019, 0007 0037, 0145, 0179, Miscellaneous audio devices Pace 0237 0305, 0420, 0437, Brand Code Panasonic 0000, 0107 0468 Aiwa 0010, 0159, 0404 Paragon 0000 Panasonic 0029, 0303 Fisher 0052 Philips 0305, 0317 Parasound 0420 JVC 0073 Pioneer 0877, 0144, 0533, Philips 0626, 0157 Jerrold 0520, 0459 1877 Pioneer 1063, 1062, 0032, Scientific Atlanta 0460 Pulsar 0000 0305, 0468 Sony 0010, 0159, 0576 Quasar 0000 Polk Audio 0157 Starcom 0459 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 47 HM95_R1_044-52_061505 47 6/24/05, 9:48 PM Black

Chapter 6: Setting up your TV TheaterNet™ IR device codes (continued) Video accessory (HDTV decoder) Receivers (cont.) VCRs Brand Code Brand Code Brand Code Panasonic 1120 Proscan 1254 Admiral 0048, 0209 Pioneer 1010 Quasar 0039 Adventura 0000 Princeton 0113, 0295 RCA 1023, 1254, 0080, Aiko 0278 Samsung 1190 0531, 1390, 1609 Aiwa 0037, 0000 Sensory Science 1126 Realistic 0181, 0195 Akai 0041 Sharp 1010 Samsung 1295 America Action 0278 Sansui 1089, 0189 American High 0035 Sanyo 0801, 1251 Asha 0240 Receivers Sharp 0186, 1286 Audiovox 0037, 0278 Brand Code Sherwood 0491, 0502, 1653 Beaumark 0240 ADC 0531 Sony 1058, 1258, 1158, Bell & Howell 0104 Aiwa 1089, 1405, 0121, 0158, 0474, 1367, Broksonic 0184, 0121, 0209, 0158, 0189, 0405, 1558, 1658,1758 0002, 0479, 1479 1388, 1641 Soundesign 0670 CCE 0072, 0278 Alco 1390 Stereophonics 1023 Calix 0037 Anam 1609 Sunfire 1313 Canon 0035 Apex Digital 1257 Teac 0463 Carver 0081 Arcam 1120 Technics 1308, 1309, 1518, Cineral 0278 Audiotronic 1189 0039, 0309 Citizen 0037, 0278, 1278 Audiovox 1390 Thorens 1189 Colt 0072 Bose 1229 Venturer 1390 Craig 0037, 0047, 0240, Cambridge Soundworks 1370 Victor 0074 0072 Capetronic 0531 Wards 0014, 0080, 0158, Curtis Mathes 0060, 0035, 0162, Carver 1089, 1189, 0042, 0189 0041, 0760, 1035 0189 Yamaha 0176, 0186, 1176 Cybernex 0240 Casio 0195 Yorx 0195 Daewoo 0045, 0278, 1278 Clarinette 0195 Zenith 0857 Denon 0042 Compaq 1136 Dynatech 0000 Curtis Mathes 0080 Electrohome 0037 Daewoo 1250 Satellite receivers Electrophonic 0037 Denon 1104, 1160, 0004, Brand Code Emerex 0032 1360 AlphaStar 0772 Emerson 0037, 0184, 0000, Fisher 0042, 1801 Chaparral 0216 0121, 0043, 0209, Garrard 0463 Crossdigital 1109 0002, 0278, 0479, Harman/Kardon 0110, 0189, 0891 DishPro 1005, 0775 1278, 1479 Hewlett Packard 1181 Echostar 1005, 0775 Fisher 0047, 0104 JBL 0110, 1306 Expressvu 0775 Fuji 0035, 0033 JVC 0074, 1374 GE 0566 Funai 0000 KLH 1390 GOI 0775 GE 0060, 0035, 0240, Kenwood 1313, 1027, 1570, General Instrument 0869 0760, 0807, 1035, 1569, 0027, 0042, HTS 0775 1060 0186 Hitachi 0819 Garrard 0000 Koss 1366 Hughes Network Systems 1142, 0749, 1749 Go Video 0432 LXI 0181 JVC 0775 GoldStar 0037, 0038, 1237 Lasonic 1798 Magnavox 0724, 0722 Gradiente 0000 Linn 0189 Memorex 0724 HI-Q 0047 Lloyd’s 0195 Mitsubishi 0749 Harley Davidson 0000 MCS 0039 Motorola 0869 Harman/Kardon 0081, 0038 Magnavox 1089, 1189, 0189, Next Level 0869 Harwood 0072 0195, 0391, 0531 Panasonic 0247, 0701 Headquarter 0046 Marantz 1089, 1189, 0039, Paysat 0724 Hitachi 0000, 0042, 0041 0189 Philips 1142, 0749, 0724, Hughes Network Systems 0042 Modulaire 0195 1076, 0722, 1749 JVC 0067, 0041 Musicmagic 1089 Proscan 0392 Jensen 0041 Nakamichi 0097 RCA 0392, 0566, 0855, KEC 0037, 0278 Onkyo 0135, 0842, 1298 0143 KLH 0072 Optimus 1023, 0042, 0080, RadioShack 0869 Keen 0693 0181, 0186, 0531, SKY 0856 Kenwood 0067, 0041, 0038 0670, 0738, 0801 Samsung 1109 Kodak 0035, 0037 Panasonic 1518, 0039, 0309, Sony 0639 LXI 0037 0367 Star Choice 0869 Lloyd’s 0000 Penney 0195 Toshiba 0749, 0790, 1052, Logik 0072 Philips 1089, 1189, 1269, 1053, 1054, 1285, MEI 0035 0189, 0391, 1120 1286, 1287, 1289, MGA 0240, 0043 Pioneer 1023, 0014, 0080, 1749 MGN Technology 0240 0150, 0244, 0531, Uniden 0724, 0722 MTC 0240, 0000 0630, 1384 Zenith 0856, 1856 Magnasonic 1278 Polk Audio 0189 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 48 HM95_R1_044-52_061505 48 6/24/05, 9:48 PM Black

Chapter 6: Setting up your TV TheaterNet™ IR device codes (continued) VCRs (cont.) VCRs (cont.) DVD players (cont.) Brand Code Brand ` Code Brand Code Magnavox 0035, 0039, 0081, Scott 0184, 0045, 0121, Hitachi 0573, 0664 0000, 0149, 0563, 0043 Hiteker 0672 1781 Sears 0035, 0037, 0047, JBL 0702 Magnin 0240 0000, 0042, 0104, JVC 0558, 0623, 0867 Marantz 0035, 0081 0046, 1237 KLH 0717 Marta 0037 Semp 0045 Kenwood 0490, 0534, 0682, Matsushita 0035, 0162, 0454 Sharp 0048, 0807, 0848 0737 Memorex 0035, 0162, 0037, Shintom 0072 Konka 0711, 0719, 0720, 0048, 0039, 0047, Shogun 0240 0721 0240, 0000, 0104, Singer 0072 Koss 0651 0209, 0046, 0454, Sonic Blue 0614, 0616 Lasonic 0798 0479, 1037, 1162, Sony 0035, 0032, 0000, Magnavox 0503, 0675 1237, 1262 0033, 0636, 1032, Malata 0782 Minolta 0042 1232 Marantz 0539 Mitsubishi 0067, 0043, 0807 Sylvania 0035, 0081, 0000, Microsoft 0522 Motorola 0035, 0048 0043, 1781 Mintek 0717 Multitech 0000, 0072 Symphonic 0000 Mitsubishi 0521 NEC 0104, 0067, 0041, TMK 0240 Nesa 0717 0038 Tatung 0041 Next Base 0826 Nikko 0037 Teac 0000, 0041 Norcent 0872 Noblex 0240 Technics 0035, 0162 Onkyo 0503, 0627 Olympus 0035 Teknika 0035, 0037, 0000 Oritron 0651 Optimus 1062, 0162, 0037, Thomas 0000 Panasonic 0490, 0632, 1362, 0048, 0104, 0432, Tivo 0618, 0636 1462, 1490 0454, 1048, 1162, Toshiba 0045, 0043, 0845 Philips 0503, 0539, 0646, 1262 Totevision 0037, 0240 0854 Orion 0184, 0209, 0002, Unitech 0240 Pioneer 0525, 0571, 0632 0479, 1479 Vector 0045 Polk Audio 0539 Panasonic 1062, 0035, 0162, Vector Research 0038 Princeton 0674 0225, 0454, 0616, Video Concepts 0045 Proscan 0522 1035, 1162, 1262 Videomagic 0037 RCA 0522, 0571, 0717, Penney 0035, 0037, 0240, Videosonic 0240 0822 0042, 0038, 1035, Villain 0000 Rotel 0623 1237 Wards 0060, 0035, 0048, Rowa 0823 Pentax 0042 0047, 0081, 0240, Sampo 0698 Philco 0035, 0209, 0479 0000, 0042, 0072, Samsung 0573, 0820 Philips 0035, 0081, 0618, 0149, 0760 Sansui 0695 1081, 1181 White Westinghouse 0209, 0072, 1278 Sanyo 0670 Pilot 0037 XR-1000 0035, 0000, 0072 Sharp 0630 Pioneer 0067 Yamaha 0038 Sherwood 0633 Polk Audio 0081 Zenith 0039, 0000, 0209, Shinsonic 0533 Profitronic 0240 0033, 0479, 1479 Sony 0533, 0864, 1533 Proscan 0060, 0760, 1060 Sylvania 0675, 0821 Protec 0072 Technics 0490 Pulsar 0039 DVD players Techwood 0692 Quarter 0046 Brand Code Theta Digital 0571 Quartz 0046 Toshiba 0503, 0695, 1045 Aiwa 0641 Quasar 0035, 0162, 0454, Tredex 0800 Apex Digital 0672, 0717, 0755, 1035, 1162 Urban Concepts 0503 0794, 0796, 0797, RCA 0060, 0240, 0042, XBox 0522 0830, 0856, 1100 0149, 0760, 0807, Audiologic 0736 1035, 1060 B&K 0655, 0662 RadioShack 0000, 1037 Blue Parade 0571 Radix 0037 Broksonic 0695 Randex 0037 DVD2000 0521 Realistic 0035, 0037, 0048, Daewoo 0784 0047, 0000, 0104, Denon 0490, 0634 0046 Emerson 0591 ReplayTV 0614, 0616 Enterprise 0591 Runco 0039 Fisher 0670 STS 0042 GE 0522, 0717 Samsung 0240, 0045 GPX 0699, 0769 Sanky 0048, 0039 Go Video 0715 Sansui 0000, 0067, 0209, Gradiente 0651 0041, 0479, 1479 Greenhill 0717 Sanyo 0047, 0240, 0104, Harman/Kardon 0582, 0702 0046 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 49 HM95_R1_044-52_061505 49 6/24/05, 9:48 PM Black

Chapter 6: Setting up your TV Setting the AVHD device skip time Setting the time and date When you connect an external AVHD (audio/video hard drive) Note: If you already set up the TV Guide On Screen® system, the device—such as the Toshiba Symbio™ AVHD Recorder—to time and date were set automatically and you can skip this step. one of the TV’s IEEE1394 ports, you can use the AVHD device To set the time and date: skip time feature to set the number of minutes the device will skip forward or backward when you press the SKIP buttons. 1. Press MENU and open the Setup menu. Note: 2. Highlight Installation and press ENTER. (A new set of TM Installation menu icons will appear on-screen, as shown in • This TV will work best with the Toshiba AVHD Recorder for recording high definition and standard definition step 3 below.) material from either tuner and for controlling live TV (pause/rewind/ 3. Open the Time And Date menu, highlight Start Setup, and etc.). When the Symbio AVHD Recorder is connected to the TV, the press ENTER. remote control keys (LIVE, STOP, REW, PAUSE, PLAY, etc.) are automatically activated to allow pausing of live TV. Time And Date • When you connect an AVHD (or D-VHS) device, the TV Guide Start Setup On Screen® system is automatically configured to allow recording. See page 23 for device connection information. See Chapters 5 and 7 for details about setting up and using the TV Guide On screen® system. To set the AVHD device skip time: Navigate Select CH RTN Back EXIT Exit 1. Press MENU and open the Setup menu. 2. Highlight AVHD Skip Setup Installation If you have not set up the TV Guide On Screen® system, 1 min Time and press •. Sleep Timer 3 min the following screen will appear. To set the time, highlight On/Off Timer HDMI 1 Audio Auto 5 min TV Guide On Screen® and press ENTER. The TV Guide 3. Press y or z to select HDMI 2 Audio Auto 15 min On Screen® setup sequence will start, and the time and date the AVHD skip time (1, Slide Show Interval AVHD Skip Time 2 Sec 15 min will be set automatically. 3, 5, or 15 minutes) and Navigate Select CH RTN Back EXIT Exit press ENTER. Time And Date Your TV Guide On Screen system can provide accurate time and date information. It is recommended you set up TV Guide On Screen first and use it to obtain the time and date. Setting the HDMI™ audio mode Manual TV Guide On Screen Cancel To set the HDMI audio mode: If you have already set up the TV Guide On Screen® 1. Press MENU and open system, the time and date setting screen will appear and you the Setup menu. will need to manually set the time and date. Setup 2. Highlight HDMI 1 (or Installation Auto Time And Date 2) Audio and press •. Sleep Timer On/Off Timer Digital Analog Date (MM/DD/YY) 0 6/3 0/0 5 HDMI 1 Audio Auto 3. Press z or y to select HDMI 2 Audio Auto Time (HH:MM) 1 1 : 1 1 AM the HDMI audio mode Slide Show Interval AVHD Skip Time 2 Sec 15 min (Auto, Digital, or Navigate Select CH RTN Back EXIT Exit Analog) and press Cancel Done ENTER. (Auto is the recommended mode). See “Connecting an HDMI or a DVI device to the HDMI input” on page 19. Note: • If you highlight TV Guide On Screen® (above) to set the time and date through the TV Guide On Screen® system and a power outage occurs, the time and date will be updated automatically when the power is restored. • If you highlight Manual (above) to set the time and date manually and a power outage occurs, you will lose the time and date settings when the power is restored. • If you manually set the time and date and then perform TV Guide On Screen® setup, the manual time and date settings will be overridden by the TV Guide On Screen® settings. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 50 HM95_R1_044-52_061505 50 6/24/05, 9:48 PM Black

Chapter 6: Setting up your TV Viewing the CableCARD™ menu Setting the Quick Restart Feature A CableCARD™ enables you to view encrypted digital channels. With the Quick Restart feature set to ON, the TV will stay in See page 12 for connection and subscription information. Low Power Shutdown mode for several minutes after the TV is After the CableCARD™ is inserted, a CableCARD™ option turned off (see Notes below). appears in the Applications menu, with informational screens If the TV is turned on from Low Power Shutdown mode, the provided by your digital CableCARD™ service (see illustrations full picture appears immediately. below). To set the Quick Restart feature: CableCard Connected -- Acquiring channel information. 1. Press MENU, and then press x or • until the Setup menu CableCard services will only operate appears. with cable signal connected to Antenna 1. 2. Press z or y to highlight Quick Restart, and then press •. 3. Press z or y to select either “On” or “Off ” and press To view the CableCARD™ menu: ENTER to display the information. 1. Press MENU and open the Applications menu. 2. Highlight CableCARD™ and press •. Setup 3. Press z or y to select one of the side menu items and press On/Off Timer Off ENTER to display the information. HDMI 1 Audio HDMI 2 Audio Auto Auto On Slide Show Interval 2 Sec AVHD Skip Time 15 min Gray Level 2 Quick Restart On Applications TV Guide On Screen IP Service Navigate Select CH RTN Back EXIT Exit Audio Player Conditional Access Picture Viewer CableCARD(tm) Status Digital CC/Audio Selector Network Setup Note: CableCARD CableCARD(tm) Pairing If Quick Restart is set to Off and you turn off the TV, it can take several seconds for the picture to appear when you turn on the TV Navigate CH RTN Back EXIT Exit Select again. If Quick Restart is set to On and you turn off the TV, the following Note: The CableCARD™ menu is for informational purposes will occur for a few minutes: only and has no user-adjustable options. • The screen (lamp) lights dimly. • The fans continue to run. This is a function of the Quick Restart Low Power Shutdown mode and is not a TV malfunction. If you do not prefer this, set the Quick Restart feature to Off. When the Quick Restart feature is set to Off, if you repeatedly turn the TV on and off in a short period of time, the useful service life of the lamp may be shorter than the average useful service life. See page 103. IMPORTANT NOTICE ABOUT “HOT LAMP RESTART” When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen in the following situations: • When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes. • If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains power within a few minutes. This is a property of DLP TV lamp technology and is NOT a sign of malfunction. If this occurs, the green LED on the TV front panel will blink (and the red LED will be lit solid) until the TV is finished restarting the lamp and the normal picture appears. If BOTH green and red LEDs are blinking at a one-second rate, you will need to turn the TV off and then on again to restart the lamp. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 51 HM95_R1_044-52_061505 51 6/24/05, 9:48 PM Black

Chapter 6: Setting up your TV Viewing the digital signal meter Viewing the system status You can view the digital signal meter for the ANT 1 and ANT 2 To view the system status: digital TV input sources only. 1. Press MENU and open the Setup menu. To view the digital signal meter: 2. Highlight Installation and press ENTER. (A new set of 1. Press MENU and open the Setup menu. Installation menu icons will appear on-screen, as shown 2. Highlight Installation and press ENTER. (A new set of below right). Installation menu icons will appear on-screen, as shown in step 3 below.) Setup System Status Installation System Infomation Sleep Timer On/Off Timer HDMI 1 Audio Auto Setup HDMI 2 Audio Auto Installation Slide Show Interval 2 Sec Sleep Timer AVHD Skip Time 15 min On/Off Timer Navigate Select CH RTN Back EXIT Exit Navigate Select CH RTN Back EXIT Exit HDMI 1 Audio Auto HDMI 2 Audio Auto Slide Show Interval 2 Sec 3. Open the System Status menu, highlight System AVHD Skip Time 15 min Information, and then press ENTER. Navigate Select CH RTN Back EXIT Exit 4. Use the x • buttons to scroll through the menu bar to 3. Open the Terrestrial menu, highlight Signal Meter, and check the Product Information and Software Version. press ENTER. System Information System Information Product Information Software Version Brand: Toshiba 0.3.0 Model: 52HM95 Mar 9 2005 - 12:37:10 IEEE1394 GUID: 00003914-28343803 FW:0.12 Terrestrial Sub:47 Input Configuration Channel program Channel Add/Delete OK OK Signal Meter To close the screen and return to the Installation menu: Navigate Select CH RTN Back EXIT Exit Highlight OK and press ENTER. To return to normal viewing: 4. Use the yzx • buttons to select the antenna input and Press EXIT. digital channel whose signal you want to check. Note: The physical digital channel number listed in the Signal Restore Factory Defaults Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF To restore all settings and channels to their factory default channel numbers for your local digital stations. values: Signal Meter 1. Follow steps 1–3 above. Signal Locked 2. Use the x • buttons to scroll through the menu bar to 0 Peak 0 select Factory Defaults. Antenna Physical Digital Channel 1 13 3. Enter your PIN code (or 0000 if no PIN code has been set). Virtual Digital Channel N/A OK 4. Highlight Yes and press ENTER. The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to To close the screen and return to the Terrestrial menu: complete the restore process. Highlight OK and press ENTER. To cancel the reset: To return to normal viewing: Highlight No and press ENTER. Press EXIT. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 52 HM95_R1_044-52_061505 52 6/24/05, 9:48 PM Black

