Ferrari 458 Spider Owners Manual

Thursday, August 31, 2017
Download

Owner's manual

General remarks - Caution and discipline are the basis of safe driving. - Driving takes place in a naturally dangerous context where a This vehicle, which complies with EC homologation parameters, number of different risk factors interact. For this reason, it is uses advanced technology and is capable of achieving high important to drive bearing in mind that others, whether they performance levels. are pedestrians, motorcyclists or motorists, can make mistakes. Keeping a safe distance allows emergency measures to be It is equipped with sophisticated active and passive safety taken. Remember that national and international legislation systems (described below). requires that the driver of the vehicle must be capable of These safety features and systems do not authorise the driver performing corrective and/or emergency manoeuvres at all to take risks other than those involved in normal driving since times. their preventive and protective action is guaranteed only in - Correct and careful use of a vehicle derives, above all, from certain conditions. Unless otherwise instructed specifically by respect for one's own safety and that of others as well as Ferrari (see the Safety chapter), the deactivation of any of the from compliance with road regulations. Only this respect will vehicle’s safety systems is PROHIBITED. help you experience all the emotions that driving this car can offer you. While certain safety systems (e.g. the airbags) have been tested to ensure that they offer the highest possible levels of protection, they may nonetheless be hazardous in the event of The driver MUST NEVER allow passengers to increase the failure by the driver or passenger to observe the instructions risks associated with driving (e.g. by not using safety systems given by Ferrari. All vehicle occupants must be attentive at such as the seat belts) by failing to observe the mandatory all times and take particular care when transporting passengers safety rules that apply to both driver and passengers. who are more subject to injury such as children, disabled and The vehicle MUST NOT be modified or tampered with for elderly persons. any reason whatsoever since, by so doing, the manufacturer's Safe driving is subject to the following conditions AT ALL TIMES: homologation and safety parameters will be modified. - the driver must be in perfect psycho-physical condition; - road regulations (Traffic Regulations - Vienna Convention on Road Traffic that ended on 8 November 1968) must be strictly observed; - common rules of caution must always be observed in relation to the quality/performance of the vehicle, driving conditions and contingent situations. 4 Introduction

The driver must pay the utmost attention to the signals of the Most accidents are caused by distraction. The driver must use vehicle and, in particular, the warning lights on the dashboard any on-board information, communication and entertainment and buzzers. Even when the warning lights do not indicate a systems responsibly, especially when the vehicle is in motion. situation of immediate danger, the driver must be cautious in Examples of information, communication and entertainment relation to possible consequences/degeneration of the failure systems are the following: satellite navigation systems, traffic and other information given. information systems (e.g. ITT), media players (e.g. iPod), During routine operations, such as refuelling, precautions telephones with Bluetooth connectivity, etc. (whether merely should always been taken and it is important to check that audio-based or with display). flammable liquid has not been spilled; these precautions must be observed even if the operation is performed by others. It is important to bear in mind that on-board systems may Similarly, before setting off make sure that the doors are be distracting when driving since they may take a driver's closed by checking the warning lights and also manually. attention away from the road for several seconds. The driver must be fully acquainted with the vehicle and its Aftermarket video entertainment systems for the passenger (e.g. controls in order to handle and drive it correctly. Command of TV) must be installed where they cannot distract the driver the vehicle can be acquired/improved by attending the driving while the vehicle is in motion. While the vehicle is in motion, courses held by Ferrari which we strongly recommend. the attention required to use on-board systems must never exceed the high level of attention required to drive safely in The use of terms from the motor sports world (such as F1, accordance with the Traffic Regulations. SPORT and RACE) is merely indicative of the vehicle's competition-derived technology and does not endorse Therefore, these systems may only be used (separately or in inappropriate behaviour on the road which does not comply combination with others) by the driver: with Traffic Regulations. - in complete safety (stopping the vehicle before use if necessary). Operations that are not involved with driving (e.g. changing dashboard functions), must be performed in maximum safety when the vehicle is stationary; Introduction 5

- putting road safety first; for example, under conditions of Strict priority criteria must be observed when driving a vehicle: you poor or limited visibility, looking at a display with active must not therefore take your attention and eye off the road. programmes can be distracting even if you take your eye off In some countries, the use of entertainment/information systems is the road only for a split second; prohibited on vehicles when driving. - ensuring, if the previous vehicle owner has installed systems The driver is responsible for use of these entertainment/ on the vehicle that are NOT APPROVED by Ferrari (car information systems with video screens if they are prohibited in the tuning), that they are fully compatible with the original country where the vehicle will be driven. vehicle equipment. These considerations are not exhaustive, but only refer to a number of general issues that will be specifically dealt with in If the vehicle owner has installed one or more new systems, either this Owner's Manual. fixed or removable, on the vehicle, make sure that these - have the necessary certification; - are fully compatible with the original vehicle equipment (i.e. they do not interfere with it); - are fitted by skilled staff. The Ferrari Technical Service Department and Ferrari Dealers and Authorised Service Centres can provide all the information needed to ensure that they are compatible. 6 Introduction

Introduction Warranty Booklet The aim of this Owner’s Manual is to help you get the best Each new vehicle comes equipped with a “Warranty Booklet”. value from your vehicle and to provide information on routine This contains the vehicle’s warranty validity conditions. maintenance: we advise you to read it carefully before setting This warranty does not affect the buyer's statutory rights as out. The Owner’s Manual should be considered an integral part a consumer, which derive from binding legal norms in his or of the vehicle and must therefore always be kept on board. her favour, in the various states or countries or from European Using the vehicle in a way that does NOT comply with Union regulations, towards the Dealer. the Owner's Manual not only exonerates Ferrari of any The Warranty Booklet also contains the routine maintenance responsibility but also puts the person at great risk. indicated in the “Maintenance Schedule”. Updating The high quality level of the vehicle is subject to constant technological improvements. Therefore, there may be differences between this manual and your vehicle. The Ferrari Sales and Service Network will provide you with all the information on any updates. All specifications and illustrations contained in this manual are accurate as of the date of printing. Spare parts When replacing parts or topping up with lubricants and fluids, we recommend that you use original spare parts and lubricants and fluids recommended by Ferrari. Introduction 7

Service Consulting the manual The information in this manual is necessary for the use and To facilitate reading the manual, the topics have been divided proper care of the vehicle. In addition, Customers will get into sections and chapters. maximum satisfaction and results from the vehicle if they carefully follow the instructions contained in it. We recommend that you have all the checks and services 1. General performed at Ferrari Authorised Workshops since they have Provides general information about your vehicle. highly skilled staff and the necessary equipment. 2. Quick reference guide Please refer to the “Sales and Service Organisation” manual for information on the location of the Ferrari Dealers and Contains all the information you need when using the vehicle Authorised Service Centres. for the first time. The Ferrari Technical Service Department is at your 3. Safety complete disposal for any information and advice. If you have Describes the main safety systems in the vehicle. any doubts about the information provided in this manual or how to use or operate the vehicle, please contact the Ferrari 4. About your vehicle Service Network. Provides all necessary information for use of the vehicle. 5. Advice for Emergency Situations Provides useful advice for solving problems that may occur. 6. Care of the vehicle Provides advice for cleaning, care and routine maintenance of your vehicle. 7. Glossary Explains the main technical concepts. 8. Table of Contents Allows you to quickly identify and locate the information required. 8 Introduction

Within the various sections, special attention must be paid to Abbreviations/Acronyms the parts marked as follows: Some descriptions and terms with particular meanings are found in this manual in an abbreviated form: Warning AC Air conditioning Extreme caution required: failure to comply with the ABS Anti-lock Braking System instructions could constitute a serious risk to personal safety ASR Anti-skid Regulation during acceleration and vehicle protection! DCT Dual Clutch Transmission EBD Electronic Brake-force Distribution ECU Electronic Control Unit Important note ESC Electronic Stability Control Important note: a note containing instructions or information. F1-Trac Traction control derived from the technologies used in the racing sector RHT Retractable Hard Top Environment Warning for environmental protection: useful advice for protection of the environment. Introduction 9

Environmental protection Driving style - Do not accelerate during the starting procedure. Environment - Do not warm up the engine when the vehicle is stationary. - Drive carefully and keep a safety distance that corresponds to the The following chapter contains useful advice for environmental driving speed. protection. - Avoid sudden and frequent acceleration or braking. - Turn off the engine if the vehicle is kept stationary for long Ferrari has designed and constructed a vehicle using technologies, periods of time. materials and devices capable of reducing the harmful impact on the environment to a minimum. - Shift gears using only 2/3 of the speed permitted for each gear. If you use your vehicle with respect for the environment, you too - Use the air conditioning in moderation. will contribute towards environmental protection. - A driving style like that described above protects the vehicle Fuel consumption as well as engine, gearbox, brakes and tyres wear from premature wear and tear, makes driving safer and does not mainly depend on two factors: subject the vehicle to undue fatigue. - use of the vehicle; - driving style. Important note Both factors are influenced by the driver. The vehicle is equipped with exhaust gas control and Use of the vehicle monitoring systems which must always be kept in perfect - Avoid using the vehicle for short trips. working order and controlled regularly. - Check that the tyre pressure is correct. - Check the fuel consumption. - Proper periodic maintenance will contribute to preserving your vehicle in full working order and to protecting the environment. We therefore advise you to respect the service due dates indicated in the “Maintenance Schedule”. 10 Introduction

Directive for the treatment of end-of-life vehicles Bear in mind that specific regulations govern the disposal of vehicle (EU only) parts including batteries, tyres, used oil, etc. For many years, Ferrari has been globally committed to respecting Please contact the Ferrari Service Network for more and protecting the environment by constantly improving its information. manufacturing processes and developing increasingly eco- compatible products. Regulations for the treatment of end-of-life vehicles, implemented in response to the terms of EU Directive 2000/53, require that producers (manufacturers and official importers) collect all the vehicles introduced on the market by the producers themselves at the end of their life cycle, and ensure that these vehicles are processed in an environmentally compatible manner. To hand over your Ferrari at the end of its life cycle for treatment at no additional cost (excluding deregistration and transport), take your vehicle to the nearest Ferrari dealer, which will, at its own expense, transport the vehicle to one of the authorised collection and demolition centres, which have been selected to ensure that all processes for the collection, treatment and recovery of recyclable materials are carried out in an environmentally compatible manner. For further information, visit the website www.ferrari.com. When handing over a Ferrari vehicle at the end of its life cycle: - the vehicle must be complete, containing all the essential elements such as the engine, transmission, bodywork, ECUs and catalytic converters; - the vehicle must not contain any additional refuse. Ferrari is committed to offering its clients a geographically extensive and, as a result, better service, and thanks you for your cooperation in this environmental challenge. Introduction 11

Vehicle keys ........................................................... 14 Alarm system......................................................... 15 Duplicating the keys .............................................. 16 Replacing remote control batteries ......................... 17 Electronic alarm .................................................... 17 Identification and homologation plates and labels .. 20 Dimensions and weights ........................................ 26 Main engine specifications ..................................... 27 Consumption and emissions .................................. 27 Performance.......................................................... 27 Wheel rims and tyres ............................................. 28 Refilling................................................................. 31

1 GENERAL

Vehicle keys Key codes The vehicle is delivered with two identical keys that can be used A CODE CARD is supplied with the keys. This card shows the for: following: - central door locking; - the electronic code; - starting the vehicle; - the mechanical code for the keys, to be given to the Ferrari Service Network if you request duplicates of the keys. - activating/deactivating the alarm system; - opening the luggage compartment lid. Warning Important note The code numbers on the CODE CARD must always be kept in a safe and protected place, not accessible to others. If the keys are lost or stolen, you can request a duplicate from the Ferrari Service Network (see section “Duplicating the keys” on page 16). Important note In the event of a change of ownership, it is essential that the new vehicle owner is provided with all the keys and with the CODE CARD. 14 General

Alarm system - When starting the engine, press the ENGINE START button on 1 the steering wheel: The FERRARI CODE system 1) If the code is recognised, the CODE warning light A on the instrument panel turns off when the check procedure has been The vehicle is equipped with an electronic immobiliser system completed, whereas the EOBD warning light B turns off when (Ferrari CODE) which is automatically activated when the ignition the engine is started once the ECU has completed its diagnostic key is removed. cycle; in these conditions, the protection system has recognised The keys are equipped with an electronic device which transmits the key code and deactivated the immobiliser. a coded signal to the Ferrari CODE ECU. Once this ECU has recognised the signal, it allows starting the engine. 2) If the CODE warning light A stays on, it means that the code has not been recognised. If this occurs, it is advisable to turn Operation the key back to position 0 and then back to II; if the immobiliser Each time the ignition key is removed (see page 89), the protection device remains active, try with the other key provided. system activates the engine immobiliser. Important note If you still cannot restart the engine, contact the Ferrari Service Network. B A General 15

- While driving, with the ignition key in position II: 1) If the CODE warning light A turns on, it means that the system Important note is performing a self-diagnostic cycle. At the first opportunity, Contact the Ferrari Service Network immediately to have all you can stop and test the system: switch off the engine by the keys stored in the system memory. turning the ignition key to position 0, then turn the key back to position II. The CODE warning light A will turn on and should go off within one second. If the warning light stays on, repeat Important note the procedure described previously leaving the key at 0 for more than 30 seconds. Each key provided has its own specific code, which must be stored in the memory of the system control unit. Important note If the problem persists, please contact the Ferrari Service Duplicating the keys Network. If you request additional keys, provided that the conditions to satisfy your request are met, remember that the codes must be 2) If the CODE warning light A flashes, it means that the vehicle is stored (up to a maximum of 7 keys) on all the keys. not protected by the immobiliser. Contact the Ferrari Service Network directly and bring the following with you: - all the keys in your possession; - the CODE CARD for the Ferrari CODE system; - a personal identity document; - the documents proving ownership of the vehicle; - a report of loss of keys made to the relevant authorities. The codes for the keys that are not available when the new B memorisation procedure is performed will be deleted from the memory to prevent any lost or stolen keys being used to start the vehicle. A 16 General

Replacing remote control batteries Electronic alarm If you press one of the three buttons of the key and this does not activate the corresponding function, check that the alarm system The electronic alarm system performs the following functions: - remote control for central door locking/unlocking; 1 functions are operating correctly by using the other remote control - perimeter surveillance, detecting if doors and lids are open; before replacing the two batteries. - motion surveillance, detecting intrusion in the passenger compartment; Replace the remote control batteries as follows: - vehicle movement surveillance. - open the key cover C using a small screwdriver at the position indicated by the arrow; Activation - remove the two batteries E, pushing in the direction indicated by the arrow to release them from the retainer cover D; To turn on the alarm system, press button F on the key: - fit two new batteries of the same type, observing the indicated - the turn indicators flash once; polarity; - the system “beeps”; - close the key cover C. - the red LED on the dashboard flashes; - the central door locking system is activated and the doors are Important note locked. Do not use sharp tools to remove the cover and be careful to The system activates after approximately 25 seconds. avoid damaging the remote control. When the electronic alarm is activated, the user may request opening of the luggage compartment; in this case, the motion and anti-lift sensors are temporarily deactivated. � � F C G General 17

If the luggage compartment is then closed, the sensors will be The alarm system is off and you can now get into the vehicle and reactivated. start the engine. If the turn indicators and the red LED on the dashboard flash To enter the vehicle if the remote control battery is flat, insert the 9 times when you activate the alarm system, it means that one of key into one of the two door locks and turn it to release the lock; the doors or the front/rear lid is open or not closed properly and is the alarm siren will start to sound. therefore not protected by the perimeter surveillance. If this is the Start the vehicle following the standard procedures. The alarm siren case, check that the doors and front/rear lids are closed properly will deactivate. and close any door or lid that is open without deactivating the alarm system: the turn indicators will flash once to indicate that the Deactivating the anti-lift alarm door or the front/rear lid is now closed properly and is protected by the perimeter surveillance. Press button H on the roof panel to deactivate the anti-lift alarm system. When this function is deactivated, the indicator light on the button will flash for about 3 seconds and will then turn off. Warning If the turn indicators and the red LEDs on the dashboard flash 9 times when the alarm system is activated with doors, rear and front lids properly closed, it means that the self-diagnostic feature has detected a malfunction in the system. Contact the Ferrari Service Network to have the system checked. Deactivation To deactivate the alarm system, press button G on the key: - the turn indicators flash twice; H - the system beeps twice; - the red LED on the dashboard goes off; - the dome lights come on; - the central door locking system is deactivated and the doors are unlocked. Pressing button G twice unlocks the doors and also turns on the low beams for 30 seconds. 18 General

