Frigidaire FFRH2522R2 FFRH1822R2 FFRH1222R2 Manual

Wednesday, March 29, 2017
Download

All about the Use & Care of your Room Air Conditioner TA B L E O F C O N T E N T S Important Safety Instructions ............................... 2-3 Operating Instructions ......................................... 5-11 Product Registration ............................................. 4 Care and Cleaning .............................................. 11 Packaging ........................................................... 4 Energy Saving Ideas ........................................... 11 Normal Sounds .................................................... 4 Before You Call ................................................... 12 Air Conditioner Features ....................................... 5 Major Appliance Limited Warranty ........................ 13 16120300A00439 (June 2009) www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

Important Safety Instructions NOTE: This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance. NOTE: WARNING The power supply cord with For Your Safety this air conditioner contains a current Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any detection device designed to reduce the risk other appliance. Read product labels for flammability and other warnings. of fire. Please refer to the section ‘Operation of Current Device’ for details. WARNING In the event that the power supply cord is damaged, it cannot be repaired. It must be Prevent Accidents replaced with a cord from the product To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, manufacturer. follow basic precautions, including the following: Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the WARNING grille. If the air conditioner is to be installed in a window, you will probably want to clean both Avoid fire hazard or electric shock. Do not sides of the glass first. If the window is a triple-track type with a screen panel included, use an extension cord or an adaptor plug. Do remove the screen completely before installation. not remove any prong from the power cord. Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and the installation instructions for possible future use in removing or reinstalling this unit. When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. 115V 230V 230V WARNING 15A 15A 20A Electrical Information The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements. Grounding Prong Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Do not, under any Your air conditioner must be used in a properly grounded wall receptacle. If the wall 230V circumstances, cut, receptacle you intend to use is not adequately grounded or protected by a time delay fuse 30A remove or bypass the or circuit breaker, have a qualified electrician install the proper receptacle. grounding prong. Do not run air conditioner without outside protective cover in place. This could result in mechanical damage within the air conditioner. Do not use an extension cord or an adapter plug. SAFETY PRECAUTIONS DANGER! Avoid Serious Injury or Death This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs. Do not insert or place fingers or objects into the air discharge area in the front of the unit. Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box. Do not cut or damage the power cord. If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer. In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized Electrolux servicer. Do not operate the air conditioner with wet hands. Do not pull on the power cord. Do not drink any water that is drained from the air conditioner. 2009 Electrolux Home Products, Inc. All rights reserved. 2

Important Safety Instructions SAFETY PRECAUTIONS CAUTION! Avoid Injury or damage to the unit or other property Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively. Do not climb on or place objects on outdoor part of the unit. Do not hang objects off the unit. Do not place containers with liquids on the unit. Turn off the air conditioner at the power source when it will not be used for an extended period of time. Periodically check the condition of the unit’s installation accessories for any damage. Do not apply heavy pressure to the radiator fins of the unit. Operate the unit with air filter in place. Do not block or cover the intake grille, discharge area and outlet ports. Ensure that any electrical/electronic equipment is one yard away from the unit. Do not use or store flammable gases near the unit. Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock. When cleaning the unit, first make sure that the power and circuit breaker are turned off. READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER. Unit must be upright for one hour prior to operating. The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: Plug in the Air Conditioner. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out. Plug in & Press the RESET button. Again you will notice a click as the button engages. press RESET The power supply cord is now supplying electricity to the unit. (This is also indicated by a light on the plug head). NOTE: Do not use this device to turn the unit on or off. Always make sure the RESET button is pushed in for correct operation. The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. 2009 Electrolux Home Products, Inc. All rights reserved. 3