7 Using the TV Guide On Screen® interactive program guide The TV Guide On Screen® system is a free, interactive, • Direct tuning—Directly tune the TV to a current program on-screen program guide built in to your Toshiba TV that lists you want to watch by selecting it in the program guide. schedules and information for TV programs in your area. • Reminders—Schedule show reminders that will either display Note: Over-the-air or cable access to stations carrying TV Guide an on-screen notification banner or automatically tune the TV On Screen® data is required for the TV Guide On Screen® system to to the channel of the show for which you set the reminder. operate. The TV Guide On Screen® system does not work with satellite • Recording—Easily schedule recording of one or more programming. Toshiba does not provide the TV Guide On Screen® data; rather, such data is provided by a third party, which is responsible for its programs. accuracy and availability. Additionally, occasional compatibility issues may Note: A VCR or IEEE1394 recording device is required for recording. exist between the TV Guide On Screen® system contained in your TV and It is recommended that you connect your devices according to the the data provided by the third party. If you experience any performance instructions in Chapter 2. issues with your TV Guide On Screen® system, please contact Toshiba • Search—Search for shows by category, keyword, or Consumer Solutions by calling (800) 631-3811 or by visiting alphabetically. http://www.tacp.com/customersupport/contact.asp. • On-screen help—The TV Guide On Screen® system contains The TV Guide On Screen® system includes the following on-screen feature definitions and navigation instructions. features: • Streamlined on-screen assisted setup—Quickly and easily set To open the TV Guide On Screen® system: up your TV Guide On Screen® system using the on-screen • While watching TV, press prompts (see “Setting up the TV Guide On Screen® system” the TV GUIDE button Applications below). on the remote control; TV Guide On Screen • Program listings and INFO windows—Scroll through eight —or— Audio Player Picture Viewer days of TV listings and view program information such as • Press MENU, open the Digital CC/Audio Selector CableCARD rating, stereo, HDTV, new episode. Applications menu, • Watch TV and display TV Guide On Screen® information highlight TV Guide simultaneously. On Screen®, and press Navigate Select CH RTN Back EXIT Exit ENTER. • Channel lineup customization—Customize your channel lineup so your favorite stations are listed first. Note: After setting up the TV Guide On Screen® system, the program guide opens automatically by default when you turn on the TV. To turn off this feature, see page 40. Setting up the TV Guide On Screen® system Follow these instructions to set up the TV Guide On Screen® 1. Press MENU and open the Setup menu. system so it can receive current program data for your area. Note: If you move the TV to a different ZIP/postal code, you will 2. Highlight Installation and then press ENTER to open the need to perform the TV Guide On Screen® Setup process to Installation menus. (A new set of menu icons will appear reconfigure your TV Guide On Screen® system. on-screen, as shown in step 4 below.) If you have not already connected your antenna, cable box, 3. Open the TV Guide On Screen® Setup menu, highlight and/or recording device, see Chapter 2 for connection Start, and then press ENTER. instructions. Note: You must connect a VCR or an IEEE1394 compatible Setup TV Guide On Screen Setup recording device to use the TV Guide On Screen® system’s Installation Sleep Timer Start one-touch recording feature. It is recommended that you On/Off Timer HDMI 1 Audio Auto connect your devices according to the connection instructions HDMI 2 Audio Auto in Chapter 2. Slide Show Interval AVHD Skip Time 2 Sec 15 min Navigate Select CH RTN Back EXIT Exit Navigate Select CH RTN Back EXIT Exit The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and 4. Go to Chapter 5 for instructions on completing the setup. other countries, and may subject you to civil and criminal liability. Read this chapter for details on using the TV Guide On Screen® interactive program guide. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 53 HM95_R2_053-56_062705 53 6/27/05, 6:55 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide Navigating the TV Guide On Screen® system • While watching TV, press the TV GUIDE button to enter the TV Guide On Screen® system. The LISTINGS screen will appear with the current show highlighted. • When in the TV Guide On Screen® system, if you press the TV GUIDE button from any screen, the TV will tune to the show displayed in the Video Window. • Use the arrow keys on the remote control (yzx •) to highlight any show, and then press ENTER to tune to that show. • Scroll left or right (x •) to view eight days of listings. • Press MENU to display a panel menu with options for the currently Note: highlighted program or tile, including setting recordings and reminders. • The TV Guide On Screen® menus shown in this manual are for • To access another Service screen: illustration purposes only. The channels, programs, and TV Guide On Screen® information as illustrated may not be 1. Press y to highlight the Service Bar. available in your area. The options and features as illustrated 2. Press x or • to highlight a different Service (LISTINGS, SEARCH, are subject to change when updates are downloaded from the SETUP, SCHEDULE, or RECORDINGS). TV Guide On Screen® service to your TV. • The TV Guide On Screen® interactive program guide supports 3. Press z to use that Service. cable-ready, cable box, and digital cable services, as well as Note: Helpful information about each Service appears in the Info Box. over-the-air broadcasts. It does not provide listings for satellite services. TV Guide On Screen® remote control functions BUTTON FUNCTION Numbers } TV GUIDE • When watching TV, enters the TV Guide On Screen® system and highlights the current show listing. • When in the TV Guide On Screen® system, returns to watching TV and displays the show in the Video Window. – (digital Numbers • For direct channel tuning, priority ordering, and channel editing. separator) – (digital separator) • For entering digital channel numbers. MENU MENU • Displays the panel menu, in which you can choose options (for example, record, remind, INFO keyword). INFO • Cycles between levels of information, as available, in a Service screen or other type of screen. TV GUIDE ENTER • Makes a selection or executes an action. ENTER • With a currently airing show listing highlighted, returns to watching TV and tunes to the show y x • channel. z • With a future airing show listing highlighted, displays a panel menu with viewing options. PAGE UP/ y zx • • Provide directional control. DOWN • When watching TV, y and z provide surfing through channels turned ON in the LISTINGS screen. PAGE UP/DOWN • When in the TV Guide On Screen® system, moves from one set of screen information to the SS| and |TT next, when applicable. REC • When in the TV Guide On Screen® system or watching TV, initiates the recording process. REC SPLIT • When in the TV Guide On Screen® system, toggles between locking and unlocking the Video Window. SPLIT SS| and |TT • Jump forward and backward one day in the LISTINGS screen. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 54 HM95_R2_053-56_062705 54 6/27/05, 6:55 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide Navigating the TV Guide On Screen® system (continued) Video Window • When you open the TV Guide On Screen® system, the current program appears in the Video Window. • As you scroll through the listings, the Video Window will change to display the selected program. Info Box • The lock/unlock icon indicates the status of the Video Window. • You can set the Video Window to remain on a single channel (locked) or to change channels (unlocked) as you navigate through listings. To lock/unlock the Video Window: Press the SPLIT button on the remote control to toggle between locking and unlocking the Video Window. —or— Highlight a channel logo or the LISTINGS Service Bar Label and press MENU to display the option to lock/unlock the Video Window. Panel Menus • A panel menu appears: – when you press MENU on a highlighted tile (if additional options are available); or – when you press ENTER on a show starting in the future. • When a panel menu appears, the highlighted tile changes color to indicate that the panel menu relates to the tile. • Press INFO to display help for the current panel menu. • Press y and z to move among the options. • Press x and • to move to adjacent options or, if the highlight is on a odometer, to change the odometer choice. • To move the highlight to the default command button, press ENTER from an odometer or entry box. • To execute the action and close the panel menu, highlight the command button and press ENTER. • To cancel any changes and close the panel menu: – press MENU; or – highlight Cancel and press ENTER. • If a panel menu contains more options than can be displayed in one panel, the word “more” appears at the bottom of the menu. To access the additional options, either scroll down using the z button or the PAGE UP/DOWN (CH yz) button. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 55 HM95_R2_053-56_062705 55 6/27/05, 6:56 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide Navigating the TV Guide On Screen® system (continued) Info Box • An Info Box contains information about a show, Service, or Panel Ad, or Info Action Bar provides general help (for example, for a panel menu). • An Info Box for a program in the LISTINGS screen can have up to three sizes: Small, Large, or “No.” – Press INFO on the remote control to cycle among the sizes. – The default Info Box size is Small. To change the default size, open the SETUP Service screen (see page 66). Small Info Box • The Info Button icon ( ) appears on the Info Action Bar if the Info Box size can change and/or if there are additional Info screens. Press the INFO key on the remote control to change the size and/or to display additional Info screens. • In some instances, the INFO button on the remote control is used to page forward (for example, if there are additional pages of information in a Panel Large Info Box Ad, a Channel Ad, or help text). TV Guide On Screen® Icons ICON NAME DESCRIPTION Info Button • Additional Info Box information is available, or the Info Box has additional sizes. Progress Bar • Elapsed time in current show. • Progress bar appears in LISTINGS and SEARCH and when the Info Button is pressed while watching TV. HDTV • Show is presented in high-definition TV, if available. New • Show is new (not a repeat). Stereo • Show is available in stereo. Dolby Digital • Show is available with Dolby Digital 5.1 audio (digital channels only). CC • Closed captioning is available for the show. TV Rating • TV rating for the show. Record Once • Show is set to Record Once. • Other frequencies are Daily (manual recording only), Regularly, and Weekly. Record Off • Show is set to Record but is currently Off (show remains in Schedule). Record • Show is Suspended due to a schedule conflict (show remains in Schedule). Suspended • Recording resumes when the conflict no longer exists. Remind Once • Show is set to Remind Once. • Other frequencies are Daily (manual reminding only), Regularly, and Weekly. Remind Off • Show is set to Remind but is currently Off (show remains in Schedule). Remind • Show is Suspended due to a schedule conflict (show remains in Schedule). Suspended • Remind resumes when the conflict no longer exists. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 56 HM95_R2_053-56_062705 56 6/27/05, 6:56 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services The TV Guide On Screen® system consists of five main services: LISTINGS, SEARCH, RECORDINGS, SCHEDULE, and SETUP. Note: • For the RECORDINGS service to display, an IEEE1394 recording device must be connected to the television (see Chapter 2); otherwise, only four services display. Recording to other devices, such as a VCR, are possible from within the LISTINGS service. • When using the TV Guide On Screen® system to record a program for the first time, it is recommended that you perform a test recording to make sure your system is set up properly. • If the power is cut or the plug becomes disconnected during timer recording, any recorded contents will be lost. • If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the entire TV Guide On Screen® program schedule. It may take up to a week before an entire program schedule is available. Be sure to follow the instructions under “TV Guide On Screen® Reminder” on page 40. LISTINGS screen • When you open the TV Guide On Screen® system, • Use the Number keys on the remote control to jump to a LISTINGS is always the first service displayed. specific channel’s listings. • To watch a show (if on now), highlight the show and press ENTER. • To display the Episode Options panel menu for a particular show, highlight a show and press MENU. • With LISTINGS highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen. Episode Options panel menu From the Episode Options panel menu, you can choose to set a recording, set a reminder, or tune to the channel. The following are descriptions of the buttons. • Use the arrow keys to move the highlight within LISTINGS to do the following: GO TO SERVICE BAR: Closes the menu, changes no information, and returns to the Service Bar. – View eight days of show listings – Read show descriptions TUNE TO CHANNEL / WATCH NOW: Exits the TV Guide On Screen® system and tunes to the channel of the highlighted show (if the show airs in the future) or tunes to the show (if the show is currently airing). The button label changes according to whether the show is currently airing or not. SET RECORDING: Displays the Record Options panel menu, from which you can set the show to record. For additional information, see “SCHEDULE screen” and “Record features” on page 61. – Tune directly to a show currently airing SET REMINDER: Displays the Remind Options panel menu, – Set a show to Remind (e.g., start time, frequency, automatic from which you can set a reminder for the show. For additional power ON, auto-tune TV) information, see “SCHEDULE screen” on page 61 and – Set a show to Record (e.g, start/end time, frequency) “Remind features” on page 63. – Lock and unlock the Video Window CANCEL: Closes the menu, changes no information, and – Access panel ads and channel ads returns to the highlighted show. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 57 HM95_R2_057-62_062705 57 6/27/05, 6:56 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) SEARCH screen • SEARCH allows you to find shows by keyword, Example: Category search alphabetically, or by category (HDTV, Movies, Sports, Children, Educational, News, Variety, Series). 1. From the SEARCH screen, press z to highlight a category (in this example, MOVIES). • With SEARCH highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen. 2. Press z to highlight a subcategory (in this example, ALL). • Use the arrow keys to move the highlight within SEARCH. 3. Press ENTER to display a list of all movies, organized by date and time. 4. Highlight a show and press ENTER to watch (if on now) or press MENU to display the Episode Options panel menu. (See “Episode Options panel menu” on page 57.) Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 58 HM95_R2_057-62_062705 58 6/27/05, 6:56 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) SEARCH screenrf Example: Keyword search 6. A list of all matching shows for that keyword is displayed. Keyword search lets you enter a word(s) to find a particular show by category or for every show title that matches. 1. From the SEARCH screen, highlight KEYWORD, and then press ENTER. 2. Highlight NEW SEARCH in the panel menu, and then press ENTER. 7. Highlight a show and press ENTER to display all airings. Then highlight a specific listing and press ENTER to watch (if on now) or press MENU to display the Episode Options panel menu. From the Episode Options menu, you can choose to set a recording or reminder, or tune to the channel (see “Episode Options panel menu” on page 57.) 3. The Search Options panel menu opens. Highlight CATEGORY, and then use the arrow keys to highlight a category to search (All, HDTV, Children, Sports, etc.). 4. After highlighting a category, press z to highlight ENTER KEYWORD, and then press ENTER. The TV Guide On Screen® system stores all the keywords you create. To edit or delete a keyword: From the SEARCH/KEYWORD screen, highlight the keyword you want to edit or delete, and then press MENU to display the Search Options panel menu, with the 5. The keyboard is displayed. Use the arrow keys to highlight following options: a character and then press ENTER to display it. When – GO TO SERVICE BAR: Closes the menu, changes no finished entering all characters, highlight DONE and press information, and returns to the Service Bar. ENTER. – EDIT SEARCH: Displays the keyboard, from which you can change the keyword. – DELETE SEARCH: Displays the Confirmation panel menu. Select YES to delete the search or NO to close the panel menu. – CANCEL: Closes the panel menu, changes no information, and returns to the highlighted show. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 59 HM95_R2_057-62_062705 59 6/27/05, 6:56 PM

• When using the TV Guide On Screen® system to record a program for the first time, it is recommended that you perform a test recording to make sure your system is set up properly. • If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the entire TV Guide On Screen® program schedule. It may take up to a week before an entire program schedule is available. Be sure to follow the instructions under “TV Guide On Screen® Reminder” on page 40. Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) RECORDINGS screen The RECORDINGS service screen displays a list of previously To view a recording, you can do one of the following: recorded or currently recording shows on an IEEE1394 • Highlight an episode and press ENTER to view it now. The recording device connected to the TV (see Chapter 2). episode either starts from the beginning or from where it Note: RECORDINGS will not appear in the Service Bar unless you was last stopped (if viewed previously). have an IEEE1394 video recording device connected to one of the • Highlight an episode and press MENU to display the IEEE1394 ports on the TV. See Chapter 2 for details. Episode Options panel menu, with the following options: For additional details, see “Record features” on page 61. – GO TO SERVICE BAR: Closes the menu, changes no • With RECORDINGS highlighted in the Service Bar, press information, and returns to the Service Bar. INFO to display a help screen. Press INFO again to close the – RESUME: Starts from the beginning or from where it screen. was last stopped (if viewed previously). – PLAY FROM BEGINNING: Starts from the beginning, even if stopped previously. – DELETE EPISODE: Deletes the episode from the RECORDINGS list and deletes the recording from the IEEE1394 recording device. A Confirm panel menu displays. Press YES to delete the episode or NO to close the panel menu. To choose the way recordings are displayed: – CANCEL: Closes the panel menu, changes no 1. Highlight RECORDINGS on the Service Bar, and press information, and returns to the highlighted show. MENU to display the Recording Options panel menu. 2. Press yz to choose between View As and Sort By, as described below. View As: Press x • to choose between the following: • List—Displays every recorded episode for a show (see example in Screen B, at right). Note: In List view, highlight an episode to display an Info Box with show information. Press MENU to display the Screen A Episode Options panel menu (see “Episode Options panel menu” on page 57). • Group—Displays recorded shows without listing every recorded episode (see example in Screen A, at right). Note: In Group view, highlight a show and press ENTER to view all recorded episodes. Press ENTER again to collapse the episode list. Screen B Sort By: Press x and • to choose between the following: • Title—Displays recorded shows in alphabetical order (see example in Screen A, at right). • Date—Displays recorded shows by date and time, with most recent first (see example in Screen B, at right). The unauthorized recording, use, distribution, or revision of television 3. When finished, press ENTER to highlight DONE, and programs, videotapes, DVDs, and other materials is prohibited under the then press ENTER again to close the panel menu and Copyright Laws of the United States and other countries, and may subject display the recordings with the selected options. you to civil and criminal liability. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 60 HM95_R2_057-62_062705 60 6/27/05, 6:56 PM

est recording (power cord ore an entire Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) SCHEDULE screen Record features The SCHEDULE service screen allows you to review, edit, or You can set a show to Record, or edit the record settings for a delete Record and Remind events you set previously. show, in LISTINGS, SEARCH, and SCHEDULE. There are three ways to set a show to Record, as described below. 1) Set a show to Record using the REC key on the remote control Press the REC key on the remote control to record the show Once with current default settings (start and end recording on time). Each time you press REC, you change the Record frequency (but not the default settings) among Once (default), Regularly, Weekly, and Cancel. • With SCHEDULE highlighted in the Service Bar, press Note: The related Record icon appears on the show tile INFO to display a help screen. Press INFO again to close each time you press REC. See “Record icons,” on page 62. the screen. 2) Set a show to Record from a panel menu 1. Highlight a show and press MENU to display the Episode Options panel menu. 2. Highlight SET RECORDING and press ENTER to display the Record Options panel menu. • Highlight an event and press MENU to display the Schedule Options panel menu, with the following options: – GO TO SERVICE BAR: Closes the menu, changes no information, and returns to the Service Bar. – WATCH NOW: Exits the TV Guide On Screen® system and tunes to the highlighted show. 3. Highlight the FREQUENCY field, and press x or • to – DELETE RECORDING: Removes the recording from choose among Once, Regularly, Weekly, or Off. the schedule. A Confirm panel menu displays. Press YES 4. Highlight the START field, and press x or • to choose to delete the recording or NO to close the panel menu. in the range from 120 minutes early to 120 minutes late – EDIT RECORDING: Opens a menu in which you can or On Time (default = On Time). change existing recording information. 5. Repeat step 4 for the END field. – SET REMINDER: Opens a menu in which you can set a 6. Highlight the RECORDER field and press x or • to reminder for the show (Record is not cancelled). choose the recording device. – CANCEL: Closes the panel menu, changes no Note: For connected IEEE1394 recording devices only. information, and returns to the highlighted show. 7. Highlight the KEEP UNTIL field and press x or • to choose how long you want to keep the Record event. An icon identifies the event type. For more details, see “Record Note: For connected IEEE1394 recording devices only. features,”at right, and “Remind features” on page 63. 8. Press ENTER to highlight SCHEDULE RECORDING, and press ENTER again to close the menu. A Record icon for the selected frequency appears on the show tile. See “Record icons” on page 62. Note: For connected IEEE1394 recording devices only. Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the highlighted show. Note: You can change the default values of the Record Options panel menu fields. See “Change default options” on page 66. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 61 HM95_R2_057-62_062705 61 6/27/05, 6:57 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) Record features (continued) 3) Manually set a show to Record Record conflict 1. Highlight SCHEDULE in the Service Bar, and press A conflict message appears for the following reasons: MENU to display the Schedule Options panel menu. • A show set to Record overlaps with any part of another 2. Highlight NEW MANUAL RECORDING and press show previously set to Record. ENTER to display the Record Options panel menu. • A show set to Record overlaps with a show previously set to Press yzx • to move through the options. auto-tune. (For auto-tune details, see “Remind features” on Press the Number keys or yzx • to change the page 63.) information, as necessary. Select one of these options: 3. Enter the information in the panel menu fields. You will • Record Anyway—This show will override an existing show need to set the start and end time for the recording. For set to Record or auto-tune. details, see “Set a show to Record from a panel menu” on • Don’t Record This Show—Cancels the Recording. the previous page. Note: When setting a Manual Recording, the frequency option “Daily” is available instead of “Regularly.” See “Record icons,” below right, for a description of Record icons. 4. When finished entering the information in the fields, press ENTER to highlight SCHEDULE RECORDING, and press ENTER again to close the menu. A Record icon for the selected frequency appears on the show tile. See “Record Icons,” below right. Note: Manual recording is listed by channel number. Or highlight CANCEL and press ENTER to close the menu, change no information, and return to the Record icons highlighted show. Following is a description of the Record icons that will appear When using the TV Guide On Screen® system to record a on the tile for a show set to Record. program for the first time, it is recommended that you perform a test recording to make sure your system is set • Record Once —Records the show one time. up properly. • Record Regularly —Records the show every time the Recording notification banner show airs on the same channel and starts at the same time. • If the TV is not on, the recording occurs as scheduled. • If the TV is on and you are watching the channel that is set to • Record Weekly —Records the show every time the show record, the recording occurs as scheduled. airs on the same day of the week and on the same channel, and starts at the same time. • If the TV is on and you are watching a channel other than the one that is set to record, a notification banner (illustrated below) appears on-screen before recording starts. At that time • Record Daily —Records on the same channel and at the you can choose to start or cancel recording. same start time every weekday (Monday through Friday). Note: This icon displays for manual recordings only. The default highlighted item in the notification banner is “Change channel; start recording.” If no change is made within 3 minutes, the notification banner will close • Record Suspend —Recording is Suspended due to a automatically, the channel will change to the one set to schedule conflict (show remains in Schedule). record, and the recording will occur as scheduled. If you want to cancel the recording, select “Don’t change; cancel • Record Off —Keeps the Recording in the Schedule list recording” in the notification banner and press ENTER. but will not record this show until the frequency is changed. The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 62 HM95_R2_057-62_062705 62 6/27/05, 6:57 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) Remind features You can set a Reminder to perform the following functions: Or highlight CANCEL and press ENTER to close the • Automatically turn on the TV (if off ) at the scheduled menu, change no information, and return to the reminder time, and tune the TV to the channel of the show highlighted show. for which you set the reminder. 2) Manually set a show Reminder • Automatically tune the TV, at the scheduled reminder time, to the channel of the show for which you set the reminder. 1. Highlight SCHEDULE in the Service Bar, and press MENU to display the Schedule Options panel menu. • Display an on-screen notification banner (reminding you that the show is about to start), from which you can choose to 2. Highlight NEW MANUAL REMINDER and press tune the TV to the show’s channel or cancel the reminder. ENTER to display the Remind Options panel menu. You can set a show reminder, or edit the reminder settings for a Press yzx • to move through the options. show, in LISTINGS, SEARCH, and SCHEDULE. There are Press the Number keys or yzx • to change the two ways to set a show reminder, as described below. information, as necessary. 1) Set a show Reminder from a panel menu 1. Highlight a show and press MENU to display the Episode Options panel menu. 2. Highlight SET REMINDER and press ENTER to display the Remind Options panel menu. 3. Enter the information in the panel menu fields. You will need to set the start and end time for the reminder. For details, see “Set a show reminder from a panel menu,” at left. Note: When setting a Manual Reminder, the frequency option “Daily” is available instead of “Regularly.” See “Remind icons,” on the following page, for a description of Reminder 3. Highlight the FREQUENCY field, and press x or • to icons. choose among Once, Regularly, Weekly, or Off. 4. When finished entering the information in the fields, 4. Highlight the POWER ON TV field, and press x or • press ENTER to highlight SCHEDULE REMINDER, to choose either Yes (to turn on the TV automatically, if and press ENTER again to close the menu. off, at the scheduled Reminder time) or No (default). A Remind icon for the selected frequency appears on the 5. Highlight the AUTO TUNE TV field, and press x or • show tile. See “Remind icons” on the following page. to choose either Yes (to automatically tune the TV to the channel you are setting the Reminder for at the Note: Manual reminders are listed by channel number. scheduled Reminder time; the TV must be on at the Or highlight CANCEL and press ENTER to close the time) or No (default). menu, change no information, and return to the Note: You can change the default values of the Remind highlighted show. Options panel menu fields. See “Change default options” on page 66 for details. 6. Highlight the WHEN field (to set a time for displaying the reminder screen), and press x or • to choose in the range from 15 minutes early to 15 minutes late or On Time (default = 1 minute early). 7. Press ENTER to highlight SCHEDULE REMINDER, and press ENTER again to close the menu. A Remind icon for the selected frequency appears on the show tile. See “Remind icons” on page 64. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 63 HM95_R2_063-66_062705 63 6/27/05, 6:58 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) Remind features (continued) Reminder notification banner Remind icons Based on your option settings, a notification banner will appear Following is a description of the Remind icons that will appear on-screen, if your TV is on at the scheduled Reminder time. on the tile for a show set to Remind. At that time you can either press ENTER to hide the Reminder banner, or highlight the show and press ENTER to tune to • Remind Once —Displays a show reminder one time. the show. If no choice is made within 3 minutes, the notification banner • Remind Regularly —Displays a show reminder every closes automatically and completes the highlighted item (default time the show airs on the same channel and starts at the same is HIDE REMINDERS). time. Note: If more than two reminders are set for the same time, arrows appear on the Reminder notification banner. Press yz • Remind Daily —Displays a show Reminder every to highlight the shows. weekday (Monday through Friday) for the same channel and start time. Note: This icon displays for manual reminders only. • Remind Suspend —Reminder is Suspended due to a schedule conflict (show remains in Schedule). Remind conflict A conflict message appears for the following reasons: • Remind Off —Keeps the Reminder in the Schedule list • A show set with an auto-tune Reminder has the same start but will not display a reminder until you change the time as an existing auto-tune Reminder. frequency. • A show set with an auto-tune Reminder overlaps with a scheduled Recording. Select one of these options: • Auto-Tune Anyway—This show will override an existing show set to auto-tune. • Proceed, No Auto-Tune—Set the show as a Reminder but do not auto-tune. • Don’t Set This Reminder—Cancels the Reminder. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 64 HM95_R2_063-66_062705 64 6/27/05, 6:58 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) SETUP screen After you complete the initial TV Guide On Screen® setup (as Change channel display described in Chapter 5), you can change the following settings: This option allows you to edit channel information that appears • Change system settings in LISTINGS, including the following: • Change channel display • Reorder the position the channels appear in LISTINGS. • Change default options • Change the “tune channel” number. Highlight a choice, press ENTER, and follow the on-screen Note: The “tune channel” is the channel on which you receive instructions. a station. For example, two viewers in the same zip code may receive the same station on different channel numbers, depending on whether they have Cable service or are using a cable box. • Switch a channel to one of the following settings: – On (channel is always displayed in LISTINGS) – Off (channel is never displayed in LISTINGS) – Auto-Hide (channel is displayed in LISTINGS only when program information is available) With SETUP highlighted in the Service Bar, press INFO to display a help screen. Press INFO again to close the screen. 1. From the SETUP screen, highlight CHANGE CHANNEL DISPLAY and press ENTER. Change system settings 2. Highlight the channel row you want to edit and press ENTER to display the Grid Options panel menu. This option appears only after you have completed the initial TV Guide On Screen® setup process (as described in Chapter 5). 1. From the SETUP screen, highlight CHANGE SYSTEM SETTINGS and press ENTER. 3. To edit the options, press INFO and follow the on-screen instructions. 2. Press ENTER again to display the Confirming Your Settings screen. 3. Highlight one of the options, press ENTER, and follow the on-screen instructions. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 65 HM95_R2_063-66_062705 65 6/27/05, 6:58 PM

