Ferrari F12berlinetta Owners Manual

Thursday, August 31, 2017
Download

Owner's manual

General remarks Caution and discipline are the basis of safe driving. Driving takes place in a naturally dangerous context where a This vehicle, which complies with EC homologation parameters, number of different risk factors interact: for this reason, it is uses advanced technology and is capable of achieving high important to drive bearing in mind that others, whether they are performance levels. pedestrians, motorcyclists or motorists, can make mistakes. Keeping It is equipped with sophisticated active and passive safety systems a safe distance allows emergency measures to be taken. Remember (described below). that national and international legislation requires that the driver These safety features and systems do not authorise the driver to of the vehicle must be capable of performing corrective and/or take risks other than those involved in normal driving since their emergency manoeuvres at all times. preventive and protective action is guaranteed only in certain Correct and careful use of a vehicle derives, above all, from respect conditions. Unless otherwise instructed specifically by Ferrari (see for one's own safety and that of others as well as from compliance the Safety chapter), the deactivation of any of the vehicle’s safety with road regulations. Only this respect will help you experience all systems is PROHIBITED. the emotions that driving this car can offer you. Certain safety systems (e.g. the airbags) have been tested to ensure The driver MUST NEVER allow passengers to increase the risks that they offer the highest possible levels of protection; they may associated with driving (e.g. by not using safety systems such as nonetheless be hazardous in the event of failure by the driver or the seat belts) by failing to observe the mandatory safety rules that passenger to observe the instructions given by Ferrari. All vehicle apply to both driver and passengers. occupants must be attentive at all times and take particular care The vehicle MUST NOT be modified or tampered with for when transporting passengers who are more subject to injury such any reason whatsoever since, by so doing, the manufacturer's as children, disabled and elderly persons. homologation and safety parameters will be modified. Safe driving is subject to the following conditions AT ALL TIMES: - the driver must be in perfect psycho-physical condition; - road regulations (Traffic Regulations - Vienna Convention on Road Traffic that ended on 8 November 1968) must be strictly observed; - common rules of caution must always be observed in relation to the quality/performance of the vehicle, driving conditions and contingent situations. 4 Introduction

The driver must pay the utmost attention to the signals of the It is important to bear in mind that on-board systems may be vehicle and, in particular, the warning lights on the dashboard and distracting when driving since they may take a driver's attention buzzers. Even when the warning lights do not indicate a situation away from the road for several seconds. of immediate danger, the driver must be cautious in relation to Aftermarket entertainment systems for the passenger (e.g. TV) possible consequences/degeneration of the failure and other must be installed where they cannot distract the driver while the information given. vehicle is in motion. While the vehicle is in motion, the attention During routine operations, such as refuelling, precautions should required to use on-board systems must never exceed the high level always been taken and it is important to check that flammable of attention required to drive safely in accordance with the Traffic liquid has not been spilled; these precautions must be observed Regulations. even if the operation is performed by others. Similarly, before Therefore, these systems may only be used (separately or in setting off make sure that the doors are closed by checking the combination with others) by the driver: warning lights and also manually. - in complete safety (stopping the vehicle before use if necessary). The driver must be fully acquainted with the vehicle and its Operations that are not involved with driving (e.g. changing controls in order to handle and drive it correctly. Command of the dashboard functions), must be performed in maximum safety vehicle can be acquired/improved by attending the driving courses when the vehicle is stationary; held by Ferrari which we strongly recommend. - putting road safety first; for example, under conditions of poor The use of terms from the motor sports world (such as F1, SPORT or limited visibility, looking at a display with active programmes and RACE) is merely indicative of the vehicle's competition-derived can be distracting even if you take your eye off the road only for a technology and does not endorse inappropriate behaviour on the split second; road which does not comply with Traffic Regulations. - ensuring, if the previous vehicle owner has installed systems on Most accidents are caused by distraction. The driver must use any the vehicle that are NOT APPROVED by Ferrari (car tuning), on-board information, communication and entertainment systems that they are fully compatible with the original vehicle equipment. responsibly, especially when the vehicle is in motion. Examples of information, communication and entertainment systems are the following: satellite navigation systems, traffic information systems (e.g. ITT), media players (e.g. iPod), telephones with Bluetooth connectivity, etc. (whether merely audio-based or with display). Introduction 5

If the vehicle owner has installed one or more new systems, either fixed or removable, on the vehicle, make sure that these: - have the necessary certification; - are fully compatible with the original vehicle equipment (i.e. they do not interfere with it); - are fitted by skilled staff. The Ferrari Technical Service Department and Ferrari Dealers and Authorised Service Centres can provide all the information needed to ensure that they are compatible. Strict priority criteria must be observed when driving a vehicle: you must not therefore take your attention off the road. In some countries, the use of information/entertainment/ systems is prohibited on vehicles when driving. The driver is responsible for use of these information/ entertainment systems with video screens if they are prohibited in the country where the vehicle will be driven. These considerations are not exhaustive, but only refer to some general issues that will be specifically dealt with in this Owner's Manual. 6 Introduction

Introduction Warranty Booklet The aim of this Owner’s Manual is to help you get the best Each new vehicle comes with a “Warranty Booklet”. value from your vehicle and to provide information on routine This contains the vehicle’s warranty validity conditions. maintenance: we advise you to read it carefully before setting out. This warranty does not affect the buyer's statutory rights as a The Owner’s Manual should be considered an integral part of the consumer, which derive from binding legal norms in his or her vehicle and must therefore always be kept on board. favour, in the various states or countries, or from European Union Using the product in a way that does NOT comply with the regulations, towards the Dealer. Owner's Manual not only exonerates Ferrari of any responsibility The Warranty Booklet also contains the routine maintenance but also puts the person at great risk. indicated in the “Maintenance Schedule”. Updating The high quality level of the vehicle is subject to constant technological improvements. Therefore, there may be differences between this manual and your vehicle. The Ferrari Sales and Service Network will provide you with all the information on any updates. All specifications and illustrations contained in this manual are accurate as of the date of printing. Spare parts When replacing parts or topping up with lubricants and fluids, we recommend that you use original spare parts and lubricants and fluids recommended by Ferrari. Introduction 7

Service Consulting the manual The information in this manual is necessary for the use and proper To facilitate reading the manual, the topics have been divided into care of the vehicle. In addition, Customers will get maximum sections and chapters. satisfaction and results from the vehicle if they carefully follow the instructions contained in it. We recommend that you have all the checks and services performed 1. General at Ferrari Authorised Workshops since they have highly skilled Provides general information about your vehicle. staff and the necessary equipment. 2. Safety In the case of erroneous maintenance or repairs (that do not conform to the technical repair standards and procedures adopted Describes the main safety systems in the vehicle. by Ferrari), undertaken by independent repair centres, particularly 3. About your Vehicle if concerning safety systems or safety, Ferrari may decide to Provides all necessary information for use of the vehicle. not carry out further repairs on the vehicle, unless the vehicle is restored so that it conforms to original parameters. 4. Advice for Emergency Situations The Customer Care Service, available at the numbers indicated Provides useful advice for solving problems that may occur. in the “Reference Guide” booklet enclosed with the vehicle documents, can provide information on the location of Ferrari 5. Care of the vehicle Dealers and Authorised Service Centres. Provides advice for cleaning, care and routine maintenance of The Ferrari Technical Service Department is at your complete your vehicle. disposal for any information and advice. If you have any doubts about the information provided in this manual or how to use or 6. Glossary operate the vehicle, please contact the Ferrari Service Network. Explains the main technical concepts. 7. Table of Contents Allows you to quickly identify and locate the information required. 8 Introduction

Within the various sections, special attention must be paid to Abbreviations/Acronyms the parts marked as follows: Some descriptions and terms with particular meanings are found in this manual in an abbreviated form: Warning A.C. Air conditioning Extreme caution required: failure to comply with the ABS Anti-lock Braking System instructions could constitute a serious risk to personal safety and vehicle protection! ASR Anti-skid Regulation during acceleration DCT Dual Clutch Transmission EBD Electronic Brake-force Distribution Important note ECU Electronic Control Unit Important note: a note containing instructions or information. ESC Electronic Stability Control F1-Trac Traction control derived from the technologies used in the racing sector. Environment Warning for environmental protection: useful advice for protection of the environment. Introduction 9

Environmental protection Driving style - Do not accelerate during the starting procedure - Do not warm up the engine when the vehicle is stationary Environment - Drive carefully and keep a safety distance that corresponds to the The following chapter contains useful advice for environmental driving speed protection. - Avoid sudden and frequent acceleration or braking - Turn off the engine if the vehicle is kept stationary for long Ferrari has designed and constructed a vehicle using technologies, periods of time materials and devices capable of reducing the harmful impact on - Shift gears using only 2/3 of the speed permitted for each gear the environment to a minimum. - Use the air conditioning in moderation If you use your vehicle with respect for the environment, you too will contribute to environmental protection. - A driving style like that described above protects the vehicle from premature wear and tear, makes driving safer and does not Fuel consumption as well as engine, gearbox, brakes and tyres wear subject the vehicle to undue fatigue. mainly depend on two factors: - use of the vehicle Important note - driving style. Both factors are influenced by the driver. The vehicle is equipped with exhaust gas control and monitoring systems which must always be kept in perfect working order and controlled regularly. Use of the vehicle - Avoid using the vehicle for short trips - Check that the tyre pressure is correct - Check the fuel consumption - Proper periodic maintenance will contribute to preserving your vehicle in full working order and to protecting the environment. We therefore advise you to respect the service due dates indicated in the “Maintenance Schedule”. 10 Introduction

End-of-life vehicle collection service Bear in mind that specific regulations govern the disposal of vehicle parts including batteries, tyres, used oil, etc. (applies to EU countries only) Please contact the Ferrari Service Network for more For many years, Ferrari has been globally committed to respecting information. and protecting the environment by constantly improving its manufacturing processes and developing increasingly eco- compatible products. Regulations for the treatment of end-of-life vehicles, implemented in response to the terms of EU Directive 2000/53, require that producers (manufacturers and official importers) collect all the vehicles introduced on the market by the producers themselves at the end of their life cycle, and ensure that these vehicles are processed in an environmentally compatible manner. Therefore, to dispose of your end-of-life vehicle at no additional cost (with the exception of a de-registration fee and any transport costs), contact your nearest Ferrari dealer who is responsible for taking the vehicle to one of the authorised collection and disposal centres which have all been selected to guarantee a service that meets quality standards for the collection, treatment and recovery of recyclable materials without harming the environment. For further information, visit www.ferrari.com. To dispose of a Ferrari end-of-life vehicle, the vehicle must be: - complete, containing the essential components including engine, transmission, bodywork, ECUs and catalytic converter; - free from additional waste. Ferrari is committed to offering its clients a geographically extensive and, as a result, better service, and thanks you for your cooperation in this environmental challenge. Introduction 11

Vehicle keys............................................................ 14 Alarm system.......................................................... 15 Duplicating the keys............................................... 16 Replacing remote control batteries.......................... 17 Electronic alarm..................................................... 17 Identification and homologation plates and labels... 20 Dimensions and weights......................................... 27 Main engine specifications...................................... 28 Consumption and emissions................................... 28 Performance........................................................... 28 Wheel rims and tyres.............................................. 29 Refilling.................................................................. 35

1 GENERAL

Vehicle keys Key codes The vehicle is delivered with two identical keys that can be used A CODE CARD is supplied together with the keys, indicating the for: following: - central door locking; - the electronic code; - starting the vehicle; - the mechanical code for the keys, to be given to the Ferrari Service Network if you request duplicates of the keys. - activating/deactivating the alarm system; - opening the luggage compartment lid. Warning Important note The code numbers on the CODE CARD must always be kept in a safe and protected place, not accessible to others. If the keys are lost or stolen, you can request a duplicate from the Ferrari Service Network (see the “Duplicating the keys” section on page 16). Important note In the event of a change of ownership, it is essential that the new vehicle owner is provided with all the keys and with the CODE CARD. 14 General

Alarm system When starting the engine, press the ENGINE START button on the 1 steering wheel: The Ferrari CODE system 1) If the code is recognised, the CODE warning light A on the instrument panel turns off when the check procedure has been The vehicle is equipped with an electronic immobiliser system completed, whereas the EOBD warning light B turns off when (Ferrari CODE) which is automatically activated when the ignition the engine is started once the ECU has completed its diagnostic key is removed. cycle; in these conditions, the protection system has recognised The keys are equipped with an electronic device which transmits the key code and deactivated the immobiliser. a coded signal to the Ferrari CODE ECU. Once this ECU has recognised the signal, it allows starting the engine. 2) If the CODE warning light A stays on, it means that the code has not been recognised. If this occurs, it is advisable to turn the key back to position 0 and then back to II; if the immobiliser Operation device remains active, try with the other key provided. Each time the ignition key is removed (see page 77), the protection system activates the engine immobiliser. Important note If you still cannot restart the engine, contact the Ferrari Service Network. B A General 15

While driving, with the ignition key in position II: 1) If the CODE warning light A turns on, it means that the system Important note is performing a self-diagnostic cycle. At the first opportunity, Each key provided has its own specific code, which must be you can stop and test the system: switch off the engine by stored in the memory of the system control unit. turning the ignition key to position 0, then turn the key back to position II. The CODE warning light A will turn on and should go off within one second. If the warning light stays on, repeat Important note the procedure described previously leaving the key at 0 for more than 30 seconds. Contact the Ferrari Service Network immediately to have all the keys stored in the system memory. Important note If the problem persists, please contact the Ferrari Service Duplicating the keys Network. If you request additional keys, provided that the conditions to satisfy your request are met, remember that the codes must be 2) If the CODE warning light A flashes, it means that the vehicle is stored (up to a maximum of 7 keys) on all the keys. not protected by the immobiliser. Contact the Ferrari Service Network directly and bring the following with you: - all the keys in your possession; - the CODE CARD for the Ferrari CODE system; - a personal identity document; - the documents proving ownership of the vehicle; - a report of loss of keys made to the relevant authorities. The codes for the keys that are not available when the new B memorisation procedure is performed will be deleted from the memory to prevent any lost or stolen keys being used to start the vehicle. A 16 General

Replacing remote control batteries Electronic alarm If you press one of the three buttons on the key and this does not activate the corresponding function, check that the alarm system The electronic alarm system performs the following functions: - remote control for central door locking/unlocking; 1 functions are operating correctly by using the other remote control before replacing the two remote control batteries. - perimeter surveillance, detecting if doors and lids are open; Replace the remote control batteries as follows: - motion surveillance, detecting intrusion in the passenger compartment; - open the key cover C using a small screwdriver at the position indicated by the arrow; - vehicle movement surveillance (anti-lift). - remove the two batteries E, pushing in the direction indicated by the arrow to release them from the retainer cover D; Activation - fit two new batteries of the same type, observing the indicated To turn on the alarm system, press button F on the ignition key: polarity; - the turn indicators flash once; - close the key cover C. - the system “beeps”; - the red LED on the dashboard flashes; Important note - the central door locking system is activated and the doors are Do not use sharp tools to remove the cover and be careful to locked. avoid damaging the remote control. The system activates after approximately 25 seconds. E D F C G General 17

When the electronic alarm is activated, the user may request Pressing button G twice unlocks the doors and also turns on the opening of the luggage compartment lid; in this case, the motion low beams for 30 seconds. and anti-lift sensors are temporarily deactivated. If the luggage The alarm system is off and you can now get into the vehicle and compartment is then closed, the sensors will be reactivated. start the engine. If the turn indicators and the red LED on the dashboard flash To enter the vehicle if the remote control battery is flat, insert the 9 times when you activate the alarm system, it means that one of key into one of the two door locks and turn it to release the lock; the doors or the front/rear lid is open or not closed properly and is the alarm siren will start to sound. therefore not protected by the perimeter surveillance. If this is the Start the vehicle following the standard procedures: The alarm case, check that the doors and front/rear lids are closed properly siren will deactivate. and close any door or lid that is open without deactivating the alarm system: the turn indicators will flash once to indicate that the door and front/rear lids are now closed properly and protected by Deactivating the anti-lift volumetric alarm the perimeter surveillance. Press button H on the roof panel to deactivate the anti-lift volumetric alarm system. When this function is deactivated, the Warning indicator light on the button will flash for about 3 seconds and will then turn off. If the turn indicators and the LED on the dashboard flash 9 times when the alarm system is activated with doors, rear and front lids properly closed, it means that the self-diagnostic feature has detected a malfunction in the system. Contact the Ferrari Service Network to have the system checked. Deactivation To deactivate the alarm system, press button G on the ignition key: H - the turn indicators flash twice; - the system beeps twice; - the red LED on the dashboard goes off; - the dome lights come on; - the central door locking system is deactivated and the doors are unlocked. 18 General

Alarm memory Homologation If, when the vehicle is started, the CODE symbol (see page 107) appears on the left TFT display of the instrument panel for 10 seconds after the system diagnosis cycle, together with the The electronic alarm system complies with EU regulations on electromagnetic compatibility and is marked in compliance. 1 The homologation number is referred to with the following message “Break-in attempted”, this means there has been an characters. attempt to break into the car, causing the alarm to activate. For those markets that require the transmitter and/or receiver In this case, the system will indicate the reason for the alarm marking, the homologation number is found on the component. activation according to the following priority: - LED off twice: anti-lift sensor alarm Satellite alarm system (optional) - LED off three times: door alarm In some markets, the vehicle can be equipped, on request, with - LED off four times: luggage compartment lid alarm a satellite alarm system. If the vehicle is equipped with a satellite - LED off five times: ignition key alarm. alarm system, please refer to the “Nav Trak Satellite Alarm System The alarm system memory is reset by turning the ignition key. Quick Reference” booklet enclosed with the vehicle documents, for further information. General 19

Identification and homologation plates and labels H I G F E D C B A L M N O P Q U R T S 20 General

1 Ref. Label/plate Position A Low-beam homologation Engine compartment lid B ECE homologation Engine compartment lid C Radiator with antifreeze RH engine compartment cosmetic shield D Checking the engine oil level RH engine compartment cosmetic shield E Engine and gearbox oil label RH engine compartment cosmetic shield F Installation of rearward facing child seat not allowed Passenger-side dashboard side panel G Passenger airbag warning (2) Passenger-side sun visor H Vehicle identification Rear passenger-side door jamb I Unleaded fuel Fuel filler flap L Maximum permitted speed with winter tyres Rear driver side door jamb M TPMS present warning Driver-side door N Tyre pressure and type Driver-side door O Gearbox type and number Gearbox housing P Chassis number Windscreen Q Original paintwork Engine compartment lid R Stop&Start system warning (only with HELE) LH engine compartment cosmetic shield S Danger - High voltage LH engine compartment cosmetic shield T Engine type and number Crankcase U Assembly number Engine compartment General 21

A  Low-beam homologation C  Radiator with antifreeze B  ECE homologation D  Checking engine oil level 22 General

E  Engine and gearbox oil label G  Passenger side airbag warning (2) 1 F  Installation of rearward facing child seats not allowed H  Vehicle identification General 23

I  Unleaded fuel M  TPMS present warning L  Maximum permitted speed with winter tyres N  Tyre pressure and type 24 General

O  Gearbox type and number Q  Original paintwork 1 P  Chassis number R  Stop&Start system warning (with HELE only) General 25

S  Danger - High voltage U  Assembly number T  Engine type and number 26 General

Dimensions and weights Wheelbase 2718 mm (107 in.) 1 Max. length 4632 mm (172 in.) 1276 Max. width 2080 mm (82 in.) Max. height 1276 mm (50 in.) Front track 1659 mm (65 in.) Rear track 1600 mm (63 in.) Front overhang 963 mm (38 in.) 1659 1600 Rear overhang 951 mm (37 in.) Kerb weight 1630 kg (3593.5 lbs)* 2080 * considering the most favourable Optional combination 2718 4632 General 27

Main engine specifications Transmission ratios Type F 140 FC Gearbox Differential/bevel Number of cylinders 12 ratios gear pair ratio Cylinder sequence V 65° 1 = 3.077 Cylinder bore 94 mm (3.7 in.) 2 = 2.185 Piston stroke 75.2 mm (3 in.) 3 = 1.626 4.375 Total displacement 6262 cm³ 4 = 1.286 (382.1 cu. in.) 5 = 1.028 Compression ratio 13.5:1 6 = 0.839 Maximum RPM 8700 RPM 7 = 0.693 (with limiting device) R = 2.791 Maximum power 541 kW (735 hp) * Performance Corresponding RPM 8250 RPM Maximum torque 690 Nm 0 - 100 km/h 0 - 200 km/h Maximum speed Corresponding RPM 6000 RPM 3.1 s 8.5 s > 340 km/h (211.3 mph) Consumption and CO2 emissions Electrical system Supply voltage Alternator Standard With version HELE system 12V Nippondenso 165 A SC3 l/100 km g/km l/100 km g/km Battery Starter motor City cycle 24.9 583 21.9 513 Fiamm 12V - 95 A/h Nippondenso L5 AGM 850 A EN Motorway 11.3 265 10.9 256 Combined cycle 16.3 380 15.0 350 *: value obtained with 98 RON unleaded fuel 28 General

Wheel rims and tyres Wheel rims 1 Front Rear Space saver spare wheel 9.5” J x 20” ET 48.4 11.5” J x 20” ET 71.6 4.5” J x 20” Explanation of wheel rim codes Example: 9.5” J x 20” ET 48.4 9.5” = Rim width in inches J = Shape of rim edge (side projection where tyre bead rests) 20” = Rim diameter in inches ET 48.4 = Offset (distance, in mm, between the centreline of the rim and inner rim surface) General 29

Ferrari-approved tyres Inflation pressure * * * (cold) Michelin Pilot Super Sport Front 255/35 ZR 20 2.40 bar (34.8 psi) E B 71 dB Rear 315/35 ZR 20 2.20 bar (31.9 psi) E B 75 dB Pirelli PZero Front 255/35 ZR 20 2.10 bar (30.5 psi) E B 73 dB Rear 315/35 ZR 20 2.00 bar (29 psi) F A 74 dB Optional tyres Inflation pressure (cold) Front Rear Front Rear Vredestein space saver 145/60 R 20 4.20 bar (60.9 psi) spare wheel Winter tyres Inflation pressure * * * (cold) Pirelli Winter Sottozero Front 255/35 R 20 M+S 2.40 bar (34.8 psi) E C 73 dB Rear 305/35 R 20 M+S 2.20 bar (31.9 psi) E C 73 dB *: Regulation no. 1222/2009/EC (see page 33) 30 General

Explanation of codes and wording on tyre side walls 105 = Load index: numerical code associated with the maximum 1 1) Tyre size and characteristics load permissible on the tyre at a given pressure, at the speed corresponding to the relative index. The maximum load permissible Example: 245/35 ZR 20 (105Y) is indicated in kg and pounds in the wording (3). 245 = Nominal width (distance in mm from side to side) Y = Speed index: 35 = Height/width ratio as a percentage This indicates the maximum speed at which the tyre can withstand ZR = Radial tyre that can withstand speeds above 240 km/h the load indicated in the load index. (149 mph). Combined with the specific load and speed code (in Speed indexes (ECE-UN 30) are shown in the table below: brackets), this indicates a tyre that can withstand speeds above 300 km/h (186 mph). Speed Index Maximum speed (km/h) 20 = Rim diameter in inches M 130 N 140 P 150 6 Q 160 R 170 D PLIES: T REA 1 PO TE EL + 1 P LY E + 2 S O LY ST W A L L P LY 4 AM ER SIDE PO I LY E D E ST ER 5 S 180 4 T 190 I) ) PS BS Y L L U 200 N (5 39 O 3 0 KG D E S 0 KP (2 O A . C .S 5 0 U PR E D 92 34 D AN SS LO A A AD H 210 CAN MAX MAX V 240 7 W 270 Y 300 8 ZR (... Y) > 300 The speed index Y, shown in brackets and associated with the 2 abbreviation ZR, indicates a tyre that can withstand speeds above 1 300 km/h (186 mph). General 31

2) EXTRA LOAD: tyre with a high load capacity 3) Maximum load permissible, indicated in kg and pounds, and maximum inflation pressure permissible, indicated in kPa and psi. 4) TUBELESS: the tyre has no air chamber 5) RADIAL: radial tyre 6) Details of materials used to construct the tread and tyre side wall. 7) DOT XX YY ZZ NNNN DOT (Department Of Transportation) specifications: marking relative to US regulations, with information on the manufacturer, production site, tyre type and size. The last four digits, in a box, indicate the date of manufacture: 1011 means that the tyre was manufactured in the 10th week of 2011. Warning Ensure that tyres are not kept in stock for more than 4 years from the date of manufacture. The maximum limit for keeping tyres in stock is 4 years provided they are kept away from sunlight, bad weather and damp and where there is a low oxygen content. 8) Uniform Tire Quality Grading: standard, defined by the US Department of Transportation, that classifies tyre performance in terms of treadwear, traction and temperature resistance. For further information on tyres, see page 243. 32 General

Regulation no. 1222/2009/EC (applies to EU countries only) External rolling noise Regulation no. 1222/2009/EC states that all tyres sold in EU countries produced after 1 July 2012 must bear a label (as shown in the bottom right) containing important information on The bottom of the label indicates the external noise level of the tyre. The external noise level is measured in decibels (dB) and is divided into 3 categories based on the new, stricter European levels 1 performance. of external tyre noise which will be introduced by 2016. The aim of the regulation is to provide consumers with more 1 black sound wave: 3 dB below future European limit information on safety (wet grip) and environmental (rolling 2 black sound waves: complies with future European limit resistance and external rolling noise) issues in order to promote the 3 black sound waves: complies with current European limit. use of safer, quieter and more efficient tyres. The label provides the following information: Fuel consumption The fuel consumption of a vehicle is influenced by the tyre rolling resistance. There is a scale with 7 levels, from A to G, on the left of the label where “A” indicates the best tyre class for reducing fuel consumption with lower rolling resistance. Wet grip On the right of the label, there is a scale for tyre performance when braking on wet roads. Measurements are taken under test conditions defined in the European Regulation. The scale has 7 levels, from A to G, where “A” indicates the maximum wet grip. 72 dB General 33

Run Flat tyres (optional) The vehicle can be fitted with “Run flat” tyres, if required. This type Warning of tyre has a reinforced side A which allows the vehicle to continue If you are going to use standard tyres on a vehicle that was travelling at moderate speed (80 km/h - 50 mph), even after a originally equipped with “Run Flat” tyres, you must contact puncture, for a specific distance (100 km - 62 mi). the Ferrari Service Network to have the dashboard When the instrument panel receives the “tyre puncture” reprogrammed and prevent warning messages from being information from the tyre pressure monitoring ECU, calculates the displayed on the left TFT display. residual tyre life, and displays a warning in the dedicated area of the left TFT display after 50 km (31 mi). After 100 Km, a message warning the driver to stop the vehicle will Environment be displayed (for further information, see the “Tyre pressure and Maintaining correct tyre pressure helps to improve tyre rolling temperature monitoring system” paragraph on page 65). and reduce fuel consumption. Warning Observing the recommended wheel alignment values is essential in order to obtain the best performance and the longest life of these tyres. A 34 General

Refilling Parts to be refilled Quantity Fill with: Page 1 Engine Total system capacity 15.5 l SHELL HELIX ULTRA Racing SAE 10W-60 238 Oil level between Min. and Max. 1.5 l Oil consumption 1.0 - 2.0 l/1,000 km Gearbox and differential 3.5 l SHELL SPIRAX S5 ATE 75W-90 239 Clutch system and hydraulic controls 7.75 l SHELL DCT-F3 Braking system 1.2 l SHELL BRAKE AND CLUTCH DOT4 Ultra 241 Cooling circuit 24 l GLYCOSHELL LONGLIFE at 50% 240 KEMETYL CARIX Premium G30 Longlife at 50% Hydraulic power steering system 1.25 l PENTOSIN CHF 11S 240 Fuel tank 90 l Unleaded petrol (at least 95 R.O.N.) 83 Air conditioning and heating system Compressor 165 cc PAG ISO 46 Coolant 560 ± 30 g HFO-1234yf Windscreen washer/headlight washer fluid tank 6l Mixture of water and glass cleaner 242 General 35

Instructions for vehicle refuelling Warning Warning The use of unleaded petrol with a R.O.N. below 95 can cause malfunctioning and is not recommended. Only fill the vehicle with unleaded petrol. Using unleaded petrol is fundamentally important to ensure Important note that the catalytic converters of the vehicle's exhaust system work properly. This vehicle is suitable for use with unleaded fuel with a maximum of 10% ethanol (E10) Warning Never put leaded petrol in the fuel tank, not even in Warning emergencies: fuel deposits could irreparably damage the The use of fuels with 10% to 25% ethanol can lead to catalytic converters. malfunctioning. The use of fuels with over 25% ethanol can cause permanent For optimal engine performance and efficiency, Ferrari strongly damage to the engine fuel system. recommends using unleaded petrol with an octane rating (R.O.N.) of 98. See page 83 for further information. As unleaded petrol with a 98 R.O.N. is not always available, the engine is any case suitable for using unleaded petrol with an octane rating not below 95 R.O.N. In this case, the engine control system will appropriately adjust calibrations, allowing the vehicle to function correctly, although performance is decreased. 36 General

Passive safety.......................................................... 42 Active safety........................................................... 43 Seat belts............................................................... 44 How to fasten seat belts......................................... 46 Pretensioners.......................................................... 48 Auxiliary Occupant Protection Systems.................... 50 Driver and passenger airbags................................... 51 Side airbags............................................................ 56 Fuel inertia switch................................................... 59 ABS and EBD......................................................... 60 Electronic Stability Control..................................... 62 Electric parking brake............................................. 64 TPMS..................................................................... 65