Product Registration, Packaging & Normal Sounds Product Registration Record Your Model and Serial Numbers Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the outside of the cabinet. Model No. Serial No. Register Your Product The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company. Packaging Remove all packaging from inside the carton, along with any inserts placed into the side louvers. Remove the plastic ties and foam pad that secure the compressor to the fan shroud (where applicable). See diagram. foam pad + plastic ties Packing Inserts Normal Sounds High pitched Chatter Today’s high efficiency compressors may have a high pitched chatter Vibration during the cooling cycle. Unit may vibrate and make noise because of poor wall or window Sound of Rushing Air construction or incorrect installation. At the front of the unit, you may hear the sound of rushing air being moved by the fan. Pinging or Swishing Droplets of water hitting condenser during normal operation may cause “pinging or swishing” sounds. Note: Don’t try to drill any holes on the base pan to eliminate the Gurgle/Hiss normal sounds, otherwise it will “Gurgling or hissing” noise may be void the warranty. heard due to refrigerant passing through evaporator during normal operation. 2009 Electrolux Home Products, Inc. All rights reserved. 4

Air Conditioner Features & Operating Instructions ELECTRONIC CONTROL Air Conditioner Features Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you CLEAN AIR REMOTE TEMP desire. The unit can be controlled by the touch pad alone or with the remote. FEATURE SENSING INDICATOR DISPLAYS (some models) (some models) TEMPERATURE/TIME CHECK FILTER RESET BUTTON ACTIVATES TURNS UNIT SLEEP MODE TIMER ON OR OFF ADJUSTS SETS FAN SETS MODE TEMPERATURE SPEED OR TIME Battery Size: AAA Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel- cadmium) batteries. STANDARD REMOTE FOR HEAT MODELS w/DISPLAY & REMOTE SENSING BUTTON Operating Instructions NOTE The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control. TO TURN UNIT ON: YOU WILL SEE: Note: The unit will run in energy saver(econ) mode when used for the first time. In this mode, the fan will continue to DO THIS: run for 1 minute after the compressor shuts off. The fan then PRESS ON/OFF BUTTON cycles on for 20 seconds at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on. 2009 Electrolux Home Products, Inc. All rights reserved. 5

Operating Instructions Operating Instructions (continued) TO CHANGE TEMPERATURE SETTlNG: YOU WILL SEE: DO THIS: Note: Tap or hold either up ( ) or down ( ) button until the desired temperature is seen on the display. This tempe- PRESS TO RAISE rature will be automatically maintained anywhere between PRESS TO LOWER 60 °F (16 °C) and 90 °F (32 °C) . If you want the display to read the actual room temperature. See "To Operate on Fan Only" section on Page 7. TO ADJUST FAN SPEEDS: YOU WILL SEE: DO THIS: PRESS TO SELECT TO USE AUTO FAN FEATURE: YOU WILL SEE: DO THIS: Note: Fan starts at High Speed and adjusts to a slower speeds the room temperature dictates. For example, if the PRESS FAN BUTTON, room doesn't get too warm, it will stay at the slowest speed. CHOOSE AUTO If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. Press either the fan slower or fan faster button to adjust the fan speed manually. 2009 Electrolux Home Products, Inc. All rights reserved. 6

Operating Instructions Operating Instructions (continued) TO OPERATE ON FAN ONLY: YOU WILL SEE: Note: Use this function only when cooling is not desired, DO THIS: such as for room air circulation or to exhaust stale air on PRESS some models. (Remember to open the vent during this MODE BUTTON function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you CHOOSE prefer. (Except “Auto Fan”). FAN ONLY During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. COOL FEATURE: YOU WILL SEE: Note: In this mode, the fan remains on all the time with the DO THIS: compressor cycling on and off when room temperature is reached. PRESS MODE BUTTON CHOOSE COOL SLEEP FEATURE: YOU WILL SEE: Note: In this mode the selected temperature will increase DO THIS: by 2 °F 30 minutes after the mode is selected. The tempe- PRESS rature will then increase by another 2 °F after an additional SLEEP BUTTON 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected tempera- ture. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button. 2009 Electrolux Home Products, Inc. All rights reserved. 7