Chapter 7: Using the TV Guide On Screen® interactive program guide TV Guide On Screen® Services (continued) SETUP screen (continued) Change default options Record defaults This option allows you to change default settings in the 1. From the SETUP screen, highlight CHANGE DEFAULT following categories: OPTIONS and press ENTER. • General Defaults 2. Highlight RECORD DEFAULTS and press MENU to display the Record Defaults panel menu. • Record Defaults • Remind Defaults General defaults 1. From the SETUP screen, highlight CHANGE DEFAULT OPTIONS and press ENTER. 3. Enter the required information in the panel menu fields (start time, end time, recorder choice, how long to keep a Record event, the quality of the recording). See “Record features” on page 61 for details on entering values in these fields. 4. When finished, press ENTER to highlight DONE, and 2. Highlight GENERAL DEFAULTS and press MENU to press ENTER again to close the menu and accept the display the General defaults panel menu. changes (or highlight CANCEL to close the menu with no changes). Remind defaults 1. From the SETUP screen, highlight CHANGE DEFAULT OPTIONS and press ENTER. 2. Highlight REMIND DEFAULTS and press MENU to display the Remind Defaults panel menu. 3. Enter the following information in the panel menu fields: • BOX SIZE: The initial Info Box size when you open the TV Guide On Screen® system. Choices are No, Small (default), Large, and Last Used. • BOX CYCLE: The Info Box size rotation when you press INFO on the remote control when the TV Guide On Screen® system is open. Choices are No Only, Small Only, Large Only, No & Small, No & Large, Small & 3. Enter the required information in the panel menu fields Large, and All (default). (power On TV, auto-tune, when to display the Remind • AUTO GUIDE: Automatic entry into the TV Guide screen). See “Remind features” on page 63 for details on On Screen® system when the TV is powered on. Choices entering values in these fields. are On (default) and Off. 4. When finished, press ENTER to highlight DONE, and Note: Set the AUTO GUIDE to Off if you do not want the press ENTER again to close the menu and accept the TV Guide On Screen® system to open every time you turn changes (or highlight CANCEL to close the menu with on the TV. no changes). 4. When finished, press ENTER to highlight DONE, and press ENTER again to close the menu and accept the changes (or highlight CANCEL to close the menu with no changes). Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 66 HM95_R2_063-66_062705 66 6/27/05, 6:58 PM

8 Using the TV’s features Selecting the video input source to view To select the video input source to view: 1. Press INPUT on the remote control or TV/VIDEO on the TV front panel. 2. Press 0–8 to select the input source you want to view, which will depend on the input terminals you used to connect your devices (see Chapter 2). Numbers The current signal source displays in the top right corner of the Input Selection screen. INPUT Input Selection ANT 1 y 0 ANT 1 1 Video 1 2 Video 2 3 Video 3 z 4 ColorStream HD1 5 ColorStream HD2 6 HDMI 1 7 HDMI 2 8 ANT 2 0 - 8 / INPUT to Select Note: • When the Input Selection screen is open, you also can use the yz buttons on the remote control (or the Channel yz buttons on the front panel) to change the input, or you can repeatedly press INPUT on the remote control or TV/VIDEO on the TV front panel to change the input. Remote control • To select an IEEE1394 input source, press the TheaterNet DEVICE button on the remote control (see page 26 and 45). • If an IEEE1394 device is the current input, it will appear at the TV/VIDEO bottom of the Input Selection list; however, it will not display in the CHANNEL zy list if you change the input source. { TV front touchpad • You can label the video input sources according to the specific *The MENU devices you have connected to the TV (see “Labeling the video button input sources” on the next page). functions as • The source can be “hidden.” See page 68 for details. the ENTER (ENTER)* button when a menu is on-screen. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 67 HM95_R2_067-78_061505 67 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Labeling the video input sources You can label each video input source according to the type of 4. Press x or • to select the desired label for that input source. device you connected to each source, from the following preset If a particular input is not used, you can select “Hide” as list of labels: the label, which will cause that input to be “grayed out” in the input list and skipped over when you press the INPUT – – (default label) button on the remote control. Hide (to hide an unused input in the Input Selection Note: If you select “Hide” for all of the input labels, the POP window) feature will be disabled. If you then attempt to access the POP Audio Receiver feature, the message “Not available” will appear on-screen. VCR 5. To save the new input labels, highlight Done and press Video Recorder ENTER. To revert to the factory default labels, highlight Laser Disk Reset and press ENTER. Compact Disc Input labeling example: DVD DTV The screen below left shows the default Input Selection screen (with none of the inputs labeled). The screen below right is an Satellite/DSS example of how you could label the inputs if you had connected Cable a DVD player to VIDEO 1, Cable TV to VIDEO 2, an audio Game Console receiver to VIDEO 3, a video recorder to ColorStream HD1, a Note: DTV set-top box to HDMI 1, and a satellite/DSS set-top box to • If you set up devices in TheaterNet,™ the associated inputs are HDMI 2. Also note that the ColorStream HD2 input is labeled automatically labeled and cannot be relabeled until you remove the “Hidden,” which means that the input will be skipped over device from TheaterNet (see page 45). when INPUT or TV/VIDEO is pressed. • If you set up a cable box in VIDEO 1, that input will be labeled automatically and cannot be relabeled until you remove the device Input Selection ANT 1 Input Selection ANT 1 from the TV Guide On Screen® setup. 0 ANT 1 0 ANT 1 • You cannot select IEEE1394 devices through the Input Selection 1 Video 1 1 DVD 2 2 window; however, you can select and control IEEE1394 devices Video 2 Cable 3 Video 3 3 Audio Receiver through TheaterNet (see page 45). 4 ColorStream HD1 4 Video Recorder 5 ColorStream HD2 5 ColorStream HD2 (Hidden) 6 HDMI 1 6 DTV To label the video input sources: 7 HDMI 2 7 Satellite/DSS 8 ANT 2 8 ANT 2 1. Press MENU and open the Preferences menu. 0 - 8 / INPUT to Select 0 - 8 / INPUT to Select 2. Highlight Input Labeling and press ENTER. Input Selection screen Input Selection screen with 3. Press y or z to highlight the video source you want to with no inputs labeled all inputs labeled except input 5, label. which has been hidden. To clear the input labels: Preferences Favorite Channels 1. Press MENU and open the Preferences menu. Closed Caption Mode Off Closed Caption Advanced 2. Highlight Input Labeling and press ENTER. Input Labeling Menu Language English 3. Highlight Reset and press ENTER. Home CH Setup 4. Highlight Done and press ENTER. Navigate Select CH RTN Back EXIT Exit Note: If you set up a device in TheaterNet, its input label will Input Labeling not be cleared unless you remove the device from TheaterNet Video 1 DVD (see page 45). Video 2 Cable Video 3 Audio Receiver ColorStream HD 1 Video Receiver ColorStream HD 2 Hide HDMI 1 DTV HDMI 2 Satellite/DSS ANT 2 -- Reset Done Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 68 HM95_R2_067-78_061505 68 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Tuning channels Using the channel browser The channel browser stores the most recently viewed channels (up to 32) in the channel history. This feature allows you to: • Keep a separate, temporary* history of the last 32 channels tuned from each of three inputs: ANT 1, ANT 2, and Cable Box. *Turning off the TV will clear the channel history for all three inputs. • Quickly surf and tune your recently viewed channels from the channel browser banner (illustrated below). • Surf via Browse mode (to immediately tune channels as you highlight them in the channel browser banner) or Select mode (to surf over channels in the browser banner before you select one to tune). • Set a “HOME” channel for the ANT 1, ANT 2, and Cable Box inputs. To open the channel browser banner: Press x ( ) or • ( ) on the remote control. – Press x ( ) to surf back from the most recently viewed channel through the last 32 channels that were tuned from the current input, which are automatically stored in the channel history for the current input (ANT 1, ANT 2, or Cable Box only). – Press • ( ) to surf forward from the previous channels in the channel history up to the most recently viewed channel. Elements of the channel browser banner Active channel Highlighted channel Channels stored Active channel Home channel instructions status (Displays with a yellow in the channel (In Browse mode, because the highlighted [Press x ( ) or • ( ) (Displays in this area background in Select mode. history channel is tuned automatically, the active to surf the other channels only if available.) Displays with a yellow channel and the highlighted channel in the channel history.] outline in Browse mode.) will always be the same.) 12-3 14 26-1 17-2 3 Hold HOME key 12345678 ABCD-DTV QRS TUV XYZ 3 sec to program CB Select Mode ANT 1 CABLE 3 XYZ 480p 17-2 Current mode Current Current Active Channel call Resolution Home channel (Select or Browse) input antenna type channel letters (cable or TV) number (if available) To toggle between Browse mode and Select mode: After opening the channel browser banner, press y or z to toggle between Browse mode and Select mode. The “Current mode” field on the channel browser banner will flash green. Note: The channel browser banner opens in Browse mode by default. To tune to a channel in Browse mode: To tune to a channel in Select mode: 1. While watching TV, press x ( ) or •( ) to open the 1. While watching TV, press x ( ) or •( ) to open the channel browser banner and surf back to a previous channel channel browser banner and surf back to a previous channel or forward to the next channel in the channel history. or forward to the next channel in the channel history. In Browse mode, when you stop on a channel number in In Select mode, when you stop on a channel number in the browser banner, it will be highlighted with a yellow the browser banner, it will be highlighted with a yellow outline and the TV will automatically tune to the channel. background but the TV will not automatically tune to the 2. Press EXIT to close the channel browser banner. channel. 2. Press ENTER to tune the TV to the highlighted channel. 3 2 102-1 Hold HOME key 3 sec to program 3. Press EXIT to close the channel browser banner. Browse Mode ANT 1 CABLE Ch.102-1 1080i Ch.3 3 2 102-1 Hold HOME key 3 sec to program In Browse mode, the highlighted channel number is outlined Select Mode ANT 1 CABLE Ch.102-1 1080i Ch.3 in yellow and the channel will be tuned to automatically. In Select mode, the highlighted channel number has a yellow background. Press ENTER to tune to the channel. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 69 HM95_R2_067-78_061505 69 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Tuning channels (continued) Using the channel browser (continued) Adding and clearing channels in the Setting a channel as the “Home” channel channel history for an input Adding channels to the channel history To set a channel as Home using the remote control: The channel browser automatically creates a history of the 1. Tune the TV to the channel you would like to set as the last 32 channels that were tuned in the current input (ANT 1, Home channel for the current antenna input. ANT 2, and Cable Box inputs only). A separate history will be 2. Press and hold the HOME ( ) button on the remote stored for each of these inputs. control for 3 seconds. When the Home channel is saved, If you change the input you are viewing: the channel browser banner will appear at the bottom of the screen with the home icon flashing green. a) you will begin a channel history for that input if one did not exist; or Note: You can set a different Home channel for each input (ANT 1, ANT 2, and Cable Box inputs only). b) you will return to the existing channel history for that input if one had already been started. To set a channel as Home using the menus: The channel browser will store the following channels: 1. Press MENU and open the Preferences menu. • All channels that are tuned using the numeric buttons on the 2. Highlight Home CH Setup and press ENTER. The Home remote control. CH Setup window will display. • All channels that are tuned for at least 7 seconds using the Home CH Setup CH yz buttons or the Fav CH y z buttons on the remote ANT 1 -- control. ANT 2 -- Cable Box -- Note: • The channel browser banner will not appear when the POP double Reset Done window is open; however, channels tuned while the POP double window is open will be added to the channel browser history for the Note: "Cable Box" will appear in the Home CH Setup current input. window only if you connected a cable box to your TV. • The channel browser banner will not appear in the FAV SCAN 3. Use the y z buttons to select the input for which you (favorite scan) multi-window. Channels that appear in the FAV SCAN multi-window will not be added to the channel browser history; want to set the Home channel. however, channels that are tuned from the FAV SCAN multi-window 4. Use the numeric and dash (–) buttons on the remote for at least 7 seconds will be added to the channel history. control to enter the desired Home channel for each input. 5. To save your entries, highlight Done and press ENTER. Clearing channels from the channel history To clear your entries, highlight Reset and press ENTER. • Turning off the TV will clear all three channel histories (ANT 1, ANT 2, and Cable Box). To tune to the Home channel: • Removing the CableCARD™ will clear the channel history While an input that has a set for the ANT 1 input. Home channel is active, press the • Reconfiguring the ANT 1, ANT 2, or Cable Box input HOME ( ) button on the will clear the channel history for the newly configured remote control. input(s). Note: If you press the HOME Note: See page 41 for details on configuring the antenna inputs. button while an input other than an antenna or Cable Box input is x /BACK selected, the TV will tune to the •/NEXT most recently tuned Home channel and input. HOME ( ) Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 70 HM95_R2_067-78_061505 70 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Tuning channels (continued) Tuning your favorite channels Switching between two channels using To tune to the channels you programmed as Favorite Channels, Channel Return see page 44. The Channel Return feature allows you to switch between two channels without entering an actual channel number each time. Tuning to the next programmed channel 1. Select the first channel you want to view. To tune to the next programmed channel: 2. Select a second channel using the Channel Number buttons (and the dash (–) button if selecting a digital channel). Press CHANNEL y or z on the remote control or TV front panel. 3. Press CH RTN on the remote control. The previous channel will display. Each time you press CH RTN, the TV Note: will switch back and forth between the last two channels • This feature will not work unless you program channels into the that were selected. TV’s channel memory (see page 42). Note: • If you are recording a digital channel, you will only be able to • If you press CH RTN from a non-antenna input, the TV will change analog channels while the recording is in progress. If you return to the last-viewed ANT input and channel. are recording an analog channel, you will only be able to change • If you are currently recording a program, this feature will not digital channels while the recording is in progress. This is be available. because the TV tuner that is being recorded (digital or analog) will be locked on the channel that is currently recording. Switching between two channels using Tuning to a specific channel SurfLock™ (programmed or unprogrammed) The SurfLock™ feature temporarily “memorizes” one channel in the CH RTN button, so you can return to that channel quickly Tuning analog channels: from any other channel by pressing CH RTN. Press the Channel Number buttons (0–9) on the remote To memorize a channel in the CH RTN button: control. For example, to select channel 125, press 1, 2, 5. 1. Select the channel you want to program into the CH RTN Tuning digital channels: button. Press the Channel Number buttons (0–9) on the remote 2. Press and hold CH RTN for about 2 seconds until the control, followed by the – (dash) button and then the sub- message “Channel Memorized” appears on the screen. The channel has been programmed into the CH RTN button. channel number. For example, to select digital channel 125-1, press 1, 2, 5, –, 1. 3. You can then change channels repeatedly, and when you Note: If a digital channel is not programmed—either through press press CH RTN, the memorized channel will be the automatic channel scan (page 42) or the channel add/ selected. delete function (page 43)—you will have to tune the RF The TV will return to the memorized channel one time only. channel using the Channel Number and Dash buttons on the Once you press CH RTN and then change channels again, the remote control. CH RTN memory will be cleared and the button will function as Channel Return, by switching back and forth between the last two channels that were selected. Channel Numbers — (dash) CHANNEL yz CH RTN Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 71 HM95_R2_067-78_062705 71 6/27/05, 8:06 PM

