Ferrari California Owners Manual

Thursday, August 31, 2017
Download

Owner's manual

General remarks This vehicle, which complies with EC homologation parameters, - Driving takes place in a naturally dangerous context where a uses advanced technology and is capable of achieving high number of different risk factors interact. For this reason, it is performance levels. important to drive bearing in mind that others, whether they are pedestrians, motorcyclists or motorists, can make mistakes. It is equipped with sophisticated active and passive safety Keeping a safe distance allows emergency measures to be systems (described below); these features and systems do not taken. authorise the driver to take risks other than those involved Distractions and underestimating danger are the cause of in normal driving since their preventive and protective action most accidents. is guaranteed only in certain conditions. Unless otherwise - Caution and discipline are the basis of safe driving. Correct instructed specifically by Ferrari (see the Safety chapter), and careful use of a vehicle derives, above all, from respect the deactivation of any of the vehicle’s restraint systems is for one's own safety and that of others as well as complying PROHIBITED. with road regulations. Only this respect will help you While certain safety devices (e.g. the airbags) have been tested experience all the emotions that driving this car can offer to ensure that they offer the highest possible levels of safety, you. they may nonetheless be hazardous in the event of failure by the driver or passenger to observe the instructions given by Ferrari recommends reasonable and careful use of the Ferrari. All occupants of the vehicle must be attentive at all vehicle. The driver MUST NEVER allow passengers to increase times and take particular care when transporting passengers the risks associated with driving (e.g. by not using safety who are more susceptible to injury, such as children, disabled systems such as seat belts) by failing to observe the mandatory and elderly persons. safety rules that apply to both driver and passengers. For safe driving, the following conditions must ALWAYS be met: The vehicle MUST NOT be modified or tampered with for - the driver must be in perfect psycho-physical condition; any reason whatsoever since, by so doing, the manufacturer's - road regulations (Road Regulations - Vienna Convention homologation and safety parameters will be modified. on Road Traffic that ended on 8 November 1968) must be The owner of the vehicle is obliged to perform careful strictly observed; maintenance on the vehicle in compliance with the - common rules of caution must always be observed in relation recommended maintenance schedule. to the quality/performance of the vehicle, driving conditions and contingent situations. •4

General remarks The driver must pay the utmost attention to the signals of the Remember that national and international legislation requires vehicle and, in particular, the warning lights on the dashboard that the driver of the vehicle must be capable of executing and buzzers. Even when the warning lights do not indicate corrective and/or emergency manoeuvres at all times. The a situation of immediate danger, the driver must be adopt a driver must also use any on-board information, communication cautious attitude towards possible consequences/degeneration and entertainment systems responsibly, especially when the of the failure and other information given. vehicle is in motion. Examples of information, communication Even during routine operations, such as refuelling, precautions and entertainment systems are as follows: satellite navigation should always been taken and it is important to check that systems, traffic information systems (e.g. ITT), media players flammable liquid has not been spilled; these cautions must (e.g. iPod), telephones with Bluetooth connectivity, etc. be observed even if the operation is performed by others. (whether merely audio-based or with display). Similarly, before setting off make sure that the doors are closed by checking the warning lights and also manually. The driver must bear in mind that on-board systems may be The driver must be fully acquainted with the vehicle and its a cause of distraction when driving since they may require controls in order to handle and drive it correctly. Acquaintance the driver to turn his or her attention away from the road for with the vehicle can be achieved/improved by attending several seconds. the driving courses held by Ferrari which we strongly Aftermarket video entertainment systems for the passenger (e.g. recommend. TV) must be installed where they cannot distract the driver while the vehicle is in motion. The use of motor sports terms (such as F1, SPORT and RACE) is merely indicative of the competition-derived technology These systems may only be operated by the driver: and suspension systems in the vehicle and does not endorse - in complete safety (stopping the vehicle before use if inappropriate behaviour on the road which does not comply necessary); with Traffic Regulations. - putting road safety first; for example, in poor or limited visibility, looking at a display with activated programmes can The above is merely a general outline of some of the problems be distracting if you take your eye off the road even for a described in detail in the rest of this manual. split second. •5

While the vehicle is in motion, the attention required to use on-board systems must never exceed the high level of attention required to drive safely in accordance with the Traffic Regulations; - ensuring, if the previous vehicle owner has installed systems on the vehicle that are NOT APPROVED by Ferrari (car tuning), that they are fully compatible with the original vehicle equipment; - in some countries, the use of entertainment/information systems is prohibited on vehicles when driving. The driver is responsible for use of these entertainment/ information systems with video screens if they are prohibited in the country where the vehicle will be driven. Strict priority criteria must be used when driving a vehicle: you must not therefore take your attention and eye off the road excessively in order to perform driving operations. Operations that do not concern driving (e.g. changing dashboard functions), must be performed in maximum safety when the vehicle is stationary. •6

Introduction The aim of this Owner’s Manual is to help you get the best Warranty Booklet value from your vehicle and to provide information on routine Each new vehicle comes equipped with a “Warranty Booklet”. maintenance: we advise you to read it carefully before setting out. The Owner's Manual should be considered an integral part This contains the vehicle’s warranty validity conditions. of the vehicle and must therefore always be kept on board. This warranty does not affect the buyer's statutory rights as Using the vehicle in a way that does NOT comply with a consumer, which derive from binding legal norms in his or the Owner's Manual not only exonerates Ferrari of any her favour, in the various states or countries or from European responsibility but also puts the person at great risk. Union regulations, towards the Dealer. The Warranty Booklet also contains the routine maintenance Updating indicated in the “Maintenance Schedule” The high quality level of the vehicle is subject to constant technological improvements. Therefore, there may be differences between this manual and your vehicle. Service The Ferrari Sales and Service Network will be pleased to The information in this manual is necessary for the use and provide you with all the information on any updates. proper care of the vehicle. In addition, Customers will get maximum satisfaction and results from the vehicle if they All specifications and illustrations contained in this manual carefully follow the instructions in it. refer to those resulting as of the printing date. We recommend you have all the checks and services performed Spare parts at Ferrari Authorised Workshops since they have highly skilled staff and the necessary equipment. When replacing parts or topping up with lubricants and fluids, Please refer to the “Sales and Service Organisation” manual we recommend you use original spare parts and the lubricants for information on the location of the Ferrari Dealers and and fluids recommended by Ferrari. Authorised Service Centres. The Ferrari warranty is voided if Original Ferrari Spare The Ferrari Technical Service Department is at your Parts are NOT used for repairs. complete disposal for any information and advice. •7

Consulting the manual To facilitate reading the manual, the topics have been divided Within the various sections, special attention must be paid to into sections and chapters. the parts marked as follows: To further facilitate consultation, each section is identified by a specific colour: General Warning Provides general information about your vehicle. Extreme caution required: failure to comply with the instructions could constitute a serious risk to personal safety Quick reference guide and vehicle protection! Contains all the information you need when using the vehicle for the first time. Important note Safety Describes the main safety systems in the vehicle. Important note: a note containing instructions or information. About your Vehicle Provides all necessary information for use of the vehicle. Environment Advice for Emergency Situations Warning for environmental protection: useful advice for protec- Provides useful advice for solving problems that may occur. tion of the environment. Care of the vehicle Provides advice for cleaning, care and routine maintenance of your vehicle. Glossary Explains the main technical concepts. Table of Contents Allows you to quickly identify and locate the information required. •8

DCT gearbox Abbreviations/Acronyms Some descriptions and terms with particular meanings are Important note found in this manual in an abbreviated form: The vehicle is equipped with an electro-hydraulically controlled A.C. Air-conditioning gearbox system by means of paddles on the steering wheel. ABS Anti-lock Braking System The default setting for the DCT gearbox is always “Automatic” ASR Anti-skid Regulation during acceleration mode. EBD Electronic Brake-force Distribution Every time the vehicle is started, the DCT gearbox is in “Auto CST Stability and Traction control easy exit” mode unless the vehicle was in “Automatic” mode when it was turned off. ECU Electronic Control Unit F1-Tractraction control derived from the technologies used in To exit the “Auto easy exit” mode operate the UP or DOWN the racing sector paddle (while the vehicle is moving) or press the AUTO button on the central console. Launch strategy for a high performance standing start. DCT Dual Clutch Transmission Important note For an overview of the abbreviations contained in this manual, Although the system can be used in “Automatic” mode, it should please see the Glossary. not be considered an automatic gearbox and therefore, to use it correctly, always follow the instructions given in this manual on page 154. •9

Environmental protection Driving style - Do not accelerate during the starting procedure. Environment - Do not warm up the engine when the vehicle is stationary. - Drive prudently and keep a safety distance suited to the driving The following chapter contains useful advice for environmental speed. protection. - Avoid sharp and frequent accelerations. - Turn off the engine if the vehicle is kept stationary for long peri- Ferrari has designed and constructed a vehicle using technologies, ods of time. materials and devices capable of reducing the harmful impact on the environment to a minimum. - Shift gears using only 2/3 of the speed permitted for each gear. Using your vehicle with respect for the environment will be your contribution towards environmental protection. Fuel consumption as well as engine, gearbox, brakes and tyres wear Important note mainly depend on two factors: The vehicle is equipped with exhaust gas control and monitor- - use of the vehicle ing systems which must be always kept in full efficiency and - driving style. controlled regularly. Both factors are influenced by the driver. Use of the vehicle - Avoid using the vehicle for short trips. - Check that the tyre pressure is correct. - Check the fuel consumption. - Proper periodic maintenance will contribute to preserving your vehicle in full working order and to protecting the environment. We therefore advise you to respect the service due dates indicated in the “MAINTENANCE SCHEDULE”. • 10

End-of-life vehicle collection service For many years, Ferrari has been globally committed to respect- ing and protecting the environment by constantly improving its manufacturing processes and developing increasingly eco-compat- ible products. To ensure that its customers receive the best service possible, in compliance with environmental legislation and the requirements of EU Directive 2000/53/EC for end-of-life vehicles, Ferrari offers owners the possibility of consigning their end-of-life vehicles at no additional cost so that it can be disposed of. The EU Directive states that the final owner of an end-of-life vehicle (ELV) must be able to consign his or her vehicle without incurring any costs as a result of its null or negative market value. In almost all European Union member states, since 2007, ELV collection is free of charge regardless of the year of registration pro- vided that the vehicle (and the engine and bodywork in particular) contains no additional waste. To consign your end-of-life vehicle at no additional cost, please contact one of our dealers to ensure that the vehicle is collected, processed and recycled properly without harming the environment. • 11

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Vehicle keys Important note The vehicle is delivered with two identical keys that can be used for: Make sure you record the code numbers in the space provided in the “Warranty Booklet”. - central door locking; - starting the vehicle; Key codes - deactivating the alarm system; - activating/deactivating the alarm; A CODE CARD is supplied with the keys. This card shows the following: - opening the luggage compartment. - the electronic code - the mechanical code for the keys, to be given to the Ferrari Important note Service Network if you request duplicates of the keys. If the keys are lost or stolen, you can request a duplicate from the Ferrari Service Network (see section “Duplicating the Warning keys” on page 16). The code numbers on the CODE CARD must always be kept in a safe and protected place, not accessible to others. Important note In the event of a change of ownership, it is essential that the new vehicle owner is provided with all the keys and with the CODE CARD. 1 • 14 · General ·

Alarm system 1) If the code is recognised, the CODE warning light A on the instrument panel turns off when checking has terminated The Ferrari CODE system whereas the EOBD warning light B turns off when the engine is started once the ECU has completed its diagnostic cycle; In The vehicle is equipped with an electronic immobiliser system these conditions, the protection system has recognised the key (Ferrari CODE) which is automatically activated when the ignition code and deactivated the immobiliser. key is removed. 2) If the CODE warning light A stays on, it means that the code The keys are equipped with an electronic device which transmits has not been recognised. In this case, it is advisable to turn the a coded signal to the Ferrari CODE ECU. Once this ECU has key back to position 0 and then back to II. If the immobiliser recognised the signal, it allows starting the engine. device remains active, try with the other key provided. Operation Each time the ignition key is removed from the 0 position, the Important note protection system activates the engine immobiliser. If you still cannot restart the engine, contact the Ferrari - When starting the engine, press the ENGINE START button on Service Network. the steering wheel: � � · General · 1 • 15

- While driving, with the ignition key in position II: 1) If the CODE warning light A turns on, it means that the system Important note is performing a self-diagnostic cycle. At the first opportunity, you Contact the Ferrari Service Network immediately to have all can stop and test the system: switch off the engine by turning the keys stored in the system memory. the ignition key to position 0, then turn the key back to position II. The CODE warning light A will turn on and should go off within one second. If the warning light stays on, repeat the Important note procedure described previously leaving the key at 0 for more than 30 seconds. Each key supplied has its own specific code, which must be stored in the memory of the system control unit. Important note If the problem persists, please contact the Ferrari Service Duplicating the keys Network. If you request additional keys, provided that the conditions to satisfy your request are met, remember that the codes must be 2) If the CODE warning light A flashes, it means that the vehicle is stored (up to a maximum of 7 keys) on all the keys. not protected by the immobiliser. Contact the Ferrari Service Network directly and bring the following with you: - all the keys in your possession; - the CODE CARD for the Ferrari CODE system; - a personal identity document; - the documents proving ownership of the vehicle. The codes of the keys that are not available when the new memorisation procedure is performed will be deleted from the � memory, in order to prevent that any lost or stolen keys are used to start the vehicle. � 1 • 16 · General ·

Replacing remote control batteries Electronic alarm If you press one of the three buttons of the key and this does not The electronic alarm system performs the following functions: activate the corresponding function, check for correct operation of - remote control for central door locking/unlocking; the alarm system functions using the other remote control before replacing the batteries. - perimeter surveillance, detecting if doors and lids are opened; Replace the remote control batteries as follows: - motion surveillance, detecting intrusion into the passenger compartment; - lever open the key cover C with a small screwdriver at the position - vehicle movement surveillance. indicated by the arrow; - remove the battery D pushing in the direction indicated by the Activation arrow to release it from the retainer cover E; To activate the electronic alarm, press button F on the key: - fit a new battery of the same type, observing the indicated polarity; - the direction indicators flash once; - close the key cover C. - the system “beeps” Important note - the red LED on the dashboard flashes - the central door locking system is activated and the doors are locked. Do not use sharp tools to remove the cover and be careful to avoid damaging the remote control. The system activates after approximately 25 seconds. When the electronic alarm is activated, the user may request opening of the luggage compartment; in this case, the motion and anti-lift sensors are temporarily deactivated. � � � � � · General · 1 • 17

If the luggage compartment is then closed, the sensors will be The alarm system is off and it is therefore possible to get into the reactivated. vehicle and to start the engine. The direction indicators and the red LED on the dashboard should If the remote control battery is flat, to gain access to the vehicle, be flashing 9 times when you activate the alarm system: this means insert the key into one of the two door locks, then turn it to release that one of the doors or the front/rear lid is open or not properly the lock. The alarm siren will start to sound. closed and therefore is not protected by the perimeter surveillance. Start the vehicle following the standard procedures. The alarm siren Check for correct closing of the doors, front/rear lid and close will deactivate. the open door or lid without deactivating the alarm system: the direction indicators flashing once indicate that now the door or the front/rear lid is closed properly and is protected by the perimeter surveillance. Deactivating the anti-lift alarm Press button H to deactivate the anti-lift alarm system. When this Warning function is deactivated, the LED on the button will flash for about 3 seconds and will then turn off. If the direction indicators and the red LEDs on the dashboard flash 9 times when the alarm system is activated with doors, rear and front lids properly closed, it means that the self-diagnostic feature has detected a malfunction in the system. Contact the Ferrari Service Network to have the system checked. Deactivation To deactivate the alarm system press button G on the key: - the direction indicators flash twice; - the system beeps twice; - the red LED on the dashboard switches off; � - the dome lights and the lights under the doors turn on; - the central door locking system is deactivated and the doors are unlocked. Pressing button G twice unlocks the doors and also turns on the low beams for 30 seconds. 1 • 18 · General ·

Alarm memory Ministerial homologation If the CODE warning light appears on the display when the vehicle The electronic alarm system complies with EU regulations on elec- is started, this means that an intrusion has been attempted. tromagnetic compatibility and it is marked in compliance. The alarm system memory is reset by turning the ignition key. The homologation number is referred to with the following charac- ters. In this case, the system will indicate the reason for the alarm activation according to the following priority: For those markets that require the transmitter and/or receiver marking, the homologation number is found on the component. - LED off twice: lifting sensor alarm - LED off three times: door alarm Satellite alarm system (optional) - LED off four times: luggage compartment lid alarm The vehicle can be equipped, upon request, of a satellite alarm - LED off five times: ignition key alarm. system. For information refer to the booklet “Quick Reference Nav The alarm system memory is reset by turning the ignition key. Trak”, if the vehicle is equipped with satellite alarm system, in the vehicle documents. · General · 1 • 19

Identification and homologation plates and labels A Assembly number plate B Low beam homologation label � � � � C Homologation and ECE label D Fuel label E Paintwork label � F Oil check label � � G Engine/gearbox oil type label � � H TPMS present label � I Anti-freeze label L Vehicle identification plate � M Warning label prohibiting child seat � installation � N Airbag maintenance label � O Airbag warning label P Engine type and number � Q Tyre pressure and type label R Gearbox type and number S Chassis number plate T Retractable hard top warning labels � � � � 1 • 20 · General ·

A Assembly number plate C Homologation and ECE label B Low-beam homologation label D Fuel label · General · 1 • 21

E Paintwork label G Engine/gearbox oil type label F Oil check label H TPMS present label 1 • 22 · General ·

I Anti-freeze label M Warning label prohibiting child seat installation L Vehicle identification plate N Airbag maintenance label · General · 1 • 23

O Airbag warning label Q Tyre pressure and type label P Engine type and number R Gearbox type and number 1 • 24 · General ·

S Chassis number plate T Retractable hard top warning labels · General · 1 • 25

Dimensions and weights Wheelbase 2670 mm (78.74 in.) Max. length 4562 mm (157.48 in.) Max. width 1909 mm (75.15 in.) Max. height 1322 mm (52.04 in.) Front track 1630 mm (64.17 in.) Rear track 1605 mm (63.18 in.) Front overhang 952 mm (37.4 in.) ���� ���� Rear overhang 940 mm (37 in.) Kerb weight (DCT) 1780 kg (3916 lb.)* ���� * considering the most favourable OPT combination ���� ���� ���� 1 • 26 · General ·

Main engine specifications Transmission ratios Type F 136 IB Gearbox Differential/bevel gear pair Number of cylinders 8 ratios ratio Cylinder sequence V 90° 1 = 2.822 Cylinder bore 94 mm 2 = 2.053 Piston stroke 77.4 mm 3 = 1.379 4.444 Total displacement 4297 cm3 4 = 1.091 Compression ratio 12.2:1 5 = 0.966 Maximum RPM 8000 RPM 6 = 0.788 (with limiting device) 7 = 0.651 Max. power 338kW R = 2.368 (Directive 1999/99/EC) (460 HP) Corresponding RPM 7750 RPM Performance Max. power 485 Nm (Directive 1999/99/EC) 0 - 100 km/h 0 - 400 m Max. speed Corresponding RPM 5000 RPM F1 3.9 s 12.2 s > 310 km/h Electrical system Consumption and CO2 emissions Supply voltage Alternator EC Directive 1999/100 l/100 km g/km 12 V Nippondenso 150 A SC2 City cycle 19.4 443 Battery Starter motor Motorway 9.4 215 Fiamm 12V - 100 A/h - 850 A Nippondenso Average fuel 13.1 299 consumption · General · 1 • 27

Wheel rims and tyres Wheel rims Front Rear Spare wheel 8” J x 19” 10” J x 19” 4.5” J x 20” 8” J x 20” 10” J x 20” 4.5” J x 20” Tyres approved by Ferrari Inflation pressure (cold) Front Rear Spare wheel Front Rear Spare wheel Pirelli P Zero 245/40 ZR19 285/40 ZR19 145/60 ZR20 2.40 bar 2.20 bar 4.20 bar Bridgestone 245/40 ZR19 285/40 ZR19 145/60 ZR20 2.40 bar 2.20 bar 4.20 bar Michelin 245/40 ZR19 285/40 ZR19 145/60 ZR20 2.40 bar 2.20 bar 4.20 bar Optional tyres Inflation pressure (cold) Front Rear Front Rear Pirelli P Zero 245/35 ZR20 285/35 ZR 20 2.40 bar 2.20 bar Bridgestone RE 050 (Run Flat) 245/40 ZR19 285/40 ZR19 2.40 bar 2.20 bar Bridgestone 245/35 ZR20 285/35 ZR20 2.20 bar 2.20 bar Winter tyres Inflation pressure (cold) Front Rear Front Rear Pirelli Winter Sottozero 245/40 ZR19 285/40 ZR19 2.40 bar 2.20 bar 1 • 28 · General ·

Correct tyre reading Example: 245/40 ZR 19 245 = Nominal width (distance in mm from side to side) 40 = Height/width ratio as a percentage Z = tyre that can support speeds of over 240 km/h R = Radial tyre 19 = Diameter of rim in inches The tyre manufacture date is included in the description of the tyre: DOT ... 1008 means that the tyre was manufactured in the 10th week of 2008. Correct rim reading Example: 8” J x 19” 8 = width of rim in inches J = shape of rim flange (side projection where the tyre bead rests) 19 = rim diameter in inches (corresponds to the diameter of the tyre to be fitted) For further information on the tyres, see page 226. · General · 1 • 29

Run Flat tyres (optional) The vehicle can come equipped with “Run flat” tyres. This type of Warning tyre has a reinforced side A which allows the vehicle to continue If you are going to use standard tyres on a vehicle that was travelling at moderate speed originally equipped with “Run Flat” tyres, you must contact (80 km/h), even after a puncture, for a specific distance. the Ferrari Service Network to have the dashboard The instrument panel receives the “tyre puncture” information from reprogrammed and to prevent viewing warning messages on the the tyre pressure monitoring ECU, monitors the residual tyre life, TFT display. and displays a warning in the dedicated area of the TFT display after 50 km. After 100 km, a message warning the driver to stop the vehicle will be displayed (see “Tyre pressure and temperature monitoring system” on page 87). Warning Observing the recommended wheel alignment values is essential in order to obtain the best performance and the longest life of these tyres. � 1 • 30 · General ·

Refilling Parts to be refilled Quantity Fill with: Ref. Page Engine Total system capacity 11 l HELIX ULTRA SAE 5W-40 221 Oil level between Min. and 1.5 l Max. Oil consumption 1.0 ÷ 2.0 l/1,000 km Gearbox and differential 4.9 l TRANSAXLE 75W-90 GL5 223 Clutch system and hydraulic controls 9.2 l DCT-F3 Braking system -l DONAX UB BRAKE FLUID 225 DOT4 Ultra Cooling circuit -l GLYCOSHELL at 50% 223 Hydraulic steering system -l DONAX TX 224 Steering box -g Fuel tank 78 l Unleaded fuel 95 RON. 104 Reserve 20 l RHT system Total system capacity 0.4 l Pentosin CHF 11S - Oil level between Min. and Max. 65 ml Air conditioning and - heating system Compressor 165 cc PAG ISO 46 Coolant 500 ± 50 g DELPHI RL 488 “R 134 A” Windscreen washer/headlight washer fluid tank -l Mixture of water and glass cleaner 226 · General · 1 • 31

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Opening Locking and opening the doors from the inside Both doors are locked by activating/deactivating button A on the Doors dome light. When the doors are opened or closed, the windows will When using the handle to open the door, the window will move automatically move down approximately 2 centimetres (0.8 in.) down to its “target position”. When the door is closed, it will move and stop (broken line) in order to prevent collision with the door up until it meets the “upper weather strip”. weather strip. If the handle is operated without opening the door, the window When the door is closed, the window automatically moves up until will move down to its “target position” and stop, and if the door is it meets the upper limit (weather strip). not opened after 15 seconds, the window will move back up until it meets the “upper weather strip”. Opening from the outside Therefore, the handle must be released and pulled again in order Using the remote control, deactivate the alarm and the central door to open the door. locking system, or turn the key in the lock to deactivate the central When the opening handle is operated, both doors are unlocked. door locking system. When pulling the handle to open the door, the window moves Underdoor light down approximately 2 centimetres. When the door is closed, it will Each door has an underdoor light. This light comes on automatically move back up until it meets the upper limit. when the door is opened. � 2 • 34 · Quick reference guide ·

Retractable hard top The preliminary steps for opening and closing the retractable hard top are: - vehicle must be stationary Warning - luggage compartment must be closed For safety reasons, the retractable hard top can only be opened - battery voltage must not be below 11 volts and closed when the vehicle is stationary. - partition between luggage compartment and folded roof compartment must be in the correct position, fully pushed back and fastened Warning - check there is adequate space heightwise and in the rear of the vehicle: the minimum available height A must be 1700 mm, the The roof must be opened or closed whilst remaining correctly minimum distance B of an obstacle from the rear must be more seated in the driver's seat. than 400 mm - ignition key in position II and engine running. Warning Important note Before activating the roof and while it is in motion, always check that people and objects are at a safe distance from the moving We recommend operating the retractable hard top with the parts of the roof. In the event of danger, release the roof switch; engine running. all movement will stop immediately. - no overheating of hydraulic system. Warning Before operating the retractable hard top, make sure that the backrest of the child restraint system is set to its minimum height. � Important note If distance B is less than 400 mm, the parking sensors will not allow the roof to open or close. � · Quick reference guide · 2 • 35

If one or more conditions are not met, the following message will At the end of the opening cycle, an acoustic signal will indicate the appear on the TFT display. end of operations and the corresponding message will appear on the TFT display (see page 112). Important note Important note Before opening or closing the hard top, refer to “Placing suitcases in the luggage compartment” on page 177. Throughout all these phases, the side windows cannot be activated. Roof opening using switch For further information, see pages 111-112. Warning Roof closing using switch Before opening the roof, ensure that the top of the roof and Push forward the switch A on the central console and hold until the the rear screen are dry to avoid water entering the passenger operation has been completed. compartment or luggage compartment. The operation in progress will be indicated by a message on the TFT display. Pull back the switch A on the central console and hold until the At the end of the closing cycle, an acoustic signal will indicate the operation has been completed. end of operations and the corresponding message will appear on The operation in progress will be indicated by a message on the the TFT display (see page 113). The switch can be released. TFT display (see page 112). For further information, see pages 112-113. � � 2 • 36 · Quick reference guide ·

Controls overview � � � Ref. Control Page 1 Adjustable air vents 175 2 Glove compartment 176 3 Hazard warning lights control 47 4 Door opening handle 102 5 Light switch 117 � � � � · Quick reference guide · 2 • 37

� � �� Ref. Control Page 6 “ENGINE START” button 146 7 “Manettino” control 146-164 8 Rev counter and “DOT MATRIX” display 144 9 “TFT” display 122 10 Speedometer 109-144 � � 2 • 38 · Quick reference guide ·

�� Ref. Control Page �� �� �� �� 11 Ashtray 176 12 Power window controls 106 13 “R” reverse control (*) 157 14 “Launch” control (*) 166 �� �� 15 “AUTO” control (*) 159 16 Air conditioning and heating system controls 173 17 Retractable hard top closing control 111 · Quick reference guide · 2 • 39

Adjustments Lumbar support and side width adjustment Use control F to adjust the lumbar support. Seats Use control G to pneumatically adjust the width of the backrest Correct adjustments are very important for a better driving comfort sides and the seat cushion. and for the maximum efficiency of the passive safety systems. For further information, see page 168. Warning Never adjust the seat while driving; you may lose control of the vehicle. Adjust the driver’s seat only when the vehicle is stationary. The seat position can be electrically adjusted using the special controls. Three adjustments are possible using control E: forward/backward, height, inclination (tilting). For further information, see page 167. Seat back rake adjustment For further information, see page 168. � � � 2 • 40 · Quick reference guide ·