2 SAFETY

Ferrari has designed and built a high performance vehicle. Emissions In order to take advantage of the safety systems described below, it is essential to comply with the indicated regulations. Warning • The exhaust gas generated by the running engine is hazardous, Special recommendations especially when in closed or poorly ventilated spaces. As well This vehicle has been built to comply with homologation as consuming oxygen, the engine discharges carbon dioxide, regulations that also concern safety and environmental protection. carbon oxide and other toxic gases. These high technological standards must always be accompanied by • Fuel is highly inflammable and emits vapours which may be careful and cautious driving. noxious if inhaled. Particular attention must be paid to: Do not use naked flames or create sparks near the open fuel • Overheated components. High temperatures develop in the tank or in any other condition where fuel comes into contact engine compartment near the exhaust system. Do not park the with air. vehicle on paper, grass, dry leaves or other flammable materials. They could catch fire if they come into contact with hot parts of the exhaust system. Do not fit other heat shields or remove those Lubricants fitted on the exhaust system. Do not let flammable substances come into contact with the exhaust system. Warning • Moving parts of the vehicle such as belts, fans, etc. They must always be adequately protected. Do not remove the guards or The oils used may also be inflammable: take the same operate on the moving parts without taking due precautions. precautions as those adopted for fuel. • Installations under pressure such as braking system, air conditioning system, cooling system and lubrication system may create pressures inside them. Do not perform any operation which Flammable fluids may cause gas or liquids to spill out with the risk of injury to persons and damage to things. Warning The fluid in the battery is poisonous and corrosive. Do not let it spill out and come into contact with the skin, eyes or objects. Do not use naked flames or create sparks near the battery. 40 Safety

Warning Warning Seat belts must be worn at all times and must be properly Each seat belt has been designed to protect only one occupant. fastened and adjusted! If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. 2 Do not sit babies, small children or other persons on your lap. Warning If there is a collision, the weight of an adult may cause the For an effective restraining action, the seat belt must be fastened child to be crushed by the seat belt causing severe or even fatal correctly with the seat backrest in the upright position. injuries. The seat belt is fastened correctly when the upper part of the belt crosses the centre of the shoulder (not the neck) and the abdominal section is fitted over the hips (not the abdomen). Make sure that the belt is not twisted and that it passes closely over your body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Avoid wearing bulky clothing that may interfere with the proper operation of the seat belts. Safety 41

Passive safety • occupant protection system ECU • ECU auxiliary sensors The passive safety system has been designed to reduce the risk and severity of injury if an accident occurs. • instrument panel warning light (see page 112) The vehicle is equipped with the following seat belts: • inertia switch. • 3-point driver seat belt with pretensioner and load limiter (see page 44) Warning • 3-point passenger seat belt with pretensioner and load limiter The protective action of the airbags is always integrated with (see page 44) the seat belts and the pretensioners. The compulsory use of the seat belt is provided by the national regulations (in Italy, for Warning example, by the Codice della Strada, i.e. Traffic Regulations). Auxiliary safety systems are not a substitute for seat belts. All occupants must always wear a seat belt. Correct use of the seat belts combined with use of the auxiliary safety systems Deformable body provides optimal protection to the occupants in various types of The deformable body absorbs shock and distributes it over the collisions. entire structure of the vehicle allowing progressive deceleration. The passenger compartment structure, on the other hand, has been The vehicle also has the following auxiliary occupant protection designed to provide maximum resistance without undergoing system components (see also page 50 “Auxiliary occupant deformation in order to guarantee a protective survival cell for the protection systems”): occupants. • driver side front airbag (see page 52 for functioning logic) • passenger side front airbag (see page 52 for functioning logic) • driver side lateral airbag (head bag) (see page 56 for functioning logic) • passenger side lateral airbag (head bag) (see page 56 for functioning logic) • seats (see page 178) • deformable body 42 Safety

Active safety The aim of the active safety system is to reduce the risk of accidents and injury severity. The vehicle has been designed to provide a high level of safety for whoever uses it. The following systems are specific active safety components: • braking system 2 • air conditioning and heating system • external lights • buzzer and warning light (flashing). The braking system includes the mechanical brake system and the electronic stability and traction control system (ABS and EBD): this is designed to prevent the wheels from locking and to provide good handling and stability. In some situations, fast acceleration is important to get out of dangerous situations. However, always use the accelerator with extreme caution. During acceleration of the driving wheels, the anti- skid system may help you in certain dangerous situations. The air conditioning and heating system in the passenger compartment can add to driving comfort and keep you alert so that you can react quickly when necessary. It is very important to be able to see the road clearly and be seen and external lights must be turned on when the conditions so require. Safety 43

Seat belts Warning Statistics show that when used correctly, seat belts reduce the risk of injury in various types of crashes including the risk of ejection For an effective restraining action, the seat belt must be fastened from the vehicle and impact with the interior of the vehicle. correctly with the seat backrest in the upright position. If unfastened, the seat belts do not provide any type of protection. The seat belt is fastened correctly when the upper part of the Before every trip, always make sure that all occupants are wearing belt crosses the centre of the shoulder (not the neck) and the their seat belts. abdominal section is fitted over the hips (not the abdomen). Make sure that the belt is not twisted and that it passes closely Warning over your body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Seat belts must be worn at all times and must be properly Avoid wearing bulky clothing that may interfere with the proper fastened and adjusted! operation of the seat belts. Correct use of the seat belts can reduce the risk of serious injury in the event of an accident or if the vehicle overturns. The seat belts have a lap-shoulder belt with an automatic emergency-locking retractor and are fitted with a pyrotechnic- powered pretensioner and an automatic system that reduces the force applied to the occupant. 44 Safety

Warning Warning Do not let the seat belts come into contact with cutting edges. Periodically check the condition of the seat belts. If the belt They may get damaged and may consequently break in the shows signs of wear, it must be checked by a qualified person event of a collision. and replaced if necessary. Contact the Ferrari Service Network immediately. Warning 2 Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not sit babies, small children or other persons on your lap. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning Do not attach or pin anything onto the seat belts: they may get damaged and may consequently break in the event of a collision. Warning If a seat belt has come into contact with cutting edges or was somehow perforated, we recommend that you have it replaced by the Ferrari Service Network. Safety 45

How to fasten seat belts Once you have adjusted the seat correctly (see page 178): • Grip the latch plate A, slightly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it Warning out, let it wind back a little and pull it out again without jerking For an effective restraining action, the seat belt must be fastened it). correctly with the seat backrest in the upright position. • Make sure that it has clicked into the locked position: hold the The seat belt is fastened correctly when the upper part of the belt and pull it to check that the latch plate has been inserted belt crosses the centre of the shoulder (not the neck) and the correctly. abdominal section is fitted over the hips (not the abdomen). • Position the seat belt correctly. Make sure that the belt is not twisted and that it passes closely If the driver’s seat belt is not fastened, when you turn the ignition over your body; if not, in the event of a head-on collision, it may key to position II, the warning light D on the instrument panel move and cause injury to the abdomen. lights up and remains lit until the seat belt is fastened. Avoid wearing bulky clothing that may interfere with the proper 55 seconds after a speed of 10 km/h (6 mph) is exceeded, a buzzer operation of the seat belts. sounds warning the driver that the seat belt is not fastened. When a speed of 20 km/h (12 mph) is exceeded, the buzzer activates immediately and stops after 90 seconds. This acoustic signal is emitted only once, even if the vehicle speed goes above and below the above mentioned limits. It is repeated (when the vehicle speed is in the indicated ranges) only if the seat belt is fastened and unfastened again or, in any case, every time the engine is turned off and then on. A D B 46 Safety

Pregnant women Warning The best protection for pregnant women and their unborn babies Each seat belt has been designed to protect only one occupant. is to wear 3-point seat belts correctly. This significantly reduces If more than one person uses the same seat belt, the risk of the risk of injury to the baby. Consequently, pregnant women injury in the event of an accident is increased. should always wear seat belts unless they have a specific medical exemption. 2 The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. The upper part of the diagonal section of the seat belt must lie snug Do not sit babies, small children or other persons on your lap. on the front of the shoulder, pass between the breasts down to the abdomen. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal The horizontal strap must sit snug as low as possible under the injuries. abdomen. Unfastening the seat belts • Push the release button E. • Guide the latch plate A back to its rest position. A E Safety 47

Pretensioners When a pretensioner is activated, a small amount of smoke is released. This smoke is not harmful. The seat belts are fitted with pyrotechnic-powered pretensioners. The pretensioner is activated by the airbag ECU when there is a sufficiently severe head-on collision (impact direction between 11 Warning and 1 o'clock p.m.) or a sufficiently severe side collision. The belt Activation of the pretensioners only depends on the status of the will rewind a few centimetres just before the restraining action seat belts and is not affected by the occupants' presence. begins, thereby improving the fitting across the occupant's body. If the seat belt is not fastened, the pretensioner will not activate, Activation of a pretensioner is signalled by the illumination of the even if the seat is occupied. warning light A on the instrument panel. The seat belts are fitted with a load limiting device. The load Warning limiting device is located in the belt retractor and allows controlled Pretensioners that have been activated will no longer function release of the belt during a collision thereby limiting the impact and may not be repaired under any circumstances. Contact the that the belt has on the occupant's body. Ferrari Service Network for replacement. A 48 Safety

Seat belt and pretensioner care Important note • Following a serious collision, replace the seat belts that were worn at the time even if they do not appear to be damaged. All work on any part of this safety system must be performed by • Periodically check that the screws on the anchor points are tight the Ferrari Service Network. and that the seat belt is in perfect condition and slides smoothly. • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. Warning Removing or making modifications of any kind to the seat belts, 2 • To clean the seat belt, wash it by hand with mild soap and water and let it dry. Do not use strong detergents, bleach or aggressive belt retractors and pretensioners is not allowed. solvents, as they can weaken the fibres. Make sure the retractors Maintenance work involving strong impacts, vibrations or do not get wet: proper functioning is only ensured if they are kept heating of the pretensioner area may activate them; vibrations dry. caused by road bumps will not have this effect. • The pretensioner requires no maintenance or lubrication. • If immersed in water or mud, the pretensioner must necessarily be replaced. • Pretensioners must be replaced at regular intervals as indicated in the “Warranty Booklet”. Safety 49

Auxiliary Occupant Protection Systems The driver and passenger side front airbags are designed to augment the protection provided by the seat belts in the event of a head-on collision (see page 51). Warning The driver's head protection side airbag and passenger head Auxiliary Occupant Protection Systems are not a substitute for protection side airbag have been designed to increase the level of seat belts but increase their efficiency. Correct use of the seat protection given by the seat belts in the event of a side collision belts, with the supplementary action of the Auxiliary Occupant and are placed between the occupant’s head and external structures Protection Systems, offers maximum protection in the event of a which could penetrate the passenger compartment and cause injury head-on collision or vehicle roll-over. (see page 56). Auxiliary Occupant Protection System components The Auxiliary Occupant Protection System components are: • Seat with built-in headrest • Dual-stage front driver's airbag • Dual-stage front passenger airbag • Driver's head protection side airbag (head bag) • Passenger head protection side airbag (head bag) • Driver's seat belt (3-point with pretensioner and an automatic system that reduces the force applied to the occupant) • Passenger seat belt (3-point with pretensioner and an automatic system that reduces the force applied to the occupant) • Electronic Control Unit (ECU) • Additional sensors • Instrument panel warning light • Deformable body. 50 Safety

Warning Warning The warning light A comes on when the ignition key is turned The front airbags have been designed not to inflate if a minor to position II. If no malfunctions are detected, it goes out after collision occurs. The seat belts have been designed to reduce 4 seconds. If the warning light does not come on, if it remains the risk of injury if a minor collision occurs. on or if it comes on while driving, contact the Ferrari Service Network immediately. Warning 2 Driver and passenger airbags The driver and the passenger must maintain a distance of at least 25 cm (10 in.) from the steering wheel and the dashboard. Warning Always drive with your hands on the rim of the steering wheel so that in the event of activation, the airbag can deploy without The front airbags do not provide protection in the event of obstruction. side-on collisions, some head-on/angular collisions, roll-overs Driving with your hands on the steering wheel spokes or on the or subsequent collisions (if there is a second collision once the airbag cover increases the risk of injury for your wrists and arms airbags have been deployed in an earlier collision). The seat if the airbags are deployed. belts have been designed to reduce the risk of injury in the event of a roll-over or subsequent collision. A 25cm At least Safety 51

Warning Environment The front passenger must be seated correctly and must avoid When the system is activated, gases are released in the form putting hands, feet or legs on the dashboard since if the front of fumes, together with the gas used for inflating the airbags. airbag is activated, it may cause injury to legs and prevent the These gases are not harmful. airbag from working properly. The driver's airbag has been designed to be deployed according to the following strategy: Operation • For low severity crashes, the airbag control unit will not deploy The front airbags are controlled by an ECU which activates them the airbag when there is a sufficiently severe head-on collision (direction of • For crashes of higher severity, the control unit will deploy the impact between 11 and 1 o'clock p.m.). driver airbag in low energy mode In the event of a collision with an impact force that causes • For crashes of even higher severity, the control unit will deploy deceleration that exceeds the value set for the internal sensor, the the driver airbag in high energy mode. ECU will transmit a signal to deploy the airbags. The airbags will begin to inflate, breaking the cover along the breakage line and will The passenger airbag has been designed to be deployed according deploy completely in a few tenths of milliseconds. Once deployed, to the following strategy: they will serve as protection between the driver and/or passenger • For low severity crashes, the airbag control unit will not deploy and structures that could cause injury. the airbag The airbags deflate immediately afterwards. • For crashes of higher severity, the control unit will deploy the passenger airbag in low energy mode Warning • For crashes of even higher severity, the control unit will deploy the passenger airbag in high energy mode. The driver and passenger should not carry objects (drink cans or bottles, pipes, etc.) that may cause injury if the airbags are activated. Warning Persons, animals or items must not be placed between the The driver and passenger must always fasten their seat belts airbags and the occupant. and sit in an upright position, as far as possible away from the airbag, in order to have optimal protection in all types of collision. 52 Safety

Warning Warning Always keep the backrest of your seat in the upright position Do not place objects above or near the top of the dashboard and sit with your back properly resting against it. and the steering wheel. In the event that the airbags are deployed, these objects would 2 be projected into the passenger compartment at such high speed Important note as to seriously jeopardise the safety of the occupants. Do not modify the system components or wiring, under any circumstances. With the ignition key inserted and in position II, although the engine is off, the airbags can still be activated when the vehicle is stationary if it is hit by a moving vehicle. Remember that if the ignition key is set to 0 none of the safety devices (airbags or pretensioners) is activated in the event of a collision; failure of the airbags to inflate in these circumstances is not indicative of a system malfunction. Important note Do not cut or tamper with the connectors of the airbag harness or on the airbag modules. Warning Do not cover the steering wheel and the padded panel on the dashboard on the passenger side with adhesive tape or treat it in any way. Safety 53

Warning Important note Do not modify the airbag modules in any way (indicated in All the airbag system components must be replaced after an the relevant picture). Do not damage the airbag modules, for accident that caused airbag deployment. example pinning something onto them or pressing objects against their covers. If, for any reason, an airbag cover gets damaged, have the airbag Important note module immediately checked by the Ferrari Service Network. Following an accident not involving airbag deployment, contact Activation of a damaged module could cause serious or fatal the Ferrari Service Network to have the system checked and injuries. any system components that may be damaged or malfunctioning replaced. Important note Important note Do not remove or dismantle parts of the steering wheel, dashboard or door panels; if necessary, this procedure should The airbag system components have been specially designed only be performed by a Ferrari Service Network Centre. only for this specific vehicle model. Do not use them on a different vehicle model, as this may cause serious damage and consequent injury, even fatal, to the occupants in the event of an accident. Warning Damaged or defective components of the airbag system cannot be repaired and must be replaced. Incorrect operations performed on the system components may cause failures or accidental deployment or failure of the airbags to inflate with consequent damage and injury, even fatal. 54 Safety

Environment Warning To scrap the vehicle, please contact the Ferrari Service The passenger seat is not suitable for installing universal Network to have the airbag system deactivated. ISOFIX child car seats. Since the airbag system cannot be deactivated, rear-facing child 2 seats must not be installed. Important note When transporting children who are less than 1.5 m tall, contact If the vehicle has been stolen or there has been an attempted the Ferrari Service Network. theft, have the airbag system checked by the Ferrari Service Network. The label F indicates the presence of the airbag system. F Safety 55

Side airbags Warning Warning The warning light A comes on when the ignition key is turned to position II. If no malfunctions are detected, it goes out after Airbags are not a substitute for seat belts, but they increase their 4 seconds. If the warning light does not come on, if it remains efficiency. Correct use of seat belts, with the supplementary on or if it comes on while driving, contact the Ferrari Service action of the side airbags, offers maximum protection in the Network immediately. event of a collision or vehicle roll-over. Operation Side airbag system components The side airbags are controlled by the ECU that activates them when a sufficiently severe collision occurs. Warning In the event of a side collision with a force of impact exceeding the The side airbags fitted on the vehicle have not been designed limit set by the ECU, this will transmit a signal that activates the to reduce the risk of being thrown out in the event of vehicle pretensioner and the side airbag on the impact side. roll-overs. The vehicle has 2 side airbags, one in the driver-side door panel and the other in the passenger-side door panel. The side airbag system consists of 2 airbags, one on each door. In the event of a side collision, the airbag on the impact side deploys A immediately to protect the occupant's head. 56 Safety

The airbag will start inflating, opening its cover along the breaking line, until it is fully deployed (in a few hundredths of seconds). Warning After deployment, the side airbag will be positioned as a protection Never modify the airbag modules. Do not damage the airbag between the driver’s or passenger’s head and the external structures modules and trim panels above them (upper area of door which could penetrate the passenger compartment and cause injury. panel), by pinning something onto them or pressing objects The airbags deflate immediately afterwards. against their covers, for example. Side airbag activation is not affected by the occupant's height or weight. The side bag is activated whenever the airbag ECU detects a collision of a sufficient impact force for deployment. If, for any reason, an airbag cover gets damaged, have the airbag module immediately checked by the Ferrari Service Network. 2 Activation of a damaged module could cause serious injuries. Warning Never drive with your head out of the window as this places Important note your head and neck in the airbag deployment area. In the event Please consider that the airbag ECU is not capable of of a side-on collision, this position increases the risk of being automatically detecting damages involving the airbag covers. thrown out of the vehicle and compromises the protective effect of the side airbags. Do not cover the upper part of the driver-door and passenger- door panels with adhesive tape or material and do not treat them in any way. Warning Never place an object over or near the airbag covers. Warning In the event that the airbags are deployed, these objects would After deployment, the airbag components can no longer offer be projected into the passenger compartment at such high speed any protection; therefore, they cannot be repaired and must be as to seriously jeopardise the safety of the occupants. replaced. After activation of a side airbag, have it replaced by the Ferrari Service Network. Safety 57

Warning The airbag modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Booklet” EVEN if the vehicle has NOT been involved in a collision. Important note Never remove the door panel. If required, this operation must be performed by the Ferrari Service Network. 58 Safety

Fuel inertia switch The fuel inertia switch is a safety device which deactivates the fuel pump relays if a collision occurs. A specific symbol appears on the left TFT display (see page 109) and the hazard warning lights activate to indicate that this switch has been triggered. When the fuel inertia switch is activated, the doors are also 2 unlocked (if locked) and the central dome light comes on. Warning The fuel pump relays can be reactivated by pressing button A on the floor in front of the driver's seat. A Safety 59

ABS and EBD In the event of ABS activation under braking, these regulation cycles will be repeated until the car comes to a stop or pressure on The ABS system is a safety device which activates to prevent wheel the brake pedal is reduced. locking if the driver presses the brake pedal too sharply, especially The system offers the following advantages: under low grip conditions. - Driving stability (no skidding): even in the event of sharp braking The system is composed of: approaching wheel locking. - electro-hydraulic unit ‑ Manoeuvrability (no side-skidding on sharp turns). - electronic brake-force distribution EBD This means that even when an emergency situation requires sudden - four speed sensors on the wheels, incorporated in the bearings braking, the driver can avoid obstacles, or brake on a curve, without - the entire ESP sensor system (steering angle sensor, affecting the vehicle stability. accelerometer, yaw sensor, etc.). These features add to the vehicle’s standard braking system, Warning without changing its characteristics. ABS system performance remains unaltered as long as the speed limit for the tyre side grip is not exceeded. If this limit is Important note exceeded, vehicle skidding cannot be avoided. When the ABS system is active, during emergency braking or in poor grip conditions, a “pulsing” sensation will be felt through - Optimal braking distance: depending on the type of road surface, the brake pedal. Hold the brake pedal down to continue the the braking distance may be reduced by as much as 40%. braking action. Warning When one of the wheels starts locking, the hydraulic control unit controls the braking circuit by running a 3-phase cycle: The ABS system does NOT exempt the driver from driving carefully and responsibly at all times. - reduction (if necessary) - maintenance - pressure increase in the hydraulic circuit. 60 Safety

Important note The ABS system cannot compensate for driving too fast for traffic or road conditions, worn tyres, worn braking system components or driving errors. The ABS system has been designed for the sole purpose of assisting the driver in controlling braking under extreme conditions in which 2 he/she could instinctively cause the wheels to lock. FBP - Ferrari Brake Prefill Brake design parameters provide a set distance between the brake pads and discs (the “air gap”): as soon as the brake pedal is pressed, the presence of the air gap leads to a slight delay in brake response. The FBP (Ferrari Brake Prefill) system eliminates the air gap by applying slight pressure to the braking system as soon as the accelerator pedal is released just before braking. This results in more immediate brake response and reduces braking distance during emergency braking thereby improving safety. Safety 61

ESC - Electronic Stability Control F1-Trac The electronic stability control ESC consists of two main systems: F1-Trac is a traction control system that derives directly from VDC Vehicle Dynamics Control, performed through the Ferrari's expertise in F1 vehicles. braking system F1-Trac is faster and more accurate than traditional control F1-Trac traction control performed through engine torque systems and is capable of delaying and minimising engine torque modulation, depending on maximum grip on the road adjustments as required in order to ensure the desired trajectory. and secondary systems that are always active such as the ABS and The system estimates the maximum available grip in advance, by EBD. continuously monitoring the relative wheel speed and using an auto-adaptive operating logic. Comparing this information with To provide optimal control in different driving and grip conditions, the vehicle dynamics model stored in the control system, F1-Trac five different settings have been developed: optimises the vehicle behaviour by controlling engine torque - Level 1 (Manettino set to WET): ensures stability and maximises delivery. traction on every type of road surface, both in low and very low grip conditions, by means of engine and brake control (in this condition, the standard ASR system is activated instead of the F1- Important note Trac function). F1-Trac does not work when the Manettino is set to CT OFF - Level 2 (Manettino set to SPORT): ensures stability and and ESC OFF driving modes. maximises traction only in medium- to high-grip conditions by optimising engine and brake control. The main feature that distinguishes the F1-Trac system from a - Level 3 (Manettino set to RACE): enhances the racing features traditional traction control system lies in its ability to estimate grip of the vehicle by optimising traction control and reducing brake level accurately which allows the driver to make full use of the control to a minimum. This mode is designed to ensure stability vehicle's performance driving potential. on the race track in high grip conditions only. The F1-Trac system guarantees: - Level 4 (Manettino set to CT OFF): further enhances the already racing-style behaviour of the vehicle, F1-Trac traction control is - maximum traction when coming out of bends; disabled while stability control remains active when a certain level - driving stability and ease even under extreme driving conditions; of sideslip is exceeded. F1-Trac traction control is off. Stability is - driving comfort. NOT guaranteed. On this vehicle, integration of the F1-Trac and E-Diff 3 systems - Level 5 (Manettino set to ESC OFF): ESC deactivated. Stability ensures maximum performance and stability. is NOT guaranteed, but all the other auxiliary systems such as the ABS, EBD and the E-Diff 3 electronic differential remain active. During braking, the VDC system remains active. 62 Safety

E-Diff 3 The vehicle is equipped with an electronic differential, working on the rear axle, which continually performs a variable check on the locking between the two axle shafts. The electronic differential system, integrated with F1-Trac traction control, is capable of improving: - performance; 2 - directional stability of the vehicle; - active safety even when close to grip limit; - driving comfort and handling. The system is based on the analysis and forecast of vehicle performance in all possible conditions. This is done by continually monitoring the pressure of the clutch actuator on the differential. The input signals are the dynamic parameters of the vehicle that the control system translates into a torque difference between the two driving wheels. In a curve, the electronic differential: - maintains vehicle stability during throttle lift-off by appropriately modulating the engine braking torque applied to the rear axle; - controls vehicle dynamics, for maximum stability and acceleration when exiting the curve, by locking the differential with a strategy that considers all vehicle dynamics parameters. To obtain these results, the electronic differential system interacts with the F1-Trac, ESC and ABS systems, F1 gearbox and suspension damping control. Safety 63

EPB - electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. Always apply the parking brake when the vehicle is parked. The parking brake can be applied and released by pulling a special lever B on the dashboard to the left of the steering wheel. With the The vehicle should be blocked. If this is not the case, please ignition key turned to II, the relative indicator on the instrument contact the Ferrari Service Network. panel (see page 114) lights up to indicate when the parking brake is engaged. Autopark Function Pull the lever B while holding the brake pedal depressed to release the parking brake. If the ignition switch is turned to II, the indicator The EPB Autopark function automatically activates the electric extinguishes once the parking brake is completely released. parking brake when the engine is switched off. At each Key-on, the Autopark function is always active by default: this means that the The electric parking brake may be used as an emergency brake driver does not need to apply the parking brake when the engine is when the vehicle is in motion. If this is the case, the system acts on switched off. all four wheels until button B is released by communicating with the ESP system which prevents locking. However, the function can be temporarily deactivated before switching off the engine by pressing the AUTO PARK C button: the message “PARK OFF” is displayed on the left TFT display for 5 seconds. In this case, after the engine is switched off, the parking brake must be engaged manually by pulling the lever B. To re- enable automatic EPB engagement at the next key-off, press the button C again; the message “PARK ON” is displayed on the left TFT display for 5 seconds. “Automatic Vehicle Holding” AVH function C The Automatic Vehicle Holding function of the electric parking brake ensures optimised release when moving off from a standstill: after engine start, the system uses the service brakes to hold the vehicle instead of the parking brake shoes. See page 162 for further information on the electric parking brake. B 64 Safety

Tyre temperature and pressure monitoring Warning system (TPMS) The TPMS warns the driver that the tyre pressure has The vehicle is equipped with a system that measures the tyre decreased. However, this does NOT exempt the driver from pressure and temperature using special sensors fitted inside the periodically checking that the tyres are inflated to the indicated wheel rims next to the air valve. These sensors transmit a signal pressure. that is received by the antennas on the car body, behind the gravel guards, that are connected to the ECU. In addition, the system does NOT warn the driver of damage to the tyres by external agents. 2 Important note Displaying messages on the left TFT display The system may be momentarily affected by radioelectrical interference from devices that use similar wavelengths. The driver may use the left hand TFT display controls (see page 88) to access the TYRES screen page, which displays the vehicle symbol together with the pressure and temperature values The ECU processes this information and transmits data on tyre of each tyre as shown in the following example 1. pressure and temperature and any system errors to the instrument panel. The signal transmitted by the ECU activates symbols on the left TFT display (see page 88) with two priority levels: a soft warning if the pressure loss is 0.2 bar more than the rated pressure and a hard warning if it is 0.5 bar more or there is a dynamic decrease of over 0.2 bar/min. The TPMS system is calibrated from the specific menu option of the left hand TFT display (see page 90). Important note System calibration using the special menu item is necessary after replacement or inflation of a tyre or tyres. 1 Safety 65

If the TYRES screen page is being displayed and an event occurs The screen page is displayed for 20 seconds and then the screen that needs to be shown as a symbol and/or special message, the page that was previously displayed reappears. If the failure screen page is minimised as shown in example 2. For further persists, the screen page shown above (example 3 or 4) will be information, refer to the paragraph “Fault visualisation logic” on automatically displayed for 20 seconds the next time the engine is page 106. started. The driver can call up the TYRES screen page at any time to Low pressure display which tyres have low pressure (example 5). Regardless of the type of screen page on the left TFT display, when the instrument panel receives the signal from the tyre pressure ECU that the pressure level of one or more tyres is below the alarm threshold, the screen page shown in example 3 (for a warning related to only one tyre) or example 4 (for a warning related to several tyres) appears immediately. Check tyre Check tyre Catalysts temp. pressure pressure too high Engine performance limited 2 3 4 5 66 Safety

Occasionally, the system may not detect which wheel signals The screen page is displayed for 20 seconds and then the screen a failure. If this is the case, then only the message “Check tyre page that was previously displayed reappears whereas the warning pressure” will be displayed as shown in example 6. light remains on in fixed mode. If the vehicle is fitted with normal tyres, the fault is displayed with Tyre puncture the same display logic applicable for other priority 0 faults (see the Regardless of the type of screen page on the left TFT display, when paragraph “Fault visualisation logic” on page 106) until the correct the instrument panel receives the signal from the tyre pressure ECU that the pressure level of one or more tyres is below the operating conditions are restored and the system subsequently recalibrated. 2 alarm threshold, the screen page shown in example 7 (warning If the vehicle is fitted with Run Flat tyres, the maximum distance not to proceed for vehicles fitted with normal tyres) or example 8 allowed in a “tyre puncture” state is 100 km (62 mi). The (warning to proceed at a maximum speed of 80 km/h (50 mph) instrument panel will calculate the residual tyre life and will for vehicles fitted with Run Flat tyres) appears immediately. At the redisplay the screen page shown in example 8 after 50 km (31 mi). same time, a warning light comes on on the panel (see page 112) in The same screen page (warning not to exceed a maximum speed of fixed mode. 80 km/h) is displayed if the vehicle exceeds 80 km/h (50 mph). Once the distance of 100 km (62 mi) has been exceeded, the panel displays the screen page shown in example 7 (warning not to proceed). If you call up the TYRES screen page, you can identify the punctured tyre at any time (example 9). Check tyre pressure Low tyre Low tyre pressure pressure Do not Max speed proceed 80 km/h 6 7 8 9 Safety 67