Chapter 8: Using the TV’s features Selecting the picture size You can view many program formats in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, and Full—as described below and on the next page. The way the image displays in any of the picture sizes will vary Numbers depending on the format of the program you are viewing. Select the picture size that displays the current program the way that PIC SIZE looks best to you. Your picture size preferences can be saved for each input on your TV. y To select the picture size: z 1. Press PIC SIZE on the remote control. 2. While the Picture Size menu is on-screen, press the corresponding number button (0–4) to select the desired picture size. Note: Picture Size You also can select the picture size using the 0 Natural 1 TheaterWide 1 menu system. Select Picture Size in the 2 TheaterWide 2 Video/Theater Settings menu. Select the input 3 TheaterWide 3 for which you want to save your picture size 4 Full settings. To save your settings, highlight Done 0 - 4 / PIC SIZE to Select and press ENTER. Note: Theater Settings • You also can repeatedly press PIC SIZE to select the desired Picture Size Natural Picture Scroll -- picture size (or press the yz buttons on the remote control Cinema Mode Film while the Picture Size screen is open). Auto Aspect Ratio On • “Full” may not be available for some program formats (it will Reset Done be “grayed out” in the Picture Size screen). Natural picture size • The image is displayed close to its originally formatted proportion. Some program formats will display with sidebars and/or bars at the top and bottom. Natural picture size example: The way the image displays will vary depending on the format of the program you are currently watching. Conventional picture on a Conventional picture in Natural size on conventional TV screen your wide-screen TV Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 72 HM95_R2_067-78_061505 72 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Selecting the picture size (continued) TheaterWide 1 picture size (For 4:3 format program) Note: • The center of the picture remains close to its • If you select one of the TheaterWide® picture sizes, the top and bottom edges of the original proportion, but the left and right picture (including subtitles or captions) may edges are stretched wider to fill the screen. be hidden. To view the hidden edges, either scroll the picture (TheaterWide 2 and 3 only) or try viewing the program in Full or Natural picture size. • When selecting the picture size, the way the image displays will vary depending on the format of the program you are currently watching. TheaterWide 1 picture size example TheaterWide 2 picture size (for letter box programs) Using these functions to change the picture size (i.e., changing the height/ • The picture is stretched wider to fill the width width ratio) for any purpose other than of the screen, but only slightly stretched taller. your private viewing may be prohibited • The top and bottom edges of the picture are under the Copyright Laws of the United hidden. To view the hidden areas, see ABCDEFG---------------- States and other countries, and may “Scrolling the TheaterWide® picture” on page subject you to civil and criminal liability. 74. TheaterWide 2 picture size example TheaterWide 3 picture size (for letter box programs with subtitles) • The picture is stretched wider to fill the width of the screen, but only slightly stretched taller. • The top and bottom edges are hidden. To view the hidden areas (such as subtitles or captions), ABCDEFG---------------- see “Scrolling the TheaterWide® picture” on page 74. ABCDEFG-------------------------- TheaterWide 3 picture size example Full picture size (for 16:9 [480i, 480p] source programs only) • If receiving a squeezed 4:3 format program, the picture is stretched wider to fill the width of the screen, but not stretched taller. • None of the picture is hidden. Full picture size example Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 73 HM95_R2_067-78_061505 73 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Scrolling the TheaterWide® picture Using the auto aspect ratio feature (TheaterWide 2 and 3 only) When the auto aspect ratio feature is set to On, the picture size is automatically selected when one of the following input You can set separate scroll settings for the TheaterWide 2 and sources is received: TheaterWide 3 modes for each input. • A 480i signal from the VIDEO 1, VIDEO 2, VIDEO 3, To set the scroll settings: ColorStream HD-1, or ColorStream HD-2 input. 1. Press INPUT on the remote control or TV/VIDEO on the • A 1080i, 480i, 480p, or 720p signal from the HDMI input. TV to select the input for which you want to set the picture Automatic aspect size size and scroll settings. Aspect ratio (automatically selected of signal source 2. Press MENU and open the Video menu. when Auto Aspect is On) 3. Highlight Theater Settings and press ENTER. 4:3 normal Natural (with sidebars) 4:3 letter box TheaterWide 2 16:9 full Full Video Not defined Picture Settings (no ID-1 data or User-selected picture size Advanced Picture Settings Theater Settings HDMI aspect data) (see pages 72–73) Note: • The auto aspect ratio feature is not applicable to antenna or Cable input Navigate Select CH RTN Back EXIT Exit sources. 4. In the Picture Size field, select either TheaterWide 2 or • The Auto Aspect Ratio feature is not available when the POP double- TheaterWide 3 (you cannot scroll in any other mode). window is open, the Freeze mode is active, or the TV Guide On Screen® system is open. 5. Press z to highlight the Picture Scroll field. 6. Press x or • to scroll the picture up and down as needed, To turn on the auto aspect ratio feature: from –10 to +20. 1. Press MENU and open the Video menu. 2. Highlight Theater Settings and press ENTER. Video Picture Settings Advanced Picture Settings Theater Settings 7. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER. Navigate Select CH RTN Back EXIT Exit 3. In the Auto Aspect Ratio field, select On. 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER. Theater Settings Picture Size Natural Picture Scroll -1 Cinema Mode Film Auto Aspect Ratio On Reset Done To turn off the auto aspect ratio feature: Select Off in step 3 above. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 74 HM95_R2_067-78_061505 74 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Selecting the cinema mode Selecting the lamp mode (480i signals only) You can select either the High Bright or Low Power lamp mode. • The High Bright mode is useful when additional picture When you view a DVD (480i signal; 3:2 pulldown processed) brightness is desired (such as in a bright room). from a DVD player connected to the VIDEO 1, VIDEO 2, ColorStream HD1/HD2 (component video), or HDMI inputs • The Low Power mode reduces wear on the projection lamp. on the TV, smoother motion can be obtained by setting the Using this mode should result in longer lamp life. Cinema Mode to Film. See “Lamp unit replacement” on page 103–105. To set the Cinema Mode to Film: To select the lamp mode: 1. Press MENU and open the Video menu. 1. Press MENU and open the Video menu. 2. Highlight Theater Settings and press ENTER. 2. Highlight Advanced Picture Settings and press ENTER. Video Video Picture Settings Picture Settings Advanced Picture Settings Advanced Picture Settings Theater Settings Theater Settings Navigate Select CH RTN Back EXIT Exit Navigate Select CH RTN Back EXIT Exit 3. In the Cinema Mode field, select Film. 3. In the Lamp Mode field, select High Bright or Low Power, Theater Settings whichever you prefer. Picture Size Natural Advanced Picture Settings ANT 1 Picture Scroll -1 Dynamic Contrast On Cinema Mode Film MPEG Noise Reduction Low Auto Aspect Ratio On CableClear Auto Reset Done Color Temperature Cool Lamp Mode Low Power 4. To save the new settings, highlight Done and press Reset Done ENTER. To revert to the factory defaults, highlight Reset and press ENTER. 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset To set the Cinema Mode to Video: and press ENTER. Select Video in step 3 above. Note: If you set the lamp mode to Low Power, each time you turn on the TV, the lamp will start out in High Bright mode but will switch to Low Power mode in approximately 1 minute. You will notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 75 HM95_R2_067-78_061505 75 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Using the POP features Using the POP double-window feature Note: The POP (picture-out-picture) double-window feature splits the screen into two • When the main window is in the ANT1 or ANT2 windows so you can watch two programs at the same time. mode, the ANT1 and ANT2 inputs cannot be To display a program in the POP window: selected for the POP window. 1. Select the program you want to watch in the main window. • When the main window is in Video 1/2/3, ColorStream HD1/HD2, HDMI 1, or HDMI 2 2. Press SPLIT to open the POP double-window. mode, those inputs cannot be selected for the POP POP double-window window. • You cannot view IEEE1394 source programs in the POP window. • You cannot view two video or two antenna sources in both the main and POP windows simultaneously. Main window POP window (You can view a video source in one window and an antenna source in the other.) ANT1 POP TV12 Video1 • The FREEZE feature is not available when the POP double-window is open. If you press FREEZE when the double-window is open, the message “Not available” will appear. Green border (denotes active window) 3. Press • to highlight the POP (right) window. When highlighted, the window will have a green border. 4. Press INPUT to open the POP Input Selection window. Select the input source for the POP window by pressing the corresponding Number button (0–8). The Numbers current source displays in purple in the POP Input Selection window. INPUT POP Input Selection 0 ANT 1 1 Video 1 2 Video 2 • 3 Video 3 4 ColorSteram HD1 5 ColorSteram HD2 ENTER 6 HDMI 1 7 HDMI 2 8 ANT 2 0 - 8 / INPUT to Select To close the POP window and tune to the highlighted window: SPLIT Press ENTER after highlighting the window you want to view as a normal picture. To close the POP window: Press SPLIT or EXIT. Notes about recording: • If the POP window is open and you attempt to start recording, the POP window will close and recording will start. • If you use the TV’s remote control to start recording, you will not be able to open the POP window and the message “Not Available” will appear on-screen. • It is recommended that you use the TV’s remote control to start recording. If you use a device other than the TV’s remote control to start recording, you may be able to open the POP window during the recording process. If this happens, the recorded audio will reflect the audio of the active window (main or POP), which may not be the audio you intended to record. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 76 HM95_R2_067-78_061505 76 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Using the POP features (continued) Switching the speaker audio (main or POP) While the POP window is open, press x or • to switch the sound (main or POP) that is output from the TV speakers (and from the VARIABLE AUDIO OUT terminals). The window with the active sound is outlined with a green border for 15 seconds. Example: Press x Example: Press • x• POP double-window aspect ratio The POP double-window feature displays each picture according to its input signal aspect ratio, as illustrated in the examples below. 480i 480i 480p/720p/1080i 480i Note: • The Auto Aspect Ratio feature (page 74) does not operate in POP double-window mode. • Aspect ratio is the ratio of width to height of the picture. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 77 HM95_R2_067-78_061505 77 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Using the FREEZE feature 1. When viewing the TV, press FREEZE to make the picture a still picture. 2. To return to the moving picture, either press FREEZE again, press EXIT, change the channel, or change the input. Using the FREEZE function for any Note: purpose other than your private viewing • The FREEZE feature is not available when the POP double-window or FAV SCAN may be prohibited under the Copyright multi-window is open. If you press FREEZE when either window is open, the message Laws of the United States and other “Not available” will appear. countries, and may subject you to civil and criminal liability. • If the TV is left in FREEZE mode, after 15 minutes it will automatically release the FREEZE mode and return to the moving picture. y x • z Moving picture Still picture ENTER EXIT Using the favorite channel scan feature FREEZE You can use this feature to quickly scan and tune the channels you programmed as FAV SCAN favorite channels from a nine-picture multi-window. Note: To use the favorite channel scan feature, you must first program channels into the favorite channel memory. See “Programming your favorite channels” on page 44. To scan and tune your favorite channels: 1. Press FAV SCAN. The TV will display the channels you programmed as favorite channels for the current ANT input in a nine-picture multi-window. (To display the channels you programmed as favorite channels for the other input, you must change antenna inputs first (page 67), and then press FAV SCAN.) 1 2 3 2 4–1 4–2 4 5 6 6 11 13 7 8 9 CABLE 18 18 31 36 2. Highlight the window for the channel you want to view: • Either... press the channel’s multi-window position number (1–9, as illustrated above, and not the actual channel number) to highlight the window; • or... use the y z x • buttons to highlight the window. The highlighted window will display as a moving picture. 3. Press ENTER to tune the TV to the highlighted channel and close the multi-window. 2 4–1 4–2 6 11 13 18 31 36 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 78 HM95_R2_067-78_061505 78 6/27/05, 4:32 PM

Chapter 8: Using the TV’s features Adjusting the picture Selecting the picture mode Adjusting the picture quality You can select your desired picture settings from four picture You can adjust the picture quality (contrast, brightness, color, modes, as described below. tint, and sharpness) to your personal preferences. Mode Picture Quality Selection x Pressing • Sports Bright and dynamic picture (factory setting) contrast lower higher Standard Standard picture settings (factory setting) brightness darker lighter Movie Lower contrast for darkened room (factory setting) color paler deeper Preference Your personal preferences tint reddish greenish sharpness softer sharper To select the picture mode: To adjust the picture quality: Press PIC MODE on the remote control. The following popup menu appears on- 1. Press MENU and open the Video menu. screen. 2. Highlight Picture Settings and press ENTER. Picture Settings Mode: Standard Mode Standard Repeatedly press PIC MODE to cycle Video Picture Settings among the modes. PIC Advanced Picture Settings MODE Theater Settings To select the picture mode using the menu system: Picture Settings ANT 1 1. Press MENU and open the Video menu. Mode Sports Contrast 100 2. Highlight Picture Settings and press ENTER. Brightness 50 Color 50 Tint 0 Sharpness 50 Reset Done Video Picture Settings Advanced Picture Settings 3. Press y or z to select the picture quality you want to adjust Theater Settings (Contrast, Brightness, Color, Tint, or Sharpness), and then x and • to adjust the setting, as described in the table Picture Settings ANT 1 Mode Sports above. Contrast 100 Picture Settings Mode: Preference Brightness 50 Sharpness 70 Color 50 Tint 0 Sharpness 50 4. To save the new settings, highlight Done and press Reset Done ENTER. To revert to the factory defaults, highlight Reset and press ENTER. 3. Press z to highlight the Mode field, and then x • to select the mode you prefer. The picture qualities you adjusted are automatically saved in the Preference mode (see “Selecting the picture mode,” above left). Picture Settings Mode: Standard Mode Standard 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER. Note: • The picture mode you selected is for the current input selection only (ANT 1 in the example above). You can select a different picture mode for each input selection. • If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then change a picture quality setting (for example, increase the contrast or change the color temperature), the picture mode automatically changes to Preference in the Picture Settings menu. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 79 HM95_R2_079-86_061505 79 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Adjusting the picture (continued) Using CableClear™/DNR (digital noise Selecting the color temperature reduction) You can change the quality of the picture by selecting from three preset color temperatures (cool, medium, and warm), as The CableClear™/DNR digital noise reduction feature allows described below. you to reduce visible interference in your TV picture. This may be useful when receiving a broadcast with a weak signal Mode Picture Quality (especially a Cable channel) or playing a noisy video cassette cool blueish or disc. This feature is enabled for 480i signals only. medium neutral NOTE: The CableClear™/DNR feature does not function in warm reddish ColorStream, HDMI (DVI), ATSC, IEEE1394, and digital Cable modes. To select the color temperature: To select CableClear/DNR preferences: 1. Press MENU and open the Video menu. 1. Press MENU and open the Video menu. 2. Highlight Advanced Picture Settings and press ENTER. 2. Highlight Advanced Picture Settings and press ENTER. 3. Press z to highlight the Color Temperature field, and then press x or • to select the mode you prefer (Cool, Medium, 3. Press z to highlight the CableClear/DNR field, and then or Warm). press x or • to make a selection. Video Video Picture Settings Picture Settings Advanced Picture Settings Advanced PictureSettings Advanced Picture Settings Theater Settings Theater Settings Advanced Picture Settings ANT 1 Advanced Picture Settings ANT 1 Dynamic Contrast On Dynamic Contrast On MPEG Noise Reduction Low MPEG Noise Reduction Low CableClear Auto CableClear Auto Color Temperature Cool Color Temperature Cool Lamp Mode Low Power Lamp Mode Low Power Reset Done Reset Done Note: 4. To save the new settings, highlight Done and press • If the current input is Antenna, Video 1, Video 2, or Video 3, ENTER. To revert to the factory defaults, highlight Reset the menu will display the text “CableClear.” The available and press ENTER. selections are Off, Low, Middle, High, and Auto. Note: If you select one of the factory-set picture modes (Sports, • If the current input is ColorStream HD1, ColorStream HD2, or Standard, or Movie) and then change the color temperature, the HDMI, and the video resolution is 480i, the menu will display picture mode automatically changes to Preference in the Picture the text “DNR.” The available selections are Off, Low, Middle, Settings menu. High, and Auto. Auto will react proportionally to the strength of the noise. Low, Middle, and High will reduce the noise in varying degrees from lowest to highest, respectively. • If the current input is ColorStream HD1, ColorStream HD2, or HDMI, and the video resolution is not 480i, the menu will display the text “DNR” and will be “grayed out” with “Off” selected. 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 80 HM95_R2_079-86_061505 80 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Adjusting the picture (continued) Using MPEG noise reduction Using dynamic contrast The MPEG noise reduction feature allows you to reduce When dynamic contrast is set to “On,” the TV will detect visible interference caused by MPEG compression. Choices changes in the picture quality that affect the appearance of your for MPEG noise reduction are High, Medium, Low and Off. contrast settings and automatically adjust the video. Off is automatically selected when this feature is disabled When dynamic contrast is set to “Off,” the settings selected in (“grayed out”). the Contrast field in Picture Settings will be used. To select the MPEG noise reduction level: To select dynamic contrast preferences: 1. Press MENU and open the Video menu. 1. Press MENU and open the Video menu. 2. Highlight Advanced Picture Settings and press ENTER. 2. Highlight Advanced Picture Settings and press ENTER. 3. Press z to highlight the MPEG Noise Reduction field, and 3. Press z to highlight the Dynamic Contrast field, and then then press x or • to make a selection. press x or • to select either On or Off. Video Video Picture Settings Picture Settings Advanced Picture Settings Advanced Picture Settings Theater Settings Theater Settings Advanced Picture Settings ANT 1 Advanced Picture Settings ANT 1 Dynamic Contrast On Dynamic Contrast On MPEG Noise Reduction Low MPEG Noise Reduction Low CableClear Auto CableClear Auto Color Temperature Cool Color Temperature Cool Lamp Mode Low Power Lamp Mode Low Power Reset Done Reset Done 4. To save the new settings, highlight Done and press 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset ENTER. To revert to the factory defaults, highlight Reset and press ENTER. and press ENTER. Note: If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then set the dynamic contrast to “On,” the picture mode automatically changes to Preference in the Picture Settings menu. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 81 HM95_R2_079-86_061505 81 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Using the closed caption mode The closed caption mode has two options: Advanced closed captions • Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are You can customize the closed caption display characteristics by closed captioned (usually marked “CC” in program guides). changing the background color and the text size, type, edge, and color. • Text—An on-screen display of information not related to the current program, such as weather or stock data (when Note: provided by individual stations). • This feature is available for digital channels only. • You cannot set the Caption To view captions or text: Text and Background as the 1. Press MENU and open the Preferences menu. same color. Preferences 2. Highlight Closed Caption Mode and then press • to open To customize the closed Favorite Channels Closed Caption Mode CC1 the menu sidebar. captions: Closed Caption Advanced Input Labeling 3. Press z to highlight the desired closed caption mode and 1. Press MENU and open Menu Language English Home CH Setup then press ENTER. the Preferences menu. 2. Highlight Closed Navigate Select CH RTN Back EXIT Exit Preferences Caption Advanced and Favorite Channels Off press ENTER. Closed Caption Mode Off CC1 Closed Caption Advanced Input Labeling CC2 CC3 3. Press y or z Advanced Closed Captions Menu Language English CC4 to highlight Caption Size Auto Home CH Setup T1 T2 the Caption Text Type Auto Navigate Select CH RTN Back EXIT Exit characteristic Caption Text Edge Auto Caption Text Color Auto you want to Background Color Auto • To view captions: change, and Highlight CC1, then press x Reset Done CC2, CC3, or or • to select CC4. (CC1 displays the format for that characteristic. translation of the 4. To save the new settings, highlight Done and press primary language in ENTER. To revert to the factory defaults, highlight Reset your area.) and press ENTER. Giant pandas eat leaves. Note: If the program or video Caption Size Auto, Small, Standard, Large you selected is not closed captioned, no captions will display Caption Text Type Auto, Default, Mono w/serif, Professional on-screen. w/serif, Mono w/o serif, Proper w/o serif, Casual, Cursive, Small capitals • To view text: Highlight T1, T2, Caption Text Edge Auto, None, Raised, Depressed, Uniform, T3, or T4. Left drop shadow, Right drop shadow Note: If text is not Caption Text Color Auto, Black, White, Red, Green, Blue, available in your WORLD WEATHER Yellow, Magenta, Cyan Temps Current area, a black LONDON F 51 C 11 Weather Clear Background Color Auto, Black, White, Red, Green, Blue, rectangle may MOSCOW PARIS 57 53 14 12 Cloudy Clear Yellow, Magenta, Cyan ROME 66 19 Cloudy appear on your TOKYO 65 18 Rain screen. If this happens, turn the Closed Caption Mode OFF. • To turn off the Closed Caption mode: Highlight OFF. Note: A closed caption signal may not display in the following situations: • When a videotape has been dubbed • When the signal reception is weak • When the signal reception is non-standard Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 82 HM95_R2_079-86_061505 82 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Using the closed caption mode (continued) Digital closed captions You can use the Digital CC/Audio selector to select digital closed caption services (if available), which will temporarily override closed captions for digital channels only. When such services are not available, the Digital CC/Audio selector presents a default list of services. If the selected service is not available, the next best service will be used instead. To select digital closed captions: 1. Press MENU and open the Applications menu. Applications TV Guide On Screen Audio Player Picture Viewer Digital CC/Audio Selector CableCARD Navigate Select CH RTN Back EXIT Exit 2. Highlight Digital CC/Audio Selector and press ENTER. 3. Press y or z to select Closed Caption, and then press x or • to select the desired service. Audio CC 1 Closed Caption Service 1 4. Press ENTER. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 83 HM95_R2_079-86_061505 83 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Adjusting the audio Muting the sound Selecting stereo/SAP broadcasts Press MUTE to partially reduce (1/2 MUTE) or turn off The multi-channel TV sound (MTS) feature allows you to (MUTE) the sound. Each time you press MUTE, the mute output high-fidelity stereo sound. MTS also can transmit a mode will change in the following order. second audio program (SAP) containing a second language, music, or other audio information (when provided by individual → 1/2 Mute → Mute → Volume → stations). If the closed caption mode is set to OFF when you select The MTS feature is not available when the TV is in VIDEO “MUTE” mode, the closed caption feature is automatically mode. When the TV receives a stereo or SAP broadcast, the activated. To mute the audio without automatically activating word “STEREO” or “SAP” appears on-screen when RECALL is the closed caption feature, use the VOL z button to set the pressed. volume to 0. See “Using the closed caption mode” on page 82 To listen to stereo sound: for more information on closed caption modes. 1. Press MENU and open the Audio menu. 2. Highlight Audio Setup and press ENTER. Audio VOL z Audio Settings Advanced Audio Settings RECALL Audio Setup MUTE 3. Press z to highlight the MTS field, and then press x or • Using the digital audio selector to select Stereo. Audio Setup You can use the Digital CC/Audio selector to conveniently MTS Stereo switch between audio tracks on a digital channel (for those Language English Speakers On channels that have multiple audio tracks). This temporarily Optical Output Format Dolby Digital overrides the audio track chosen by the language option under Reset Done Audio Setup. 1. Press MENU and open the Applications menu. 4. To save the new settings, highlight Done and press ENTER. To reset the settings to the factory defaults, 2. Highlight Digital CC/ highlight Reset and press ENTER. Audio Selector and press ENTER. Applications Note: TV Guide On Screen • You can leave the TV in Stereo mode because it automatically 3. Press y or z to select Audio Player Picture Viewer outputs the type of sound being broadcast (stereo or monaural). Audio, and then press x Digital CC/Audio Selector or • to select the desired CableCARD • If the stereo sound is noisy, select MONO to reduce the noise. service. To listen to an alternate language on an ATSC digital station Navigate Select CH RTN Back EXIT Exit (if available): Audio CC 1 Highlight the Language field in step 3 above, and then press Closed Caption Service 1 x or • to select the language you prefer. 4. Press ENTER. To listen to a second audio program on an analog station (if available): Select SAP in step 3 above. Note: • A second audio program (SAP) can be heard only on those TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program’s normal audio. • If you have SAP on and the station you are watching is not broadcasting a second audio program, the station’s normal audio will be output. However, occasionally there is no sound at all in SAP mode. If this happens, set the MTS feature to Stereo mode. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 84 HM95_R2_079-86_061505 84 6/27/05, 5:11 PM