Tilting the backrest Headrest adjustment To tilt the seat, pull lever L up and push the backrest towards the To lower the headrest, press button M. front of the vehicle. Place the headrest at a height that corresponds to the height of the For further information, see page 169. occupant. To raise the headrest, simply pull it up. Warning Seat heating system (optional) For further information, see page 170. Backward/forward adjustment must allow for the fact that airbag devices are placed in front of the driver and the front passenger (see page 74). Driver’s seat position memory (optional) Correct adjustment ensures there is adequate space between the This device allows you to memorise and recall three different seat airbag and the person (see page 74). positions. For further information, see page 168. � � · Quick reference guide · 2 • 41

Steering wheel Rear-view mirrors The steering wheel is electrically adjustable for rake and reach. It can only be adjusted if the ignition key is in position II. Internal electrochromic mirror Move control A (to the left of the steering column) in the four The internal electrochromic mirror automatically darkens to reduce directions to adjust the steering wheel. the dazzling effect of the reflected light on the driver. The speed The steering wheel position is memorised, together with the with which the mirror darkens depends on the intensity of the light. position of the external rear-view mirrors, when the driver’s seat position is stored. External rear-view mirrors These mirrors can be electrically adjusted using the control B (with Warning the ignition key in position II) and are equipped with defogging Do not adjust the steering wheel while driving. elements. 1) Mirror selection: using control B select the mirror you wish to adjust (right- or left-hand). To help the driver when entering or exiting the vehicle, the steering wheel is lifted automatically. 2) Mirror positioning: move control B in the four directions (up – down – right – left) to adjust each mirror. � 2 • 42 · Quick reference guide ·

Once adjustment is complete, move the control B into the upper Seat belts central position, where it will be locked, in order to avoid changing the setting inadvertently. Warning The mirrors will yield in both directions in the event of a collision: if necessary, the mirrors can be pushed both backwards and The seat belts must be properly adjusted and buckled at all forwards. times! Correct use of the seat belts can reduce the risk of serious injury Warning in the event of an accident or if the vehicle overturns. The mirrors must be always positioned correctly while driving. Do not adjust the mirrors when the vehicle is moving. Do not use any devices (spring clips, locks, etc.) that could keep a seat belt from fitting properly. Fastening the seat belts After positioning the seat correctly; • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it out, let it wind back briefly and pull it out again without jerking). � � � � � � · Quick reference guide · 2 • 43

• Make sure that it has clicked into the locked position. • Position the seat belt correctly. Warning Do not allow children to be held on a passenger’s lap using only Warning one seat belt for both of them. To position the front seat belt correctly, make sure that it passes through the loop C, as shown in the figure. Warning If the driver’s seat belt is not fastened, when you turn the ignition Remember that, in the event of a violent impact, passengers key to position II, the warning light on the instrument panel lights in the rear seats who are not wearing seat belts are not only up and remains lit as long as the seat belt is not fastened. subject to personal injuries (they can be catapulted forward, hit the windscreen and be thrown out of the vehicle) but also constitute a danger to the passengers in the front seats. Unfastening the seat belts • Push the release button E. Refer to the “Safety” chapter on page 60. • Guide the latch plate A back to its rest position. � � � 2 • 44 · Quick reference guide ·

Driving Warning Ignition switch Never remove the key when the vehicle is moving! The ignition key can be turned to 2 positions: The steering wheel will lock on the first steer. Always remove the key from the ignition when you get out of Position 0 - Stop the vehicle! Engine off, key removable. Never leave children unattended in the vehicle. When the key is even only partially extracted, the steering column is locked. The hazard warning lights and the parking lights can be activated. To facilitate steering wheel release, turn the steering wheel slightly in both directions while turning the ignition key. Position II - Ignition Turning the key to this position, the TFT display will check the signals coming from the vehicle systems. If no malfunctions are found after starting up, the words “Check OK” will be displayed. �� � · Quick reference guide · 2 • 45

External lights and direction indicators Important note Light switch Follow the Road Regulations of the country you are travelling in Switch A has five positions: for using the high beams. 0 Lights off Flashing the headlights Running and number plate lights on The headlights can be flashed by pulling the left-hand lever B Low beams on towards the steering wheel. Parking lights AUT Automatic operation of the external lights according to the ambient light. High beams To turn on the high beams when the light switch A is set to , push the left-hand lever B towards the dashboard. Pull the lever B towards the steering wheel again to turn off the high beams and turn on the low beams. � � 2 • 46 · Quick reference guide ·

Direction indicators Rear fog lights When lever B is: The rear fog lights are turned on only if the high beams or low - moved up, the right-hand direction indicators are turned on; beams are on when button D is pressed. - moved down, the left-hand direction indicators are turned on. The lever returns to the neutral position automatically when the Important note steering wheel is straightened. Use the rear fog lights only in poor visibility conditions. To indicate a temporary lane change, requiring only the slightest turn of the steering wheel, the lever can be moved without clicking Hazard warning lights it into position (non-permanent position). Press button A to turn on the hazard warning lights. All the direction indicators will start blinking intermittently. These lights will operate with the ignition key in any position. When the lights are on, the relative warning lights on the instrument panel and the button flash. To turn them off, press the button again. For further information, see page 120. � � � � · Quick reference guide · 2 • 47

Starting and driving the vehicle (DCT gearbox) If the warning light A is faulty, a warning light will appear on the TFT display (see page 143) and this condition will be indicated by System start-up an acoustic alarm when the ignition key is turned to position II. When the ignition key is turned to position II the DOT MATRIX gearbox display and failure warning light A are turned on. The Warning warning light will turn off if no problems are detected within a few seconds. Contact the Ferrari Service Network. The letter P (Parking) or N (Neutral) will remain highlighted on the display. Important note BEFORE YOU DRIVE If the warning light A continues flashing without going off, switch off the system and wait for the gear display to go off before restarting. If the failure persists, contact the Ferrari Service Network. � 2 • 48 · Quick reference guide ·

Operation with the engine off If the indication flashes (may also occur with N) it means that the gear is not perfectly engaged or disengaged; therefore, request N The vehicle is equipped with an electro-hydraulically controlled and then the desired gear. gearbox system by means of paddles on the steering wheel. The default setting for the DCT gearbox is always “Automatic” Important note mode. Every time the vehicle is started, the DCT gearbox is in “Auto easy Immediately release the UP and DOWN paddles and the button exit” mode unless the vehicle was in “Automatic” mode when it R after the display shows that the gear has been engaged; a was turned off. prolonged manoeuvre will cause the failure warning light to turn on (see page 142 “Generic failure”) and trigger the buzzer. To exit the “Auto easy exit” mode simply operate the UP or DOWN Do not operate the system with the engine off to prevent the paddles (while the vehicle is moving) or press the AUTO button on battery from discharging. the centre console. Also avoid unnecessary gearshifting when the engine is off, in Once the “System start-up” stage has been completed, the engaged order to prevent the system pump from overheating. gear will appear on the DOT MATRIX display: N (Neutral) P (Parking) R (Reverse gear) 1 (1st gear) 2 (2nd gear), etc. ���� �� · Quick reference guide · 2 • 49

• Press the ENGINE START button (see page 146) and release it Important note as soon as the engine starts. If the engine compartment lid is open or not properly closed, • After the engine has started, the “Check OK” will appear. none of the gears can be engaged. When the vehicle is Do not hold the ENGINE START button pressed down for a long stationary, with the driver-side door open or not properly closed time. and the brake pedal released, the system disengages the gear If the engine does not start, turn the key back to position 0 and engaged after approximately two seconds. wait for the gear display to go off before retrying. Starting the engine Warning • Make sure that the electric parking brake is applied and that the doors are closed. Hold the brake pedal down while starting the engine. • Hold the brake pedal down when starting the engine. If the engine fails to start after several attempts, check for one of Warning the following causes: • insufficient speed of the starter motor (flat battery) Do not press the accelerator pedal. • ignition device faulty • electrical contacts faulty • Turn the ignition key to position II and wait for the “Check OK” icon to appear on the TFT display. • fuel pump fuses blown. • If the “Check OK” symbol does not appear, turn the key back to position 0, wait a few seconds and repeat the procedure. • The vehicle is always in “Auto easy exit” mode, unless it was turned off with the gearbox in “Automatic” mode. 2 • 50 · Quick reference guide ·

Warming up the engine Do not run the engine at high speeds until the engine oil Important note temperature has reached at least 65-70 °C (149-158 °F), When the reverse gear is engaged, an acoustic safety signal approximately. beeps intermittently for the entire time the R remains engaged. Starting the vehicle If the system automatically selects 2nd gear when attempting to With the engine started, the vehicle standing and the brake pedal shift from R to 1st gear, this indicates that 1st gear has jammed. pushed, pull the right-hand “UP” paddle towards the steering Therefore, this is not a malfunction, as it falls within the system wheel to engage the 1st gear. operation logic. For the same reason, when shifting from 1st gear Release the brake pedal and press the accelerator to start off. to “R”, the system will automatically engage “N” if the gear has jammed. With the engine running and the vehicle stationary, you can change directly from 1st or 2nd gear to “R” (reverse) by pressing R and from During prolonged stops with the engine running, it is advisable to reverse to 1st by moving the “UP” paddle. keep the gearshift in “N”. Warning Important note If the “UP” and “DOWN” paddles are not working, the message On downhill stretches, if you allow the vehicle to move forward “Depress brake pedal and press LAUNCH to engage gear” will in “N”, when “UP” is requested, the system will engage a gear in appear on the TFT display. You can therefore engage the gear by relation to the vehicle speed. pressing the Launch button (see page 166) and the brake pedal. In these cases, the Launch control function is not available. If the engaged gear was R, the Launch button must be pressed twice to engage the 1st gear. · Quick reference guide · 2 • 51

UP-shifting Stopping the vehicle Operate the right-hand UP paddle without releasing the accelerator When the vehicle stops, the system automatically engages the 1st pedal. gear (unless “N” has already been requested). An UP-shift request is not accepted when engagement of the When the vehicle is stationary and the engine is running, hold the requested gear will force the engine to underrev or if an UP-shift is brake pedal down until ready to move off again. already in progress due to engine overrevving. For further information, see page 148. Turning off the engine and deactivating the system The engine can be switched off either with the gearbox in “N” or DOWN-shifting with a gear engaged. Use the left-hand “DOWN” paddle, even without releasing the After turning the ignition key from position II to position 0, the accelerator pedal. display will remain on for a few more seconds to display the A DOWN-shift request is not accepted if engagement of the engaged gear. If the gearbox is in “N” a buzzer will sound. requested gear forces the engine beyond a certain number of revolutions, depending on the gear requested, or if a DOWN-shift Warning is already in progress because of underrevving. Never leave the vehicle with the gearbox in “N”. Make sure that For further information, see page 148. the letter “P” appears on the display. “N” (Neutral) request For further information, see page 158. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. 2 • 52 · Quick reference guide ·

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Ferrari has designed and built a high performance vehicle. Emissions In order to take advantage of the safety systems described below, it is important to comply with the indicated regulations. Warning • The exhaust gas generated by the running engine may be Special warnings hazardous, especially when in closed spaces. As well as This vehicle has been built to comply with homologation, personal consuming oxygen, the engine discharges carbon dioxide, safety and environmental regulations. carbon oxide and other toxic gases. To this high safety standard must correspond a careful and cautious • The fuel is highly inflammable and emits vapours which may behaviour of the driver. be noxious if inhaled. Particular attention must be paid to: Do not use naked flames or create sparks near the open fuel • Overheated components. High temperatures develop in the tank or in any other condition where fuel comes into contact engine compartment in proximity of the exhaust system. Do not with air. park the vehicle on paper, grass, dry leaves or other flammable materials. They could catch fire if they come into contact with Lubricants hot parts of the exhaust system. Do not fit other heat shields or remove those fitted on the exhaust system. Do not let flammable Warning substances come into contact with the exhaust system. • Moving parts on the vehicle such as belts, fans, etc. They must • The oils used may also be flammable: take the same always be adequately protected. Do not remove the guards or precautions as adopted for the fuel. operate on the moving parts without taking due precautions. • Installations under pressure such as the braking system, the Flammable fluids air-conditioning system, the cooling system and the lubrication system may create pressures inside them. Do not carry out any Warning operation which may cause gas or liquids to spill out with the risk of injury to persons and damage to things. • The fluid in the battery is poisonous and corrosive. Do not let it spill out and come into contact with the skin, eyes or objects. Do not use naked flames or create sparks near the battery. Fuel inertia switch • See page 83. 3 • 56 · Safety ·

Warning Warning Seat belts must be worn at all times and must be properly Each seat belt has been designed to protect only one occupant. fastened and adjusted! If more than one person uses the same seat belt, the risk of Correct use of the seat belts can significantly reduce the risk injury in the event of an accident is increased. and severity of injury if an accident occurs or if the vehicle Do not sit babies, small children or other persons on your lap. overturns. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning For an effective restraining action, the seat belt must be fastened correctly with the seat backrest in the upright position. The seat belt is fastened correctly when the upper part of the belt crosses the centre of the shoulder (not the neck) and the abdominal section is fitted over the hips (not the stomach). Make sure it is not twisted and that it passes closely over your body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Avoid wearing bulky clothing that may interfere with the correct operating of the seat belts. Warning To increase driving safety, it is advisable to position the headrest so that the top is in line with the top of the head. · Safety · 3 • 57

Passive safety Warning The aim of the passive safety system is to reduce the risk and severity of injury if an accident occurs. The auxiliary safety systems are not a substitute for seat belts. The vehicle has the following seat belts: All occupants must always wear a seat belt. Correct use of the seat belts combined with use of the auxiliary safety systems 1. 3-point driver's seat belt with pretensioner and load limiting offers maximum protection to occupants in various types of device (see page 60) collision. 2. 3-point front passenger seat belt with pretensioner and load limiting device (see page 60) The vehicle also has the following auxiliary occupant protection and, only when rear seats are provided: system components (see also page 72 “Auxiliary occupant 3. 3-point rear passenger seat belt with pretensioner and load protection systems”): limiting device (see page 63) 5. front driver airbag (for operating functions see page 75) 4. 3-point rear passenger seat belt with pretensioner and load 6. front passenger airbag (for operating functions see page 75) limiting device (see page 63) 7. driver side head protection side airbag (head bag) (for operating functions see page 79) 8. passenger side head protection side airbag (head bag) (for operating functions see page 79) � � � �� � �� �� �� �� � � �� �� � � �� � 3 • 58 · Safety ·

9. active roll bars (for operating functions see page 81) The passenger compartment structure, on the other hand, has been 10. seats (see page 167) designed for maximum resistance without undergoing deformation, with the aim of ensuring a protective survival cell for the occupants. 11. deformable body 12. occupant protection system ECU Active safety 13. ECU auxiliary sensors The aim of the active safety system is to reduce the risk of accidents 14. instrument panel warning light (see page 74) and reduce the severity of injury. 15. inertia switch In addition to the features of the vehicle, manoeuvrability, stability and, only in the presence of rear seats (see also page 66 “Child and acceleration, there are other elements that can be considered as safety”): safety components: 16. a child seat lower anchorage system in the seat behind the front • braking system passenger • air conditioning and heating system 17. a child seat lower anchorage system in the seat behind the • external lights driver • buzzer and warning lights (flashing). The vehicle does not have upper anchorage systems for the The braking system includes the mechanical brake system and the installation of child seats. electronic stability and traction control system (ABS and EBD) which prevents the wheels from locking and always provides good Warning manoeuvrability and stability. The protective action of the airbags is always integrated with The possibility of fast acceleration can in some cases get you out the seat belts and the pretensioners. The compulsory use of the of dangerous situations. However, always use the accelerator with safety belt is provided by the national regulations (in Italy, for extreme caution. During acceleration of the driving wheels, the anti- example, by the Codice della Strada, i.e. Traffic Regulations). skid system may help you in certain dangerous situations. The air conditioning and heating system in the passenger Deformable body compartment can add to driving comfort and keep you alert so that you can react quickly when necessary. The deformable body absorbs shock and distributes it over the entire structure of the vehicle allowing progressive deceleration. It is very important to be able to clearly see the road and to be seen, hence it is essential to turn on the external lights when the conditions so require. · Safety · 3 • 59

Seat belts Statistics show that when used correctly, seat belts reduce the risk Warning of injury in various types of crashes including the risk of ejection For an effective restraining action, the seat belt must be fastened from the vehicle and impact with the interior of the vehicle. correctly with the seat backrest in the upright position. If left unfastened, seat belts offer absolutely no protection. Before The seat belt is fastened correctly when the upper part of the every trip, always make sure that all occupants are wearing their belt crosses the centre of the shoulder (not the neck) and the seat belts. abdominal section is fitted over the hips (not the abdomen). Make sure it is not twisted and that it passes closely over your Warning body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Seat belts must be worn at all times and must be properly fastened and adjusted! Avoid wearing bulky clothing that may interfere with the correct operating of the seat belts. Correct use of the seat belts can reduce the risk of serious injury in the event of an accident or if the vehicle overturns. The seat belts for the front seats have a lap-shoulder belt with an automatic emergency-locking retractor and are fitted with a pyrotechnic-powered pretensioner and an automatic system that reduces the force applied to the occupant. 3 • 60 · Safety ·

The seat belts for the rear seats have a lap-shoulder belt with an automatic emergency-locking retractor and are fitted with a Warning pyrotechnic-powered pretensioner and an automatic system that Do not attach or pin anything onto the seat belts: they may get reduces the force applied to the occupant. damaged and may consequently break in the event of a collision. Warning Warning To increase driving safety, it is advisable to position the headrest so that the top is in line with the top of the head. If a seat belt has come into contact with cutting edges or was somehow perforated, we recommend you have it immediately replaced by the Ferrari Service Network Warning Do not let the seat belts come into contact with cutting edges. They may get damaged and may consequently break in the Warning event of a collision. Periodically check the condition of the seat belts. If the belt shows signs of wear, it must be checked by a qualified person and replaced if necessary. Contact the Ferrari Service Warning Network immediately. Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not sit babies, small children or other persons on your lap. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. · Safety · 3 • 61

How to fasten seat belts • Make sure that it has clicked into the locked position: hold the belt and pull it to check that the latch plate has been inserted correctly. Warning • Position the seat belt correctly. For an effective restraining action, the seat belt must be fastened correctly with the seat backrest in the upright position. Warning The seat belt is fastened correctly when the upper part of the belt crosses the centre of the shoulder (not the neck) and the To position the front seat belt correctly, make sure that it passes abdominal section is fitted over the hips (not the abdomen). through the loop C, as shown in the figure. Make sure it is not twisted and that it passes closely over your body; if not, in the event of a head-on collision, it may move If the driver’s seat belt is not fastened, when you turn the ignition and cause injury to the abdomen. key to position II, the warning light D on the instrument panel lights up and remains lit until the seat belt is fastened. Avoid wearing bulky clothing that may interfere with the correct operating of the seat belts. 55 seconds after a speed of 10 km/h is exceeded, a buzzer sounds warning the driver that the seat belt is not fastened. Once you have adjusted the seat correctly (see page 167); When a speed of 20 km/h is exceeded, the buzzer activates immediately and stops after 90 seconds. • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it out, let it wind back briefly and pull it out again without jerking). � � � 3 • 62 · Safety ·

This acoustic signal is emitted only once, even if the vehicle speed Use of the rear seat belts goes above and below the above mentioned limits. It is repeated (valid only in the presence of rear seats) (when the vehicle speed is in the indicated ranges) only if the seat belt is fastened and unfastened again or, in any case, every time the engine is turned off and then on. Warning Only persons who are less than 1.50 m tall may travel in the Warning rear seats. The minimum distance between the head of the rear passenger Each seat belt has been designed to protect only one occupant. when seated correctly and the rear screen must be at least If more than one person uses the same seat belt, the risk of 2.5 cm. injury in the event of an accident is increased. Persons on the rear seat who are taller risk serious injury in the The seat belt must never be passed around a baby, child or event of an accident. other person sitting on a passenger's lap. Persons on the rear seat who are taller risk serious injury if the Do not sit babies, small children or other persons on your lap. retractable hard top is opened or closed. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning Unfastening the seat belts The retractable hard top MUST only be operated when no • Push the release button E. persons and/or children are occupying the rear seats. • Guide the latch plate A back to its rest position. � � � · Safety · 3 • 63

The rear seat belts must be fastened as shown in the diagram below Pretensioners Warning The seat belts for the front seats are fitted with pyrotechnic- powered pretensioners. The pretensioner is activated by the airbag Remember that, in the event of a violent impact, passengers ECU in the event of a head-on collision (impact direction between in the rear seats who are not wearing seat belts are not only 11 and 1 o'clock p.m.) of sufficient severity, or in a side collision of subject to personal injuries (they can be catapulted forward, sufficient severity. The pretensioner is also activated when there is hit the windscreen and be thrown out of the vehicle) but also a sufficiently severe rear collision or a roll-over (see page 60). The constitute a danger to the passengers in the front seats. belt will rewind a few centimetres just before the restraining action begins, thereby improving the fitting across the occupant's body. Activation of a pretensioner is signalled by the illumination of the warning light A on the instrument panel. Warning Pretensioners that have been activated will no longer function and may not be repaired under any circumstances. Contact the Ferrari Service Network for replacement. � 3 • 64 · Safety ·

When a pretensioner is activated, a small amount of smoke is • The pretensioner requires no maintenance or lubrication. released. This smoke is not harmful. If immersed in water or mud, it must be replaced. • Pretensioners must be replaced at regular intervals as indicated in Warning the “Warranty Booklet”. Activation of the pretensioners only depends on the status of the seat belts and is not affected by the occupants' presence. Important note If the seat belt is not fastened, the pretensioner will not activate, All work on any part of this safety system must be performed by even if the seat is occupied. the Ferrari Service Network. The seat belts for the front seats and any rear seats are fitted with a load limiting device. The load limiting device is located in the belt Warning winder and allows controlled release of the belt during a collision It is not permitted to remove or make modifications of any kind thereby limiting the impact that the belt has on the occupant's to the seat belts, belt retractors and pretensioners. body. Maintenance work involving strong impacts, vibrations or heating of the pretensioner area may activate them; vibrations Maintenance of the seat belts and pretensioners caused by road bumps will not have this effect. • Following a serious collision, replace the seat belts that were worn at the time even if they do not appear to be damaged. • Periodically check that the screws on the anchoring points are tight and that the belt is in perfect condition and slides smoothly. • The belt must be kept clean; the presence of any dirt could jeopardise the efficiency of the belt winder. • To clean the seat belt, wash it by hand with mild soap and water and let it dry. Do not use strong detergents, bleach or aggressive solvents, as they can weaken the fibres. Make sure the retractors do not get wet: proper functioning is ensured only if they are kept dry. · Safety · 3 • 65

Child safety Warning Warning The instructions in this Owner’s Manual ONLY apply to the Standard seat shown in the figure. Never leave children ALONE and/or unattended in the vehicle They do not apply to the Optional seat. since this may constitute a danger to themselves and others. In a number of countries, the transportation in vehicles of children and infants is governed by specific legislation and traffic regulations. Drivers are obliged to comply with applicable regulations. Warning This is an extreme sports vehicle. Do not use the vehicle to transport infants since sudden acceleration may cause injury. Warning Drive slowly and pay maximum care and attention when transporting children. Sudden acceleration caused by sports- style driving may be dangerous for children even if no collision �������� occurs. 3 • 66 · Safety ·

2-seater version You are therefore advised to ALWAYS use homologated child restraint systems that bear the proper test marking and check they comply with the ECE-R 44 standard. Child seats homologated Warning according to the ECE-R 44 standard bear the ECE-R 44 test Do not transport young children in rear facing child restraint marking (a circled E with the approval number underneath). systems on the front passenger seat unless absolutely necessary. Although the front passenger airbag has been designed and Warning developed not to cause injury, it should be stressed that the Incorrect fastening of a child restraint system increases the risk muscle and bone structure of infants is not fully developed and of injury to the child if an accident occurs. therefore vulnerable; the risk of very severe or even fatal injury caused by activation of the airbag cannot therefore be excluded. - The seat belts in the vehicle have been designed and tested to protect persons weighing at least 36 Kg and taller than 1.50 m. Warning - To properly protect children outside these limits, specific restraint systems with dedicated belts or accessories capable of adapting If you absolutely have to carry a child on the front passenger the child’s position to the vehicle seat belts must be fitted. seat in a rear facing child restraint system, the front passenger seat must be positioned as far back as possible with the sides of the seat as far open as possible and the lumbar support Warning adjustment as low as possible. The seat must also be adjusted For installation and use (how to secure the child to the restraint to the lowest position to enable the child restraint system to be system) of child restraint systems, follow the instructions that correctly installed. the manufacturer of the devices is obliged to provide. Because of their size, children are at greater risk than adults. Suitable restraint or safety systems must be used. All minors whose physical characteristics (i.e. height, weight) fall within the legal limits in force in each country must be protected by approved restraint or safety systems (e.g. child seats, cradles, cushions). · Safety · 3 • 67

- it is homologated. Child seats homologated according to the Warning ECE-R 44 standard bear the ECE-R 44 test marking (a circled E with the approval number underneath) Carefully follow the instructions provided with the child seat: keep them in the vehicle together with the documents - it is suitable for the height and weight of the child to be and this manual. Do not use second-hand child seats with no transported (CAREFULLY FOLLOW the instructions in the child instructions. restraint system use and maintenance manual) - it can be securely installed in the vehicle in compliance with the child restraint system manufacturer's instructions Warning - the use and installation instructions are easy to understand. Follow the instructions given by the child restraint system manufacturer when choosing, installing and using the restraint Warning system since failure to do so may compromise its protective action. If violent braking or a collision occurs, children who are not in a restraint system can be thrown against the dashboard or the windscreen: this may lead to serious or even fatal injury to the Warning child. Always check the seat belt have been securely fastened by pulling on the seat belt. Warning Never allow children to travel sitting in the lap of an adult. Warning If there is a collision, the adult's weight may crush the child against the seat belt or the dashboard: this may lead to serious After an accident, have all the parts of the child restraint system or even fatal injury to the child. and vehicle seat belt system checked and replace them if necessary. Any work must be performed at the Ferrari Service Network. Important note NO modifications must be made to the seat belts and child Children must always be transported in restraint systems that are restraint systems: any modifications may seriously jeopardise the suitable for their size. safety of the child restraint system. Before choosing a child restraint system, always check that: 3 • 68 · Safety ·

The front passenger seat does not have special hooks for child 2 + 2-seater version restraint systems. To transport a child, use the seat belts to secure the child restraint Warning system to the vehicle seat and make sure you have activated the automatic belt winding locking system before installing the child Do not transport young children in rear facing child restraint seat in the vehicle. systems on the front passenger seat unless absolutely necessary. To activate the automatic belt winding locking system, pull the Although the front passenger airbag has been designed and seat belt until the belt completely unwinds. At this point, the belt developed not to cause injury, it should be stressed that the retractor will only allow the seat belt to rewind. muscle and bone structure of infants is not fully developed and The fact that the belt cannot be pulled out confirms that the belt therefore vulnerable; the risk of very severe or even fatal injury locking system has been activated. caused by activation of the airbag cannot therefore be excluded. To deactivate the locking system, unfasten the seat belt in order to allow it to rewind completely. Warning Warning If you absolutely have to carry a child on the front passenger seat in a rear facing child restraint system, the front passenger Each time the belt is used to fasten a normal occupant, seat must be positioned as far back as possible with the sides the automatic belt winding locking system will have to be of the seat as far open as possible and the lumbar support deactivated. adjustment as low as possible. The seat must also be adjusted to the lowest position to enable the child restraint system to be correctly installed. Warning In countries where it is already a legal requirement, children Because of their size, children are at greater risk than adults. under 12 years of age may not travel in the front passenger seat. Suitable restraint or safety systems must be used. ALWAYS COMPLY with the legal requirements in force in your All minors whose physical characteristics (i.e. height, weight) fall own country. within the legal limits in force in each country must be protected by approved restraint or safety systems (e.g. child seats, cradles, cushions). Important note For child restraint systems that can be installed on the 2-seater version with 3-point seat belts, see TAB 1. pages 98-99. · Safety · 3 • 69