If another tyre is punctured, the instrument panel will update the Occasionally, the system may not detect which wheel signals a number of km (mi) which can still be driven according to the failure. If this is the case, the screen page shown in example 12 (for distance driven after the previous puncture and will display the vehicles fitted with normal tyres) or example 13 (for vehicles fitted screen page shown in example 10. with Run Flat tyres) will be displayed. While a priority level 0 (normal tyre puncture) or priority level 2 The symbol and message are displayed for 20 seconds and then the (Run Flat tyre puncture with maximum speed limit not exceeded screen page that was previously displayed reappears whereas the and tyres still usable) fault is active on the display, the driver may warning light remains on in fixed mode. press OK to “ESCAPE” (see page 106): the screen page disappears If the vehicle is fitted with Run Flat tyres, the instrument panel will whereas the warning light on the panel remains on in fixed mode. calculate the residual tyre life and will redisplay the screen page As above, the TYRES screen page can be called up at any time to shown in example 13 after 50 km (31 mi). The same screen page display which tyres are punctured (example 11). (warning not to exceed a maximum speed of 80 km/h) is displayed if the vehicle exceeds 80 km/h (50 mph). Once the distance of 100 km (62 mi) has been exceeded, the panel displays the screen page shown in example 12 (warning not to proceed). Low tyre Low tyre Low tyre pressure pressure pressure Max speed Do not Max speed 80 km/h proceed 80 km/h 10 11 12 13 68 Safety

System not calibrated When the Menu item is displayed and the subsequent calibration If the system has not been calibrated or one or more tyres have accepted, the screen page shown in example 15 appears for been replaced, the symbol and message shown in example 14 will 5 seconds. be displayed. Simultaneously, the specific warning light on the instrument panel (see page 112) starts flashing, and continues to Warning flash for 90 seconds. When the display cycle ends (20 seconds), the symbol and message disappear and the screen page that was previously displayed Before calibrating the system, make sure that the tyre pressure corresponds to the indicated pressure values (see page 30). If this is not the case, the TPMS may issue wrong low pressure 2 reappears whereas the warning light remains on until the system indications. has been calibrated. The TPMS can be calibrated using the special menu item in the left TFT display with the ignition key in position II and the engine off. To calibrate the TPMS, call up the MENU screen page on the left TFT display (see page 88) with the ignition key in position II and the engine off. Once the MENU screen page appears, select the items “Car setup”, “Calibr. TPMS”. Display setup Date/Hour TPMS Calibration activated Language/M.U. not calibrated Execute Car setup calibration Dimming 14 15 Safety 69

TPMS failure Simultaneously, the specific warning light on the instrument The screen page shown in example 16 is displayed in the following panel (see page 112) starts flashing, and continues to flash for circumstances: 90 seconds. The warning light then remains on in fixed mode until the situation is corrected. - malfunction in the circuit and/or wiring connecting the ECU The TYRES screen page cannot be called up by the driver. - signal is not received by one or more sensors due to a faulty, broken or flat battery System not active - fault in the TPMS ECU. For a few seconds at key-on, if the TPMS has been deactivated by a Simultaneously, the specific warning light on the instrument diagnostic tool, the screen page in example 18 is displayed. panel (see page 112) starts flashing, and continues to flash for 90 seconds. The warning light then remains on in fixed mode until Simultaneously, the specific warning light on the instrument the situation is corrected. panel (see page 112) starts flashing, and continues to flash for 90 seconds. The warning light then remains on in fixed mode until The TYRES screen page cannot be called up by the driver. the situation is corrected. The TYRES screen page cannot be called up by the driver. System temporarily not active The screen page shown in example 17 is displayed in the following circumstances: - overheating of sensors - during calibration (the TPMS ECU does not recognise the sensors) - radio frequency that interferes with the wheel sensor signal. TPMS failure TPMS TPMS inactive temporarily inactive 16 17 18 70 Safety

Controls overview................................................... 74 Ignition switch........................................................ 76 Doors.................................................................... 78 Engine compartment lid.......................................... 80 Luggage compartment lid....................................... 81 Fuel filler flap and neck........................................... 83 Power windows...................................................... 85 Instruments and gauges.......................................... 86 Parking sensors.................................................... 102 Infotainment system............................................. 122 Cruise Control...................................................... 130 Controls on the steering wheel.............................. 132 Lighting................................................................ 138 Driving the vehicle................................................ 144 EPB - Electric parking brake.................................. 162 Park Lock............................................................. 164 Launch Control.................................................... 165 Stop&Start system (optional)................................ 166 Front obstacle clearance lift system (optional)....... 174 Active CCM brake cooling system.......................... 176 Seat adjustment................................................... 178 Air conditioning and heating system...................... 186 Passenger compartment accessories...................... 193

3 ABOUT YOUR VEHICLE

Controls overview 3 3 4 1 2 5 6 Ref. Control Page Ref. Control Page 1 Door handle 79 4 Passenger display (optional) 121 2 Luggage compartment and fuel filler flap 81-83 5 Glove compartment opening button 193 opening buttons 6 Glove compartment 193 3 Adjustable air vents 189 74 About your Vehicle

2 3 4 1 3 6 5 Ref. Control Page Ref. Control Page 1 Left TFT display and Cruise Control commands 88-130 4 Right TFT display (Infotainment system) 118 2 Dual View Camera button (optional) 120 5 Light switch 138 3 LIFT button (optional) 174 6 EPB command and Autopark button 162 About your Vehicle 75

Ref. Control Page Ref. Control Page 13 Left TFT display 88 22 Power window controls 85 14 Rev counter and gearbox display 115-116 23 Hazard warning lights control 141 15 Right TFT display 118 24 “LAUNCH” control 164 16 Turn indicators 140 25 “AUTO” control 150 17 Windscreen washer/wiper lever 135 26 “R” reverse control 147 18 “Manettino” control 132-156 27 Air conditioning controls 186 19 “ENGINE START” button 132 20 Suspension damping delink button 134-160 21 High beam and flashing lever 138 13 14 15 27 22 23 26 16 16 25 21 24 17 20 18 19 76 About your Vehicle

Ignition switch Warning The ignition key can be turned to 2 positions: Never remove the key when the vehicle is moving! Position 0 - Stop The steering wheel will lock with the first turn of the steering wheel. Engine off, key removable. Always remember to remove the key from the ignition when you When the key is even only partially extracted, the steering column get out of the vehicle. is locked. Never leave vulnerable persons (children, the elderly) The hazard warning lights and parking lights can be activated. unattended in the vehicle. To facilitate steering wheel release, turn the steering wheel slightly clockwise or counterclockwise while turning the ignition key. Key Lock 3 Position II - Start If more than 20 seconds elapse after turning the key to position 0, When the key is turned to this position (key-on) the signals the key lock device must be released to remove the key: press generated by the vehicle systems are checked. button K and remove the key at the same time. The left and right TFT displays are activated on the instrument panel and when the signals have been checked, the gearbox display comes on (see page 116). K II 0 About your Vehicle 77

Doors Locking and opening the doors from the inside When a door is opened or closed, the window automatically moves down by approximately 2 centimetres / 0.8 inches (to its “target Warning position”) to avoid colliding with the upper weather strip. Always check carefully and also manually that the doors have When the door is closed, the window automatically moves up until been closed properly to prevent them opening while driving. it reaches the “upper limit”. Both doors may be locked and unlocked by pressing the LOCK/ Opening from the outside UNLOCK button B on the ceiling. To lock the doors, press Using the remote control, deactivate the alarm and the central door button B; when the door lock is activated, the light on the button locking system, or turn the key in the lock to deactivate the central comes on. To deactivate the door lock, press button B until the door locking system. light goes out. To open the door, pull handle A: the window will move down to its The rolling lock function, which automatically locks the doors when “target position”. When the door is closed, the window will move the vehicle speed reaches or exceeds 20 km/h, may be activated up until it meets the upper limit. from the “Car setup” menu accessible from the left hand TFT display of the instrument panel (see page 88). B A 78 About your Vehicle

If you pull handle C to open the door, the window will move down to its target position. When the door is closed, it will move up until it meets its upper limit. If handle C is lifted without opening the door, the window will move down to its target position and stop and if the door is not opened after 2 seconds, the window will move back up until it meets the upper limit. Therefore, to open the door, release handle C and pull it again. When the opening handle is operated, both doors are unlocked. 3 C About your Vehicle 79

Engine compartment lid Closing Lower the lid until it is closed and press down near the lock until you hear it click in place. Opening To unlock the engine compartment lid, pull the lever D underneath the steering column. Warning Stand in front of the vehicle, slightly lift the lid and pull the Always check manually that the engine compartment lid has retaining lever E to the side of the lock and lift it. been closed properly to prevent it from opening while driving. The lid is held open by two gas struts. The engine compartment lid can also be opened with the ignition key at off. D E 80 About your Vehicle

Luggage compartment lid Important note Opening After disconnecting the battery from the electrical system, a door lock/unlock cycle must be performed using the buttons on The luggage compartment lid can also be opened with the ignition the key when reconnecting so that the release button G resumes key at off. normal operation. Push release button G on the driver-side door or press button H on the ignition key for more than 2 seconds. The lid is held open by two gas struts L. Closing The luggage compartment is illuminated by two lights at the sides Grasp the handle on the right of the luggage compartment lid, that come on automatically when the lid is opened. lower it until it is closed and press down near the lock until you hear it click in place. 3 Warning To avoid damage, check there is enough room to open the Warning luggage compartment lid. Always check manually that the luggage compartment lid has been closed properly to prevent it from opening while driving. H L G L About your Vehicle 81

Emergency Opening There is an emergency manual release cable situated on the front left hand edge of the luggage compartment lid, under the cover N, for use if the luggage compartment lid release button does not work. N 82 About your Vehicle

Fuel filler flap and neck Closing To close the fuel filler flap, push it until it clicks in place. Warning Emergency Opening Always turn off the engine during refuelling. If the opening button does not work, the fuel filler flap can be Do not smoke or use naked flames when refuelling. There is a opened manually by pulling the cable P on the right-hand side of risk of fire. the luggage compartment. The following can be harmful for your health: - fuel coming into contact with your skin - inhaling fuel vapours. 3 Opening To open the fuel filler flap, press button M on the driver-side door. M P About your Vehicle 83

Capless filler neck This vehicle has a capless filler neck for fuelling. This system allows Warning you to refuel by opening the fuel filler flap and simply placing the Place the nozzle in the filler neck carefully to avoid damaging nozzle in the filler neck without having to unscrew a cap. the device seal. Two flaps placed in series, both with airtight seals, act as a cap. Do not try to open the external flap of the filler neck by pushing The external flap is locked by a series of “teeth” and the only way it with your fingers or lever it open using unsuitable tools (e.g. to open the external flap correctly is by inserting a petrol pump screwdrivers). This may damage the external flap mechanism nozzle. and the seal, or generate sparks that could cause a fire if fuel is present. Warning Do not overfill the fuel tank: this may cause the fuel to leak out. After fuelling, wait for about 5 seconds before slowly removing the nozzle from the filler neck: in this way, the last drops of fuel will flow into the tank and will not drip onto the vehicle. Warning Do not place funnels or portable container nozzles in the filler neck. If you need to refuel from a portable fuel container, use only the funnel in the tool kit (see page 198) that releases the automatic closing device. 84 About your Vehicle

Power windows Passenger-side power window Use button B to move the passenger side window up or down. The power windows can only be used with the ignition key in position II. Only manual operation is possible (partial opening) to raise the window: when button B is released, the window stops at the position reached. Driver-side power window To lower the window, automatic operation is also possible (full Use button A to move the driver-side window up or down. opening): if the button is pressed at length (over 0.3 seconds) Press or push button A quickly to activate manual operation (partial automatic window operation is activated. The window will only opening/closing): when the button is released, the window stops at stop when it reaches the end of its travel or by pressing the button the position reached. again. If the button is pressed/pushed at length (over 0.3 seconds), automatic window operation (complete opening/closing) is activated. The window will only stop when it reaches the end of its Warning 3 travel or by pressing/pushing the button again. Improper use of the power windows can be dangerous. Before use, always check that people and objects are at a safe distance. Pay particular attention during the automatic operation of the driver-side power window. To protect the passengers remaining in the car against accidental activation of the power windows, always remove the key from the ignition. B A About your Vehicle 85

Instruments and gauges 6 5 2 5 3 7 1 5 4 5 86 About your Vehicle

1 Left TFT display 3 2 Rev counter 3 Right TFT display 4 Gear display 5 Warning lights on the panel 6 Manettino status 7 Fuel level About your Vehicle 87

Left TFT display MAIN screen page Located on the instrument panel, it performs the following If you press the MAIN button, you activate the MAIN screen page functions: which can be used to access the four screen page groups SETUP, VDA, TRIP and STATUS. These groups contain the following screen - displays the control parameters pages: - displays general information while driving SETUP (pressing the UP button) - displays fault warnings. MENU screen page The driver can interact with the system by selecting the STATUS (pressing the DOWN button) configuration and setting the parameters using the controls on the dashboard to the left of the steering wheel. SPORT screen page SPORT 2 screen page The display is activated and set by pressing the MAIN (A), TYRES screen page VDA (B), OK (C) and UP, DOWN, LEFT, RIGHT (D) buttons. VDA (pressing the LEFT button) Chronometer screen page Vehicle status screen page Manettino status screen page TRIP (pressing the RIGHT button) TRIP A screen page TRIP B screen page. A B C D 88 About your Vehicle

Press the RIGHT and LEFT buttons to sequentially switch between Every screen page consists of four display areas: screen pages in a group. Press RIGHT to go to the next screen page A - selected driving mode (Manettino position), windscreen wiper (for example, in the STATUS group from SPORT to SPORT 2) status, outside temperature and “Warning: danger of ice” icon. and press LEFT to go to the previous screen page. Press the RIGHT B - display of virtual control gauges, parking sensor screen page, button after the last screen page to go back to the first screen page display of abnormal events/warnings (message text and special and press the LEFT button after the first screen page to go back to symbol, when available), display of brightness adjustment the last screen page. function. When a screen page is called up, it remains on the display until you C - total or trip odometer (TRIP A or B), range. decide to select another one. D - fuel level gauge, area for minimised symbol for faults that do not have a specific warning light on the panel (see page 106), speed repetition. 3 About your Vehicle 89

Display setting and configuration of vehicle parameters Navigation within the menu is on several levels; the first level offers a list of items through which the following parameters can be set or the following information can be displayed: Warning - Dimming: display dimming setting Display setting and parameter configuration should be - Display setup: display setting performed when the vehicle is stationary. - Date/Hour: date and time setting - Language/M.U.: language and units of measurement setting MENU screen page - Car setup: vehicle parameter configuration Display setting and configuration of the various vehicle parameters - Calibr. TPMS: Calibrating the TPMS system is possible using the MENU screen page (the only screen page in - Service: information on scheduled maintenance. the SETUP group) that can be directly called up by pressing the UP These items are the main menu functions. To scroll through the list button when the MAIN screen page is activated. of items, press the UP and DOWN buttons; to select the required function, press and quickly release the OK button or the RIGHT button. Dimming M.U. Distance Display setup M.U. Temp. Date/Hour Language Language/M.U. Language/M.U.. M.U. Pressure Car setup 90 About your Vehicle

Once the function has been selected, the individual subfunctions or Adjusting brightness parameters that can be activated are displayed. To select them, use The brightness of the two TFT displays on the instrument panel the UP and DOWN buttons and press and quickly release the OK can be adjusted by selecting the special item on the MENU screen (or RIGHT) button to activate another subsection or activate the page or by using the UP and DOWN buttons when the MENU selected parameter. screen page is not displayed or the chronometer is off if the To go back to a previous level in the menu hold down the OK Chronometer screen page is displayed. button, press the LEFT button or select the BACK item which is The first time one of the two buttons is pressed, the screen page normally in the list of subfunctions. If no operation is performed is displayed. The next time the buttons are pressed, the brightness for at least 10 seconds, the first menu level reappears on the can be adjusted. display. The adjustment made, which can be activated even when the vehicle is moving, can be seen immediately and does not affect the brightness of the warning lights on the panel. The screen page disappears when the OK button is pressed or 3 automatically if it is not used for 5 seconds and is replaced by the screen page that was previously displayed. DIMMING About your Vehicle 91

Date and time setting To set the date, call up the MENU screen page, select “Date/Hour” and “Date” and set the day, month and year using the UP, DOWN and OK buttons. To set the time, call up the MENU screen page, select “Date/Hour” and “Hour” and set the time using the UP, DOWN and OK buttons. By selecting “Date /Hour” and “Hour” you can also choose to display the time in the 24h or 12h format. 92 About your Vehicle

Fuel level gauge In limited cruising range conditions, the information on driving range in km is replaced by the words “Limited cruising range”. The fuel level gauge is always displayed in area D of the display (see page 89). The gauge has 9 yellow bars that gradually “turn off” as the fuel level drops. When the second bar goes off, the first bar turns red until fuel runs out. When the reserve fuel is reached, in addition to the activation of 3 the relative warning lamp on the instrument panel (see page 109), the relative symbol and specific message, together with the remaining range in Km, are shown on the display for 10 seconds. If the condition that has generated it persists, this signal is repeated every 8 km (5 mi). Fuel level Fuel level Low low Limited Range cruising 86 km range About your Vehicle 93

SPORT screen page SPORT 2 screen page The SPORT screen page displays the following virtual gauges: The SPORT 2 screen page displays the following virtual gauges: - Engine coolant temperature - Engine oil pressure - Engine oil temperature. - Voltmeter. If the SPORT screen page is being displayed and an event occurs If the SPORT 2 screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the that needs to be displayed as a symbol and/or special message, the virtual gauges are minimised. For further information, refer to the virtual gauges are minimised. For further information, refer to the “Fault visualisation logic” paragraph on page 106. “Fault visualisation logic” paragraph on page 106. 94 About your Vehicle

TYRES screen page VDA (Vehicle Dynamic Assistance) screen page group The TYRES screen page displays a vehicle symbol with the In addition to its chronometer function, the Vehicle Dynamic pressure and temperature values for each tyre. Assistance (VDA) screen page group provides a valid support for If the TYRES screen page is being displayed and an event occurs assessing vehicle status when on the track and can be used to that needs to be displayed as a symbol and/or special message, intuitively understand the most suitable conditions for performance the screen page is minimised. For further information, refer to the driving. The VDA group, which is recalled by pressing the LEFT “Fault visualisation logic” paragraph on page 106. button with the MAIN screen page displayed or directly by pressing the VDA button with any screen page displayed, consists of the “Chronometer”, “Vehicle status” and “Manettino status” screen pages. The “Vehicle status” screen page functions are only available when the “Manettino” driving mode control switch (see page 130) is set to RACE, CT OFF or ESC OFF, positions developed especially 3 when using the vehicle on track; however, if the Manettino is set to WET or SPORT mode, the “Vehicle status” screen page is displayed along with the message “VDA not available in WET - SPORT”. VDA not available in WET - SPORT About your Vehicle 95

Chronometer screen page During display of the event/malfunction, the chronometer remains The “Chronometer” screen page is used to time laps and memorise active. lap time if the vehicle is used on track. The screen page displays the Each time the key is turned to on, the chronometer is reset whereas following information: the last valid Best Lap and Last Lap information is memorised. Current Lap indicates the time elapsed since the start of the chronometer Chronometer operation logic LAP TIME / Best The chronometer is controlled using the OK, UP and DOWN indicates the time required to complete the last best lap buttons that perform the following functions: LAP TIME / Last - Pressing and quickly releasing the OK button: indicates the time required to complete the last lap when the chronometer is off, starts the Current Lap chronometer TOP SPEED / Best when the chronometer is on, resets and restarts the Current Lap indicates the maximum speed reached and updates the information on previous laps (end of lap/start of TOP SPEED / Last next lap) indicates the maximum speed reached in the last lap. - Pressing and quickly releasing the UP or DOWN button: If the “Chronometer” screen page is being displayed and an event when the chronometer is on, stops the chronometer and updates occurs that needs to be displayed as a symbol and/or special information on previous laps message, the screen page is minimised. For further information, when the chronometer is off, displays the screen page for adjusting refer to the “Fault visualisation logic” paragraph on page 106. display brightness - Holding down the UP or DOWN button: when the chronometer is on or off, resets the chronometer and information on previous laps. LAP TIME Note that during display of an event/malfunction, pressing and Best: 1:11:00 quickly releasing the OK button interrupts the event/malfunction Current LAP Last: 1:14:40 display cycle (“ESCAPE” function), without affecting the 1:12:10 TOP SPEED chronometer. Best: 247 Km/h Last: 230 Km/h 96 About your Vehicle

Vehicle status screen page OVER The “Vehicle status” screen page, which is directly called up by One or more systems have reached an overheating condition pressing the VDA button or by pressing the LEFT button when the that may affect vehicle dynamics. Slowing down is therefore MAIN screen page is displayed, is intended to help the user bring recommended to restore these systems to optimum conditions of the vehicle to optimum performance when driving on high grip use. surfaces. This is made possible by an algorithm that determines the thermal state of the main vehicle subsystems (tyres, brakes and engine) in relation to the dynamics of various parameters (lateral acceleration, speed, etc.). The status of the vehicle is displayed concisely using three levels which are blue, green and red: WARMUP Warm-up stage for components and self-acquisition of control WARMUP GO OVER 3 systems; during this stage, the vehicle should be driven so that it is taken to optimum conditions of use. GO The vehicle has completed the warm-up stage: all its subsystems have reached optimum conditions of use for performance driving. WARMUP GO OVER WARMUP GO OVER About your Vehicle 97

After each start, the ESC stability and traction control system If one or more signals related to the performance parameters used compensates for the tyre rolling radius and detects the spare to calculate the thermal state of the subsystems (lateral acceleration, wheel. While this procedure is being performed, the Vehicle Status speed, etc.) are not valid, the “Vehicle Status” screen page indicates screen page indicates to the driver that system self-acquisition is in to the driver that the function is not available by displaying the progress by displaying the message “ESC Autolearning”. message “Function not available”. Warning Use of the vehicle on race tracks: after each start, cover the first straight stretch of the track (at least 500 meters / 0.3 mi) at a constant speed so that the ESC stability and traction control system can calculate exactly the grip available and the rolling radius of the tyres (the calculation is reset every time the engine stops). Failure to observe this rule may lead to reduced system performance. The vehicle, which has been designed and produced for road use, should only be used occasionally on race tracks. WARMUP ESC Autolearning WARMUP Function not available 98 About your Vehicle

Manettino status screen page If one of the other two VDA screen pages is displayed The “Manettino status” screen page displays a list of parameters (“Chronometer” or “Vehicle Status”), the “Manettino Status” screen which can be configured using the “Manettino” driving mode page is displayed in timed mode for 3 seconds when the position of control switch (see page 132) and indicates the configuration each the Manettino is changed so that the driver is informed of the new one assumes in a specific driving mode. status that the systems are in. After 3 seconds, the screen page that was previously displayed reappears. The systems involved are the following: The “Manettino status” screen page is also automatically displayed - F1-Trac: traction control in timed mode at key-on if one of the other two VDA screen pages - E-Diff: electronic differential was displayed at the previous key-off and the Manettino was in a - F1-DC: dual clutch F1 gearbox different position from the current one. - ESC: stability and traction control - ABS: anti-lock braking system Important note 3 - S CM: magnetorheologically controlled suspension. If there is a Manettino failure, the “Manettino Status” screen page cannot be displayed or recalled. VEHICLE DYNAMICS F1-Trac E-Diff F1-DC ESC ABS SCM About your Vehicle 99

TRIP A and TRIP B screen pages “Warning: danger of ice” message The TRIP A or TRIP B screen page displays the following To warn the driver of the presence of ice on the road if the outside information: temperature is 3 °C (38 °F) or below, the “snow” symbol and the - Maximum speed “warning: danger of ice” message are displayed for 10 seconds in - Average speed the top right of the display. - Travel distance When they are displayed, the symbol and message appear instead of the outside temperature; after 10 seconds, the outside temperature - Travel time is displayed again and the “snow” symbol appears next to it as long - Range as the outside temperature remains 6 °C (43 °F) or below. If the TRIP A or TRIP B screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the screen page is minimised. For further information, refer to the “Fault visualisation logic” paragraph on page 106. Warning: danger of ice TRIP A Mon 16 Nov Maximum speed 263 Km/h Average speed 124 Km/h Travel distance 292.8 Km Travel time 03:36 h:m Range 204 Km 100 About your Vehicle

Speed limit setting and “Speed limit exceeded” message When the set limit is exceeded, the driver is informed in the following way: The MENU screen page can be used to set a speed limit in the range 30 - 250 km/h (17 - 155 mph) with 5 km/h (3 mph) steps The symbol showing the set limit and a “Speed limit exceeded” which sends a message to the driver when exceeded. To set the message appear in the top right of the display for 10 seconds speed limit, call up the MENU screen page by pressing the UP accompanied by an acoustic signal. Once the warning cycle has button when the MAIN screen page is activated. Select “Car setup” ended, the message disappears whereas the symbol continues to be and “Speed limit”. displayed next to the outside temperature until the speed decreases to 5 km/h (3 mph) below the set limit. To set the value, use the UP and DOWN buttons. When the minimum limit of 30 km/h (18.6 mph) is reached, press the DOWN button again to deactivate the function or press the UP button after reaching the maximum speed of 250 km/h (155 mph). The function is normally deactivated (OFF). 3 120 Speed limit exceeded About your Vehicle 101

Parking sensors The rear parking sensors are automatically activated when the key is in position II and reverse gear is engaged. When the rear sensors To help the driver when parking, the vehicle is fitted with four are activated, an acoustic signal warns the driver that the system sensors in the rear bumper (rear parking sensors) and four sensors has been activated. The front parking sensors can be activated/ in the front bumper (front parking sensors). deactivated by pressing the relative button on the roof panel (see page 143). Warning “Stop and Go” function The system will only operate correctly if the sensors on the bumpers are free of mud, dirt, snow or ice. The “Stop & Go” function automatically activates the front sensors when vehicle speed is 10 km/h (6 mph) or below. This system has been designed to assist the driver in certain traffic conditions As the vehicle approaches obstacles to the front or rear, the parking (e.g. tailbacks) and signals when the minimum distance is reached sensors inform the driver of the distance between the vehicle and between the vehicle and the vehicle in front. the obstacle with an audible warning signal which increases in frequency as the obstacle becomes closer, and graphically in area B To activate or deactivate the system, call up the MENU screen page, of the left hand TFT display (see page 89). By supplementing the select the items “Car setup”, “Parking sensor”, and select one of the driver's direct visual information with that provided by the system two options, “STOP&GO ON” and “STOP&GO OFF”. acoustic signals and visual warnings, potential collisions can be avoided when parking. Indication of obstacles The parking sensor system emits acoustic signals as soon as an Warning obstacle is detected which become more frequent as the obstacle approaches. The acoustic signal stops immediately if the distance It is the driver, however, who holds full responsibility for from the obstacle increases whereas the tone cycle remains parking manoeuvres and other potentially dangerous situations. constant if the measured distance from the central sensors remains The system has only been designed as an aid during parking unchanged. manoeuvres since it detects obstacles that are outside the The vehicle symbol and sensor detection zones appear on the driver's field of vision. left TFT display: these zones indicate which part of the vehicle Use of the sensors therefore does not mean that the driver can is approaching an obstacle (if front or rear and if left, right or be less careful and attentive and not watch out for persons and central) and the distance from the obstacle (maximum, medium or obstacles during parking manoeuvres. minimum). 102 About your Vehicle

If an obstacle is detected at maximum distance in the central front If an obstacle is detected at minimum distance in the central front part, it will be displayed as shown below (green). part, it will be displayed as shown below (red). If an obstacle is detected at medium distance in the central front The distances between the vehicle and obstacles detected by the part, it will be displayed as shown below (orange). rear sensors are represented graphically by the colours green, orange and red as follows: Maximum distance (green): 85 to 65 cm - 33.5 to 25.6 in. (150 to 65 cm - 59.1 to 25.6 in. in central zone) Medium distance (orange): 64 to 41 cm (25.2 to 16.1 in.) Minimum distance (red): 40 to 0 cm (16 to 0 in.). 3 About your Vehicle 103

If the front sensors are deactivated, the display does not show the If the parking sensor system symbols are being displayed and an symbols in the front. In the same way, if front sensors are fitted event occurs that needs to be displayed as an icon and/or special and the rear ones are not activated, the display only shows the message, the symbol is moved from the centre of the display to the symbols in the front. If all the sensors are activated, the system can right as shown below. give several pieces of information at the same time: if an obstacle is detected at a maximum distance in the front central part and at Cleaning the sensors a minimum distance in the rear right part, it will be displayed as When cleaning the sensors, be very careful not to scratch or shown below. damage them and avoid using dry, rough or hard cloths. The sensors must be washed with clean water and car shampoo added if necessary. In car washes that use steam jet or high pressure water cleaning equipment, quickly clean the sensors keeping the nozzle at a distance of at least 10 cm (4 in.). For the repainting of bumpers or retouching the paintwork in the sensor area, contact the Ferrari Service Network. If paint is applied incorrectly, it may prevent the parking sensors from working properly. Catalysts temp. too high Engine performance limited 104 About your Vehicle