Chapter 8: Using the TV’s features Adjusting the audio (continued) Adjusting the audio quality 5. To save the new settings, highlight Done and press ENTER. To reset the settings to the factory defaults, You can adjust the audio quality by adjusting the bass, treble, highlight Reset and pres ENTER. and balance. To turn off the SBS: To adjust the audio quality: Highlight Off in step 3. 1. Press MENU and open the Audio menu. 2. Highlight Audio Settings and press ENTER. Using the StableSound® feature Audio The StableSound® feature limits the highest volume level to Audio Settings Advanced Audio Settings prevent extreme changes in volume when the signal source Audio Setup changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial). Navigate Select CH RTN Back EXIT Exit To turn on the StableSound® feature: 1. Press MENU and open the Audio menu. 3. Press z to highlight the item you want to adjust (Bass, 2. Highlight Audio Settings and press ENTER. Treble, or Balance). Audio Settings Bass 100 Audio Treble 100 Audio Settings Balance 0 Advanced Audio Settings SBS On Audio Setup SBS Level 85 StableSound Off Reset Done 4. Press x or • to adjust the level. Navigate Select CH RTN Back EXIT Exit • x makes the bass or treble weaker or increases the balance 3. Press z to highlight StableSound, and then press x or • to in the left channel (depending on the item selected). select On. Audio Settings • • makes the bass or treble stronger or increases the balance Bass 100 in the right channel (depending on the item selected). Treble Balance 100 0 5. To save the new settings, highlight Done and press SBS SBS Level 85 On ENTER. To reset the settings to the factory defaults, StableSound Off highlight Reset and press ENTER. Reset Done 4. To save the new settings, highlight Done and press Using the sub-bass system (SBS) ENTER. To reset the settings to the factory defaults, The sub-bass system allows you to enhance bass performance, highlight Reset and press ENTER. even when the volume is low. Note: The RESET function returns your audio adjustments to To turn on the SBS and adjust the level: the following factory settings: 1. Press MENU and open the Audio menu. Bass ............. center (50) 2. Highlight Audio settings and press ENTER. Treble .......... center (50) Balance ........ center (0) 3. Press z to highlight SBS, and then press x or • to select StableSound ... Off On. 4. Press y or z to highlight SBS Level, and then press x or • To turn off the StableSound® feature: to adjust the sub-bass system. Select Off in step 3 above. Audio Settings Bass 100 Treble 100 Balance 0 SBS On SBS Level 85 StableSound Off Reset Done Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 85 HM95_R2_079-86_061505 85 6/27/05, 5:12 PM

Chapter 8: Using the TV’s features Adjusting the audio (continued) Using the SRS WOW™ surround sound To turn off the built-in speakers: 1. Press MENU and open the Audio menu. feature 2. Highlight Audio Setup and press ENTER. WOW™ is a special combination of SRS Labs audio technologies (SRS 3D, FOCUS, and TruBass) that creates a thrilling surround sound experience with deep, rich bass from Audio stereo sound sources. Your TV’s audio will sound fuller, richer, Audio Settings and wider. Advanced Audio Settings Audio Setup ™ To adjust the WOW settings: 1. Put the TV in STEREO mode (see “Selecting stereo/SAP 3. Press z to highlight the Speakers field, and then press x or broadcasts” on page 84). • to select Off. 2. Press MENU and open the Audio menu. Audio Setup 3. Highlight Advanced Audio Settings and press ENTER. MTS Stereo Language English Speakers On Optical Output Format Dolby Digital Reset Done Audio Audio Settings Advanced Audio Settings Audio Setup 4. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER. 4. Press z or y to highlight the WOW feature you want to adjust, and then press x or • to adjust the item. To turn on the built-in speakers: Advanced Audio Settings Select On in step 3 above. WOW: SRS 3D Off WOW: FOCUS WOW: TruBass Off Low Selecting the optical audio output Reset Done format • WOW: SRS 3D — To turn the surround sound effect On Use this feature to select the optical audio output format when or Off. you connect a Dolby Digital decoder or other digital audio Note: If the broadcast is monaural, the 3D effect does not system to the Optical Audio Out terminal on the TV (see work. “Connecting a digital audio system” on page 20). • WOW: Focus — To turn the vocal emphasis effect On or To select the optical audio output format: Off. 1. Press MENU and open the Audio menu. • WOW: TruBass — To select the desired bass expansion 2. Highlight Audio Setup and press ENTER. level (High, Low, or Off ). 5. To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset Audio Audio Settings and press ENTER. Advanced Audio Settings Audio Setup Turning off the built-in speakers 3. Press z to highlight the Optical Output Format field, and Use this feature to turn off the TV speakers when you connect then press x or • to select either Dolby Digital or PCM, an audio system to your TV (see “Connecting a digital audio depending on your device. system” and “Connecting an analog audio system” on page 20). Audio Setup MTS Stereo Language English Speakers On Optical Output Format Dolby Digital Reset Done 4. To save the new settings, highlight Done and press ______________ ENTER. To revert to the factory defaults, highlight Reset • WOW, SRS and symbol are trademarks of SRS Labs, Inc. WOW technology is and press ENTER. incorporated under license from SRS Labs, Inc. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 86 HM95_R2_079-86_061505 86 6/27/05, 5:12 PM

Chapter 8: Using the TV’s features Using the memory card JPEG picture viewer/MP3 audio player You can use the memory card slots on the TV side panel to view ■ Maximum memory card capacity: 512 MB. compatible JPEG files or play compatible MP3 files stored on a ■ Maximum displayable JPEG image size: 8 MB. memory card (see “Memory card specifications” below and at right). You can display JPEG files in thumbnail mode or view • JPEG files larger than 8 MB will not display. them as a slide show. ■ Maximum MP3 file size: Note: • MP3 files have no size limit other than the maximum capacity • Never remove the memory card or turn off the TV while of the memory card. using the memory card. Doing so may result in loss of data and/or damage to the memory card and/or TV. SUCH DAMAGE ■ Maximum displayable JPEG image resolution: 6000x4000 IS NOT COVERED BY YOUR TOSHIBA WARRANTY. pixels. • It is recommended that you back up your memory card data. Toshiba ■ Maximum number of files per directory: 370. is not liable for any damage caused by the use of any memory card with this TV. Toshiba will not compensate for any lost data or • All files over the 370th in a single directory will not display/play. recording(s) caused by the use of such cards. • Files in directories more than 10 levels down from the top level • For instructions on using your digital camera, refer to the owner’s directory will not display/play. manual for your camera. ■ Maximum number of files per memory card: JPEG = 1,000; • For instructions on using your memory card, refer to the owner’s MP3 = 200. manual for your memory card. • Failure to take proper care of a memory card may prevent display of • All JPEG files over the 1,000th on a single memory card will not pictures or playback of MP3 files from the card or result in damage to display. the memory card and/or TV. SUCH DAMAGE IS NOT COVERED BY • All MP3 files over the 200th on a single memory card will not play. YOUR TOSHIBA WARRANTY. See “Memory card care and ■ File name restrictions: handling” on page 90. • The technical criteria set out in this owner’s manual are meant as a • File names cannot contain the following characters: \ / : ? “ < > | . guide only. • File names must contain US-ASCII characters only. • Permission is required in order to download MP3 files and music from • The maximum file name length is 255 characters. the Internet. Toshiba has no right to grant such permission. Permission • The memory card reader recognizes only “.mp3” and “.jpg” should always be sought from the copyright owner. file extensions. • The MP3 player supports only ISO-8859-1 (US-ASCII/Western European) character sets for MP3 meta-data (e.g, artist name, Memory card specifications album name, song title, etc.) ■ Supported memory card types: ■ JPEG picture viewer: – Memory Card (ver. 1.0) • The picture viewer supports JPEG format images only. – MMC (MultiMediaCard™) • The files on your memory card must be in a file and directory format compatible with the TV or they will not display on the TV. – MemoryStick™ (Pro) • Images processed and/or edited on a personal computer (PC) – xD-Picture Card™ (16MB-512MB) may not display properly or at all. Some digital cameras may store – CompactFlash® memory card (Type1) images in a format that is not compatible with the TV. Note: The picture viewer and audio player support FAT16 formatted ■ MP3 audio player: cards only. Other memory card formats (including, but not limited to, FAT32 and NTFS) are not supported. • The audio player supports MP3 format files only. • The files on your memory card must be in a file and directory format compatible with the TV or they will not play. ______________ • Files processed and/or edited on a personal computer (PC) may • is a trademark of SD Card Association. not play properly or at all. Some MP3 files may be in a format that • MMC and MultiMediaCard are trademarks of Infineon Technologies AG is not compatible with the TV. and licensed to MMCA (MultiMediaCard Association). • MP3 files must have the following format: • Memory Stick is a trademark of Sony Corporation. • xD-Picture Card is a trademark of Fuji Photo Film Co., Ltd. - MPEG1 (ISO/IEC 11172-3) Layer3. • Toshiba is an authorized licensee of the CompactFlash® and CF logo® - Sampling frequency—MPEG1: 32 kHz, 44.1 kHz, 48 kHz. registered trademarks. - Bitrate—MPEG1: 32–320 kbps. - Channels—Stereo, Joint stereo, Dual channel, Single channel. - ID3 Ver. 1, Ver. 2. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 87 HM95_R2_087-92_061505 87 6/27/05, 6:07 PM

Chapter 8: Using the TV’s features Using the memory card JPEG picture viewer/MP3 audio player (continued) Using the JPEG picture viewer 2. In a few seconds, the images automatically display on- screen, with one as a large picture and six in thumbnail Note: If you stored both JPEG and MP3 files on the same format. memory card, the JPEG picture viewer will start automatically Picture Viewer when you insert the memory card in the TV. To start the audio 1 of 6 May 28 04 player, you must first press EXIT to close the picture viewer and 2 of 6 Jan 8 04 then start the audio player while the memory card is still 3 of 6 Jan 18 04 inserted. See “To start the MP3 audio player when a memory 4 of 6 May 12 04 card is already inserted,” on page 90. You cannot use the 5 of 6 Sep 18 04 6 of 6 picture viewer and audio player at the same time. Sep 18 04 Rotate Next Slide Show EXIT Exit To view digital photos on your TV: 1. Insert a memory card into the appropriate memory card 3. Press x to rotate the large picture 90° counterclockwise. Picture Viewer slot on the side of your TV. 1 of 6 May 28 04 Note: 2 of 6 Jan 8 04 3 of 6 • Never insert more than one memory card at one time. Jan 18 04 4 of 6 May 12 04 • Be sure to insert the card correctly—label side facing left and 5 of 6 Sep 18 04 the end with the notched corner (if applicable) inserted into the 6 of 6 Sep 18 04 memory card slot. Rotate Next Slide Show EXIT Exit • When a Compact Flash memory card is inserted correctly, the ejector button pops out (see illustration below). 4. Press • to rotate the large picture 90° clockwise. Picture Viewer 1 of 6 May 28 04 Memory card slots 2 of 6 Jan 8 04 3 of 6 { Jan 18 04 4 of 6 May 12 04 5 of 6 Sep 18 04 6 of 6 TV side Rotate Next Slide Show Sep 18 04 EXIT Exit panel 5. Press y or z to select another picture as the large picture. 6. Press ENTER to view your pictures in a slide show. Picture Viewer ➔ ➔ CompactFlash ejector button ➔ ➔ During the slide show: or • To stop on an image during the slide show, press ENTER. To resume the slide show, press ENTER again. or • To rotate the picture, press x or •, and then press ENTER. CompactFlash xD-Picture Card MMC memory card • To select another image, press y or z, and then press (MultiMediaCard) ENTER. • To stop the slide show and return to the picture viewer, press CH RTN. ™ Secure Digital or • To stop the slide show and return to the regular TV screen, press EXIT. SD Memory Stick (Secure Digital) memory card Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 88 HM95_R2_087-92_061505 88 6/27/05, 6:07 PM

Chapter 8: Using the TV’s features Using the memory card JPEG picture viewer/MP3 audio player (continued) To set the slide show interval: Using the MP3 audio player Note: The picture viewer must be closed before you can set the slide show interval. Note: • If you stored both JPEG and MP3 files on the same memory card, 1. Press MENU and open the Setup menu. the JPEG picture viewer will start automatically when you insert the 2. Highlight Slide Show Interval and press ENTER. Select the memory card in the TV. To start the audio player, you must first press interval from the menu sidebar (2, 5, 10, 15, or 20 EXIT to close the picture viewer and then start the audio player while seconds). the memory card is still inserted. See “To start the MP3 audio player when a memory card is already inserted,” next page. You cannot use the picture viewer and audio player at the same time. Setup • Make all desired adjustments to the surround, bass, treble, and Installation 2 sec Sleep Timer 5 sec balance before starting the MP3 audio player. On/Off Timer 10 sec HDMI 1 Audio Auto 15 sec • Permission is required in order to download MP3 files and music from HDMI 2 Audio Auto 20 sec the Internet. Toshiba has no right to grant such permission. Permission Slide Show Interval 2 Sec AVHD Skip Time 15 min should always be sought from the copyright owner. Navigate Select CH RTN Back EXIT Exit To start the MP3 audio player when a memory card is not already inserted: To close the picture viewer: 1. Insert a memory card into the appropriate memory card Press EXIT to close the picture viewer and return to the regular slot on the side of your TV (see page 88 for details). TV screen. Note: To restart the picture viewer while the memory card is still • Never insert more than one memory card at a time. inserted: • Be sure to insert the card correctly—label side facing left and 1. Press MENU and open the Applications menu. the end with the notched corner (if applicable) inserted into the memory card slot. 2. Highlight Picture Viewer and press ENTER. • When a CompactFlash memory card is inserted correctly, the ejector button pops out (see page 88). Applications 2. If you have only MP3 files on the memory card, the audio TV Guide On Screen Audio Player player will launch within a few seconds after being inserted Picture Viewer and begin playing the first MP3 file on the memory card. Digital CC/Audio Selector CableCARD Audio Player Title Artist Ser No.1 in D, Op.11... SCO/Sir Charles... Vol Navigate Select CH RTN Back EXIT Exit Requiem, Op. 5: IV. R... Robert Shaw/Atla... Rapsodie Espagnole:... Jesus Lopez-Cobo... Moolight Sonata, movement III. Sanctus: Sanctu... Boston Baroque/M... 3. Follow the steps under “To view digital photos on your Piano Sonata, K. 545... A-M Classical A-M Classical Pathétique Sonata, m... A-M Classical TV” on the previous page. Chopin Prelude No. ... Andrys Piano Sonata, K. 545... A-M Classical Moolight Sonata, mo... A-M Classical To close the picture viewer and remove the memory card: 1. Press EXIT to close the picture viewer and return to the Navigate Select EXIT Exit regular TV screen. 3. Press yz x • to navigate to the rewind, pause, fast NOTE: ALWAYS CLOSE THE PICTURE forward, skip backward, skip forward, volume, and mute VIEWER BEFORE REMOVING THE buttons, or to select another MP3, and then press ENTER. MEMORY CARD. If you remove the memory card while viewing pictures, the card To use the mute function and/or saved data may be damaged. THIS TYPE OF DAMAGE IS NOT COVERED UNDER YOUR TOSHIBA WARRANTY. Press yz x • to select the (mute) button, and then press ENTER. See page 84 for details on muting the sound. 2. For a CompactFlash memory card, press the ejector button and then pull the card straight out from the TV. For all other memory cards, pull the card straight out from the TV. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 89 HM95_R2_087-92_061505 89 6/27/05, 6:07 PM

Chapter 8: Using the TV’s features Using the memory card JPEG picture viewer/MP3 audio player (continued) Using the MP3 audio player (continued) Memory card care and handling To start the MP3 audio player when a memory card is • Use index labels made exclusively for your specific brand of already inserted: memory card. Do not use commercially sold labels, which can cause a malfunction when the card is inserted or 1. Press MENU and open ejected. the Applications menu. Applications 2. Highlight Audio Player TV Guide On Screen • If the image does not appear correctly or the audio file does and press ENTER. Audio Player not play correctly, clean the metallic area of the memory Picture Viewer Digital CC/Audio Selector card using a soft, dry, lint-free, anti-static cloth and then 3. Press yz x • to CableCARD reinsert the card. navigate to the rewind, pause, fast forward, skip • Prevent the metallic area on the memory card from coming Navigate Select CH RTN Back EXIT Exit backward, skip forward, in contact with dust, dirt, or other foreign particles. Do not volume, and mute buttons, and then press ENTER. touch the metallic area of the memory card with your hands or otherwise handle it with anything other than a soft, dry, Note: After 30 seconds a screen saver will appear. To access the lint-free, anti-static cloth. screen saver immediately, press any button on the remote control. Note: Toshiba is not liable for any damage caused by the use To close the MP3 audio player: of any memory card with this TV. Toshiba will not compensate for any lost data or recordings caused by the use of such Press EXIT to close the audio player and return to the regular cards. TV screen. To close the MP3 audio player and remove the memory card: NOTE: ALWAYS CLOSE THE AUDIO 1. Press EXIT to close the audio player and return to the PLAYER BEFORE REMOVING THE regular TV screen. MEMORY CARD. 2. For a CompactFlash memory card, press the ejector button If you remove the memory card while playing MP3 files, the card and then pull the card straight out from the TV. For all and/or saved data may be damaged. THIS TYPE OF DAMAGE other memory cards, pull the card straight out from the TV. IS NOT COVERED UNDER YOUR TOSHIBA WARRANTY. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 90 HM95_R2_087-92_061505 90 6/27/05, 6:07 PM