Alarm memory Homologation If the CODE symbol (see page 116) appears on the left TFT display for 10 seconds when the vehicle is started after system diagnosis together with the message “Break-in attempted”, this The electronic alarm system complies with EU regulations on elec- tromagnetic compatibility and is marked in compliance. The homologation number is referred to with the following charac- 1 means that an intrusion has been attempted and has activated the ters. alarm. For those markets that require the transmitter and/or receiver In this case, the system will indicate the reason for the alarm marking, the homologation number is found on the component. activation according to the following priority: - LED off twice: lifting sensor alarm Satellite alarm system (optional) - LED off three times: door alarm On request, the vehicle can be equipped with a satellite alarm - LED off four times: luggage compartment lid alarm system in some markets. If the vehicle is equipped with a satellite alarm system, please refer to the “Nav Trak Satellite Alarm System - LED off five times: ignition key alarm. Quick Reference” booklet enclosed with the vehicle documents, for The alarm system memory is reset by turning the ignition key. further information. General 19

Identification and homologation plates and labels G H F E L D M C B N A O P Q R 20 General

1 Ref. Label/plate Position A Low-beam homologation Luggage compartment lid B ECE homologation Luggage compartment lid C Vehicle identification Rear passenger-side door jamb D Airbag maintenance Passenger-side sun visor E Passenger airbag warning (2) Passenger-side sun visor F Unleaded fuel Fuel filler flap G Radiator with antifreeze RH engine compartment cosmetic shield H Engine and gearbox oil label Engine compartment lid L Assembly number Engine compartment M Engine type and number Crankcase N Gearbox type and number Gearbox housing O Tyre pressure and type Driver-side door P TPMS present warning Driver-side door Q Chassis number Windscreen R Original paintwork Luggage compartment lid General 21

A Low-beam homologation C Vehicle identification B ECE homologation D Airbag maintenance 22 General

E Passenger airbag warning G Radiator with antifreeze 1 F Unleaded fuel H Engine and gearbox oil label General 23

L Assembly number N Gearbox type and number M Engine type and number O Tyre pressure and type 24 General

P TPMS present warning R Original paintwork 1 Q Chassis number General 25

Dimensions and weights Wheelbase 2650 mm (104.33 in.) Max. length 4527 mm (178.23 in.) Max. width 1937 mm (76.26 in.) Max. height 1211 mm (47.7 in.) Front track 1672 mm (65.83 in.) Rear track 1606 mm (63.23 in.) Front overhang 1107 mm (43.58 in.) 1672 1606 Rear overhang 770 mm (30.31 in.) Kerb weight 1430 kg (3152.6 lbs)* 1937 * considering the most favourable Optional combination 1213 2650 4527 26 General

Main engine specifications Transmission ratios Type F 136 FB Gearbox ratios Differential/bevel gear pair ratio 1 Number of cylinders 8 Cylinder sequence V 90° 1 = 3.077 Cylinder bore 94 mm (3.7 in.) 2 = 2.185 Piston stroke 81 mm (3.2 in.) 3 = 1.626 5.143 Total displacement 4497 cm3 (274.4 cu. in.) 4 = 1.286 Compression ratio 12.5:1 5 = 1.028 Maximum RPM 9200 RPM 6 = 0.839 (with limiting device) 7 = 0.693 Max. power 416 kW R = 2.791 (565 HP) Corresponding RPM 9000 RPM Performance Max. torque 540 Nm Corresponding RPM 6000 RPM 0 - 100 km/h 0 - 400 m Max. speed < 3.5 s 11.3 s > 320 km/h (198.8 mph) Consumption and CO2 emissions Electrical system Standard version HELE version Supply voltage Alternator l/100 km g/km l/100 km g/km 12 V Nippondenso 165 A SC3 City cycle 19.7 454 15.8 369 Battery Starter motor Motorway 9.7 223 9.4 221 Fiamm 12V - 70 A/h Bosch Combined cycle 13.3 307 11.8 275 L3 VRLA 760A EN General 27

Wheel rims and tyres Wheel rims Front Rear Spare wheel 8.5” J x 20” 10.5” J x 20” 4.5” J x 20” Ferrari-approved tyres Inflation pressure (cold) Front Rear Front Rear Michelin Pilot Super Sport 235/35 ZR20 295/35 ZR20 2.10 bar (30.46 psi) 2.00 bar (29 psi) Bridgestone Potenza 235/35 ZR20 295/35 ZR20 2.30 bar (33.36 psi) 2.30 bar (33.36 psi) Pirelli Pzero 235/35 ZR20 295/35 ZR20 2.10 bar (30.46 psi) 2.00 bar (29 psi) Optional tyres Inflation pressure (cold) Front Rear Front Rear Bridgestone Potenza Run Flat 235/35 ZR20 295/35 ZR20 2.30 bar (33.36 psi) 2.50 bar (36.26 psi) Vredestein spare wheel 145/60 R20 4.20 bar (60.92 psi) Winter tyres Inflation pressure (cold) Front Rear Front Rear Pirelli Winter Sottozero 235/35 WR20 285/35 WR20 2.10 bar (30.46 psi) 2.00 bar (29 psi) 28 General

Correct reading of tyre manufactured in the EU Example: 235/35 ZR20 235 = Nominal width (distance in mm from side to side) 1 35 = Height/width ratio as a percentage Z = Tyre to be used for speeds of over 240 km/h (149 mph) R = Radial tyre 20 = Rim diameter in inches W = Tyre that supports a maximum speed of 270 km/h The tyre manufacture date is included in the description of the tyre: DOT ... 1009 means that the tyre was manufactured in the 10th week of 2009. Correct rim reading Example: 8.5” J x 20” 8.5 = Rim width in inches J = Shape of rim flange (side projection where tyre bead rests) 20 = Rim diameter in inches (corresponds to the diameter of tyre to be fitted) For further information on tyres, see page 235. General 29

Run Flat tyres (optional) The vehicle can be fitted with “Run flat” tyres, if required. This type Warning of tyre has a reinforced side A which allows the vehicle to continue If you are going to use standard tyres on a vehicle that was travelling at moderate speed (80 km/h - 50 mph), even after a originally equipped with “Run Flat” tyres, you must contact the puncture, for a specific distance (100 km - 62 mi). Ferrari Service Network to have the device in the dashboard When the instrument panel receives the “tyre puncture” reprogrammed and prevent warning messages from being information from the tyre pressure monitoring ECU, calculates the displayed on the left TFT display. residual tyre life, and displays a warning in the dedicated area of the left TFT display after 50 km (31 mi). After 100 km (62 mi), a message warning the driver to stop the Environment vehicle will be displayed (for further information, see the “Tyre pressure and temperature monitoring system” paragraph on Maintaining correct tyre pressure helps to improve tyre rolling page 76). and reduce fuel consumption. Warning Observing the recommended wheel alignment values is essential in order to obtain the best performance and the longest life of these tyres. � 30 General

Refilling Parts to be refilled Engine Total system capacity Quantity 10 l Fill with: SHELL HELIX ULTRA SAE 5W-40 Ref. Page 230 1 Oil level between Min. and Max. 2l Oil consumption 1.0 - 2.0 l/1,000 km Gearbox and differential 3.9 l SHELL SPIRAX S5 ATE 75W-90 231 Clutch system and hydraulic controls 8l SHELL DCT-F3 Braking system 1.5 l SHELL BRAKE AND CLUTCH 233 DOT4 Ultra Cooling circuit 16.5 l GLYCOSHELL LONGLIFE at 50% 232 Hydraulic power steering system 1.6 l PENTOSIN CHF 11S 232 Fuel tank 86 l Unleaded fuel 95 RON. 90 Reserve 14 l RHT system Total system capacity 257 ml ARAL VITAMOL ZH-m Oil level between Min. and Max. 34 ml Air conditioning and heating system Compressor 165 cc PAG ISO 46 Coolant 630 ± 30 g DELPHI RL 488 “R 134 A” Windscreen washer/headlight washer fluid tank 5l Mixture of water and glass cleaner 234 General 31

Important note This vehicle is suitable for use with unleaded fuel with a maximum of 10% ethanol (E10). Warning The use of fuel with 10% - 25% ethanol can cause malfunctioning. The use of fuel with over 25% ethanol can cause permanent damage to the engine fuel system parts. 32 General

Opening doors ...................................................... 36 Controls overview .................................................. 37 Seat adjustment .................................................... 39 Steering wheel adjustment ..................................... 40 Rear-view mirrors .................................................. 41 Seat belts .............................................................. 42 Ignition switch ....................................................... 43 External lights and turn indicators .......................... 44 Starting and driving the vehicle ............................... 46

2 QUICK REFERENCE GUIDE

Opening Locking and opening the doors from the inside Doors Warning When a door is opened or closed, the window automatically moves Always check that the doors have been closed properly to down by approximately 2 centimetres / 0.8 inches (to its “target prevent them from opening while driving. position”) to avoid colliding with the upper weather strip. When the door is closed, the window automatically moves up until Both doors can be locked by activating/deactivating the “LOCK/ it reaches the “upper limit”. UNLOCK” B button on the roof panel. To lock the doors, press button B; when the door lock is activated, the light on button B Opening from the outside comes on. To deactivate the door lock, press button B until the Using the remote control, deactivate the alarm and the central door light goes out. locking system, or turn the key in the lock to deactivate the central If you pull handle C to open the door, the window will move down door locking system. to its target position. When the door is closed, it will move up until To open the door, pull handle A: the window will move down to its it meets its upper limit. “target position”. When the door is closed, the window will move When the opening handle is operated, both doors are unlocked. up until it meets the upper limit. B � C 36 Quick reference guide

Controls overview 1 1 1 2 3 2 6 5 4 Ref. Control Page Ref. Control Page 1 Adjustable air vents 186 4 Light switch 132 2 Glove compartment 187 5 External rear-view mirror adjustment control 182 3 Right TFT display controls (NIT) 124 6 Left TFT display controls 96 Quick reference guide 37

Ref. Control Page Ref. Control Page 7 Left TFT display 96 16 Front Lift system control (optional) 165 8 Rev counter and gearbox display 121-122 17 Backlite rear screen control 93 9 Right TFT display 124 18 Power window controls 92 10 Turn indicators 134 19 “LAUNCH” control 164 11 Windscreen washer/wiper lever 129 20 “R” reverse control 146 12 “Manettino” control 126-155 21 Air conditioning controls 183 13 “ENGINE START” button 126 22 “AUTO” control 149 14 Suspension damping delink button 128-161 23 Hazard warning lights control 135 15 High beam and flashing lever 132 24 Retractable hard top opening/closing control 140 25 Glove compartment opening button 187 7 8 9 18 19 20 17 10 10 16 21 15 11 14 12 13 25 24 23 22 38 Quick reference guide

Adjustments Backward/forward adjustment Pull lever B up and slide the seat forward or backward to the Seats desired position. Release the lever and “wiggle” in the seat to check that it is locked in place. Warning As with all adjustment, seat adjustment must be performed when the vehicle is stationary. Warning The backward/forward adjustment must consider the fact 2 that airbag devices are placed in front of the driver and the Correct adjustment is very important for enhanced driving comfort passenger (see page 63). and maximum efficiency of the passive safety systems. Correct adjustment ensures there is adequate space between the airbag and the driver/passenger (see page 63). Basic seat The seat position can be adjusted using the special controls. Seat back rake adjustment Turn knob C clockwise or counterclockwise until it reaches the required position. B C Quick reference guide 39

Tilting the backrest Steering wheel To tilt the seat, pull lever L up and push the backrest towards the The steering wheel can be adjusted for rake and reach. front of the vehicle. When the backrest goes back into position, it will automatically Warning block once it has reached the correct position. Do not adjust the steering wheel when the vehicle is moving. For further information on basic seat adjustment, refer to pages 175-176. Mechanical adjustment Electrically-adjustable seat (optional) 1) Unlock lever X by pushing it forward. 2) Adjust the position of the steering wheel. For further information on adjustment of the optional electrically- adjustable seat, refer to pages 177-178-179. 3) Lock the steering wheel by pulling lever X until it locks into place. Super Racing seat (optional) Electric adjustment (optional) For further information on adjustment of the optional Super Racing seat, refer to page 180. It can only be adjusted if the ignition key is in position II. Move control A to the left of the steering column. On versions with a driver's seat with memory, the position of the steering wheel is memorised together with the position of the external rear-view mirrors when the seat position is memorised. X L A 40 Quick reference guide

Rear-view mirrors 2) Mirror positioning: move control C in the four directions (up – down – right – left) to adjust the selected mirror. Internal electrochromic mirror (optional) 3) Mirror closure (optional): turn control C to the lower central Hold the internal rear-view mirror and move it to the required lock position to close the rear-view mirrors. position. Once adjusted, move the control C into the upper central position On request, the internal rear-view mirror can be fitted with an electrochromic mirror that automatically darkens to reduce the where it will be locked in order to avoid changing the external mirror setting inadvertently. 2 dazzling effect of the reflected light on the driver. The speed with The mirrors will yield in both directions in the event of a collision: which the mirror darkens depends on the intensity of the light. if necessary, the mirrors can be pushed both backwards and By pressing button B you can activate/deactivate the electrochromic forwards. mode. When the electrochromic mode is activated, the green LED D comes on. Warning External rear-view mirrors The rear-view mirrors must always be positioned correctly while These mirrors can be electrically adjusted using the control C (with driving. the ignition key in position II) and are equipped with defogging Do not adjust the rear-view mirrors when the vehicle is moving. elements. 1) Mirror selection: turn control C to the left or right lock position to select the mirror that requires adjusting. D C C B Quick reference guide 41

Seat belts If the driver’s seat belt is not fastened, when you turn the ignition key to position II, the warning light on the instrument panel illuminates and remains lit as long as the seat belt is not fastened. Warning The seat belts must be properly adjusted and fastened at all Unfastening the seat belts times. • Push the release button E. Correct use of the seat belts can reduce the risk of serious injury • Guide the latch plate A back to its rest position. in the event of an accident or if the vehicle overturns. Warning Fastening the seat belts Do not allow children to be held on a passenger’s lap using only After positioning the seat correctly: one seat belt for both of them. • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it For further information, refer to the “Safety” chapter on page 56. out, let it wind back a little and pull it out again without jerking it). • Make sure that it has clicked into the locked position: hold the belt and pull it to check that the latch plate has been inserted correctly. • Position the seat belt correctly. � A � E 42 Quick reference guide

Ignition switch Warning The ignition key can be turned to 2 positions: Position 0 - Stop Never remove the key when the vehicle is moving! Engine off, key removable. The steering wheel will lock with the first turn of the steering wheel. When the key is even only partially extracted, the steering column is locked. Always remember to remove the key from the ignition when you get out of the vehicle! 2 The hazard warning lights and parking lights can be activated. Never leave children unattended in the vehicle. To facilitate steering wheel release, turn the steering wheel slightly clockwise or counterclockwise while turning the ignition key. Key lock Position II - Start If more than 20 seconds elapse after turning the key to position 0, When the key is turned to this position (key-on) the signals the key lock device must be released to remove the key: generated by the vehicle systems are checked. press button K and remove the key at the same time. The left and right TFT displays are activated on the instrument panel and when the signals have been checked, the gearbox display comes on (see page 122). For further information, see page 89. II 0 Quick reference guide 43

External lights and turn indicators High beams To turn on the high beams when the light switch A is set to , Light switch pull back lever B on the steering wheel. The switch A, on the dashboard to the left of the steering wheel, When the high beams are on, the relative warning light on the can be set to five different positions: instrument panel comes on. 0 Lights off Then push lever B towards the dashboard or pull it back to turn off the high beams and turn on the low beams. Running and number plate lights on (*) Low beams on (*) Important note Parking lights Follow the Road Regulations of the country you are travelling in AUT Automatic operation of the external lights according to for using the high beams. ambient light. (*) The relative warning light on the instrument panel comes on. Flashing the headlights The headlights can be flashed by pushing the left-hand lever B towards the dashboard. B A 44 Quick reference guide

Turn indicators Rear fog lights Quickly press the left indicator or right indicator button C on the The rear fog lights are turned on only if the high beams or low steering wheel to switch on the relevant turn indicator. beams are on when button D is pressed. The relative warning light or on the instrument panel comes on. Important note The turn indicator goes off when the steering wheel is realigned. Holding down one of the two C buttons (for more than Use the rear fog lights only in poor visibility conditions. 2 0.3 seconds) temporarily switches on the relevant turn indicator: it Hazard warning lights is switched off after 3 flashes (“lane change” function). Press button E to turn on the hazard warning lights. All the turn indicators will start blinking intermittently; these lights will operate with the ignition key in any position. When the lights are on, the relative warning lights on the instrument panel and the button flash. To turn them off, press the button again. For further information, refer to the “Lighting” paragraph on page 132. C C D E Quick reference guide 45