Indication of parking sensor failure The system ECU checks all the components each time the reverse Important note gear is engaged. If at least one parking sensor is faulty, the special The signals sent by the sensors may also be affected by damage symbol (see page 113) is displayed on the left TFT display together to the sensors caused by dirt, snow or ice on the sensors or with the message “Parking sensor failure. Warning! Possible by ultrasound systems (e.g. pneumatic brakes on lorries or obstacles” accompanied by an acoustic signal. pneumatic drills) in the vicinity. Important note Warning The sensors are able to detect obstacles with reasonably large, even surfaces (e.g.: poles with diameters of over 60 mm (2.4 in.), It is the driver, however, who holds full responsibility for walls, barriers, trees). Detection is not optimum with obstacles with sharp projections or uneven surfaces. parking manoeuvres and other potentially dangerous situations. The system has only been designed as an aid during parking manoeuvres since it detects obstacles that are outside the 3 driver's field of vision. Important note Use of the sensors therefore does not mean that the driver can During parking manoeuvres, always take the utmost care since be less careful and attentive and not watch out for persons and obstacles may be located above or below the sensors. obstacles during parking manoeuvres. Important note Objects placed close to the rear part of the vehicle are not always detected by the system and may therefore damage the vehicle or be damaged themselves. About your Vehicle 105

Fault display When the display cycle ends, if the fault has a special warning light on the panel, the screen page prior to the anomaly is displayed again, and the symbol is not minimised in area D. The warning Fault visualisation logic light on the panel stays on until the cause of malfunctioning has When a fault occurs, the corresponding warning light (if present) been resolved. comes on on the panel whereas a description of the fault (if If the fault is resolved within 20 seconds, it remains displayed and available) and the relevant symbol (if available) are displayed on the warning light remains lit for 2 seconds. the left TFT display. The message appears on the display as soon as the warning light (if present) comes on and the main screen page “ESCAPE” function that is displayed at that time is reduced. Displaying a fault on the screen can be interrupted by pressing and The fault remains on the display for 20 seconds. When the display quickly releasing the OK button with “ESCAPE” function. When cycle ends, if the fault does not have a special warning light on the the OK button is pressed, the screen page that was displayed prior panel, the symbol remains minimised in area D of the display (see to the event reappears. If the fault does not have a special warning page 89) until the cause of malfunctioning has been resolved. In light on the panel, the symbol remains minimised in area D until area B the main screen page is displayed in “maximum” size. the cause of malfunctioning has been resolved. Catalysts temp. too high Engine performance limited 106 About your Vehicle

Fault priority levels Indication of failure of turn indicators and running lights The simultaneous display of several faults follows a logic that A failure of the running lights (front and/or rear) and turn depends on the priority level assigned to it. indicators (front and/or rear) is indicated in the same way as other Priority level 0 - Extremely critical fault faults but the vehicle symbol with the faulty running light or turn indicator indicated in red is displayed together with a description Priority level 1 - Critical fault of the failure instead of the “External lights failure” symbol (see Priority level 2 - Non-critical fault. page 110). When the display cycle ends or the OK button with When several fault events occur at the same time, faults with “ESCAPE” function has been pressed, the “External lights failure” priority level 0 are displayed first, followed by priority level 1 symbol is minimised. and then priority level 2. The information on the various faults is displayed in turn for 5 seconds each. In any case, the total display time for each fault is never less than 20 seconds. If a fault message with priority level 1 or 2 is being displayed, and 3 a new anomaly with the same priority level occurs, the last fault message is only displayed after the first fault message has been displayed for at least 2 seconds. If, on the other hand, another new priority level 0 fault occurs, this is displayed immediately. Lamp failure About your Vehicle 107

“Doors, engine or luggage compartment lid open” function display If one or more doors or the engine and/or luggage compartment lid are open, the vehicle symbol appears on the display and indicates which doors or lids are open together with a special message. If the vehicle is in motion, an acoustic signal is also emitted. When the display cycle ends or the OK button with “ESCAPE” function has been pressed, the special symbol is minimised (see page 112). Doors open 108 About your Vehicle

List of left hand TFT display symbols TFT Warning Description and warnings (priority level) and instrument panel warning lamps light TFT Warning Description and warnings (priority level) Alternator failure light red Indicates there is a fault in the recharging Alarm system failure red system (1). Indicates a fault in the alarm system (1). Low windscreen washer fluid level orange orange The system is not programmed (2). Indicates a low level of washer fluid in the Failure and system not programmed (1). orange windscreen washer tank (2). Oil temperature Contact the Ferrari Service Network. Alarm system failure (2). red red Indicates that the engine oil temperature is too high (0). 3 Break-in attempted (2). Turn off the engine and contact the Ferrari orange Service Network. Fuel level low Adaptive headlights failure Indicates that the fuel level is too low (2). orange Symbol and warning light in flashing mode orange orange indicate there is a failure in the adaptive orange Battery conditioner connected headlight system (2). When the instrument panel is on, it indicates Windscreen wiper motor failure that the battery conditioner is connected (0). Indicates a windscreen wiper motor failure (2). Inertia switch orange Indicates that the inertia switch has been Engine coolant temperature orange activated following an accident and the resulting cut-out of the fuel supply (0). Indicates that the engine coolant temperature red is too high (0). red The hazard warning lights are also automatically activated. Turn off the engine and contact the Ferrari Service Network. About your Vehicle 109

TFT Warning Description and warnings (priority level) TFT Warning Description and warnings (priority level) light light Engine oil pressure Stop lights failure red Indicates that the engine oil pressure is too low Indicates a system failure or blowing of the red (0). orange stop light bulb (2). External lights failure Turn off the engine and contact the Ferrari Service Network. Indicates a system fault or blowing of a bulb orange in the running, turn indicator or rear fog lights A flashing warning light indicates an engine oil (priority level 2). red pressure sensor failure (2). Number plate lights failure Indicates a system failure or blowing of the Contact the Ferrari Service Network. orange number plate lights bulb (2). Engine diagnostic system (EOBD) failure Rear fog lights While the engine is running, it indicates a Indicates a rear fog light failure. orange orange fault in the emission control system and in the orange ignition/injection system (priority level 0). Twilight sensor failure Turn off the engine and contact the Ferrari Indicates a twilight sensor failure (2). Service Network. orange High beams After turning the ignition key to position II, it Indicates that the high beam lights are on. remains on for a self-check for a few seconds blue after the engine has started. The light also comes on when flashing. Running lights Right turn indicator Indicates that the running lights or low beam Indicates that the right turn indicator is on. green lights are on. green Left turn indicator Indicates that the left turn indicator is on. green 110 About your Vehicle

TFT Warning Description and warnings (priority level) TFT Warning Description and warnings (priority level) light light Hazard warning lights ABS green Simultaneous switching on of the right and left Indicates an ABS system failure (1). turn indicator warning lights indicates that the orange orange hazard warning lights are on. The standard braking system is still Catalytic converter temperature functioning. Contact the Ferrari Service Network. Indicates that the catalytic converter red temperature is too high: stop the vehicle (0). ESC off Contact the Ferrari Service Network. orange orange Symbol and warning light indicate that the ESC system has been deactivated (1). The symbol is displayed for 5 seconds together 3 Indicates that the catalytic converter temperature is very high: reduce speed until with the “ESC off” message. the symbol goes out (1). ESC system failure orange Indicates a failure of the catalytic converter Indicates a fault in the ESC system (1). temperature sensor (0). orange orange Checking the engine oil level Warning Indicates a low engine oil level (0). Stop the vehicle and avoid sudden braking orange or steering. Stop driving and contact the Seat heating Ferrari Service Network immediately. For vehicles with Full Electric seats (optional), orange indicates that the heated seat function has been activated (the symbol and message remain Warning displayed for 5 seconds). The vehicle can still be driven at low speed Power steering failure (max. 40 km/h - 25 mph) to clear the road. Indicates that the power steering system is inefficient (2). ESC system activation (flashing warning light) orange Indicates that the ESC system has been orange activated (1). Contact the Ferrari Service Network. About your Vehicle 111

TFT Warning Description and warnings (priority level) TFT Warning Description and warnings (priority level) light light CCM brake discs worn TPMS Indicates that the carbon ceramic brake discs orange Indicates a puncture in one or more standard orange are worn (2). orange tyres (0) or Run Flat tyres (2). With the warning light in flashing mode for a Contact the Ferrari Service Network. maximum of 90 seconds after which it remains on in fixed mode, it indicates: CCM active brake cooling system ON A failure in the TPMS (2). Indicates that the CCM active brake cooling system is activated. TPMS temporarily inactive (2). TPMS inactive (2). CCM active brake cooling system failure TPMS not calibrated (2). Indicates a CCM active brake cooling system orange failure. TMPS calibration Indicates that calibration of the TPMS has Contact the Ferrari Service Network. green been activated. CCM brake disc temperature high Doors/front and rear lids open CCM Indicates that the CCM brake disc temperature The symbol, which is minimised, indicates that is high. one or more doors and/or lids are open or not orange red properly closed. CCM brake disc temperature too high CCM Driver-side seat belt not fastened Indicates that the CCM brake disc temperature Indicates that the driver-side seat belt has not red is too high. red been fastened, together with an acoustic signal Airbag system failure lasting 90 seconds (0). Indicates an airbag system failure (0). Passenger-side seat belt not fastened red red With the warning light in flashing mode, it Indicates that the passenger-side seat belt has indicates that the airbag test cycle has not been red red not been fastened (0). completed (0). Contact the Ferrari Service Network. 112 About your Vehicle

TFT Warning Description and warnings (priority level) TFT Warning Description and warnings (priority level) light light Speed limit exceeded Suspension control system failure Indicates that the speed set by the driver has Indicates a malfunction in the suspension been exceeded; the figure shown indicates the orange control system (2). set speed (2). E-Diff system failure Contact the Ferrari Service Network. E-DIFF Indicates an electronic differential failure (1). “LIFT” status orange When on in fixed mode, it indicates that the 3 green Lift system is activated (vehicle raised). E-DIFF When on in flashing mode, it indicates that red the Lift system is being operated (activation or Brake malfunction deactivation cycle). Indicates that the brake fluid level is low (0). “LIFT” system failure red Indicates an EPB (electric parking brake) Indicates a front “Lift” system failure (1). red failure (0). orange Indicates an overhaul of the Parking Brake Brake pad wear system (0). Indicates excessive wear of the brake pads (2). red red Indicates an EBD system failure (0). Contact the Ferrari Service Network. red red Parking sensor failure Indicates a fault in the parking sensor system orange orange (2). Rain sensor failure Scheduled Maintenance (Service) Indicates a rain sensor failure (2). Indicates the Scheduled Maintenance deadline. orange green About your Vehicle 113

TFT Warning Description and warnings (priority level) TFT Warning Description and warnings (priority level) light light AVH system failure Generic failure Indicates an AVH system failure (0). Airbag warning lamp failure (2). orange orange Manettino failure (1). Ice hazard Electronic system failure (2). Indicates that the outside temperature is 3 °C Cruise Control (38 °F) or lower, highlighting the probable risk Indicates that the Cruise Control has been of icy road surfaces. green activated/deactivated. green Drive carefully in these conditions and slow down since tyre grip could be significantly Stop&Start on/Stop&Start system warnings reduced. Together with a special message, it indicates: orange Stop&Start system on Warning Stop&Start system active In this condition, activate the “WET” Stop&Start system not available driving mode. or temporarily deactivated. Stop&Start off Parking brake on Indicates that the Stop&Start system has been Indicates that the parking brake is applied orange deactivated. red Stop&Start failure Gearbox failure Indicates a failure in the Stop&Start system (1). red Indicates a gearbox failure (1). orange red Contact the Ferrari Service Network. Stop&Start failure Indicates a failure in the Stop&Start system (0). red 114 About your Vehicle

Electronic rev counter Engine RPM LED on steering wheel (optional) The electronic rev counter indicates the engine RPM. The numbers The five LEDs on the steering wheel rim (available on request) on the dial multiplied by 1000 correspond to the engine RPM in light up in sequence and inform the driver that the maximum one minute. engine RPM has been reached for gearshifting. When 5500 RPM is Avoid engine speed rates in the red sector. reached, the first LED comes on; the others come on in sequence when 6250, 7000, 7750 and 8420 RPM are reached. There is a space to the bottom right of the rev counter for the display which gives information on dual clutch transmission (DCT). The LEDs on the steering wheel can be deactivated using the MENU screen page on the left TFT display (see page 90): call up the MENU screen page, select the items “Car setup” and “RPM on Important note steer” and then select OFF. To reactivate the function, select ON. If the rev counter has a white or yellow background, backlighting is not activated in daytime conditions (i.e. with 3 the running lights off or with the running lights on but with the twilight sensor detecting daytime conditions) to improve visibility of the gauge. About your Vehicle 115

Gearbox display Gear engaged The gearbox display shows the number or letter indicating the The display which gives information on dual clutch transmission engaged gear in the centre. (DCT) is found to the bottom right of the rev counter; with the ignition key in position II, it displays the following information: N Neutral - Gear engaged; R Reverse - Indication of “Automatic gearbox” mode; 1 1st gear - Indication of “Auto easy exit” mode; 2 2nd gear - Indication of gearbox in “Parking” mode; 3 3rd gear - Indication of Launch Control activated; 4 etc. - Indication of AVH system activated. When the key is turned to off, the display remains on for at least 3 seconds and displays the engaged gear. If the control panel reads N (Neutral), the letter N is displayed and a buzzer will sound. 116 About your Vehicle

Indication of “Automatic gearbox” mode Indication of Launch Control activated When the gearbox is used in “automatic” mode (see page 150), the When the gearbox is used in “manual” mode and the Launch word “auto” appears in the bottom of the gearbox display together Control function is requested by pressing the special button on with the number or letter indicating the engaged gear. the centre console (see page 165), the word “launch” appears in the bottom of the gearbox display. The word remains while the Indication of “Auto easy exit” mode function is activated. When the gearbox is used in “Auto easy exit” mode (see page 150), the word “auto” appears in the bottom of the display together with Indication of AVH system activated a small “arrow” pointing downwards on the left. In certain circumstances, when the AVH system is activated (see page 163), the word “HOLD” appears in the top of the gearbox Indication of gearbox in “Parking” mode When the gearbox is in “Parking” mode, i.e. the Park Lock gearbox display. 3 locking device is activated (see page 164), the letter “P” appears in the centre of the gearbox display. About your Vehicle 117

Right TFT display “Speedometer” screen page The “Speedometer” screen page indicates the speed by displaying a Located on the instrument panel, it performs the following virtual analogue speedometer. functions: - it displays the speedometer “Digital speed” screen page - it displays infotainment system information The “Digital speed” screen page indicates the speed in digital form. - it displays the “Rear Parking Camera” and “Dual View Camera” (optional) screen pages Important note The driver can interact with the system by selecting the The speedometer is always displayed on the instrument panel: if configuration and setting the parameters using the controls on the Infotainment System information is displayed full screen on the dashboard to the right of the steering wheel. right TFT display, the virtual speedometer is displayed on the left TFT display. Holding button A down switches the infotainment system on and off. Holding button B down allows you to select whether to display infotainment system information or display the speedometer. A B 118 About your Vehicle

Time display “Rear Parking Camera” screen page (optional) By selecting the special item on the MENU screen page of the left If the vehicle has a rear parking camera (optional), the “Rear TFT display, you can activate/deactivate the time display in the top Parking Camera” screen page is automatically displayed on the right right of the “Speedometer” and “Digital speed” screen page. The TFT display when reverse gear is engaged. This screen page, which time is displayed approximately 10 seconds after key-on. continues to be displayed until reverse gear is disengaged, shows the field of vision of the camera mounted on the rear bumper and helps the driver when parking. The image is integrated with static green, yellow and red grids that indicate the distance of the obstacles that come into the camera's field of vision: the area inside the red grid covers approximately 0 to 60 cm (0-24 in.), the yellow grid 60 to 130 cm (24-51 in.) and the green grid 130 to 190 cm (51-75 in.). 3 126 About your Vehicle 119

“Dual View Camera” (optional) screen page The front camera images are not displayed if the vehicle exceeds If the vehicle has a “Dual View Camera” system consisting of 12 km/h (7 mph). another camera mounted in the front bumper in addition to the When reverse gear is engaged, the “Rear Parking Camera” view rear parking camera, the following views are displayed on the right is automatically displayed on the right TFT display. With reverse TFT display: gear engaged, press button C to switch between the two rear views - central front view with wide-angle lens available. - front side angle view To display the speedometer again, hold down button C or disengage reverse gear if it is engaged. and, with only reverse gear engaged: - rear view with grids (“Rear Parking Camera”) - rear view with wide-angle lens. The view can be selected by pressing button C on the dashboard: if the speedometer is displayed on the right TFT display, quickly press button C to display the central front view. Press the button again to switch between the two front views available. C 120 About your Vehicle

Passenger display (optional) Hold down the DISP button A to switch the passenger display on and off. Quickly press button A to switch from one screen to The passenger display B (available on request) has been designed another. to allow the front passenger to participate more in trips and provides access to a number of vehicle parameters which are normally only available to the driver. The passenger display shows information displayed on the following screens on the instrument panel: - Performance: engaged gear, RPM, speed - TRIP A: distance travelled, travel time, average and maximum speed - TRIP B (if activated): 3 distance travelled, travel time, average and maximum speed - Manettino status: Manettino position and vehicle parameter status B A About your Vehicle 121

Infotainment system Overview of dashboard controls Infotainment System information is displayed on the TFT display Button Press and quick release Press and hold down on the right of the instrument panel. (word at the top) (word at the bottom) To manage the system, use the controls on the dashboard to the A Calls up the MAIN screen Turns the Infotainment right of the steering wheel (right satellite pod). page System on/off B Goes back to the previous Displays the virtual level speedometer C Calls up the context menu Calls up the Infotainment System setup menu The joystick D can be rotated to scroll list items, held down to select an item, or moved up/down/right/left to move between system functions. Control E can be rotated to adjust volume; press to activate MUTE. C A B D E 122 About your Vehicle

MAIN screen page Press and hold down button B to display full screen Infotainment System information or the virtual speedometer. The main screen page, which can be accessed at any time by pressing button A MAIN, displays the 4 system functions: NAVI When the virtual speedometer is displayed on the right TFT display, (navigation system), MEDIA (CD/DVD, USB, iPod, Bluetooth), the Infotainment System functions are active: information (for RADIO and PHONE (telephone). example about the navigation system) is displayed in minimised form in the bottom part of the display, as shown in the example To access the functions, move the joystick D up (NAVI), right below. (MEDIA), left (RADIO) or down (PHONE). Press and release button C to access the relative context menu, from any system area. Press and hold down button C to call up the general system setup menu. 3 About your Vehicle 123

Navigation: how to get to your destination How to select a MEDIA source With the NAVI function enabled, rotate the joystick to select With the MEDIA function enabled, you can select four sources, “Destination entry” and press the joystick to confirm. In the screen in the top left of the display: DISC (CD or DVD, optional), USB page, select “Address”. Rotate and then press the joystick, to select: (external USB device), iPod (external Apple iPod), or Bluetooth the road/street, town/city, postcode, country. (streaming audio). Sources are only displayed when effectively Rotate or move the joystick then press down to select the letters available - i.e. after inserting a disc, connecting an external displayed. audio device to the USB connector in the centre console glove compartment - under the armrest - or connecting to a device via Then select “GO” to calculate the route. Press button B BACK to go Bluetooth (see page 126). back to the previous level, at any time. To switch from one source to another, move the joystick right or left. How to display the route map Move the joystick D left, to switch from displaying the navigator functions list (NAV mode) to displaying the map/route (MAP); move the joystick right to switch from the map to the functions list. When the map is displayed, rotate the joystick to zoom in/out. NAV MAP 01:30 DISC iPOD 01:30 Destination Entry Artist name Guide Me Home Back Where Am I Now? Song title Navigation Setting Pop By Genre 1:06 Song 12/163 124 About your Vehicle

Disc mode (DISC) Audio track playback The optional CD/DVD reader is installed on the rear shelf between While playing a song, press the joystick to display a button row the two rear seats. for the following functions: Play or Pause / Stop / REW / Skip - / Skip + / FF. The button row will disappear after a set timeout, or if you press the button B BACK. Warning The player only accepts 12 cm (4 3/4 inch) discs. The use of different-sized discs may damage the player mechanism. 3 DISC iPOD Katie Melua Nine Million Bicycles 02:56 Track 4 of 315 TA FM ANTENNE3 About your Vehicle 125

USB and iPod mode Listening to a RADIO station In USB mode, you can play audio files stored on external devices In RADIO mode, four different frequency bands are selectable at (e.g. USB keys). These devices can be connected to the system by the top left of the right hand TFT display: FM, MW, LW and DAB the USB connector G located in the glove compartment under the digital radio. To switch from one band to another, move the joystick armrest of the centre console. right or left. Using the USB connector, you can also play audio files from iPod® Rotate the joystick to display stored radio stations (preset): press and iPhone® devices, using the USB cable supplied with the device. the joystick to select the station. While listening to a radio station, press the joystick and release to Bluetooth mode (audio streaming) display a radio tuner button row (in the figure): Mute or Unmute / The audio files on mobile telephones paired via Bluetooth can be Seek - / Fine Tune - / Fine Tune + / Seek +. The button row will played by the system in audio streaming. For further information disappear after a set timeout, or if you press the button B BACK. on pairing a mobile phone to the infotainment system, see page 127. Playing tracks is the same as for other external devices connected via USB. FM MW LW DAB 01:30 Radio Classica 101.1 MHz Classic Preset 2 Listening to * Radio Classica G * Your favourite station* 126 About your Vehicle

Storing a radio station Pairing a telephone and making a call To store a radio station, find the frequency of the station, then The PHONE function has two modes, in the top left of the display: press and hold down the joystick D. A preset list (in the figure) will Phone and Bluetooth. To switch from one mode to another, move appear on the right TFT display: move the joystick to where you the joystick right or left. want to store the radio station and press to confirm. To use your telephone, it must be paired to the system by Bluetooth: move the joystick right to select Bluetooth mode, then select “Pair new telephone”. At this point, rotate or move and then press the joystick to enter a 4-digit code (pairing PIN) on the displayed keyboard (in the figure), then select OK. The system will ask you to pair your mobile telephone: search for Bluetooth devices, select “Ferrari”, then enter the PIN. 3 A confirmation message will be displayed. FM Pair New Phone 01:30 1 92.5 MHZ 1111_ 2 101.1 MHZ 1 2 3 4 5 6 7 8 3 103.5 MHZ 9 0 4 102.7 MHZ 5 Del OK 6 insert PIN Select 1/6 About your Vehicle 127

128 About your Vehicle

Infotainment System controls on the steering wheel Buttons A and B for volume control and button VR/TEL C are on the left-hand steering wheel spoke: press button A to increase the As well as using the commands on the dashboard to the right of volume and press button B to decrease it. Hold down button B to the steering wheel, the infotainment system can be controlled using mute the volume (MUTE function). To deactivate volume muting, buttons behind the steering wheel, as shown by the arrows in the press button A. figure. Button C is used to activate the voice commands; if the voice recognition function is already activated, it can be deactivated by quickly pressing button C. If there is an incoming call, quickly press button C to accept it or hold it down to refuse it. The SCAN + D and SCAN - E buttons are on the right-hand steering wheel spoke. They are used to scan the radio stations (if RADIO mode is activated) or go to the next or previous track (if MEDIA mode is activated). The SOURCE F button lets you select 3 available sources (MW, LW, FM, DAB, AHA, and DISC, USB, iPod or Bluetooth). A D F C E B About your Vehicle 129

Cruise Control Activating the device To activate the device, hold down control A for at least 2 seconds. The Cruise Control is an electronic device designed to help the driver drive at a constant speed of between 50 km/h and 220 km/h When Cruise Control is activated, a warning lamp lights on the (31-137 mph) without having to keep the accelerator pedal pressed. instrument panel (see page 114), and the message “Cruise Control ON”, together with the specific symbol, are shown for 5 seconds on the left hand TFT display. Important note The device cannot be activated when reverse or 1st gear are We recommend only using the device on long, dry stretches of engaged. road requiring few gear changes (e.g. motorways). When going down slopes with the device on, the vehicle speed may Do not use the device for city driving. be slightly higher than the memorised speed. Memorising the speed Important note Proceed as follows: PIT SPEED is a term taken from the motor sports world used by - with the device activated, bring the vehicle to the desired speed Ferrari to indicate the speed memorised using the device and by pressing the accelerator pedal; does not endorse inappropriate behaviour on the road which - turn control A clockwise (+) for at least 3 seconds and then does not comply with Traffic Regulations. release it: the speed of the vehicle is memorised and you can release the accelerator pedal. If necessary, you can accelerate by pressing the accelerator pedal: when the pedal is released, the vehicle will return to the previously memorised speed. A Resetting the memorised speed If the device has been turned off by pressing the brake pedal, the memorised speed can be reset as follows: - gradually accelerate until the vehicle reaches a speed which is close to the memorised speed; - quickly press control A. 130 About your Vehicle

Increasing the memorised speed This can be done in two ways: by pressing the accelerator and Warning memorising the new speed reached or by turning control A If the Cruise Control is malfunctioning or faulty, deactivate the clockwise (+). device and contact the Ferrari Service Network. One turn of the control corresponds to an increase in speed of about 2 km/h (1.2 mph); if the control is kept turned on the other hand, the speed continually increases. Reducing the memorised speed This can be done in two ways: by deactivating the device and then memorising the new speed or by turning control A counterclockwise (-). One turn of the control corresponds to a decrease in speed of 3 about 2 km/h (1.2 mph); if the control is kept turned on the other hand, the speed continually decreases. Deactivating the device Hold down control A for at least 2 seconds or turn the ignition key to position 0. The device is also automatically deactivated by pressing the brake pedal. When it is deactivated, the warning light on the instrument panel goes out and a “Cruise Control OFF” message accompanied by a special symbol appears on the left TFT display for 5 seconds. Warning While driving with the device activated, do not put the vehicle into “N” (neutral). About your Vehicle 131

Controls on the steering wheel Driving mode control switch “Manettino” The driver can select the desired driving mode by using the “Manettino” B. Start button The driving mode selected does not exempt the driver from Press the ENGINE START button A to start the engine. complying with the rules of safe driving. When the engine has started, release the ENGINE START button. Do not hold the ENGINE START button down for a long time. Important note For more information on starting the engine, see page 146. In the event of failure of one of the onboard systems, indicated by the specific symbol on the left hand TFT display (see page 114), the “Manettino” enters recovery mode, but still allows the vehicle to be driven. In these cases, contact the Ferrari Service Network. A B 132 About your Vehicle

Driving modes that can be selected with “Manettino” Warning WET mode This is the maximum safety driving mode. Recommended in low In low- to medium-grip conditions (e.g. wet, icy, sandy roads), grip conditions. activate the WET driving mode and do not deactivate the ESC. SPORT mode This is the ideal setting for vehicle performance recommended for Important note everyday driving in medium- to high-grip conditions. For further information on the driving modes that can be RACE mode selected, refer to the paragraph “Driving using the driving mode This mode offers maximum performance and stability in high grip control switch” on page 156. conditions and is particularly suitable when using the vehicle on track. 3 Warning The vehicle, which has been designed and produced for road use, should only be used occasionally on race tracks. CT OFF mode When this mode is selected, the F1-Trac traction control system is disabled whereas stability control remains active. This mode is used on the race track in high grip conditions. ESC OFF mode This mode allows the driver complete freedom and control of the vehicle for track use in high-grip conditions. No electronic system other than the E-Diff controls vehicle stability. About your Vehicle 133

Suspension damping delink button Horn control By pressing button C on the left of the steering wheel, the driver The horn sounds when you press on the horn symbol on the can choose to separate the suspension damping control from the steering wheel rim. logic of the “Manettino” driving mode control switch. For further information, see page 160. C 134 About your Vehicle

“UP” shift paddle Windscreen washer/wiper stalk Pull the right-hand UP paddle towards the steering wheel to shift gears up. Important note The windscreen wipers and washer only work when the ignition “DOWN” shift paddle key is in position II. Pull the left-hand DOWN paddle towards the steering wheel to shift gears down. The windscreen wipers and washer are operated using lever A on the steering wheel: the lever must be pressed towards the dashboard or pulled back according to the function you require. The windscreen wipers have 4 different speeds: OFF Windscreen wipers stationary. 3 AUTO The rain sensor adjusts the windscreen wiper timing to the intensity of the rain. 1 Slow continuous operation. 2 Fast continuous operation. DOWN UP A About your Vehicle 135

With the wipers stationary (OFF), quickly pressing lever A towards the dashboard activates the windscreen wipers in AUTO speed. Important note With the wipers on, quickly pressing the lever towards the Windscreen wiper operating is always guaranteed even if dashboard increases windscreen wiper speed (from AUTO to 1, there is an electronic system failure. If there is a failure, the from 1 to 2). windscreen wipers can be activated by pressing lever A and With the wipers set to AUTO or OFF, holding the lever towards the deactivated by pulling it back. dashboard activates maximum speed (2). With speed 1 or 2, on the If there is a particularly serious failure, operating may not be other hand, the windscreen wipers stop. automatically maintained: if this is the case, the windscreen With the wipers on, quickly pulling lever A back decreases wipers can be kept activated by holding down lever A. windscreen wipers speed (from 2 to 1, from 1 to AUTO, from AUTO to OFF). With the wipers stationary, quickly pulling the lever back activates Windscreen washer fast temporary operating of the wipers (antipanic wiping). To activate the windscreen washer, keep lever A pulled. When the The windscreen wiper speed is indicated in the top of the left TFT lever is released, the windscreen wiper returns to the preset speed. display as shown in the figure below. Warning Do not start the windscreen washer during the cold months until the windscreen has warmed up. If it has not warmed up, the liquid could freeze on the glass and interfere with visibility. A Headlight washer The headlight washer is activated automatically when the windscreen washer is operated and the low beams are on. The headlight washer and windscreen washer share the same fluid tank and a low fluid level is indicated by the relative symbol on the left TFT display. 136 About your Vehicle