Chapter 8: Using the TV’s features Setting the On/Off Timer Setting the sleep timer You can use the On/Off Timer to turn the TV on and off at a You can set the sleep timer to turn off the TV after a set length preset time on a recurring basis. of time (maximum of 3 hours). The sleep timer turns off the TV Note: You must first set the time (see page 50). one time only, as opposed to the On/Off Timer, which turns off the TV on a recurring basis. To set the On/Off Timer: To set the sleep timer: 1. Press MENU and open the Setup menu. Press SLEEP on the remote control to set the length of time until 2. Highlight On/Off Timer and press ENTER. the TV turns off. Repeatedly press SLEEP to increase the time in 10-minute increments or press y or z to increase or decrease the Setup time in 10-minute increments, to a maximum of 3 hours and 00 Installation minutes. Sleep Timer On/Off Timer To cancel the sleep timer: HDMI 1 Audio Auto HDMI 2 Audio Slide Show Interval Auto 2 Sec Press SLEEP until it is set to 0. AVHD Skip Time 15 min Navigate Select CH RTN Back EXIT Exit SLEEP 3. Press z to highlight the DAY field, and then press x or • to select the recurrence (weekends, weekdays, every day, etc). To set the sleep timer using the on-screen menus: On/Off Timer 1. Press MENU and open the Setup menu. Turn TV ON: 2. Press z to highlight Sleep Timer and press ENTER. Day Weekends Time (HH:MM) 0 9 : 0 0 AM TV ON Duration: 30 Minutes Reset Cancel Done Setup Installation Sleep Timer 4. Press z to highlight the Time field, and then use the On/Off Timer HDMI 1 Audio Auto Number buttons to enter the time you want the TV to turn HDMI 2 Audio Auto on. Slide Show Interval 2 Sec AVHD Skip Time 15 min 5. When the AM/PM field is highlighted, press x or • to Navigate Select CH RTN Back EXIT Exit select AM or PM. 6. Press z to highlight the TV ON Duration field, and then 3. Press the Number buttons to enter the length of time in press x or • to select the length of time until the TV turns 10-minute increments. off. Sleep Timer 7. Highlight Done and press ENTER. Enter total minutes until the TV turns off automatically (Maximum 180 minutes) 8. Turn off the TV. The TV will turn on automatically on the day(s) and at the time you set. The TV will then turn off 1 2 0 automatically after the length of time you set in the TV Cancel Done ON Duration field. Note: 4. Highlight Done and press ENTER. • When a power failure occurs, the On/Off Timer settings may Note: be cleared. • When a power failure occurs, the sleep timer setting may be cleared. • To display the On Timer setting, press RECALL. • To display the amount of time left on the sleep timer, press RECALL. To turn off the On/Off Timer: To display the remaining time on the sleep timer: Select Not Set in step 3 above. Press SLEEP. On/Off Timer Sleep Timer Turn TV ON: Day Not Set 1h10m Note: Reset Cancel Done A message will display on-screen when there is one minute remaining on the sleep timer. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 91 HM95_R2_087-92_061505 91 6/27/05, 6:08 PM

Chapter 8: Using the TV’s features Displaying the Channel Banner Understanding the auto power off To display the channel banner: feature Press RECALL on the remote control. The TV will automatically turn itself off after approximately 15 The following information will display in the channel banner minutes if it is tuned to a vacant channel or a station that (if applicable): completes its broadcast for the day. This feature functions in • Current input (ANT 1, ANT 2, VIDEO 1, etc.) ANT 1 and ANT 2 modes only. • If ANT 1 or ANT 2 is the current input, whether it is Cable TV (“CABLE”) or STEREO Tuner Hold: On off-air (“TV”) • Channel number (if in NC-17 On Timer: Weekdays 12:00pm Understanding the last mode ANT 1 or ANT 2 mode) Sleep Timer: 18 min. Game Timer: 28 min. ANT 1 memory feature • Signal strength indicator Natural (bar graph in lower right 1080i CABLE 81-1 5:32pm If the power is cut off while you are viewing the TV, the Last corner of banner; for Sample channel banner screen Mode Memory feature automatically turns on the TV when ATSC signal only) the power is resupplied. Note: The signal strength indicator will react to fading and increasing signals and could display longer than the normal NOTE: You should unplug the TV’s power cord if it is possible channel banner screen. that you will be away from the TV for an extended period of time after the power is restored. • Time (if set) • On/Off timer settings (if set) • Remaining time on sleep timer (if set) • Remaining time on game timer (if set) Using the gray level feature • Stereo or SAP audio status • V-Chip rating status The gray level feature will set the sidebars to three different • Picture size levels of darkness. Sidebars are the blanks spaces on either side of a 4:3 viewing area. • Tuner hold* (if applicable) To set the gray level of the sidebars: *If you are recording on one tuner (for example, the digital tuner), you will be able to change channels on the other tuner 1. Press MENU and open the Setup menu. only (the analog tuner in this example). The tuner from which 2. Highlight Gray Level and press •. you are recording is “on hold” (i.e., locked) so your recordings will not be affected by channel changes. 3. Press y or z to select your desired level of darkness (1 – Black, 2 – Dark Gray or 3 – Gray). • Aspect ratio • Lamp mode (appears only if the TV is in Hi Bright mode) To close the channel banner: Setup Sleep Timer 1 Press RECALL again. On/Off Timer 2 HDMI 1 Audio Auto 3 HDMI 2 Audio Auto Slide Show Interval 2 Sec AVHD Skip Time 15 min Gray Level 2 Navigate Select CH RTN Back EXIT Exit Note: • The gray level feature does not affect video being viewed in 16:9 aspect ratio. • When receiving a signal that has sidebars (e.g., 4:3 aspect ratio video over a 1080i or 720p signal), the gray level feature will not be applied to the sidebars. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 92 HM95_R2_087-92_061505 92 6/27/05, 6:08 PM

9 Using the Locks menu The Locks menu includes the Enable Rating Blocking, Edit Rating Limits, Channels Block, Input Lock, Front Panel Lock, Game Timer, and New PIN Code features. You can use these features after entering the correct PIN code. Entering the PIN code If you cannot remember your PIN code 1. Press MENU and highlight the Locks menu icon. While the PIN code entering screen is displayed, press RECALL four times within five seconds. The PIN code will be cleared and Locks Enable Rating Blocking Off you can enter a new PIN code. Edit Rating Limits Channels Block Input Lock Off Front Panel Lock Off Game Timer Off New PIN Code Navigate Select CH RTN Back EXIT Exit Changing your PIN code 2. Press z, which displays the PIN code entry screen. 1. Press MENU and highlight the Locks menu icon. • The Lock System screen (below) appears if a PIN code has 2. Press z to display the PIN code entering screen. not been stored. Press the Channel Number buttons to 3. Enter your four-digit PIN code and press ENTER. enter a new four-digit code, enter the code a second time to 4. Press z to highlight New PIN Code and press ENTER. confirm, and press ENTER. Lock System Locks Enable Rating Blocking Off Please enter a 4 digit PIN code Edit Rating Limits Channels Block Input Lock Off Confirm PIN code Front Panel Lock Off Game Timer Off New PIN Code Cancel Done Navigate Select CH RTN Back EXIT Exit 5. Press the Number buttons to enter a new four-digit code. • The Locks/Active screen (below) appears if the PIN code is Retype the numbers to confirm the PIN code you entered. already stored. Press the Channel Number buttons to enter 6. Press ENTER. The new PIN code is now active. your four-digit code and press ENTER. New PIN Code Locks Active Please enter a 4 digit PIN code Please enter the 4 digit PIN code * * * * * * * * Confirm PIN code * * * * Cancel Done Cancel Done If the wrong PIN code is entered, the message “Incorrect PIN code, please try again!” appears. Highlight Retry and press ENTER. Enter the code again and press ENTER. When the correct PIN code is entered, the Locks menu opens. Locks Enable Rating Blocking Off Edit Rating Limits Channels Block Input Lock Off Front Panel Lock Off Game Timer Off New PIN Code Navigate Select CH RTN Back EXIT Exit Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 93 HM95_R2_093-96_061505 93 6/27/05, 6:23 PM

Chapter 9: Using the Locks menu Blocking TV programs and movies by rating (V-Chip) Some TV programs and movies include signals that classify the Independent rating system for broadcasters content of the program (violence, sex, dialog, language). The V-Chip feature in this TV detects the signals and blocks the Ratings Description and Content themes programs according to the ratings you select. (See the tables at TV-MA Mature Audience Only (This program is specifically designed right for rating descriptions.) to be viewed by adults and therefore may be unsuitable for children under 17.) Note: Rating blocking is a function of the V-Chip feature in this L) Crude or indecent language S) Explicit sexual activity TV, which supports the U.S. V-Chip system only. V) Graphic violence To block and unblock TV programs and movies: TV-14 Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children 1. Press MENU and highlight the Locks menu icon. under 14 years of age.) 2. Press z, which displays the PIN code entering screen. D) Intensely suggestive dialog L) Strong, coarse language S) Intense sexual situations V) Intense violence 3. Enter your four-digit PIN code and press ENTER. TV-PG Parental Guidance Suggested (This program contains 4. Press z to highlight Enable Rating Blocking. material parents may find unsuitable for younger children.) 5. Press • and then z to select On, and then press ENTER. D) Some suggestive dialog L) Infrequent coarse language S) Some sexual situations V) Moderate violence TV-G General Audience (Most parents would find this program Locks suitable for all ages.) Enable Rating Blocking Off Off Edit Rating Limits On TV-Y7, Directed to Older Children (This program is designed Channels Block Input Lock Off TV-Y7FV for children age 7 and above. Note: Programs in which Front Panel Lock Off fantasy violence may be more intense or more combative Game Timer Off than other programs in this category are designated Y7FV.) New PIN Code TV-Y All Children (This program is designed to be appropriate for Navigate Select CH RTN Back EXIT Exit all children.) 6. Press z to highlight Edit Rating Limits and press ENTER. Independent rating system for movies Locks Enable Rating Blocking Off Rating Description and content themes Edit Rating Limits Channels Block X X-rated (For adults only) Input Lock Off Front Panel Lock Off NC-17 Not intended for anyone 17 and under Game Timer Off New PIN Code R Restricted (Under 17 requires accompanying parent or adult) Navigate Select CH RTN Back EXIT Exit PG-13 Parents Strongly Cautioned (Some material may be inappropriate for children under 13) The Edit Rating Limits screen (below) appears. PG Parental Guidance Suggested (Some material may not be 7. Press yzx • and then press ENTER to select the level of suitable for children) blocking you prefer. A box with an “X” is a rating that will G General Audience (Appropriate for all ages) be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen. See notes at right. Note: 8. When done selecting the ratings you want to block, • If you place an “X” in the box next to “None” Rated or “No Rating,” highlight Done and press ENTER. programs rated “None” or “No Rating” will be blocked. However, if the program does not provide any rating information, nothing will be Edit Rating Limits TV (V-CHIP) FV D L S V Movies displayed in the banner and ratings blocking will not take effect. TV-Y G Children • To display the rating of the program you are watching, press TV-Y7 PG Youth TV-G PG-13 RECALL on the remote control. If it is not rated, the word “NONE” TV-PG R appears. TV-14 NC-17 TV-MA X Cancel "None" Rated or "No Rating" TV – PG L V NONE Done This program is designed for children age 7 and adove. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 94 HM95_R2_093-96_061505 94 6/27/05, 6:23 PM

Chapter 9: Using the Locks menu Blocking channels Unlocking programs temporarily With the Channels Block feature, you can block specific If you try to watch a TV program that exceeds the rating limits channels. You will not be able to tune blocked channels unless you set, the TV enters program lock mode. You can either you clear the setting first. unlock the program temporarily or select a non-locked program to watch. To block channels: 1. Press MENU and highlight the Locks menu icon. 2. Press z, which displays the PIN code entering Locks screen. Enable Rating Blocking Off To temporarily unlock the program: 3. Enter your four-digit Edit Rating Limits Channels Block 1. Press MUTE. PIN code (see page 93 Input Lock Front Panel Lock Off Off 2. Enter your four-digit PIN code and press ENTER. If the for details). Game Timer Off correct code is entered, Locks Active New PIN Code 4. Press z to highlight the program lock mode Enter PIN code to temporaily un- Channels Block and Navigate Select CH RTN Back EXIT Exit is released and the block. then press ENTER. normal picture appears. * * * * 5. Using the yz x • buttons, select the input for which you All locking is disabled want to change the rating limits (ANT1, ANT2, or Cable until the TV is turned Cancel Done Box, if connected) and press ENTER. off, and will be enabled when the TV is turned on again. A list of the channels available for that input will be displayed along with the call letters for each channel, if available. Locking video inputs 6. Press yz x • to Channels Block ANT 1 highlight the channel 1 ANT 1 You can use the Input Lock feature to lock the video input you want to block, then 2 ANT 2 sources (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD-1, press ENTER, which 3 4 Cable Box ColorStream HD-2, HDMI 1/HDMI 2) and channels 3 and 4. puts an “X” in the box 5 You will not be able to view the input sources or channels until next to that channel. 6 you turn off the input lock. 7 Allow All 7. Repeat step 6 for other 8 Block All To lock the video inputs: 9 Cancel channels you want to 10 Done 1. Press MENU and highlight the Locks menu icon. block. 2. Press z to display the PIN code entering screen. 8. Highlight Done and press ENTER. 3. Enter your four-digit PIN code and press •. To unblock individual channels: 4. Press z to highlight Input Lock and press •. In step 6 above, press yzx • to highlight the channel you 5. Press y or z to select the level of video input locking you want to unblock, and then press ENTER to remove the X from prefer, as described below: the box. VIDEO: Locks VIDEO To block all channels at Channels Block ANT 1 1, VIDEO 2, VIDEO 3, Locks once: 1 ANT 1 ColorStream HD1/ Enable Rating Blocking Off Off 2 ANT 2 HD2, and HDMI. Edit Rating Limits Video Highlight Block All 3 Cable Box Channels Block Video + Input Lock Off in step 6 above. 4 VIDEO+: Locks Front Panel Lock Off 5 VIDEO 1, VIDEO 2, Game Timer Off 6 To unblock all locked 7 Allow All VIDEO 3, ColorStream New PIN Code channels at once: 8 Block All HD1/HD2, HDMI 1/ Navigate Select CH RTN Back EXIT Exit Highlight Allow All 9 10 Cancel HDMI 2, and channels Done in step 6 above. 3 and 4. Select VIDEO+ if you use the antenna terminal to Note: Channel blocking may not take effect if you have a cable box play a video tape. connected and use the cable box controls to change channels. Note: Make sure the POP is not on channel 3 or 4. Off: Unlocks all video input sources. 6. Press ENTER. Note: When the CableCARD™ is inserted, Video+ will behave the same as Video lock. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 95 HM95_R2_093-96_061505 95 6/27/05, 6:23 PM

Chapter 9: Using the Locks menu Using the GameTimer™ Using the front panel lock feature You can use the GameTimer to set a time limit for playing a You can lock the front panel touchpad to prevent your settings video game (30–120 minutes). When the GameTimer is from being changed accidentally (by children, for example). activated, the TV enters VIDEO LOCK mode and locks out When the front panel lock is On, none of the controls on the the input source for the video game device. TV front touchpad will operate except POWER. To set the GameTimer™: To lock the front panel: 1. Press MENU and highlight the Locks menu icon. 1. Press MENU and highlight the Locks menu icon. 2. Press z to display the PIN code entering screen. 2. Press z to display the PIN code entering screen. 3. Enter your four-digit PIN code and press •. 3. Enter your four-digit PIN code and press ENTER. 4. Press z to highlight Game Timer and then press •. 4. Press z to highlight Front Panel Lock. 5. Press y or z to select the length of time until the Video 5. Press • to highlight On and press ENTER. When the front Lock is activated (30, 60, 90, or 120 minutes) and press panel is locked and a button on the touchpad is pressed, the ENTER. message “Not Available” appears. Locks Locks Enable Rating Blocking Off Off Enable Rating Blocking Off Off Edit Rating Limits 30 Min Edit Rating Limits On Channels Block 60 Min Channels Block Input Lock Off 90 Min Input Lock Off Front Panel Lock Off 120 Min Front Panel Lock Off Game Timer Off Game Timer Off New PIN Code New PIN Code Navigate Select CH RTN Back EXIT Exit Navigate Select CH RTN Back EXIT Exit To cancel the GameTimer™: To unlock the front panel: Select Off in step 5 above. Highlight Off in step 5 above, or press and hold the To deactivate the video lock once the GameTimer has VOLUME x button on the TV front panel for about 10 activated it: seconds until the volume icon appears on-screen. Set the VIDEO LOCK to OFF (see “Locking video inputs” on TV front touchpad page 95). Note: • A message will appear on-screen when 10 minutes, 3 minutes, and 1 minute remain on the GameTimer. • If the TV loses power with time remaining on the GameTimer, when power is restored the TV will enter VIDEO LOCK mode (as if the GameTimer had expired) and you will have to VOLUME x deactivate the video lock (as described above). Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 96 HM95_R2_093-96_061505 96 6/27/05, 6:23 PM

10 Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom Solution TV will not turn on • Make sure the power cord is plugged in, and then press POWER. • The remote control batteries may be dead. Replace the batteries or try the front panel buttons. • If you have recently replaced the lamp unit, make sure the lamp unit and lamp unit door are installed properly (pages 103–105). • The lamp unit may need to be replaced (pages 103–105). Also see “LED indications” on page 99. No picture after TV is turned on • When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen. See "IMPORTANT NOTICE ABOUT HOT LAMP RESTART" on page 8. Picture problems • Check the antenna/cable connections (Chapter 2). • Press INPUT on the remote control or TV/VIDEO on the TV front panel and select a valid video input source (page 67). If no device is connected to any of the inputs on the TV, no picture will display when you select that particular input source. For device connection details, see Chapter 2. • Antenna reception may be poor. Use a highly directional outdoor antenna (if applicable). • The station may have broadcast difficulties. Try another channel. • Adjust the picture qualities (page 79). • If you are using a VCR, make sure the TV/VCR button on the remote control is set correctly (page 26). • If you have two VCRs connected to your TV, do not connect the same VCR to the TV’s output and input connections at the same time (page 18). • Do not connect a standard video cable and an S-video cable to VIDEO-1 or VIDEO-2 on the TV back (or VIDEO-3 on the TV side) at the same time (Chapter 2). Noisy picture • If you are watching a tuned analog channel (off-air broadcast or Cable TV), set the CableClear®/DNR feature to AUTO to reduce visible interference in the TV picture (page 80). Video Input Selection • If the Input Selection window does not appear when you press INPUT on the remote control or problems TV/VIDEO on the TV front panel, press INPUT or TV/VIDEO a second time, which will change to the next video input source and display the Input Selection window. Cannot view external signals • If you cannot view signals from external devices connected to VIDEO 1, VIDEO 2, or channel 3 or 4 VIDEO 3, or ColorStream,® or from channels 3 or 4, make sure the Input Lock is set to Off (page 95). Black box on screen • Set the Closed Caption feature to Off (page 82). Poor color or no color • The station may have broadcast difficulties. Try another channel. • Adjust the Tint and/or Color (page 79). • When the ColorStream® signal source is active, the VIDEO OUT terminal outputs blank video. To receive video from the VIDEO OUT signal, a standard video or S-video IN terminal must be used instead of the ColorStream® connections. POP problems • The VIDEO OUT terminal will not output the POP picture (pages 18 and 76). • If you label all of the inputs as “Hide,” the POP feature will be disabled. If you then attempt to access the POP feature, the message “Not available” will appear on-screen (page 68). Picture brightness changes • If you set the lamp mode to Low Power, each time you turn on the TV, the lamp will start out in High Bright soon after turning on TV mode but will switch to Low Power mode in approximately 1 minute. You will notice a change in screen brightness when this happens. This is normal and is not a sign of malfunction. (See page 75.) Picture and sound are out of sync • As with all products that contain a digital display, in rare instances, when viewing certain content (e.g., television broadcasts, video games, DVDs), you may notice that the picture and sound are slightly out of sync. This phenomenon can be caused by various factors including, without limitation, video processing within the TV, video processing in an attached gaming system, and video processing/different compression rates used by broadcasters in their programming. You may want to try one or more of the following suggestions, which may help to reduce the effect of this phenomenon: - If the TV is connected to an A/V receiver that has a programmable audio delay feature, use this feature to help synchronize the sound to the picture. - If you notice this phenomenon only on certain TV channels, please contact your local broadcast, cable, or satellite provider to inform them of this issue. Memory card • Make sure you are using a supported or valid memory card format (page 87). problems • Make sure you have saved the picture files in the correct file format (page 87). • The card may be inserted improperly. Remove the card and reinsert it (page 88). • The memory card may be empty. • The memory card may be damaged. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 97 HM95_R2_097-102_061505 97 6/27/05, 8:14 PM