Starting and driving the vehicle System start-up Warning After turning the ignition key to position II (key-on), the left and Contact the Ferrari Service Network. right TFT displays are activated on the instrument panel and system diagnosis is performed. During diagnosis, which lasts 5 seconds, a check is performed on the warning lights on the panel and the Important note presence of any faults is checked. The vehicle is equipped with an electro-hydraulically controlled Once the system check has been completed, the gearbox display gearbox system operated by means of paddles on the steering is activated and the letter “P” (Parking) or “N” (Neutral) will be wheel. displayed. The default setting for the DCT gearbox is always “Automatic” mode (see page 149). Important note Every time the vehicle is started, the DCT gearbox is in “Auto BEFORE YOU DRIVE easy exit” mode (see page 149) unless the vehicle was in If the warning light A does not turn off after diagnosis, “Automatic” mode when the engine was turned off. indicating a fault in the gearbox also shown by the symbol and To exit the “Auto easy exit” mode operate the UP and DOWN special message on the left TFT display (see page 121), contact paddles (while the vehicle is moving) or press the AUTO button the Ferrari Service Network. on the centre console. A 46 Quick reference guide

Starting the engine Important note Before starting the engine, make sure that the alarm system and all Immediately release the UP and DOWN paddles or button R electrical devices with high power absorption are turned off. after the gearbox display shows that the gear has been engaged; • Make sure that the electric parking brake is applied and that the a prolonged manoeuvre would cause the gearbox failure doors are closed. warning light to turn on (see page 121) and triggering of the buzzer. • Hold the brake pedal down when starting the engine. 2 Warning Important note Do not press the accelerator pedal. None of the gears can be engaged if the luggage compartment lid is open or not properly closed. When the vehicle is stationary, • Turn the ignition key to position II and wait for the gearbox with the driver-side door open or not properly closed and the display to come on. brake pedal released, the system disengages the gear engaged • Press the ENGINE START button (see page 126) and release it as after approximately two seconds. soon as the engine starts. Do not hold the ENGINE START button down for a long time. If the engine does not start, turn the key back to position 0 and wait for the gear display to go off before retrying. Warning DOWN UP Hold the brake pedal down while starting the engine. Quick reference guide 47

If the engine fails to start after several attempts, check for one of the following causes: Warning • insufficient speed of the starter motor (flat battery) If the “UP” and “DOWN” paddles are not working, the message • ignition device faulty “Depress brake pedal and press LAUNCH to engage gear” will • electrical contacts faulty appear on the left TFT display; you can therefore engage the gear by pressing the LAUNCH button on the centre console (see • fuel pump fuses blown. page 164) and the brake pedal. Warming up the engine In these cases, the “Launch Control” function is not available. If the engaged gear was R, the LAUNCH button must be pressed Do not run the engine at high speed until the engine oil temperature twice to engage 1st gear. has reached at least 65-70 °C (149-158 °F), approximately. Starting the vehicle Important note With the engine started, the vehicle stationary and the brake pedal pressed, pull the right-hand “UP” paddle towards the steering When reverse is selected, an acoustic safety signal beeps wheel to engage 1st gear. intermittently as long as “R” is engaged. Release the brake pedal and press the accelerator to start off. With the engine running and the vehicle stationary, you can change If the system automatically selects 2nd gear when attempting to directly from 1st or 2nd gear to R (reverse) by pressing R and from shift from R to 1st gear, this indicates that 1st gear has jammed. reverse to 1st by moving the UP paddle. Therefore, this is not a malfunction, as it falls within the system operating logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has jammed. During prolonged stops with the engine running, it is advisable to keep the gearshift in “N”. R Important note If you allow the vehicle to move forward in N, when UP or DOWN is requested, a gear will be engaged that corresponds to the speed of the vehicle. 48 Quick reference guide

UP-shifting Stopping the vehicle Use the right-hand UP paddle without releasing the accelerator When the vehicle stops, the system automatically engages 1st gear pedal. unless Neutral has already been requested. An UP-shift request is not accepted when engagement of the When the vehicle is stationary and the engine is running, hold the requested gear forces the engine to underrev or if an UP-shift is brake pedal down until ready to move off again. already in progress because of engine overrevving. For further information, see page 147. Switching off the engine 2 The engine can be switched off with the gearbox either in “N” or DOWN-shifting with a gear engaged. Use the left-hand DOWN paddle without releasing the accelerator After turning the ignition key from position II to position 0, the pedal. gearbox display will remain on for a few more seconds to display A DOWN-shift request is not accepted if engagement of the the engaged gear. If the gearbox is in “N” a buzzer will sound. requested gear forces the engine beyond a certain RPM, depending Before switching off, the letter “P” is displayed on the gearbox on the gear requested, or if a DOWN-shift is already in progress display to inform the driver that the Park Lock has been activated. because of engine underrevving. For further information, see page 147. Warning “N” (Neutral) request Never leave the vehicle with the gearbox in “N”. Always make sure that the letter “P” (Parking) appears on the gearbox display. With the engine running, pull both UP and DOWN paddles towards the steering wheel at the same time without pressing the brake pedal For further information, see page 163. to request neutral “N”. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. Quick reference guide 49

Passive safety......................................................... 54 Active safety .......................................................... 55 Seat belts .............................................................. 56 How to fasten seat belts ........................................ 58 Pretensioners......................................................... 60 Auxiliary Occupant Protection Systems ................... 62 Driver and passenger airbags .................................. 63 Side airbags........................................................... 68 Fuel inertia switch.................................................. 71 ABS and EBD ........................................................ 72 Stability and Traction Control ................................ 73 Electric parking brake ............................................ 75 TPMS (optional) ................................................... 76

3 SAFETY

Ferrari has designed and built a high performance vehicle. Emissions In order to take advantage of the safety systems described below, it is essential to comply with the indicated regulations. Warning • The exhaust gas generated by the running engine may be Special recommendations hazardous, especially when in closed spaces. As well as This vehicle has been built to comply with homologation consuming oxygen, the engine discharges carbon dioxide, regulations that also concern safety and environmental protection. carbon oxide and other toxic gases. These high technological standards must always be accompanied by • Fuel is highly inflammable and emits vapours which may be careful and cautious driving. noxious if inhaled. Particular attention must be paid to: Do not use naked flames or create sparks near the open fuel • Overheated components. High temperatures develop in the tank or in any other condition where fuel comes into contact engine compartment near the exhaust system. Do not park the with air. vehicle on paper, grass, dry leaves or other flammable materials. They could catch fire if they come into contact with hot parts of Lubricants the exhaust system. Do not fit other heat shields or remove those fitted on the exhaust system. Do not let flammable substances Warning come into contact with the exhaust system. • Moving parts of the vehicle such as belts, fans, etc. They must • The oils used may also be flammable: take the same always be adequately protected. Do not remove the guards or precautions as those adopted for fuel. operate on the moving parts without taking due precautions. • Installations under pressure such as braking system, air Flammable fluids conditioning system, cooling system and lubrication system may create pressures inside them. Do not perform any operation which Warning may cause gas or liquids to spill out with the risk of injury to persons and damage to things. • The fluid in the battery is poisonous and corrosive. Do not let it spill out and come into contact with the skin, eyes or objects. Do not use naked flames or create sparks near the battery. Fuel inertia switch • See page 71. 52 Safety

Warning Warning Seat belts must be worn at all times and must be properly Each seat belt has been designed to protect only one occupant. fastened and adjusted! If more than one person uses the same seat belt, the risk of Correct use of the seat belts can significantly reduce the risk injury in the event of an accident is increased. and severity of injury if an accident occurs or if the vehicle Do not sit babies, small children or other persons on your lap. overturns. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning For an effective restraining action, the seat belt must be fastened 3 correctly with the seat backrest in the upright position. The seat belt is fastened correctly when the upper part of the belt crosses the centre of the shoulder (not the neck) and the abdominal section is fitted over the hips (not the abdomen). Make sure that the belt is not twisted and that it passes closely over your body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Avoid wearing bulky clothing that may interfere with the proper operation of the seat belts. Safety 53

Passive safety - occupant protection system ECU The passive safety system has been designed to reduce the risk and - ECU auxiliary sensors severity of injury if an accident occurs. - instrument panel warning light (see page 63) The vehicle is equipped with the following seat belts: - inertia switch. - 3-point driver's seat belt with pretensioner and load limiting device (see page 56) Warning - 3-point passenger seat belt with pretensioner and load limiting device (see page 56). The protective action of the airbags is always integrated with the seat belts and the pretensioners. The compulsory use of the seat belt is provided by the national regulations (in Italy, for Warning example, by the Codice della Strada, i.e. Traffic Regulations). Auxiliary safety systems are not a substitute for seat belts. All occupants must always wear a seat belt. Correct use of the Deformable body seat belts combined with use of the auxiliary safety systems The deformable body absorbs shock and distributes it over the provides optimal protection to the occupants in various types of entire structure of the vehicle allowing progressive deceleration. collisions. The passenger compartment structure, on the other hand, has been designed to provide maximum resistance without undergoing The vehicle also has the following auxiliary occupant protection deformation in order to guarantee a protective survival cell for the system components (see also page 60 “Auxiliary occupant occupants. protection systems”): - front driver's airbag (for operating functions see page 63) - front passenger airbag (for operating functions see page 63) - driver's head protection side airbag (head bag) (for operating functions see page 68) - passenger head protection side airbag (head bag) (for operating functions see page 68) - seats (see page 175) - deformable body 54 Safety

Active safety The aim of the active safety system is to reduce the risk of accidents and injury severity. The vehicle has been designed to provide a high level of safety for whoever uses it. The following systems are specific active safety components: • braking system • air conditioning and heating system • external lights • buzzer and warning lights (flashing). 3 The braking system includes the mechanical brake system and the electronic stability and traction control system (ABS and EBD): this is designed to prevent the wheels from locking and to provide good handling and stability. In some situations, fast acceleration is important to get out of dangerous situations. However, always use the accelerator with extreme caution. During acceleration of the driving wheels, the anti- skid system may help you in certain dangerous situations. The air conditioning and heating system in the passenger compartment can add to driving comfort and keep you alert so that you can react quickly when necessary. It is very important to be able to see the road clearly and be seen and external lights must be turned on when the conditions so require. Safety 55

Seat belts Statistics show that when used correctly, seat belts reduce the risk Warning of injury in various types of crashes including the risk of ejection For an effective restraining action, the seat belt must be fastened from the vehicle and impact with the interior of the vehicle. correctly with the seat backrest in the upright position. If not unfastened, the seat belts do not provide any type of The seat belt is fastened correctly when the upper part of the protection. Before every trip, always make sure that all occupants belt crosses the centre of the shoulder (not the neck) and the are wearing their seat belts. abdominal section is fitted over the hips (not the abdomen). Make sure it is not twisted and that it passes closely over your Warning body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. Seat belts must be worn at all times and must be properly fastened and adjusted! Avoid wearing bulky clothing that may interfere with the proper operation of the seat belts. Correct use of the seat belts can reduce the risk of serious injury in the event of an accident or if the vehicle overturns. The seat belts have a lap-shoulder belt with an automatic emergency-locking retractor and are fitted with a pyrotechnic- powered pretensioner and an automatic system that reduces the force applied to the occupant. 56 Safety

Warning Warning Do not let the seat belts come into contact with cutting edges. Periodically check the condition of the seat belts. If the belt They may get damaged and may consequently break in the shows signs of wear, it must be checked by a qualified person event of a collision. and replaced if necessary. Contact the Ferrari Service Network immediately. Warning Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. 3 The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not sit babies, small children or other persons on your lap. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning Do not attach or pin anything onto the seat belts: they may get damaged and may consequently break in the event of a collision. Warning If a seat belt has come into contact with cutting edges or was somehow perforated, we recommend that you have it immediately replaced by the Ferrari Service Network. Safety 57

How to fasten seat belts • Make sure that it has clicked into the locked position: hold the belt and pull it to check that the latch plate has been inserted correctly. Warning • Position the seat belt correctly. For an effective restraining action, the seat belt must be fastened If the driver’s seat belt is not fastened, when you turn the ignition correctly with the seat backrest in the upright position. key to position II, the warning light D on the instrument panel The seat belt is fastened correctly when the upper part of the lights up and remains lit until the seat belt is fastened. belt crosses the centre of the shoulder (not the neck) and the 55 seconds after a speed of 10 km/h (6 mph) is exceeded, a buzzer abdominal section is fitted over the hips (not the abdomen). sounds warning the driver that the seat belt is not fastened. Make sure it is not twisted and that it passes closely over your When a speed of 20 km/h (12 mph) is exceeded, the buzzer body; if not, in the event of a head-on collision, it may move activates immediately and stops after 90 seconds. and cause injury to the abdomen. This acoustic signal is emitted only once, even if the vehicle speed Avoid wearing bulky clothing that may interfere with the proper goes above and below the above mentioned limits. It is repeated operation of the seat belts. (when the vehicle speed is in the indicated ranges) only if the seat belt is fastened and unfastened again or, in any case, every time the Once you have adjusted the seat correctly (see page 175): engine is turned off and then on. • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it out, let it wind back a little and pull it out again without jerking it). � D � 58 Safety

Warning Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not sit babies, small children or other persons on your lap. 3 If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Unfastening the seat belts • Push the release button E. • Guide the latch plate A back to its rest position. A E Safety 59

Pretensioners When a pretensioner is activated, a small amount of smoke is released. This smoke is not harmful. The seat belts are fitted with pyrotechnic-powered pretensioners. The pretensioner is activated by the airbag ECU when there is a sufficiently severe head-on collision (impact direction between 11 Warning and 1 o'clock p.m.) or a sufficiently severe side collision. The belt Activation of the pretensioners only depends on the status of the will rewind a few centimetres just before the restraining action seat belts and is not affected by the occupants' presence. begins, thereby improving the fitting across the occupant's body. If the seat belt is not fastened, the pretensioner will not activate, Activation of a pretensioner is signalled by the illumination of the even if the seat is occupied. warning light A on the instrument panel. The seat belts are fitted with a load limiting device. The load Warning limiting device is located in the belt retractor and allows controlled Pretensioners that have been activated will no longer function release of the belt during a collision thereby limiting the impact and may not be repaired under any circumstances. Contact the that the belt has on the occupant's body. Ferrari Service Network for replacement. Maintenance of seat belts and pretensioners • Following a serious collision, replace the seat belts that were worn at the time even if they do not appear to be damaged. • Periodically check that the screws on the anchor points are tight and that the seat belt is in perfect condition and slides smoothly. A • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. • To clean the seat belt, wash it by hand with mild soap and water and let it dry. Do not use strong detergents, bleach or aggressive solvents, as they can weaken the fibres. Make sure the retractors do not get wet: proper functioning is only ensured if they are kept dry. • The pretensioner requires no maintenance or lubrication. 60 Safety

If immersed in water or mud, it must be replaced. • Pretensioners must be replaced at regular intervals as indicated in the “Warranty Booklet”. Important note All work on any part of this safety system must be performed by the Ferrari Service Network. Warning Removing or making modifications of any kind to the seat belts, 3 belt retractors and pretensioners is not allowed. Maintenance work involving strong impacts, vibrations or heating of the pretensioner area may activate them; vibrations caused by road bumps will not have this effect. Safety 61

Auxiliary Occupant Protection Systems The front driver's airbag and front passenger airbag have been designed to increase the level of protection given by the seat belts in the event of a head-on collision (see page 61). Warning The driver's head protection side airbag and passenger head Auxiliary Occupant Protection Systems are not a substitute for protection side airbag have been designed to increase the level of seat belts but increase their efficiency. Correct use of the seat protection given by the seat belts in the event of a side collision belts, with the supplementary action of the Auxiliary Occupant and are placed between the occupant’s head and external structures Protection Systems, offers maximum protection in the event of a which could penetrate the passenger compartment and cause injury head-on collision or vehicle roll-over. (see page 66). Auxiliary Occupant Protection System components The Auxiliary Occupant Protection System components are: - Seat with built-in headrest. - Dual-stage front driver's airbag. - Dual-stage front passenger airbag. - Driver's head protection side airbag (head bag). - Passenger head protection side airbag (head bag). - Driver's seat belt (3-point with pretensioner and an automatic system that reduces the force applied to the occupant). - Passenger seat belt (3-point with pretensioner and an automatic system that reduces the force applied to the occupant). - Electronic Control Unit (ECU). - Additional sensors. - Instrument panel warning light. - Deformable body. 62 Safety

Warning Warning The warning light A comes on when the ignition key is turned The front airbags have been designed not to inflate if a minor to position II. If no malfunctions are detected, it goes out after collision occurs. The seat belts have been designed to reduce 4 seconds. If the warning light does not come on, if it remains the risk of injury if a minor collision occurs. on or if it comes on while driving, contact the Ferrari Service Network immediately. Warning Driver and passenger airbags The driver and the passenger must maintain a distance of at Warning least 25 cm (10 in.) from the steering wheel and the dashboard. Always drive with your hands on the rim of the steering wheel 3 so that in the event of activation, the airbag can deploy without The front airbags do not provide protection in the event of obstruction. side-on collisions, some head-on/angular collisions, roll-overs Driving with your hands on the steering wheel spokes or on the or subsequent collisions (if there is a second collision once the airbag cover increases the risk of injury for your wrists and arms. airbags have been deployed in an earlier collision). The seat belts have been designed to reduce the risk of injury in the event of a roll-over or subsequent collision. A 2 5cm At least Safety 63