Rain sensor Rain sensor failure The rain sensor automatically adjusts the windscreen wiper timing If there is a rain sensor failure, indicated by a special symbol on to the intensity of the rain. The system is activated by moving the the left TFT display (see page 113) while the windscreen wiper windscreen wiper to AUTO. is set to AUTO, the wipers will be set to intermittent operation When operating automatically, the wiper speed ranges from a with one wipe every 1 second approximately. If this is the case, we minimum intermittent setting (one wipe every 5 seconds approx.) recommend that you deactivate the rain sensor and turn on the when the windscreen is damp to fast continuous operation in heavy wipers, if necessary, in continuous mode. rain. Important note Important note If this occurs, contact the Ferrari Service Network as soon as The rain sensor function is deactivated by turning the ignition key to position 0 and leaving the windscreen wiper in position possible. 3 AUTO. To reactivate the system at the next key-on, set the wipers to AUTO by quickly pressing the lever A towards the dashboard. Warning Before cleaning the front windscreen (for example in service stations) make sure the rain sensor is deactivated or that the key is in position 0. The rain sensor must be deactivated also when washing the vehicle by hand or in automatic car washes. In case of ice or snow on the front windscreen, do not activate the rain sensor to avoid damaging the wiper motor and/or blades. About your Vehicle 137

Lighting High beams To turn on the high beams when the light switch A is set to , The external lights and turn indicators only work when the ignition push lever B on the steering wheel towards the dashboard. key is in position II. When the high beams are on, the relative warning light on the The external lights can be switched on and off manually or instrument panel comes on. automatically, depending on the ambient light. Then push lever B towards the dashboard or pull it back to turn off the high beams and turn on the low beams. Light switch The switch A, on the dashboard to the left of the steering wheel, Flashing the headlights can be set to four different positions: The headlights can be flashed by pulling back the left-hand lever B. 0 Lights off Flashing also occurs with lights off if the ignition key is set to II. Low beams on (*) The high beams are used for flashing. Parking lights AUT Automatic operation of the external lights according to ambient light. (*) The relative warning light on the instrument panel comes on. B A 138 About your Vehicle

Important note Important note Follow the Road Regulations of the country you are travelling in The high beams can only be activated manually by pushing the for using the high beams. left-hand lever B towards the dashboard. Important note Parking lights The parking lights work only with the ignition key in position 0 or If the high beam control is activated, the high beams will with the key removed. turn on every time the lights are activated automatically. We recommend therefore that you turn them off every time the They are activated by turning the light switch A to position . When the parking lights are on, the warning light on the instrument panel. illuminates twilight sensor deactivates the external lights. 3 When the parking lights are on, press and hold one of the two turn Warning indicator buttons C on the steering wheel (see page 138) for more If there is fog during the day, the running lights and low beams than 0.5 seconds to turn on the single-side parking lights on the will not be turned on automatically. The driver must always be corresponding side; press the same turn indicator again for more ready to turn on the lights manually and also the rear fog lights, than 0.5 seconds to go back to full parking lights. if necessary. When the partial parking lights are on (on only one side of the vehicle), the running light warning light turns off whereas the vehicle symbol indicating which parking light is on (left or right) is Important note displayed on the left TFT display for 10 seconds. After automatic activation of the external lights, it will always When the light switch A is turned to AUT and the ignition key is in be possible to turn on the rear fog lights manually. When position II, the running lights, low beams and number plate lights the external lights are deactivated automatically, the rear fog turn on and off automatically according to the ambient light. lights are also turned off (if active) automatically. Therefore, if necessary, the driver will have to turn on the rear fog lights manually upon the next automatic activation. About your Vehicle 139

Day lights Warning The LEDs on the headlights serve as front turn indicators and day The driver is always responsible for turning on the external lights. To activate or deactivate the day running lights, call up the lights, depending on the ambient light and in compliance with MENU screen page on the left TFT display, select the items “Car the regulations in force in the country of use. The automatic setup”, “Day lights” and select ON to activate the function and OFF system for turning on and off the external lights must be to deactivate it. considered an aid for the driver. If necessary, turn the lights on and off manually. Turn indicators Quickly press the left indicator or right indicator button C on the steering wheel to switch on the relevant turn indicator. Twilight sensor The relative warning light or on the instrument panel The twilight sensor is comprised of a global sensor which measures comes on. the ambient light upwards. The turn indicator goes off when the steering wheel is realigned. Sensor sensitivity can be set to three levels: call up the MENU screen page, select the items “Car setup” and “Light sensor” and Holding down one of the two C buttons (for more than use the UP and DOWN buttons to select the desired level. 0.3 seconds) temporarily switches on the relevant turn indicator: it is switched off after 3 flashes (“lane change” function). In the event of sensor failure, the system switches on the low beams and running lights, regardless of the daylight conditions; a failure message will appear on the instrument panel display. The failure indication will be displayed as long as the light switch is turned to AUT. If this occurs, we recommend that you deactivate the automatic system and turn on the external lights manually if necessary. Important note If this occurs, contact the Ferrari Service Network. C C 140 About your Vehicle

Rear fog lights Hazard warning lights The rear fog lights are turned on only if the high beams or low Press button F to turn on the hazard warning lights. All the turn beams are on when button D is pressed; the relevant warning indicators will start blinking intermittently; these lights will operate light E on the instrument panel comes on to indicate that they have with the ignition key in any position. been turned on. When the hazard warning lights are on, the relative warning lights on the instrument panel and the button flash. Important note To turn them off, press the button again. Use the rear fog lights only in poor visibility conditions. “Auto Hazard” function The “Auto Hazard” function automatically switches on the hazard warning lights in the event of sharp braking. To activate or deactivate the function, call up the MENU screen 3 page, select the items “Car setup”, “Auto Hazard” and select either “ON” or “OFF”. F E D About your Vehicle 141

“Follow me home” function AFS2 adaptive headlights (optional) With the “Follow me home” function, the low beams stay lit for a The AFS2 adaptive headlight system (available on request) enables preset period of time once the engine has been turned off and light synchronous movement of the left and right front beams (high up the area around the vehicle to help the driver and passengers and low) and has been designed to illuminate the road better and see their way in the dark. reduce areas of shadow in the vehicle's trajectory. To activate this function manually, push the high beam/flash stalk B The headlights' swivel angle, which ranges from 8° inwards and 15° (see page 138) with the ignition key turned to 0 or removed, within outwards, is defined by the steering angle. 3 minutes of switching off the engine. This time is reduced to The AFS2 system also uses a “Dynamic Levelling” device that 30 seconds if the driver side door is opened. Each time lever B is directs the light beam vertically when accelerating and braking by pressed, the period of time that the low beams remain on increases moving the headlights up to 1.9° upwards when braking and up to by 30 seconds up to a maximum of 210 seconds. 1° downwards when accelerating. Each time lever B is pressed, the message “Follow me” appears on The adaptive headlight system deactivates its corrective action the left TFT display followed by the preset period of time that the when driving round bends at low speed. low beams remain on. 142 About your Vehicle

Dome light Roof panel controls When the doors are closed, the dome light D on the roof can be turned on or off using the switch E. Door lock/unlock Switches F and G turn the driver-side and passenger-side spotlights Both doors can be locked by activating/deactivating the “LOCK/ on and off. UNLOCK” H button. For further information, see page 78. The dome light activates automatically in the following conditions: - when a door is opened, for approx. 3 minutes Deactivating the anti-lift volumetric alarm - when all the doors are closed and the key is in position 0, for Press button L to deactivate the anti-lift volumetric alarm system. approximately 10 seconds For further information, see page 18. - when the key is removed, for approx. 10 seconds - when the doors are unlocked, for approx. 10 seconds Front parking sensors 3 - when the inertia switch is activated, for approx. 15 minutes. Press button M to activate/deactivate the front parking sensors. The dome light deactivates automatically in the following conditions: When the front parking sensors are activated, the light on the button comes on. - after the preset activation time expires - when the doors are closed and the key is in position II - when the doors are locked - when the inertia switch is reactivated. M F E G H L D About your Vehicle 143

Driving the vehicle Before a trip Running-in Preliminary checks The latest manufacturing techniques have allowed us to achieve Check the following at regular intervals and always before long high precision and accuracy levels in the construction and assembly trips: of components. Nonetheless, the vehicle movable parts undergo a - tyre pressure and condition settling process, basically during the first hours of operation. - levels of fluids and lubricants - condition of the windscreen wiper blades Engine and transmission - proper functioning of the warning lights and external lights. Avoid exceeding 5,000 RPM for the first 1,000 km (620 mi). After starting, do not exceed 4,000 RPM until the engine has warmed up (oil temperature: 65-70 °C / 149-158 °F). Important note Do not let the engine run at a constantly high speed for a In any case, it is advisable to perform these checks at least every prolonged time. 1000 km (620 mi) and always comply with the maintenance schedule. Warning It is also advisable to: BEFORE YOU DRIVE - clean the glass covers of the external lights and all the glass Check that the seat belts are fastened surfaces Check that the doors are closed - properly adjust the mirrors, steering wheel, seats and seat belts. Check that the seat is properly adjusted Check rear-view mirror adjustment Warning (central and sides). Use unleaded fuel only! Using leaded fuel would permanently damage the catalytic converters. For specifications and quantities of lubricants and fluids, refer to the “Refilling” table on page 35. 144 About your Vehicle

Starting and driving the vehicle Important note System start-up BEFORE YOU DRIVE After turning the ignition key to position II (key-on), both TFT If the warning light A does not turn off after diagnosis, displays are activated on the instrument panel and system diagnosis indicating a fault in the gearbox also shown by the symbol and is performed. During diagnosis, which lasts 5 seconds, a check is special message on the left TFT display (see page 114), contact performed on the warning lights on the panel and the presence of the Ferrari Service Network. any faults is checked. If diagnosis detects any errors, they are only displayed once the 5 seconds required for the check have elapsed. The cases listed below are an exception and errors are displayed as soon as the key is turned to on, even during diagnosis: 3 - Low engine oil pressure (see page 110) - Inertia switch triggered (see page 109) - Semi-automatic gearbox safety warnings - Deactivation of EPB warning (see page 162). If the next scheduled maintenance deadline is approaching, each time the key is turned to on, information on scheduled maintenance is automatically displayed after diagnosis. For further information, refer to the “Maintenance Schedule” paragraph on page 234. Finally, each time the key is turned to on, the message for activation of the alarm when an intrusion has been attempted (see page 19) is also displayed (after diagnosis). Once the system check has been completed, the gearbox display A is activated and the letter “P” (Parking) or “N” (Neutral) will be displayed. About your Vehicle 145

Starting the engine Important note Before starting the engine, make sure that the alarm system and all The vehicle is equipped with an electro-hydraulically controlled electrical devices with high power absorption are turned off. gearbox system operated by means of paddles on the steering • Make sure that the electric parking brake is applied and that the wheel. doors are closed. The default setting for the DCT gearbox is always “Automatic” • Hold the brake pedal down when starting the engine. mode (see page 150). Every time the vehicle is started, the DCT gearbox is in “Auto Warning easy exit” mode (see page 150) unless the vehicle was in “Automatic” mode when the engine was turned off. Do not press the accelerator pedal. To exit the “Auto easy exit” mode operate the UP and DOWN paddles (while the vehicle is moving) or press the AUTO button • Turn the ignition key to position II and wait for the gearbox on the centre console. display to come on. • Press the ENGINE START button (see page 132) and release it as soon as the engine starts. Important note Do not hold the ENGINE START button pressed down for a long Immediately release the UP and DOWN paddles or button R time. after the gearbox display shows that the gear has been engaged; If the engine does not start, turn the key back to position 0 and a prolonged manoeuvre would cause the gearbox failure wait for the gear display to go off before retrying. warning light to turn on (see page 114) and triggering of the buzzer. Warning Hold the brake pedal down while starting the engine. Important note None of the gears can be engaged if the engine compartment lid is open or not properly closed. When the vehicle is stationary, with the driver-side door open or not properly closed and the brake pedal released, the system disengages the gear engaged after approximately two seconds. 146 About your Vehicle

If the engine fails to start after several attempts, check for one of the following causes: Warning • insufficient speed of the starter motor (flat battery) If the UP and DOWN paddles are not working, the message • ignition device faulty “Depress brake pedal and press LAUNCH to engage gear” will • electrical contacts faulty appear on the left TFT display; you can therefore engage the gear by pressing the LAUNCH button on the centre console (see • fuel pump fuses blown. page 164) and the brake pedal. Warming up the engine In these cases, the “Launch Control” function is not available. Do not run the engine at high speed until the engine oil temperature If the engaged gear was R, the LAUNCH button must be pressed has reached at least 65-70 °C (149-158 °F), approximately. twice to engage 1st gear. Starting the vehicle Important note 3 With the engine started, the vehicle stationary and the brake pedal pressed, pull the right-hand UP paddle towards the steering wheel When reverse is selected, an acoustic safety signal beeps to engage 1st gear. intermittently as long as “R” is engaged. Release the brake pedal and press the accelerator to start off. With the engine running and the vehicle stationary, you can change If the system automatically selects 2nd gear when attempting to directly from 1st or 2nd gear to “R” (reverse) by pressing R on the shift from “R” to 1st gear, this indicates that 1st gear has jammed. centre console and from reverse to 1st by moving the UP paddle. Therefore, this is not a malfunction, as it falls within the system operating logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has R jammed. During prolonged stops with the engine running, it is advisable to keep the gearshift in “N”. Important note If you allow the vehicle to move forward in “N”, when “UP” or “DOWN” is requested, a gear will be engaged that corresponds to the speed of the vehicle. About your Vehicle 147

UP-shifting In any event, it is advisable to: Use the right-hand UP paddle without releasing the accelerator • Shift gears without releasing the accelerator pedal if pressed. pedal. • If DOWN-shifting is requested to start overtaking which requires An UP-shift request is not accepted when engagement of the quick acceleration, press the accelerator pedal just before using requested gear forces the engine to underrev or if an UP-shift is the paddle. already in progress because of engine overrevving. • Wait until gearshifting has been completed before requesting the In any event, it is advisable to: next shift, avoiding a rapid sequence of multiple requests. • Shift gears without releasing the accelerator pedal if pressed. • Wait until gearshifting has been completed before requesting the DOWN-shifting due to underrevving next shift, avoiding a rapid sequence of multiple requests. • The system shifts down “automatically” if the engine goes below a minimum number of revs (1250 RPM). “UP” for overrevving • The DOWN-shift request from the paddle is ignored if The system “automatically” engages a higher gear if the accelerator gearshifting is already in progress due to engine underrevving. pedal is pressed and the engine approaches the “runaway speed rate” (overrevving). Sequential downshifting During deceleration, with the brake pedal pressed and the ABS Important note system disabled, sequential downshifting can be performed by holding the left-hand “DOWN” paddle down. This will not occur when the system is in “RACE”, “CT OFF” and “ESC OFF” driving modes. The sequential gearshifting request is accepted until the second gear is engaged. This system is only activated when the “Manettino” is set to RACE, CT OFF or ESC OFF. DOWN-shifting Use the left-hand DOWN paddle without releasing the accelerator pedal. A DOWN-shift request is not accepted if engagement of the requested gear forces the engine beyond a certain RPM, depending on the gear requested, or if a DOWN-shift is already in progress because of engine underrevving. 148 About your Vehicle

“N” (Neutral) request With the engine running, pull both UP and DOWN paddles Warning towards the steering wheel at the same time without pressing the Never leave the vehicle with the gearbox in “N”. Always make brake pedal to request neutral “N”. sure that the letter “P” (Parking) appears on the gearbox display. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN”- shift is requested, the system will engage the gear most suited to the speed of the vehicle. Warning Never leave the vehicle with the engine running. Stopping the vehicle When the vehicle stops, the system automatically engages 1st gear unless Neutral has already been requested. When the vehicle is stationary and the engine is running, hold the Important note If the vehicle is not in Parking mode (the letter “P” must be 3 brake pedal down until ready to move off again. displayed on the gearbox display), the key cannot be removed. Switching off the engine For information on the Park Lock, see page 164. The engine can be switched off with the gearbox either in “N” or with a gear engaged. After turning the ignition key from position II to position 0, the gearbox display will remain on for a few more seconds to display the gear engaged. If the gearbox is in “N” a buzzer will sound. Before switching off, the letter “P” is displayed on the gearbox display to inform the driver that the Park Lock has been activated. About your Vehicle 149

“Automatic gearbox” mode “Auto easy exit” mode The “Automatic gearbox” mode is enabled/disabled by pressing the Every time the vehicle is started, the gearbox starts in “Auto easy AUTO C button on the centre console. When the “Automatic” mode exit” mode unless it was in “Automatic” mode when the engine was is enabled, the word “auto” appears on the gearbox display. To exit turned off. In this case, it remains in “Automatic” mode the next the “Automatic” mode, you must press the AUTO button until the time the engine is started. word “auto” on the gearbox display disappears. Activation is confirmed by the message “auto” and a downward When the “Automatic Gearbox” mode is enabled, the system will arrow in the gearbox display. automatically UP-shift and DOWN-shift according to vehicle speed, In this mode, the system will automatically UP-shift and DOWN- engine revs and the torque/power request of the driver. shift according to vehicle speed, engine revs and the torque/power When you are in “Automatic” mode, you can however manually request of the driver. shift gears using the UP and DOWN paddles. The system remains To exit the “Auto easy exit” mode and go to “Manual” mode, in “Automatic” mode: this is indicated by the word “auto” that operate the UP or DOWN paddle (while the vehicle is moving) or remains on the gearbox display in flashing mode when the paddles press the AUTO button on the centre console. are used. If the “Automatic” gearbox mode is then requested by pressing the When the vehicle is stationary, a “N”, 1st gear or “R”request will not AUTO button, the system will apply all the characteristics of the result in a change from “Automatic” to “Manual”. “Automatic” gearbox mode. Push start Warning Push starting is not allowed. C 150 About your Vehicle

Safe driving While travelling For safe driving, it is essential that the driver be aware of the best - Caution is the number one rule for safe driving, which also means driving techniques suited to various circumstances. Always try to you should take other people’s behaviour into consideration. prevent dangerous situations by driving with caution. - Follow the Road Regulations in force in the country you are driving in and always respect the speed limit. Before you drive - Always make sure that the driver and passengers have their seat - Adjust the position of the seat, steering wheel and rear-view belts fastened and that all children are travelling in suitable child mirrors, in order to obtain the best driving position. seats. - Adjust the backrest so that your chest is upright and your head is - Good personal physical conditions ensure you can drive long as close to the headrest as possible. distances safely. - Ensure that nothing (e.g. mat covers, etc.) is blocking the pedals. - Check that the lights and headlights are working properly. Warning 3 - Ensure that any child restraint systems (e.g. child seats, cradles Driving under the influence of drugs, some medicines etc.) are properly fixed on the passenger seat. and alcohol is dangerous to yourself and others as well as contravening road regulations and legal norms. - Your reflexes are quicker if you eat lightly before driving: avoid heavy meals before a trip. Travelling without your seat belt fastened increases the risk of serious injury and death in the event of a collision. Always - Do not drink alcoholic drinks before and during the journey. fasten seat belts and use child seats, if present. At regular intervals, check the following: Do not travel with objects lying on the floor, especially in front - Tyre pressure and condition. of the driver’s seat: in the event of braking, these could slide - Engine oil level under the pedals, making it impossible to brake or accelerate. - Engine coolant level and system condition Additionally, ensure that any loose floor mats sit correctly. - Brake fluid level Water, ice and salt spread on icy roads may deposit on the brake - Steering fluid level discs and reduce the efficiency of the initial braking. - Windscreen washer fluid level. About your Vehicle 151

- Make regular stops to loosen up your limbs and refresh yourself, Driving in the rain and avoid driving for hours on end. Rain and wet roads can cause hazardous situations. - Keep a constant air circulation in the passenger compartment. All manoeuvres are more difficult on a wet road since tyres have - Never coast downhill with the engine off: in these conditions significantly less grip on the road. This means that the braking the engine brake, servo brake and power steering are inefficient, distances increase considerably and road-holding decreases. braking requires greater pressure on the pedal and steering will Here is some advice for driving in the rain: be harder. - Keep a greater safety distance between yourself and the other vehicles and reduce your speed. Driving at night - When it is raining very hard, visibility is also reduced. In these When you are travelling at night, follow these fundamental rules: cases, to make yourself more visible to others, turn on the low - Reduce speed, particularly on dark roads. beams even during the day. - Driving conditions are more demanding at night, so take - Drive through puddles at low speed to avoid losing control of the particular care. vehicle (“aquaplaning”): if this occurs, grip the steering wheel - If you start feeling tired or sleepy, stop immediately: to continue firmly. driving would be a risk for yourself and for others. Continue only after you have had a rest. Warning - At night, it is difficult to judge the speed of vehicles in front of If the road is wet, considerably reduce your speed to avoid you as you can only see their taillights: keep at a greater safety “aquaplaning” (when the tyre no longer touches the road distance than you would during the day. surface because the side channels of the tyre tread are not - Use the high beams only outside of urban areas and when you are capable of removing all the channelled water due to their sure that they will not disturb other drivers. particular shape or insufficient depth and a layer of water is - Turn off the high beams when you see oncoming vehicles and use placed between the road surface and the tyre. The fluid pressure the low beams. generated is so high that it supports the vehicle's weight making - Keep the lights and headlights clean. it virtually impossible for the driver to control the vehicle). - Watch out for animals crossing the road when travelling outside urban areas. 152 About your Vehicle

- Use the ventilation system to demist the windscreen Driving on mountain roads (see page 185) and avoid visibility problems. Below is some advice for driving on steep roads: - Periodically check the condition of the windscreen wiper blades. - To prevent the brakes from overheating when driving downhill, use the engine to brake by engaging a lower gear. Driving in fog - Never coast downhill or drive downhill with the engine off or Whenever possible, avoid travelling if there is thick fog. If you have in neutral, nor with the ignition key removed from the steering to drive in misty conditions, or if there is thick fog or fog banks, column. follow these rules: - Drive at a moderate speeds and do not “cut” corners. - Keep a moderate speed. - Remember that overtaking uphill is slower and requires a longer - Turn on the low beams, also during the day, and use the rear fog free stretch of road. If you are overtaken when driving uphill, light. Avoid using the high beams. ensure that the other vehicle can pass easily. 3 Warning Driving on snowy or icy roads On stretches where visibility is good, turn off the rear fog light, Below is some advice for driving in these conditions: it may be annoying for the occupants of the vehicles behind - Keep a very moderate speed. you. - Keep a safe distance from the vehicles in front of you. - Fit snow tyres approved for the vehicle. - Remember that fog makes the road damp and therefore all - Given the poor grip, use the engine brake as much as possible manoeuvres are more difficult and braking distances are longer. and avoid sudden braking. - Keep a safe distance from the vehicle in front of you. - Avoid sudden acceleration and sharp changes in direction. - As far as possible, avoid suddenly changing speed and direction. - During the winter season, even apparently dry roads can have icy - As far as possible, avoid overtaking. sections. - In the event of an emergency stop, (e.g. failures, inability to Therefore, be careful when driving along stretches of road in the proceed due to poor visibility conditions, etc.) try to free the shade as there may be icy patches. main driving lane. Then turn on the hazard warning lights and, if possible, the low beams. On approaching another vehicle, sound the horn rhythmically. About your Vehicle 153

Driving with the “ABS” braking system Power steering system The ABS system assists the driver as follows: The power steering system uses the power produced by the engine - It prevents the wheels from locking and skidding during to help the driver steer more precisely while exerting less force on emergency braking, particularly in low-grip conditions. the steering wheel. - It allows braking and changing direction at the same time. This feature is affected by the physical limits and lateral grip of the Important note tyres. Remember that power steering does not work when the engine - When the ABS is activated, you will feel a slight pulsing of the is switched off and more force is therefore needed when brake pedal during emergency braking or in low-grip conditions. steering. DO NOT release the pedal but continue to push it to give continuity to the braking action. - The ABS prevents the wheels from locking, but it does not Warning increase the physical limits of grip between the tyres and the road: Do not keep the steering wheel fully turned (locked position) to keep a safe distance from the vehicles ahead and reduce speed the right or the left for more than 15 seconds when the engine before curves. is running. This may damage the power steering system. Important note In the event of a power steering system malfunction, as indicated by the specific symbol on the left hand TFT display (see page 111), contact the Ferrari Service Network. 154 About your Vehicle

Suspension damping control Level 1 (COMFORT) Slightly more flexible setting, optimised to better absorb road This vehicle uses latest generation MagneRide™ magnetorheological unevenness and provide a better grip on wet road surfaces suspension, a system developed by Delphi and perfected by (Manettino set to WET). Ferrari for continuous automatic damping control. Level 2 (SPORT) By processing data received from the vehicle dynamics sensors and sensors that detect bodyshell movements, the ECU interprets the Slightly more rigid adjustment optimised for sports-style driving driving conditions and the road surface and immediately adjusts and for high speed (with medium-high grip), without significantly suspension response by varying the control current of each shock affecting comfort (Manettino set to SPORT). absorber. Level 3 (RACE) These sensors allow the ECU to calculate the vehicle speed, vertical Even more rigid setting optimised for use on the race track and lateral acceleration, steering angle and instantaneous pressure in the braking system, and hence to control suspension damping. (Manettino set to RACE, CT OFF, ESC OFF). 3 This system not only ensures an optimal compromise between racing-style performance (handling) and comfort, but is capable of emphasising either aspect by using the different adjustments available controlled by the “Manettino” driving mode control switch. Three different setting levels are available on this vehicle. About your Vehicle 155

Driving using the driving mode control switch SPORT mode (“Manettino”) The “SPORT” mode is the best setting for daily road use. This mode is designed to ensure stability only in medium-high grip The driving mode control switch on the steering wheel allows the conditions. Suspension damping shifts to Level 2 and gearshifting driver to use the vehicle potential in a fast and intuitive way. is more racy. The ESC system also switches to a different level There are five modes available, which correspond to the grip offering you greater driving freedom. level (from low to high) and consequently to the level of driving If “SPORT” mode is selected, it is indicated on the left TFT display assistance required (from high to none). as shown below: WET mode “WET” mode ensures stability on dry as well as on wet roads. It is therefore recommended for low grip conditions (e.g. rain) and on slippery or extremely uneven roads, but also to enhance comfort during city driving. Suspension damping is optimised to provide the best possible absorption (Level 1) and the ESC system is at its maximum level; the standard Bosch ASR system is activated instead of the F1-Trac function. If “WET” mode is selected, it is indicated on the left TFT display as shown below: 156 About your Vehicle

RACE mode The RACE mode should be used on the race track. Gearshifting Warning favours the racing style of the vehicle whereas the ESC system Use of the vehicle on race tracks: after each start, cover the shifts to Level 3 (engine power reductions are minimal) and the first straight stretch of the track (at least 500 meters / 0.3 mi) suspension becomes even stiffer (Level 3). The performance ABS at a constant speed so that the traction control system and the shifts to “Sport” level. This mode is designed to ensure stability on ABS can calculate exactly how much grip is available and the the race track in high grip conditions. diameter of the tyres (the calculation is reset every time the If “RACE” mode is selected, it is indicated on the left TFT display engine stops). as shown below: Failure to observe this rule may lead to reduced system performance. The vehicle, which has been designed and produced for road use, should only be used occasionally on race tracks. 3 About your Vehicle 157

CT OFF mode ESC OFF mode In “CT OFF” mode the F1-Trac traction control is disabled. This In “ESC OFF” mode the ESC system is disabled. No electronic mode further enhances the already racing -style behaviour of the systems other than the E-Diff control vehicle stability and the vehicle: traction control is disabled while stability control remains driver is allowed complete freedom and control of the vehicle active when a certain level of sideslip is exceeded. The gearshift for track use. This mode is used on the race track in high grip mode, suspension damping and the performance ABS setting are conditions. The gearshift mode, suspension damping and the the same as the previous position. The electronic differential has a performance ABS setting are the same as the “RACE” and “CT specific setting developed to emphasise the dynamic qualities of the OFF” modes. vehicle. Stability is not ensured. This mode is used on the race track in high grip conditions. Warning If “CT OFF” mode is selected, this is indicated on the left TFT The vehicle, which has been designed and produced for road display as shown below: use, should only be used occasionally on race tracks. Warning In low- to medium-grip conditions (e.g. wet, icy, sandy roads), activate the WET driving mode and do not deactivate the ESC. Important note When “ESC OFF” mode is selected, the Manettino lever automatically goes back to “CT OFF” mode: this occurs because each time the engine is started, the ESC system is reactivated. 158 About your Vehicle

Important note When the brake pedal is pressed, traction control is activated via the VDC system (vehicle dynamics control via the braking system). If ESC OFF mode is selected, this is indicated on the left TFT display as shown below: 3 About your Vehicle 159

Suspension damping delink button If button A has been pressed and subsequently the position of the Manettino is changed, the suspension setting follows the operating The driver may decide to separate the suspension setting from the logic dictated by the Manettino. logic of the “Manettino” driving mode control switch using the special button A on the steering wheel. Important note By pressing button A, irrespective of the position of the Manettino, the suspension setting shifts to Level 1 (COMFORT). Upon turning off and restarting the vehicle, the suspension setting depends on the position of the Manettino. Position of Suspension Button A Manettino setting pressed When the Manettino is set to SPORT, RACE, CT OFF or ESC OFF, WET COMFORT remains COMFORT shifting to the COMFORT suspension setting by pressing button A SPORT SPORT shifts to COMFORT is indicated by displaying the special symbol and “Bumpy road” message on the left TFT display for 5 seconds. RACE RACE shifts to COMFORT CT OFF RACE shifts to COMFORT ESC OFF RACE shifts to COMFORT A Bumpy road 160 About your Vehicle