You are therefore advised to ALWAYS use homologated child restraint systems that bear the proper test marking and check they Warning comply with the ECE-R 44 standard. Child seats homologated Follow the instructions given by the child restraint system according to the ECE-R 44 standard bear the ECE-R 44 test manufacturer when choosing, installing and using the restraint marking (a circled E with the approval number underneath). system since failure to do so may compromise its protective action. Warning Incorrect fastening of a child restraint system increases the risk Warning of injury to the child if an accident occurs. Always check the seat belt have been securely fastened by - The seat belts in the vehicle have been designed and tested to pulling on the seat belt. protect persons weighing at least 36 Kg and taller than 1.50 m. - To properly protect children outside these limits, specific restraint Warning systems with dedicated belts or accessories capable of adapting the child’s position to the vehicle seat belts must be fitted. After an accident, have all the parts of the child restraint system and vehicle seat belt system checked and replace them if necessary. Warning Any work must be performed at the Ferrari Service Network. For installation and use (how to secure the child to the restraint system) of child restraint systems, follow the instructions that the manufacturer of the devices is obliged to provide. Children must always be transported in restraint systems that are suitable for their size. Before choosing a child restraint system, always check that: Warning - it is homologated. Child seats homologated according to the Carefully follow the instructions provided with the child ECE-R 44 standard bear the ECE-R 44 test marking (a circled E seat: keep them in the vehicle together with the documents with the approval number underneath) and this manual. Do not use second-hand child seats with no - it is suitable for the height and weight of the child to be instructions. transported (CAREFULLY FOLLOW the instructions in the child restraint system use and maintenance manual) 3 • 70 · Safety ·

- it can be securely installed in the vehicle in compliance with the child restraint system manufacturer's instructions Warning - the use and installation instructions are easy to understand. Before operating the retractable hard top, make sure that the backrest of the child restraint system is set to its minimum Important note height. NO modifications must be made to the seat belts and child restraint systems: any modifications may seriously jeopardise the The rear seats of the vehicle have an ISOFIX lower anchorage safety of the child restraint system. system (2 for each rear seat) (marked A in the diagram) that is placed under the special leather cover. The vehicle has no upper anchorage systems. Warning In countries where it is already a legal requirement, children Warning under 12 years of age may not travel in the front passenger seat. Before installing a child restraint system on the rear seats, the ALWAYS COMPLY with the legal requirements in force in your corresponding front seat must first be positioned as far forward own country. as possible with the backrest as upright as possible. Warning The retractable hard top MUST only be operated when no persons and/or children are occupying the rear seats. � � · Safety · 3 • 71

Auxiliary Occupant Protection Systems Warning If violent braking or a collision occurs, children who are Warning not placed in a restraint system can be thrown against the dashboard, windscreen or front seats: this may lead to serious or The Auxiliary Occupant Protection Systems are not a substitute even fatal injury to the child. for the seat belts but increase their efficiency. Correct use of the seat belts with the supplementary action of the Auxiliary Occupant Protection Systems, offers maximum protection in the Warning event of a head-on collision or vehicle roll-over. Never allow children to travel sitting in the lap of an adult. If there is a collision, the adult's weight may crush the child Auxiliary Occupant Protection System components against the seat belt, the dashboard or the back of the front seat: The Auxiliary Occupant Protection System components are: this may lead to serious or even fatal injury to the child. 1. Seat with built-in headrest and belt loop. 2. Dual-stage front driver airbag. Important note 3. Dual-stage front passenger airbag. For child restraint systems that can be installed on the 2 + 2- 4. Driver side head protection side airbag (head bag). seater version with 3-point seat belts and ISOFIX, see TAB 2. 5. Passenger side head protection side airbag (head bag). and TAB. 3. on pages 98-99. � � � � � 3 • 72 · Safety ·

6. Driver's seat belt (3-point with pretensioner and an automatic The airbags 1 and 2 have been designed to increase the level of system that reduces the force applied to the occupant). protection given by the seat belts in the event of a head-on collision 7. Front passenger seat belt (3-point with pretensioner and (see page 60). an automatic system that reduces the force applied to the The airbags 3 and 4 have been designed to increase the level of occupant). protection given by the seat belts in the event of a side-on collision 8. Rear seat passenger seat belt (3-point with automatic system and are placed between the occupant’s head and external structures that reduces the force applied to the occupant). which could go through the passenger compartment and cause injury (see page 78). 9. Rear seat passenger seat belt (3-point with automatic system that reduces the force applied to the occupant). The roll bars 10 have been designed to help maintain a survival area in the event of a roll-over (see pages 81-83). 10. Active roll bars Since it is impossible to gauge vehicle dynamics and movements of 11. Electronic Control Unit (ECU). the occupants in an accident, the active roll bars are also activated 12. Additional sensors. as a precautionary measure in the event of: 13. Instrument panel warning light. - sufficiently severe head-on collisions (that activate the front 14. Deformable body. airbags) if they have caused a cut-out of the fuel supply - sufficiently severe side-on or rear collisions. �� � � �� �� �� � � �� · Safety · 3 • 73

Warning Warning The warning light A comes on when the ignition key is turned The front airbags have been designed not to inflate if a minor to position II. If no malfunctions are detected, it goes out after collision occurs. The seat belts have been designed to reduce approximately 4 seconds. If the warning light does not come the risk of injury if a minor collision occurs. on, if it remains on or if it comes on while driving, contact the Ferrari Service Network immediately. Warning Driver and passenger airbags The driver and the passenger must maintain a distance of at least 25 cm from the steering wheel and the dashboard. Warning Always drive with your hands on the rim of the steering wheel so that in the event of activation, the airbag can deploy without The front airbags do not offer protection in the event of side- obstruction. on collisions, some head-on/angular collisions, roll-overs or Driving with your hands on the steering wheel spokes or on the subsequent collisions (if there is a second collision once the airbag cover increases the risk of injury for your wrists and arms. airbags have been deployed in an earlier collision). The seat belts have been designed to reduce the risk of injury in the event of a roll-over or subsequent collision. � ���� 3 • 74 · Safety ·

Warning Environment The front passenger must be seated correctly: never put When the system is activated, gases are released in the form hands, feet or legs on the dashboard since if the front airbag is of fumes, together with the gas used for inflating the airbags. activated, it may cause injury to the legs and prevent the airbag These gases are not harmful. from working properly. The driver's airbag has been designed to be deployed according Operation to the following strategy: The front airbags are controlled by an ECU which activates them • For low severity crashes, the airbag control unit will not deploy in the event of a head-on collision (direction of impact between the airbag. 11 and 1 o'clock p.m.) of sufficient severity. • For crashes of higher severity, the control unit will deploy the In the case of a collision with an impact force that causes driver airbag in low energy mode. deceleration exceeding the value set for the internal sensor, the • For crashes of even higher severity, the control unit will deploy ECU will transmit a signal to deploy the airbags. The airbags will the driver airbag in high energy mode. begin to inflate, breaking the cover along the breakage line and will deploy completely in a few tenths of milliseconds. Once deployed, The passenger airbag has been designed to be deployed they will serve as protection between the driver and/or passenger according to the following strategy: and structures that could cause injury. • For low severity crashes, the airbag control unit will not deploy The airbags deflate immediately afterwards. the airbag. • For crashes of higher severity, the control unit will deploy the Important note passenger airbag in low energy mode. • For crashes of even higher severity, the control unit will deploy If a head-on collision occurs that causes a cut-out of the the passenger airbag in high energy mode. fuel supply, the active roll bars will also be activated as a precautionary measure. Warning Even in vehicles with Advanced Airbag Systems, according to Warning statistics, the rear seats are the safest for transporting babies and The driver and passenger should not carry objects (drink cans or small children. bottles, pipes, etc.) that may cause injury if the airbags are activated. Children must always be transported on the rear seats if the Persons, animals or items must not be placed between the airbags vehicle has them. and the occupant. · Safety · 3 • 75

stationary if it is hit by a moving vehicle. Warning Remember that if the ignition key is set to 0 none of the safety The driver and passenger must always fasten their seat belts devices (airbags or pretensioners) is activated in the event of a and sit in an upright position, as far as possible away from collision; failure of the airbags to inflate in these circumstances is the airbag, in order to have optimal protection in all types of not indicative of a system malfunction. collision. Important note Warning Do not cut or tamper with the connectors of the airbag harness or on the airbag modules. Always keep the backrest of your seat in the upright position and sit with your back properly resting against it. Warning Important note Do not cover the steering wheel and the padded panel on the dashboard on the passenger’s side with adhesive tape or treat it Do not modify the system components or wiring, under any in any way. circumstances. With the ignition key inserted and in position II, although the Warning engine is off, the airbags can still be activated when the vehicle is Do not place objects above or near the top of the dashboard and the steering wheel. In the event that the airbags are deployed, these objects would be propelled into the passenger compartment at a high speed that would seriously jeopardise the safety of the occupants. Warning The airbag modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Booklet” even if the vehicle has NOT been involved in a collision. 3 • 76 · Safety ·

Warning Important note Do not modify the airbag modules in any way (indicated in The airbag system components have been specially designed the relevant diagram). Do not damage the airbag modules (for only for this specific vehicle model. Do not use them on a example pinning something onto them or pressing objects different vehicle model, as this may cause serious damage and against their covers). consequent injury, even fatal, to the occupants in the event of an If, for any reason, an airbag cover gets damaged, have the airbag accident. module immediately checked by the Ferrari Service Network. Activation of a damaged module could cause serious or fatal Warning injuries. Damaged or defective components of the airbag system cannot be repaired and must be replaced. Important note Improper operations performed on the system components may Do not remove or dismantle parts of the steering wheel, cause failures or accidental deployment or failure of the airbags dashboard or door panels; If necessary, this procedure should to inflate with consequent damage and injury, even fatal. only be performed by a Ferrari Service Network Centre. Environment Important note To scrap the vehicle, please contact the Ferrari Service All the airbag system components must be replaced after an Network to have the airbag system deactivated. accident that caused airbag deployment. Important note Following an accident not involving airbag deployment, contact the Ferrari Service Network to have the system checked and any system components that may be damaged or malfunctioning replaced. · Safety · 3 • 77

Head Airbags Important note If the vehicle has been stolen or there has been an attempted Warning theft, have the airbag system checked by the Ferrari Service Network. The airbags are not a substitute for the seat belts although they increase their efficiency. Correct use of the seat belts, with the supplementary action of the head bags, offers maximum Important note protection in the event of a collision or vehicle roll-over. The label E on the right-hand side of the dashboard, bears the airbag system expiry date. When this expiry date is approaching, Head bag system components contact the Ferrari Service Network in order to have the system replaced. Warning The head bag fitted on the vehicle was not designed to reduce The label F indicates the presence of the airbag system. the risk of being hurled out in the event of vehicle roll-overs. The vehicle has 2 head bags, one in the driver-side door and the other in the passenger-side door. � � 3 • 78 · Safety ·

The head bag system consists of 2 airbags, one on each door. In the roll bars (precautionary measure because of possible deformation event of a side-on collision, the airbag on the impact side deploys of the vehicle body that may affect deployment if there is a immediately to protect the occupants' head. subsequent roll-over. The airbag will start inflating, opening its cover along the breaking Warning line, until it is fully deployed (in a few hundredths of seconds). After deployment, the head bag will act as a protection between When the ignition key is turned to position II, the warning light the driver’s or passenger’s head and the external structures which B will come on. If no malfunctioning in the airbag system is could go through the passenger compartment and cause injury. The detected, it will go off after 4 seconds. If the warning light does airbags deflate immediately afterwards. not come on, if it remains on or if it comes on while driving, Head bag activation is not affected by the front passenger's height contact the Ferrari Service Network immediately. or weight. The side bag is activated whenever the airbag ECU detects a collision of a sufficient impact force for deployment. Operation The head bags are controlled by the ECU that activates them when Warning a sufficiently severe collision occurs. In the event of a side collision with a force of impact exceeding Never drive with your head out of the window as this places the limit set by the ECU, this will transmit a signal that activates your head and neck in the airbag deployment area. In the event the pretensioner, the head bag on the impact side and the active of a side-on collision, this position increases the risk of being thrown out of the vehicle and compromises the protective action of the head bags. � Warning Never place an object over or near the airbag covers. In the event that the airbags are deployed, these objects would be propelled into the passenger compartment at such high speed as to seriously jeopardise the safety of the occupants. · Safety · 3 • 79

Warning Important note Never modify the airbag modules. Do not damage the airbag The label E on the right-hand side of the dashboard, bears the modules and trim panels above them (for example, the area airbag system expiry date. When this expiry date is approaching, above the door panel) (by pinning something onto them or contact the Ferrari Service Network in order to have the pressing objects against their covers, for example). system replaced. If, for any reason, an airbag cover gets damaged, have the airbag module immediately checked by the Ferrari Service Network. Important note Activation of a damaged module could cause serious injuries. Never remove the door panel. If required, this operation must be performed by the Ferrari Service Network. Important note Please consider that the airbag ECU is not capable of automatically detecting damages involving the airbag covers. Do not cover the upper part of the driver-door and passenger- door panels with adhesive tape or material and do not treat them in any way. Warning After deployment, the airbag components can no longer offer any protection; therefore, they cannot be repaired and must be � replaced. After activation of a head bag, have it replaced by the Ferrari Service Network. Warning The airbag modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Booklet” even if the vehicle has NOT been involved in a collision. 3 • 80 · Safety ·

Roll bar Warning The active (ejectable dynamic) roll bar has been designed and installed to maintain the survival area of occupants in the event of a The active roll bars do not reduce the risk of ejection of vehicle roll-over. occupants who are not wearing seat belts or the risk of injury caused by impact with the interior of the vehicle in the event of The active roll bars are controlled by the ECU that activates them a collision or roll-over. when there is a strong roll around the longitudinal axis of the vehicle and there is a risk that the vehicle will roll over. Seat belts must always be fastened to reduce the risk of being thrown out of the vehicle and reduce the risk of injury caused In the case of a roll that exceeds the calibration thresholds, the by impact with the interior of the vehicle. ECU will release the roll bar locking system and deploy the roll bars in a few tenths of a second. Once deployed, the active roll bars help to maintain an occupant survival area together with the Important note windscreen surround (and the hard top if used). The active roll bars are also deployed in the event of a sufficiently severe rear or side collision as a precautionary measure against subsequent roll-over of the vehicle. Since it is impossible to gauge vehicle dynamics and movements of the occupants in an accident, the active roll bars are also activated as a precautionary measure in the event of: - sufficiently severe head-on collisions (that activate the front airbags) if they have caused a cut-out of the fuel supply - sufficiently severe side-on or rear collisions. · Safety · 3 • 81

Important note Warning The active roll bars are not deployed in the event of a roll-over Never place objects over or near the roll bar covers. around a transverse axis (Y axis in the figure). If the roll bar is activated, they may delay or prevent it coming out. Warning They could also be propelled into the passenger compartment at such high speed as to seriously jeopardise the safety of the Do not travel with rear occupants resting their heads on the roll occupants. bar covers, facing the back of the vehicle or seated on top of the roll bar covers. If activated, the roll bars will increase the risk of injury. Warning If activated, the roll bar must be replaced. Contact the Ferrari Service Network. � � � 3 • 82 · Safety ·

Fuel inertia switch Warning This is a safety switch A in the passenger compartment on the floor The roll bar is a pyrotechnic-powered system. in front of the driver seat that deactivates the petrol pump relays if a collision occurs. System cannot be repaired. A symbol on the TFT display and the hazard warning lights light Risk of injury if accidentally activated up to indicate that the switch has been activated. Each operation must only be performed by authorised staff. When activated, the doors are also unlocked (if locked) and the Contact the Ferrari Service Network. central dome light comes on. Warning Warning Never modify the roll bar modules. Do not damage the roll bar The system can be reactivated by pressing the button on the top module covers (for example pinning something onto them or of the switch. pressing objects against their covers). If, for any reason, a roll bar cover gets damaged, have the roll bar module immediately checked by the Ferrari Service Network. Activation of a damaged roll bar module could cause serious or fatal injuries. Warning � The roll bar modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Booklet” even if the vehicle has NOT been involved in a collision. · Safety · 3 • 83

ABS These adjustment phases will be repeated in cycles in the event that brakes are applied with ABS intervention, until the vehicle comes This is a safety device which activates to prevent wheel locking if to a stop or the pressure on the pedal decreases. the driver depresses the brake pedal too sharply, especially under In addition, the system offers the following advantages: poor grip conditions. - Driving stability (no skidding): even in the event of sharp braking The system is composed of: approaching wheel locking. - electro-hydraulic unit - Manoeuvrability (no side-skidding on sharp turns). - electronic brake-force distribution EBD This means that even when an emergency situation requires sudden - four speed sensors on the wheels, incorporated in the bearings. braking, the driver can avoid obstacles, or brake on a curve, without - the entire ESP sensor system (steering angle sensor, affecting the vehicle stability. accelerometer, yaw sensor, etc.). These features add to the vehicle’s standard braking system, Warning without changing its characteristics. The ABS system features remain unaltered as long as the speed limit for the tyre side grip is not exceeded. When this limit is Important note exceeded, vehicle skidding cannot be avoided. When the ABS system is active, during emergency braking or in poor grip conditions, a “pulsing” sensation will be felt through - Optimal braking distance : the brake pedal. Hold the brake pedal down to continue the depending on the type of road surface, the braking distance may braking action. be reduced by as much as 40%. When one of the wheels starts locking, the hydraulic control unit Warning controls the braking circuit by running a 3-phase cycle: The ABS system does NOT exempt the driver from driving - reduction (if necessary) carefully and responsibly at all times. - maintenance - pressure increase in the hydraulic circuit. 3 • 84 · Safety ·

F1-Trac Important note F1-Trac is directly derived from Ferrari's expertise in F1 vehicles. The ABS system cannot compensate for driving at excessive This system optimises traction by controlling engine power delivery. speeds with respect to the traffic or road conditions, worn tyres, F1-Trac is faster and more accurate than the traditional control worn braking system components or driver errors. systems, and is capable of delaying and minimising engine torque adjustments as required, in order to ensure the desired trajectory. The ABS system has been designed for the sole purpose of assisting The system estimates the maximum available grip in advance, by the driver in controlling braking under extreme conditions, in continuously monitoring the relative wheel speed and using an which he/she could instinctively cause the wheels to lock. auto-adaptive operation logic. Comparing this information with CST - Stability and Traction Control the vehicle dynamics model stored in the control system, F1-Trac optimises the vehicle behaviour by controlling engine torque The CST is composed of two main systems: delivery. VDC Vehicle Dynamics Control, performed through the braking system and engine torque Important note F1-Trac traction control, performed through engine torque modulation, depending on maximum grip on the road F1-Trac does not work when the Manettino is set to CST off. and of secondary systems that are always active, such as the ABS, EBD, etc. To provide optimal control in different driving and grip conditions, four different setting levels have been designed: - Level 1: ensures stability and maximises traction on every type of road surface, both in low (Manettino set to Comfort) and very low grip conditions, by means of engine and brake control (in this condition, the standard ASR system activates instead of the F1-Trac function). - Level 2: ensures stability and maximises traction only in medium- to high-grip conditions (Manettino set to SPORT) optimising engine and brake control. - Level 3: CST off (position ). Stability is not ensured, but all the other features always present in the other settings, such as the ABS and EBD, remain active. When the brake pedal is depressed, the VDC system reactivates. · Safety · 3 • 85

EPB - Electronic parking brake Its characteristics are: • Gradual release of brake shoes/pads when vehicle starts up (AVH The parking brake is controlled by a small electric engine. function): this guarantees an optimised release It can be applied and released using the special control A on the • Automatic activation when engine is switched off (AUTOHOLD dashboard to the left of the steering wheel. function) with possibility of disabling automatic activation using The brake is automatically activated when the engine is switched off the AUTOPARK B button which is part of the EPB control. and can be temporarily deactivated by pressing the AUTOPARK B button. Warning Pushing down the brake pedal and pressing button A deactivates it automatically. Always apply the parking brake when the vehicle is parked. The electric parking brake can operate as an emergency brake when The vehicle should be blocked. If this is not the case, please the vehicle is in motion. contact the Ferrari Service Network. If this is the case, the electric parking brake communicates with the ESP system to prevent locking. The warning light will turn off when the parking brake is fully released. TFT display warning light display priority levels Priority level 0 (Extremely critical malfunction): is displayed for 20 seconds. Priority level 1/Priority level 2 (Critical malfunction/Non-critical malfunction): is displayed for 20 seconds in the centre of the TFT display. After 20 seconds, the symbol remains displayed in minimised form if there is no specific warning light. � � 3 • 86 · Safety ·

Tyre pressure and temperature Warning monitoring system The system warns the driver that there is a drop in tyre pressure. The vehicle is equipped with a system that measures tyre pressure However, this does not exempt the driver from periodically and temperature using special sensors fixed inside the wheel rims checking that the tyres are inflated to the indicated pressure. next to the air valve. These sensors send a signal that is received by the antennas fixed to the body behind the gravel guards that are In addition, the system does NOT warn the driver of damage to connected to the ECU. the tyres by external agents. Important note Displaying messages on the “TFT” display The system may be momentarily affected by radioelectrical By pressing a special DISP button, the driver can access the interference from devices that use similar wavelengths. TYRES screen page that shows the pressure and temperature values of each tyre as in the following example 1. The ECU processes this information and transmits data on tyre The TYRES screen page can be set as the standard screen page pressure and temperature and any system errors to the instrument (see page 127). panel via a CAN line. The signal transmitted by the ECU activates symbols on the TFT display with two priority levels: a soft warning (sw) if the pressure loss compared with the nominal pressure exceeds 0.2 bar and a hard warning (hw) if it exceeds 0.5 bar or there is a dynamic loss of over 0.2 bar/min. The system can be calibrated using the special menu item in the TFT display (see page 123). Important note System calibration using the special menu item on the TFT display is necessary after replacement or inflation of a tyre or tyres. · Safety · 3 • 87

If an event occurs that needs to be viewed when the TYRES screen Low pressure page is being displayed, the screen is displayed in reduced form as When the on-board instrument panel receives the signal from the in the following example 1: tyre pressure ECU that the pressure level of one or more tyres is Once it has been displayed, the TYRES screen page is displayed below the alarm threshold, the following screen will appear (with again. If malfunctions/events occur for which a summary symbol any type of screen displayed): needs to be displayed, the symbol will be displayed in one of the - for a warning for only one tyre (example 3) two specific areas (example 2) until the malfunction is corrected. - for a warning for several tyres (example 4). Once the display time has elapsed, the screen page disappears. The next time the engine is started, if the failure persists, the screen page shown above will be displayed (example 3 or 4). The TYRES screen page can be displayed by pressing the special DISP button. In this way, you can locate the tyres with insufficient pressure compared with normal operating conditions at any time (example 5). Occasionally, the system may be unaware of which wheel signals a failure and cannot therefore specify the right wheel. Check tyre Check tyre Powersteering pressure pressure Malfunction 1 � 3 4 3 • 88 · Safety ·

If this occurs, the following screen page will be displayed Tyre puncture (example 6). When the on-board instrument panel receives the signal from the Once the display time has elapsed, the screen page disappears. tyre pressure ECU that the pressure level of one or more tyres is below the alarm threshold, the following screen will appear (with The TYRES screen page showing the pressure of each tyre cannot any type of screen displayed): be recalled by the driver. - for vehicles with normal tyres (example 7) Obviously, the next time the engine is started, if the pressure fault persists, the screen page will be displayed again and once the - for vehicles with RUN FLAT tyres (example 8) display time has elapsed, the screen page disappears. At the same time, the relative warning light on the instrument panel turns on (see page 142). If normal tyres are used, the failure follows the same display logic as the other failures with priority 0 until the situation is corrected and the system requires subsequent calibration. When the display cycle ends, the screen page disappears whereas the warning light remains on in fixed mode. Check tyre pressure Low tyre Low tyre pressure pressure Do not Max speed proceed 80 km/h � 6 7 8 · Safety · 3 • 89

When the TYRES screen page is displayed, you can identify the If another tyre is punctured, the instrument panel will calculate the punctured tyre under normal operating conditions (example 9). updated number of km (mi) which can still be driven based on the distance driven after the previous puncture The instrument panel will calculate the residual tyre life and repeat (example 12). the display after 50 km (31 mi). During the “punctured tyre” condition, after driving more than If the driver presses the MODE button while the priority 0 100 km (62 mi), the screen page (example 10) will be displayed (normal tyre puncture) or priority 2 (Run Flat tyre puncture not or if the vehicle speed exceeds 80 km/h (50 mph), the screen page in a speed limit exceed condition with the tyres still in a driving (example 11) will be displayed according to the logic for priority condition) faults are being displayed, the screen page will disappear level 0 faults. but the warning light will remain on in fixed mode. Low tyre Low tyre Low tyre pressure pressure pressure Do not Max speed Max speed proceed 80 km/h 80 km/h � 10 11 12 3 • 90 · Safety ·

Here too, the TYRES screen page can be displayed by pressing - for vehicles with RUN FLAT tyres (example 15). If the fault the special DISP button. In this way, you can locate the punctured occurs when the TYRES screen page is displayed, the displayed tyres compared with normal operating conditions at any time screen page will automatically become the default one. (example 13). When the display cycle ends, the screen page disappears whereas Occasionally, the system may be unaware of which wheel signals a the warning light remains on in fixed mode. failure and cannot therefore specify the right wheel. In this case, the The instrument panel will calculate the residual tyre life and following screen page will be displayed: repeat the display after 50 km (31 mi). - for vehicles with normal tyres (example 14). If the fault occurs when the TYRES screen page is displayed, the displayed screen page will automatically become the default one. Low tyre Low tyre pressure pressure Do not Max speed proceed 80 km/h ���� 14 15 · Safety · 3 • 91

During the “punctured tyre” condition, after driving more than System not calibrated 100 km (62 mi), the screen page (example 16) will be displayed or if the vehicle speed exceeds 80 km/h (50 mph), the screen page Warning (example 17) will be displayed according to the logic for priority level 0 faults. Before calibrating the system, make sure that the tyre pressure corresponds to the indicated pressure values (see page 28). If The TYRES screen page showing the pressure of each tyre cannot this is not the case, the system may issue wrong low pressure be recalled by the driver. indications. If the system has not been calibrated or after replacement of one or more tyres, the screen page (example 18) will be displayed. At the same time, the warning light on the instrument panel (see page 142) will flash for 90 sec. When the display cycle ends, the screen page disappears. The warning light remains on until the system has been calibrated. The system can be calibrated using the special menu item in the TFT display (see page 123) (ignition key in position II and engine off). Low tyre Low tyre TPMS pressure pressure not calibrated Do not Max speed Execute proceed 80 km/h calibration 16 17 18 3 • 92 · Safety ·

When the Menu item is displayed and the subsequent calibration Tyre pressure monitoring system failure accepted, the following screen page (example 19) appears for 5 sec. The following screen page (example 21) is displayed in the If the TYRES screen page is displayed, the displayed screen page following cases: will automatically become the default one (example 20). - fault on the circuit and/or wiring to the ECU For “Calibration Activated” the TYRES screen page can be called - signal is not received by one or more sensors due to a faulty, up but the pressure and temperature values are replaced by dashes. broken or flat battery - fault in the TPMS ECU. At the same time, the warning light on the instrument panel (see page 142) will flash for 90 sec. The warning light then remains on in flashing mode until the situation is corrected. If the TYRES screen page is displayed, the displayed screen page will automatically become the default one (example 21). The TYRES screen page cannot be recalled by the driver. Calibration TPMS activated not calibrated TPMS failure Execute calibration 19 20 21 · Safety · 3 • 93