Warning Environment The front passenger must be seated correctly and must avoid When the system is activated, gases are released in the form putting hands, feet or legs on the dashboard since if the front of fumes, together with the gas used for inflating the airbags. airbag is activated, it may cause injury to legs and prevent the These gases are not harmful. airbag from working properly. The driver's airbag has been designed to be deployed according Operating to the following strategy: The front airbags are controlled by an ECU which activates them • For low severity crashes, the airbag control unit will not deploy when there is a sufficiently severe head-on collision (direction of the airbag. impact between 11 and 1 o'clock p.m.). • For crashes of higher severity, the control unit will deploy the In the event of a collision with an impact force that causes driver airbag in low energy mode. deceleration that exceeds the value set for the internal sensor, the • For crashes of even higher severity, the control unit will deploy ECU will transmit a signal to deploy the airbags. The airbags will the driver airbag in high energy mode. begin to inflate, breaking the cover along the breakage line and will deploy completely in a few tenths of milliseconds. Once deployed, The passenger airbag has been designed to be deployed they will serve as protection between the driver and/or passenger according to the following strategy: and structures that could cause injury. • For low severity crashes, the airbag control unit will not deploy The airbags deflate immediately afterwards. the airbag. • For crashes of higher severity, the control unit will deploy the Warning passenger airbag in low energy mode. • For crashes of even higher severity, the control unit will deploy The driver and passenger should not carry objects (drink cans the passenger airbag in high energy mode. or bottles, pipes, etc.) that may cause injury if the airbags are activated. Warning Persons, animals or items must not be placed between the airbags and the occupant. The driver and passenger must always fasten their seat belts and sit in an upright position, as far as possible away from the airbag, in order to have optimal protection in all types of collision. 64 Safety

Warning Important note Always keep the backrest of your seat in the upright position Do not cut or tamper with the connectors of the airbag harness and sit with your back properly resting against it. or on the airbag modules. Important note Warning Do not modify the system components or wiring, under any Do not cover the steering wheel and the padded panel on the circumstances. dashboard on the passenger’s side with adhesive tape or treat it With the ignition key inserted and in position II, although the in any way. 3 engine is off, the airbags can still be activated when the vehicle is stationary if it is hit by a moving vehicle. Warning Remember that if the ignition key is set to 0 none of the safety Do not place objects above or near the top of the dashboard devices (airbags or pretensioners) is activated in the event of a and the steering wheel. collision; failure of the airbags to inflate in these circumstances is In the event that the airbags are deployed, these objects would not indicative of a system malfunction. be projected into the passenger compartment at a high speed that would seriously jeopardise the safety of the occupants. Warning The airbag modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Booklet” EVEN if the vehicle has NOT been involved in a collision. Safety 65

Warning Important note Do not modify the airbag modules in any way (indicated in The airbag system components have been specially designed the relevant picture). Do not damage the airbag modules (for only for this specific vehicle model. Do not use them on a example pinning something onto them or pressing objects different vehicle model, as this may cause serious damage and against their covers). consequent injury, even fatal, to the occupants in the event of an If, for any reason, an airbag cover gets damaged, have the airbag accident. module immediately checked by the Ferrari Service Network. Activation of a damaged module could cause serious or fatal Warning injuries. Damaged or defective components of the airbag system cannot be repaired and must be replaced. Important note Incorrect operations performed on the system components may Do not remove or dismantle parts of the steering wheel, cause failures or accidental deployment or failure of the airbags dashboard or door panels; if necessary, this procedure should to inflate with consequent damage and injury, even fatal. only be performed by a Ferrari Service Network Centre. Environment Important note To scrap the vehicle, please contact the Ferrari Service All the airbag system components must be replaced after an Network to have the airbag system deactivated. accident that caused airbag deployment. Important note Following an accident not involving airbag deployment, contact the Ferrari Service Network to have the system checked and any system components that may be damaged or malfunctioning replaced. 66 Safety

Important note Warning If the vehicle has been stolen or there has been an attempted The passenger seat is not suitable for installing universal theft, have the airbag system checked by the Ferrari Service ISOFIX child car seats. Network. Since the airbag system cannot be deactivated, rear-facing child seats must not be installed. Important note When transporting children who are less than 1.5 m tall, contact the Ferrari Service Network. The label E on the passenger-side sun visor bears the airbag system expiry date. When this expiry date is approaching, contact the Ferrari Service Network to have the system 3 replaced. The label F indicates the presence of the airbag system. F E Safety 67

Side airbags Warning Warning When the ignition key is turned to position II, the warning light A will come on. If no malfunctioning in the airbag system Airbags are not a substitute for seat belts, but they increase their is detected, it will go off after 4 seconds. If the warning light efficiency. Correct use of seat belts, with the supplementary does not come on, if it remains on or if it comes on while action of the side airbags, offers maximum protection in the driving, contact the Ferrari Service Network immediately. event of a collision or vehicle roll-over. Operating Side airbag system components The side airbags are controlled by the ECU that activates them when a sufficiently severe collision occurs. Warning In the event of a side collision with a force of impact exceeding the limit set by the ECU, this will transmit a signal that activates the The side airbags fitted on the vehicle have not been designed pretensioner and the side airbag on the impact side. to reduce the risk of being thrown out in the event of vehicle roll-overs. The vehicle has 2 side airbags, one in the driver-side door and the other in the passenger-side door. The side airbag system consists of 2 airbags, one for each door. In the event of a side collision, the airbag on the impact side deploys immediately to protect the occupant’s head. A 68 Safety

The airbag will start inflating, opening its cover along the breaking line, until it is fully deployed (in a few hundredths of seconds). Warning After deployment, the side airbag will be positioned as a protection Never modify the airbag modules. Do not damage the airbag between the driver’s or passenger’s head and the external structures modules or the trim panels covering (upper area of door panel), which could penetrate the passenger compartment and cause injury. by pinning objects onto them or pressing objects against their The airbags deflate immediately afterwards. respective covers, for example. Side airbag activation is not affected by the passenger's height or If, for any reason, an airbag cover gets damaged, have the airbag weight. The side bag is activated whenever the airbag ECU detects module immediately checked by the Ferrari Service Network. a collision of a sufficient impact force for deployment. Activation of a damaged module could cause serious injuries. Warning 3 Never drive with your head out of the window as this places Important note your head and neck in the airbag deployment area. In the event Please consider that the airbag ECU is not capable of of a side-on collision, this position increases the risk of being automatically detecting damages involving the airbag covers. thrown out of the vehicle and compromises the protective effect of the side airbags. Do not cover the upper part of the driver-door and passenger- door panels with adhesive tape or material and do not treat them in any way. Warning Never place an object over or near the airbag covers. Warning In the event that the airbags are deployed, these objects would After deployment, the airbag components can no longer offer be projected into the passenger compartment at such high speed any protection; therefore, they cannot be repaired and must be as to seriously jeopardise the safety of the occupants. replaced. After activation of a side airbag, have it replaced by the Ferrari Service Network. Safety 69

Warning Important note The airbag modules are subject to wear and tear and must be Never remove the door panel. If required, this operation must replaced at the intervals indicated in the “Warranty Booklet” be performed by the Ferrari Service Network. EVEN if the vehicle has NOT been involved in a collision. Important note The label E on the passenger-side sun visor bears the airbag system expiry date. When this expiry date is approaching, contact the Ferrari Service Network to have the system replaced. E 70 Safety

Fuel inertia switch The fuel inertia switch is a safety device which deactivates the fuel pump relays if a collision occurs. A symbol appears on the left TFT display and the hazard warning lights come on to indicate that the switch has been activated. When the fuel inertia switch is activated, the doors are also unlocked (if locked) and the central dome light comes on. 3 Warning The fuel pump relays can be reactivated by pressing the button in the battery compartment which can be accessed by opening the passenger side footrest. Safety 71

ABS and EBD In the event of ABS activation under braking, these regulation cycles will be repeated until the car comes to a stop or pressure on The ABS system is a safety device which activates to prevent wheel the brake pedal is reduced. locking if the driver presses the brake pedal too sharply, especially In addition, the system offers the following advantages: under low grip conditions. - Driving stability (no skidding): even in the event of sharp braking The system is composed of: approaching wheel locking. - electro-hydraulic unit - Manoeuvrability (no side-skidding on sharp turns). - electronic brake-force distribution EBD This means that even when an emergency situation requires sudden - four speed sensors on the wheels, incorporated in the bearings braking, the driver can avoid obstacles, or brake on a curve, without - the entire ESP sensor system (steering angle sensor, affecting the vehicle stability. accelerometer, yaw sensor, etc.). These features add to the vehicle’s standard braking system, Warning without changing its characteristics. ABS system performance remains unaltered as long as the speed limit for the tyre side grip is not exceeded. If this limit is Important note exceeded, vehicle skidding cannot be avoided. When the ABS system is active, during emergency braking or in poor grip conditions, a “pulsing” sensation will be felt through - Optimal braking distance: the brake pedal. Hold the brake pedal down to continue the depending on the type of road surface, the braking distance may braking action. be reduced by as much as 40%. When one of the wheels starts locking, the hydraulic control unit Warning controls the braking circuit by running a 3-phase cycle: The ABS system does NOT exempt the driver from driving - reduction (if necessary) carefully and responsibly at all times. - maintenance - pressure increase in the hydraulic circuit. 72 Safety

To provide optimal control in different driving and grip conditions, Important note four different settings have been developed: The ABS system cannot compensate for driving too fast for - Level 1: (Manettino set to WET) ensures stability and maximises traffic or road conditions, worn tyres, worn braking system traction on every type of road surface, both in low and very low components or driving errors. grip conditions, by means of engine and brake control (in this condition, the standard ASR system is activated instead of the F1- The ABS system has been designed for the sole purpose of Trac function). assisting the driver in controlling braking under extreme conditions - Level 2: (Manettino set to SPORT) ensures stability and in which he/she could instinctively cause the wheels to lock. maximises traction only in medium- to high-grip conditions by FBP - Ferrari Brake Prefill optimising engine and brake control. - Level 3: (Manettino set to RACE) enhances the racing features 3 of the vehicle by reducing engine control to a minimum and Brake design parameters provide a set distance between the maximising brake control. This mode is designed to ensure brake pads and discs (the “air gap”): as soon as the brake pedal is stability on the race track in high grip conditions only. pressed, the presence of the air gap leads to a slight delay in brake response. - Level 4: (Manettino set to CT OFF) further enhances the racing style performance of the vehicle: F1-Trac traction control The FBP (Ferrari Brake Prefill) system eliminates the air gap by is deactivated whereas stability control remains active when a applying slight pressure to the braking system as soon as the certain level of sideslip is exceeded. F1-Trac traction control is off. accelerator pedal is released just before braking. This results in Stability is NOT ensured. more immediate brake response and reduces braking distance during emergency braking thereby improving safety. - Level 5: (Manettino set to ESC OFF) ESC off. Stability is NOT guaranteed, but all the other auxiliary systems such as the ABS, EBD and the E-Diff 3 electronic differential remain active. During ESC - Electronic Stability Control braking, the VDC system remains active. The ESC system consists of two main systems: VDC Vehicle Dynamics Control, performed through the braking system F1-Trac traction control, performed through engine torque modulation, depending on maximum grip on the road and secondary systems that are always active such as the ABS and EBD. Safety 73

F1-Trac E-Diff 3 F1-Trac is a traction control system that derives directly from The vehicle is equipped with an electronic differential, working on Ferrari's expertise in F1 vehicles. the rear axle, which continually performs a variable check on the F1-Trac is faster and more accurate than traditional control locking between the two axle shafts. systems and is capable of delaying and minimising engine torque The electronic differential system, integrated with F1-Trac traction adjustments as required in order to ensure the desired trajectory. control, is capable of improving: The system estimates the maximum available grip in advance, by - performance; continuously monitoring the relative wheel speed and using an - directional stability of the vehicle; auto-adaptive operating logic. Comparing this information with - active safety even when close to grip limit; the vehicle dynamics model stored in the control system, F1-Trac optimises the vehicle behaviour by controlling engine torque - driving comfort and handling. delivery. The system is based on the analysis and forecast of vehicle performance in all possible conditions. This is done by continually Important note monitoring the pressure of the clutch actuator on the differential. The input signals are the dynamic parameters of the vehicle that the F1-Trac does not work when the Manettino is set to CT OFF control system translates into a torque difference between the two and ESC OFF driving modes. driving wheels. On bends, the electronic differential can: The main feature that distinguishes the F1-Trac system from a - stabilise the vehicle when the accelerator pedal is released by traditional traction control system lies in its ability to estimate grip locking the rear axle; level accurately which allows the driver to make full use of the vehicle's performance driving potential. - control vehicle dynamics by locking the differential according to lateral acceleration and vehicle speed; The F1-Trac system guarantees: - maximise vehicle stability and, at the same time, acceleration on - maximum traction when coming out of bends; bends by locking the differential according to lateral acceleration, - driving stability and ease even under extreme driving conditions; speed, engaged gear and torque produced by the engine. - driving comfort. To obtain these results, the electronic differential system interacts On this vehicle, integration of the F1-Trac and E-Diff 3 systems with the F1-Trac, ESC and ABS systems, F1 gearbox and ensures maximum performance and stability. suspension damping control. 74 Safety

EPB - Electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. Always apply the parking brake when the vehicle is parked. The parking brake is applied and released by pulling the relative lever B on the dashboard to the left of the steering wheel. With the The vehicle should be blocked. If this is not the case, please ignition key turned to II, the relative indicator on the instrument contact the Ferrari Service Network. panel (see page 121) lights up to indicate when the parking brake is engaged. Autopark Function Pull the lever B while holding the brake pedal depressed to release The EPB Autopark function automatically activates the electric 3 the parking brake. If the ignition key is turned to II, the indicator parking brake when the engine is switched off. At each Key-on, the extinguishes once the parking brake is completely released. Autopark function is always active by default: this means that the The electric parking brake may be used as an emergency brake driver does not need to apply the parking brake when the engine is when the vehicle is in motion. If this is the case, the system acts on switched off. all four wheels until button B is released by communicating with If necessary, the function may be temporarily disabled before the ESP system which prevents locking. switching off the engine by pressing the AUTO PARK button C: the message “PARK OFF” is displayed for 5 seconds on the left hand TFT display. In this case, after the engine is switched off, the parking brake must be engaged manually by pulling the lever B. To re-enable automatic EPB engagement at the next key-off, press the button C again; the message “PARK ON” is displayed for 5 seconds on the left hand TFT display. “Automatic Vehicle Holding” AVH function The Automatic Vehicle Holding function of the electric parking C brake ensures optimised release when moving off from a standstill: B after engine start, the system uses the service brakes to hold the vehicle instead of the parking brake shoes. Safety 75

Tyre temperature and pressure monitoring Warning system (TPMS) (optional) On request, the vehicle can be equipped with a system that The TPMS warns the driver that the tyre pressure has measures the tyre pressure and temperature using special sensors decreased. However, this does NOT exempt the driver from fitted inside the wheel rims next to the air valve. These sensors periodically checking that the tyres are inflated to the indicated transmit a signal that is received by the antennas on the car body, pressure. behind the gravel guards, that are connected to the ECU. In addition, the system does NOT warn the driver of damage to the tyres by external agents. Important note Displaying messages on the left TFT display The system may be momentarily affected by radioelectrical interference from devices that use similar wavelengths. By using the commands on the left TFT display (see page 96), the driver can access the TYRES screen page which displays the vehicle The ECU processes this information and transmits data on tyre symbol with the pressure and temperature values of each tyre as pressure and temperature and any system errors to the instrument shown in example 1. panel. The signal transmitted by the ECU activates symbols on the left TFT display (see page 96) with two priority levels: a soft warning (SW) if the pressure loss is 0.2 bar more than the rated pressure and a hard warning (HW) if it is 0.5 bar more or there is a dynamic decrease of over 0.2 bar/min. The TPMS can be calibrated using the special menu item in the left TFT display (see page 98). Important note System calibration using the special menu item on the left TFT display is necessary after replacement or inflation of a tyre or tyres. 1 76 Safety

If an event occurs that needs to be displayed as a symbol and/or The screen page is displayed for 20 seconds and then the screen special message when the TYRES screen page is displayed, the page that was previously displayed reappears. If the failure screen page is minimised as shown in example 2. For further persists, the screen page shown above (example 3 or 4) will be information, refer to the “Fault displaying logic” paragraph on automatically displayed for 20 seconds the next time the engine is page 113. started. The driver can call up the TYRES screen page at any time to Low pressure display which tyres have low pressure (example 5). Regardless of the type of screen page on the left TFT display, when the instrument panel receives the signal from the tyre pressure ECU that the pressure level of one or more tyres is below the alarm threshold, the screen page shown in example 3 (for a warning related to only one tyre) or example 4 (for a warning related to 3 several tyres) appears immediately. Check tyre Check tyre Catalysts temp. pressure pressure too high Engine performance limited 2 3 4 5 Safety 77