After 5 seconds, next to the Manettino status in the top of the display, the suspension symbol continues to be displayed as shown in the photo below (example shows Manettino in “SPORT” mode). 3 About your Vehicle 161

EPB - Electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. Always apply the parking brake when the vehicle is parked. The parking brake can be applied and released by pulling a special lever B on the dashboard to the left of the steering wheel. With the The vehicle should be blocked. If this is not the case, please ignition key turned to II, the relative indicator on the instrument contact the Ferrari Service Network. panel (see page 114) lights up to indicate when the parking brake is engaged. Pull the lever B while holding the brake pedal depressed to release Drive Away function the parking brake. If the ignition key is turned to II, the indicator The electric parking brake (EPB) has a “Drive Away” function: extinguishes once the parking brake is completely released. when a gear is engaged and the driver presses the accelerator The electric parking brake can be used as an emergency brake pedal with the engine running and seat belt fastened, the system when the vehicle is in motion. If this is the case, the system acts on recognises the driver's intention to drive off and automatically all four wheels until button B is released by communicating with deactivates the parking brake. the ESP system which prevents locking. EPB deactivation warning If you try to deactivate the electric parking brake by moving lever B without depressing the brake pedal, the message “Depress brake pedal and deactivate EPB”, is immediately displayed on the left TFT display (even during system diagnosis, see page 145) accompanied by an acoustic signal. B 162 About your Vehicle

Autopark function “Automatic Vehicle Holding” AVH function The EPB Autopark function automatically activates the electric The electric parking brake provides optimised release when the parking brake when the engine is switched off. At each Key-on, the vehicle starts up due to its Automatic Vehicle Holding function: Autopark function is always active by default: this means that the once the engine has started, the system keeps the vehicle braked driver does not need to apply the parking brake when the engine is through intervention of the braking system rather than through the switched off. parking brake shoes. However, the function can be temporarily deactivated before switching off the engine by pressing the AUTO PARK C button: the message “PARK OFF” is displayed on the left TFT display for 5 seconds. In this case, after the engine is switched off, the parking brake must be engaged manually by pulling the lever B. To re- enable automatic EPB engagement at the next key-off, press the button C again; the message “PARK ON” is displayed on the left 3 TFT display for 5 seconds. C About your Vehicle 163

Park Lock Carwash procedure The Park Lock is a locking device built into the gearbox. The Park lock device can be electrically disabled on a temporary basis when the engine is switched off by performing the Carwash This device is used to prevent the vehicle from moving when the procedure. multi-disc clutches are open, i.e., with the engine off and/or without the hydraulic pressure required for gearbox operating. This procedure is necessary when the vehicle has to be moved with the engine off and when washing the vehicle. The device operates automatically every time the key is turned to off: if a gear is engaged when the key is turned to off, the Park Lock is immediately activated. If the gearbox is in “N” (neutral), the Warning Park Lock starts operating after a minimum preset time (needed for the Carwash procedure, see next paragraph). To inform the driver When the Park Lock device is electronically deactivated that the Park Lock has been engaged, the letter “P” is displayed on (Carwash procedure), the vehicle may move. the gearbox display. The vehicle is only kept stationary by the parking brake which The Park Lock is deactivated when the engine is running, the first must be applied. gear or “R” is requested (with the brake pedal pressed) and the engine compartment lid has been closed correctly. To perform the Carwash procedure, do the following: - with the engine running, select the first gear; - select neutral “N”; - switch off the engine; - turn the key to position II (key-on) within 3 seconds of switching off. The message “Carwash mode activation” will appear on the left TFT display. 164 About your Vehicle

Launch Control Warning “Launch Control” mode is a performance start function. Activating this function optimises vehicle acceleration from a standing start. Only use the “Launch Control” function in an appropriate context. The device, which is not available when the Manettino is set to the “WET” driving mode, transfers the necessary torque to the ground and avoids skidding of the wheels during acceleration. Important note To start the vehicle in “Launch Control” mode, do the following: The “Launch Control” function is not available in presence of: - the vehicle must be stationary - a sloping road surface, even slight - the gearbox must be in “Manual” mode - high clutch temperatures. - hold the brake pedal down and select first gear - press the LAUNCH button L on the central console: an acoustic 3 signal informs the driver that the device has been switched on and the word “launch” appears on the gearbox display - press the accelerator pedal and release the brake pedal. L About your Vehicle 165

Stop&Start system (optional) Warning On vehicles with optional HELE (High Emotion Low Emissions) technology, there is a Stop&Start system, which automatically stops Always make sure that the Stop&Start system has been the engine when the vehicle is stationary and restarts it, again deactivated before carrying out any repair and/or maintenance automatically, when the driver wants to set off again. work as indicated on the special labels in the engine compartment and underneath the vehicle. The aim of the Stop&Start function is to increase vehicle efficiency by reducing CO2 emissions especially when driving around town. Failure to comply with the above may pose a risk of serious injury to people working on the vehicle. Automatic stopping and restarting of the engine is controlled by sensors and control strategies which, while reducing the impact on vehicle flexibility and comfort to a minimum, guarantee full Warning operating of the safety systems and all the on-board systems even when the engine is switched off, without affecting climate comfort. The driver is personally responsible for leaving the key in the ignition in position II when getting out of the vehicle: the driver Warning must always turn the ignition key to position 0 before getting out of the vehicle. Never leave the vehicle without turning the ignition key to position 0. Always remember to remove the key from the ignition when you Warning get out of the vehicle! Leaving the vehicle with the ignition key in position II puts Never leave children unattended in the vehicle. those who are in the vicinity of the vehicle at serious risk if the engine starts unexpectedly. Warning Warning Make sure that the engine is switched off with the ignition key in position 0 before refuelling. Always turn the ignition key to position 0 before changing the tyres. 166 About your Vehicle

How the system works If the Stop&Start system is activated, the LED on button A comes on whereas if the system is deactivated, the LED goes off. If activated, the Stop&Start system decides when to switch off the engine and when to restart it according to the driving conditions, Deactivation of the system by pressing button A while in a stopped the climate comfort on board and the operating status of the vehicle condition (when the engine has been automatically vehicle. The system logic does not require drivers to make any switched off by the Stop&Start function) automatically restarts the change in the way they drive the vehicle. engine. Manual activation and deactivation button The driver can activate/deactivate the Stop&Start system at any time by pressing button A on the roof panel. If the system is activated, pressing button A will deactivate it: the message “Stop&Start OFF” appears for 5 seconds on the left TFT 3 display accompanied by a special symbol. Once the system has been deactivated, pressing button A again reactivates the system: the message “Stop&Start ON” appears for 5 seconds on the left TFT display accompanied by a special symbol. A Stop&Start OFF About your Vehicle 167

Automatic engine stop mode Important note The engine stops automatically when the vehicle is stationary Each time the ignition key is turned to position II (Key-on), the and the brake pedal is pressed and restarts when the brake Stop&Start system remains in the same state it was in when the pedal is released. switch was turned to position 0 (Key-off). If the function was The left TFT display informs the driver that the Stop&Start system activated at Key-off, it remains activated at the next Key-on and has been activated by displaying the message “Stop&Start active” the LED on button A will flash for a few seconds. accompanied by a special symbol. The message is displayed as long as the vehicle remains in a stop state. To interrupt the display cycle and reduce the message to an icon, press the OK button with “ESCAPE” function. Stop&Start Stop&Start ON active 168 About your Vehicle

Conditions required to activate automatic engine stop To activate the automatic engine stop while driving: Important note - the Stop&Start system must be activated by pressing the button After the first cold start, the Stop&Start system may take a few on the roof panel (LED on); minutes before it is ready. This time period allows some of the - the driver’s seat belt must be fastened. engine parameters (catalytic converter temperature, for example) to reach the values required to reduce emissions. For safety reasons and to guarantee driving comfort and correct operating of the entire vehicle, automatic engine switching-off is deactivated when: Important note - the accelerator pedal is depressed; If the engine continues to run when the vehicle is stationary - a potentially dangerous situation is identified (steep road, vehicle stationary with wheels turned, i.e. when turning at a crossroads or on a roundabout); and the brake pedal is pressed, even if the Stop&Start system appears to be activated, it means that the system has disabled automatic switching off of the engine. When this happens, no 3 - the system recognises vehicle motion in slow traffic or a parking specific signal is displayed on the instrument panel: this is to be manoeuvre (checking reverse gear engagement, time elapsed since considered normal. last stop, driving speed); - maximum air conditioning and heating system performance is requested (“low”, “max. defrost” or “rear screen demisting”); - external temperatures are very low or very high; - the gearbox is in the “N” position; - the “LIFT” system has been activated; - the DCT gearbox Park Lock has been manually released; - a failure that interferes with proper system operation. The system also constantly monitors some of the vehicle operating parameters (battery charge level, engine coolant temperature, catalytic converter temperature, clutch oil temperature, vacuum level in brake servo, climate comfort in passenger compartment) so that engine switching off can be deactivated in certain conditions to guarantee safety and vehicle operating and minimise the impact on on-board climate comfort. About your Vehicle 169

Information on automatic restarting of engine - the front “LIFT” system has been activated With the Stop&Start system activated in a stopped vehicle - rear screen demisting has been requested or the air conditioning condition, the driver can restart the engine by: and heating system set to “low” or “max. defrost”. - releasing the brake pedal The system also constantly monitors some of the vehicle operating - UP-shifting parameters (battery charge level, engine coolant temperature, catalytic converter temperature, clutch oil temperature, vacuum - engaging reverse gear level in brake servo, climate comfort in passenger compartment, - pressing the accelerator pedal. vehicle speed) so that the engine can be automatically started in certain conditions to guarantee safety and vehicle operating and Warning minimise the impact on on-board climate comfort. If the engine is switched off accidentally and not by the Stop&Start system, it must be restarted manually by the driver by pressing the ENGINE START button and reengaging the gear using the shift paddles located behind the steering wheel. This condition is indicated on the left TFT display by the message “Press ENGINE START button to restart”, accompanied by an acoustic signal. For safety reasons and to guarantee comfort when the vehicle is stationary and correct operating of the entire vehicle, the Stop&Start system also automatically restarts the engine when: - the ENGINE START button on the steering wheel has been pressed - the function has been deactivated by pressing the button located on the roof panel - the driver's seat belt has been unfastened - the driver-side door has been opened 170 About your Vehicle

Permanent deactivation of automatic restarting and manual start procedures Permanent deactivation of automatic restarting occurs when: After automatically switching off the engine using the Stop&Start - the engine compartment lid is open; system, automatic restarting requested by the driver may not always - automatic engine restarting has not been successful; be possible: this means that the vehicle systems have permanently - a failure has been detected that may interfere with operating of deactivated automatic restarting. the Stop&Start system. If this occurs, the vehicle must be restarted manually: this condition At times, depending on the seriousness of the failure, the ENGINE is indicated on the TFT display by the message “Press ENGINE START button may have to be held down for a few seconds to START button to restart”, accompanied by an acoustic signal. restart the engine: this condition is indicated on the left TFT display by the message “Press and hold ENGINE START button to Warning start”. If automatic restarting is permanently disabled, the vehicle behaves in the same way as a vehicle with no Stop&Start system: 3 to restart, the driver must perform a manual start by pressing the ENGINE START button and using the shift paddles located behind the steering wheel. Press Press and hold ENGINE ENGINE START START button button to restart to start About your Vehicle 171

System failure Precautions to be taken during maintenance work If malfunctioning, the Stop&Start system is disabled. The driver is Always turn the ignition key to position 0 before carrying out any informed of the failure by a special symbol that appears on the left repair and/or maintenance work on the vehicle. If work has to TFT display for 20 seconds accompanied by an acoustic signal and be carried out on the vehicle with the ignition key in position II, the following message which corresponds to two different alarm check that the Stop&Start has been deactivated by performing the levels: following procedure before doing any repair and/or maintenance - “Stop&Start failure” (orange symbol) work: - “Stop&Start failure. Go to dealer” (red symbol). if the ignition key is in position II, turn to position 0 then turn back to II and press the relative Stop&Start system activation/ deactivation button on the roof panel (see page 167). If the Important note message “Stop&Start ON” appears on the left TFT display when the Contact the Ferrari Service Network immediately. button is pressed, press the button again. Check that the message “Stop&Start OFF” appears on the left TFT display for 5 seconds. The button LED must be off. When the display cycle ends (20 seconds), or the OK button with “ESCAPE” function is pressed, the message disappears and the symbol is reduced to an icon. Warning NEVER work on the vehicle if the message “Stop&Start active” appears on the left TFT display. Stop&Start Stop&Start failure failure Go to dealer 172 About your Vehicle

Dome light controls (HELE system only) On vehicles with the optional HELE system, the central dome light B can be switched on or off by holding button C or D down (for more than 0.8 seconds). The driver-side spotlight and the passenger-side spotlight can be switched on and off by pressing and quickly releasing buttons C and D respectively. 3 C D B About your Vehicle 173

Front “LIFT” system (optional) The specific warning lamp (see page 113) flashes continuously for the duration of the entire Front Lift system operating cycle, On request, the vehicle can be fitted with a front suspension while the vehicle symbol with an arrow pointing upwards and the “LIFT” system: this device acts on the front suspension and raises message “Front Lift moving” are shown on the left TFT display. the front of the car by approximately 40 mm (1.5 in.) to make When the system has been activated (front of the vehicle raised), an access to garages or steep ramps easier and avoid damaging the car. acoustic signal is emitted and the message “Front Lift ON” appears The system can be activated when the engine is running at a for 5 seconds whereas the warning light on the panel stays on in speed of below 40 km/h (25 mph) by pressing button A on the fixed mode until the system is deactivated. centre console. At speeds of over 40 km/h (25 mph), the system To deactivate the system, press button A again: at the start of is deactivated whereas if it is already activated, it is automatically the deactivation cycle, the warning light on the panel starts to deactivated when exceeding 40 km/h. flash again whereas the vehicle symbol with an arrow pointing downwards and the message “Front Lift moving” appears on the left TFT display. The message remains until the system has been completely deactivated. A LIFT moving 174 About your Vehicle

If the engine is turned off with the front suspension lift activated, In the event of engine failure, the “LIFT” system can however be the following message appears on the left TFT display at key-off: activated by pressing button A for 10 seconds. In this way, the “LIFT ON. Set LIFT to OFF”. Turn the key back to position II (key- vehicle front can be lifted even in emergencies when the engine is on) and press button A to lower the vehicle. If it is not manually turned off (for example, to load it onto the ramp of a breakdown deactivated by pressing the button, within 15 seconds of turning off vehicle). the engine, the system is automatically deactivated. Important note Warning The front suspension lift should only be used for the purposes The system has not been designed to remain activated when described above and not to drive over speed control systems the engine is turned off and the vehicle is stationary. If the (e.g. traffic calmers) more quickly. engine is turned off with the front lift activated, the vehicle is automatically lowered after 15 seconds. 3 Do not use the front suspension lift to park the vehicle on obstacles (e.g. pavements); these obstacles may come into contact with the front of the vehicle and damage it once the system has been deactivated. LIFT ON About your Vehicle 175

CCM active brake cooling system When the system is enabled, i.e. when the two front air inlets are open, the message “CCM disc brakes cooling ON” and the specific The vehicle has an “Active Brake Cooling” system, which opens the symbol will be displayed for 5 seconds on the left hand TFT two front CCM B brake air inlets in certain conditions. display (see page 112). This enables a bumper design with clean lines, and improved side After 5 seconds, the symbol will remain in the top display for the flows and greater aerodynamic resistance. entire time the system is active. CCM disc B B brakes cooling ON 176 About your Vehicle

System failure In the event of a system failure, the specific symbol and the message “CCM disc brakes cooling system failure” are shown on the left hand TFT display. Warning In the event of a CCM brake cooling system failure, avoid particularly strenuous use of the brakes (e.g. track use). Contact the Ferrari Service Network as soon as possible. 3 CCM disc brakes cooling system failure About your Vehicle 177

Seat adjustment Basic seat The seat position can be electrically adjusted using the special Warning controls. Three adjustments are possible using control D: As with all adjustment, seat adjustment must be performed when the vehicle is stationary. - backward/forward adjustment: push the control forwards or backwards - height adjustment: push the control up or down Warning - seat inclination (tilting): push the front or rear end of the control Never place your hands under the seat or near its moving parts up or down to adjust seat inclination. when adjusting. If you do so, movement of the seat may cause injury to hands or fingers. Warning Forward/backward adjustment must take into account the fact Correct adjustment is very important for enhanced driving comfort that airbag devices are placed in front of the driver and the and maximum efficiency of the passive safety systems. passenger. Correct adjustment ensures there is adequate space between the airbag and the driver/passenger (see page 49). D 178 About your Vehicle

Seat back rake adjustment Lumbar support adjustment (Full Electric option) Use control E to adjust the seat back rake. Push the control forward Use control F to adjust the seat backrest lumbar support. Push the or backward to adjust the seat back rake. horizontal arrows on the control left or right to increase or decrease lower lumbar support. Push the vertical arrows on the control up or down to increase or decrease upper lumbar support. Backrest and cushion side width adjustment (Full Electric option) Use control G to pneumatically adjust the width of the backrest and seat cushion sides. Push the horizontal arrows on the control left or right to increase or decrease the width of the seat cushion sides. Push the vertical arrows on the control up or down to increase or decrease the width of the backrest sides. 3 G F E About your Vehicle 179

Driver’s seat position memory (Full Electric option) With reverse gear engaged, the position of the passenger external When a door is open and the key is in position 0, the seat can be rear-view mirror can be adjusted to a position other than the moved for a limited period (approx. 15 sec.). Each time a door is driving position, to help parking manoeuvres. This position can be opened or both doors are closed and the key is set to OFF, the seat memorised along with all the other memorisable positions. can be moved again for a limited period. If the personalised reverse gear position is never set, when the The seat position can only be memorised when the key is in reverse gear is engaged, the passenger external rear-view mirror position II, by pressing one of the three buttons 1, 2 or 3 (H) each will in any case move slightly downwards and inwards (compared one corresponding to a memorisable position. Pressing one of these with the driving position). buttons for longer than 3 seconds memorises the position of the driver seat, rear-view mirrors and steering wheel (confirmed by Seat heating system (Full Electric option) emission of a double tone). Turn control N to activate the seat heating function. To recall the memorised position, press one of the buttons H and When this function is activated on one or both seats, the symbol release it within 3 seconds. Operation begins as soon as the button appears on the left TFT display for 5 seconds. Using control N, the is released. driver can adjust the heating, choosing from 3 levels identified on Recalling the memorised position is not allowed when the vehicle the control with the numbers 1, 2 and 3. In position 0, seat heating is in motion. If the vehicle starts to move while the memory recall is is not activated. being operated, the seat and column do not stop moving and reach the memorised position. H N 180 About your Vehicle

Tilting the backrest Racing seat (optional) To tilt the seat, pull lever L up and push the backrest towards the The seat position can be adjusted using the special controls. front of the vehicle. When the backrest goes back into position, it will automatically Backward/forward adjustment block once it has reached the correct position. Pull lever P up and slide the seat forward or backward to the desired position. Warning Release the lever and “wiggle” in the seat to check that it is locked Do not use the electric seat adjustment controls when the in place. backrest is tilted. Warning Forward/backward adjustment must take into account the fact 3 that airbag devices are placed in front of the driver and the passenger. Correct adjustment ensures there is adequate space between the airbag and the driver/passenger (see page 51). L P About your Vehicle 181

Seat back rake adjustment Tilting the backrest Use control Q to adjust the seat back rake. To adjust the rake, press Pull lever R to tilt the backrest forward. the front or back of the control. R Q 182 About your Vehicle

Adjusting the steering wheel Electric adjustment (optional) It can only be adjusted if the ignition key is in position II. Move The steering wheel can be adjusted for rake and reach. control B, to the left of the steering column. On versions with a driver's seat with memory, the position of the steering wheel is Warning memorised together with the position of the external rear-view mirrors when the seat position is memorised. Do not adjust the steering wheel when the vehicle is moving. Mechanical adjustment 1) Unlock lever A by pushing it forward. 2) Adjust the position of the steering wheel. 3) Lock the steering wheel by pulling lever A until it locks into 3 place. A B About your Vehicle 183

Rear-view mirrors External rear-view mirrors These mirrors can be electrically adjusted using control C (with the ignition key in position II) and are equipped with defogging Internal rear-view mirror elements. Hold the internal rear-view mirror and move it to the required 1) Mirror selection: turn control C to the left or right lock position position. to select the mirror that requires adjusting. The internal rear-view mirror is fitted with an electrochromic 2) Mirror positioning: move control C in the four directions (up – mirror that automatically darkens to reduce the dazzling effect of down – right – left) to adjust the selected mirror. the reflected light on the driver. The speed with which the mirror darkens depends on the intensity of the light. 3) Mirror closure (optional): turn control C to the lower central lock position to close the rear-view mirrors. By pressing button B you can activate/deactivate the electrochromic mode. When the electrochromic mode is activated, the green Once adjusted, move the control C into the upper central position LED D comes on. where it will be locked in order to avoid changing the external mirror setting inadvertently. The mirrors will yield in both directions in the event of a collision: if necessary, the mirrors can be pushed both backwards and forwards. D C C B 184 About your Vehicle

On versions equipped with a driver's seat with memory, every time the seat position is memorised, the external rear-view mirror Warning position is also stored automatically, both for the normal travelling Do not adjust the steering wheel when the vehicle is moving. direction and reverse manoeuvring. To memorise a new position of the external rear-view mirrors, turn the ignition key to position II and adjust the position of the The external rear-view mirrors are fitted with an electrochromic mirrors; then engage reverse and reposition the external mirrors to mirror. ensure the best possible visibility to perform the manoeuvre, then disengage reverse gear. Finally, press one of the buttons 1, 2 or 3 on the seat (see page 180), each one corresponding to a memorisable position, until a double tone confirms that the procedure is complete. The new position of the external rear-view mirrors will be 3 automatically memorised together with the seat position. In addition, the mirror positions can be adjusted for both the normal travelling direction and for reverse manoeuvring. About your Vehicle 185

Air conditioning and heating system Controls 1 Left-hand temperature setting and AUTO button Operating modes 2 A.C. compressor activation/deactivation 3 Single-zone mode activation/deactivation Automatic 4 Air distribution fan speed This mode automatically adjusts the air distribution, temperature 5 Rear window demist activation/deactivation and ventilation levels according to the temperature set by the user. 6 Windscreen demist activation/deactivation 7 Right-hand temperature setting and AUTO button Partially Automatic 8 Right-hand air distribution mode setting This mode allows the user to adjust certain parameters manually, 9 Air recirculation while others remain automatic. 10 Left-hand air distribution mode setting. Manual This mode allows the user to set the values to suit the passengers’ needs. 1 2 3 4 5 6 7 10 9 8 186 About your Vehicle

Left-hand temperature setting and AUTO button (1) Air distribution fan speed (4) This is used to select the required air temperature in the left-hand The four setting positions allow the occupants to select the air flow side of the passenger compartment; the AUTO button is used to rate. activate automatic operation (LED on). Rear window demist activation/deactivation (5) A.C. compressor activation/deactivation (2) Press this button (LED on) to activate rear window defogging/ This is used to activate (LED on) or deactivate (LED off) the A.C. demisting. compressor. Windscreen demist activation/deactivation (6) Single-zone mode activation/deactivation (3) Press this button (LED on) to activate windscreen defogging/ This is used to activate (LED on) or deactivate (LED off) the single-zone operating mode. demisting. 3 1 2 3 4 5 6 About your Vehicle 187

Right-hand temperature setting and AUTO button (7) Air recirculation (9) This is used to select the required air temperature in the right-hand If released (LED off), the air flow comes from outside the side of the passenger compartment; the AUTO button is used to passenger compartment. activate automatic operation (LED on). When outside temperatures exceed 32 °C (90 °F), the air recirculation feature remains on with a 60-second pause every Right-hand air distribution mode setting (8) twenty minutes to refresh the air. This is used to select one of the six air flow distribution modes in If you activate the windscreen washer function, the air recirculation the right-hand side of the passenger compartment. feature activates for 20 seconds, to prevent any smell of detergent products from entering the passenger compartment. If pressed (LED on), the air flow comes from inside the passenger compartment. The recirculation increases air heating or cooling. Left-hand air distribution mode setting (10) This is used to select one of the six air flow distribution modes in the left-hand side of the passenger compartment. Once the internal temperature has stabilised at the desired level, you are advised not to change the position of the temperature selection switch unless the external temperature changes drastically. 8 10 7 9 188 About your Vehicle

Maintenance The pollen filter must be replaced every year, as indicated in the Important note “Maintenance Schedule”. We recommend keeping the air flow set to open and directing the air flow to a neutral position. Important note The air coming out of the vents does not correspond to the Important note temperature requested by the user, but is the temperature required to maintain the desired temperature inside the Prolonged use of the air conditioning system with the side passenger compartment. windows open may cause condensation to form on the air vents. Adjusting the air vents 3 The adjustable air vents are positioned on the sides and in the central section of the dashboard. Use control A to adjust the air flow rate. Turned clockwise: open. Turned counterclockwise: closed. A About your Vehicle 189

Placing luggage in the luggage compartment Warning Warning Do not transport heavy items in the passenger oddment storage compartments. All luggage must be very carefully placed and secured in the luggage compartment. Luggage or heavy items that are not secured could be projected into the passenger compartment at Important note high speed in the event of a sudden change in direction, sharp Heavy loads affect vehicle handling: spread the weight evenly braking or an accident and increase the risk of serious injury. when placing luggage in the luggage compartment and try and place the heaviest items as low down and as far forward as Important note possible. To secure small, light loads in the luggage compartment, use, if possible, a rope or luggage net fastened to the special eyebolts shown in the figure. 190 About your Vehicle

Parcel shelf The rear panel D is fastened to the luggage compartment lid by The parcel shelf separates the luggage compartment from the two pins. To remove, release one of the two pins E by turning it passenger compartment and consists of two removable panels, C counterclockwise and removing it from its housing as shown in the and D. figure, while holding the panel with the other hand. The front panel C is held in position by a pin at each of the two ends. To increase vertical load space, the front panel C is removable: to remove the panel, open the hatch between the passenger and luggage compartments, incorporated in the front panel itself (see page 192), and pull the parcel shelf gently backwards to release the two lateral pins. 3 Warning Do not transport items on the parcel shelf: they could be projected into the passenger compartment at high speed in the event of a sudden change in direction, sharp braking or an accident and increase the risk of serious injury. D E C E About your Vehicle 191

Partition between passenger compartment and luggage compartment For carrying particularly bulky objects, the panel separating the rear shelf from the luggage compartment may be folded down to allow access between the luggage and passenger compartments. To lower the hatch, pull the tabs A and fold the hatch against the front panel of the parcel shelf. The hatch is held in place by two magnets at the ends of the parcel shelf. To close the flap, put it back into its original position and press until it clicks into place. Warning After closing the panel, always make sure it has clicked back into place properly to prevent it accidentally opening while driving. A A 192 About your Vehicle

Passenger compartment accessories Opening of the glove compartment can be deactivated by pressing button C. Recall the MENU screen page on the left hand TFT display (see page 90), select the options “Car setup” and “Glove Glove compartment box”, then select OFF. To reactivate opening using the button, This is located on the passenger side of the dashboard. To open it select ON. press the OPEN C button: the glove compartment will move down slowly by way of a damped opening mechanism. Sun visors The glove compartment is illuminated by an internal light that The sun visors can be moved by pulling them down towards the comes on automatically when it is opened. windscreen and sideways by unhooking them from the fastener and turning them towards the door glass. 3 Warning There is an illuminated mirror on the back of the passenger sun visor. Keep the glove compartment closed while driving. To close the glove compartment, push the top part until you hear the click of the lock. C About your Vehicle 193

Oddment storage compartments There are several oddment storage compartments in the passenger compartment located on the lower part of the doors and on the centre console. The armrest on the centre console can be moved forwards. The centre console has a cup holder. 194 About your Vehicle

12V power socket The vehicle has a power socket D, positioned in the glove compartment under the armrest. The socket can be used to power small electrical appliances including: mobile phones, lights, vacuum cleaner and any other accessory with absorption not exceeding 140 Watts and a voltage of no more than 12 Volts. Warning Prolonged use of this device may discharge the battery. Do not try to insert plugs into the power socket that are not the right size and shape. 3 Warning Use the power socket to connect the tyre repair and inflation kit in an emergency ONLY for the amount of time strictly necessary. D About your Vehicle 195

Toolkit................................................................. 198 Replacing light bulbs............................................ 203 Replacing a fuse................................................... 206 Replacing a wheel................................................. 215 Towing................................................................. 218 Battery................................................................. 220 Battery conditioner............................................... 224 EPB emergency release.......................................... 228 Park Lock emergency release................................. 230

4 ADVICE FOR EMERGENCY SITUATIONS

Toolkit Warning Repair work using the toolkit requires: Tool kit - suitable protective equipment (e.g. gloves) Stored in the luggage compartment, it contains the necessary tools - adequate precautions to be taken (e.g. during tyre replacement for emergency repair jobs: never lie under a vehicle raised by a jack) • pair of cotton gloves; - minimum specific expertise when working in contact with • set of fuses; electrical parts/components (e.g. battery). • pliers for removing fuses; • tow hook; • insulated cutting pliers; • funnel for emergency fuelling; • screwdriver for slotted and crosshead screws; • EPB emergency release tool; • Park Lock emergency release tool; • emergency tyre repair and inflation kit. 198 Advice for Emergency Situations

Warning The Electric Parking Brake (EPB) emergency release tool and the Park Lock emergency release tool may only be used by specialised workshop technicians, as indicated on the label on the tool kit. 4 Advice for Emergency Situations 199

