Frigidaire FFEF3017LS LFEF3017LW LFEF3017LB wiring

Wednesday, March 29, 2017
Download

Electronic Oven SERVICE DATA SHEET Control (Rear View) Electric Ranges with ES 200/205/300 & 305 Electronic Oven Controls NOTICE - This service data sheet is intended for use by persons Oven Calibration having electrical and mechanical training and a level of Set the electronic oven control for normal baking at 350°F. Obtain an average oven knowledge of these subjects generally considered acceptable in temperature after a minimum of 5 cycles. Press STOP or CLEAR OFF to end bake the appliance repair trade. The manufacturer cannot be mode. responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet. Temperature Adjustment SAFE SERVICING PRACTICES 1. Set EOC to bake at 550°F. 2. Within 5 seconds of setting 550°F, press and hold the bake keypad for To avoid the possibility of personal injury and/or property damage, it is approximately 15 seconds until a single beep is heard (longer may cause F11 important that safe servicing practices be observed. The following are shorted keypad alarm). examples, but without limitation, of such practices. 3. Calibration offset should appear in the display. 1. Before servicing or moving an appliance remove power cord from 4. Use the slew keys to adjust the oven temperature up or down 35°F in 5°F electrical outlet, trip circuit breaker to OFF, or remove fuse. increments. Electronic Oven Control Fault Code Descriptions 2. Never interfere with the proper installation of any safety device. 5. Once the desired (-35° to 35°) offset has been applied, press STOP or CLEAR OFF. Fault Likely failure Suggested Corrective Action 3. GROUNDING: The standard color coding for safety ground wires is Code condition/cause GREEN or GREEN WITH YELLOW STRIPES. Ground leads are Note: Changing calibration affects normal Bake mode. The adjustments made will not not to be used as current carrying conductors. It is extremely F10 Runaway temperature. If Oven is cold: change the self-cleaning cycle temperature. Oven heats when no cook 1. If fault code is present with cold oven test oven temperature sensor probe circuit resistance. Use RTD scale found in the tech sheet. important that the service technician reestablish all safety grounds prior to completion of service. Failure to do so will cycle is programmed. 2. Replace probe or repair wiring connections if defective. 3. If temperature sensor probe circuit is good but fault code remains when oven is cold replace the EOC. create a potential safety hazard. If Oven is overheating: 4. Prior to returning the product to service, ensure that: Simmer Select PCB (some models) 1. If oven is severely overheating/heating when no cook cycle is programmed test oven temperature sensor probe circuit resistance using • All electric connections are correct and secure. the RED scale found in the service tech sheet. Also verify that the temperature sensor probe in properly installed in the oven cavity. • All electrical leads are properly dressed and secured away from 2. Disconnect power from the range, wait 30 seconds and reapply power. If oven continues to heat when the power is reapplied, replace sharp edges, high-temperature components, and moving parts. the EOC. NOTE: Severe overheating may require the entire oven to be replaced should damage be extensive. • All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels. F11 Shorted keypad or selector 1. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power. switch. 2. Check/reseat ribbon harness connections between touch panel and EOC. • All safety grounds (both internal and external) are correctly and 3. Test keyboard circuits. Replace touch panel if defective. securely reassembled. 4. If keyboard ciruits check good replace the EOC. F12 EOC Internal software error Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC. F13 or failure. E.O.C. Control Connections F30 Open oven sensor probe 1. (F30) Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance is correct replace the EOC. If circuit. resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector. P5 Connections F31 Shorted oven sensor probe 2. (F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted Sensor Probe circuit. harness between EOC & Probe connector. If resistance is correct replace the EOC. F90 Door lock motor or latch If lock motor runs: F91 circuit failure. 1. Test continuity of wiring between EOC and lock switch on lock motor assy. Repair if needed. F92 2. Advance motor until cam depresses the plunger on lock motor switch. Test continuity of switch contacts. If switch is open replace lock motor assemblyy. F93 3. If motor runs and switch contacts and wiring harness test good, replace the EOC. F94 If lock motor does not run: F95 1. Test continuity of lock motor windings. Replace lock motor assembly if windings are open. 2. Test lock motor operation by using a test cord to apply voltage. If motor does not operate replace lock motor assy. 3. If motor runs with test cord check continuity of wire harness to lock motor terminals. If harness is good replace the EOC. Resistance Temperature Detector Circuit Analysis Matrix RTD SCALE Temperature (°F) Resistance (ohms) 32 ± 1.9 1000 ± 4.0 IMPORTANT 75 ± 2.5 1091 ± 5.3 DO NOT REMOVE THIS BAG 250 ± 4.4 1453 ± 8.9 OR DESTROY THE CONTENTS 350 ± 5.4 1654 ± 10.8 WIRING DIAGRAMS AND SERVICE 450 ± 6.9 1852 ± 13.5 INFORMATION ENCLOSED 550 ± 8.2 2047 ± 15.8 REPLACE CONTENTS IN BAG 650 ± 9.6 2237 ± 18.5 900 ± 13.6 2697 ± 24.4 Please note that the Warmer Drawer feature is only for some models. p/n 316904426 (1001)

GENERAL TROUBLESHOOTING DIAGRAM GENERAL TROUBLESHOOTING SCHEMATIC