Operating Instructions Operating Instructions (continued) TIMER: DELAY STOP / START FEATURE YOU WILL SEE HOW MUCH TIME IS CHOSEN: THEN FIRST DO THIS: DO THIS: PRESS PRESS TIMER BUTTON UP/DOWN BUTTONS Note: For Delay Stop, the unit must be in the On position. Note: For Delay Start, the unit must be in the Off position. First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool, Energy Saver, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. To change the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens the above steps have to be repeated again. CHECK FILTER FEATURE, YOU WILL SEE: Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The LED (light) will illuminate after 250 hours of operation. To reset DO THIS: after cleaning the filter, press the "Filter Reset" button and PRESS FILTER the light will go off. RESET BUTTON CLEAN AIR FEATURE(on some models): Note: When this feature is "ON", the electronic air purifier is DO THIS: energized to remove pollen and impurities from the air. To PRESS cancel this feature, press the Clean Air button (the LIGHT CLEAN AIR will turn off). BUTTON Note: This feature can be activated on the unit touch pad ONLY. 2009 Electrolux Home Products, Inc. All rights reserved. 8

Operating Instructions Operating Instructions (continued) REMOTE SENSING FEATURE (on some models): LIGHT pulsing ( On & Off intermittently ). DO THIS: PRESS REMOTE SENSING START BUTTON NOTE: Unit display shows the set temperature NOTE: Remote display is actual temperature Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode. at remote control only To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use the “ ” buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit itself ). The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. lt will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. lf the unit does not receive the remote sensing signal during any 3 minute interval, the unit will beep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY. NOTE: The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON/OFF button on the unit. HEATING FEATURE(on some models): YOU WILL SEE: Note: This feature can be used with any combination of FAN DO THIS: Speeds (Low speed only on 115V models), Timer, or Sleep Modes. When in the "Heat" mode,the fan will run continuously PRESS MODE BUTTON, while heat is needed. The temperature will automatically be CHOOSE HEAT maintained anywhere between 55 °F(13 °C) and 80 °F(27 °C) (The upper limit of temperature could reach 86°F(30 °C) on some of the 115V models.). When the room set temperature is satisfied, the fan will cycle off and on to circulate and sample the room air. FAULT CODES: If the display reads "HS", ”AS”, ”ES”, ”CS” or ”OS”, a sensor has failed. Contact your Authorized Frigidaire Service Center. 2009 Electrolux Home Products, Inc. All rights reserved. 9

Operating Instructions Operating Instructions (continued) TO CHANGE TEMPERATURE DISPLAY: YOU WILL SEE: DO THIS: Note: The control is capable of displaying temperature in PRESS AND HOLD THE degrees Fahrenheit or degrees Celsius. UP/DOWN BUTTONS TOGETHER FOR 3 SECONDS TO TURN UNIT OFF: YOU WILL SEE: Note: If the unit is turned off in heat mode (if applicable) or DO THIS: fan only mode, it will return to the same setting when it is PRESS turned on again. When the unit is turned off in cool or energy ON/OFF BUTTON saver(econ) mode, it will run in energy saver(econ) mode when it is turned on again, but the setting of temperature and fan speed will remain. ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with. The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time. There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of having to roll through to select another mode. The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees in cool mode, 55F and 80F degrees in heat mode(the upper limit of temperature could reach 86F degrees on some of the 115V models). After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored. Fresh Air Vent Control (on some models) The Fresh Air Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (see Fig. 1) 2. Draw fresh air into the room - Fresh Air (see Fig. 2) 3. Exchange air from the room - Vent Open (see Fig. 3) Figure 1 (VENT CLOSED) Figure 2 (FRESH AIR) Figure 3 (VENT OPEN) 2009 Electrolux Home Products, Inc. All rights reserved. 10