Occasionally, the system may not detect which wheel signals The screen page is displayed for 20 seconds and then the screen a failure. If this is the case, then only the message “Check tyre page that was previously displayed reappears whereas the warning pressure” will be displayed as shown in example 6. light remains on in fixed mode. If normal tyres are used, the failure follows the same display logic Tyre puncture as the other priority level 0 faults (see the “Fault displaying logic” Regardless of the type of screen page on the left TFT display, when paragraph on page 113) until the situation is corrected and the the instrument panel receives the signal from the tyre pressure system is recalibrated. ECU that the pressure level of one or more tyres is below the If the vehicle is fitted with Run Flat tyres, the maximum distance alarm threshold, the screen page shown in example 7 (warning allowed in a “tyre puncture” state is 100 km (62 mi). The not to proceed for vehicles fitted with normal tyres) or example 8 instrument panel will calculate the residual tyre life and will (warning to proceed at a maximum speed of 80 km/h (50 mph) redisplay the screen page shown in example 8 after 50 km (31 mi). for vehicles fitted with Run Flat tyres) appears immediately. At the The same screen page (warning not to exceed a maximum speed same time, a warning light comes on on the panel (see page 119) in of 80 km/h) is displayed if the vehicle exceeds 80 km/h (50 mph). fixed mode. Once the distance of 100 km (62 mi) has been exceeded, the panel displays the screen page shown in example 7 (warning not to proceed). If you call up the TYRES screen page, you can identify the punctured tyre at any time (example 9). Check tyre pressure Low tyre Low tyre pressure pressure Do not Max speed proceed 80 km/h 6 7 8 9 78 Safety

If another tyre is punctured, the instrument panel will update the Occasionally, the system may not detect which wheel signals a number of km (mi) which can still be driven according to the failure. If this is the case, the screen page shown in example 12 (for distance driven after the previous puncture and will display the vehicles fitted with normal tyres) or example 13 (for vehicles fitted screen page shown in example 10. with Run Flat tyres) will be displayed. While priority level 0 (normal tyre puncture) or priority level 2 The symbol and message are displayed for 20 seconds and then the (Run Flat tyre puncture with maximum speed limit not exceeded screen page that was previously displayed reappears whereas the and tyres still usable) faults are being displayed, the driver can warning light remains on in fixed mode. press the OK button with “ESCAPE” function (see page 113): the If the vehicle is fitted with Run Flat tyres, the instrument panel will screen page disappears whereas the warning light on the panel calculate the residual tyre life and will redisplay the screen page remains on in fixed mode. As above, the TYRES screen page can be called up at any time to display which tyres are punctured (example 11). shown in example 13 after 50 km (31 mi). The same screen page (warning not to exceed a maximum speed of 80 km/h) is displayed if the vehicle exceeds 80 km/h (50 mph). Once a distance of 3 100 km (62 mi) has been exceeded, the panel displays the screen page shown in example 12 (warning not to proceed). Low tyre Low tyre Low tyre pressure pressure pressure Max speed Do not Max speed 80 km/h proceed 80 km/h 10 11 12 13 Safety 79

System not calibrated When the Menu item is displayed and the subsequent calibration If the system has not been calibrated or one or more tyres have accepted, the screen page shown in example 15 appears for been replaced, the symbol and message shown in example 14 will 5 seconds. be displayed. At the same time, the warning light on the instrument panel (see page 119) will flash for 90 seconds. Warning When the display cycle ends (20 seconds), the symbol and message Before calibrating the system, make sure that the tyre pressure disappear and the screen page that was previously displayed corresponds to the indicated pressure values (see page 28). If reappears whereas the warning light remains on until the system this is not the case, the TPMS may issue wrong low pressure has been calibrated. indications. The TPMS can be calibrated using the special menu item in the left TFT display with the ignition key in position II and the engine off. To calibrate the TPMS, call up the MENU screen page on the left TFT display (see page 98) with the ignition key in position II and the engine off. Once the MENU screen page appears, select the items “Car setup”, “Calibr. TPMS”. Display setup Date/Hour TPMS Calibration activated Language/M.U. not calibrated Execute Car setup calibration Dimming 14 15 80 Safety

TPMS failure At the same time, a warning light comes on on the panel (see The screen page shown in example 16 is displayed in the following page 119) in flashing mode for 90 seconds. The warning light then circumstances: remains on in fixed mode until the situation is corrected. - malfunction in the circuit and/or wiring connecting the ECU The TYRES screen page cannot be called up by the driver. - signal is not received by one or more sensors due to a faulty, System not active broken or flat battery For a few seconds at key-on, if the TPMS has been deactivated by a - fault in the TPMS ECU. diagnostic tool, the screen page in example 18 is displayed. At the same time, a warning light comes on on the panel (see At the same time, a warning light comes on on the panel (see 3 page 119) in flashing mode for 90 seconds. The warning light then page 119) in flashing mode for 90 seconds. The warning light then remains on in fixed mode until the situation is corrected. remains on in fixed mode until the situation is corrected. The TYRES screen page cannot be called up by the driver. The TYRES screen page cannot be called up by the driver. System temporarily not active The screen page shown in example 17 is displayed in the following circumstances: - overheating of sensors - during calibration (the TPMS ECU does not recognise the sensors) - radio frequency that interferes with the wheel sensor signal. TPMS failure TPMS TPMS inactive temporarily inactive 16 17 18 Safety 81

Doors ................................................................... 84 Engine compartment lid......................................... 86 Luggage compartment lid ...................................... 87 Ignition switch ....................................................... 89 Fuel filler flap and neck .......................................... 90 Power windows ..................................................... 92 Instruments and gauges ......................................... 94 Controls on the steering wheel ............................. 126 Lighting............................................................... 132 Retractable hard top ........................................... 138 Driving the vehicle ............................................... 143 EPB - Electric parking brake ................................. 161 Park Lock ............................................................ 163 Launch Control ................................................... 164 Stop&Start system (optional) ............................... 167 Seat adjustment .................................................. 175 Air conditioning and heating system ..................... 183 Passenger compartment accessories ..................... 187

4 ABOUT YOUR VEHICLE

Doors Locking and opening the doors from the inside When a door is opened or closed, the window automatically moves down by approximately 2 centimetres / 0.8 inches (to its “target Warning position”) to avoid colliding with the upper weather strip. Always carefully check manually that the doors have been When the door is closed, the window automatically moves up until closed properly to prevent them from opening while driving. it reaches the “upper limit”. Both doors can be locked by activating/deactivating the “LOCK/ Opening from the outside UNLOCK” B button on the roof panel. To lock the doors, press Using the remote control, deactivate the alarm and the central door button B; when the door lock is activated, the light on button B locking system, or turn the key in the lock to deactivate the central comes on. To deactivate the door lock, press button B until the door locking system. light goes out. To open the door, pull handle A: the window will move down to its A function that automatically inserts the door lock when the vehicle “target position”. When the door is closed, the window will move is moving at a speed of 20 km/h (12 mph) or over can be activated up until it meets the upper limit. on the “Car setup” menu on the left TFT display of the instrument panel (see page 98). B � C 84 About your Vehicle

If you pull handle C to open the door, the window will move down to its target position. When the door is closed, it will move up until it meets its upper limit. If handle C is lifted without opening the door, the window will move down to its target position and stop and if the door is not opened after 2 seconds, the window will move back up until it meets the upper limit. Therefore, to open the door, release handle C and pull it again. When the opening handle is operated, both doors are unlocked. 4 About your Vehicle 85

Engine compartment lid Closing Opening Lower the lid until it is closed and press down near the lock until you hear it click in place. Pull release lever D on the driver-side internal sill. Lift the engine compartment lid. The lid is held open by two gas Warning struts E. Always check manually that the engine compartment lid has The engine compartment lid can also be opened with the ignition been closed properly to prevent it from opening while driving. key at off. E E D 86 About your Vehicle

Luggage compartment lid Important note Opening After removing the battery from the vehicle or disconnecting The luggage compartment lid can also be opened with the ignition it from the electrical system, a door lock/unlock cycle must be key at off. performed using the buttons on the key when reconnecting so Push release button F on the left edge of the driver-side floor or that the release button F resumes normal operation (electronic press button G on the ignition key for more than 2 seconds. system self-acquisition procedure). Stand in front of the vehicle, slightly lift the lid and pull the retaining lever H to lift it completely. The lid is held open by two gas struts L. The luggage compartment is illuminated by an internal light that comes on automatically when the luggage compartment lid is opened. 4 G F H About your Vehicle 87

Closing Emergency Opening Lower the lid until it is closed and press down near the lock until If the luggage compartment lid opening button does not work, you hear it click in place. there is a string for manual emergency opening underneath the dashboard to the left of the steering wheel as shown by the arrow in the figure. Warning Always check that the luggage compartment lid has been closed properly to prevent it from opening while driving. L L 88 About your Vehicle

Ignition switch Warning The ignition key can be turned to 2 positions: Position 0 - Stop Never remove the key when the vehicle is moving! Engine off, key removable. The steering wheel will lock with the first turn of the steering wheel. When the key is even only partially extracted, the steering column is locked. Always remember to remove the key from the ignition when you get out of the vehicle! The hazard warning lights and parking lights can be activated. Never leave people who are more subject to injury unattended To facilitate steering wheel release, turn the steering wheel slightly in the vehicle. clockwise or counterclockwise while turning the ignition key. Position II - Start Key lock When the key is turned to this position (key-on) the signals If more than 20 seconds elapse after turning the key to position 0, generated by the vehicle systems are checked. The left and right TFT displays are activated on the instrument panel and when the signals have been checked, the gearbox display the key lock device must be released to remove the key: press button K and remove the key at the same time. 4 comes on (see page 122). K II 0 About your Vehicle 89

Fuel filler flap and neck Emergency Opening If the opening button does not work, the fuel filler flap can be opened manually by pulling the cable P on the right-hand side of Warning the engine compartment. Always turn off the engine during refuelling. Do not smoke or use naked flames when refuelling. There is a risk of fire. The following can be harmful for your health: - fuel coming into contact with your skin - inhaling fuel vapours. Opening To open the fuel filler flap, press button M on the left edge of the driver-side floor. Closing To close the fuel filler flap, push it until it clicks in place. M P 90 About your Vehicle

Capless filler neck This vehicle has a capless filler neck for fuelling. This system allows Warning you to refuel by opening the fuel filler flap and simply placing the Place the nozzle in the filler neck carefully to avoid damaging nozzle in the filler neck without having to unscrew a cap and screw the device seal. it up again. Do not try to open the external flap of the filler neck by pushing Two flaps placed in series, both with airtight seals, act as a cap. it with your fingers or lever it open using unsuitable tools (e.g. The external flap is locked by a series of “teeth” and the only way screwdrivers). This may damage the external flap mechanism to open the external flap correctly is by inserting a petrol pump and the seal. nozzle. Warning Do not overfill the fuel tank: this may cause the fuel to leak out. After fuelling, wait for about 5 seconds before slowly removing the nozzle from the filler neck: in this way, the last drops of fuel will flow into the tank and will not drip onto the vehicle. 4 Warning Do not place funnels or portable container nozzles in the filler neck. If you need to refuel from a portable fuel container, use only the funnel supplied in the tool bag (see page 192) that releases the automatic closing device. About your Vehicle 91

Power windows Passenger-side power window The power windows can only be used with the ignition key in Press button B to move the window up or down. position II. Only manual operation is possible (partial opening) to raise the Driver-side power window window: when button B is released, the window stops at the position reached. Press button A to move the window up or down. To lower the window, automatic operation is also possible (full This allows manual operation (partial opening/closing) or opening): if the button is pressed at length (over 0.3 seconds) automatic operation (complete opening/closing): press button A automatic window operation is activated. The window will only and quickly release to activate manual operation; if the button is stop when it reaches the end of its travel or by pressing the button pressed at length (over 0.3 seconds), automatic window operation again. is activated. The window will only stop when it reaches the end of its travel or by pressing the button again. When the door is open, the window moves down to its “target position”; this is to prevent the window from colliding with the upper weather strip when it is closed. Warning Improper use of the power windows can be dangerous. Before use, always check that people and objects are at a safe distance. Pay particular attention during automatic operation of the passenger-side power window. To protect the passengers remaining in the car against accidental B activation of the power windows, always remove the key from the ignition. A 92 About your Vehicle

BackLite rear screen Important note Pull or press button C to move the BackLite rear screen up or down respectively. Given the special design of the vehicle, rain or washing processes may cause water to collect in area Z shown in the figure. Important note The vehicle has drain holes S for discharging the water that has While the hard top is being opened, the BackLite rear screen is collected. automatically raised until it reaches the optimum height for the Depending on the amount of water collected, it may take several windbreak function. From this position, it can be partially raised minutes for it to discharge. or completely lowered. The limit imposed on raising the rear screen prevents positions that create troublesome turbulence. To raise or lower the rear screen, once the hard top has fully Warning opened (see page 140), pull or press button C. Important note Do not park the vehicle facing downhill. If there is heavy rain and the drain holes S get clogged, water 4 may collect in the compartment behind the rear screen. If this happens, do not open the rear screen and contact the Ferrari When you park the vehicle and want to leave it in coupé Service Network to get the drain holes cleaned. configuration, make sure that the rear screen is closed. S S C Z About your Vehicle 93

Instruments and gauges 6 5 2 5 3 7 1 5 4 5 94 About your Vehicle

1 Left TFT display 2 Rev counter 3 Right TFT display 4 Gear display 4 5 Warning lights on the panel 6 Manettino status 7 Fuel level About your Vehicle 95

Left TFT display MAIN screen page Located on the instrument panel, it performs the following If you press the MAIN button, you activate the MAIN screen page functions: which can be used to access the four screen page groups SETUP, VDA, TRIP and STATUS. These groups contain the following screen - displays the control parameters pages: - displays general information while driving SETUP (pressing the UP button) - displays fault warnings MENU screen page The driver can interact with the system by selecting the configuration and setting the parameters using the controls on the STATUS (pressing the DOWN button) dashboard to the left of the steering wheel. SPORT screen page The display is activated and set by pressing the MAIN (A), VDA (B), SPORT 2 screen page OK (C) and UP, DOWN, LEFT, RIGHT (D) buttons. TYRES screen page (only if TPMS is present) VDA (pressing the LEFT button) Chronometer screen page Vehicle status screen page Manettino status screen page TRIP (pressing the RIGHT button) TRIP A screen page TRIP B screen page B A C D 96 About your Vehicle

Press the RIGHT and LEFT buttons to sequentially switch between Every screen page consists of four display areas: screen pages in a group. Press RIGHT to go to the next screen page A - selected driving mode (Manettino position), windscreen wiper (for example, in the STATUS group from SPORT to SPORT 2) status, outside temperature and “Warning: danger of ice” icon and press LEFT to go to the previous screen page. Press the RIGHT B - display of virtual control gauges, parking sensor screen page, button after the last screen page to go back to the first screen page display of abnormal events/warnings (message text and special and press the LEFT button after the first screen page to go back to symbol, when available), display of brightness adjustment the last screen page. function When a screen page is called up, it remains on the display until you C - total or trip odometer (TRIP A or B), range decide to select another one. D - fuel level gauge, area for minimised symbol for faults that do not have a specific warning light on the panel (see page 111), speed repetition. 4 About your Vehicle 97

Display setting and configuration of vehicle parameters Navigation within the menu is on several levels; the first level offers a list of items through which the following parameters can be set or the following information can be displayed: Warning - Dimming: display dimming setting Display setting and parameter configuration should be - Display setup: display setting performed when the vehicle is stationary - Date/Hour: date and time setting - Language/M.U.: language and units of measurement setting MENU screen page - Car setup: vehicle parameter configuration Display setting and configuration of the various vehicle parameters - Calibr. TPMS: TPMS calibration (only if present) is possible using the MENU screen page (the only screen page in - Service: information on scheduled maintenance. the SETUP group) that can be directly called up by pressing the UP button when the MAIN screen page is activated. These items are the main menu functions. To scroll through the list of items, press the UP and DOWN buttons; to select the required function, press and quickly release the OK button or the RIGHT button. Display setup M.U. Distance Date/Hour M.U. Temp. Language/M.U. Language Car setup M.U. Pressure Dimming 98 About your Vehicle