System temporarily inactive System inactive When the following conditions occur: For a few seconds at key-on, if the system has been deactivated by a - temperature too high diagnosis tool, the following screen page appears (example 23). - during calibration (the TPMS ECU does not recognise the At the same time, the warning light on the instrument panel (see sensors) page 142) will flash for 90 sec. The warning light then remains on - radio frequency that interferes with the wheel sensor signal in flashing mode until the situation is corrected. the following screen page appears (example 22). If the TYRES screen page is displayed, the displayed screen page will automatically become the default one. At the same time, the warning light on the instrument panel (see page 142) will flash for 90 sec. The warning light then remains on Subsequently (or after pressing the special DISP button), the in flashing mode until the situation is corrected. screen page disappears whereas the warning light remains on. Subsequently (or after pressing the special DISP button), the The TYRES screen page cannot be recalled by the driver. screen page disappears whereas the warning light remains on. The TYRES screen page cannot be recalled by the driver. �� TPMS TPMS inactive temporarily �� inactive 22 23 3 • 94 · Safety ·

Summary of TPMS displays TYRES screen page Message Vehicle Symbol Recovery (no can be displayed on request Function + Symbol (Area B2) (Area B1) connection) Recovery (no In normal conditions connection) Vehicle symbol in the centre of the Vehicle with tyre pressure TFT display with and temperature values. Generic failure tyre pressure and Low tyre The background of symbol temperature values. Check tyre pressure pressure the box indicating the + The background of the pressure value for the specific symbol box with the pressure faulty tyre is amber. + value for the faulty tyre is amber. “Electrical system failure” message for Not 20 sec. recallable Low tyre pressure (when the Check tyre pressure After 20 sec. or when - the MODE button is Not recallable system does (message only) not recognise pressed, the generic the tyre) failure symbol is minimised TPMS not calibrated TPMS Execute calibration - Not recallable not calibrated + Tyre (amber) · Safety · 3 • 95

Summary of TPMS displays TYRES screen page Message Vehicle Symbol Recovery (no can be displayed on request Function + Symbol (Area B2) (Area B1) connection) Recovery (no In normal conditions connection) Vehicle symbol in the Calibration activated centre of the display Calibration + - with tyre pressure and in progress Tyre (green) Generic failure temperature values symbol replaced by dashes. TPMS failure + TPMS failure + - specific symbol Not recallable Tyre (amber) + “Electrical system Vehicle symbol in the Low tyre pressure failure” message for Not centre of the display Do not proceed 20 sec. recallable Vehicle with yellow with tyre pressure and Tyre puncture + punctured tyre temperature values and After 20 sec. or when punctured tyre shown Tyre (amber) the MODE button is in yellow Tyre puncture pressed, the generic Low tyre pressure failure symbol is (when the system does Do not proceed minimised - Not recallable not recognise + the punctured Tyre (amber) tyre) 3 • 96 · Safety ·

Summary of TPMS displays TYRES screen page Message Vehicle Symbol Recovery (no can be displayed on request Function + Symbol (Area B2) (Area B1) connection) Recovery (no In normal conditions connection) Low tyre pressure Run Flat puncture Do not proceed Vehicle with yellow after 100 km + punctured tyre Generic failure (62 mi) Vehicle symbol in the Tyre (amber) symbol centre of the display + with tyre pressure and Run Flat Low tyre pressure specific symbol temperature values and puncture punctured tyre shown Max speed 80km/h Vehicle with yellow + (or if a speed in yellow + punctured tyre “Electrical system of 80 km/h is Not Tyre (amber) failure” message for exceeded) recallable 20 sec. TPMS temporarily TPMS inactive After 20 sec. or when temporarily - the MODE button is Not recallable + inactive pressed, the generic Tyre (amber) failure symbol is TPMS inactive minimised TPMS inactive + - Not recallable Tyre (amber) · Safety · 3 • 97

TAB 1. child restraint systems that can be installed with 3-point seat belts - 2-seater version SEAT GROUP WEIGHT RANGE Front passenger 0 0 - 10 kg X 1 9 - 18 kg UF - L 2 15 - 25 kg UF - L 3 22 - 36 kg UF - L TAB 2. Child restraint systems that can be installed with 3-point seat belts - 2 + 2-seater version SEAT GROUP WEIGHT RANGE Driver-side side rear Opposite driver-side side rear 0 0 - 10 kg X U-L 1 9 - 18 kg U-L U-L 2 15 - 25 kg U-L U-L 3 22 - 36 kg U-L U-L 3 • 98 · Safety ·

TAB 3. Child restraint systems that can be installed with ISOFIX - 2 + 2-seater version SEAT GROUP WEIGHT RANGE Driver-side side rear Opposite driver-side side rear 0 0 - 10 kg X L 1 9 - 18 kg L L 2 15 - 25 kg X X 3 22 - 36 kg X X TAB 4. Special Ferrari Baby Smart™ child restraint systems (Produced by Britax-Römer)- 2 + 2-seater version GROUP WEIGHT RANGE Name 0 0 - 10 kg BABYSAFE Plus 1 9 - 18 kg DUO Plus 2 15 - 25 kg KID Plus 3 22 - 36 kg KID Plus Key U = suitable for “Universal” category restraint systems homologated for use in this weight group. UF = suitable for forward-facing “Universal” category restraint systems homologated for use in this weight group. L = suitable for the special restraint systems listed in TAB 4. These restraint systems can be “vehicle specific”, “limited” or “semi-universal”. B = built-in restraint system homologated for this weight group. X = seat not suitable for children in this weight group. · Safety · 3 • 99

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Doors When pulling handle B to open the door, the window will move down to its “target position”. Opening from the outside When the door is closed, it will move back up until it meets the Using the remote control, deactivate the alarm and the central door “upper weather strip”. locking system, or turn the key in the lock to deactivate the central If the handle B is pulled without opening the door, the window will door locking system. lower to the “target position” but, after 2 seconds, if the door is not When pulling the handle A to open the door, the window moves opened, the window moves up to the “upper weather strip”. down approximately 2 centimetres. When the door is closed, it will Therefore, to open the door, release the handle B and pull it again. move back up until it meets the upper limit. Press the “LOCK” C button on the roof to lock both doors and press the “UNLOCK” C button again to unlock them. Locking and opening the doors from the inside Warning Always check that the door is closed properly to prevent it from opening while driving. � � � 4 • 102 · About your vehicle ·

Engine compartment lid Emergency Opening Opening If the lid opening lever does not work, there is a string for manual emergency opening underneath the dashboard near the foot rest To unlock the engine compartment lid, pull the lever D underneath area on the passenger side as shown by the arrow in the figure. the steering column. Release the lever E retaining the lid. This lever is located in the front section of the vehicle in a central position. The lid is held open by two shock absorbers F. Closing Lower the lid until it is closed and press down near the lock until you hear it click in place. Warning Always check that the lid is closed properly to prevent it from opening while driving. � � � · About your vehicle · 4 • 103

Luggage compartment lid Fuel tank cap and flap Opening To open the luggage compartment lid, press button H or button L Warning on the remote control and hold it for more than 2 seconds. You can Always turn off the engine during refuelling. Take extreme care also use the special knob to the right of the number plate lights. when removing the cap. The luggage compartment is illuminated by an internal light that Do not smoke or use open flames when refuelling. comes on automatically when the luggage compartment lid is opened. The following can be harmful for your health: Closing - fuel coming into contact with your skin Using the grip on the inside, lower the luggage compartment lid - inhaling fuel vapours. until it touches the bodywork. The lock will pull the lid down until it clicks in place. Opening To open the fuel tank cap flap, press button M to the left of the Warning driver-side floor. Unscrew the cap P, rotating it counterclockwise and hang it on the Since the lock closes automatically, always keep your hands hook Q. away from the area between the luggage compartment lid and the bumper. L H M 4 • 104 · About your vehicle ·

Closing Emergency Opening Screw the cap P back on tightly and close the fuel filler flap. In the event of a failure of the fuel tank cap flap button, the flap can be opened manually. Make sure that the string R is not hanging out of the fuel filler flap. Open the luggage compartment lid, turn the lock E and open the flap F. Pull the emergency string G. P R F E Q P � · About your vehicle · 4 • 105

Power windows Passenger-side power window The power windows can only be used with the ignition key in Press button B to move the window up or down. position II. Only manual operation is possible (partial opening) to raise the Driver-side power window window: when button B is released, the window stops at the position reached. Press button A to move the window up or down. This button allows manual operation (partial opening/closing) or automatic To lower the window, automatic operation is also possible (full operation (complete opening/closing). Press button A briefly to opening): if the button is pressed at length (over 0.3 seconds) the activate manual operation; if the button is pressed at length (over automatic window operation is activated. The window will only 0.3 seconds) the automatic window operation is activated. The stop when it reaches the end of its travel or by pressing the button window will only stop when it reaches the end of its travel or by again. pressing the button again. When the door is open, the window can only rise to the “target position”, to prevent the window from colliding with the upper weather strip when it is closed. � � 4 • 106 · About your vehicle ·

“Global Open” function Quickly press the “Retractable hard top” button twice to open all Warning four windows at the same time. Improper use of the power windows can be dangerous. Before “Global Closed” function use, always check that people and objects are at a safe distance. Quickly press the “Retractable hard top” button and then hold it Pay particular attention during the automatic operation of the down to close all four windows at the same time. driver-side power window. Rear power windows To protect the passengers remaining in the car against accidental With the driver side front window lowered, press button A again to operation of the power windows, always remove the key from lower the driver side rear window. the ignition. With the passenger side front window lowered, press button B again to lower the passenger side rear window. To raise the rear windows, simply lift button A for the left window and B for the right window. · About your vehicle · 4 • 107

Instruments and gauges � � � � � � � � � � 4 • 108 · About your vehicle ·

1 TFT Display Rev Counter 2 Electronic speedometer The rev counter indicates the engine RPM. 3 Rev Counter The numbers on the dial multiplied by 1000 correspond to the 4 Gear display engine RPM in one minute. 5 Warning lights There is a space to the bottom right of the rev counter for the “DOT MATRIX” display which gives information on the “Semi- 6 Manettino status automatic gearbox”. 7 Fuel level Electronic speedometer The speedometer indicates the effective speed of the vehicle. · About your vehicle · 4 • 109

Retractable hard top Warning The hard top system is composed of three main moving parts: - top part Before operating the retractable hard top, make sure that the backrest of the child restraint system is set to its minimum height. - rear part with rear screen - luggage compartment lid. The preliminary steps for opening and closing the retractable hard Opening and closing is actuated by a hydraulic system, driven by top are: a pump and controlled by a number of sensors that check every - vehicle must be stationary phase of opening and closing. - luggage compartment must be closed - battery voltage must not be below 11 volts Warning - partition between luggage compartment and folded roof For safety reasons, the retractable hard top can only be opened compartment must be in the correct position, fully pushed back and closed when the vehicle is stationary. and fastened Warning Warning Do not place items above the partition! Risk of serious damage The roof must be opened or closed whilst remaining correctly to opening and closing mechanisms. seated in the driver's seat. Warning Before activating the roof and while it is in motion, always check that people and objects are at a safe distance from the moving parts of the roof. In the event of danger, release the roof switch; all movement will stop immediately. Important note Before opening or closing the hard top, refer to “Placing suitcases in the luggage compartment” on page 177. 4 • 110 · About your vehicle ·

- check there is adequate space heightwise and in the rear of the vehicle: Roof opening using switch the minimum available height A must be 1700 mm, the minimum distance B of an obstacle from the rear must be more than 400 mm. Important note - ignition key in position II and engine running Before opening the roof, ensure that the top of the roof and the rear screen are dry to avoid water entering the passenger Important note compartment or luggage compartment. We recommend operating the retractable hard top with the engine running. Pull back switch A on the centre console and hold until the roof is completely open. Important note The operation in progress will be indicated by a warning on the TFT display. If distance B is less than 400 mm, the parking sensors will not When the button is pressed, a series of operations required to open allow the roof to open or close. or close the retractable hard top begins: The parking sensors are only activated when the key is in - the side windows are lowered completely position II. - the rear screen is raised - no overheating of hydraulic system. - the luggage compartment lid rotates around a hinge fitted in its If one or more conditions are not met, the following message will rear appear on the TFT display. � � � � · About your vehicle · 4 • 111

Roof opening Roof open - the rear screen and luggage compartment lid parts are positioned Roof closing using switch in the luggage compartment Push forward switch A on the centre console and hold until the - the luggage compartment lid is closed. roof is completely closed. The operation in progress will be indicated by a warning on the Important note TFT display. Throughout all these phases, the side windows cannot be When the button is pressed, a series of operations required to open activated. or close the retractable hard top begins: - the side windows are lowered completely At the end of the opening cycle, an acoustic signal will indicate the - the luggage compartment lid lifts and rotates backwards end of operations and the phase will be indicated with a message - the top part of the roof comes out of the luggage compartment on the TFT display. and rests on the edge of the windscreen surround - the luggage compartment lid completes the closing phase Warning - the rear screen starts moving back and goes into position. Do not reverse the opening or closing direction when opening Once the operation has been completed, an acoustic signal indicates or closing the roof. that the switch can be released. Always complete the cycle until the acoustic signal is emitted. 4 • 112 · About your vehicle ·

Roof closed �������� ���������� Standby operations Disallowed operations If the button is released before the retractable hard top has been If the conditions for opening or closing the retractable hard top are completely opened or closed, a message will appear on the TFT not met, this will be indicated by an acoustic signal and a message display and will remain until opening or closing is reactivated. on the TFT display: Warning - roof is activated when the vehicle is moving Do not drive until opening or closing has been fully completed. A few minutes after the roof is in standby position, an acoustic signal and message on the TFT display will prompt you to complete the operation. Roof operation inhibited Warning Stop car for roof operation Avoid leaving the hard top in a standby position. · About your vehicle · 4 • 113

- the speed signal transmitted via the CAN network is not detected - battery voltage is below 11 volts by the ECU - the luggage compartment has not been closed correctly Roof operation inhibited Low battery for roof operation - partition between luggage compartment and folded roof compartment must be in the correct position, fully pushed back and fastened Roof operation Roof operation inhibited inhibited Close trunk for Close luggage roof operation separator 4 • 114 · About your vehicle ·

- there is overheating of the hydraulic system - the parking sensors have detected an object in the rear of the - the window position sensor detects that at least one of the vehicle windows is not in the correct position Roof operation inhibited System overheating Roof operation Roof operation inhibited inhibited Windows Obstacle failure detected · About your vehicle · 4 • 115

- the parking sensors are not communicating with the ECU. Warning of faulty opening and closing If there is a problem with opening and closing the roof, the fault Warning will be indicated by an acoustic signal and a message on the TFT display. DO NOT open the retractable hard top when the outside After 20 seconds or after pressing the MENU button, the screen temperature is below -10 °C (14 °F). page is minimised to an icon and moves to the bottom left of the TFT display. Warning If there is a fault in the retractable hard top system, contact the Ferrari Service Network. Max speed Parking sensor Roof failure Avg. speed failure Distance Warning! Trip time Possible obstacles Range 4 • 116 · About your vehicle ·

Lighting High beams The external lights and the direction indicators only work when the To turn on the high beams when the light switch A is set to , ignition key is in position II. push the left-hand lever B towards the dashboard. The external lights can be switched on and off manually or When the high beams are on, the relative warning light illuminates automatically, depending on daylight conditions. on the instrument panel . Pull the lever B towards the steering wheel again to turn off the Light switch high beams and turn on the low beams. Switch A has five positions: Flashing the headlights 0 Lights off The headlights can be flashed by pulling the left-hand lever B Running and number plate lights on (*) towards the steering wheel. Low beams on (*) Flashing occurs also with lights off if the ignition key is set to II. Parking lights High beams are used for flashing. AUT Automatic operation of the external lights according to the ambient light. Important note (*) The relative warning light on the instrument panel comes on. Follow the Road Regulations of the country you are travelling in for using the high beams. � � · About your vehicle · 4 • 117

Parking lights Parking lights work only with the ignition key in position 0 or with Warning the key removed. If there is fog during the day, the running lights and low beams They are activated by turning the light switch A to position . will not be turned on automatically. The driver must always be When the parking lights are on, the warning light illuminates on the ready to turn on the lights manually and also the rear fog lights, instrument panel . if necessary. When the parking lights are on, move the left-hand lever B downward to turn on the left-side running lights. Move the lever Important note upward to turn on the right-side running lights. After automatic activation of the external lights, it will always When the partial parking lights are on (lights only on one side of be possible to turn on the rear fog lights manually. When the vehicle), the running light warning light turns off whereas a the external lights are deactivated automatically, the rear fog special message is displayed on the TFT display for 10 seconds. lights are also turned off (if active) automatically. Therefore, When the light switch A is turned to AUT and the ignition key is in if necessary, the driver will have to turn on the rear fog lights position II, the running lights, low beams and number plate lights manually upon the next automatic activation. turn on and off according to the ambient light. Important note Warning The high beams can only be activated manually, by pushing the The driver is always responsible for turning on the external left-hand lever B towards the dashboard. lights, depending on the ambient light and in compliance with the regulations in force in the country of use. The automatic system for turning on and off the external lights must be Important note considered an aid for the driver. If necessary, turn the lights on and off manually. If the high beam control is activated, the high beams will turn on every time the lights are activated automatically. We recommend therefore that you turn them off every time the twilight sensor deactivates the external lights. 4 • 118 · About your vehicle ·

Twilight sensor Direction indicators The twilight sensor is comprised of a global sensor, which measures When lever B is: the ambient light upwards. - moved up, the right-hand direction indicators are turned on; In the event of sensor failure, the system switches on low beams - moved down, the left-hand direction indicators are turned on. and running lights irrespective of daylight conditions; a failure message will appear on the instrument panel display. The relative warning lights or will illuminate on the The failure indication will be displayed as long as the light switch A instrument panel. is turned to AUT. The lever returns to the neutral position automatically when the In this case, we recommend that you deactivate the automatic steering wheel is straightened. system and turn on the external lights manually if necessary. To indicate a temporary lane change, requiring only the slightest turn of the steering wheel, the lever can be moved without clicking Important note it into position (non-permanent position). Contact the Ferrari Service Network as soon as possible. � · About your vehicle · 4 • 119

Rear fog lights Hazard warning lights These can be activated only when the high or low beams are on, by Press button A to turn on the hazard warning lights. All the pressing button D. The relative warning light E on the instrument direction indicators will start blinking intermittently. These lights panel will turn on. will operate with the ignition key in any position. When the lights are on, the relative warning lights on the Important note instrument panel and the button flash. To turn them off, press the button again. Use the rear fog lights only in poor visibility conditions. � � � 4 • 120 · About your vehicle ·

Adaptive light system (optional) Dome light The “Adaptive Light” system not only illuminates the road better When the doors are closed, the dome light D on the roof can be but also avoids the shadowy areas in the curved trajectory of the turned on or off using the switch E. vehicle. Switch F is used to turn on the driver side spotlight and switch G The beam angle is defined by the following parameters: turns on the passenger side spotlight. - steering angle The dome light activates automatically in the following conditions: - vehicle speed - when a door is opened, for approx. 3 minutes - lateral acceleration. - when all the doors are closed and the key is in position 0, for approx. To avoid shadowy areas when driving on bends, the lighting 10 seconds direction of the beams varies from 7.5° inwards and 15° outwards. - when the key is removed, for approx. 10 seconds - when the doors are unlocked, for approx. 10 seconds - when the inertia switch is activated, for approx. 15 minutes. The dome light deactivates automatically in the following conditions: - after the preset activation time expires - when the doors are closed and the key is in position II - when the doors are locked - when the inertia switch is reactivated. � � � � · About your vehicle · 4 • 121

“TFT” display Six different screen areas are available, depending on the display type chosen: Located on the instrument panel, it performs the following functions: A - display of clock, selected driving mode indication (“Manettino” position), outside temperature and “Warning: danger of ice” - indication of the control parameters icon - indication of general information while driving B - display of virtual control gauges and information generated by - fault warnings. specific events and/or on request, engine coolant temperature/ The driver can interact with the system by choosing graphic engine oil temperature gauges, parking sensor screen page, configurations and setting the parameters. display of abnormal events / warnings with messages and special symbol when available The screen is activated and set by pressing the buttons DISP (H), MODE (L) and UP, DOWN (I) on the dashboard to the left of the C - display of 0/1/2 priority level faults (see page 139), engine steering wheel. coolant temperature/engine oil temperature gauges D - audio info / check - check OK indication / “Calling” info E - fuel level gauge, total or trip odometer (TRIP A or B) / range F - speedometer repeater. � � � 4 • 122 · About your vehicle ·

Parameters shared by all the configurations Configuration settings Clock Menu Page The clock is always displayed to the right in area A in all To display the MENU page, press the DISPLAY button. configurations and can be viewed in the “24h” or “12h – AM/PM” The parameters that may be set are: format. - Dimming Date and hour - Display setup The data in the Trip A/ Trip B screens is displayed in the day of - Date and hour week (e.g. Mon.) mm format. It can be set using the UP and DOWN buttons through Menu function. To confirm, press MODE. - Language and M. U. The time may be displayed in the “24h” or “12h – AM/PM” format. - Car setup To select the format and set it, use the UP and DOWN buttons - Calibrate TPMS through Menu function. To confirm, press MODE. - Service. Outside temperature gauge To select the above mentioned parameters and the related The information is displayed to the left in area A. functions, use the UP and DOWN buttons. To confirm the selected parameter, press MODE. Display setup Display setup Date/Hour Date/Hour Language/M.U. Language/M.U. Car setup Car setup Dimming Dimming · About your vehicle · 4 • 123

KEY ON If only conditions 1, 3, 4 are met (no engine start), the previously Upon key-on, the check procedure is started and, regardless of the saved main screen will appear directly (also after a key-off/key-on). main screen page, the message “Check” is immediately displayed The “Check OK” message is displayed as soon as condition 2 is met in area D on a grey background divided into 5 “segments” that are provided the others are maintained. gradually highlighted as the 5 seconds elapse. 1 the initial check time of the warning lights on the dial has elapsed 2 the engine RPM has exceeded the set value, from the moment that this threshold is exceeded 3 the check procedure has been successfully completed (no failures) 4 the Service information has been displayed for 5 seconds (when provided) Subsequently, the “Check OK” message will appear. 4 • 124 · About your vehicle ·

DISP (DISPLAY) button When pressed for more than 2 seconds: Press the DISP button to display the following screen pages: - if the MENU screen is displayed: it takes you back to the previous - SPORT level in the MENU (when in the submenu functions) - TYRES - if the MENU page is not displayed: - TRIP A/B - if total odometer, travel distance TRIP A or Range information is displayed, Odo A information flashes in the same area - MENU - if travel distance TRIP B is displayed, Odo B information flashes in the same area MODE button - if the MENU page is not displayed and TRIP B is disabled: it resets When pressed for less than 2 seconds: Trip A. - if the MENU screen is not displayed: it switches between total odometer information, “travel distance” TRIP A, “travel distance” UP / DOWN button TRIP B (if enabled) and range The UP/DOWN button is a single button divided into two parts, - if the MENU screen is not displayed and the odometer flashes: it the top part corresponds to the UP control and the bottom part resets the Trip information for the flashing odometer (TRIP A/B) corresponds to the DOWN control: - if the MENU screen is displayed: - sets/adjusts the functions on the MENU page - it confirms the selected function - MENU page not active: adjusts the instrument panel brightness - if confirms the setting/change and returns to the previous screen level (same item) when in the submenu functions in the main MENU - Auto function (twilight sensor active): adjusts the sensor's sensing - it stores the confirmed changes range. - it exits the display of the various check phases at key-on - the malfunctions are iconised if the button is pressed during fault warning display cycles. · About your vehicle · 4 • 125

SPORT When the SPORT screen page is displayed and an event occurs In addition to the shared parameters, the screen page shows the that needs to be viewed, the display will appear as in the following virtual control gauges, for: example: - water temperature - oil temperature. Fuel level low Range 156 km In case of malfunctions/events which need to be displayed through a multifunction symbol, this will be viewed at the end of the display cycle, in one of the three dedicated sections of area C. 4 • 126 · About your vehicle ·

TRIP A/B TYRES (tyre temperature and pressure display) The screen page displays information on the following parameters: The Tyres screen page includes a vehicle symbol which indicates - maximum speed the pressure and temperature levels for each tyre. - average speed If an event occurs that needs to be viewed when the TYRES screen page is being displayed, the screen is minimised. - travel distance - travel time - range - date. When displaying the parameters, the zeros to the left of the most significant figure are deleted. If an event occurs that needs to be viewed when the Trip A/B screen page is being displayed, the Trip information is minimised: TRIP A Maximum speed Average speed Fuel level low Travel distance Travel time Limited Range cruising range · About your vehicle · 4 • 127

MENU If an event occurs that needs to be viewed when the Menu screen The Menu screen is accessed using the “Display” button. The Menu page is being displayed, the display depends on the selected menu screen can be displayed at several levels; here is an example of a level: display for a selection at levels: First level The event will be displayed in the dedicated area (area B) whereas the Menu with the main items only will be moved to the right of the display. From the second level onwards, the new event will be displayed over the Menu screen. In any case, when a new event is being displayed, the menu Display setup functions cannot be accessed and they will be displayed with a Date/Hour “softer” background. Language/M.U. At the end of the new event display cycle, the menu level that was Car setup active before the new event was displayed will be restored. Dimming M.U. distance M.U. temp. Language M.U. pressure 4 • 128 · About your vehicle ·

Fuel level gauge If the vehicle is already in a limited range condition, the range This information is always present on the display (Area E). signal will be replaced by a “Limited cruising range” message and the screen page will appear as in the example: The gauge has 9 yellow bars that gradually “go out” as the fuel level drops. When the second notch goes out, the last notch turns red; this notch will remain lit until the fuel runs out. When the “fuel reserve” condition is reached, a message with symbol is displayed for 10 seconds followed by an acoustic signal in the dedicated area in addition to the warning light lighting up on the panel. Fuel level low Fuel level low Range Limited 156 km cruising range · About your vehicle · 4 • 129

“Warning: danger of ice” display “Adaptive Light Control” function display To warn the driver of the presence of ice on the road if the outside When a failure in the adaptive light system is detected on a bend, temperature is 3 °C (38 °F), the “snow” symbol and ice hazard the warning light flashes on and off and at the same time, a message must be displayed for 10 seconds in the top right of the message with a special symbol is displayed: display. The message is displayed for a set period of time. When this period After the display cycle ends, the message disappears and the screen expires, the screen page disappears but the warning light continues that was present prior to the event reappears. The “snow” symbol to flash until the situation has been corrected. moves to the right next to the outside temperature gauge until the The next time the engine is started, if the failure persists, the temperature remains below 6 °C (43 °F). warning light will flash on and off and the same screen described above will be displayed. �������� ������������� Adaptive Light Control failure 4 • 130 · About your vehicle ·

“Speed limit” function display “Doors/Engine or luggage compartment lid open” function display Using the menu a speed limit can be set between 30 and 250 km/h When doors and the engine compartment or luggage compartment with steps of 5 km/h which, if exceeded, activates the following lid are open, this is signalled by a screen page in which several procedure that warns the driver. doors/lids which are open at the same time can be indicated by A symbol and “speed limit exceeded” message appear in the top specific icons. right of the display accompanied by an acoustic signal. Once the warning cycle has ended, the message disappears whereas the symbol only disappears when the speed of the vehicle drops 5 km/h below the set limit. Doors open Speed limit exceeded · About your vehicle · 4 • 131

“Tyre pressure and temperature” display “Tyre puncture” display The screen page showing the pressure and temperature values of When the pressure level of one or more tyres is below the alarm each tyre can be accessed using the “Display” button. threshold, irrespective of the current display configuration, the When the on-board instrument panel receives the signal from the warning light comes on permanently and a message and special tyre pressure ECU that the pressure level of one or more tyres is symbol are displayed for vehicles fitted with normal tyres and one below the alarm threshold, a different screen will appear according for those fitted with Run Flat tyres. to whether the value is low on one or more tyres. Refer to “Tyre pressure and temperature monitoring system” on Refer to “Tyre pressure and temperature monitoring system” on page 87. page 87. Check tyre pressure Low tyre pressure Max speed 80 km/h 4 • 132 · About your vehicle ·