Chapter 10: Troubleshooting Symptom Solution Sound problems • Check the antenna/cable connections (see Chapter 2). • The station may have broadcast difficulties. Try another channel. • The sound may be muted. Press VOLUME. • If you hear no sound, try setting the MTS feature to STEREO mode (page 84). • Make sure the Speakers function in the Audio Setup menu is set correctly (page 86). • If you are not receiving a second audio program from a known SAP source, make sure the MTS feature is set to SAP mode (page 84). • If you hear audio that seems “incorrect” for the program you are watching (such as music or a foreign language), the SAP mode may be on. Set the MTS feature to STEREO mode (page 84). • When using an external audio amplifier, if you connect the amplifier to the VAR. AUDIO OUT terminals, the volume of the TV and amplifier must be set above 0 or you will not hear any sound (page 20). Remote control problems • Make sure the remote control is set to the correct device mode (page 28). • Remove all obstructions between the remote control and the TV. • The remote control batteries may be dead. Replace the batteries (page 28). • Your TV remote control may not operate certain features on your external device. Refer to the owner’s manual for your other device to determine its available features. If your TV remote control does not operate a specific feature on another device, use the remote control that came with the device (page 28). • If the TV stops responding to the controls on the remote control or TV front panel and you cannot turn off the TV, press and hold the POWER button on the TV front panel for 5 or more seconds to reset the TV. • If the TV still does not act as expected, use the Restore Factory Defaults procedure as described on page 52. Channel tuning problems • Make sure the remote control is set to the correct device mode (page 28). • The channel may have been erased from the channel memory by the Channel Add/Delete feature. Add the channel to the channel memory (page 43). • The channel may be blocked by the Channels Block feature. Unblock the channel (page 95). • If you are unable to tune digital channels, check the antenna configuration (page 41). If you are still unable to tune digital channels, clear all channels from the channel list (page 43) and reprogram channels into the channel memory (page 42). If you are still unable to tune digital channels, use the Restore Factory Defaults procedure as described on page 52. Also see “Other problems,” below. Closed caption problems • If the program or video you selected is not closed-captioned, no captions will display on-screen (page 82). • If text is not available, a black rectangle may appear on-screen. If this happens, turn off the closed caption feature (page 82). • A closed caption signal may not display correctly in the following situations: a) when a videotape has been dubbed; b) when the signal reception is weak; or c) when the signal reception is nonstandard (page 82). Rating Blocking (V-Chip) problems • If you forget your PIN code: While the PIN code entering screen is displayed, press RECALL four times within 5 seconds. The PIN code you previously stored will be cleared (page 93). • The V-Chip feature is available for the U.S. V-Chip system only (page 94). Recording problems • If you use the TV’s remote control to start recording, you will not be able to change inputs (page 67), open the POP window (page 76), or open the FAV SCAN multi-window (page 78). If you attempt to do so, the message “Not Available While Recording” will appear on-screen. • If you are recording a digital channel, you will only be able to change analog channels while the recording is in progress. If you are recording an analog channel, you will only be able to change digital channels while the recording is in progress. This is because the TV tuner that is being recorded (digital or analog) will be locked on the channel that is currently recording. • It is recommended that you use the TV’s remote control to start recording. If you use a device other than the TV’s remote control to start recording and then attempt to access a feature that is normally denied during recording (POP mode, FAV SCAN mode, changing inputs,) the recorded audio and/or video may not be what you intended to record. See pages 67 and 71. • If you connected a Symbio™ AVHD recorder, in order to use its full functionality, you must first set up the TV Guide On Screen® system (page 23 and Chapter 2). “Now Booting” message • If you unplug the power cord while the TV is on, when you plug the power cord in again, the appears on-screen message “Now Booting…” will display on-screen until the TV enters standby mode. This is normal and is not a sign of malfunction. TV stops responding to controls • If the TV stops responding to the controls on the remote control or TV front panel touchpad and you cannot turn off the TV, press and hold the POWER button on the TV front panel for 5 or more seconds to reset the TV. Other problems • If your TV’s problem has not been addressed in this Troubleshooting section or the recommended solution has not worked, use the Restore Factory Defaults procedure as described on page 52. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 98 HM95_R2_097-102_061505 98 6/27/05, 8:15 PM

Chapter 10: Troubleshooting LED indications The green and red LEDs on the TV front touchpad (to the left of the POWER button) indicate the TV’s status, as described below. • Red ON (solid) and Green OFF = The TV power cord is plugged in. • Green ON (solid) and Red OFF = A recording is in progress while the TV is OFF. • Red ON (solid) and Green ON (solid) = A recording is in progress while the TV is ON. • Green and/or Red blinking (see table below). Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the green LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction. TV/VIDEO EXIT CHANNEL VOLUME MENU POWER TV front touchpad Red LED Green LED LED Indication Condition Solution 1) Green blinks continuously The lamp unit door is not seated Turn OFF the TV and unplug the power cord. Review “How to at 3-second intervals. properly. replace the lamp unit” on pages 104–105 to ensure that the lamp Red blinks continuously door is installed securely. If the problem persists, contact a Toshiba at 0.5-second intervals. Authorized Service Center. 2) Green blinks continuously The lamp is not working properly. The TV will automatically try to restart itself eight times (see item at 0.5-second intervals; #3). Red is ON (solid). 3) Green and Red blink The lamp is not working properly Turn the TV OFF and then ON again. If the problem persists, continuously at after the eighth automatic restart replace the lamp unit (see pages 103–105). If the problem still 1-second intervals. (see item #2). exists, contact a Toshiba Authorized Service Center. 4) Green is OFF; An abnormal temperature Turn OFF the TV. Check to make sure all slots and openings in the Red blinks at 0.2-second increase has occurred. TV cabinet are not covered, blocked, or dusty. Turn ON the TV intervals 4 times (repeat). again. If the problem persists, contact a Toshiba Authorized Service Center. 5) Green is OFF; Abnormal operation Turn OFF the TV and unplug the power cord. Plug the power cord Red blinks continuously (including cooling fan stop). in again and turn ON the TV. If the problem persists, contact a at 0.5-second intervals. Toshiba Authorized Service Center. 6) Green is OFF; Abnormal operation of BUS line. Turn OFF the TV and unplug the power cord. Plug the power cord Red blinks continuously in again and turn ON the TV. If the problem persists, contact a at 1-second intervals. Toshiba Authorized Service Center. 7) Green is OFF; The color wheel has stopped. Turn OFF the TV and unplug the power cord. Plug the power cord Red blinks at 0.2-second in again and turn ON the TV. If the problem persists, contact a intervals 3 times (repeat). Toshiba Authorized Service Center. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 99 HM95_R2_097-102_061505 99 6/27/05, 6:29 PM

Chapter 10: Troubleshooting TV Guide On Screen® FAQs The following are frequently asked questions about the TV Guide On Screen® system. The answers represent the most likely solutions to the problem. After you set up the TV Guide On Screen® system (Chapter 5), the 7. Q: I had a power outage. Do I need to go through initial program guide opens automatically by default when you turn on setup of the TV Guide On Screen® system again? the TV. You can turn off the automatic program guide (see page 40) A: No. The information you entered is stored in the TV Guide and instead press the TV GUIDE button on the remote control to On Screen® system memory. manually open the TV Guide On Screen® program guide. Note: For Cable box users, the TV must be OFF and the Cable box must be left ON for the TV Guide On Screen® system to SETUP receive channel line-up information. 1. Q: What if I move and my ZIP code or postal code changes? 8. Q: How do I connect the G-LINK® (IR blaster) cable to A: Highlight Setup in the Service Bar. Press z to highlight the G-LINK® input on the TV? Change System Settings (page 65), and then press ENTER. A: See Chapter 2: Connecting your TV in this manual. Follow the on-screen prompts to enter new information You also can refer to the TV Guide On Screen® prompts (see Chapter 3 for details). It can take up to 24 hours to during VCR or Cable box setup. receive new data. 9. Q: When will I be able to view my TV program listings and 2. Q: What if I change my cable hook-up to antenna or vice use other TV Guide On Screen® system features? versa? A: You will be able to use initial program listings within 24 A: Highlight Setup in the Service Bar. Press z to highlight hours of initial setup. It may take up to one week to receive Change System Settings (page 65), and then press ENTER. the full eight days of program listings. Follow the on-screen prompts to enter new input information and rescan channels for the new input (see 10. Q: What should I do if I cannot complete initial setup? Chapter 3 for details). A: If you are unable to complete initial setup using the owner’s manual and the on-screen prompts, please call Toshiba’s 3. Q: What if I change cable boxes? National Service Division at 1-800-631-3811. A: Highlight Setup in the Service Bar. Press z to highlight Change System Settings (page 65), and then press ENTER. 11. Q: If I make a mistake during setup, how do I go back to Follow the on-screen prompts to enter new input the previous step? information and rescan channels for the new input (see A: Complete the remaining setup steps. When “Confirming Chapter 3 for details). Your Settings” appears, select “No, repeat setup process.” 4. Q: I used to have a cable box, but now I get direct cable. Follow the on-screen prompts and input the correct What do I do? information. A: Highlight Setup in the Service Bar. Press z to highlight 12. Q: What if the channel number is not visible on my cable Change System Settings (page 65), and then press ENTER. box? Follow the on-screen prompts to enter new input information and rescan channels for the new input (see A: Your cable box may be defaulting to a clock or time display Chapter 3 for details). once the channel changes. Watch the box carefully when testing the cable box brand code to see if the channel 5. Q: If I add a recorder or change my cable service, how do I changes to 09. change my Setup information? A: Highlight Setup in the Service Bar. Press z to highlight 13. Q: Why won’t my VCR turn on? Change System Settings (page 65), and then press ENTER. A: There are several possibilities: Follow the on-screen prompts to enter new information a) An incorrect or “no VCR” code was entered during the (see Chapter 3 for details). It can take up to 24 hours to TV Guide On Screen® initial setup. Press the GUIDE receive new data. button on the remote control, and then press • to highlight SETUP. Press z to highlight “Change system 6. Q: Why does it take up to 24 hours for the TV Guide settings,” and then press ENTER. Follow the on-screen On Screen® system to be ready for use? prompts to select the correct VCR information. A: The initial setup process consists of finding the stations in b) Make sure the G-LINK® (IR blaster) cable is connected your area that carry the TV Guide On Screen® system data correctly (see page 25). and tuning to those stations to receive the setup and c) The VCR record timer is on. Turn off the timer. listings data. d) The wired remote VCR is incompatible. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 100 HM95_R2_097-102_061505 100 6/27/05, 6:29 PM

Chapter 10: Troubleshooting TV Guide On Screen® FAQs (continued) CHANNEL LINE-UPS & LISTINGS 20. Q: After some show titles, I have noticed from 1 to 4 stars 14. Q: Why aren’t all my channels initially displayed? (****). What does that mean? A: After initial setup, approximately 120 channels are A: These stars are a broadcast-industry ratings system used to automatically displayed. The user may use the “Change inform you of a show’s quality. The more stars, the better channel display” feature to turn ON or OFF additional the rating. channels. Note: Even though you have the option of enabling many 21. Q: What do the colors for shows in the Listings and Search more channels, the system may not have the memory capacity screens indicate? to hold detailed program descriptions for all of them. A: Green = Sports; Dark Blue = Children’s; Purple = Movies; Teal = Other Show. 15. Q: When I opened the TV Guide On Screen® system, I was asked to choose from more than one channel lineup. 22. Q: How do I add, delete, or change the assigned number of What should I do? channels on the TV Guide On Screen® system? A: Select the lineup that most closely matches the one for your A: See the “Change channel display” section in the TV Guide area. If after you choose the lineup, you want to make On Screen® owner’s manual (see page 65). changes to it, highlight Setup in the Service Bar. Press z to select Change Channel Display. Follow the on-screen 23. Q: Why are some of my channels listed on the wrong instructions. number? 16. Q: Why do all my channels display “No Listing?” A: There are several possibilities (see page 65 for details): A: The TV Guide On Screen® system has not yet received its a) Incorrect channel lineup was selected. Access “Change data download. The phrase “No Listings“ will be replaced system settings” and choose “Yes, but my channel lineup is with program information during the next download cycle, incorrect,” and then reselect the correct lineup. which will occur within the next 24-hour period. b) Channel line-up changes have not yet been processed. Use the “Change channel display” feature to make adjustments. 17. Q: Why do some of my channels display “No Listing?” c) Initial setup was done incorrectly (that is, the wrong A: There are several possibilities: ZIP/postal code was entered.) Redo the initial setup. a) The channels in question were recently turned ON (in Change channel display) and TV Guide On Screen® has 24. Q: Why doesn’t the program highlighted match up with yet to receive its next data download. the video window on my TV screen? b) After completing the initial setup, the first data download A: There are several possibilities (see page 65 for details): of the day was interrupted by a VCR recording. a) The station in question made a late change to its scheduled c) The TV power cord was left unplugged for an extended program listing and the TV Guide On Screen® system has period of time and the TV Guide On Screen® system was not yet been updated. unable to receive program listings during the scheduled download cycle. b) The TV is receiving broadcasts through a modified or d) Poor reception caused some of the data to be missed. boosted antenna system or a satellite dish (not supported by the TV Guide On Screen® system). e) The cable box was turned OFF. The TV power cord must be plugged in and the cable box must be ON. c) Initial setup was done incorrectly. (i.e., the wrong ZIP/postal code was entered.) Redo the initial setup. g) A/V Cable: The VCR was turned OFF. If the connection includes stereo cables with cable box to VCR and stereo d) Incorrect channel lineup was selected. Access “Change connection from VCR to television, the VCR must be ON. system settings” and choose “Yes, but my channel lineup is incorrect,” and then reselect the correct lineup.) 18. Q: A show entry in the TV Guide On Screen® system reads e) The video window may be locked. Press SPLIT to unlock. “No Listing.” What does that mean? A: Show information for that entry was not available during 25. Q: Can I move my favorite stations to the top of the the last TV Guide On Screen® system information update TV Guide On Screen® display screen? (download). Show information is updated on a daily basis. A: Yes. Use the “Change channel display” feature to make adjustments (see page 65). Highlight the station call letters 19. Q: I have seen the word “download” in reference to the TV to be moved, then use the BLUE, GREEN, and/or Guide On Screen system. What does that mean? Number buttons to reassign the position of the station. A: “Download” refers to the times throughout the day when the TV Guide On Screen® system is receiving channel and listings information from your Cable or over-the-air antenna transmission. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 101 HM95_R2_097-102_061505 101 6/27/05, 6:29 PM

Chapter 10: Troubleshooting TV Guide On Screen® FAQs (continued) OPERATIONS 32. Q: Is Help available in the TV Guide On Screen® system? If so, how do I find it? 26. Q: How can I look for a specific show in the TV Guide On Screen® system? A: Yes. Highlight any of the five main Services (Listings, Schedule, Recordings, Setup, Search) and press the INFO A: SEARCH lets you find shows by keyword, alphabetically, key on the remote control. An expanded Info Box displays or by category (HDTV, Movies, Sports, Children, additional help information. Press INFO again to close Educational, News, Variety, Series). the box. 27. Q: My cable box will not change channels with the Help is also available in a panel menu. Press INFO to TV Guide On Screen® system. What’s wrong? display an expanded Info Box. Press INFO again to close the box. A: There are several possibilities: a) The incorrect cable box code was entered during TV Guide RECORD/REMIND On Screen® initial setup. Redo initial setup. 33. Q: Can I tune to a different channel while recording a b) The G-LINK® (IR blaster) cable may not be connected program? properly (see page 25). A: No. c) The cable box has no remote capability and is incompatible. 34. Q: How many programs can be scheduled for RECORD in the GUIDE? 28. Q: How do I resize or close the Info window? A: There is no limit to the number of shows that can be A: Press the INFO button on the remote control to resize the programmed into the schedule memory. Info window. Press the INFO button again to close the 35. Q: If a program is scheduled to RECORD on a Regular Info window. basis, does it count as five? 29. Q: Is there a way to go directly to the next day’s listings A: No, whether a program is scheduled ONCE, without scrolling through each time slot? REGULARLY, or WEEKLY, it only counts as one show in the RECORD stack memory. A: Yes. In LISTINGS, highlight the station you want to look ahead and use the Channel Number buttons on the remote 36. Q: If I have a power failure, will I need to reset the control to enter “24.” In the resulting menu, press z two recorded shows I have already programmed? times to scroll down to select the HOURS AHEAD A: The start times and channel numbers of shows that have option, and then press ENTER. You also can use the been programmed will be retained in the memory of the SKIP/SEARCH button on the remote control. TV Guide On Screen® system. Titles will appear once listings are restored. 30. Q: Why can’t I record a show? All I get is snow or a blue screen. 37. Q: Can I set a Record or Remind event without A: There are several possibilities (without a cable box): highlighting a show title in the TV Guide On Screen® system? a) The recording unit was not connected or set up correctly. A: Yes. TV Guide On Screen® has a Manual Record and b) The incorrect channel lineup was selected. Press GUIDE Remind feature. Highlight SCHEDULE in the Service Bar, and then • to highlight SETUP. Press z to highlight and press MENU. Choose the event type, press ENTER, “Change system settings,” and then press ENTER. Follow and then enter the date, start and stop time, channel the on-screen prompts to select the correct channel lineup. number, and so forth. 31. Q: Why won’t my VCR change channels and why does it 38. Q: What do the frequencies for Record and Remind mean? change to the wrong channel? A: Once—records/reminds the show one time. A: There are two possibilities (with a cable box): Daily (manual only)—records the time, channel, input, a) The VCR is not set on the correct output channel. Set the recorder combination Monday through Friday. VCR to 03, 04, or whichever output channel is set by your cable system. Regularly— records/reminds the show every time the show airs on the same channel and starts at the same time. b) The VCR and/or cable box are hooked up incorrectly. Refer to your VCR owner’s manual or contact your Cable Weekly— records/reminds the show each time the show TV company for proper wiring procedures. airs on the same day of the week, on the same channel and starts at the same time. Off (not cancel)—keeps the show in the Schedule list but will not record/remind the show until the frequency is changed. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 102 HM95_R2_097-102_061505 102 6/27/05, 6:29 PM

11 Appendix Lamp unit replacement and care Replacing the lamp unit When to replace the lamp unit (User-replaceable component) You should replace the lamp unit: • if the picture darkens and/or colors fade; WARNING: RISK OF • if the screen (lamp) does not light (LED indication #3, page ELECTRIC SHOCK! 99); or TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER • if you hear a loud noise and the picture goes black, which REMOVE TV COVERS, EXCEPT AS SPECIFIED may indicate a lamp rupture (LED indication #3, page 99). HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. To obtain a replacement lamp unit: Failure to follow this WARNING may result in death or serious injury. Web Contact In warranty www.tacp.toshiba.com/service Call toll-free The light source for this TV is a mercury lamp with internal 1-800-631-3811. atmospheric pressure that increases during use. The lamp has a Out of www.ceaccessories.toshiba.com Consult your limited service life that varies depending on product use and warranty consumer user settings. electronics dealer for availability. As is generally the case with all projection TVs that use projection lamps as a light source, the brightness of the lamp in Use the replacement lamp unit model listed below only. this TV may vary somewhat over the expected service life and Using any other lamp may cause damage to the TV will generally decrease over time. The average useful service life and/or lamp. for the lamp is approximately 8,000 hours in Low Power mode or 6,000 hours in High Bright mode. See “Selecting the Lamp CAUTION: Always replace with same mode” on page 75 for information on switching the lamp mode. type lamp unit: Model No. D95-LMP Because these are averages, some lamps will require earlier replacement. (Stock no. 23311153) Note : The lamp is warranted only for the periods and to the extent set forth in the Limited Warranty applicable to this set, which is a substantially shorter period of time than the average useful service period. See “Limited United States Warranty” on page 107. If you use the lamp beyond its service life: • you may notice a reduction in the colors and/or brightness of the picture; and • the strength of the quartz glass in the lamp will be reduced and the lamp may rupture (often making a loud noise when this happens). If the lamp ruptures, the TV will not operate until the lamp unit is replaced. CAUTION: Always handle the lamp unit with care. The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 103 HM95_R2_103-109_061505 103 6/27/05, 6:40 PM

Chapter 11: Appendix Lamp unit replacement and care (continued) How to replace the lamp unit 4. Using a manual Phillips screwdriver, loosen the two screws on the lamp unit. WARNING: RISK OF ELECTRIC SHOCK! TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury. Required tools: • Manual Phillips screwdriver Lamp unit screws • Soft, lint-free gloves. Optional tool: 5/32” or 4mm Allen wrench. WARNING: RISK OF ELECTRIC SHOCK! 1. Turn off the TV and unplug the power cord. The lamp unit door is provided with an interlock to reduce the risk of electric shock and excessive WARNING: Eye damage may result from ultraviolet radiation. Never defeat its purpose or attempt directly viewing the light produced by this to service without removing the lamp unit door lamp. Always turn off the TV and unplug the completely. Failure to follow this WARNING may result in power cord before opening the lamp unit door. death or serious injury. 2. STOP! Allow the lamp to cool for at least one (1) hour before replacing it. 5. Grasp the lamp unit handle and gently pull the lamp unit CAUTION: HOT SURFACE! straight out of the TV. Set the old lamp unit aside (see The temperature of the lamp “Disposing of the used lamp unit” on page 105). immediately after use exceeds 392°F (200°C). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT. 3. On the lamp unit door on the side of the TV, loosen the thumb screw by hand or by using a 5/32” or 4mm Allen wrench, and then remove the lamp unit door. TV back Note: Wear soft, lint-free gloves when replacing the lamp unit. Thumb screw Lamp unit door detail Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 104 HM95_R2_103-109_061505 104 6/27/05, 6:40 PM