Operating Instructions, Care and Cleaning & Energy Saving Ideas Operating Instructions (continued) Air Directional Louvers AUGER WHEELS Air directional louvers control air flow direction. Your air conditioner has the louver type described below. Auger Type The louvers will allow you to direct the air flow Up or Down and Left or Right throughout the room as needed. Rotate the Auger Wheels until the desired Left/Right direction is obtained. Pivot horizontal louvers until the desired (8-WAY) Up/Down direction is obtained. Care and Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards. Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils. Push the vent handle to the Vent Closed position(where applicable). Open the front panel. Grasp the filter by the center and pull up and out. Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing Or instead of washing, you may vacuum the filter clean. NOTE: When replacing the air filter after cleaning, make sure the tabs on the air filter are on the upper part of filter, and placed outward as shown in the drawing on the left side. Cabinet Cleaning Tab Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry. Never use harsh cleaners, wax or polish on the cabinet front. Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner. Plug in air conditioner. Air Filter Winter Storage If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton. Energy Saving Ideas Do not block air flow inside with blinds, curtains or furniture; or outside with shrubs, enclosures, or other buildings. The capacity of the room air conditioner must fit the room size for efficient and satisfactory operation. Install the room air conditioner on the shady side of your home. A window that faces north is best because it is shaded most of the day. Close the fireplace damper, floor and wall registers so cool air does not escape up the chimney and into the duct work. Keep blinds and drapes in other windows closed during the sunniest part of the day. Clean the air filter as recommended in the section “Care and Cleaning”. Proper insulation and weather stripping in your home will help keep warm air out and cool air in. External house shading with trees, plants or awnings will help reduce the air conditioner’s work load. Operate heat producing appliances such as ranges, washers, dryers and dishwashers during the coolest part of the day. 2009 Electrolux Home Products, Inc. All rights reserved. 11

Before You Call Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance. OCCURRENCE SOLUTION Air conditioner will not operate. Wall plug disconnected. Push plug firmly into wall outlet. Plug Current Device Tripped. Press the RESET button. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Control is OFF. Turn Control ON and set to desired setting. Air from unit does not feel cold Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above enough. 60°F (16°C). Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil. Reset to a lower temperature. Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode. Air conditioner cooling, but room Outdoor temperature below 60 O F (16 O C). To defrost the coil, set FAN ONLY mode. is too warm - ice forming Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY on cooling coil behind decorative mode. front Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a higher setting. Air conditioner cooling, but room Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section. is too warm - NO ice forming on Temperature is set too high. Set temperature to a lower setting. cooling coil behind decorative front. Air directional louvers positioned improperly. Position louvers for better air distribution. Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit. Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc. Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling, floor and furniture. Air conditioner turns on and off Dirty air filter - air restricted. Clean air filter. rapidly. Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils more frequently. Noise when unit is cooling. Air movement sound. This is normal. If too loud, set to lower FAN setting. Window vibration - poor installation. Refer to installation instructions or check with installer. Water dripping INSIDE when Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to unit is cooling. installation instructions or check with installer. Water dripping OUTSIDE when Unit removing large quantity of moisture from humid room. This is normal during excessively humid unit is cooling. days. Remote Sensing Deactivating Remote control not located within range. Place remote control within 20 feet & 120° radius of the Prematurely (some models). front of the unit. Remote control signal obstructed. Remove obstruction. Room too cold. Set temperature too low. lncrease set temperature. Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote control or deactivate remote sensing. If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service. 2009 Electrolux Home Products, Inc. All rights reserved. 12

Major Appliance Limited Warranty Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor, condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing) that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components other than those covered under the Sealed Refrigeration System 5-year warranty. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been removed, altered or cannot be readily determined. 2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada. 3. Rust on the interior or exterior of the unit. 4. Products purchased "as-is" are not covered by this warranty. 5. Food loss due to any refrigerator or freezer failures. 6. Products used in a commercial setting. 7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions. 8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance. 9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory. 10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts. 11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska. 12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc. 13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God. DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period Service should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below. This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice. USA Canada 1.800.944.9044 1.800.265.8352 Electrolux Major Appliances Electrolux Canada Corp. 10200 David Taylor Drive 5855 Terry Fox Way Charlotte, NC 28262 Mississauga, Ontario, Canada L5V 3E4 2009 Electrolux Home Products, Inc. All rights reserved. 13