“Automatic Vehicle Holding” AVH system display External lights failure display The AVH system is an integration of the EPB electronic parking The following failures can be displayed: brake. It blocks the callipers when the electronic parking brake is 1 Stop lights failure engaged in certain situations enabling faster deactivation of the 2 Number plate lights failure parking brake than the EPB. 3 Rear fog lights failure When the AVH system is activated, the word “HOLD” appears on the DOT MATRIX display. 4 Running lights failure (front and/or rear) 5 Turn indicators failure (front and/or rear). If one of these failures occurs, a specific message that highlights the faulty light is displayed. Lamp Failure · About your vehicle · 4 • 133

Dimming of lights Parking sensors The brightness level of the TFT display can be adjusted using the To help the driver when parking, the vehicle has four sensors in the MENU function. front and rear bumpers (optional). When the MENU screen is not displayed, it can be adjusted by pressing the UP/DOWN buttons. Warning The first time one of the UP/DOWN buttons is pressed, the screen page is displayed. The next time the buttons are pressed, the The system will only operate correctly if the sensors on the brightness can be adjusted. bumpers are free of mud, dirt, snow or ice. The adjustment made can be seen immediately and does not affect the brightness of the warning lights. When approaching obstacles in front of or behind the vehicle, the sensors give the driver information on how far away the obstacle is The information on the presence of the obstacle and how far away it is transmitted to the driver by way of acoustic signals, which become more frequent as the obstacle approaches, and visual signals on the TFT display. By integrating direct visual information with the acoustic and visual information generated by the system, the driver can avoid coming into contact with obstacles when parking. Warning However, the responsibility when parking and in other DIMMING potentially dangerous situations, remains that of the driver. Indeed, the system has only been designed as an aid when parking since it detects obstacles that are outside the driver's range of visibility. The use of sensors is therefore not a substitute for the care and attention of the driver when parking and checking for the presence of persons or objects. 4 • 134 · About your vehicle ·

The parking system sensors in the bumpers are automatically The detection zones indicate which part of the vehicle is activated with the key in position II (Ignition) when the reverse approaching an obstacle (front/rear and left, right or central) and at gear is engaged. what distance away it is (maximum, medium, minimum). The rear sensors are also an aid when opening and closing the retractable hard top and reduce the risk of hitting obstacles placed behind the vehicle. Important note If distance B (see page 111) is less than 400 mm, the parking sensors will not allow the top to be opened or closed the 1st time the switch is pressed. When the vehicle is also equipped with front sensors, only the rear sensors or front sensors can be activated/deactivated using the TFT display menu. When the rear sensors are activated, an acoustic signal warns the driver that the system has been activated. If an obstacle is detected at maximum distance in the central front The system then starts to emit acoustic signals as soon as an part, it will be displayed as shown (green): obstacle is detected which become more frequent as the obstacle approaches. When the obstacles is at a distance of less than 35 cm from the bumper, a continuous sound is emitted and the relevant area becomes red on the TFT display (minimum distance, see page 136). The acoustic signal stops immediately if the distance from the obstacle increases. The tone cycle remains constant if the measured distance from the central sensors remains unchanged. The TFT display indicates the vehicle symbol and the sensor detection zones. · About your vehicle · 4 • 135

If an obstacle is detected at medium distance in the central front part, it will be displayed as shown (yellow): If another failure occurs when the parking symbols are being displayed, the TFT display will also show the message for the ongoing failure and the for the parking sensor symbol will move to the right of the display. If an obstacle is detected at minimum distance in the central front part, it will be displayed as shown (red): If the rear sensors are activated and the front ones are deactivated or not present, the TFT display does not display the symbols for the front part. The TFT display can give several items of information at the same time. If an obstacle is detected at a maximum distance in the front central part and at a minimum distance in the rear right part, it is displayed as follows: 4 • 136 · About your vehicle ·

Cleaning the sensors Important note When cleaning the sensors, be very careful not to scratch or If there is higher priority failure such as a tyre puncture, the damage them; avoid the use of dry, rough or hard cloths. TFT display will indicate this failure and the parking sensor The sensors must be washed with clean water and car shampoo symbols will disappear. added if necessary. In car washes that use steam jet or high pressure water cleaning Once the failure has been displayed, the parking sensor symbols equipment, quickly clean the sensors keeping the nozzle at a will go back to the centre of the display. distance of over 10 cm. For the repainting of bumpers or retouching the paintwork in Simultaneous display of parking sensors and other systems the sensor area, contact the Ferrari Service Network. If paint When other systems start operating when the parking sensors are is applied incorrectly, it may interfere with the operating of the being displayed, the TFT display displays the sensors on the right parking sensors. of the screen and the other active system on the left. If the hard top is operated, the parking sensor display is deactivated Range of sensors so that the sensors can concentrate on detecting obstacles that may The sensors allow the system to control the rear and front of the damage the luggage compartment. vehicle and their position covers the central and side areas of the vehicle. If an obstacle is in the central area, it is detected at distances of approximately 1.40 m depending on the type of obstacle and its size. If an obstacle is in the side area, it is detected at distances of less than 0.8 m. Failure signals Roof opening The system ECU checks all the components each time the reverse gear is engaged. A parking sensor system failure is indicated on the TFT display (see page 143). · About your vehicle · 4 • 137

If there is a failure signal, stop the vehicle and turn the ignition key to position 0 (Stop). Then try and clean the sensors or move then Important note away from any sources of ultrasound emissions (e.g. pneumatic Objects placed close to the rear part of the vehicle are not brakes of lorries or pneumatic drills) and turn the ignition key to always detected by the system and may therefore damage the position II again. In this way, if the cause of malfunctioning has vehicle or be damaged themselves. been removed, the system will start operating correctly again and the failure buzzer will stop. If the failure buzzer continues, contact the Ferrari Service Important note Network to have the system checked. The signals sent by the sensors may also be affected by damage to the sensors caused by dirt, snow or ice on the sensors or Important note by ultrasound systems (e.g.. pneumatic brakes on lorries or Obstacles that may damage the luggage compartment (obstacles pneumatic drills) in the vicinity. at distances of less than B, see page 111) are detected only once by the rear sensors prior to hydraulic operating of the hard top. Any obstacles that appear once operating has started will not be Warning detected. However, the responsibility when parking and operating the retractable hard top and in other potentially dangerous situations, remains that of the driver. Indeed, the system has Important note only been designed as an aid when parking and operating the The sensors are able to detect obstacles with reasonably large, hard top since it detects obstacles that are outside the driver's even surfaces (e.g.: poles with diameters of over 60 mm, walls, range of visibility. barriers, trees). Detection is not optimum with obstacles with The use of sensors is therefore not a substitute for the care and sharp projections or uneven surfaces. attention of the driver when parking and verifying the presence of persons or objects. Important note When parking and operating the retractable hard top, always be very careful to avoid obstacles that may be above or below the sensors. 4 • 138 · About your vehicle ·

TFT display and instrument panel warning lights Inertia switch Priority level 0 (Extremely critical malfunction): is displayed for 20 Indicates activation of the inertia switch following seconds. an accident and the resulting cut-out of the fuel supply (priority level 0). Priority level 1/Priority level 2 (Critical malfunction/ Non-critical malfunction): is displayed for 20 seconds in the centre of area B. The hazard warning lights are also After 20 seconds the symbol remains displayed in minimised form automatically activated. if there is no specific warning light. TFT Warning Description and warnings Alternator failure light Alarm system failure If the recharging system is faulty. Indicates a fault in the alarm system (priority When the battery is insufficiently charged or level 1). overcharged (flashing). The system is not programmed (priority level 2). Low windscreen washer fluid level Failure and system not programmed (priority Indicates a low level of washer fluid in the level 1). windscreen washer tank (priority level 2). Alarm system failure (priority level 2). Oil temperature Break-in attempted (priority level 2). Indicates that the oil temperature is too high (priority level 0). Contact the Ferrari Service Network. Adaptive light system failure Indicates an adaptive light system failure (priority Fuel reserve level 2). Indicates that the fuel level is too low (priority level 2). Engine coolant temperature Indicates that the engine coolant temperature is Battery conditioner connected too high (priority level 0). When the instrument panel is on, it indicates that the battery conditioner is connected (priority Turn off the engine and contact the Ferrari level 0). Service Network. · About your vehicle · 4 • 139

Oil pressure Number plate lights failure Indicates that the oil pressure is too low (priority Indicates a system failure or blowing of the level 0). number plate light bulb (priority level 2). Turn off the engine and contact the Ferrari Rear fog lights Service Network. When the rear fog lights are turned on. Indicates a pressure sensor failure (flashing) Twilight sensor failure (priority level 2). Indicates a twilight sensor failure (priority level 2). On board diagnostic system (EOBD) Hard top failure It indicates a malfunction in the emission control Indicates a failure in the retractable hard top system and in the ignition/injection system. (priority level 0). After turning the ignition key to position II, this The type of failure is specified by a special remains on for a self-check for a few seconds message on the display. following engine starting. High beams Cruise Control on When the high beams are turned on. Indicates that the Cruise Control has been turned When the high beams are used to flash. on. Right direction indicators Running lights When the right direction indicators are activated. When the running lights or low beams are turned Left direction indicators on. When the left direction indicators are activated. Stop lights failure Hazard warning lights Indicates a system failure or blowing of the STOP light bulb (priority level 2). When the hazard warning light is activated. Lights failure Indicates a system failure or blowing of a bulb in the running, direction indicators or rear fog lights (priority level 2). 4 • 140 · About your vehicle ·

Catalytic converter temperature ABS Indicates that the catalytic converter temperature is Indicates an ABS system failure (priority level 1). very high: slow down until the warning light goes off (priority level 1). The standard braking system is still functioning. Indicates that the catalytic converter temperature is Contact the Ferrari Service Network. too high: stop the vehicle (priority level 0). Contact the Ferrari Service Network. ASR + CST on Indicates that the ASR and CST systems are active Indicates a failure of the catalytic converter (priority level 1). temperature sensor (priority level 0). ASR + CST off Checking the engine oil level Indicates that the ASR and CST systems are Indicates a low engine oil level. deactivated (priority level 1). Seat heating ASR/CST failure (flashing warning light) Indicates that the seat heating function is activated Indicates an ASR/CST system failure (priority (front RH/LH) (remains displayed for 5 seconds). level 1). Power steering failure Indicates that the power steering system is Warning inefficient (priority level 2). Stop the vehicle avoiding sharp braking. Stop Contact the Ferrari Service Network. driving and contact the Ferrari Service Network immediately. Warning The vehicle can still be driven at low speed (max. 40 Km/h) to free the road. · About your vehicle · 4 • 141

CCM brake discs worn Passenger-side seat belt not fastened Indicates that the carbon ceramic discs are worn Indicates that the passenger-side seat belt is not (priority level 2). fastened (priority level 0). Contact the Ferrari Service Network to have Speed limit exceeded the brake pads replaced. Indicates that the speed set by the driver has been exceeded (priority level 2), the figure shown ASR/CST system activation (flashing warning light) indicates the set speed. Indicates that the CST system has activated Brake malfunction (priority level 1). Indicates that the brake fluid is low (priority level 0). TPMS System Indicates an EBD system failure (priority level 0). Indicates a puncture in one or more normal tyres Indicates an EPB system failure (priority level 0). (priority level 0). Indicates an overhaul of the Parking Brake system Warning light connected to the tyre pressure (priority level 0). monitoring system (priority level 0/2). Rain sensor failure Indicates a puncture in one or more Run Flat tyres Indicates a rain sensor failure (priority level 2). (priority level 2). Indicates a failure in the TPMS (priority level 2). Suspension control system failure Indicates that the TPMS is not activated (priority Indicates a malfunction in the suspension control level 2). system (priority level 2). Indicates that the TPMS is not calibrated (priority level 2). Contact the Ferrari Service Network. Airbag system failure (flashing warning light) Indicates a system failure (priority level 0). Generic failure Indicates an Air Bag warning light failure (priority Contact the Ferrari Service Network. level 2). Indicates a Manettino failure (priority level 1). Driver-side seat belt not fastened Indicates an electrical system failure (priority Indicates that the driver-side seat belt has not level 2). been fastened (priority level 0) together with an acoustic signal lasting 90 sec. 4 • 142 · About your vehicle ·

TPMS System Ice hazard Indicates that calibration of the TPMS has been Indicates that the outside temperature is 3 °C activated. (38 °F) or lower, highlighting the risk of icy road surfaces. Brake pad wear Drive carefully and slow down as the grip of the Indicates excessive wear of the brake pads tyres is markedly reduced. (priority level 2). Activation of passenger air bag Warning Indicates that the passenger air bag has been In this condition, do not activate the “SPORT” activated. mode. Deactivation of passenger air bag Gearbox failure Indicates that the passenger air bag has been deactivated. Indicates a system failure (priority level 1). Parking sensor failure Contact the Ferrari Service Network. Indicates a parking sensor system failure (for vehicles provided with one) (priority level 2). Telephone Indicates that the “Telephone repetition” function has been activated for incoming, outgoing or active calls. Scheduled Maintenance (Service) Indicates the Scheduled Maintenance expiry date. AVH system Indicates an AVH system failure. · About your vehicle · 4 • 143

Electronic speedometer DOT MATRIX semiautomatic gearbox display It indicates the vehicle speed. The DOT MATRIX display is to the bottom right of the rev counter; with the ignition key in position II, it displays the following At a speed of between 0 and 5 km/h, the indicator may remain in information: an idle state. With higher speeds, it indicates the acquired speed. Gear engaged (DCT gearbox) Rev counter “Auto” gearbox mode (DCT gearbox) The electronic rev counter indicates the engine RPM. Avoid engine “Auto easy exit” gearbox mode (DCT gearbox); speeds in the red sector. Performance AVH system activated. Important note Information on the gearbox is useful in all operating conditions. 4 • 144 · About your vehicle ·

Gear engaged (DCT gearbox) When the DCT gearbox is used in “manual” mode and gears are Indicates the engaged gear selected using the steering column stalks, the number indicating the engaged gear appears in the centre of the DOT MATRIX N Neutral display. R Reverse When the DCT gearbox is used in “automatic” mode, the number 1 1st gear indicating the engaged gear appears on the DOT MATRIX display: 2 2nd gear N (Neutral), R (Reverse). 3 3rd gear At key-off if the panel receives the value N (Neutral), the letter N 4 etc..... is displayed whereas if a gear is engaged, the letter P (Parking) is displayed. Launch Launch mode “Auto” gearbox mode Auto Automatic gearbox mode When the DCT gearbox is used in “automatic” driving mode, the Auto▼ Auto easy exit gearbox mode word “AUTO” number appears on the DOT MATRIX display as well as the engaged gear. “Auto easy exit” gearbox signal At each key-on, the “auto easy exit” signal is displayed. A small arrow pointing downwards appears in fixed mode on the DOT MATRIX display. “Launch” mode When the Launch function is required, by pressing the correct button (see page 166), the word “LAUNCH” appears on the DOT MATRIX display until key-off or until the function is activated. AVH system activated When the AVH system is activated, the word “HOLD” appears on the DOT MATRIX display. · About your vehicle · 4 • 145

Roof panel controls Controls on the steering wheel Deactivating the alarm system motion sensors. Press button H to deactivate the anti-lifting alarm system. Start button Press button H again to activate the anti-lifting alarm system. Press the ENGINE START button A to start the engine. When the engine has started, release the ENGINE START button. When this feature is deactivated, the LED on the button flashes for about 3 seconds and then turns off. Do not hold the ENGINE START button down for a long time. Driving mode control switch “Manettino” The driving mode selected does not exempt the driver from complying with the rules of safe driving. The driver can select the driving mode using the “Manettino” B, according to the desired driving style. � � � 4 • 146 · About your vehicle ·

Important note Important note In the event of a failure of one of the onboard systems, signalled In low- to medium-grip conditions (e.g. wet, icy, sandy roads), by the relative warning light on the TFT display, the switch do not deactivate the CST system. moves to a “recovery” position, but still allows the vehicle to be driven. In these cases, contact the Ferrari Service Network. When the CST system is active and the amber warning light comes on, it means that there is a fault in one of the CST system components. Driving modes that can be selected with “Manettino” COMFORT mode Important note This is the maximum safety driving mode. It is recommended for Every time the engine is started, the CST system will reactivate. everyday driving. SPORT mode This is the ideal setting for vehicle performance. Important note Select SPORT mode for sports-style driving, under high-grip The CST system reactivates automatically, even in even in CST conditions. mode when the brake pedal is pressed. Activation will be signalled by the SPORT icon in the dedicated area on the TFT display. CST-OFF mode Select this mode to deactivate the CST system (always active when the engine is started). When the system is deactivated, the relative warning light A illuminates on the instrument panel and the relative ASR/CST failure warning light will be shown on the TFT display for 5 seconds. When the CST feature is active, the warning light A starts flashing on the instrument panel and the relative warning light on the TFT display illuminates. · About your vehicle · 4 • 147

Horn control “UP” shift paddle The horn can be used by pressing the horn symbol, on either side Pull the right-hand UP paddle towards the steering wheel to shift of the steering wheel upper spokes. gears up. “DOWN” shift paddle Pull the left-hand DOWN paddle towards the steering wheel to shift gears down. ���� �� 4 • 148 · About your vehicle ·

Windscreen and headlight washer/wipers Windscreen washer This is activated by pulling lever A towards the steering wheel Important note (automatic return). When the windscreen washer is activated, the windscreen wiper The windscreen wipers and washer work only with the ignition starts automatically. key in position II. Releasing the lever stops the jet of fluid while the blades continue to wipe for a short time. The lever A has 5 settings: OFF Windscreen wipers stationary. Warning AUTO Automatic operating. In this position, the rain sensor's Do not start the windscreen washer during the cold months sensing range can be adjusted (lever pushed down to until the windscreen has warmed up. If it has not warmed up, first click position). the fluid could freeze on the glass and block the view. 1 Slow continuous operation (lever pushed down to second click position). Headlight washer (optional) 2 Fast continuous operation (lever pushed down to third The headlight washer is activated automatically when the click position). windscreen washer is operated and the low beams are on. Lever up Fast temporary operation (automatic return). The headlight washer and windscreen washer share the same fluid tank and a low fluid level is indicated by the relative warning light on the TFT display. � � · About your vehicle · 4 • 149

Cruise control The device can only be activated in 4th or 5th gear. When going down slopes with the device on, the vehicle speed may increase This is an electronically controlled driving assistant that allows slightly more than the memorised speed. the driver to drive the vehicle at a constant speed from 30 km/h Memorising vehicle speed - 200 km/h without keeping the accelerator pedal pressed. Proceed as follows: - turn the ring nut A to ON and bring the vehicle to the desired Important note speed by pressing the accelerator pedal We recommend using the device on long, dry stretches of road - turn the ring nut B upwards (+) for at least three seconds, then with few gear changes (e.g. motorways). release it: the vehicle speed will be memorised and you can Do not use the device for city driving. release the accelerator pedal If necessary, you can accelerate by pressing the accelerator pedal: Activating the device when the pedal is released, the vehicle will return to the speed Turn the ring nut A to the ON position. already memorised. When it is activated, warning light D comes on on the instrument panel and a warning light and associated message appears on the Resetting the memorised speed TFT display. If the device has been turned off by pressing the brake pedal or clutch, for example, to reset the memorised speed, proceed as follows: - gradually accelerate until the vehicle reaches a speed that is near to the memorised speed � - insert the gear selected when the speed was memorised ( 4th or 5th gear) and press the Recall button C. Increasing the memorised speed � This can be done in two ways: - by pressing the accelerator and memorising the new speed reached � or - turning the ring nut B upwards (+). 4 • 150 · About your vehicle ·

Each time the ring nut is turned corresponds to an increase in Rain sensor speed of approximately 2 km/h whereas if the ring nut is kept up The rain sensor automatically adjusts the windscreen wiper timing the speed varies continuously. to the intensity of the rain during intermittent operation. All functions controlled by the right-hand lever are unaffected. Reducing the memorised speed The rain sensor automatically activates when the right-hand lever is This can be done in two ways: moved to AUTO and it has a range of adjustment which runs from - by deactivating the device and then memorising the new speed “wiper stationary” (when the windscreen is dry) to “fast continuous or operation” (with heavy rain). - by turning the ring nut B downwards (-) until it reaches the new To regulate the frequency of intermittent operation, with the lever speed that will be automatically memorised. set to AUTO, turn the control C. Each time the ring nut is turned corresponds to a decrease in speed Turning the end knob counterclockwise, intermittent operation of approximately 2 km/h whereas if the ring nut is kept down the varies from a maximum (fast intermittent operation) to a minimum speed varies continuously. (slow intermittent operation). Deactivating the device Important note Turn the ring nut A to OFF or the ignition key to position 0. The The rain sensor function is reset by turning the ignition key to device is then automatically deactivated in one of the following position 0 and also by leaving the right-hand lever in position ways: AUTO. To reactivate it, turn the control to OFF and then again - by pressing the brake pedal or the clutch. to AUTO. Warning When driving with the device activated, do not put the shift paddle in neutral. Warning If the device is malfunctioning or faulty, turn the ring nut to OFF and contact the Ferrari Service Network. · About your vehicle · 4 • 151

Driving the vehicle Warning Before cleaning the front windscreen (for example in service Running-in stations) make sure the rain sensor is deactivated or that the key The latest manufacturing techniques have allowed us to achieve is at position 0. The rain sensor must be deactivated also when high precision and accuracy levels in the construction and assembly washing the vehicle by hand or in automatic car washes. of components. Nonetheless, the vehicle movable parts undergo a In case of ice or snow on the front windscreen, do not activate settling process, basically during the first hours of operation. the rain sensor to avoid damaging the wiper motor and/or blades. Engine and transmission Avoid exceeding 5,000 RPM for the first 1,000 km (620 mi.). Rain sensor failure After starting, do not exceed 4,000 RPM until the engine has warmed up (oil temperature: 65-70 °C - (149-158 °F)). In the event of a malfunction occurring when the rain sensor is active, the wipers will be set to intermittent operation and the Do not let the engine run at a constantly high speed for a sensing range will be set by the driver, whether there is rain on the prolonged time. windscreen or not. In this case, we recommend that you deactivate the rain sensor and turn on the wipers, if necessary, in continuous Warning mode. BEFORE YOU DRIVE Important note Check that the seat belts are fastened Check that the doors are closed Contact the Ferrari Service Network as soon as possible. Check that the seat is properly adjusted Check the rear-view mirror adjustment (central and sides). 4 • 152 · About your vehicle ·

Before a trip Refilling Preliminary checks Check the following at regular intervals and always before long Warning trips: Use unleaded fuel only! - tyre pressure and condition Using leaded fuel would permanently damage the catalytic - levels of fluids and lubricants converters. - condition of the windscreen wiper blades - proper functioning of the warning lights and external lights. For specifications and quantities of lubricants and fluids, observe the information in the “Refilling” table. Important note In any case, it is advisable to perform these checks at least every 1000 km (620 mi.) and always comply with the maintenance schedule. It is also advisable to: - clean the glass covers of the external lights and all the glass surfaces - properly adjust the mirrors, steering wheel, seats and seat belts. · About your vehicle · 4 • 153

Starting and driving the vehicle (DCT gearbox) System start-up Important note When the ignition key is turned to position II, the DOT MATRIX BEFORE YOU DRIVE gearbox display and failure warning light A are turned on. The If the warning light A continues flashing without going off, switch warning light will turn off if no problems are detected within a few off the system and wait for the gear display to go off before seconds. restarting. The letter P (Parking) or N (Neutral) will remain highlighted on the If the failure persists, contact the Ferrari Service Network. display. If the warning light A is faulty, a warning light will appear on the TFT display (see page 143) and this condition will be indicated by an acoustic alarm when the ignition key is turned to position II. Warning Contact the Ferrari Service Network. � 4 • 154 · About your vehicle ·

Operation with the engine off Once the “System start-up” stage has been completed, the engaged gear will appear on the DOT MATRIX display: Important note N (Neutral) The vehicle is equipped with an electro-hydraulically controlled P (Parking); gearbox system by means of paddles on the steering wheel. R (Reverse); The default setting for the DCT gearbox is always “Automatic” 1 (1st gear); mode. 2 (2nd gear), etc. Every time the vehicle is started, the DCT gearbox is in “Auto easy exit” mode unless the vehicle was in “Automatic” mode Important note when it was turned off. Immediately release the UP and DOWN paddles and the button To exit the “Auto easy exit” mode operate the UP or DOWN R after the display shows that the gear has been engaged; a paddle (while the vehicle is moving) or press the AUTO button prolonged manoeuvre would cause the failure warning light to on the central console. turn on (see page 143) and triggering of the buzzer. Important note If the engine compartment lid is open or not properly closed, none of the gears can be engaged. When the vehicle is stationary, with the driver-side door open or not properly closed and the brake pedal released, the system disengages the gear ���� �� engaged after approximately two seconds. · About your vehicle · 4 • 155

Starting the engine If the engine does not start, turn the key back to position 0 and Before starting the engine, make sure that the antitheft system wait for the gear display to go off before repeating the whole and the electrical devices that absorb a great deal of power are operation. deactivated. If the engine fails to start after several attempts, check for one of • Make sure that the electric parking brake is applied and that the the following causes: doors are closed. • insufficient speed of the starter motor (flat battery) • Hold the brake pedal down when starting the engine. • ignition device faulty • electrical contacts faulty Warning • fuel pump fuses blown. Do not press the accelerator pedal. Warming up the engine Do not run the engine at high speeds until the engine oil temperature • Turn the ignition key to position II and wait for the “Check OK” has reached at least 65-70 °C (149-158 °F), approximately. icon to appear on the TFT display. Starting the vehicle • If the “Check OK” symbol does not appear, turn the key back to With the engine started, the vehicle standing and the brake pedal position 0, wait a few seconds and repeat the procedure. pushed, pull the right-hand “UP” paddle towards the steering • Press the ENGINE START button (see page 146) and release it wheel to engage the 1st gear. as soon as the engine starts. Release the brake pedal and press the accelerator to start off. • After the engine has started, the “Check OK” will appear. With the engine running and the vehicle stationary, you can change Do not hold the ENGINE START button pressed down for a long directly from 1st or 2nd gear to “R” (reverse) by pressing R and from time. reverse to 1st by moving the “UP” paddle. If the engine does not start, turn the key back to position 0 and wait for the gear display to go off before retrying. Warning If the “UP” and “DOWN” paddles are not working, the message Warning “Depress brake pedal and press LAUNCH to engage gear” will Hold the brake pedal down while starting the engine. appear on the TFT display. You can therefore engage the gear by pressing the Launch button (see page 166) and the brake pedal. In these cases, the Launch control function is not available. If the engaged gear was R, the Launch button must be pressed twice to engage the 1st gear. 4 • 156 · About your vehicle ·

UP-shifting Important note Use the right-hand “UP” paddle without releasing the accelerator When reverse is selected, an acoustic safety signal beeps pedal. intermittently as long as “R” is engaged. An UP-shift request is not accepted when engagement of the requested gear forces the engine to underrev or if an UP-shift is already in progress due to engine overrevving. If the system automatically selects 2nd gear when attempting to shift from R to 1st gear, this indicates that 1st gear has jammed.Therefore, Gearshifting will be much quicker if the request is made with this is not a malfunction, as it falls within the system operation the accelerator pedal pushed right down and the engine at over 5,500 rpm. logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has jammed. In any event, it is advisable to: • Gearshift without releasing the accelerator pedal if pressed. During prolonged stops with the engine running, it is advisable to keep the gearshift in “N”. • Wait until gearshifting has been completed before requesting the next shift, avoiding a rapid sequence of multiple requests. Important note UP-shifting due to overrevving On downhill stretches, if you allow the vehicle to move forward in The system “automatically” engages a higher gear if the accelerator N, when UP or DOWN is requested, a gear will be engaged that pedal is pressed and the engine approaches the “runaway speed corresponds to the speed of the vehicle. rate” (overrevving). Important note This condition does not occur with the system in “SPORT” mode. � · About your vehicle · 4 • 157