Once the function has been selected, the individual subfunctions or Adjusting brightness parameters that can be activated are displayed. To select them, use The brightness of the two TFT displays on the instrument panel the UP and DOWN buttons and press and quickly release the OK can be adjusted by selecting the special item on the MENU screen (or RIGHT) button to activate a subsection or activate the selected page or by using directly the UP and DOWN buttons when the parameter. MENU screen page is not displayed and when the chronometer is To go back to a previous level in the menu hold down the OK off if the Chronometer screen page is displayed. button, press the LEFT button or select the BACK item which is The first time one of the two buttons is pressed, the screen page normally in the list of subfunctions. If no operation is performed is displayed. The next time the buttons are pressed, the brightness for at least 10 seconds, the first menu level reappears on the can be adjusted. display. The adjustment made, which can be activated even when the vehicle is moving, can be seen immediately and does not affect the brightness of the warning lights on the panel. The screen page disappears when the OK button is pressed or automatically if it is not used for 5 seconds and is replaced by the screen page that was previously displayed. 4 DIMMING About your Vehicle 99

Fuel level gauge In limited cruising range conditions, the information on driving range in km is replaced by the words “Limited cruising range”. The fuel level gauge is always displayed in area D of the display (see page 97). The gauge has 9 yellow bars that gradually “turn off” as the fuel level drops. When the second bar goes off, the first bar turns red until fuel runs out. In “Fuel level low” condition, a warning light comes on on the panel (see page 116) and a special symbol and message are displayed for 10 seconds together with information on driving range in km. If the condition that has generated it persists, this signal is repeated every 8 km (5 mi). Fuel level Fuel level Low low Limited Range cruising 86 km range 100 About your Vehicle

SPORT screen page SPORT 2 screen page The SPORT screen page displays the following virtual gauges: The SPORT 2 screen page displays the following virtual gauges: - Engine coolant temperature - Engine oil pressure - Engine oil temperature. - Voltmeter. If the SPORT screen page is being displayed and an event occurs If the SPORT 2 screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the that needs to be displayed as a symbol and/or special message, the virtual gauges are minimised. For further information, refer to the virtual gauges are minimised. For further information, refer to the “Fault displaying logic” paragraph on page 113. “Fault displaying logic” paragraph on page 113. 4 About your Vehicle 101

TYRES screen page (only if TPMS is present) VDA (Vehicle Dynamic Assistance) screen page group The TYRES screen page, available only if there is a TPMS (tyre In addition to its chronometer function, the Vehicle Dynamic pressure and temperature monitoring system), displays the vehicle Assistance (VDA) screen page group provides a valid support for symbol and indicates the pressure and temperature values for each assessing vehicle status when on the track and can be used to tyre. intuitively understand the most suitable conditions for performance If the TYRES screen page is being displayed and an event occurs driving. The VDA group, which is recalled by pressing the LEFT that needs to be displayed as a symbol and/or special message, button with the MAIN screen page displayed or directly by pressing the screen page is minimised. For further information, refer to the the VDA button with any screen page displayed, consists of the “Fault displaying logic” paragraph on page 113. “Chronometer”, “Vehicle status” and “Manettino status” screen pages. The “Vehicle status” screen page functions are only available when the “Manettino” driving mode control switch (see page 127) is set to RACE, CT OFF or ESC OFF, positions developed especially when using the vehicle on track; however, if the Manettino is set to WET or SPORT mode, the “Vehicle status” screen page is displayed along with the message “VDA not available in WET - SPORT”. VDA not available in WET - SPORT 102 About your Vehicle

Chronometer screen page During display of the event/malfunction, the chronometer remains The “Chronometer” screen page is used to time laps and memorise active. lap time if the vehicle is used on track. The screen page displays the Each time the key is turned to on, the chronometer is reset whereas following information: the last valid Best Lap and Last Lap information is memorised. Current Lap indicates the time elapsed since the start of the chronometer Chronometer operating logic LAP TIME / Best The chronometer is controlled using the OK, UP and DOWN indicates the time required to complete the last best lap buttons that perform the following functions: LAP TIME / Last - Pressing and quickly releasing the OK button: indicates the time required to complete the last lap when the chronometer is off, starts the Current Lap chronometer TOP SPEED / Best indicates the maximum speed reached when the chronometer is on, resets and restarts the Current Lap and updates the information on previous laps (end of lap/start of TOP SPEED / Last indicates the maximum speed reached in the last lap. next lap) - Pressing and quickly releasing the UP or DOWN button: 4 If the “Chronometer” screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special when the chronometer is on, stops the chronometer and updates message, the screen page is minimised. For further information, information on previous laps refer to the “Fault displaying logic” paragraph on page 113. when the chronometer is off, displays the screen page for adjusting display brightness - Holding down the UP or DOWN button: when the chronometer is on or off, resets the chronometer and information on previous laps. LAP TIME Note that during display of an event/malfunction, pressing and Best: 1:11:00 Current LAP Last: 1:14:40 quickly releasing the OK button interrupts the event/malfunction 1:12:10 TOP SPEED display cycle (“ESCAPE” function), without affecting the Best: 247 Km/h chronometer. Last: 230 Km/h About your Vehicle 103

Vehicle status screen page OVER The “Vehicle status” screen page, which is directly called up by One or more systems have reached an overheating condition pressing the VDA button or by pressing the LEFT button when the that may affect vehicle dynamics. Slowing down is therefore MAIN screen page is displayed, is intended to help the user bring recommended to restore these systems to optimum conditions of the vehicle to optimum performance when driving on high grip use. surfaces. This is made possible by an algorithm that determines the thermal state of the main vehicle subsystems (tyres, brakes and engine) in relation to the dynamics of various parameters (lateral acceleration, speed, etc.). The status of the vehicle is displayed concisely using three levels which are blue, green and red: WARMUP Function not WARMUP GOavailable OVER Warm-up stage for components and self-acquisition of control systems; during this stage, the vehicle should be driven so that it is taken to optimum conditions of use. GO The vehicle has completed the warm-up stage: all its subsystems have reached optimum conditions of use for performance driving. Function not WARMUP GOavailable OVER Function not WARMUP GOavailable OVER 104 About your Vehicle

After each start, the ESC stability and traction control system If one or more signals related to the performance parameters used compensates for the tyre rolling radius and detects the spare to calculate the thermal state of the subsystems (lateral acceleration, wheel. While this procedure is being performed, the Vehicle Status speed, etc.) are not valid, the Vehicle Status screen page indicates screen page indicates to the driver that system self-acquisition is in to the driver that the function is not available by displaying the progress by displaying the message “ESC autolearning”. message “Function not available”. Warning Use of the vehicle on race tracks: after each start, cover the first straight stretch of the track (at least 500 meters / 0.3 mi) at a constant speed so that the ESC stability and traction control system can calculate exactly the grip available and the rolling radius of the tyres (the calculation is reset every time the engine stops). If this rule is not followed, system performance may be reduced. 4 ESC Autolearning Function not available About your Vehicle 105

Manettino status screen page If one of the other two VDA screen pages is displayed The “Manettino status” screen page displays a list of parameters (“Chronometer ” or “Vehicle Status”), the “Manettino Status” which can be configured using the “Manettino” driving mode screen page is displayed in timed mode for 3 seconds when the control switch (see page 96) and indicates the configuration each position of the Manettino is changed so that the driver is informed one assumes in a specific driving mode. of the new status that the systems are in. After 3 seconds, the screen page that was previously displayed reappears. The systems involved are the following: The “Manettino status” screen page is also automatically displayed - F1-Trac: traction control in timed mode at key-on if one of the other two VDA screen pages - E-Diff: electronic differential was displayed at the previous key-off and the Manettino was in a - F1-DC: dual clutch F1 gearbox different position from the current one. - ESC: stability and traction control - ABS: anti-lock braking system Important note - SCM: magnetorheologically controlled suspension. If there is a Manettino failure, the “Manettino Status” screen page cannot be displayed or recalled. VEHICLE DYNAMICS F1-Trac E-Diff F1-DC ESC ABS SCM 106 About your Vehicle

TRIP A and TRIP B screen pages The TRIP A or TRIP B screen page displays the following information: - Maximum speed - Average speed - Travel distance - Travel time - Range. If the TRIP A or TRIP B screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the screen page is minimised. For further information, 4 refer to the “Fault displaying logic” paragraph on page 113. TRIP A Mon 16 Nov Maximum speed 263 Km/h Average speed 124 Km/h Travel distance 292.8 Km Travel time 03:36 h:m Range 204 Km About your Vehicle 107

“Warning: danger of ice” message When the minimum limit of 30 km/h (17 mph) is reached, press To warn the driver of the presence of ice on the road if the outside the DOWN button again to deactivate the function or press the UP temperature is 3 °C (38 °F) or below, the “snow” symbol and the button after reaching the maximum speed of 250 km/h (155 mph). “warning: danger of ice” message are displayed for 10 seconds in The function is normally deactivated (OFF). the top right of the display. When the set limit is exceeded, the driver is informed in the When they are displayed, the symbol and message appear instead of following way: the outside temperature; after 10 seconds, the outside temperature The symbol showing the set limit and a “Speed limit exceeded” is displayed again and the “snow” symbol appears next to it as long message appear in the top right of the display for 10 seconds as the outside temperature remains 6 °C (43 °F) or below. accompanied by an acoustic signal. Once the warning cycle has ended, the message disappears whereas the symbol continues to be Speed limit setting and “Speed limit exceeded” message displayed next to the outside temperature until the speed decreases The MENU screen page can be used to set a speed limit in the to 5 km/h (3 mph) below the set limit. range 30 - 250 km/h (17 - 155 mph) with 5 km/h (3 mph) steps which sends a message to the driver when exceeded. To set the speed limit, call up the MENU screen page by pressing the UP button when the MAIN screen page is activated. Select “Car setup” and “Speed limit”. To set the value, use the UP and DOWN buttons. Warning: 120 Speed limit danger of ice exceeded 108 About your Vehicle

Parking sensors (optional) The rear parking sensors are automatically activated when the key is in position II and reverse gear is engaged. When the rear sensors To help the driver when parking, the vehicle can be fitted on are activated, an acoustic signal warns the driver that the system has request with four sensors in the rear bumper (rear parking been activated. If the vehicle is also equipped with front sensors, sensors), or four sensors in the front and rear bumpers (front and these can be activated or deactivated by pressing the relative button rear parking sensors). on the roof panel (see page 137). Warning “Stop and Go” function The system will only operate correctly if the sensors on the The “Stop & Go” function, available on vehicles with front and bumpers are free of mud, dirt, snow or ice. rear parking sensors, automatically activates the front sensors when vehicle speed is 10 km/h (6 mph) or below. This system has been designed to assist the driver in certain traffic conditions When approaching obstacles in front of or behind the vehicle, (e.g. tailbacks) and signals when the minimum distance is reached the parking sensors inform the driver of the distance between the between the vehicle and the vehicle in front. vehicle and the obstacle by way of acoustic signals, which become more frequent as the obstacle approaches, and visual signals in To activate or deactivate the system, call up the MENU screen page, select the items “Car setup”, “Parking sensor”, and select one of the 4 area B of the left TFT display (see page 97). By supplementing the driver's direct visual information with that provided by the system two options, “STOP&GO ON” and “STOP&GO OFF”. acoustic signals and visual warnings, potential collisions can be avoided when parking. Indication of obstacles The parking sensor system emits acoustic signals as soon as an Warning obstacle is detected which become more frequent as the obstacle approaches. The acoustic signal stops immediately if the distance It is the driver, however, who holds full responsibility for from the obstacle increases whereas the tone cycle remains parking manoeuvres and other potentially dangerous situations. constant if the measured distance from the central sensors remains The system has only been designed as an aid during parking unchanged. manoeuvres since it detects obstacles that are outside the The vehicle symbol and sensor detection zones appear on the driver's field of vision. left TFT display: these zones indicate which part of the vehicle Use of the sensors therefore does not mean that the driver can is approaching an obstacle (if front or rear and if left, right or be less careful and attentive and not watch out for persons and central) and the distance from the obstacle (maximum, medium or obstacles during parking manoeuvres. minimum). About your Vehicle 109

If an obstacle is detected at maximum distance in the central front If an obstacle is detected at minimum distance in the central front part, it will be displayed as shown below (green). part, it will be displayed as shown below (red). If an obstacle is detected at medium distance in the central front The maximum, medium and minimum distances between the part, it will be displayed as shown below (orange). vehicle and an obstacle, represented graphically by the colours green, orange and red, are different for the front and rear parking sensors: Rear sensors: Maximum distance (green): 80 to 70 cm - 31 to 28 in. (150 to 70 cm - 59 to 28 in. in central zone) Medium distance (orange): 69 to 41 cm (27 to 16 in.) Minimum distance (red): 40 to 0 cm (16 to 0 in.) Front sensors: Maximum distance (green): 73 to 53 cm - 29 to 21 in. (110 to 70 cm - 43 to 28 in. in central zone) Medium distance (orange): 52 to 31 cm (20 to 12 in.) Minimum distance (red): 30 to 0 cm (12 to 0 in.) 110 About your Vehicle

If the front sensors are deactivated or not present, the display does If the parking sensor system symbols are being displayed and an not show the symbols in the front. In the same way, if front sensors event occurs that needs to be displayed as an icon and/or special are fitted and the rear ones are not activated, the display only message, the symbol is moved from the centre of the display to the shows the symbols in the front. If all the sensors are activated, the right as shown below. system can give several pieces of information at the same time: if an obstacle is detected at a maximum distance in the front central Cleaning the sensors part and at a minimum distance in the rear right part, it will be When cleaning the sensors, be very careful not to scratch or displayed as shown below. damage them and avoid using dry, rough or hard cloths. The sensors must be washed with clean water and car shampoo added if necessary. In car washes that use steam jet or high pressure water cleaning equipment, quickly clean the sensors keeping the nozzle at a distance of at least 10 cm (4 in.). For the repainting of bumpers or retouching the paintwork in the sensor area, contact the Ferrari Service Network. If paint is applied incorrectly, it may prevent the parking sensors from working properly. 4 Catalysts temp. too high Engine performance limited About your Vehicle 111

Indication of parking sensor failure The system ECU checks all the components each time the reverse Important note gear is engaged. If at least one parking sensor is faulty, the special The signals sent by the sensors may also be affected by damage symbol (see page 120) is displayed on the left TFT display together to the sensors caused by dirt, snow or ice on the sensors or with the message “Parking sensor failure. Warning! Possible by ultrasound systems (e.g. pneumatic brakes on lorries or obstacles” accompanied by an acoustic signal. pneumatic drills) in the vicinity. Important note The sensors are able to detect obstacles with reasonably large, Warning even surfaces (e.g.: poles with diameters of over 60 mm (2.4 in.), However, the driver has full responsibility for parking walls, barriers, trees). Detection is not optimum with obstacles manoeuvres and in other potentially dangerous situations. with sharp projections or uneven surfaces. The system has only been designed as an aid during parking manoeuvres, since it detects obstacles that are outside the driver's range of visibility. Important note The sensors are therefore not a substitute for the driver's care During parking manoeuvres, always take the utmost care since and attention when parking and checking for the presence of obstacles may be located above or below the sensors. persons or objects. Important note Objects placed close to the rear part of the vehicle are not always detected by the system and may therefore damage the vehicle or be damaged themselves. 112 About your Vehicle

Fault display If the fault is resolved within 20 seconds, it remains displayed and the warning light remains lit for 2 seconds. Fault displaying logic When a fault occurs, the corresponding warning light (if present) “ESCAPE” function comes on on the panel whereas a description of the fault (if Displaying a fault on the screen can be interrupted by pressing and available) and the relevant symbol (if available) are displayed on quickly releasing the OK button with “ESCAPE” function. When the left TFT display. The message appears on the display at the the OK button is pressed, the screen page that was displayed prior same time as the warning light (if present) comes on and the main to the event reappears. If the fault does not have a special warning screen page that is displayed at that moment is minimised. light on the panel, the symbol remains minimised in area D until The fault remains on the display for 20 seconds. When the display the cause of malfunctioning has been resolved. cycle ends, if the fault does not have a special warning light on the panel, the symbol remains minimised in area D of the display (see page 97) until the cause of malfunctioning has been resolved. In area B the main screen page is displayed in “maximum” size. When the display cycle ends, if the fault has a special warning 4 light on the panel, the screen page that was displayed prior to the event reappears and the symbol is not minimised in area D. The warning light remains on until the cause of malfunctioning has been resolved. Catalysts temp. too high Engine performance limited About your Vehicle 113

Fault priority levels Indication of failure of turn indicators and running lights The simultaneous display of several faults follows a logic that A failure of the running lights (front and/or rear) and turn depends on the priority level assigned to it: indicators (front and/or rear) is indicated in the same way as other Priority level 0 - Extremely critical fault faults but the vehicle symbol with the faulty running light or turn indicator indicated in red is displayed together with a description Priority level 1 - Critical fault of the failure instead of the “External lights failure” symbol (see Priority level 2 - Non-critical fault. page 117). When the display cycle ends or the OK button with When several fault events occur at the same time, faults with “ESCAPE” function has been pressed, the “External lights failure” priority level 0 are displayed first, followed by priority level 1 symbol is minimised. and then priority level 2. The information on the various faults is displayed in turn for 5 seconds each. In any case, the total display time for each fault is never less than 20 seconds. If a fault message with priority level 1 or 2 is being displayed, the priority level 2 message is only displayed once the priority level 1 message has been displayed for at least 2 seconds. If, on the other hand, another new priority level 0 fault occurs, this is displayed immediately. Lamp Failure 114 About your Vehicle