Emergency tyre repair and inflation kit Stored in the luggage compartment, it can be used in the event of a Warning puncture or low tyre pressure to repair and/or inflate a tyre enough Damage to the wheel rim that causes air leaks cannot be to continue the journey safely. repaired. Do not remove foreign objects (screws or nails) that have penetrated the tyre. Important note To use the tyre repair and inflation kit correctly, refer to the Warning instruction booklet provided with the kit. After using the repair kit, the vehicle must be considered in an emergency situation: drive with the greatest care (maximum Warning permissible speed 80 km/h - 50 mph). Give the instruction manual supplied with the kit to the personnel that will handle the tyre repaired with the tyre repair Warning kit. Apply the sticker supplied with the kit where it can easily be seen by the driver to indicate that the tyre has been treated with Warning the tyre repair kit. In the event of damage caused by foreign objects, the kit can be Drive carefully especially on bends. used to repair tyres with cuts of up to 4 mm in diameter on the Avoid sudden accelerations or braking. tyre tread and shoulder. Warning Warning The kit is to be used to temporarily repair only one tyre Punctures cannot be repaired on the sides of the tyre. Do not punctured by small objects: the kit may not be useful in the case use the tyre repair kit if the tyre has been damaged after driving of large punctures or tearing. with a flat tyre. 200 Advice for Emergency Situations

Important note Warning After driving for approximately 10 minutes, stop and recheck Keep the kit in its box and out of children’s reach. the tyre pressure. Do not inhale or swallow the fluid contained in the spray can Remember to apply the parking brake. and avoid contact with the skin and eyes. Warning Warning If the pressure has decreased below 1.8 bar (26.11 psi), do The spray contains ethylene glycol and latex. not continue driving: the kit cannot guarantee the correct hold The latex may cause an allergic reaction, is harmful if swallowed because the tyre is too damaged. Contact the Ferrari Service and is irritating to eyes. May cause sensitisation by inhalation Network. and skin contact. Avoid contact with eyes, skin and clothing. If the tyre pressure is at least 1.8 bar (26.11 psi), restore the In case of contact, rinse immediately with plenty of water. If correct pressure and continue driving. swallowed, do not induce vomiting, rinse mouth, drink plenty of Drive very carefully to the nearest Ferrari Service Network. water and seek immediate medical advice. Keep out of reach of children. The product should not be used by asthma sufferers. Do not inhale vapours during use. In the event of an allergic 4 Warning reaction, seek immediate medical advice. Store the spray can in its special case away from sources of heat. The repaired tyre must be replaced as soon as possible and the The liquid sealant has an expiry date: the expiry date is workshop personnel must be informed that the tyre was treated indicated on the kit. with tyre repair fluid. Advice for Emergency Situations 201

Useful accessories Environment In addition to the tools supplied with the vehicle, the hazard warning triangle and fluorescent safety jacket should always be Replace the spray can containing the expired liquid sealant. Do kept on board in order to signal hazardous situations in compliance not dispose of the spray can and sealant in normal domestic with regulations. waste. Dispose of in accordance with national and local regulations or ask the Ferrari Service Network to take care of disposal. Warning The sealant in the kit cartridge can damage the sensor inside the wheel rim on vehicles fitted with a tyre temperature and pressure monitoring system (TPMS). If this occurs, the sensor must be replaced. Contact the Ferrari Service Network. Warning Wear the protective gloves supplied with the tyre inflation and repair kit. 202 Advice for Emergency Situations

Replacing the front and rear light bulbs Replacing number plate light bulbs To replace a number plate light bulb, proceed as follows: Important note • remove the light from the right side where there is a spring clip; To replace the front and rear light bulbs, contact the Ferrari • remove the transparent cover A from its housing; Service Network. • replace the bulb by removing connector B from its housing; To adjust the headlight beam, please contact the Ferrari • refit the connector and transparent cover by inserting it first from Service Network. the left side and then pressing on the other side. 4 B A Advice for Emergency Situations 203

Replacing other light bulbs Glove compartment, underdoor and luggage compartment bulbs • Use a screwdriver to gently prise under the edge of the Roof dome light transparent cover G and lift it. • Use a screwdriver to gently prise under the edge of the • Completely remove the transparent cover from its housing. transparent cover C of the dome light and remove it from the roof • Take the bulb out of its clips. panel. • Replace the bulb. • Replace the bulb D or E or F. • Refit the transparent cover and make sure that the wires are not • Refit the dome light and make sure that the wires are not trapped trapped by inserting it first from the connector side and then by inserting it first from the connector side and then pressing on pressing on the opposite side. the opposite side. Follow the same procedure for replacing the underdoor light bulbs and the luggage compartment dome light bulbs. D E F G C 204 Advice for Emergency Situations

Light bulbs (12V except for high beam and low beam) Type Power Low beams and high beams gas-discharge (XENON) Das Front running lights LED Front turn indicator lights LED Side turn indicator lights incandescent T4W Running and stop lights LED Reverse lights LED Additional stop light LED Rear turn indicator lights LED Rear fog light Number plate lights incandescent incandescent H21W 5W 4 Passenger compartment dome light incandescent 8W Spotlights incandescent 5W Glove compartment light incandescent 5W Underdoor courtesy lights incandescent 5W Luggage compartment lights incandescent 5W Advice for Emergency Situations 205

Replacing a fuse Fuse colours When an electrical device is not working, check that the Ampere corresponding fuse is not blown. yellow ochre 5 A - Unblown fuse brown 7.5 B - Blown fuse red 10 Important note light blue 15 If the problem persists, contact the Ferrari Service Network. yellow 20 white 25 green 30 Important note When replacing a fuse, always use fuses of the same amperage Maxi fuse colours (same colour). Ampere The tool bag in the tool kit contains spare fuses. To remove the yellow 20 fuses, use the pliers C in the tool bag. green 30 orange 46 red 50 A blue 60 C B 206 Advice for Emergency Situations

Location of the fuse and relay boxes A - Fuses and relays in battery compartment (right-hand side of engine compartment) B - Body Computer fuses and relays (dashboard to left of steering wheel) C - Fuses and relays in passenger compartment on passenger side (under passenger side footrest) A D - Fuses and relays on centre console (under the glove compartment) E - Fuses and relays in luggage compartment (behind right-hand luggage compartment shield) B 4 C D E Advice for Emergency Situations 207

Fuses and relays in battery compartment F-71 40 Front lift pump To access these fuses: F-72 40 Parking brake power • open the engine compartment lid and remove the cosmetic shield F-73 70 Dashboard ECU power on the right-hand side of the engine compartment by unscrewing the screws shown in the figure; Body Computer fuses and relays • remove the cover of box A located above the positive terminal. To access these fuses, remove the dashboard panel 1 to the left of the steering wheel. Important note Only open the boxes containing the fuses that need to be Important note checked to avoid damaging other components. Only open the boxes containing the fuses that need to be checked to avoid damaging other components. Box A contains these fuses: Ref. Amp. Use CAL5 CAL5 Power supply (starter motor and alternator) Engine relay and fuse ECU power supply F-70 150 (SCM) A 208 Advice for Emergency Situations

Box B contains these fuses and relays: Dashboard ECU devices F-39 15 Ref. Amp. Use (NBC interconnection) F-40 30 Heated rear window F-12 15 Right high beam F-41 15 Heated nozzle power supply F-13 15 Left high beam F-42 7.5 Alternator INT/A for dashboard ECU, Body Computer F-31 7.5 Node and air conditioning and heating relay F-43 30 Windscreen washer/wiper relay power supply coils F-44 20 Passenger seat heating, cigarette lighter Dome lights, foot well and step lights, Side F-47 30 Driver-side door, driver-side power window F-32 10 Marker relay coil and glove compartment button Passenger-side door, passenger-side power Electronically controlled Gearbox Node F-48 30 F-33 30 window control unit Rain and twilight sensor, parking sensors, Stop light control, clutch control, air parking brake control, column adjustment F-35 7.5 conditioning node F-36 10 Parking sensors, fuel filler flap relay coil F-49 7.5 control, hazard warning lights, Steering Wheel Node, Differential Control Node, radio, CAN box interface 4 F-37 10 Instrument Panel Node F-50 7.5 Airbag Node, weight sensor F-38 15 Luggage compartment lock actuator 1 F-72 F-73 F71 F-71 F-72 F-73 F-70 F-70 CAL2 CAL5 Advice for Emergency Situations 209

F-51 7.5 Electronically controlled Gearbox Node, Fuses and relays in passenger compartment on passenger side ignition button To access these fuses, remove the passenger side footrest 2 by F-52 15 Power socket, driver seat heating unscrewing the screws as shown in the figure. T01 20 Low beam relay Box C contains these fuses and relays: T11 30 Heated rear window relay Ref. Amp. Use T12 30 Service relay 1 (dependent on INT/A ignition F-01 40 +30 Radiator fan relay 2 switch) F-02 40 Bus-Bar power supply for F-102, F-105 T13 50 Jumper (service power supply 2) F-03 70 Bus bar power supply for F-107, F-108, F-91, F-92, F-109, F-104, F-103 F-04 50 +30 ABS (pump) F-05 40 +30 Air conditioning Node F-06 40 +30 Radiator fan relay 1 F-07 20 +30 Horn relay F-08 7.5 Air conditioning and heating system compressor F-09 7.5 +30 Alternator sensing 2 210 Advice for Emergency Situations

F-10 30 +30 Bus bar for F-94, F-95, F-106 F-89 10 +15 Right cylinder bank injection system F-11 25 Left bank oxygen sensor F-91 15 +30 Tyre pressure node, LH headlight LED F-14 15 +30 High beam relay module relay F-15 30 +30 Ignition switch F-92 7.5 +30 Right headlight LED module relay F-16 25 +30 Right bank engine control power supply F-94 15 +30 Radio/CAN box/ICP/clock spring/Japan navigation system stabiliser F-17 25 +30 Left bank engine control power supply F-95 10 +30 Current stabiliser F-19 20 +30 Active aerodynamic relay F-102 10 +30 ABS (electronic) F-20 30 +30 Right cylinder bank injection system main relay F-105 30 +30 ABS (valves) F-21 10 +30 Active aerodynamic control and front lift F-106 7.5 +30 Passenger compartment control lighting power supply F-107 10 +30 Right cylinder bank injection system F-22 15 Left bank (ignition coil) power supply F-24 F-30 15 30 Right bank (ignition coil) +30 Starting relay F-108 F-109 10 7.5 +30 Left cylinder bank injection power supply +30 Supplementary stop light relay 4 F-81 40 +30 Fuel pump ESD ECU F-82 70 +30 Dashboard ECU and luggage compartment ECU power supply C F-83 50 +30 Air pump relay F-84 30 +30 Suspension Control Node F-85 25 Headlight washer F-87 25 Right bank oxygen sensors F-88 10 +15 Left cylinder bank injection system Advice for Emergency Situations 211

T02 30 High beam relay T28 30 Active aerodynamic release relay T03 30 Passenger compartment control lighting relay T29 30 Active aerodynamic locking relay T05 30 Supplementary stop light relay T30 50 Air pump relay T07 50 Horn relay T31 30 Headlight washer pump relay T08 30 Air conditioning and heating system T38 30 Left headlight LED module power supply compressor relay relay T09 30 Left cylinder bank injection system main relay T39 30 Right headlight LED module power supply T10 30 Right cylinder bank injection system main relay relay T14 30 Windscreen washer pump relay T17 10/20 INT/A relay (devices excluded at ignition) T19 30 EPB-activated stop light control relay T20 30 Starting relay T26 30 Windscreen wiper first speed relay T27 30 Windscreen wiper second speed relay 212 Advice for Emergency Situations

Fuses and relays on centre console F-67 7.5 Side Markers 2 (RH front and LH rear) To access these fuses, remove the rear part 3 of the glove F-80 30 +30 Bus bar power supply for F-97, F-98, F-99 compartment on the centre console. T21 50 Side Marker relay Box D contains these fuses and relays: T22 30 Reverse light relay Ref. Amp. Use T23 30 Fuel filler flap relay F-54 30 +30 HiFi amplifier T25 30 Electronically controlled gearbox main relay F-56 30 +30 Driving Position Node F-57 7.5 Side Markers 1 (LH front and RH rear) F-59 7.5 Reverse light power supply F-60 30 +30 Passenger Position Node F-63 20 +30 Electronically controlled gearbox main relay F-64 F-65 7.5 20 Fuel filler flap actuator power supply +30 Door lock actuator 4 F-66 30 +30 Bus-Bar power supply for F-96, F-100, F-101 D 3 Advice for Emergency Situations 213

Fuses and relays in luggage compartment To access these fuses, remove the right hand luggage compartment panel. Box E contains these fuses and relays: Ref. Amp. Use F-96 10 +30 Luggage compartment lock relay +30 Electronic Passenger Position Node, F-97 10 luggage compartment striker plate F-98 15 +30 Battery conditioner socket F-99 7.5 +30 Semi-automatic Gearbox Node F-100 7.5 +30 Driving Position Node, suspension lift ECU T40 30 Glove compartment lock relay T41 30 Luggage compartment lid lock relay E 214 Advice for Emergency Situations

Replacing a wheel • additional tool bag C containing the jack for raising the vehicle and the socket wrenches for operating the jack and tightening the wheel stud bolts. Important note If one or more wheels need to be replaced, proceed as follows: Warning • replace the wheel stud bolts with damaged threads or tapers The space saver spare wheel must only be used for short trips in • carefully clean the wheel stud bolts before fitting the event of an emergency. • do not lubricate the contact surfaces between the stud bolt When the spare wheel is fitted, never exceed the maximum and the wheel rim and between the wheel rim and the brake speed of 80 km/h (50 mph) and drive carefully, especially disk. around bends and when overtaking, avoiding sudden In order not to remove the antilock coating, do not clean the acceleration or braking. wheel rim cones with solvents or aggressive products. Do not exceed the approved weight limits. Do not fit snow chains on the spare wheel. Never fit more than one spare wheel at a time. 4 Collapsible space saver spare wheel (optional) On request, the vehicle comes with a kit containing: • collapsible spare wheel A with space-saving tyre; label B indicates Important note the maximum speed allowed of 80 km/h (50 mph); Failure to comply with these instructions could lead to loss of control of the vehicle and consequently damage to the vehicle and injuries to its occupants. A B C Advice for Emergency Situations 215

Replacing a wheel • Raise the vehicle carefully using jack E until the wheel is off the • Position the vehicle on an even surface, then block the rear wheels ground. by applying the parking brake. Warning Warning If the jack is not positioned correctly, the vehicle could slip off. Make sure that the vehicle is in a safe position by applying the Make sure that no part of the body is underneath the vehicle parking brake. while changing the wheel. The supplied jack must only be used for changing wheels. • If necessary, switch on the hazard warning lights and place the hazard triangle at the required distance from the vehicle. • Unscrew the five stud bolts and remove the wheel. • Take the space saver spare wheel and tools out of the luggage • Fit the uninflated collapsible spare wheel. compartment. • Screw the stud bolts into place but do not tighten them. • Loosen the five wheel stud bolts approximately one turn each using wrench D supplied. Warning • Place the base of the jack E on flat firm ground under one of the jacking points F on the underfloor as shown in the figure. Inflate the collapsible spare wheel before lowering the vehicle to avoid damaging the rims. • Inflate the collapsible spare wheel using the inflation kit. F E D 216 Advice for Emergency Situations

Warning The kit must be used in “tyre inflation” mode. Refer to the instruction manual supplied with the kit. • Inflate the spare wheel to the indicated pressure (see page 30). • Lower the vehicle and remove the jack. • Tightly fasten the stud bolts, alternately going from one stud bolt to one that is diametrically opposite. As soon as possible, tighten the stud bolts with the torque wrench to a torque of 100 Nm. Warning The space saver spare wheel does not have a tyre pressure monitoring sensor (see label on spare wheel tool bag). After fitting, it is not checked by the system but complies with 4 international regulations ECE R64/01. After fitting, we recommend that you go to the nearest Ferrari Service Network. Advice for Emergency Situations 217

Towing Warning When towing the vehicle, avoid using anchor points that are not designed for the tow hook inserted in housing C. While towing the vehicle, you must comply with Road Regulations. Proceed as follows: • Take the tow hook out of the tool bag. • Using a screwdriver, prise open the circular cap B on the left hand Warning side of the front bumper. Do not tow the vehicle by attaching to levers, suspension and • Tightly screw the tow hook into housing C. wheel rims but only to the tow hook properly fitted in place. • Release the EPB. Keep the key in position II to enable the lights to work and • Release the Park Lock. prevent the steering wheel from locking if it is turned; when towing the vehicle, do not start the engine. Warning In the event of an electrical system failure, release the EPB and Important note Park Lock manually (see pages 226-228). Remember that when the engine is switched off, the power steering and brake servo functions do not work. B C 218 Advice for Emergency Situations

Fuel inertia switch The fuel inertia switch is a safety device which deactivates the fuel pump relays if a collision occurs. A specific symbol appears on the left TFT display (see page 109) and the hazard warning lights activate to indicate that this switch has been triggered. When the fuel inertia switch is activated, the doors are also unlocked (if locked) and the central dome light comes on. Warning The fuel pump relays can be reactivated by pressing button A on the floor in front of the driver's seat. 4 A Advice for Emergency Situations 219

Battery Warning The battery is located on the right-hand side of the engine compartment: to access it, remove the cosmetic shield by The battery must only be removed from the vehicle by the unscrewing the three screws shown in the figure. Ferrari Service Network. Removal of or damage to the battery affect the vehicle software ECUs and may result in error codes, data loss or inaccurate data. Checking the battery The vehicle is equipped with a sealed lead acid battery that does not require maintenance. Warning Do not place the battery near sources of heat, sparks or naked Warning flames. The battery does not need topping up with distilled water or sulphuric acid. • Periodically check that the terminals and pins are clean and firmly secured. • Visually inspect the outer casing for any cracks. • If the battery overcharges, it will wear out quickly. Have the vehicle electrical system checked if the battery tends to discharge easily. Disconnecting the battery Before disconnecting the battery, deactivate the electronic alarm using the remote control. Warning Never disconnect the battery from the electrical system when the engine is running. Before disconnecting the battery, lower the side windows by at least 2-3 centimetres (0.8-1.2. in.) to avoid damaging the strips when opening and closing the doors. 220 Advice for Emergency Situations

Detach the terminal from the battery: the power supply from the Warning battery to the electrical system is cut off. When the battery is connected and charged, this operation is automatically performed when the doors are opened and closed. Warning The windows must remain lowered until the charged battery is The battery quick release must only be used if the battery reconnected. If the battery is discharged and the windows are conditioner cannot be connected. fully up, only open the doors when strictly necessary and take great care; do not close them again until the windows can be lowered. Warning Place the clamp so that it does not come into contact with the Important note battery terminal or other metal parts of the vehicle. We recommend using the battery conditioner if the vehicle is going to left unused for a long period. Reconnecting the battery To cut off the power supply from the battery to the electrical system, use the quick release C on the left side of the battery. Use Place the clamp on the battery and fasten it by closing the locking lever. 4 the locking lever to loosen the terminal. Each time the battery is reconnected, do the following before starting the engine: - close both doors and close the luggage compartment lid; unlock and lock the doors using the remote control; open the luggage compartment lid using the remote control; - adjust the clock (date and time on instrument panel); - close both doors and fully raise the driver side and passenger side windows to their upper limit; check that the windows move down to the “target position” when the doors are opened. C Advice for Emergency Situations 221

Emergency starting Warning If the battery is flat, you can perform an emergency start by Before starting the engine, wait at least 60 second with the connecting the special jump leads to the battery of another vehicle, ignition key in position II to allow the electronic system that a portable jump starter or an external battery. controls the motor-driven valves and the AC ECU to run a self- acquisition process. Important note During this period, no devices must be activated. Emergency starting can only be performed with batteries with a nominal voltage of 12V. The Motronic ECU self-acquisition cycle will only function correctly when the intake air temperature is above 5 °C (41 °F). After removing the battery from the vehicle or disconnecting it Important note from the electrical system using the battery master switch, it is For emergency starting, only use leads that do not allow reverse important to check that the external temperature is within the polarity, with sufficient cross-section and insulated clamps. indicated values when reconnecting before performing the self- acquisition cycle. 222 Advice for Emergency Situations

To perform an emergency start, do the following: • Start the engine. • Apply the parking brake. • Disconnect the jump lead from the earthing point and then from • Deactivate all the electrical devices. the positive terminal of the battery on your vehicle. • Remove the cosmetic shield on the right hand side of the engine compartment by unscrewing the three screws shown in the figure. Warning • Remove the cover A of the fuse box located above the positive After emergency starting, go to the nearest Ferrari Service terminal. Network immediately to get the battery checked. • If emergency starting is performed using the battery of another vehicle, leave the engine on the other vehicle to idle. • Using the jump leads, connect the positive terminal of the battery to the positive terminal of the portable jump starter or external battery going from the battery on your own vehicle. • Connect the negative terminal of the portable jump starter or external battery to an earthing point on your vehicle using the jump lead going from the external battery. 4 A Advice for Emergency Situations 223

Battery conditioner Warning The vehicle is equipped with a battery conditioner to maintain and recharge the battery. Place the battery conditioner where it can be easily seen away from heat sources and out of children's reach. Important note After connecting the battery conditioner to the socket in the Using the battery conditioner will extend the life of the battery. vehicle, run the connection cable underneath the luggage compartment lid near the bottom corner. The device is kept in a pocket inside the car cover bag supplied with the vehicle. Important note The battery conditioner connection socket is located on the left Do not run the connection cable out of the vehicle in positions hand side of the luggage compartment behind plug B. other than those indicated to prevent damaging the seals and/ To access the socket, remove the plug B indicated in the figure. or the cable. If you do not plan to use the vehicle for over a week, we recommend you connect the battery conditioner to keep the battery in perfect working order. B 224 Advice for Emergency Situations

Exhaust system overheating alarm devices Warning (“Slow Down” function) The engine cannot be started as long as the battery conditioner If the engine is running unevenly resulting in exhaust system is connected to the vehicle socket. overheating, the “Slow Down” function is activated: a special symbol (see page 111) appears on the left TFT display accompanied by a message. Important note The message varies according to three alarm levels: Additional technical information on the use of the device can be • Temperature high: “Catalysts temp. high. Slow down”. found in the manual provided inside the pocket of the car cover • Temperature too high: “Catalysts temp. too high. Engine bag. performance limited”. • Catalytic converter temperature system failure: “Catalysts temp. not plausible. Go to dealer slowly”. Displaying of the message is controlled by the thermistor via the engine control ECU. Warning 4 Incorrect use of the vehicle may cause the “Slow Down” function to be activated. Warning If the temperature is high: slow down immediately so that the exhaust system temperature decreases. Advice for Emergency Situations 225

Clutch overheat alarm devices Warning Extremely high performance use of the vehicle at high engine If the temperature is too high: speeds for prolonged periods and at high ambient temperatures the temperature in the catalytic converters has reached a may cause the DCT gearbox clutches to overheat. In this case, the dangerous level and could damage them; if you continue to following safety warnings will be displayed on the left TFT display, drive, the engine control ECU intervenes and reduces the corresponding to two different alarm levels: torque produced by the engine. • The message “Clutch overheated” The torque limit remains active until the catalytic converter • The message “Clutch overheated” accompanied by an acoustic temperature goes down to normal operating values. signal. When the message “Clutch overheated” is displayed, the driver may notice a difference in the behaviour of the system during gearshifts Warning and/or during standing starts. If catalytic converter temperature system failure information is displayed: - the engine control ECU intervenes and reduces the torque produced by the engine - the driver must slow down and slowly drive to the nearest Ferrari Service Network to have the engine parameters checked. Warning If the EOBD warning light (see page 110) comes on at the same time as the “Slow Down” message, go to the Ferrari Service Network to have the ECU error memory checked. Do not Clutch overheated proceed in any other way. 226 Advice for Emergency Situations

Engine malfunction alarm devices Important note If the “engine control system failure” (EOBD, see page 110) Certain high-performance actions (including but not limited to: warning light flashes or comes on permanently while the engine is “LAUNCH” control start, standing start with wheelspin with running, it indicates that the engine or the emission control system Manettino set to ESC OFF, etc.) may be inhibited to prevent may be malfunctioning. excessive overheating of the clutches: the system warns the The electronic system detects and isolates the error preventing driver that the action is not permitted by displaying the message damage to the engine or the production of harmful emissions. “Operation not admissible” on the left TFT display. Warning Warning When the “engine diagnostic system failure” warning light As soon as any of the warnings described above appear on the comes on, engine performance may be considerably reduced. left TFT display, the driver must slow down, continue driving Drive carefully, avoiding sudden acceleration and high speeds. at an engine speed between 2,000 and 3,000 rpm and minimise Contact the Ferrari Service Network immediately. gearshift frequency to allow the clutches to cool down as quickly as possible. These driving conditions must be maintained until the message “Clutch overheated” is no longer displayed. 4 Advice for Emergency Situations 227

Replacing brake pads Emergency release of the electric parking brake (EPB) Brake pads The front brake pads have a wear detector connected to the brake warning light; if this warning light comes on or braking is not Warning even, have the pad thickness and the state of the braking surfaces The release procedure must only be carried out by specialised checked. workshop technicians. The minimum brake pad thickness is 3 mm - 0.12 in. (thickness of If the system cannot be released, contact the nearest Ferrari the friction material only). Service Centre. Replacing brake pads When the brake failure warning light comes on, it means that Warning the front brake pads are excessively worn and must be replaced immediately. When the electric parking brake is deactivated manually, the vehicle may move. To keep the vehicle stationary, the Park Lock safety device must Warning be applied: make sure that the letter “P” appears on the gearbox To guarantee the quality of the components and proper display. installation, we recommend that you have the brake pads replaced at a Ferrari Service Centre. After replacement, avoid sudden braking until the new pads are seated properly (approximately 300 km - 186 mi). A Important note In the event of extreme usage (e.g. track use), the brake discs may generate noise and vibration. This phenomenon is normal and will cease after a short period of normal usage. 228 Advice for Emergency Situations

If the vehicle needs to be moved but the electric parking brake cannot be deactivated because the battery is flat or there is a failure Important note in the electrical system that controls it, the emergency release To release the brake completely, the wrench needs to be procedure described below must be performed. turned 50 times and it starts to be released after approximately • Take wrench A for EPB emergency release out of the tool bag. 20 turns. Warning Once the electric parking brake has been manually released, the Wrench A may only be used by specialised workshop EPB node records a failure at the next key-on and a special symbol technicians, as indicated on label C on the tool kit. and the following message are displayed on the left TFT display: “Parking Brake system revision. Go to dealer”. • Using the special rectangular slot B on the LH side of the tool kit (indicated by a label), place the wrench in the EPB release Warning housing (in the lower part of the slot, as shown in the figure) and The parking brake resumes normal operation, but it is important turn it clockwise: this loosens the parking brake cables. to go to the nearest workshop to have it calibrated and delete any errors in the error memory. Go to a Ferrari Service Centre. 4 Calibration is necessary for safety reasons. C B Advice for Emergency Situations 229

Park Lock emergency release Warning Warning When the Park Lock safety device is deactivated manually, the vehicle may move unexpectedly. The emergency release procedure must only be carried out by The vehicle is only kept stationary by the parking brake, if specialised workshop technicians. applied. If the system cannot be released, contact the nearest Ferrari Service Centre. The Park Lock manual release device is situated at the top right of the luggage compartment floor: to access the device, grip the panel at the points indicated by the arrows in the figure and tip the panel Warning backwards. This should be avoided unless absolutely necessary: To release the Park Lock, proceed as follows: - to tow the vehicle; • Take wrench D out of the tool kit. - if there is a Park Lock failure (displayed on the left TFT display with the message “Only manual unlock gearbox Warning allowed: See handbook”). Wrench D may only be used by specialised workshop technicians, as indicated on label C on the tool bag. C D 230 Advice for Emergency Situations

• Remove the rubber protection cap E. • Place wrench D in the manual release device housing F. • To perform the emergency release, turn wrench D counterclockwise for a quarter turn. If the electrical system allows it, check that the letter “N” appears on the gearbox display by turning the ignition key to position II. The following message will appear on the left TFT display: “Gearbox not in Parking position”. At the same time, an audible signal is repeated four times to indicate that it has been released. 4 E F Advice for Emergency Situations 231

Warranty Booklet................................................. 234 Maintenance........................................................ 234 Level checks.......................................................... 236 Wheels and tyres.................................................. 243 Maintenance of seat belts and pretensioners.......... 245 Cleaning the vehicle.............................................. 245 If the vehicle is stored for long periods................... 249

5 CARE OF THE VEHICLE

Warranty Booklet It is however advisable to report any small fault which occurs when using the vehicle (e.g. small leaks of essential fluids) to the Ferrari The vehicle comes with a “Warranty Booklet”. Service Network immediately and not wait until the next service is This contains the vehicle’s warranty validity conditions. due to correct the problem. Periodic maintenance services must be performed at least once a Warning year even if the specified mileage limit has not been reached (see “Annual Maintenance” in the “Warranty Booklet”). The warranty booklet also contains special blank spaces where the Ferrari Service Network can register the Displaying information on scheduled maintenance regular maintenance services performed, as indicated in the maintenance schedule. If the next scheduled maintenance deadline is approaching, at key- on, the message “Service Stop within:” is displayed for 5 seconds on the left TFT display followed by the number of kilometres Maintenance or days before vehicle servicing. The information is provided in It is essential to always keep the vehicle in proper working order kilometres or days according to the deadline that comes first. to ensure a long working life and to prevent any running defects, caused by negligence or lack of maintenance, and consequently to avoid hazardous situations. Important note All repair work on any safety system component must be performed by the Ferrari Service Network. Maintenance schedule At the intervals prescribed, the Ferrari Service Centres must Service stop within: perform all the fine-tuning and checking operations indicated in the “Warranty Booklet”. 100 km 234 Care of the vehicle