DOWN-shifting Switching off the engine Use the left-hand “DOWN” paddle, even without releasing the The engine can be switched off either with the gearbox in “N” or accelerator pedal. with a gear engaged. A DOWN-shift request is not accepted if engagement of the After turning the ignition key from position II to position 0, the requested gear forces the engine beyond a certain number of display will remain on for a few more seconds to display the gear revolutions, depending on the gear requested, or if a DOWN-shift engaged. If the gearbox is in “N” a buzzer will sound. is already in progress because of underrevving. In any event, it is advisable to: Warning • Gearshift without releasing the accelerator pedal if pressed. Never leave the vehicle with the gearbox in “N”. Make sure that • If “DOWN-shifting” is requested to start overtaking which the letter “P” appears on the display. requires quick acceleration, press the accelerator pedal just before using the paddle. • Wait until gearshifting has been completed before requesting the Warning next shift, avoiding a rapid sequence of multiple requests. Never leave the vehicle with the engine running. “DOWN-shifting due to underrevving” • The system down shifts “automatically” if the engine goes below a minimum number of revs of 1250 rpm. Important note • The DOWN-shift request from the paddle ignored if gearshifting If the vehicle is not in Parking mode (“P” must be displayed on is already in progress because of underrevving. the DOT MATRIX display), the key cannot be removed. “N” (Neutral) request For information on the electronic parking brake, see page 167. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. 4 • 158 · About your vehicle ·

“Automatic gearbox” mode “Auto easy exit” gearbox mode This mode is activated (or deactivated) using the AUTO switch; the The vehicle is always started in “Auto easy exit” mode, unless it was word “AUTO” will light up on the gear display and the system will turned off with the gearbox in “Automatic” mode. automatically adjust UP-shifting and DOWN-shifting according to Activation is indicated by the word AUTO on the gear display on the vehicle speed, engine speed and torque/power request of the the instrument panel. driver. The system will automatically UP-shift and DOWN-shift according Gearshifting is possible using the “UP” and “DOWN” paddles but to vehicle speed, engine revs and the torque/power request of the the system remains in “Automatic” mode. driver. To exit the “Automatic” mode, you must press the AUTO switch In “Auto easy exit” mode, if you operate the UP and DOWN until the “Automatic” warning light goes out. paddles (while the vehicle is moving) the system will exit the When the vehicle stops, the request for “N”, 1st or “R” does not “Automatic” mode and go into “Manual” mode. change the mode from “Automatic” to “Normal”. If the “Automatic” gearbox mode is then requested by pressing the AUTO button, the system will apply all the characteristics of the “Automatic” gearbox mode. Push start Warning Push starting is not allowed. · About your vehicle · 4 • 159

Safe driving While travelling For safe driving, it is essential that the driver be aware of the best - Caution is the number one rule for safe driving, which also means driving techniques suited to various circumstances. Always try to you should take other people’s behaviour into consideration. prevent dangerous situations by driving with caution. - Follow the Road Regulations in force in the country you are Before you drive driving in and always respect the speed limit. - Adjust the position of the seat, steering wheel and rear-view - Always make sure that the driver and the passenger have their mirrors, in order to obtain the best driving position. seat belts fastened and that all children are travelling in suitable - Adjust the backrest so that your chest is upright and your head is child seats. as close to the headrest as possible. - Good personal physical conditions ensure you can drive long - Carefully adjust the headrest so that your head, and not the neck, distances safely. is resting against it. Ensure that nothing (e.g. mat covers, etc.) is blocking the pedals. - Check that the lights and headlights are working properly. - Ensure that any child restraint systems (e.g. child seats, cradles etc.) are properly fixed on the passenger seat. - Your reflexes are quicker if you eat lightly before driving: avoid heavy meals before a trip. - Do not drink alcoholic drinks before and during the journey. At regular intervals, check the following: - Tyre pressure and condition - Engine oil level - Engine coolant level and system condition - Brake fluid level - Steering fluid level - Windscreen washer fluid level. 4 • 160 · About your vehicle ·

Driving at night Warning When you are travelling at night, follow these fundamental rules: Driving under the influence of drugs or certain medications is - Reduce speed, particularly on dark roads. dangerous to yourself and others as well as contravening road - Driving conditions are more demanding at night, so take regulations and legal norms. particular care. Travelling without your seat belt fastened increases the risk - If you start feeling tired or sleepy, stop immediately: to continue of serious injury and death in the event of a collision. Always driving would be a risk for yourself and for others. Continue only fasten the seat belt and the child seat, if any. after you have had a rest. Deactivate the passenger’s airbag (where possible) if a child seat - At night, it is difficult to evaluate the speed of the vehicles in front is fitted on the front seat. of you by seeing their lights only: keep at a greater safety distance Do not travel with objects lying around on the floor, especially than you would during the day. in front of the driver’s seat: in the event of braking, these - Use the high beams only outside of urban areas and when you are could slide under the pedals, making it impossible to brake or sure that they will not disturb other drivers. accelerate. - Turn off the high beams when you see oncoming vehicles and use Additionally, ensure that any loose floor mats sit correctly. the low beams. Water, ice and salt spread on icy roads may deposit on the brake - Keep the lights and headlights clean. discs and reduce the efficiency of the initial braking. - Watch out for animals crossing the road when travelling outside urban areas. - Make regular stops to loosen up your limbs and refresh yourself Driving in the rain and avoid driving for hours on end. Rain and wet roads can cause hazardous situations. - Keep a constant air circulation in the passenger compartment. All manoeuvres are more difficult on a wet road, as the tyres have - Never coast downhill with the engine off: in these conditions significantly less grip on the road. This means that the braking the engine brake, servo brake and power steering are inefficient, distances increase considerably and road-holding decreases. braking requires greater pressure on the pedal and steering will be harder. Below is some advice for driving in the rain: - Keep a greater safety distance between yourself and the other vehicles and reduce your speed. · About your vehicle · 4 • 161

- When it is raining very hard, visibility is also reduced. In these Driving in fog cases, to make yourself more visible to others, turn on the low Whenever possible, avoid setting off if the fog is thick. If you have beams even during the day. to drive in misty conditions, or if there is thick fog or fog banks, - Do not drive through puddles at high speeds since you do not follow these rules: know how deep they may be; Travelling through a puddle at high - Keep a moderate speed. speed can result in losing control of the vehicle (“aquaplaning”): - Turn on the low beams, also during the day, and use the rear fog if this occurs, grip the steering wheel firmly. light. Avoid using the high beams. Warning Warning If the road is wet, reduce your speed to avoid “aquaplaning” On stretches where visibility is good, turn off the rear fog light, (during which the tyre no longer touches the road surface. This it may be annoying for the occupants of the vehicles behind is due to the fact that, when the road is very wet and vehicle you. speed is high, because of their particular shape or insufficient depth, the side channels of the tyre tread are not capable of removing all of the water channelled so that a layer of water is - Remember that fog makes the road damp and therefore all placed between the road surface and the tyre. The fluid pressure manoeuvres are more difficult and braking distances are longer. generated is so high that it supports the vehicle's weight making - Keep a safe distance from the vehicle in front of you. it virtually impossible for the driver to control the vehicle). - As far as possible, avoid suddenly changing speed and direction. - As far as possible, avoid overtaking. - Use the ventilation system to demist the windscreen (see - In the event of an emergency stop, (e.g. failures, inability to page 174) and avoid visibility problems. proceed due to poor visibility conditions, etc.) try to free the - Periodically check the condition of the windscreen wiper blades. main driving lane. Then turn on the hazard warning lights and, if possible, the low beams. On approaching another vehicle, sound the horn rhythmically. 4 • 162 · About your vehicle ·

Driving on mountain roads Driving with the “ABS” braking system Below is some advice for driving on steep mountain roads: The ABS system assists the driver as follows: - To prevent the brakes from overheating when driving downhill, - It prevents the wheels from locking and skidding during use the engine to brake by engaging a lower gear. emergency braking, particularly in low-grip conditions. - Never coast downhill or drive downhill with the engine off or - It allows braking and changing direction at the same time. This in neutral, nor with the ignition key removed from the steering feature is affected by the physical limits and lateral grip of the column. tyres. - Drive at a moderate speeds and do not “cut” corners. - When the ABS is activated, you will feel a slight pulsing of the - Remember that overtaking uphill is slower and requires a longer brake pedal during emergency braking or in low-grip conditions. free stretch of road. If you are overtaken when driving uphill, Do not release the pedal but continue to push it to give continuity ensure that the other vehicle can pass easily. to the braking action. Driving on snowy or icy roads - The ABS prevents the wheels from locking, but it does not increase the physical limits of grip between the tyres and the road: Below is some advice for driving in these conditions: keep a safe distance from the vehicles ahead and reduce speed - Keep a very moderate speed. before curves. - Keep a safe distance from the vehicles in front of you. - Fit snow tyres approved for the vehicle. - Given the poor grip, use the engine brake as much as possible and avoid sudden braking. - Avoid sudden acceleration and sharp changes in direction. - During the winter season, even apparently dry roads can have icy sections. Therefore, be careful when driving along stretches of road in the shade as there may be icy patches. · About your vehicle · 4 • 163

Driving using the driving mode control switch (“Manettino”) For this reason, the suspension damping level is shifted to a The driving mode control switch A on the steering wheel, allows higher one, so as to enhance performance, handling and stability at high speeds. the driver to use the vehicle potential in a quick and easy way. There are three modes available which can be selected according to the grip level (from low to high) and consequently the level of driving assistance required (from high to none). - The COMFORT mode is for driving in maximum safety in all conditions and particularly in low grip situations. It is recommended for everyday driving. If the COMFORT mode is selected, it is indicated on the TFT display as follows: - The SPORT mode is the vehicle driving mode that provides the best compromise between stability and performance. This setting ensures stability only in medium- to high-grip conditions and not on low-grip road surfaces (in this case, it is advisable to return to Low Grip mode). In this mode, the vehicle maximum performance can be experienced on open roads. If the SPORT mode is selected, it is indicated on the TFT display as follows: � 4 • 164 · About your vehicle ·

- The CST is deactivated. Vehicle stability is no longer controlled, - With the engine running, select the first gear but is completely in the hands of the driver. The only auxiliary - Select neutral “N” systems still active are those that cannot be deactivated such as - Switch off the engine ABS and EBD. - Turn the key to key-on 3 seconds after switching off If the CST mode is deactivated, it is indicated on the TFT display as follows: - The message “Carwash mode activation” will appear on the TFT display. Park Lock The Park Lock is a locking device built into the gearbox. This device is used to prevent the vehicle moving when the multi- disc clutches are open, i.e., with the engine off and/or without the hydraulic pressure needed for the gearbox. This device operates automatically at each key off and “P” appears on the DOT MATRIX display. If there is a system failure, refer to “Emergency unlocking of Park Lock” on page 214. Carwash procedure Ignition switch The Park lock emergency device can be electronically deactivated on a temporary basis by performing the Carwash procedure. The ignition key can be turned to 2 positions: This procedure is necessary when the vehicle has to be moved with Position 0 - Stop the engine off and when washing the vehicle. Engine off, key removable. When the key is even only partially extracted, the steering column Warning is locked. When the Park Lock safety device is electronically disabled The hazard warning lights and the parking lights can be activated. (Carwash procedure), the vehicle may move unexpectedly! To facilitate steering wheel release, turn the steering wheel slightly The vehicle is only kept stationary by the parking brake which in both directions while turning the ignition key. must be applied. · About your vehicle · 4 • 165

Position II - Ignition Launch Turning the key to this position, the TFT display will check the The “Launch” mode is a performance start function. Activating this signals coming from the vehicle systems. function gives the vehicle the best possible acceleration. If no malfunctions are found after starting up, the words The device transfers the necessary torque to the ground and avoids “Check OK” will be displayed. skidding of the wheels during acceleration. The “Launch” mode is activated as described below: Warning - the vehicle must be stationary Always remove the key from the ignition when you get out of - gearbox must be in manual mode the vehicle! - select the first gear Never leave children unattended in the vehicle. - press button L to the left of the centre console - press the accelerator pedal and release the brake pedal. Key lock If more than 20 seconds elapse after turning the key to position 0, Important note the key lock device must be released to remove the key: press button K and remove the key at the same time. The Launch control function is not available in presence of: - a sloping road surface, even slight - high clutch temperatures. � � �� � 4 • 166 · About your vehicle ·

EPB - Electronic parking brake Seat adjustment The parking brake is controlled by a small electric engine. It can be applied and released using the special control A on the Warning dashboard to the left of the steering wheel. Never adjust the seat while driving; you may lose control of the The brake is automatically activated when the engine is switched vehicle. Adjust the driver’s seat only when the vehicle is stationary. off and can be temporarily deactivated by pressing button B. Pushing down the brake pedal and pressing button A deactivates it Correct adjustments are very important for a better driving comfort automatically. and for the maximum efficiency of the passive safety systems. The electric parking brake can operate as an emergency brake when The seat position can be electrically adjusted using the special the vehicle is in motion. controls. If this is the case, the electric parking brake communicates with Three adjustments are possible using control D: the ESP system to prevent locking. The warning light will turn off - forward/backward adjustment: push the control forward or when the parking brake is fully released. backward - height adjustment: push the control upward or downward Warning - seat inclination (tilting): push the front end of the control upward Always apply the parking brake when the vehicle is parked. or downward to adjust the inclination of the front part of the seat The vehicle should be blocked. If this is not the case, please cushion; push the rear end of the control upward or downward to contact the Ferrari Service Network. adjust the inclination of the rear part of the seat cushion. � � � · About your vehicle · 4 • 167

Seat back rake adjustment Seat position memory (2+2 version and Full Electric option) Use control E to adjust the seat back rake. Push the control forward When a front door is open at key-off (key in position 0), the seat or backward to adjust the seat back rake. can be moved for a limited period (approx. 15 sec.). Each time a door is opened or both doors are closed at key-off, the seat can be Lumbar support adjustment (Full Electric option) moved again for a limited period. Use control F to adjust the lumbar support. Push the control on the The seat position can only be memorised at key-on (key in seat symbols to increase or decrease the lumbar support. position II), by pressing one of the three buttons 1, 2 or 3 (H) each corresponding to a memorisable position. Pressing one of these buttons for longer than 3 seconds memorises the position of the Backrest and cushion side width adjustment (Full Electric option) driver seat, rear-view mirror and steering column (confirmed by Use control G to pneumatically adjust the width of the backrest emission of a double tone). sides and the seat cushion. Push the control on the seat symbols to To recall the memorised position, press one of the buttons H and increase or decrease the side width. release it within 3 sec. Operating begins as soon as the button is released. Recalling the memorised position is not allowed when the vehicle is in motion. If the vehicle starts to move while the memory recall is being operated, the seat and column do not stop moving and reach the memorised position. � � � 4 • 168 · About your vehicle ·

If the memorised backward/forward position of the passenger seat Tilting the backrest is less than approximately 50 mm from the rear stop, when the seat To tilt the seat, pull lever L up and push the backrest towards the position is recalled from another backward/forward adjustment, front of the vehicle. the seat stops once it is approximately 50 mm from the rear stop. When the backrest goes back into position, it will automatically The position can be adjusted by using the backward/forward block once it has reached the correct position. adjustment control. To facilitate access to the rear seats or exiting the vehicle, the With reverse gear engaged, the position of the passenger external front seats are equipped with the “rear seat Easy Entry” device rear-view mirror can be adjusted by the user to a position other (only operative when doors are open or vehicle is stationary), than the driving position to help when parking. This position can which moves the seats forward to the front stop and lowers them be memorised along with all the other memorisable positions. automatically when the relative backrests are lowered and returns If the personalised reverse gear position is never set, when the them to the original position when the backrests are lifted again. reverse gear is engaged, the passenger external rear-view mirror If the initial backward/forward position of the passenger seat is less will be positioned slightly downwards and inwards (compared with than approximately 50 mm from the rear stop, during the return the driving position). the seat will stop at 50 mm from the rear stop. The position can be adjusted by using the backward/forward adjustment control. � � · About your vehicle · 4 • 169

Headrest adjustment Adjusting the steering wheel Place the headrest at a height that corresponds to the height of the The steering wheel is electrically adjustable for rake and reach. It occupant. To raise the headrest, simply pull it up. can only be adjusted if the ignition key is in position II. To lower the headrest, press button M. Move control A (to the left of the steering column) in the four Seat heating system (Full Electric option) directions to adjust the steering wheel. Turn control N to activate the seat heating function. The steering wheel position is memorised, together with the position of the external rear-view mirrors, when the driver’s seat When this function is active for one or more seats, the relative position is stored. warning light on the instrument panel illuminates. Using control N, the driver can adjust the heating, choosing from 3 levels identified on the control with the numbers 1, 2 and 3. In position 0, seat Warning heating is not activated. Do not adjust the steering wheel while driving. Driver seat Easy Entry/Exit (2+2 version and Full Electric option) To help the driver to get in and out of the vehicle, the driver seat To help the driver when entering or exiting the vehicle, the steering Easy Entry/Exit function is activated (only operative when the wheel is lifted automatically. door is open and the key is in position 0) which moves the steering wheel column upwards. When the door is closed and the key is in position II, the steering wheel column returns to its original position. � � � 4 • 170 · About your vehicle ·

Rear-view mirrors External rear-view mirrors Internal electrochromic mirror These mirrors can be electrically adjusted using the control C (with the ignition key in position II) and are equipped with defogging The internal electrochromic mirror automatically darkens to reduce elements. the dazzling effect of the reflected light on the driver. The speed 1) Mirror selection: using control C select the mirror you wish to with which the mirror darkens depends on the intensity of the light. adjust (right- or left-hand). 2) Mirror positioning: move control C in the four directions (up – down – right – left) to adjust each of the rear-view mirrors. Once adjustment is complete, move the control C into the upper central position, where it will be locked in order to avoid changing the setting inadvertently. The mirrors will yield in both directions in the event of a collision: if necessary, the mirrors can be pushed both backwards and forwards. In the models equipped with memory seats, every time the seat position is memorised, the external rear-view mirror position is also stored automatically, both for the normal travelling direction and for reverse manoeuvring. � � · About your vehicle · 4 • 171

To memorise a new position of the external rear-view mirrors, Air conditioning and heating system turn the ignition key to position II and adjust the position of the mirrors; then engage reverse and reposition the external mirrors to ensure the best possible visibility to perform the manoeuvre, then Operating modes disengage reverse gear. Automatic Finally, press one of the buttons 1, 2 or 3 on the seat (see page This mode automatically adjusts the air distribution, temperature 168), each one corresponding to a memorisable position, until a and ventilation levels according to the temperature set by the user. double tone confirms the procedure is complete. Partially Automatic The new position of the external rear-view mirrors will be This mode allows the user to adjust certain parameters manually, automatically memorised together with the seat position. while others remain automatic. In addition, the mirror positions can be adjusted for both the Manual normal travelling direction and for reverse manoeuvring. This mode allows the user to set the values to suit the passengers’ The mirrors must always be in the open position while driving. needs. 4 • 172 · About your vehicle ·

Controls Left-hand temperature setting and AUTO button (1) 1 Left-hand temperature setting and AUTO button This is used to select the required air temperature in the left-hand 2 A.C. compressor activation/deactivation side of the passenger compartment; the AUTO button is used to activate automatic operating (LED on). 3 Single-zone operating activation/deactivation A.C. compressor activation/deactivation (2) 4 Air distribution fan speed This is used to activate (LED on) or deactivate (LED off) the A.C. 5 Rear screen demist activation/deactivation compressor. 6 Windscreen demist activation/deactivation Single-zone operating activation/deactivation (3) 7 Right-hand temperature setting and AUTO button This is used to activate (LED on) or deactivate (LED off) single- 8 Right-hand air distribution mode setting zone operating. 9 Air recirculation 10 Left-hand air distribution mode setting � � � � � � � � � � �� � � · About your vehicle · 4 • 173

Air distribution fan speed (4) Right-hand temperature setting and AUTO button (7) The four setting positions allow the occupants to select the air flow This is used to select the required air temperature in the right-hand rate. side of the passenger compartment; the AUTO button is used to Rear screen demist activation/deactivation (5) activate automatic operating (LED on). Press this switch (LED on) to activate rear screen defogging/ Right-hand air distribution mode setting (8) demisting. This is used to select one of the six air flow distribution modes in Windscreen demist activation/deactivation (6) the right-hand side of the passenger compartment. Press this switch (LED on) to activate windscreen defogging/ demisting. � � � � � 4 • 174 · About your vehicle ·

Air recirculation (9) If released (LED off) ; the air flow comes from the outside. Important note When outside temperatures exceed 32 °C (90 °F), the air The air coming out of the vents does not correspond to the recirculation feature remains on with a 60-second pause every temperature requested by the user, but is the temperature twenty minutes, to refresh the air. required to maintain the desired temperature inside the If you activate the windscreen washer function, the air recirculation passenger compartment. feature activates for 20 seconds, to prevent any smell of detergent products from entering the passenger compartment. Adjusting the air vents If pressed (LED on), the air flow comes from inside the passenger The adjustable air vents are positioned on the sides and in the compartment. central section of the dashboard. The recirculation increases air heating or cooling. Directing the air flow A. Left-hand air distribution mode setting (10) Air flow rate B. This is used to select one of the six air flow distribution modes in Turned counterclockwise: open. the left-hand side of the passenger compartment. Turned clockwise: closed. Once the internal temperature has stabilised at the desired level, you are advised not to change the position of the temperature Important note selection switch unless the external temperature changes drastically. It is advisable to keep the air flow rate B set to open and to direct the air flow to a neutral position A. � � �� � · About your vehicle · 4 • 175

Maintenance To close the glove compartment, push the top part until you hear The pollen filter must be replaced every year, as indicated in the the click of the lock. “Maintenance Schedule”. Pocket-change compartments Sun radiation sensor They are located on the lower part of the doors and on the centre This sensor is positioned on the dashboard and optimises console. ventilation and temperature control inside the passenger Ashtray compartment depending on the incidence angle of the sun rays. To access the ashtray G, lift the lid back. Passenger compartment accessories To clean the ashtray, remove it by pulling it up. Glove compartment This is located on the passenger side of the dashboard. To open it, pull lever C and the glove compartment will move down slowly by way of a damped opening mechanism. The glove compartment is illuminated by a light which turns on automatically when the door is opened. Warning Keep the glove compartment closed while driving. � � 4 • 176 · About your vehicle ·

Sun visors Placing suitcases in the luggage compartment The sun visors can be moved by pulling them down towards the The luggage compartment secures the load in the luggage windscreen. compartment and prevents the hard top from blocking when There is a mirror on the back of the passenger-side visor. operated. Make sure you have closed the partition correctly so that Flaps communicating with luggage compartment it is blocked correctly both on the left and the right. To access the luggage compartment from the passenger compartment, open one or both rear flaps F and lower them onto the seats. Warning Do not place items above the partition: this is to avoid the risk of causing serious damage to the opening and closing mechanisms. Warning Do not place objects in the folded roof compartment: this is to avoid the risk of causing serious damage to the opening and closing mechanisms. � · About your vehicle · 4 • 177

2 + 2-seater version Warning Do not place objects on or next to the partition between the Warning luggage compartment and the folded roof compartment when closed. Do not place luggage above the level of the closed Place the light luggage as far down and as far forward as partition. possible. Place the heavy luggage in the lowest well of the luggage compartment as far forward as possible so that it touches the Important note edge of the well. (Position A). If possible, use the eyebolts to fasten the luggage with clamps Do not place the luggage in unstable positions (Position B). or rope. � � �� �� 4 • 178 · About your vehicle ·

2-seater version Warning Warning Rear shelf Place the light luggage as far down and as far forward as Only place light luggage here and secure it using the special possible. belts. Place the heavy luggage in the lowest well of the luggage compartment as far forward as possible so that it touches the edge of the well. (Position A). Do not place the luggage in unstable positions (Position B). � � �� �� · About your vehicle · 4 • 179

Wind deflector - Fit part A onto part B as shown in the figure. The wind deflector can be used when driving with the retractable hard top open. It reduces wind buffeting in the passenger compartment and offers even more pleasant trips at higher speeds too. The deflector is stored in a special bag in the luggage compartment. � Fitting The deflector is divided into two parts: A and B. - Take part A and open it as shown in the figure � � Important note Make sure that the hook 1 has been correctly inserted. � Lock the fastenings 2 on the right and left of the deflector B. - Take part B and open it as shown in the figure � � 4 • 180 · About your vehicle ·

� � � � - Push the pin 3 until it snaps into place. � � � Warning - Place the deflector with supports 4 in the special slots on the left and right of the vehicle and pin 3 in the special hole on the right When the deflector is fitted, do not tilt the front seats too far of the vehicle. back if they are moved right back into the end stop position to avoid damaging the deflector. Important note Pay attention to the vehicle trim. Warning Check that the deflector has been secured correctly! - Push the other snap-in-place pin 3 into the special hole on the left of the vehicle. · About your vehicle · 4 • 181

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Toolkit Warning Tool bag Repair work using the toolkit requires: Housed in the luggage compartment, it contains the necessary tools - suitable protective equipment (e.g. gloves); to make a first repair in the event of a failure: - adequate precautions to be taken (e.g. during tyre replacement • set of flat wrenches; never lie under a vehicle raised by a jack); • insulated cutting pliers; - minimum specific expertise when working in contact with electrical parts/components (e.g. battery). • screwdriver for slotted screws; • screwdriver for crosshead screws; • tow hook; • set of light bulbs; • set of fuses; • parking brake manual emergency unlocking key; • “Park Lock” emergency unlocking key; • tyre inflation kit. 5 • 184 · Advice for Emergency Situations ·

Emergency tyre repair and inflation kit In the event of a puncture or low pressure of a tyre, the kit can be Warning used to repair and/or inflate the tyre sufficiently to continue the Punctures cannot be repaired on the sides of the tyre. Do not journey safely. use the tyre repair kit if the tyre has been damaged after driving with a flat tyre. Important note To use the tyre repair and inflation kit correctly, refer to the Warning instruction booklet supplied with the kit. Damage to the wheel rim that causes air leaks cannot be repaired. Do not remove foreign objects (screws or nails) that Warning have penetrated the tyre. Give the instruction booklet supplied with the kit to the personnel that will have to deal with the tyre treated with the Warning repair kit. After using the repair kit, the vehicle must however be considered to be in an emergency situation: drive with the Warning greatest care (maximum permissible speed 80 km/h - 50 mph). In the event of a puncture caused by foreign objects, tyres can be repaired with cuts of up to 4 mm in diameter on the tyre Warning tread and shoulder. Apply the sticker where it can easily be seen by the driver to indicate that the tyre has been treated with the tyre repair kit. Drive carefully especially on bends. Avoid sudden accelerating or braking. · Advice for Emergency Situations · 5 • 185

Warning Warning The kit is to be used to temporarily repair only one tyre The repaired tyre must be replaced as soon as possible and the punctured by small objects: the kit may not be useful in the case workshop personnel must be informed that the tyre was treated of large punctures or tearing. with tyre repair fluid. Important note Warning After driving for approximately 10 minutes, stop and recheck Keep the kit in its box and out of children’s reach. the tyre pressure. Do not inhale or swallow the fluid contained in the cartridge Remember to use the handbrake. and avoid contact with the skin and eyes. Warning If the pressure has dropped below 1.8 bar, do not continue driving: the kit cannot guarantee the correct hold because the tyre is too damaged. Contact the Ferrari Service Network. If the tyre pressure is at least 1.8 bar, restore the correct pressure and continue driving. Drive very carefully to the nearest Ferrari Service Network. 5 • 186 · Advice for Emergency Situations ·