“Doors, engine or luggage compartment lid open” function display If one or more doors or the engine and/or luggage compartment lid are open, the vehicle symbol appears on the display and indicates which doors or lids are open together with a special message. If the vehicle is in motion, an acoustic signal is also emitted. When the display cycle ends or the OK button with “ESCAPE” function has been pressed, the special symbol is minimised (see page 119). 4 Doors open About your Vehicle 115

List of left TFT display symbols and warning lights Alternator failure on the panel red If there is a fault in the recharging system (priority red level 1). TFT Warning Description and warnings Low windscreen washer fluid level light Indicates a low level of washer fluid in the Alarm system failure orange windscreen washer tank (priority level 2). Indicates a fault in the alarm system (priority level 1). Oil temperature orange The system is not programmed (priority level 2). Failure and system not programmed (priority level 1). Indicates that the oil temperature is too high red (priority level 0). red Contact the Ferrari Service Network. Turn off the engine and contact the Ferrari Alarm system failure (priority level 2). Service Network. Break-in attempted (priority level 2). Adaptive headlights failure orange Symbol and warning light in flashing mode Fuel reserve orange orange indicate there is a failure in the adaptive headlight system (priority level 2). Indicates that the fuel level is too low (priority orange level 2). Windscreen wiper motor failure orange Indicates a windscreen wiper motor failure (priority Battery conditioner connected orange level 2). When the instrument panel is on, it indicates that the red battery conditioner is connected (priority level 0). Engine coolant temperature Indicates that the engine coolant temperature is too Inertia switch red high (priority level 0). red Indicates activation of the inertia switch following orange an accident and the resulting cut-out of the fuel Turn off the engine and contact the Ferrari supply (priority level 0). Service Network. The hazard warning lights are also automatically activated. 116 About your Vehicle

Oil pressure External lights failure red Indicates that the engine oil pressure is too low Indicates a system fault or blowing of a bulb in the red (priority level 0). orange running, turn indicator or rear fog lights (priority level 2). Turn off the engine and contact the Ferrari Service Network. Number plate lights failure Indicates a system failure or blowing of the number A flashing warning light indicates an engine oil plate light bulb (priority level 2). red pressure sensor failure (priority level 2). orange Engine diagnostic system (EOBD) failure Rear fog lights When the rear fog lights are turned on. orange While the engine is running, it indicates a fault in orange orange the emission control system and in the ignition/ injection system (priority level 0). Turn off the engine and contact the Ferrari Twilight sensor failure Indicates a twilight sensor failure (priority level 2). 4 orange Service Network. High beams After turning the ignition key to position II, it remains on for a self-check for a few seconds after When the high beams are turned on. blue the engine has started. When the high beams are used to flash. Running lights Right turn indicator green When the running lights or low beams are turned on. When the right turn indicators are activated. green Stop lights failure Indicates a system failure or blowing of the STOP Left turn indicator orange light bulb (priority level 2). When the left turn indicators are activated. green About your Vehicle 117

Hazard warning lights ABS green The left and right hand turn indicator lights flash Indicates an ABS system failure (priority level 1). simultaneously if the hazard warning lights are orange orange activated. The standard braking system is still functioning. Catalytic converter temperature Contact the Ferrari Service Network. Indicates that the catalytic converter temperature is ESC off red too high: stop the vehicle (priority level 0). Symbol and warning light indicate that the ESC Contact the Ferrari Service Network. orange system has been deactivated (priority level 1). orange The symbol is displayed for 5 seconds together with Indicates that the catalytic converter temperature is the “ESC off” message. very high: reduce speed until the symbol goes out (priority level 1). ESC system failure orange Indicates a fault in the ESC system (priority level 1). Indicates a failure of the catalytic converter orange temperature sensor (priority level 0). orange Warning Checking the engine oil level Indicates a low engine oil level (priority level 0). Stop the vehicle and avoid sharp braking. Stop driving and contact the Ferrari Service orange Network immediately. Seat heating Indicates that heated seat function is enabled (remains displayed for 5 seconds). Warning orange However, the vehicle can be moved to clear Power steering failure the road by adjusting the speed to the road Indicates that the power steering system is conditions and type of road. orange inefficient (priority level 2). ESC system activation (flashing warning light) Contact the Ferrari Service Network. Indicates that the ESC system has been activated orange (priority level 1). 118 About your Vehicle

CCM brake discs worn Airbag system failure Indicates that the carbon ceramic brake discs are Indicates a system failure (priority level 0). worn (priority level 2). red red With the warning light in flashing mode, it indicates orange that the airbag test cycle has not been completed Contact the Ferrari Service Network. (priority level 0). TPMS Contact the Ferrari Service Network. Indicates a puncture in one or more standard tyres orange Driver-side seat belt not fastened orange (priority level 0) or Run Flat tyres (priority level 2). With the warning light in flashing mode for a Indicates that the driver-side seat belt has not been maximum of 90 seconds after which it remains on red fastened (priority level 0) together with an acoustic in fixed mode, it indicates: signal lasting 90 sec. A failure in the TPMS (priority level 2). 4 Passenger-side seat belt not fastened TPMS temporarily inactive (priority level 2). Indicates that the passenger-side seat belt is not TPMS inactive (priority level 2). red red fastened (priority level 0). TPMS not calibrated (priority level 2). Speed limit exceeded Doors/front and rear lids open Indicates that the speed set by the driver has The symbol, which is minimised, indicates that one been exceeded (priority level 2), the figure shown red or more doors and/or lids are open. indicates the set speed. E-Diff system failure E-DIFF Indicates an electronic differential failure (priority level 1). orange E-DIFF red About your Vehicle 119

Brake malfunction Front Lift system failure Indicates that the brake fluid level is low (priority Indicates a Front Lift system failure (priority red level 0). level 1). red orange Indicates an EPB (electric parking brake) failure (priority level 0). Generic failure Indicates an overhaul of the Parking Brake system Indicates an airbag warning light failure (priority (priority level 0). orange level 2). Indicates a Manettino failure (priority level 1). Indicates a failure in the electronic system (priority level 2). red Indicates an EBD system failure (priority level 0). red TPMS Indicates that calibration of the TPMS has been orange green activated. Rain sensor failure Indicates a rain sensor failure (priority level 2). Brake pad wear Indicates excessive wear of the brake pads (priority orange red level 2). red Suspension control system failure Parking sensor failure Indicates a malfunction in the suspension control system (priority level 2). Indicates that the parking sensor system is faulty orange orange (for vehicles equipped with this system) (priority Contact the Ferrari Service Network. level 2). Scheduled Maintenance (Service) Front Lift system status Indicates the Scheduled Maintenance deadline. When on in fixed mode, it indicates that the Front green Lift system is activated (vehicle raised). green When on in flashing mode, it indicates that the AVH system Front Lift system is being operated (activation or Indicates an AVH system failure (priority level 0). deactivation cycle). orange 120 About your Vehicle

Ice hazard Electronic rev counter Indicates that the outside temperature is 3 °C The electronic rev counter indicates the engine RPM. The numbers (38 °F) or lower, highlighting the risk of icy road on the dial multiplied by 1000 correspond to the engine RPM in surfaces. one minute. Drive carefully in these conditions and slow down Avoid engine speed rates in the red sector. since tyre grip is significantly reduced. There is a space to the bottom right of the rev counter for the display which gives information on dual clutch transmission (DCT). Warning In this condition, activate the “WET” driving Important note mode. With a white or yellow rev counter dial face, the backlight is not activated in daytime conditions (with running lights switched Parking brake off, or with running lights on but daytime light conditions red Indicates that the parking brake is applied. detected by twilight sensor) to ensure better visibility of the instrument. 4 Gearbox failure Indicates a system failure (priority level 1). red red Contact the Ferrari Service Network. About your Vehicle 121

Engine RPM LED on steering wheel (optional) Gearbox display The five LEDs on the steering wheel rim (available on request) The display which gives information on dual clutch transmission light up in sequence and inform the driver that the maximum (DCT) is found to the bottom right of the rev counter; with the engine RPM has been reached for gearshifting. When 5500 RPM is ignition key in position II, it displays the following information: reached, the first LED comes on; the others come on in sequence - gear engaged; when 6,250, 7,000, 7,750 and 8,920 RPM are reached. - indication of “Automatic gearbox” mode; The LEDS on the steering wheel can be deactivated using the - indication of “Auto easy exit” mode; MENU screen page on the left TFT display (see page 98): call up the MENU screen page, select the items “Car setup” and “RPM on - indication of gearbox in “Parking” mode; steer” and then select OFF. To reactivate the function, select ON. - indication of Launch Control activated; - indication of AVH system activated. Important note Information on the gearbox is useful in all operating conditions. 122 About your Vehicle

Gear engaged Indication of “Automatic gearbox” mode The gearbox display shows the number or letter indicating the When the gearbox is used in “automatic” mode (see page 149), the engaged gear in the centre. word “auto” appears in the bottom of the gearbox display together N Neutral with the number or letter indicating the engaged gear. R Reverse Indication of “Auto easy exit” mode 1 1 gear st When the gearbox is used in “Auto easy exit” mode (see page 149), the word “auto” appears in the bottom of the display together with 2 2 gear nd a small “arrow” pointing downwards on the left. 3 3rd gear Indication of gearbox in “Parking” mode 4 etc. When the gearbox is in “Parking” mode, i.e. the Park Lock gearbox When the key is turned to off, the display remains on for at least locking device is activated (see page 163), the letter “P” appears in 3 seconds and displays the engaged gear. If the control panel reads the centre of the gearbox display. N (Neutral), the letter N is displayed and a buzzer will sound. 4 About your Vehicle 123

Indication of Launch Control activated Right TFT display When the gearbox is used in “manual” mode and the Launch Located on the instrument panel, it performs the following Control function is requested by pressing the special button on functions: the centre console (see page 164), the word “launch” appears in the bottom of the gearbox display. The word remains while the - it displays the speedometer function is activated. - it displays infotainment system information Indication of AVH system activated - it displays the rear parking camera (if present). In certain circumstances, when the AVH system is activated (see page 162), the word “HOLD” appears in the top of the gearbox The driver can interact with the system by selecting the display. configuration and setting the parameters using the controls on the dashboard to the right of the steering wheel. Holding button A down switches the infotainment system on and off. Holding button B down allows you to select whether to display infotainment system information or display the speedometer. A B 124 About your Vehicle

Infotainment system “Speedometer” screen page The infotainment system includes the following functions: The “Speedometer” screen page indicates the speed by displaying a CD/DVD player with charger mounted in glove compartment, virtual analogue speedometer. MW/LW/FM radio, 30 GB hard disk drive, USB connection, iPod® connector (optional), satellite navigator (optional), Bluetooth “Digital speed” screen page connectivity, voice recognition. The “Digital speed” screen page indicates the speed in digital form. As well as using the commands on the dashboard to the right of the steering wheel, the infotainment system can be controlled using Important note buttons behind the steering wheel. The speedometer is always also displayed in digital form in For further information on the infotainment system, please refer to area D of the left TFT display (speed repetition, see page 97). the instruction manual enclosed with the vehicle documents. Speedometer display Time display The speedometer can be displayed on the right TFT display in “Speedometer” or “Digital speed” mode. By selecting the special item on the MENU screen page of the left TFT display, you can activate/deactivate the time display in the top 4 To select the desired display mode, call up the MENU screen page right of the “Speedometer” and “Digital speed” screen page. The on the left TFT display (see page 98) and select the items “Display time is displayed approximately 10 seconds after key-on. setup”, “Display right”. 126 About your Vehicle 125

“Rear Parking Camera” screen page (optional) Controls on the steering wheel If the vehicle has a rear parking camera (optional), the “Rear Parking Camera” screen page is automatically displayed on the right Start button TFT display when reverse gear is engaged. This screen page, which continues to be displayed until reverse gear is disengaged, shows Press the ENGINE START button A to start the engine. When the the field of vision of the camera mounted on the rear bumper and engine has started, release the ENGINE START button. helps the driver when parking. Do not hold the ENGINE START button down for a long time. The image is overlaid with static green, yellow and red grids For more information on starting the engine, see page 145. indicating the distance of obstacles within the camera's field of vision. the area within the red grid represents a zone from 0 to 60 cm (0-24 in.), the yellow grid represents a zone from 60 to 120 cm (24-47 in.) and the green grid represents a zone from 120 to 200 cm (47-79 in.). A B 126 About your Vehicle

“Manettino” driving mode control switch SPORT mode The driver can select the desired driving mode by using the This is the ideal setting for vehicle performance recommended for “Manettino” B. everyday driving in medium- to high-grip conditions. The driving mode selected does not exempt the driver from RACE mode complying with the rules of safe driving. This mode offers maximum performance and stability in high grip conditions and is particularly suitable when using the vehicle on Important note track. In the event of a failure of one of the onboard systems, signalled CT OFF mode by the special symbol on the left TFT display, the Manettino” When this mode is selected, the F1-Trac traction control system is moves to a “recovery” position, but still allows the vehicle to be disabled whereas stability control remains active. This mode is used driven. In these cases, contact the Ferrari Service Network. on the race track in high grip conditions. ESC OFF mode Driving modes that can be selected with “Manettino” This mode allows the driver complete freedom and control of the vehicle for track use in high-grip conditions. 4 WET mode No electronic system other than the E-Diff controls vehicle stability. This is the maximum safety driving mode. Recommended in low grip conditions. Warning In low- to medium-grip conditions (e.g. wet, icy, sandy roads), do not deactivate the ESC system. Important note For further information on the driving modes that can be selected, refer to the paragraph “Driving using the driving mode control switch” on page 155. About your Vehicle 127

Suspension damping delink button Horn control By pressing button C on the left of the steering wheel, the driver The horn sounds when you press on the horn symbol on the can choose to separate the suspension damping control from the steering wheel rim. logic of the “Manettino” driving mode control switch. For further information, see page 159. C 128 About your Vehicle

“UP” shift paddle Windscreen washer/wiper lever Pull the right-hand UP paddle towards the steering wheel to shift gears up. Important note The windscreen wipers and washer only work when the ignition “DOWN” shift paddle key is in position II. Pull the left-hand DOWN paddle towards the steering wheel to shift gears down. The windscreen wipers and washer are operated using lever A on the steering wheel: the lever must be pressed towards the dashboard or pulled back according to the function you require. The windscreen wipers have 4 different speeds: OFF Windscreen wipers stationary. AUTO The rain sensor adjusts the windscreen wiper timing to the 1 intensity of the rain. Slow continuous operation. 4 2 Fast continuous operation. DOWN UP A About your Vehicle 129

With the wipers stationary (OFF), quickly pressing lever A towards the dashboard activates the windscreen wipers in AUTO speed. Important note With the wipers on, quickly pressing the lever towards the Windscreen wiper operating is always guaranteed even if dashboard increases windscreen wiper speed (from AUTO to 1, there is an electronic system failure. If there is a failure, the from 1 to 2). windscreen wipers can be activated by pressing lever A and With the wipers set to AUTO or OFF, holding the lever towards the deactivated by pulling it back. dashboard activates maximum speed (2). With speed 1 or 2, on the If there is a particularly serious failure, operating may not be other hand, the windscreen wipers stop. automatically maintained: if this is the case, the windscreen With the wipers on, quickly pulling lever A back decreases wipers can be kept activated by holding down lever A. windscreen wipers speed (from 2 to 1, from 1 to AUTO, from AUTO to OFF). With the wipers stationary, quickly pulling the lever back activates Windscreen washer fast temporary operating of the wipers (antipanic wiping). To activate the windscreen washer, keep lever A pulled. When the The windscreen wiper speed is indicated in the top of the left TFT lever is released, the windscreen wiper returns to the preset speed. display as shown in the figure below. Warning Do not start the windscreen washer during the cold months until the windscreen has warmed up. If it has not warmed up, the liquid could freeze on the glass and interfere with visibility. A Headlight washer The headlight washer is activated automatically when the windscreen washer is operated and the low beams are on. The headlight washer and windscreen washer share the same fluid tank and a low fluid level is indicated by the relative symbol on the left TFT display. 130 About your Vehicle