Information on scheduled maintenance can also be displayed on the left TFT display if requested by the driver irrespective of the scheduled deadlines. To do this, call up the MENU screen page (see page 90) and select “Service”. Chassis and bodywork maintenance The chassis has technological and manufacturing specifications that require that any operation be performed by staff specially trained to work with this innovative technology. It is of crucial importance to use equipment tested by Ferrari if the repair work is to be performed in accordance with rules of good workmanship. Proper execution of repair work ensures that the commercial value of the vehicle is preserved and the safety standards are complied with. Important note If the chassis is damaged in an accident, Ferrari advises customers to contact the Ferrari Service Network who will perform the necessary safety checks. The chassis, under standard conditions of use, requires no 5 maintenance; it is however advisable to contact the Ferrari Service Network at the intervals indicated in the “Warranty Booklet” in order to have it checked. Care of the vehicle 235

Level checks Ref. A B Engine oil tank cap A (page 238) Brake fluid tank cap B (page 241) D E C Windscreen and headlight washer fluid C reservoir cap (page 242) Coolant tank cap D (page 240) Power steering system fluid reservoir cap E (page 240) 236 Care of the vehicle

Important note The level checks must be performed at the intervals indicated in the “Warranty Booklet” or, in any case, before starting a long journey. Environment All the materials used for the following operations (e.g. cloths soaked with oil or grease, pans, etc.) must be disposed of in compliance with the environmental protection regulations. Important note Only use lubricants and/or fluids recommended by Ferrari (see the “Refilling” table on page 35). 5 Care of the vehicle 237

Checking the engine oil level 5. Remove the cosmetic shield on the right hand side of the engine compartment by unscrewing the screws shown in the figure, then remove the filler cap A, remove the dipstick F and check the Warning level: the level must be between the MIN and MAX notches on The engine oil level must be checked when the engine is idling the dipstick. and warm and the vehicle is on level ground. DO NOT add oil with different characteristics from those of the Important note oil already in the engine. The distance between the MIN and MAX notches corresponds to approximately 1.5 litres of oil. The symbol, shown below, on the left TFT display and the message “Check engine oil level” inform the driver that the engine oil level 6. If the level is low, top up with the recommended oil and make must be checked. sure you do not fill beyond the MAX level on the dipstick. Warning Proceed as follows: If the oil level is below MIN, top it up and then have the system 1. Run the engine until the engine oil temperature has reached 85 - checked by the Ferrari Service Network. 90 °C (185 - 194 °F). 2. Leave to idle for at least 4 minutes. 3. Run the engine at between 4000 and 4500 RPM for 1 minute. 4. Leave to idle for 2 minutes and then (before the 3rd minute elapses) check the oil level. A Important note F If the oil is checked after 3 minutes, repeat stages 3. and 4. and check the level again. 238 Care of the vehicle

7. Screw cap A back on tightly. Checking the DCT gearbox oil level After topping up, the “low oil level” symbol on the left TFT display may remain on for some time. This will allow the system to perform Important note all the necessary checks. You should therefore consider this behaviour normal. We recommend that you have the oil level of the DCT gearbox 8. When you have added or changed the oil, check the oil level checked by the Ferrari Service Network or by skilled staff. once again as indicated above. Important note The first check was performed between the 2nd and 3rd minute and the second check must therefore be performed within the same interval of time. For example, if the first check was performed after 2 mins 30 seconds, the second check must also be performed after approximately 2 mins 30 seconds. Environment Top up with due care to avoid pouring the oil out of the filler neck. 5 Care of the vehicle 239

Checking the coolant level Checking the power steering system oil level Warning Warning The coolant in the cooling system reaches very high The power steering oil level must be checked with the engine temperatures and pressures. This procedure must always be warm, after having driven at least 15 km (9 mi). If it is checked performed when the ENGINE IS COLD. Never remove the cap when the engine is cold, the level may appear to be very low from the expansion tank when the engine is running or warm. even when the recommended amount of oil is in the system. • Remove the cosmetic shield on the right hand side of the engine compartment by unscrewing the screws indicated in the figure, and Warning check that the level is as indicated by the dotted line in the figure. • If the level is low, remove the cap D from the expansion tank and If the oil level is below MIN, top it up and then have the system top up with the recommended fluid. checked by the Ferrari Service Network. Important note Proceed as follows: If frequent top-ups are required after short trips, have the • Remove cap E with the dipstick from the tank. system checked by the Ferrari Service Network. • Screw cap D back on tightly. E D 240 Care of the vehicle

• Check that the power steering oil level is between the MIN and Checking the brake fluid level MAX levels on the dipstick. Proceed as follows: • If the level is near the MIN reference mark, top up with the recommended oil up to the MAX level. • Remove the cosmetic shield on the left-hand side of the engine compartment by unscrewing the screws shown in the figure and check that the level is near the MAX mark shown in the figure. Warning Always use the indicated quantity of new, recommended fluid Important note taken from sealed containers. If frequent top-ups are required after short trips, have the The fluid in the circuit is synthetic. The use of mineral-based system checked by the Ferrari Service Network. fluid may irreparably damage the rubber system gaskets. • If the level is near the MIN mark shown in the figure, remove • Screw cap E back on tightly. cap B and top up with the recommended oil to the MAX mark. Environment Warning Do not dispose of used fluid in the environment. Always use the indicated quantity of new, recommended fluid taken from sealed containers. 5 MAX B MAX MIN MIN Care of the vehicle 241

Checking windscreen and headlight washer fluid levels Warning The windscreen and headlight washer fluid tank can be accessed by The fluid in the brake system may damage plastic, rubber and lifting the engine compartment lid. painted parts and is highly dangerous if it comes into contact • Lift cap C and fill the tank with the recommended fluid (see with the eyes or the skin. the “Refilling” table on page 35) until it can be seen in the fluid If the fluid comes into contact with the eyes or skin, wash the filling manifold. affected part thoroughly with running water. To avoid any risk, • Close cap C. always use protective goggles and gloves. Keep out from children's reach! Warning The use of mineral-based fluids will irreparably damage the system rubber gaskets. Do not use fluids other than those already in the system for topping up. Environment Do not dispose of used fluid in the environment. C • Screw the cap B back on tightly. 242 Care of the vehicle

Wheels and tyres Low tyre pressure can lead to overheating, internal damage and even destruction of the tyres. To ensure maximum performance and tyre life and to permit the best tyre adjustment on the wheel rim, it is important to comply with the following instructions for the first 200/300 km (125 - Warning 185 mi) with new tyres: Inflating the tyres to a pressure other than that prescribed will • avoid sudden acceleration render the TPMS monitoring system inaccurate. • avoid sharp braking and steering • drive at moderate speed on straight roads and on curves. Sudden impact with pavements, potholes and other obstacles of various types as well as long trips on rough roads can cause damage to the tyres that is not always visible to the naked eye. How to use the tyres Check the tyres regularly for any signs of damage (e.g. scratches, cuts, cracks, bulges, etc.). Important note If sharp objects penetrate the tyres, they can cause damage which is To ensure safe driving, the tyres must be kept in good condition. only visible when the tyre is removed. Have any damage inspected by an expert as it may considerably The inflation pressure must correspond to the specified values and reduce tyre life. must be checked only when the tyres are cold since tyre pressure Remember that tyres deteriorate over time even if they are rarely increases as tyre temperature increases. used or not used at all. Never reduce the pressure if the tyres are hot. Environment Cracks in the tread and side walls, possibly accompanied by bulging, are sure signs of ageing. 5 Periodically check the tyre pressure. Driving with the tyres inflated to the correct pressure helps to reduce fuel consumption. Care of the vehicle 243

Warning Warning The Ferrari Service Network has the necessary equipment for “Directional” type tyres have an arrow on their side wall to tyre replacement. indicate the direction in which they must rotate or which side is Have the tyres replaced by the Ferrari Service Network which the outer one. When replaced, maximum performance levels can has the equipment needed to avoid damage to the sensor inside only be ensured if the rotation direction corresponds with the the wheel rim which could be caused by carelessly performed direction indicated by the arrow. procedures. Tyres on the same axle must always be replaced in pairs. Ensure that tyres are not kept in stock for more than 4 years. The maximum limit for keeping tyres in stock is 4 years Regularly check the tyre tread (minimum acceptable depth provided they are kept away from sunlight, bad weather and 1.7 mm). As the tread wear increases, there is a greater risk of damp and where there is a low oxygen content. skidding. Important note Warning Drive carefully on wet roads to reduce the risk of “aquaplaning”. The Ferrari Service Network can certify whether aged tyres are suitable for use. In any case, tyres that have been on a vehicle for more than 3 years must be checked by a Ferrari Service Centre. Wheel alignment check and adjustment When you notice unusual wear of the tyres and in any case, at the intervals prescribed in the “Warranty Booklet”, have the Ferrari Warning Service Network check the wheel toe-in and camber. We recommend replacing tyres every 4 years under normal use. Frequent use in maximum load conditions and at high temperatures may accelerate ageing. 244 Care of the vehicle

Maintenance of seat belts and pretensioners Cleaning the vehicle • Periodically check that the screws on the anchor points are tight Cleaning the exterior and that the seat belt is in perfect condition and slides smoothly. • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. Environment • To clean the seat belt, wash it by hand with mild soap and water, All the materials used for the following operations (e.g. cloths rinse it and let it dry. Do not use strong detergents, bleach or soaked with oil or grease, pans, etc.) must be disposed of in aggressive solvents, as they can weaken the fibres. compliance with the environmental protection regulations. • Do not let the seat belt retractors get wet: proper functioning is only ensured if they are kept dry. Proper care of the vehicle on the part of the owner is essential for • The pretensioner requires no maintenance or lubrication. If the vehicle long life. immersed in water or mud, the pretensioner must necessarily be Here is a list of the main precautions to be taken. replaced. • Certain parts of the vehicle should not be left wet or dirty for • The pretensioner must be replaced at the intervals indicated in long periods of time: in particular, the passenger compartment the “Warranty Booklet”. floor and the luggage compartment must always be kept clean and dry. The draining holes under the doors should be kept unclogged to allow any water to drain. • The underbody and the lower surfaces of the vehicle should be cleaned regularly, and more frequently (at least once a week) if the vehicle is used on salty or rough roads. The vehicle should be cleaned thoroughly and carefully: cleaning that merely 5 wets encrusted mud without removing it completely can prove damaging. • The vehicle must be washed regularly with suitable equipment. Do not use very hot water or steam to clean the paintwork and the lower surfaces. It is advisable to soften any dirt first, then remove it with a jet of water at room temperature. Care of the vehicle 245

Cleaning and care of matt paintwork (optional) Important note Do not use aggressive products for cleaning the windows. Warning The use of aggressive products could seriously damage the The paintwork MUST NOT be polished using any type of bodywork. product. • Do not wash the vehicle in direct sunlight or when the bodywork Owners must take great care of vehicles with matt paintwork is still warm: make sure that the jet of water does not blast the (optional). paintwork; wash the vehicle with a sponge and a mild soap and water solution; rinse the vehicle again with a jet of water and dry Here is a list of the main precautions to be taken. it with a chamois leather. • Wash the vehicle using a steam cleaner and rinse with demineralised water only. Important note • It must be dried using an automatic dryer or compressed air. Manual drying can ONLY be performed using a 3M microfibre When the vehicle has been washed, apply slight pressure to the yellow cloth that is clean and soaked in demineralised water in brake pedal at moderate speed before driving at a normal speed, the areas where limescale deposits are present. The cloth must be until the brake discs and pads have cleaned off. kept in a special clean container. • To clean any grease or oil marks, a 3M microfibre yellow cloth In order to maintain the shine on the paintwork, polish it once or that is clean and soaked in R107/S solvent (heptane) can be used. twice a year with products recommended by Ferrari. A new cloth must be used and it must not have been previously • Any areas that are cracked or chipped by stones, scratches or soaked in demineralised water. parking manoeuvres, etc., must be immediately repaired by the • Do not wash the car in direct sunlight. Ferrari Service Network. • Wash the vehicle only when the bodywork and engine are cold. • Do not park the vehicle in damp and/or unventilated areas for long periods of time. • Do not apply stickers to the bodywork. 246 Care of the vehicle

• Any areas that are cracked or chipped by stones, scratches or parking manoeuvres, etc., must be immediately repaired by the Important note Ferrari Service Network. Avoid the film coming into contact with the brake fluid: the film will become opaque. Important note DO NOT lean against the vehicle especially if you are wearing • Do not use solvents along the edges of the film to them from clothes with buttons, buckles or are wearing rings, necklaces, penetrating inside the adhesive layer. etc. This may cause irreparable damage to the bodywork. Important note Important note Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Light Blue, Met Sky-Blue and Fuji White vehicles must be To use suitable products, contact the Ferrari Service Network. washed every month and waxed at least twice a year so that dirt, acid rain, pollutants, etc. do not penetrate the pores of the film and cause it to tarnish. Cleaning of protective antistone-chipping film (optional) The film has been designed to protect the bodywork: anything that damages the paint will also damage the film. Important note We recommend that the film be replaced every 24 months for Warning Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Do not pour denatured ethyl alcohol, acetone, isopropyl alcohol, heptane or substances that contain these compounds on the Light Blue, Met Sky-Blue and Fuji White vehicles, which may show a light visible tarnish due to dirt inside the pores of the film. 5 film. It should be noted that timely and accurate cleaning (monthly • Do not apply adhesive elements on the film. washing and waxing twice a year at least) will prevent deterioration • When cleaning, do not use metal or abrasive substances in general of the film. and acid chemical compounds. Care of the vehicle 247

Cleaning the interior Cleaning and care of the Alcantara® upholstery Cleaning and care of the leather upholstery Warning As indicated in the “Maintenance Schedule” (see the “Warranty Do not use steam cleaners. Booklet”), proper and regular treatment, at least once a year, will help preserve the quality, natural characteristics and softness of the • Carefully dust the parts to be cleaned leather upholstery in your Ferrari. • Use a soft cloth or sponge moistened with clean water With this in mind, specific leather care products are also available (“Cleaner” and “Cream”) both tested by Ferrari. • Thoroughly wring out the cloth and wipe it over the entire Alcantara® area making sure you do not overwet it These products can be ordered through the Ferrari Spare Parts Service Department, both individually and as part of the “Care Kit” • Repeat the procedure which includes the complete range of products for cleaning the • Let it dry completely vehicle. • To recondition the material, gently use a brush with soft bristles. Important note For use of the “Care Kit” products, contact the Ferrari Service Network. The following products must be avoided when cleaning the leather: harsh detergents, turpentine, liquid stain removers, petrol, solvents and domestic cleaning products damage the natural material. 248 Care of the vehicle

If the vehicle is stored for long periods If the vehicle is not used for long periods of time, certain precautions should be taken: • if possible, park the vehicle on a level surface in a covered and well-ventilated area • prevent the vehicle from moving by engaging a gear • bring the tyre pressure to 3.0 bar (43.51 psi) and periodically change the point where the tyres rest on the ground • connect the battery conditioner Important note If you do not want to connect the battery to the battery conditioner in order to keep certain devices functioning such as radio station memory, alarm system, etc., the battery must be recharged at least once a month. If the vehicle is not used for long periods of time without connecting the battery conditioner, the battery must be recharged at least every three months. • protect the vehicle with a breathable fabric cover and avoid materials that prevent any dampness on the bodywork from 5 evaporating. Before using the vehicle again after long periods of inactivity, adjust the tyre pressure to the indicated pressure and check the fluid levels of all the systems. Care of the vehicle 249

Glossary............................................................... 253

6 GLOSSARY

Abbreviation Meaning ABS (Anti-lock Braking System) The ABS prevents wheel locking when braking so that vehicle handling can be maintained. AC Air conditioning. ASR (Antriebs Schlupf Regelung) Anti-skid regulation during acceleration. Auto easy exit Simplified function gear shifting. To exit “Auto easy exit” mode, simply operate one of the two shift paddles. Autopark Automatic activation of the electric parking brake (EPB) when the engine is switched off. This function can be disabled. AVH Automatic Vehicle Holding Additional function of the electric parking brake (EPB): it allows gradual release of brake shoes/pads when the vehicle starts up. This guarantees an optimised release for the vehicle and is an aid for the driver. DCT Dual Clutch Transmission Each clutch is associated with a part of the gearbox, one is designed for engaging even gears, the other for odd gears. Once a gear has been engaged, the system has already preselected the next one. After reaching the correct RPM, a clutch opens and at the same time the other one closes, so that the traction force is not interrupted. Disposal The procedure laid down in Directive 2000/53/EC and the implementation standard. E-Diff 3 Evolved electronic differential integrated with the F1-Trac traction control. EBD (Electronic Brake-Force Distribution) Electronically-controlled brake-force distribution. ECU Electronic Control Unit. EPB ESC Electric Parking Brake: the system operates by means of an ECU and an electric motor on the rear brake shoes. Electronic Stability Control 6 Consists of two systems: VDC and F1-Trac. Glossary 253

Abbreviation Meaning F1-Trac Traction control derived from the technologies used in the racing sector. The system can estimate the maximum available grip in advance by continuously monitoring the relative wheel speed and using an auto-adaptive operating logic. Comparing this information with the vehicle dynamics model stored in the control system, F1-Trac, optimises the vehicle behaviour by controlling engine torque delivery. FBP (Ferrari Brake Prefill) System that eliminates the distance between the brake pads and discs by applying slight pressure to the braking system as soon as the accelerator pedal is released just before braking. This results in more immediate brake response. Homologation The procedure laid down in Directive 2007/46/EC and the implementation standard. Launch Control Strategy for performance standing starts. Manettino The driving mode control switch on the steering wheel that allows the driver to use vehicle potential in a quick, intuitive way. Park Lock Automatic DCT gearbox park lock. When the engine is off, a mechanical lock is automatically activated to prevent the vehicle from moving if the electric parking brake is not activated. TFT displays Multifunction colour displays on the instrument panel that provide vehicle information. TPMS Tyre Pressure Monitoring System. Using special sensors fitted inside the wheel rims next to the air valve, the data measured is sent to an ECU. The data and messages are displayed on the left TFT display. Traction power Force exerted by the vehicle on the road surface through the wheels; it indicates the grip. VDC Vehicle Dynamic Control performed through the braking system and engine torque. Xenon headlights Headlights on the front of the vehicle that produce a more intense beam by using a voltaic arc rather than an incandescent spiral. 254 Glossary

6 Glossary 255

Table of Contents................................................. 258

7 TABLE OF CONTENTS

Index B Basic seat ......................................................................................... 178 Battery .............................................................................................. 220 Battery conditioner ..................................................................... 224 Simboli Before a trip ................................................................................... 144 12V power socket ........................................................................ 195 C A Calibrating the TPMS system ...................................................  69 Capless filler neck ..........................................................................  84 Activating Cruise Control ......................................................... 130 Carwash procedure ....................................................................  164 Active Brake Cooling .................................................................. 176 CCM active brake cooling system ........................................ 176 Active safety .....................................................................................  43 Chassis and bodywork maintenance ................................... 235 Adaptive headlights (optional) .............................................. 142 Checking the battery .................................................................. 220 Adjusting display brightness .....................................................  91 Checking the brake fluid level ............................................... 241 Adjusting the air vents ..............................................................  189 Checking the coolant level ...................................................... 240 Adjusting the steering wheel .................................................  183 Checking the DCT gearbox oil level ................................... 239 Air conditioning and heating system .................................  186 Checking the engine oil level ................................................. 238 Alarm system ....................................................................................  15 Checking the power steering system oil level ................. 240 Auto easy exit ................................................................................ 150 Checking windscreen and headlight washer “Auto easy exit” mode ................................................................ 150 fluid levels ....................................................................................... 242 Auto Hazard ................................................................................... 141 Chronometer ....................................................................................  96 Automatic gearbox ...................................................................... 150 Chronometer screen page ..........................................................  96 “Automatic gearbox” mode ..................................................... 150 Cleaning and care of matt paintwork (optional) ........... 246 Automatic Vehicle Holding .....................................................  163 Cleaning and care of the Alcantara upholstery ............... 248 “Automatic Vehicle Holding” AVH function ...................  163 Cleaning and care of the leather upholstery .................... 248 Autopark .........................................................................................  163 Cleaning of protective antistone-chipping film Autopark function .......................................................................  163 (optional) ........................................................................................ 247 Auxiliary Occupant Protection Systems ...............................  50 Cleaning the exterior ................................................................. 245 258 Table of Contents

Cleaning the interior .................................................................. 248 Driving at night ............................................................................. 152 Cleaning the vehicle ................................................................... 245 Driving in fog ................................................................................ 153 Clutch overheat alarm devices ............................................... 226 Driving in the rain ....................................................................... 152 CODE CARD ...................................................................................  14 Driving mode control switch “Manettino” ........................ 132 Collapsible space saver spare wheel (optional) .............. 215 Driving modes that can be selected Consumption and CO2 emissions ..........................................  28 with “Manettino” .......................................................................... 133 Controls on the steering wheel ............................................. 132 Driving on mountain roads ..................................................... 153 Controls overview ..........................................................................  74 Driving on snowy or icy roads ............................................... 153 Cruise Control ............................................................................... 130 Driving the vehicle ...................................................................... 144 CT OFF mode ............................................................................... 158 Driving using the driving mode control switch (“Manettino”) ................................................................................ 156 D Driving with the “ABS” braking system ............................. 154 Date and time setting ...................................................................  92 Dual View Camera (optional) ................................................ 120 Day lights ......................................................................................... 140 Duplicating the keys .....................................................................  16 Deactivating the anti-lift volumetric alarm ............... 18, 143 E “Digital speed” screen page ..................................................... 118 Dimensions and weights .............................................................  27 Electrical system .............................................................................  28 Disconnecting the battery ........................................................ 220 Electric parking brake ...............................................................  162 Display setting and configuration Electronic alarm .............................................................................  17 of vehicle parameters ...................................................................  90 Electronic rev counter ............................................................... 115 Dome light ...................................................................................... 143 Emergency opening of fuel filler flap ...................................  83 Doors ...................................................................................................  78 Emergency release of the electric parking brake “Doors, engine or luggage compartment lid open” (EPB) ................................................................................................ 228 indication ........................................................................................  108 Emergency starting ..................................................................... 222 DOWN-shifting ............................................................................. 148 Emergency tyre repair and inflation kit ............................. 200 “DOWN” shift paddle ................................................................ 135 End-of-life vehicle collection service ....................................  11 Driver and passenger airbags ...................................................  51 Driver’s seat position memory (Full Electric option) ..  180 Engine compartment lid .............................................................  80 Engine malfunction alarm devices ....................................... 227 7 Table of Contents 259

Engine RPM LED on steering wheel (optional) ............ 115 G ENGINE START .......................................................................... 132 Environmental protection ..........................................................  10 Gearbox display ............................................................................ 116 EPB - Electric parking brake .................................................  162 Gear engaged ................................................................................ 116 “ESCAPE” function ...................................................................  106 General remarks ................................................................................ 4 ESC OFF mode ............................................................................ 158 Glossary ........................................................................................... 253 Exhaust system overheating alarm devices Glove compartment ....................................................................  193 (“Slow Down” function) ........................................................... 225 External rear-view mirrors ......................................................  184 H Hazard warning lights ............................................................... 141 F Headlight washer ......................................................................... 136 Failure of turn indicators and running lights .................. 107 High beams .................................................................................... 138 Fault display ..................................................................................  106 Horn .................................................................................................. 134 Ferrari CODE ..................................................................................  15 How to fasten seat belts ..............................................................  46 Flashing the headlights ............................................................. 138 Follow me home ........................................................................... 142 I Front “LIFT” system (optional) ............................................ 174 Identification and homologation plates and labels .........  20 Front parking sensors ................................................................ 143 If the vehicle is stored for long periods ............................. 249 Fuel filler flap and neck ..............................................................  83 Ignition switch ................................................................................  77 Fuel inertia switch ............................................................... 59, 219 Infotainment system ................................................................... 122 Fuel level gauge ..............................................................................  93 Infotainment System controls on the steering wheel ... 129 Fuses .................................................................................................. 207 Instruments and gauges ..............................................................  86 Internal rear-view mirror .........................................................  184 260 Table of Contents

K N Key codes ..........................................................................................  14 N (Neutral) ..................................................................................... 149 Key Lock ...........................................................................................  77 O L Oddment storage compartments ..........................................  194 LAUNCH button ......................................................................... 165 Launch Control ............................................................................ 165 P Left TFT display .............................................................................  88 Parcel shelf ...................................................................................... 191 Level checks ................................................................................... 236 Parking lights ................................................................................. 139 Light bulbs ..................................................................................... 205 Parking sensor failure ................................................................ 105 Lighting ............................................................................................ 138 Parking sensors ............................................................................  102 Light switch .................................................................................... 138 Park Lock .......................................................................................  164 List of left TFT display symbols Park Lock emergency release ................................................. 230 and warning lights on the panel ..........................................  109 Partition between passenger compartment Locking and opening the doors from the inside .............  78 and luggage compartment ......................................................  192 LOCK/UNLOCK button ...........................................................  78 Passenger compartment accessories ....................................  193 Luggage compartment lid ..........................................................  81 Passenger display (optional) ................................................... 121 M Passive safety ....................................................................................  42 Performance .....................................................................................  28 MAIN button ...................................................................................  88 PIT SPEED ..................................................................................... 130 Main engine specifications .........................................................  28 Placing luggage in the luggage compartment .................  190 MAIN screen page .........................................................................  88 Power steering system ................................................................ 154 Maintenance schedule ............................................................... 234 Power windows ...............................................................................  85 Manettino status screen page ...................................................  99 Pretensioners ...................................................................................  48 Manually activating and deactivating Stop&Start .......... 167 MENU screen page .......................................................................  90 7 Table of Contents 261

R S RACE mode ................................................................................... 157 Safe driving .................................................................................... 151 Racing seat (optional) ................................................................ 181 Satellite alarm system (optional) ............................................  19 Rain sensor ..................................................................................... 137 Seat adjustment ............................................................................ 178 Rear fog lights ............................................................................... 141 Seat belt and pretensioner care ...............................................  49 Rear Parking Camera (optional) ........................................... 119 Seat belts ...........................................................................................  44 Rear-view mirrors .......................................................................  184 Service ................................................................................................... 8 Reconnecting the battery ......................................................... 221 Side airbags ......................................................................................  56 Refilling ..............................................................................................  35 Speed limit setting and “Speed limit exceeded” Refuelling the vehicle ..................................................................  36 message ............................................................................................ 101 Replacing a fuse ..........................................................................  206 “Speedometer” screen page .................................................... 118 Replacing a wheel ........................................................................ 215 SPORT 2 screen page ..................................................................  94 Replacing brake pads ................................................................. 228 SPORT mode ................................................................................ 156 Replacing number plate light bulbs ...................................  203 SPORT screen page ......................................................................  94 Replacing other light bulbs ....................................................  204 Start button .................................................................................... 132 Replacing remote control batteries ........................................  17 Starting and driving the vehicle ............................................ 145 Replacing the front and rear light bulbs ..........................  203 Starting the engine ...................................................................... 146 Right TFT display ........................................................................ 118 Starting the vehicle ..................................................................... 147 Roof light unit controls (for HELE version) ................... 173 “Stop and Go” function ...........................................................  102 Roof panel controls ..................................................................... 143 Stopping the vehicle ................................................................... 149 Run Flat tyres (optional) ............................................................  34 Stop&Start system (optional) ................................................  166 Running-in ...................................................................................... 144 Sun visors .......................................................................................  193 Suspension damping control .................................................. 155 Suspension damping delink button ..........................  134, 160 Switching off the engine ........................................................... 149 System start-up ............................................................................. 145 262 Table of Contents

T W Tool kit ............................................................................................  198 Warming up the engine ............................................................. 147 Toolkit ..............................................................................................  198 “Warning: danger of ice” message ........................................ 100 TPMS failure ....................................................................................  70 Warning lights on the panel ...................................................  109 TPMS - Low pressure ..................................................................  66 Warranty Booklet ....................................................................  7, 234 TPMS - Tyre puncture .................................................................  67 WET mode ..................................................................................... 156 Transmission ratios ........................................................................  28 Wheel alignment check and adjustment ............................ 244 TRIP A and TRIP B screen pages ........................................ 100 Wheel rims and tyres ....................................................................  29 Turn indicators .............................................................................. 140 Wheels and tyres .......................................................................... 243 Twilight sensor .............................................................................. 140 Windscreen washer ..................................................................... 136 Tyre inflation pressure .................................................................  30 Windscreen washer/wiper ....................................................... 135 TYRES screen page ......................................................................  95 Windscreen washer/wiper lever ............................................ 135 Tyre temperature and pressure monitoring system (TPMS) ..............................................................................................  65 U Unfastening the seat belts ........................................................... 47 UP-shifting ...................................................................................... 148 “UP” shift paddle ......................................................................... 135 V VDA button ......................................................................................  88 VDA (Vehicle Dynamic Assistance) screen page group . 95 Vehicle Dynamic Assistance .......................................................  95 Vehicle keys ......................................................................................  14 Vehicle status screen page ..........................................................  97 7 Table of Contents 263

264 Table of Contents

Equipment and options in Ferrari vehicle models may vary because of specific legal and market requirements. The information contained in this publication is therefore not binding in any way. Ferrari reserves the right to make any modification to the vehicle models described in this manual, at any time, for either technical or commercial reasons. Contact the nearest Ferrari Dealer for any further information you may require. In the interests of efficiency and safety, as well as to preserve the value of the vehicle, we do not recommend modifying the equipment using non-approved parts.

Code no. 85173600 Catalogue no. 4283/12 Edition 2nd Edition November 2012 Editing STAR s.r.l. Alessandria - Italia Printing STAR s.r.l. Alessandria - Italia Technical Service Department Via Abetone Inferiore, 4 41053 Maranello Modena - Italia