Warning Warning The spray contains ethylene glycol. The sealant in the kit cartridge can damage the sensor inside It contains latex: it may cause an allergic reaction. Harmful the wheel rim on vehicles fitted with a tyre pressure monitoring if swallowed. Irritating to eyes. May cause sensitisation by system. inhalation and skin contact. Avoid contact with eyes, skin and If this occurs, the sensor must be replaced. Contact the Ferrari clothing. In case of contact, rinse immediately with plenty of Service Network. water. If swallowed, do not induce vomiting, rinse mouth, drink plenty of water and seek immediate medical advice. Keep out of reach of children. The product should not be used by asthma Warning sufferers. Do not inhale vapours when using. In the event of an Wear the protective gloves supplied with the tyre repair kit. allergic reaction, seek immediate medical advice. Store the spray can in its special case away from sources of heat. The liquid sealant has an expiry date. Useful accessories In addition to the tools supplied with the vehicle, the hazard Environment warning triangle and fluorescent safety jacket should always be kept on board in order to signal hazardous situations in compliance Replace the spray can containing the expired liquid sealant. Do with regulations. not dispose of the spray can in normal domestic waste. Dispose of in accordance with national and local regulations. · Advice for Emergency Situations · 5 • 187

Replacing the headlight bulbs Disconnect the battery using the quick release. To replace a rear bulb, proceed as follows: Important note • move the luggage compartment strip slightly; • remove the bulb holder N; The low/high beams are equipped with bi-xenon light bulbs. • remove the bulb by pulling it out and replace it; To replace the headlight bulbs, contact the Ferrari Service Network. • put the bulb holder back in place and reposition the luggage compartment perimeter seal strip. To adjust the headlight beam, please contact the Ferrari Service Network. Replacing the supplementary taillight bulbs Replacing the taillight bulbs Important note To replace the supplementary taillight bulbs, contact the Ferrari Important note Service Network. Before replacing a beam bulb, make sure that the fuse is not blown. N 5 • 188 · Advice for Emergency Situations ·

Replacing the number plate light bulb Replacing other light bulbs To replace a number plate light bulb, proceed as follows: Roof panel dome light • unscrew the two lid fastener screws; • Use a screwdriver to gently prise off the edge of the transparent • remove the transparent cover A from its housing and replace the cover C of the dome light and remove it from the roof panel. bulb B snapped in place between the two clips; • Replace the bulb D or E or F • refit the transparent cover and screw up the two fastener screws. • Refit the dome light and make sure that the wires are not pinched by inserting it first from the connector side and then pressing on the opposite side. � � � � � � · Advice for Emergency Situations · 5 • 189

Glove compartment and luggage compartment light Underdoor light • Use a screwdriver to gently prise under the edge of the • Use a screwdriver to gently prise under the edge of the transparent cover G and lift it. transparent cover and lift it. • Completely remove the transparent cover from its housing. • Completely remove the transparent cover from its housing. • Take the bulb out of its clips. • Take the bulb G out of its clips. • Replace the bulb. • Replace the bulb. • Refit the transparent cover and make sure that the wires are not • Refit the transparent cover and make sure that the wires are not pinched by inserting it first from the connector side and then pinched by inserting it first from the connector side and then pressing on the opposite side. pressing on the opposite side. Replace the luggage compartment light bulb in the same way � � 5 • 190 · Advice for Emergency Situations ·

Light bulbs (12 V except for high beam and low beam) Type Power Low beams and high beams gas-discharge (XENON) Das Front running lights LED Front turn indicators LED Side turn indicators incandescent T4W Upper rear headlight LED Number plate lights incandescent R5W Supplementary stop lights LED Fixed part of reverse lights incandescent 16W Running/stop lights on moving part of taillight incandescent 21W/5W Fixed part of rear turn indicators incandescent 21W Rear fog lights incandescent H16W Dome light incandescent 8W Spotlight incandescent 5W Glove compartment light incandescent W5W Underdoor courtesy light incandescent W5W Luggage compartment light incandescent 10W · Advice for Emergency Situations · 5 • 191

Replacing a fuse Use the pliers C in the fuse box in the passenger compartment behind the dashboard to the left of the steering wheel to remove When an electrical device is not working, check that the the fuses. corresponding fuse is not blown. Fuse colour A - Unblown fuse. B - Blown fuse. Ampere yellow ochre 5 Important note brown 7.5 If the problem persists, contact the Ferrari Service Network. red 10 light blue 15 Important note yellow 20 When replacing a fuse, always use fuses of the same amperage white 25 (same colour). green 30 The toolkit contains spare fuses. Maxi fuse colour Ampere yellow 20 green 30 � orange 46 � red 50 blue 60 � 5 • 192 · Advice for Emergency Situations ·

Location of the fuse and relay boxes A - Fuses and relays in engine compartment B - Body Computer fuses and relays C - Fuses and relays in passenger compartment on passenger side D - Fuses and relays in passenger compartment on centre console � � � � · Advice for Emergency Situations · 5 • 193

Fuses and relays in the engine compartment F-72 40 Parking brake power To access these fuses: F-73 70 Dashboard ECU power • open the engine compartment lid • remove the box cover A. Body Computer fuses and relays To access these fuses, remove the flap 1 by unscrewing the two Important note fastener screws. Box B contains the following relays (R) and maxi fuses (MF): Only open the boxes containing the fuses that need to be checked to avoid damaging other components. Important note Box A contains these fuses: Only open the boxes containing the fuses that need to be checked to avoid damaging other components. Ref. Amp. Use CAL2 CAL2 Power supply (starter motor and alternator). F-70 150 Power supply and engine relay F-71 40 Hard top pump � � � 5 • 194 · Advice for Emergency Situations ·

The box A contains the following relays (R) and maxi-fuses (MF): F-52 15 Power socket, driver seat heating Ref. Amp. Use F-53 10 Instrument panel F-12 15 Right high beam T01 20 Low beam relay F-13 15 Left high beam T11 30 Heated rear screen relay F-31 7.5 AC unit, body computer connector T12 30 Relay services 1 F-32 10 Dome lights, foot well and puddle lights, side T13 joint Supply jumper services 2 markers, supplementary taillights. F-35 7.5 Clutch pedal control, Cruise control, Power steering, Beams. F-36 10 Satellite alarm system, parking sensors, fuel filler flap. F-37 10 Stop light control. F-38 15 Luggage compartment lock F-39 15 Radio, diagnosis socket, CAN box interface. F-40 30 Heated rear screen F-42 7.5 Alternator F-43 30 Windscreen wipers F-44 20 Passenger seat heating, cigarette lighter F-46 20 Hard top F-47 30 Driver-side door F-48 30 Passenger-side door F-49 7.5 Passenger compartment lighting switches and controls F-50 7.5 Air bags F-51 7.5 Semi-automatic gearbox, engine start button · Advice for Emergency Situations · 5 • 195

Passenger side fuses and relays Ref. Amp. Use To access these fuses, remove the passenger footrest 2 by F-01 60 +30 Radiator fans (first speed) unscrewing the four fastener screws. F-02 30 +30 ABS (valves) Box C contains the following relays (R) and fuses (F): F-03 30 +30 Ignition switch F-04 50 +30 ABS (pump) F-05 40 +30 Air conditioning and heating system F-06 50 +30 Radiator fans (second speed) F-07 20 +30 Horns F-08 7.5 Air conditioning and heating system compressor F-09 7.5 +30 Supplementary stop lights F-10 15 +30 luggage compartment lock relay F-11 25 Left bank oxygen sensors F-14 15 +30 high beams F-15 7.5 +30 alternator sensing F-16 25 +30 Right bank engine control power supply � F-17 25 +30 Left bank engine control power supply F-18 10 +30 Left cylinder bank injection system power supply, LH cylinder bank injection main relay coil F-19 10 +30 Right cylinder bank injection system power supply, RH cylinder bank injection main relay coil � F-20 30 +30 right injection system main relay F-21 15 +30 Fuel pump 2 5 • 196 · Advice for Emergency Situations ·

F-22 15 Left bank (ignition coil) T16 50 Radiator fan relay (first speed) F-23 10 +30 ABS (electronic) T17 10/20 INT/A relay (devices excluded at ignition) F-24 15 Right bank (ignition coil) T19 30 Stop light control relay. F-30 30 +30 Starting relay T20 30 Starting relay F-81 40 +30 Supplementary ECU power supply T26 30 Windscreen wiper relay (first speed) F-82 70 +30 Dashboard ECU and luggage T27 30 Windscreen wiper relay (second speed) compartment ECU power supply T28 30 Windscreen washer pump relay F-83 50 +30 Air pump relay T29 30 Supplementary stop light relay (third stop light) F-84 15 +30 Fuel pump relay 1 T30 50 Air pump relay F-85 25 Headlight washer T37 30 Left supplementary taillight relay F-87 25 Right bank oxygen sensors T38 30 Left headlight LED module power supply F-88 10 +15 left cylinder bank injection system relay F-93 30 +30 suspension control node fuse T39 30 Right headlight LED module power supply T02 30 High beam relay relay T05 30 Fuel pump relay 2 T31 30 Headlight washer pump relay T06 30 Luggage compartment lock actuator relay T07 50 Horn relay T08 30 Air conditioning and heating system compressor relay T09 30 Left cylinder bank injection system main relay T10 30 Right cylinder bank injection system main relay T14 30 Fuel pump relay 1 T15 50 Radiator fan relay (second speed) · Advice for Emergency Situations · 5 • 197

Fuses and relays on centre console Ref. Amp. Use To access these fuses, remove flap 3 from the centre console. F-54 2.0 +30 HI-FI amplifier Box D contains the following relays (R) and fuses (F): F-56 30 +30 Driving position F-57 7.5 Side Markers 1 (LH front and RH rear) F-59 7.5 Reverse lights F-60 30 +30 Passenger position F-61 7.5 +30 Driving position (electronic) F-62 7.5 +30 Passenger position (electronic) � F-63 15 +30 Semi-automatic gearbox main relay F-64 7.5 Fuel filler flap actuator F-65 20 Door lock actuator F-66 7.5 +30 Semi-automatic gearbox F-67 7.5 Side Markers 2 (RH front and LH rear) F-78 15 +30 Battery charger F-80 30 +30 BassBox amplifier T21 50 Side Marker relay T22 30 Reverse light relay T23 30 Fuel filler flap relay T24 30 Supplementary taillight relay T25 30 Semi-automatic gearbox main relay 5 • 198 · Advice for Emergency Situations ·

Replacing a wheel • additional tool bag C containing: jack and wrench to fasten the wheel stud bolts. Important note Warning If one or more wheels need to be replaced, proceed as follows: The spare wheel must only be used for short trips in the event • replace the wheel stud bolts with damaged threads or tapers of an emergency. • carefully clean the wheel stud bolts before fitting When the spare wheel is fitted, never exceed the maximum • do not lubricate the contact surfaces between the stud bolt speed of 80 Km/h (50 mph) and drive carefully, especially and the wheel rim and between the wheel rim and the brake around bends and when overtaking, avoiding sudden disk. accelerating or braking. In order not to remove the antilock coating, do not clean the Do not exceed the approved weight limits. wheel rim cones with solvents or aggressive products. Do not fit snow chains on the spare wheel. Never fit more than one spare wheel at a time. Collapsible spare wheel On request, the vehicle comes with a kit containing: • collapsible spare wheel A with space-saving tyre; the label B Important note indicates the maximum speed allowed of 80 km/h Failure to comply with these instructions could lead to loss of control of the vehicle and consequently damage to the vehicle and injuries to its occupants. � � � · Advice for Emergency Situations · 5 • 199

Replacing a wheel • Lift the vehicle carefully using the jack G until the wheel is raised • Position the vehicle on an even surface, then block the rear wheels off the ground. by applying the parking brake. Warning Warning If the jack is not positioned correctly, the vehicle could slip off. Make sure that the vehicle is in a safe position. No part of the body must ever be under the vehicle. The supplied jack must only be used for replacing wheels. • If necessary, switch on the hazard warning lights and place the hazard triangle at the required distance from the vehicle. • Unscrew the five stud bolts and remove the wheel. • Take the spare wheel and tools out of the luggage compartment. • Fit the uninflated collapsible spare wheel. • Loosen the five wheel stud bolts approximately one turn each • Screw the stud bolts into place but do not tighten them. using the wrench D provided. • Place the base of the jack E on flat firm ground under one of the Warning jacking points F on the underfloor as shown in the figure. Inflate the collapsible spare wheel before lowering the vehicle to avoid damaging the rims. • Inflate the collapsible spare wheel using the inflation kit. � � � 5 • 200 · Advice for Emergency Situations ·

Warning Warning The kit must be used in “tyre inflation” mode. Refer to the The spare wheel does not have a tyre pressure monitoring instruction manual supplied with the kit. sensor (see label on spare wheel tool bag). After fitting, it is not checked by the system but conforms to the international • Inflate to the indicated pressure (see page 28). regulations ECE R64/01. • Lower the vehicle and remove the jack. After fitting, we recommend going to the nearest Ferrari Service Network. • Tightly fasten the stud bolts, alternately going from one stud bolt to one that is diametrically opposite. As soon as possible, secure the stud bolts with the torque wrench and tighten them to a torque of 100 Nm. · Advice for Emergency Situations · 5 • 201

Towing Warning When towing the vehicle, avoid using anchor points that are not those for the tow hook A inserted in housing B. While towing the vehicle, you must comply with Road • Take the tow hook A out of the tool bag. Regulations. • Tightly screw the tow hook into housing B. • Release the EPB. Warning • Release the Park Lock. Do not tow the vehicle by attaching it to levers, suspension and wheel rims but only to the tow hook properly fitted in its Warning housing. If there is an electrical system failure, release the EPB and Park Keep the key into position II to enable the lights to work and Lock manually. prevent the steering wheel locking in the event of steering; when towing the vehicle, do not start the engine. Important note Remember that when the engine is switched off, the power steering and brake servo functions do not work. � � 5 • 202 · Advice for Emergency Situations ·

Fuel inertia switch Battery quick release This is a safety switch A in the passenger compartment on the floor It is on the left side of the battery and can be accessed by opening in front of the driver seat that deactivates the petrol pump relays if the engine compartment lid. a collision occurs. Use locking lever B to loosen the clamp. A symbol on the TFT display and the hazard warning lights light Separate the clamp from the battery to disconnect the battery and up to indicate that the switch has been activated. the electrical system. When activated, the doors are also unlocked (if locked) and the central dome light comes on. Warning Warning The battery master switch must only be used if the battery conditioner cannot be connected. The system can be reactivated by pressing the button on the top of the switch. Warning Place the clamp so that it does not come into contact with the battery pole or other metal parts of the vehicle. � � · Advice for Emergency Situations · 5 • 203

Disconnecting the battery Reconnecting the battery Before disconnecting the battery, deactivate the electronic alarm Place the clamp on the battery and fasten it by closing the locking using the remote control. lever. Each time the battery is reconnected, before starting the engine, do Warning the following: - close both doors and close the luggage compartment lid; unlock Never disconnect the battery from the electrical system when and lock the doors using the remote control; open the luggage the engine is running. compartment lid using the remote control. Before disconnecting the battery, lower the side windows by at - adjust the clock (date and time on instrument panel); least 2-3 centimetres to avoid damaging the strips when opening and closing the doors. - Close both doors and fully raise the driver side and passenger side windows to their upper limit; check that the windows move down into the “target position” when the doors are opened. Warning When the battery is connected and charged, this operation is Warning automatically performed when the doors are opened and closed. WAIT at least 1 minute before inserting the key in the ignition The windows must remain lowered until the charged battery switch. is reconnected. If the battery is discharged with the windows Before starting the engine, wait at least 60 second with the completely raised, only open the door if necessary and use the ignition key in position II to allow the electronic system that utmost caution; do not close the door again until the windows controls the motor-driven valves and the A.C. ECU to run a self- can be lowered. learning process. During this period, no devices must be activated. Important note We recommend using the battery conditioner if the vehicle will The self-learning process for the Motronic ECUs works properly not be used for a long period. when the intake air temperature is above 5 °C. 5 • 204 · Advice for Emergency Situations ·

After removing the battery from the vehicle or disconnecting from Battery conditioner the electrical system using the battery master switch, it is important to check that the external temperature is within the indicated values The vehicle is equipped with a battery conditioner to maintain and when reconnecting before effecting the self-learning process. recharge the battery. Checking the battery The battery is placed in the centre of the engine compartment. Important note The vehicle is equipped with a sealed lead acid battery that does Using the battery conditioner will extend the life of the battery. not require maintenance. The device is kept in a pocket inside the car cover bag provided Warning with the vehicle. The battery conditioner connection socket is located on the right of The battery does not need topping up with distilled water or the luggage compartment behind cover B. sulphuric acid. To access socket D rotate the fastener C and open the flap B. • Periodically check that the terminals and pins are clean and firmly secured. Warning • Visually inspect the outer casing for any cracks. Place the battery conditioner where is can be easily seen away • If the battery overcharges, it will wear out quickly. Have the from heat sources and out of children's reach. vehicle electrical system checked if the battery tends to discharge easily. Warning Do not place the battery near sources of heat, sparks or naked flames. D � � · Advice for Emergency Situations · 5 • 205

After connecting the battery conditioner to the socket in the Exhaust system overheating alarm devices vehicle, run the connection cable underneath the luggage compartment lid in the outer/rear corner. If the engine malfunctions with consequent high temperature in the exhaust system, a symbol will appear on the TFT display accompanied by a message. The message varies according to the Important note three alarm levels: high temperature, excessive temperature or Do not run the connection cable out of the vehicle in positions catalytic converter temperature system failure. other than those indicated to prevent damaging the seals and/or Display of the symbol is controlled by the thermistor via the engine the cable. control ECU. If the car is not to be used for periods longer than one week, we Warning recommend that you connect the maintainer in order to keep the Incorrect use of the vehicle may cause the SLOW DOWN battery in good working order. warning light to come on. Warning The engine cannot be started as long as the battery conditioner Warning is connected to the vehicle socket. If the temperature is high: slow down immediately so that the exhaust system temperature drops. Important note Additional technical information on the use of the device can be found in the manual provided inside the pocket of the car cover bag. 5 • 206 · Advice for Emergency Situations ·

Engine malfunction alarm devices Warning If the “Engine diagnostic system failure” (EOBD) warning light If the temperature is excessive: flashes or illuminates permanently while the engine is running, it the temperature in the catalytic converters has reached a indicates that the engine or the emission control system may be dangerous level and could damage them; if you continue to malfunctioning. drive, the engine control ECU intervenes and reduces the The electronic system detects and isolates the error preventing torque produced by the engine. damage to the engine or the production of harmful emissions. The torque limit remains until the catalytic converter temperature drops to normal operating values. Warning When the “engine diagnostic system failure” warning light Warning comes on, engine performance may be considerably reduced. Drive carefully, avoiding sudden acceleration and high speeds. If catalytic converter temperature system failure information is displayed: Contact the Ferrari Service Network immediately. - the engine control ECU intervenes and reduces the torque produced by the engine - the driver must slow down and slowly drive to the nearest Ferrari Service Network to have the engine parameters checked. Warning If the EOBD warning light comes on at the same time as the SLOW DOWN warning light, go the nearest Ferrari Service Network to have the ECU error memory checked. Warning Ferrari is not liable for any damage to property or personal injury arising from failure to comply with the warnings stated above. · Advice for Emergency Situations · 5 • 207

Replacing brake pads and discs Manual closing of retractable hard top Brake pads The front brake pads have a wear detector connected to the brake Warning warning light; if this warning light comes on or braking is not For manual closing of the retractable hard top, two people are even, have the pad thickness and the state of the braking surfaces required. checked. The movements must be slow and synchronised. The minimum brake pad thickness is 3 mm (thickness of the friction material only). If the retractable hard top cannot be moved electronically, it can be Replacing brake pads closed and moved manually. To perform the operations described When the brake failure warning light comes on, it means that below, two people are required. the front brake pads are excessively worn and must be replaced • Completely lower the side windows. immediately. • Open the luggage compartment lid. Warning • Disconnect the battery by detaching the quick release. • Lift up the luggage compartment lid. To guarantee the quality of the components and perfect installation, we recommend having brake pads replaced at a • Open the left A and right B sections of the luggage compartment Ferrari Service Centre. by turning the relative fasteners C. After replacement, avoid sudden braking until the new pads are seated properly (approximately 300 km). � � � � 5 • 208 · Advice for Emergency Situations ·

• Locate the Tonneau Cover latch D in the left section. • Lower the luggage compartment lid. • Locate the Tonneau Cover latch E in the right section. • Insert the special key in the tool kit supplied with the vehicle in Warning the Tonneau Cover housing. DO NOT close the luggage compartment completely. • Turn the key clockwise to release the left Tonneau Cover latch and turn the key counterclockwise to release the right Tonneau Cover latch. Warning Make sure that flaps F and G shown in the figure have opened correctly. If they are not fully open, DO NOT effect the emergency manoeuvre to avoid causing possible damage. � � � � · Advice for Emergency Situations · 5 • 209

• Lift up the Tonneau Cover until it is completely open. • Hold the front - rear roof package stored in the luggage compartment and get ready to lift it. Important note Important note Two people are required to open and close the retractable hard top using slow, synchronised movements. To do this, hold the package with both hands working on both Use the holds as shown in the figure by the arrows. sides of the vehicle. 5 • 210 · Advice for Emergency Situations ·

• Lift the front-rear roof package right up and let it drop down until • Lift up the luggage compartment. it touches the windscreen pillars. • Lock the Tonneau Cover latch. • Lower the Tonneau Cover and let it drop until it has gone into its • Insert the key in housing D on the left of the luggage housing. compartment and turn counterclockwise. • Insert the key in housing E on the right of the luggage compartment and turn clockwise. � � · Advice for Emergency Situations · 5 • 211

• Close the rear roof by holding it with both hands and working on both sides of the vehicle and let it drop down until it goes into its Warning housing. Make sure that has locked and if not, repeat the procedure. Warning • Reposition the fabric on both sides. To do this, hold the rear roof with both hands and work on • Close the left section with fabric A. both sides of the vehicle. • Close the right section with fabric B. • Fasten both covers by turning the fasteners C. • Move the roof internal covering fabric H until you find the rear roof latch I. • Close the luggage compartment lid. • Release the rear roof latch by turning the special key clockwise; do this in the left lock and then the right one by turning the key very carefully to avoid damaging the cover. � � � � � � 5 • 212 · Advice for Emergency Situations ·

Emergency unlocking of electric parking brake This movement loosens the parking brake cables. Warning Important note When the electric parking brake is deactivated manually, the To release the brake completely, the key needs to be turned vehicle may move unexpectedly! 50 times whereas it starts to be released after approximately 20 turns. To keep the vehicle stationary, the Park Lock safety device must be applied: make sure that the letter “P” appears on the DOT MATRIX display. Once the electric parking brake has been manually released, the EPB node records a failure at the next key-on and a warning light and the following message “Parking Brake system revision. Go to dealer” is If the electric parking brake cannot be deactivated because the displayed on the TFT display. battery is flat or there is a failure in the electrical system that controls it and the vehicle needs to be moved, the emergency procedure described below must be performed. Warning • Open the luggage compartment lid. The parking brake resumes normal operating but it is important • Remove the tool kit cover. to go to the nearest workshop to have it calibrated and delete any • Take key A out of the tool kit to release the electric parking brake. errors in the error memory. • Using the special rectangular groove B in the right of the tool kit Go to a Ferrari Service Centre. (marked by a plate), place the release key in the hole (in the left Calibration is necessary for safety reasons. part of the groove) and turn it clockwise. � � · Advice for Emergency Situations · 5 • 213

Park lock emergency release. Warning Warning If the vehicle is not on a level surface, the Park Lock must be released by the device in the passenger compartment. However, this should be avoided unless absolutely necessary: - to tow the vehicle After releasing the Park lock, the following message may appear on the - if there is a Park Lock failure (the following message is TFT display “Only manual unlock gearbox allowed: See handbook” displayed on the TFT display: “Only manual unlock gearbox Procedure for releasing the Park Lock from the passenger compartment allowed: See handbook”). Warning Warning This procedure must only be performed when the vehicle is on When the Park Lock safety device is deactivated manually, the a level surface. vehicle may move unexpectedly. The vehicle is only kept stationary by the parking brake, if The Park Lock manual release device is in the pocket-change applied. compartment on the centre console. • Take key B out of the tool kit. • Open the pocket-change compartment on the centre console. • Remove the rubber cap A. � � 5 • 214 · Advice for Emergency Situations ·

• Place key B in the device housing in the pocket-change • Place key B in the device housing in the pocket-change compartment. compartment. • Turn the key clockwise. • Turn the key counterclockwise. if the electrical system allows it, check that the letter “N” appears on If the electrical system allows it, check that the letter “P” appears on the Dot Matrix display by turning the ignition key to position “II”. the Dot Matrix display by turning the ignition key to position “II”. The following message “Gearbox not in Parking position” appears • Close the device hole with the rubber cap A. on the TFT display. Warning Important note In the event of emergency unlocking due to a Park Lock failure, Once the vehicle has been moved to a safe place, the Park Lock go to the nearest Ferrari Service Centre to resolve the problem. must be reset. B � · Advice for Emergency Situations · 5 • 215

Procedure for releasing the Park Lock from the luggage compartment • Remove the rubber cap F that protects the device. • Place key B in the device and turn it clockwise. Warning if the electrical system allows it, check that the letter “N” appears on the Dot Matrix display by turning the ignition key to position “II”. Only release the Park Lock in this way if the vehicle is on a level The following message “Gearbox not in Parking position” appears surface. on the TFT display. Warning When the Park Lock device is deactivated manually, the vehicle may move. The vehicle is only kept stationary by the electric parking brake, if applied. The Park Lock manual release device is in the luggage compartment. • Take key B out of the tool kit. • Open the luggage compartment. • Remove the felt cover E. � � B � 5 • 216 · Advice for Emergency Situations ·

If the electrical system allows it, check that the letter “P” appears on Important note the Dot Matrix display by turning the ignition key to position “II”. Once the vehicle has been moved to a safe place, the Park Lock • Close the device with the rubber cap. must be reset. • Close the device hole with the felt. • Close the luggage compartment lid. • Place key B in the device housing in the luggage compartment. • Turn the key clockwise. Warning In the event of emergency unlocking due to a Park Lock failure, go to the nearest Ferrari Service Centre to resolve the problem. B · Advice for Emergency Situations · 5 • 217

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Warranty Booklet Maintenance schedule The vehicle comes equipped with a “Warranty Booklet”. At the intervals prescribed, the Ferrari Service Centres must This contains the vehicle’s warranty validity conditions. perform all the tuning and checking operations indicated in the “Warranty Booklet”. Warning It is however advisable to immediately report any small fault which may occur during use of the vehicle (e.g. small leaks of essential The warranty booklet also contains special blank spaces fluids) to Ferrari Service Centres and not wait until the next where the Authorised Service Centres can register the service is due to correct the problem. regular maintenance services performed, as indicated in the It is required to have the periodic maintenance services performed maintenance schedule. at least once a year, even if the specified mileage limit has not been reached (see “Yearly Maintenance” in the “Warranty Booklet”). Maintenance Chassis and bodywork maintenance It is essential to always keep the vehicle in proper working order The chassis has technological and manufacturing specifications that to ensure a long working life and to prevent any running defects, require that any operation be performed by staff specially trained to caused by negligence or lack of maintenance, and consequently to work with this innovative technology. avoid hazardous situations. It is of crucial importance to use equipment tested by Ferrari if the repair work is to be performed in accordance with rules of Important note good workmanship. Proper execution of repair work ensures that the commercial value of the vehicle is preserved and the safety All repair work on any component of the safety system must be standards are complied with. performed by the Ferrari Service Network. Important note If the chassis is damaged as a result of an accident, Ferrari recommends that you contact the Ferrari Service Network. 6 • 220 · Care of the vehicle ·