Chapter 11: Appendix Lamp unit replacement and care (continued) How to replace the lamp unit (continued) 8. Reattach the lamp unit door, making sure to insert the hooks on the left side of the lamp unit door inside the opening in the TV cabinet. 6. Carefully insert the new lamp unit straight into the TV until it is fully seated. Insert the hooks inside the TV cabinet opening. Lamp unit door 9. Replace the thumb screw and hand-tighten. Note : Thumb screw • Never subject the lamp unit to excessive shock. (hand-tighten only) • Never touch the lamp unit glass or otherwise get it dirty. Doing so may affect the image quality and reduce the service life of Lamp unit door NOTE : Make sure the lamp. See “Cleaning the lamp unit glass” below. the lamp unit door is installed securely; otherwise, the TV may not turn on. CLEANING THE LAMP UNIT GLASS If you accidentally touch the lamp unit glass or otherwise 10. Plug in the power cord and turn on the TV. After the initial get it dirty, wipe it with a lint-free lens cleaning cloth (such warmup period (which may take several seconds for full as a cloth for cleaning camera lenses or eyeglasses). picture brightness), the TV should operate normally. If any of the following conditions exist, turn off the TV, unplug the CAUTION: NEVER clean a hot lamp with power cord, and repeat steps 1–9 to ensure that the lamp unit any type of flammable liquid or aerosol and lamp unit door are installed correctly: cleaning agent. Many ordinary cleaning agents (such as glass cleaners) contain chemicals that may be • No picture • Dark picture • TV will not turn on flammable at certain temperatures. If the lamp unit is not allowed If, after repeating steps 1–9, the problem still exists: to cool for at least one (1) hour, such chemicals may ignite. Call TACP Consumer Solutions at 1-800-631-3811. 7. Using a manual Phillips screwdriver, tighten the two lamp unit screws. Disposing of the used lamp unit Note: Hand-tighten only. Do not use an electric screwdriver. • Place the used lamp unit in the empty box from the new unit. • Keep the lamp unit out of reach of children and pets. CAUTION: Always handle the lamp unit with care. The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional or accidental abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points. • Dispose of the used lamp unit by the approved method for your area. Lamp unit screws NOTE : The lamp unit contains mercury. Disposal of mercury may (use manual Phillips screwdriver only) be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries NOTE : Make sure the lamp unit and screws Alliance (www.eiae.org). are installed securely; otherwise, the TV may not turn on and the lamp life may be shortened. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 105 HM95_R2_103-109_061505 105 6/27/05, 6:40 PM

Chapter 11: Appendix Specifications NOTE: • This model complies with the specifications listed below. • Designs and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future. Television System Video/Audio Terminals (continued) NTSC standard HDMI™ INPUT: ATSC standard (8VSB) HDMI compliant (type A connector) Digital Cable (64 QAM, 256 QAM; in-the-clear, unencrypted*) HDCP compliant *Encrypted channels can be viewed on this TV E-EDID** compliant using a CableCARD.™ See page 12 for details. Suggested formats: 1080i, 480p, 480i, 720p HDMI Audio: 2-channel PCM; 32/44.1/48 kHz sampling Channel Coverage frequency; 16/20/24 bits per sample VHF: 2 through 13 NOTE: This TV does not provide HDMI OUTPUT. UHF: 14 through 69 Cable TV: Mid band (A-8 through A-1, A through I) VIDEO/AUDIO OUTPUT (also for recording): Super band (J through W) VIDEO: 1 V(p-p), 75 ohm, negative sync. Hyper band (AA through ZZ, AAA, BBB) AUDIO: 150 mV(rms) (30% modulation equivalent, Ultra band (65 through 94, 100 through 135) 2.2 k ohm or less) VARIABLE AUDIO OUTPUT: Power Source 0–300 mV(rms) (30% modulation equivalent, 120 V AC, 60 Hz 2.2 k ohm or less) Power Consumption G-LINK® and IR OUTPUT: 240 W (average) 3 V(p-p), 3.5 mm mono socket (IR blaster cables supplied) 38 W in standby mode (using a CableCARD™) IEEE1394 INPUT/OUTPUT: 34 W in standby mode (without a CableCARD™) IEEE1394 compliant 4-pin Audio Power DIGITAL AUDIO OUTPUT: 15 W + 15 W Optical type Speaker Type Dimensions Main: Two 4-inch (10cm) round 46HM95: Width: 53-1/8 inches (1349 mm) Tweeter: Two 1-5/8-inch (4cm) round Height: 31-13/16 inches (808 mm) Depth: 15-1/4 inches (387 mm) Video/Audio Terminals 52HM95: Width: 58-3/8 inches (1483 mm) S-VIDEO INPUT: Height: 35-1/16 inches (891 mm) Y : 1 V(p-p), 75 ohm, negative sync. Depth: 15-1/4 inches (387 mm) C : 0.286 V(p-p) (burst signal), 75 ohm 62HM95: Width: 67-1/16 inches (1703 mm) Height: 40-15/16 inches (1040 mm) VIDEO/AUDIO INPUT: Depth: 18-3/16 inches (462 mm) VIDEO: 1 V(p-p), 75 ohm, negative sync. AUDIO: 150 mV(rms) (30% modulation equivalent, Weight 22 k ohm or greater) 46HM95: 78 lbs (35.38 kg) ColorStream® (component video) HD INPUT: 52HM95: 83 lbs (37.65 kg) Y : 1V(p-p), 75 ohm 62HM95: 99 lbs (44.90 kg) PR: 0.7 V(p-p), 75 ohm Supplied Accessories PB : 0.7 V(p-p), 75 ohm • Two dual-wand IR blaster cables AUDIO: 150 mV(rms), 22 k ohm or greater • Remote control with two size “AA” alkaline batteries Suggested formats: 1080i, 480p, 480i, 720p • Owner’s Manual (this book) NOTE: This TV does not provide ColorStream HD OUTPUT. Optional Stands 46HM95: ST4665 52HM95: ST5265 62HM95: ST6265 _________ ** E-EDID = Enhanced-Extended Display Identification Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 106 HM95_R2_103-109_061505 106 6/27/05, 6:40 PM

Chapter 11: Appendix Limited United States Warranty for DLP™ Television Models Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following Your Responsibility limited warranties to original consumers in the United States. THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONDITIONS: CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP™ (1) You must retain your original bill of sale or provide other proof of TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER purchase.. (2) All warranty servicing of this DLP™ Television must be performed by an PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. Authorized TACP Service Station. DLP™ TELEVISIONS PURCHASED IN THE U.S.A. AND USED ANYWHERE (3) The warranties from TACP are effective only if this DLP™ Television is OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA purchased and operated in the Continental U.S.A. or Puerto Rico. AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES. (4) Labor service charges for set installation, setup, adjustment of customer controls, and installation or repair of antenna systems are not covered DLP™ TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., by this warranty. Reception problems caused by inadequate antenna INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO, AND USED systems, misaligned satellite dishes, cable television distribution, VCRs, IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES. DVD players/recorders, personal computer level IEEE1394 devices, and any other connected signal source device are your responsibility.. (5) Warranties extend only to defects in materials or workmanship as limited Limited One (1) Year Warranty on Parts and Labor above, and do not extend to any DLP™ Television or parts that have TACP warrants this DLP™ Television and its parts against defects in materials been lost or discarded by you or to damage to the DLP™ Television or or workmanship for a period of one (1) year after the date of original retail parts caused by fires, misuse, accident, Acts of God (such as lightning purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION, or fluctuations in electric power), improper installation, improper REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR maintenance, or use in violation of instructions furnished by TACP; use REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR or malfunction through simultaneous use of this DLP™ Television and LABOR. During this period, TACP Authorized Service Station personnel will connected equipment; or to units that have been modified or had the come to your home when warranty service is required. Depending on the serial number removed, altered, defaced, or rendered illegible. type of repair required, the service will either be performed in your home or How to Obtain Warranty Service the DLP™ Television will be taken to a TACP Authorized Service Station for If, after following all of the operating instructions in this manual and reviewing repair and returned to your home at no cost to you. the section titled “Troubleshooting,” you find that service is needed: Limited One (1) Year Warranty on Lamp Unit (1) To find the nearest TACP Authorized Service Station, visit TACP’s website at www.tacp.toshiba.com/service or contact TACP’s TACP warrants the original lamp unit contained in this DLP™ Television Consumer Solution Center toll free at 1-800-631-3811. against defects in materials or workmanship for a period of one (1) year after (2) You must present your original bill of sale or other proof of purchase to the date of original retail purchase. DURING THIS PERIOD, TACP WILL, the TACP Authorized Service Station. AT TACP’S OPTION, EXCHANGE A DEFECTIVE LAMP UNIT WITH A NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO YOU. For additional information, visit TACP’s web site: LABOR CHARGES FOR LAMP UNIT REPLACEMENT ARE YOUR www.tacp.toshiba.com. RESPONSIBILITY AND ARE NOT COVERED UNDER THIS ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE WARRANTY. The lamp unit is a user-replaceable component. U.S.A., INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, Rental Units ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED The warranty for DLP™ Television rental units begins on the date of the first WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY rental or thirty (30) days after the date of shipment to the rental firm, WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A. AS whichever comes first. HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH RESPECT TO THE Limited Warranty for Commercial Units REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL TACP warrants DLP™ Televisions, including the lamp units contained therein, TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES that are sold and used for commercial purposes as follows: all parts are (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, BUSINESS warranted against defects in materials or workmanship for a period of ninety INTERRUPTION, OR MODIFICATION OR ERASURE OF RECORDED (90) days after the date of original retail purchase. DURING THIS PERIOD, DATA CAUSED BY USE, MISUSE OR INABILITY TO USE THIS DLP™ TACP WILL, AT TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE TELEVISION). PART WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO No person, agent, distributor, dealer, or company is authorized to change, YOU. modify, or extend the terms of these warranties in any manner whatsoever. The time within which an action must be commenced to enforce any Owner’s Manual and Product Registration obligation of TACP arising under the warranty or under any statute or law of Read this owner’s manual thoroughly before operating this DLP™ television. the United States or any state thereof is hereby limited to ninety (90) days from the date you discover, or should have discovered, the defect. This Complete and mail the enclosed product registration card or register your limitation does not apply to implied warranties arising under the law of any DLP™ Television online at www.tacp.toshiba.com/service as soon as state of the U.S.A. possible. By registering your DLP™ Television you will enable TACP to bring THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU you new products specifically designed to meet your needs and help us to MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE contact you in the unlikely event a safety notification is required under the TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW Consumer Product Safety Act. Failure to register your product does not LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, diminish your warranty rights. WHEN AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES. 05 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 107 HM95_R2_103-109_061505 107 6/27/05, 6:40 PM

Chapter 11: Appendix A copy of the GPL source code in this product may be obtained by THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND contacting Toshiba Consumer Solutions at (800)631-3811. There will be a ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT charge to cover the costs of providing the source code. LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT A copy of the LGPL source code in this product may be obtained by SHALL THE OpenSSL PROJECT OR CONTRIBUTORS BE LIABLE FOR ANY contacting Toshiba Consumer Solutions at (800)631-3811. There will be a DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR charge to cover the costs of providing the source code. CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, USB Protocol Copyright © 2005 The NetBSD Foundation, Inc. All rights PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, reserved. DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT Redistribution and use in source and binary forms, with or without LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) modification, are permitted provided that the following conditions are ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF met: ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes 1. Redistributions of source code must retain the above copyright notice, cryptographic software written by Eric Young ([email protected]). This this list of conditions and the following disclaimer. product includes software written by Tim Hudson ([email protected]). 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation Copyright © 1995-1998 Eric Young ([email protected]). All Rights reserved. and/or other materials provided with the distribution. This package is an SSL implementation written by Eric Young 3. Neither the name of The NetBSD Foundation nor the names of its ([email protected]). The implementation was written so as to conform with contributors may be used to endorse or promote products derived from Netscapes SSL. This library is free for commercial and non-commercial use this software without specified prior written permission. so long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, Ihash, DES, THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. etc., code; not just the SSL code. The SSL documentation included with this AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED distribution is covered by the same copyright terms except that the holder is WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED Tim Hudson ([email protected]). WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A Copyright remains Eric Young’s, and as such any Copyright notices in the PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE code are not to be removed. If this package is used in a product, Eric FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, Young should be given attribution as the author of the parts of the library INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL used. This can be in the form of a textual message at program startup or in DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF documentation (online or textual) provided with the package. SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; Redistribution and use in source and binary forms, with or without OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY modification, are permitted provided that the following conditions are met: THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR 1. Redistributions of source code must retain the copyright notice, this list of TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY conditions and the following disclaimer. WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 2. Redistributions in binary form must reproduce the above copyright notice, POSSIBILITY OF SUCH DAMAGE. this list of conditions and the following disclaimer in the documentation This product includes software developed by the OpenSSL Project for use in and/or other materials provided with the distribution. the OpenSSL Toolkit (http://www.openssl.org). 3. All advertising materials mentioning features or use of this software must This product includes cryptographic software written by Eric Young display the following acknowledgement: “This product includes ([email protected]). cryptographic software written by Eric Young ([email protected]).” The OpenSSL 0.9.7d Copyright © 1998-2000 the OpenSSL Project. All Rights word ‘cryptographic’ can be left out if the routines from the library being reserved. Redistribution and use in source and binary forms, with or without used are not cryptographic related. modification, are permitted provided that the following conditions are met: 4. If you include any Windows specific code (or derivative thereof) from the 1. Redistributions of source code must retain the above copyright notice, apps directory (application code) you must include an acknowledgement: this list of conditions and the following disclaimer. “This product includes software written by Tim Hudson 2. Redistributions in binary form must reproduce the above copyright notice, ([email protected]).” this list of conditions and the following disclaimer in the documentation THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY and/or other materials provided with the distribution. EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 3. All advertising materials mentioning features or use of this software must TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS display the following acknowledgement: This product includes software FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL developed by the OpenSSL Project for use in the OpenSSL Toolkit THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, (http://openssl.org). INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 4. The names “OpenSSL Toolkit” and “Open SSL Project” must not be used DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF to endorse or promote products derived from this software without prior SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; written permission. For written permission, please contact openssl- OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY [email protected] THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR 5. Products derived from this software may not be called “OpenSSL” nor may TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY “Open SSL” appear in their names without prior written permission of the WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE OpenSSL Project. POSSIBILITY OF SUCH DAMAGE. The license and distribution terms for 6. Redistributions of any form whatsoever must retain the following any publicly available version or derivative of this code cannot be changed, acknowledgement: “This product includes software developed by the i.e. this code cannot simply be copied and put under another distribution OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org).” license (including the GNU Public License). Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 108 HM95_R2_103-109_061505 108 6/27/05, 6:40 PM

Chapter 11: Appendix Notes Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 109 HM95_R2_103-109_061505 109 6/27/05, 6:40 PM

Index A EFGHIJ Antenna cables ......................................................................... 11 EIA-775 ......................................................................................... 22 Audio player ............................................................................... 87 FAV SCAN button .............................................................. 44, 78 Audio quality adjustments .................................................... 85 Factory defaults, restore TV .......................................... 52, 79 Audio system connection ...................................................... 20 Favorite channels .............................................................. 44, 78 Auto aspect ................................................................................. 74 Features, TV ................................................................................... 7 Auto power off ........................................................................... 92 Focus ............................................................................................. 86 AVHD ..................................................................................... 23, 50 Front of the TV .............................................................................. 9 B Front panel lock ........................................................................ 96 Back of the TV ........................................................................... 10 Front panel touch pad ....................................................... 9, 36 Blocking channels .................................................................... 95 GameTimer™ .............................................................................. 96 G-LINK® connection ............................................................... 25 C HDMI™ connection ................................................................. 19 Cable box connection ...................................................... 14, 16 IEEE1394 ...................................................................................... 22 CableCARD™ ............................................................................. 12 INPUT button ............................................................................. 67 CableClear™ DNR .................................................................... 80 Input lock ..................................................................................... 95 Cables ........................................................................................... 11 Installation, care, and service ............................................ 3, 4 Camcorder connection ........................................................... 13 Installation, setup ........................................................................ 8 CH yz buttons .................................................................. 42, 71 Integrated digital tuning ........................................................... 7 CH RTN button .......................................................................... 71 IR blaster ..................................................................................... 21 Channel Number buttons .............................................. 42, 71 JPEG ....................................................................................... 87–90 Channel programming: Automatic programming .................................................. 42 L Manually adding and deleting ....................................... 43 Labeling video inputs ............................................................. 68 Cinema mode ............................................................................. 75 Lamp mode ................................................................................. 75 Closed captions ........................................................................ 82 Lamp unit replacement .............................................. 103–105 Color temperature .................................................................... 80 Language selection ................................................................. 41 ColorStream® ...................................................................... 10, 17 Last mode memory feature .................................................. 92 Connecting devices .......................................................... 12–25 LED indications ............................................................... 8, 9, 99 CompactFlash® memory cards ..................................... 87, 88 Locking video inputs ............................................................... 95 Component video cables ...................................................... 11 LOCKS menu .............................................................................. 93 Component video (ColorStream®) .............................. 10, 17 Channels, blocking ............................................................. 95 Enable rating blocking ...................................................... 94 D GameTimer™ ......................................................................... 96 Device connections .......................................................... 12–25 New PIN code ...................................................................... 93 Defaults, restore TV factory ................................................. 52 Unlocking programs temporarily .................................. 95 Digital Audio Out ...................................................................... 20 Video inputs, locking ......................................................... 95 Digital signal meter ................................................................. 52 DNR (Digital Noise Reduction) .......................................... 80 Dolby Digital ........................................................................ 20, 86 Double-window POP feature ............................................... 76 DVD player connection ................................................... 16, 17 D-VHS .................................................................................... 23, 50 DVI connection .......................................................................... 19 Dynamic Contrast ..................................................................... 81 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 110 HM95_R2_110-111_061505 110 6/27/05, 7:10 PM

Index (continued) M S Memory cards ..................................................................... 87–90 Safety, care, installation, and service ............................. 2–5 Memory Stick™ memory cards ..................................... 87, 88 SAP sound ................................................................................... 84 Menu system ....................................................................... 35, 36 Satellite receiver connection ............................................... 15 MMC memory cards ......................................................... 87, 88 Sub-bass (SBS) ......................................................................... 85 MP3 ......................................................................................... 87–90 Scrolling the TheaterWide® picture ................................... 74 MPEG-2 digital video signals .............................................. 22 SD (Secure Digital™) memory cards .......................... 87, 88 MPEG Noise Reduction ......................................................... 81 Service ............................................................................................. 4 MTS feature ................................................................................ 84 Setup, TV ............................................................................... 36, 41 MUTE button .............................................................................. 84 Setup, TV Guide On Screen® system ................................ 37 Sleep timer .................................................................................. 91 OPQ Speakers ON/OFF .................................................................... 86 ON/OFF timer ............................................................................ 91 Specifications ........................................................................... 106 Optical audio cable ................................................................. 11 SRS 3D ......................................................................................... 86 Picture adjustments: SRS WOW ................................................................................... 86 Color temperature ............................................................... 80 StableSound® ............................................................................. 85 Picture mode ......................................................................... 79 Stereo sound .............................................................................. 84 Picture quality ....................................................................... 79 S-video cables ........................................................................... 11 Picture-out-picture (POP): Symbio™ AVHD recorder ............................................... 23, 50 FAV SCAN button ................................................................ 78 System status ............................................................................. 52 SPLIT button .......................................................................... 76 Picture scroll ............................................................................... 74 T Picture size selection .............................................................. 73 TheaterNet™ DEVICE and CONTROL buttons ............. 46 Picture viewer ............................................................................ 87 TheaterNet™ control ............................................................... 21 Problems with TV ............................................................... 97, 98 TheaterNet™ setup .................................................................. 45 Quick Restart ............................................................................. 51 TheaterWide® picture size .................................................... 73 Time and date setting ............................................................. 50 R Troubleshooting .................................................................. 97, 98 RECALL button ......................................................................... 84 TruBass ......................................................................................... 86 Remote control: TV Guide On Screen® .................................................. 8, 37, 53 Battery installation .............................................................. 28 Device code table ........................................................ 33, 34 V Effective range ...................................................................... 27 V-Chip blocking (Locks menu) .................................... 93–95 Functional key chart .................................................... 29, 30 VCR connection ................................................................. 13–18 Learning about the buttons ............................................ 26 Video cables ............................................................................... 11 Operational feature reset ................................................. 32 Video input labels .................................................................... 68 Programming ........................................................................ 31 Video input lock ........................................................................ 95 Searching and sampling the code ............................... 31 Volume lock feature ........................................................... 32 Restart, Quick ............................................................................ 51 W, X Restore TV factory defaults .................................................. 52 Warranty ..................................................................................... 107 WOW, SRS ................................................................................... 86 xD-Picture Card™ ............................................................... 87, 88 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 111 HM95_R2_110-111_061505 111 6/27/05, 7:10 PM

TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. HEAD OFFICE: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A. NATIONAL SERVICE DIVISION:1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A. MANUFACTURED BY TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C. GameTimer, SurfLock, Symbio, and TheaterNet are trademarks of Toshiba America Consumer Products, L.L.C. Digital Light Processing, DLP™ and the DLP medallion are trademarks of Texas Instruments. PRINTED IN USA (05-06) [A-PDFO] Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 23566650A HM95_R2_112_061505 112 6/27/05, 6:41 PM