The chassis, under standard conditions of use, requires no Engine oil maintenance; it is however advisable to contact the Ferrari Service Network at the intervals indicated in the “Warranty Booklet” in Warning order to have it checked. The engine oil level must be checked when the engine is warm. Level checks Warning Important note The engine oil level must be checked when the vehicle is on level The level checks must be performed at the intervals indicated ground. in the “Warranty Booklet” or, in any case, before starting a long journey. The message “checking engine oil level” displayed next to the following symbol on the TFT display indicates to the driver that the engine oil level must be checked. Environment All the materials used for the following operations (e.g. cloths soaked with oil or grease, pans, etc.) must be disposed of in compliance with the environmental protection regulations. Proceed as follows: Run the engine until the engine oil temperature has reached 80 ÷ 90 °C. Important note A. Open the engine compartment lid. Only use lubricants and/or fluids recommended by Ferrari B. Switch off the engine. (see the “Refilling” table on page 31). Warning The oil must be checked when the ENGINE IS OFF. · Care of the vehicle · 6 • 221

C. Completely remove the dipstick 1 on the left side of the engine. D. Remove the oil top-up cap 2 and wait 5 minutes for the oil to Warning drain back into the oil pan. DO NOT add oil with different characteristics from those of the oil already in the engine. Warning If the oil level is below the “MIN” mark, top it up and then have If the level is close to or under the MIN mark, top up with the the system checked by the Ferrari Service Network. recommended oil. E. Clean the dipstick, insert and remove again and check that the Warning oil level shown on the dipstick 1 is between the MIN and MAX DO NOT fill beyond the MAX level. notches. F. Top up until the oil reaches the MAX level on the dipstick. Important note After the top-up, the “low oil level” warning light on the TFT The distance between the MIN and MAX marks corresponds to display may remain on for some time. This is so the system can approx. 1.5 litres of oil. perform all the necessary checks. 1 2 6 • 222 · Care of the vehicle ·

You should therefore consider this behaviour normal. Coolant G. When you have added or changed the oil, recheck the oil level as indicated above. Warning This procedure must always be performed when the engine is Environment cold. Never remove the cap from the expansion tank when the engine is running or warm. Top up with due care to avoid pouring the oil out of the filler neck. • Remove the cap 3 from the expansion tank in the engine compartment and check that the level is at approximately 40 mm DCT semiautomatic gearbox oil from the top of the filler neck. • If the level is low, top it up with the recommended fluid. Important note We recommend that you have the oil level of the semiautomatic Important note gearbox checked by the Ferrari Service Network or by skilled staff. If frequent top-ups are required after short trips, have the system checked by the Ferrari Service Network. • Screw the cap 3 back on tightly. 3 · Care of the vehicle · 6 • 223

Hydraulic steering system oil Top up if necessary with the recommended oil up to the MAX level. Screw the cap 4 back on tightly. Warning The power steering oil level must be checked with the engine Environment warm, after having driven at least 15 Km. Never dispose of used fluid in the environment. Warning If the oil level is below the “MIN” mark, top it up and then have the system checked by the Ferrari Service Network. The power steering tank is located in the centre of the engine compartment. Remove the cap 4 from the tank in the engine compartment and check that the level is between the MIN and MAX marks on the dipstick. The oil level must be checked with the cap resting on the tank. 4 6 • 224 · Care of the vehicle ·

Brake fluid • Check that the fluid in the tank is near the MAX level. Warning • If the level is low, unscrew the cap 5 and top up with the The oil contained in the brake and clutch systems, in addition to recommended oil taken from a sealed container. damaging plastic, rubber and painted parts, is highly dangerous if it comes into contact with the eyes or the skin. In case of contact, wash the affected part thoroughly with running Environment water. To avoid any risk, always use protective goggles and gloves. Never dispose of used fluid in the environment. Keep out from children's reach! The symbol on the tank cap 5 indicates that the system contains synthetic fluid. Warning The use of mineral-based fluids will irreparably damage the system rubber gaskets. Do not use fluids other than those already contained in the system for topping up. • After topping up, screw the filler cap back on. 5 · Care of the vehicle · 6 • 225

Windscreen wipers and washer fluid Wheels and tyres The tank for the windscreen wipers and washer fluid can be To ensure maximum performance and tyre life and to permit the accessed by lifting the engine compartment lid. best tyre adjustment on the wheel rim, it is important to comply • Lift the cap 6 and fill the tank with the recommended fluid (see with the following instructions for the first 200-300 km (125– the “Refilling” table on page 31) until it can be seen in the filling 185 mi.) with new tyres: manifold. • avoid sudden acceleration • Close the cap 6. • avoid sharp braking and steering • drive at moderate speed on straight roads and on curves. How to use the tyres Important note To ensure safe driving, the tyres must be kept in good condition. The inflation pressure must correspond to the specified values and must be checked only when the tyres are cold: tyre pressure increases as tyre temperature increases. Never reduce the pressure if the tyres are hot. Environment 6 Periodically check the tyres pressure. Insufficient tyre pressure can lead to overheating, damage and even destruction of the tyres. 6 • 226 · Care of the vehicle ·

Warning Important note Inflating the tyres to a pressure which is different from that The Ferrari Service Network can certify whether aged tyres prescribed will render the monitoring system inaccurate. are suitable for use. In any case, tyres that have remained on a vehicle for more than 3 years must be checked by a Ferrari Sudden impact against sidewalks, holes in the road and other Service Centre. obstacles of various types, as well as long trips on rough roads, can cause damage to the tyres that is not always visible to the naked eye. Warning Check the tyres regularly for any signs of damage (e.g. scratches, cuts, cracks, bulges, etc.). We recommend that you replace the tyres every 4 years in case If sharp objects penetrate the tyres, they can cause damage which is of normal use. Frequent use in maximum load conditions and at only visible when the tyre is removed. high temperatures may accelerate ageing. Have any damage inspected by an expert as it may considerably reduce tyre life. Never fit tyres of uncertain origin. Remember that tyres deteriorate over time, even if they are rarely used or not used at all. Warning Cracks in the tread and side walls, possibly accompanied by bulging, The tyres are of the “directional” type and there is an arrow are sure signs of ageing. marked on their side wall to indicate the direction in which they must rotate or which side is the outer side. In the case of Important note replacement, maximum performance levels can only be ensured if the rotation direction corresponds with the direction indicated The Ferrari Service Network has the necessary equipment for by the arrow. tyre replacement. Tyres on the same axle must always be replaced in pairs. Have the tyres replaced by the Ferrari Service Network who has the equipment needed to avoid damage to the sensor inside the wheel rim which could be caused by carelessly performed Regularly check the tyre tread (minimum acceptable depth procedures. 1.7 mm). As the tread wear increases, there is a greater risk of skidding. Ensure that the tyres on stock are not older than 4 years. The maximum life of the tyres kept in stock is of 4 years, provided that they are stored in a place protected from the sun, weather agents and damp, and where there is a low oxygen content. · Care of the vehicle · 6 • 227

Cleaning the vehicle Warning Drive carefully on wet roads to reduce the risk of “aquaplaning”. Cleaning the exterior Wheel alignment check and adjustment Environment When you notice unusual wear of the tyres and in any case, at the intervals prescribed in the “Warranty Booklet”, have the Ferrari All the materials used for the following operations (e.g. cloths Service Network check the wheel toe-in and camber. soaked with oil or grease, pans, etc.) must be disposed of in compliance with the environmental protection regulations. Maintenance of the seat belts and pretensioners • Periodically check that the screws on the anchoring points are Proper care of the vehicle on the part of the owner is essential for tight and that the belt is in perfect condition and slides smoothly. the vehicle long life. • The belt must be kept clean; the presence of any dirt could Below is a list of the main precautions to be taken. jeopardise the efficiency of the belt winder. • Certain parts of the vehicle should not be left wet or dirty for • To clean the seat belt, wash it by hand with mild soap and water, long periods of time: in particular, the passenger compartment rinse it and let it dry. Do not use strong detergents, bleach or floor and the luggage compartment must always be kept clean aggressive solvents, as they can weaken the fibres. and dry. The draining holes under the doors should be kept unclogged to allow any water to drain. • Do not let the belt retractors get wet: proper functioning is ensured only if they are kept dry. • The underbody and the lower surfaces of the vehicle should be cleaned regularly, and more frequently (at least once a week) if • The pretensioner requires no maintenance or lubrication. If the vehicle is used on salty or rough roads. The vehicle should immersed in water or mud, the pretensioner must necessarily be be cleaned thoroughly and carefully: cleaning that merely replaced. wets encrusted mud without removing it completely can prove • The pretensioner must be replaced at the intervals indicated in damaging. the “Warranty Booklet”. • The vehicle must be washed regularly with suitable equipment. Do not use very hot water or steam to clean the paintwork and the lower surfaces. It is advisable to soften any dirt first, then remove it with a jet of water at room temperature. 6 • 228 · Care of the vehicle ·

Cleaning of the Antistone Film (optional) Warning The film has been studied for the protection of the bodywork, all Do not use aggressive products for cleaning the windows. that may damage the paint will also damage the film. The use of aggressive products could seriously damage the bodywork. Warning Do not pour denatured ethyl alcohol, acetone, isopropyl alcohol, • Do not wash the vehicle in direct sunlight or when the bodywork heptane or substances that contain these compounds on the is still warm: ensure that the jet of water does not strike against film. the paintwork too hard. Wash the vehicle with a sponge and a solution of mild soap and water. Rinse the vehicle again with a jet of water and dry it with a piece of chamois leather. • Do not apply adhesive elements on the film. • When cleaning, do not use metal or abrasive substances in general Important note and acid chemical compounds. When the vehicle has been washed, apply slight pressure to the brake pedal at moderate speed before driving at a normal speed, Important note until the brake discs and pads have cleaned off. Avoid contact with the brake fluid as the film will become opaque. In order to maintain the shine of the paintwork, polish it once or twice a year with the products recommended by Ferrari. • Do not use solvents along the edges of the film to them from • Any areas that are cracked or chipped as a result of stones, penetrating inside the adhesive layer. scratches or parking manoeuvres, etc., must be immediately repaired by the Ferrari Service Network. Important note • Do not park the vehicle in damp and/or unventilated areas for long periods of time. Avus White, Alloy Grey, Nürburgring Silver vehicles must be washed every month and waxed at least twice a year so that dirt, acid rain, pollutants, etc. do not penetrate the pores of the film causing it to tarnish. · Care of the vehicle · 6 • 229

natural material. Important note Cleaning the interior - Cleaning and care of the We recommend that the film be replaced every 24 months for Avus White, Alloy Grey, Nürburgring Silver vehicles, which may Alcantara® upholstery show a light visible tarnish due to dirt inside the pores of the film. Warning It is to be understood that a timely and accurate cleaning (monthly Do not use equipment with steam for cleaning! washing and wax twice a year at least) will prevent deterioration. • Carefully dust the parts to be cleaned Cleaning and care of the leather upholstery • Use a soft cloth or sponge moistened with clean water As indicated in the “MAINTENANCE SCHEDULE” (see “Warranty • Squeeze out all the water and treat the entire Alcantara® area Booklet”), proper and regular treatment, at least once a year, will being careful not to get it wet in depth. help preserve the quality, natural characteristics and softness of the • Repeat this procedure a second time leather upholstery in your Ferrari. • Let it dry completely With this in mind, specific leather care products are also available (“Cleaner” and “Cream”) both tested by Ferrari. • To recondition the material, gently use a brush with soft bristles. These products can be ordered through the Ferrari Spare Parts Service Department, both individually and as part of the “Care Kit” which includes the complete range of products for cleaning the vehicle. Important note For use of the “Care Kit” products, contact the Ferrari Service Network. The following products must be avoided when cleaning the leather: harsh detergents, turpentine, liquid stain removers, petrol, solvents and domestic cleaning products. All of these products damage the 6 • 230 · Care of the vehicle ·

If the vehicle is stored for long periods If the vehicle is not used for long periods of time, certain precautions should be taken: • if possible, park the vehicle on a level surface in a covered and well-ventilated area • prevent the vehicle from moving by putting it into gear • bring the tyre pressure to 3.0 bar and periodically change the point where the tyres rest on the ground • connect the battery conditioner Important note If you do not wish to connect the battery to the battery conditioner, in order to keep certain devices functioning such as: radio station memory, alarm system, etc., the battery must be recharged at least once a month. If the vehicle is not used for long periods of time without connecting the battery conditioner, the battery must be recharged at least every three months. • protect the vehicle with a breathable fabric cover, avoiding materials that would prevent any dampness on the bodywork from evaporating. Before using the vehicle again after long periods of inactivity, adjust the tyre pressure to the indicated pressure and check the fluid levels of all the systems. · Care of the vehicle · 6 • 231

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

7 • 234 · Glossary ·

Abbreviation Meaning ABS (Anti Blockier System) The ABS prevents wheel blocking when braking so that vehicle steerability can be maintained. A.C. Air-conditioning ASR (Antriebs Schlupf Regelung) Anti-skid regulation during acceleration. Autohold Automatic activation of the electric parking brake (EPB) when the engine is switched off. This function can be disabled Auto easy exit Automatic gearbox with limited operating. To exit the “Auto easy exit” mode, simply operate one of the two shift paddles. AVH Automatic Vehicle Hold Additional function of the electric parking brake (EPB): it allows the gradual release of brake shoes/pads when the vehicle starts up. This guarantees an optimised release for the vehicle to help the driver. CST Stability and Traction Control. Consisting of two systems: VDC and F1-Trac DCT Dual Clutch Transmission: each clutch is assigned a part of the gearbox, one designed for engaging even gears, the other for odd gears. Once a gear has been engaged, the system has already preselected the next one. Once the correct number of revs has been reached, a clutch opens whereas at the same time the other one closes so that the traction force is not interrupted. EBD (Electronic Brake-Force Distribution) Electronically-controlled brake-force distribution ECU Electronic Control Unit EPB Electric Parking Brake: the system operates by way of an ECU and an electric motor on the brake shoes of the rear brakes. F1-Trac Traction control derived from the technologies used in the racing sector. The system can estimate the maximum available grip in advance by continuously monitoring the relative wheel speed and using an auto-adaptive operation logic. Comparing this information with the vehicle dynamics model stored in the control system, F1-Trac, optimises the vehicle behaviour by controlling engine torque delivery. · Glossary · 7 • 235

Abbreviation Meaning Launch Strategy for performance standing start. Manettino The driving mode control switch is a quick, intuitive way to make the most of vehicle potential. Park Lock Automatic DCT gearbox park lock. When the engine is off, a mechanical lock is automatically activated to prevent the vehicle from moving if the electric parking brake is not activated. RHT Retractable Hard Top TFT display Multifunction display on the instrument panel that displays information on the control system. TPMS Tyre Pressure Monitoring System. Using special sensors fixed inside the wheel rims next to the air valve, the measured data is sent to an ECU. The data and messages are displayed on the TFT display. Tractability Force exerted by the vehicle on the road surface through the wheels; it expresses grip. VDC Vehicle Dynamic Control performed through the braking system and engine torque. Xenon headlights Headlights on the front of the vehicle that produce a more intense beam by using an electric arc rather than an incandescent spiral. 7 • 236 · Glossary ·

1. General 2. Quick reference guide 3. Safety 4. About your vehicle 5. Advice for Emergency Situations 6. Care of the vehicle 7. Glossary 8. Table of Contents

Index B Backrest and cushion side width adjustment .................. 168 Battery ............................................................................................... 205 Battery conditioner ...................................................................... 205 A Battery quick release ................................................................... 203 Before a trip .......................................................................... 153, 154 “Adaptive Light Control” function display ........................ 130 Before you drive ........................................................................... 160 “Automatic Vehicle Holding” AVH system display ........ 133 Body Computer fuses and relays .......................................... 194 “Auto easy exit” gearbox ........................................................... 159 Brake fluid ....................................................................................... 225 Abbreviations ...................................................................................... 9 ABS .......................................................................................................84 C Activation of electronic alarm ....................................................17 Active safety .......................................................................................59 Carwash ............................................................................................ 165 Adaptive light system.................................................................. 121 Chassis and bodywork maintenance ................................... 220 Adjusting the air vents ............................................................... 175 Child restraint systems that can be installed Adjusting the steering wheel................................................... 170 with 3-point seat belts - 2-seater version..............................98 Airbags .................................................................................................72 Child restraint systems that can be installed Airbag system - Components .....................................................72 with 3-point seat belts - 2 + 2-seater version .....................98 Air conditioning and heating system ................................... 172 Child restraint systems that can be installed Air conditioning and heating system controls ................. 173 with ISOFIX - 2 + 2-seater version ........................................99 Alarm memory ..................................................................................19 Child safety ........................................................................................66 Alarm system .....................................................................................15 Child safety - 2-seater version ................................................... 67 Ashtray .............................................................................................. 176 Child safety - 2 + 2-seater version ..........................................69 Ashtray/cigarette lighter ......................................................... 176 Cleaning and care of the Alcantara upholstery ............... 230 Automatic gearbox....................................................................... 159 Cleaning and care of the leather upholstery .......... 229, 230 Cleaning the exterior .................................................................. 228 Cleaning the parking sensors .................................................. 137 Cleaning the vehicle.................................................................... 228 8 • 240 · Table of Contents ·

Clock.................................................................................................. 123 DISP (DISPLAY) button .......................................................... 125 Closing the engine compartment lid ................................... 103 Dome light....................................................................................... 121 Closing the luggage compartment lid ................................. 104 Doors ....................................................................................................34 Collapsible spare wheel ............................................................. 199 DOWN .............................................................................................. 158 COMFORT mode .........................................................................147 DOWN-shifting ................................................................................52 Consulting the manual.................................................................... 8 Driver-side power window ....................................................... 106 Consumption ..................................................................................... 27 Driver and passenger airbags ..................................................... 74 Controls overview ........................................................................... 37 Driver seat Easy Entry/Exit ..................................................... 170 Coolant ............................................................................................. 223 Driving .................................................................................................45 Cruise control ................................................................................ 150 Driving at night ............................................................................. 161 CST .......................................................................................................85 Driving in fog ................................................................................. 162 CST-OFF mode ..............................................................................147 Driving in the rain ....................................................................... 161 Driving on mountain roads ...................................................... 163 D Driving on snowy or icy roads ............................................... 163 Driving style ......................................................................................10 “Doors/Engine or luggage compartment lid open” Driving the vehicle....................................................................... 152 function display............................................................................. 131 Driving using the driving mode control switch “DOWN” shift paddle................................................................. 148 (“Manettino”)................................................................................. 164 Date and hour ................................................................................ 123 Driving with the “ABS” braking system ............................. 163 DCT semiautomatic gearbox oil ............................................ 223 Duplicating the keys.......................................................................16 Deactivating the anti-lift alarm ..................................................18 Deactivation of electronic alarm ...............................................18 Deformable body ............................................................................59 Dimensions and weights ..............................................................26 Dimming of lights ........................................................................ 134 Direction indicators .................................................... 47, 119, 120 Disallowed roof operations ...................................................... 113 · Table of Contents · 8 • 241

E F Electrical system .............................................................................. 27 F1-Trac .................................................................................................85 Electronic alarm ...............................................................................17 Ferrari CODE system.....................................................................15 Electronic parking brake ........................................................... 167 Flaps communicating with luggage compartment ..........177 Electronic speedometer ............................................................. 109 Flashing the headlights.......................................................46, 117 Emergency opening - Engine compartment lid .............. 103 Fuel inertia switch ...........................................................................83 Emergency opening - Fuel filler flap ................................... 105 Fuel level gauge ............................................................................ 129 Emergency opening of engine compartment lid ............ 103 Fuel tank cap and flap ................................................................ 104 Emergency opening of fuel filler flap .................................. 105 Fuse .................................................................................................... 190 Emergency tyre repair and inflation kit ............................. 185 Fuses and relays in the engine compartment ................. 193 Emergency unlocking of electric parking brake ............. 213 Fuses and relays on centre console ...................................... 198 Emissions ............................................................................................ 27 End-of-life vehicle collection service ......................................11 G Engine compartment lid............................................................ 103 Engine malfunction alarm devices ........................................ 207 General remarks ................................................................................ 4 Engine oil ........................................................................................ 221 Global Closed ................................................................................ 107 Engine oil temperature gauge ............................................... 126 Global Open ................................................................................... 107 Environmental protection ............................................................10 Glossary ............................................................................................ 234 EPB .............................................................................................86, 167 Glove compartment .................................................................... 176 Exhaust system overheating alarm devices ....................... 206 External lights and direction indicators ................................46 External lights failure display ................................................. 133 External rear-view mirrors ....................................................... 171 8 • 242 · Table of Contents ·

H L Hazard warning lights ................................................................... 47 Launch .............................................................................................. 166 Headlight bulbs ............................................................................ 188 Level checks ................................................................................... 221 Headlight washer ............................................................... 149, 151 Lighting ............................................................................................ 117 Headrest adjustment................................................................... 170 Light bulbs...................................................................................... 191 Head Airbags .................................................................................... 78 Light switch .................................................................................... 117 High beams..............................................................................46, 117 Locking and opening the doors from the inside............ 102 Horn control................................................................................... 148 Low tyre pressure ...........................................................................88 How to fasten seat belts ...............................................................62 Luggage compartment lid ........................................................ 104 Hydraulic steering system oil .................................................. 224 Lumbar support adjustment .................................................... 168 I M Identification and homologation plates and labels ..........20 Maintenance ................................................................................... 220 If the vehicle is stored for long periods ............................. 231 Maintenance of seat belts and pretensioners ......................65 Ignition switch ........................................................................45, 165 Maintenance of the seat belts and pretensioners ........... 228 Instruments and gauges ............................................................ 108 Maintenance schedule ................................................................ 220 Instrument panel warning lights ........................................... 139 Main engine specifications .......................................................... 27 Internal electrochromic mirror............................................... 171 Manettino............................................................................... 146, 147 Manual closing of retractable hard top ............................... 208 K MENU............................................................................................... 128 Menu Page ....................................................................................... 123 Key codes ...........................................................................................14 Ministerial homologation .............................................................19 Key lock ........................................................................................... 166 MODE button ................................................................................ 125 KEY ON ........................................................................................... 124 · Table of Contents · 8 • 243

N Pocket-change compartments.................................................. 176 Position II - Ignition ................................................................... 166 “N” (Neutral) request ....................................................................52 Power windows ............................................................................. 106 Number plate light bulb ........................................................... 189 Pretensioners .....................................................................................64 N - Neutral ...................................................................................... 158 Push start ......................................................................................... 159 O R Opening doors..................................................................................34 Rain sensor failure ....................................................................... 152 Opening doors from the outside ........................................... 102 Rear-view mirrors .................................................................42, 171 Opening the engine compartment lid ................................. 103 Rear fog lights .........................................................................47, 120 Opening the fuel tank cap flap ............................................... 104 Rear power windows .................................................................. 107 Opening the luggage compartment lid ............................... 104 Rear seat belts ..................................................................................63 Operation with the engine off ...................................................49 Refilling .....................................................................................31, 153 Other light bulbs .......................................................................... 189 Replacing a fuse ............................................................................ 190 Replacing a wheel ........................................................................ 199 P Replacing other light bulbs .................................................... 189 Parking lights ................................................................................. 118 Replacing remote control batteries .........................................17 Parking sensors ............................................................................. 134 Replacing the brake pads and brake discs ....................... 208 Park Lock ......................................................................................... 165 Replacing the headlight bulbs ................................................ 188 Park lock emergency release. .................................................. 214 Replacing the number plate light bulb............................... 189 Passenger-side power window................................................ 106 Replacing the supplementary taillight bulbs .................... 188 Passenger compartment accessories ..................................... 176 Replacing the taillight bulbs ................................................... 188 Passenger side fuses and relays.............................................. 196 Retractable hard top ............................................................35, 110 Passive safety .....................................................................................58 Roll bar ................................................................................................81 Performance ....................................................................................... 27 Roof closing using switch ......................................................... 112 Placing suitcases in the luggage compartment .................177 Roof in stand-by operations .................................................... 113 Pocket-change compartment ................................................... 176 Roof opening using switch....................................................... 111 Roof panel controls .................................................................... 146 8 • 244 · Table of Contents ·

Running-in ...................................................................................... 152 Suitcases in the luggage compartment.................................177 Run Flat tyres....................................................................................30 Summary of TPMS displays .......................................................95 Sun radiation sensor ................................................................... 176 S Sun visors ........................................................................................177 Supplementary taillight bulbs................................................. 188 “Speed limit” function display ................................................ 131 Switching off the engine ........................................................... 158 Safe driving ..................................................................................... 160 Satellite Alarm System ..................................................................19 Seats ......................................................................................................40 T Seat adjustment......................................................................40, 167 “TFT” display ................................................................................. 122 Seat back rake adjustment ....................................................... 168 “Tyre pressure and temperature” display........................... 132 Seat belts - Safety............................................................................60 Taillight bulbs ................................................................................ 188 Seat belts - Unfastening ...............................................................63 TFT display warning light display priority levels..............86 Seat belts - use .................................................................................43 TFT display buttons .................................................................. 122 Seat heating system .................................................................... 170 TFT display warning lights ...................................................... 139 Seat position memory................................................................. 168 Tilting the backrest...................................................................... 169 Semi-automatic gearbox display (F1) ................................. 144 Toolkit ............................................................................................... 184 Service .................................................................................................... 7 Tool bag............................................................................................ 184 Spare parts ........................................................................................... 7 Towing hook ................................................................................... 202 Special Ferrari child restraint systems ....................................99 TPMS inactive ..................................................................................94 Special warnings ..............................................................................56 TPMS not calibrated......................................................................92 SPORT .............................................................................................. 126 TPMS temporarily inactive .........................................................94 SPORT mode ..................................................................................147 Transmission ratios ......................................................................... 27 Starting and driving the vehicle ...............................................48 TRIP A/B ........................................................................................ 127 Starting and driving the vehicle (DCT gearbox) ........... 154 Turning off the engine and deactivating the system........52 Starting the engine .........................................................................50 Twilight sensor .............................................................................. 119 Starting the vehicle.........................................................................51 TYRES .............................................................................................. 127 Start button..................................................................................... 146 Tyres ......................................................................................................28 Stopping the vehicle ......................................................................52 Tyre pressure and temperature monitoring system .......... 87 · Table of Contents · 8 • 245

Tyre pressure monitoring system failure ...............................93 W Tyre puncture ....................................................................................89 “Warning: danger of ice” display ........................................... 130 Warming up the engine ................................................................51 U Warning of faulty roof opening and closing ..................... 116 “UP” shift paddle ......................................................................... 148 Warranty Booklet ......................................................................7, 220 UP ....................................................................................................... 157 Wheels and tyres - Use .............................................................. 226 UP-shifting ...............................................................................52, 157 Wheel alignment check and adjustment ............................ 228 UP-shifting due to overrevving .............................................. 157 Wheel rims .........................................................................................28 Updating ............................................................................................... 7 While travelling ............................................................................. 160 UP / DOWN button.................................................................... 125 Windscreen and headlight washer/wipers ........................ 149 Use of the vehicle ............................................................................10 Windscreen washer ..................................................................... 149 Windscreen wipers and washer fluid .................................. 226 V Wind deflector ............................................................................... 180 VDC ......................................................................................................85 Vehicle keys .......................................................................................14 8 • 246 · Table of Contents ·

Equipment and options in Ferrari vehicle models may vary because of specific legal and market requirements. The information contained in this publication is therefore not binding in any way. Ferrari reserves the right to make any modification to the vehicle models described in this manual, at any time, for either technical or commercial reasons. Contact the nearest Ferrari Dealer for any further informa- tion you may require. In the interests of efficiency and safety, as well as to preserve the value of the vehicle, we do not recommend modifying the equipment using non-approved parts.

Code n° 82110300 Catalogue n° 3384/08 EDITION 1st edition February 2009 EDITING STAR s.r.l. Alessandria - Italia PRINTING STAR s.r.l. Alessandria - Italia COPYRIGHT© Technical Service Department Via Abetone Inferiore, 4 41053 Maranello Modena - Italia