Rain sensor Rain sensor failure The rain sensor automatically adjusts the windscreen wiper timing If there is a rain sensor failure, indicated by a special symbol on to the intensity of the rain. The system is activated by moving the the left TFT display (see page 118) while the windscreen wiper windscreen wiper to AUTO. is set to AUTO, the wipers will be set to intermittent operation When operating automatically, the wiper speed ranges from a with one wipe every 1 second approximately. If this is the case, we minimum intermittent setting (one wipe every 5 seconds approx.) recommend that you deactivate the rain sensor and turn on the when the windscreen is damp to fast continuous operation in heavy wipers, if necessary, in continuous mode. rain. Important note Important note If this occurs, contact the Ferrari Service Network as soon as The rain sensor function is deactivated by turning the ignition possible. key to position 0 and leaving the windscreen wiper in position 4 AUTO. To reactivate the system at the next key-on, set the wipers to AUTO by quickly pressing the lever A towards the dashboard. Warning Before cleaning the front windscreen (for example in service stations) make sure the rain sensor is deactivated or that the key is in position 0. The rain sensor must be deactivated also when washing the vehicle by hand or in automatic car washes. In case of ice or snow on the front windscreen, do not activate the rain sensor to avoid damaging the wiper motor and/or blades. About your Vehicle 131

Lighting High beams The external lights and turn indicators only work when the ignition To turn on the high beams when the light switch A is set to , key is in position II. pull back lever B on the steering wheel. The external lights can be switched on and off manually or When the high beams are on, the relative warning light on the automatically, depending on the ambient light. instrument panel comes on. Then push lever B towards the dashboard or pull it back to turn off Light switch the high beams and turn on the low beams. The switch A, on the dashboard to the left of the steering wheel, can be set to five different positions: Flashing the headlights 0 Lights off The headlights can be flashed by pushing the left-hand lever B Running and number plate lights on (*) towards the dashboard. Flashing also occurs with lights off if the ignition key is set to II. Low beams on (*) The high beams are used for flashing. Parking lights AUT Automatic operation of the external lights according to ambient light. (*) The relative warning light on the instrument panel comes on. B A 132 About your Vehicle

Important note Important note Follow the Road Regulations of the country you are travelling in The high beams can only be activated manually by pulling back for using the high beams. the left-hand lever B. Important note Parking lights The parking lights work only with the ignition key in position 0 or If the high beam control is activated, the high beams will with the key removed. turn on every time the lights are activated automatically. We recommend therefore that you turn them off every time the They are activated by turning the light switch A to position . twilight sensor deactivates the external lights. When the parking lights are on, the warning light illuminates on the instrument panel . When the parking lights are on, hold down one of the two turn indicators C buttons on the steering wheel (see page 134) for Warning If there is fog during the day, the running lights and low beams 4 more than 0.5 seconds to turn on the partial parking lights on the will not be turned on automatically. The driver must always be corresponding side; press the same turn indicator again for more ready to turn on the lights manually and also the rear fog lights, than 0.5 seconds to go back to full parking lights. if necessary. When the partial parking lights are on (on only one side of the vehicle), the running light warning light turns off whereas the vehicle symbol indicating which parking light is on (left or right) is Important note displayed on the left TFT display for 10 seconds. After automatic activation of the external lights, it will always When the light switch A is turned to AUT and the ignition key is in be possible to turn on the rear fog lights manually. When position II, the running lights, low beams and number plate lights the external lights are deactivated automatically, the rear fog turn on and off automatically according to the ambient light. lights are also turned off (if active) automatically. Therefore, if necessary, the driver will have to turn on the rear fog lights manually upon the next automatic activation. About your Vehicle 133

Day lights Warning The LEDS on the headlights serve as front turn indicators and day The driver is always responsible for turning on the external lights. To activate or deactivate the day running lights, call up the lights, depending on the ambient light and in compliance with MENU screen page on the left TFT display, select the items “Car the regulations in force in the country of use. The automatic setup”, “Day lights” and select ON to activate the function and OFF system for turning on and off the external lights must be to deactivate it. considered an aid for the driver. If necessary, turn the lights on and off manually. Turn indicators Quickly press the left indicator or right indicator button C on the steering wheel to switch on the relevant turn indicator. Twilight sensor The relative warning light or on the instrument panel The twilight sensor is comprised of a global sensor which measures comes on. the ambient light upwards. The turn indicator goes off when the steering wheel is realigned. In the event of sensor failure, the system switches on low beams Holding down one of the two C buttons (for more than and running lights, regardless of the daylight conditions; a failure 0.3 seconds) temporarily switches on the relevant turn indicator: it message will appear on the instrument panel display. is switched off after 3 flashes (“lane change” function). The failure indication will be displayed as long as the light switch is turned to AUT. If this occurs, we recommend that you deactivate the automatic system and turn on the external lights manually if necessary. Important note If this occurs, contact the Ferrari Service Network as soon as possible. C C 134 About your Vehicle

Rear fog lights Hazard warning lights The rear fog lights are turned on only if the high beams or low Press button F to turn on the hazard warning lights. All the turn beams are on when button D is pressed; the relevant warning indicators will start blinking intermittently; these lights will operate light E on the instrument panel comes on to indicate that they have with the ignition key in any position. been turned on. When the lights are on, the relative warning lights on the instrument panel and the button flash. Important note To turn them off, press the button again. Use the rear fog lights only in poor visibility conditions. 4 D E F About your Vehicle 135

“Follow me home” function AFS2 adaptive headlights (optional) With the “Follow me home” function, the low beams stay lit for a The AFS2 adaptive headlight system (available on request) enables preset period of time once the engine has been turned off and light synchronous movement of the left and right front beams (high up the area around the vehicle to help the driver and passengers and low) and has been designed to illuminate the road better and see their way in the dark. reduce areas of shadow in the vehicle's trajectory. The function can be manually activated by pressing the high The headlights' swivel angle, which ranges from 8° inwards and 15° beam/flashing lever B (see page 132) when the ignition key is outwards, is defined by the steering angle. in position 0 or removed, within 3 minutes of switching off the The AFS2 system also uses a “Dynamic Levelling” device that engine (time that is reduced to 30 seconds if the driver-side door directs the light beam vertically when accelerating and braking by is opened). Each time lever B is pressed, the period of time that the moving the headlights up to 1.9° upwards when braking and up to low beams remain on increases by 30 seconds up to a maximum of 1° downwards when accelerating. 210 seconds. The adaptive headlight system deactivates its corrective action Each time lever B is pressed, the message “Follow me” appears on when driving round bends at low speed. the left TFT display followed by the preset period of time that the low beams remain on. 136 About your Vehicle

Dome light Roof panel controls When the doors are closed, the dome light D on the roof can be turned on or off using the switch E. Door lock/unlock Switches F and G turn the driver-side and passenger-side spotlights Both doors can be locked by activating/deactivating the “LOCK/ on and off. UNLOCK” H button. For further information, see page 84. The dome light activates automatically in the following conditions: - when a door is opened, for approx. 3 minutes Deactivating the anti-lift alarm - when all the doors are closed and the key is in position 0, for Press button L to deactivate the anti-lift alarm system. For further approx. 10 seconds information, see page 18. - when the key is removed, for approx. 10 seconds - when the doors are unlocked, for approx. 10 seconds Front parking sensors (optional) - when the inertia switch is activated, for approx. 15 minutes. On vehicles fitted with front and rear parking sensors, the front The dome light deactivates automatically in the following conditions: - after the preset activation time expires parking sensors are activated/deactivated by pressing button M. When the front parking sensors are activated, the light on the 4 button comes on. - when the doors are closed and the key is in position II - when the doors are locked - when the inertia switch is reactivated. M F E G H L D About your Vehicle 137

Retractable hard top Warning The retractable hard top system consists of the following main moving parts: Only operate the hard top when the vehicle is stationary and on level ground. - a front element - a rear element - a cover Warning - a Backlite rear screen. The hard top should only be opened or closed when passengers Opening and closing is actuated by a hydraulic system, driven by are correctly seated. a pump and controlled by a number of sensors that check every opening and closing phase. Warning Warning Do not place or leave items in the hard top compartment V. Avoid opening and closing the hard top repeatedly. Prolonged use of the hydraulic system causes it to overheat and disables Warning it temporarily. The message “Roof operation inhibited-System overheating” appears on the TFT display. After a few minutes, Do not install accessories (ski racks, luggage racks, etc.) on the normal operation is resumed. hard top. V Roof operation inhibited System overheating 138 About your Vehicle

The conditions required for opening and closing the retractable Warning hard top are as follows: Before operating the hard top and while it is in motion, always - the ignition key must be in position II; ensure that all children, persons and objects are a safe distance away from the moving parts. In the event of danger, release the Important note hard top switch: all movement will stop immediately. We recommend operating the hard top with the engine running. Warning - the engine compartment lid must be closed properly; While the hard top is in motion, never place your hands, fingers - the battery voltage must not be below 11 volts; or objects on the moving parts or on the windscreen cross - the hydraulic system must not be overheated. member. If one or more conditions are not met, the hard top cannot be 4 opened or closed and a message appears on the left TFT display. Warning Important note DO NOT open the retractable hard top when the outside temperature is below -10 °C (14 °F). Check that there is sufficient vertical clearance to open the hard top. Warning Before operating the hard top, make sure that the engine compartment lid has been closed correctly. If the engine compartment lid is open, a vehicle symbol appears on the left TFT display that indicates that the lid is open together with a special message. Important note We recommend closing the hard top when parking. About your Vehicle 139

Opening the hard top Important note Important note While the hard top is being opened, you cannot operate the side windows and the BackLite rear screen. Before opening the hard top, ensure that it is dry to prevent water entering the passenger compartment or hard top compartment. Once the opening cycle has been completed, the message “Roof open” is displayed on the left TFT display accompanied by an acoustic signal. Pull switch A on the centre console and keep it pulled until the hard top is fully open: the operation in progress is indicated by the To raise the side windows completely, keep switch A pulled for message “Roof opening” on the left TFT display. approximately 2 seconds. When the hard top opens, the following operations take place: - the side windows and BackLite rear screen are fully lowered Warning - the hard top compartment cover opens Do not reverse the opening or closing direction when opening - the hard top parts are positioned in the hard top compartment or closing the hard top. - the hard top compartment cover closes Always complete the cycle until the acoustic signal is emitted. - the BackLite rear screen is raised until it reaches the set height - the side windows are raised. A Roof open Roof opening 140 About your Vehicle

Closing the hard top Press switch A on the centre console and keep it pressed until the Important note hard top is fully closed: the operation in progress is indicated by While the hard top is being closed, you cannot operate the side the message “Roof closing” on the left TFT display. windows and the BackLite rear screen. When the hard top closes, the following operations take place: - the hard top compartment cover opens Once the closing cycle has been completed, the message “Roof - the side windows and BackLite rear screen are fully lowered closed” is displayed on the left TFT display accompanied by an acoustic signal. - the two parts of the hard top come out of the hard top compartment and the front part fits onto the windscreen cross To raise the side windows completely, keep switch A pressed for member approximately 2 seconds. - the hard top compartment cover closes - the Backlit rear screen is raised Warning - the side windows are raised. Do not reverse the opening or closing direction when opening or closing the hard top. 4 Always complete the cycle until the acoustic signal is emitted. A Roof closed About your Vehicle 141

Interrupting the hard top opening/closing cycle Indication of hard top operating system failure If button A is released before the hard top has been completely If there is a hard top operating system failure, it is indicated by opened or closed, it remains in a stand-by position and the message a special symbol and the message “Roof failure” on the left TFT “Complete roof cycle” appears on the left TFT display until the display. opening or closing cycle is reactivated. Warning Warning If there is a hard top operating system failure, contact the Do not drive until hard top opening or closing has been fully Ferrari Service Network. completed. If the hard top is still in standby position after a few minutes, an acoustic signal will prompt you to complete the operation. Warning Try not to interrupt the hard top opening/closing cycle. If you have to interrupt the opening/closing cycle, do not leave the hard top in stand-by position for longer than 4 minutes. Roof failure 142 About your Vehicle

Driving the vehicle Before a trip Preliminary checks Running-in Check the following at regular intervals and always before long The latest manufacturing techniques have allowed us to achieve trips: high precision and accuracy levels in the construction and assembly - tyre pressure and condition of components. Nonetheless, the vehicle movable parts undergo a - levels of fluids and lubricants settling process, basically during the first hours of operation. - condition of the windscreen wiper blades - proper functioning of the warning lights and external lights. Engine and transmission Avoid exceeding 5,000 RPM for the first 1,000 km (620 mi). Important note After starting, do not exceed 4,000 RPM until the engine has warmed up (oil temperature: 65-70 °C / 149-158 °F). In any case, it is advisable to perform these checks at least every Do not let the engine run at a constantly high speed for a prolonged time. 1000 km (620 mi) and always comply with the maintenance schedule. 4 Warning It is also advisable to: - clean the glass covers of the external lights and all the glass BEFORE YOU DRIVE surfaces Check that the seat belts are fastened - properly adjust the mirrors, steering wheel, seats and seat belts. Check that the doors are closed Refilling Check that the seat is properly adjusted Check the rear-view mirror adjustment (central and sides). Warning Use unleaded fuel only! Using leaded fuel would permanently damage the catalytic converters. For specifications and quantities of lubricants and fluids, refer to the “Refilling” table on page 31. About your Vehicle 143

Starting and driving the vehicle System start-up Important note After turning the ignition key to position II (key-on), both TFT BEFORE YOU DRIVE displays are activated on the instrument panel and system diagnosis If the warning light A does not turn off after diagnosis, is performed. During diagnosis, which lasts 5 seconds, a check is indicating a fault in the gearbox also shown by the symbol and performed on the warning lights on the panel and the presence of special message on the left TFT display (see page 121), contact any faults is checked. the Ferrari Service Network. If diagnosis detects any errors, they are only displayed once the 5 seconds required for the check have elapsed. The cases listed below are an exception and errors are displayed as soon as the key is turned to on, even during diagnosis: - Low engine oil pressure (see page 117) - Inertia switch triggered (see page 116) - Semi-automatic gearbox safety warnings - EPB deactivation warning (see page 161). If the next scheduled maintenance deadline is approaching, each time the key is turned to on, information on scheduled maintenance is automatically displayed after diagnosis. For further information, refer to the “Maintenance Schedule” paragraph on page 226. Finally, each time the key is turned to on, the message for activation of the alarm when an intrusion has been attempted (see page 19) is also displayed (after diagnosis). Once the system check has been completed, the gearbox display is activated and the letter “P” (Parking) or “N” (Neutral) will be A displayed. 144 About your Vehicle

Starting the engine Important note Before starting the engine, make sure that the alarm system and all The vehicle is equipped with an electro-hydraulically controlled electrical devices with high power absorption are turned off. gearbox system operated by means of paddles on the steering • Make sure that the electric parking brake is applied and that the wheel. doors are closed. The default setting for the DCT gearbox is always “Automatic” • Hold the brake pedal down when starting the engine. mode (see page 149). Every time the vehicle is started, the DCT gearbox is in “Auto Warning easy exit” mode (see page 149) unless the vehicle was in “Automatic” mode when the engine was turned off. Do not press the accelerator pedal. To exit the “Auto easy exit” mode operate the UP and DOWN paddles (while the vehicle is moving) or press the AUTO button • Turn the ignition key to position II and wait for the gearbox display to come on. on the centre console. • Press the ENGINE START button (see page 126) and release it as soon as the engine starts. 4 Important note Do not hold the ENGINE START button down for a long time. Immediately release the UP and DOWN paddles or button R If the engine does not start, turn the key back to position 0 and after the gearbox display shows that the gear has been engaged; wait for the gear display to go off before retrying. a prolonged manoeuvre would cause the gearbox failure warning light to turn on (see page 121) and triggering of the Warning buzzer. Hold the brake pedal down while starting the engine. Important note None of the gears can be engaged if the luggage compartment lid is open or not properly closed. When the vehicle is stationary, with the driver-side door open or not properly closed and the brake pedal released, the system disengages the gear engaged after approximately two seconds. About your Vehicle 145

If the engine fails to start after several attempts, check for one of the following causes: Warning • insufficient speed of the starter motor (flat battery) If the UP and DOWN paddles are not working, the message • ignition device faulty “Depress brake pedal and press LAUNCH to engage gear” will • electrical contacts faulty appear on the left TFT display; you can therefore engage the gear by pressing the LAUNCH button on the centre console (see • fuel pump fuses blown. page 164) and the brake pedal. Warming up the engine In these cases, the “Launch Control” function is not available. If the engaged gear was R, the LAUNCH button must be pressed Do not run the engine at high speed until the engine oil temperature twice to engage 1st gear. has reached at least 65-70 °C (149-158 °F), approximately. Starting the vehicle Important note With the engine started, the vehicle stationary and the brake pedal pressed, pull the right-hand “UP” paddle towards the steering When reverse is selected, an acoustic safety signal beeps wheel to engage 1st gear. intermittently as long as “R” is engaged. Release the brake pedal and press the accelerator to start off. With the engine running and the vehicle stationary, you can change If the system automatically selects 2nd gear when attempting to directly from 1st or 2nd gear to “R” (reverse) by pressing R on the shift from R to 1st gear, this indicates that 1st gear has jammed. centre console and from reverse to 1st by moving the UP paddle. Therefore, this is not a malfunction, as it falls within the system operating logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has jammed. During prolonged stops with the engine running, it is advisable to keep the gearshift in “N”. R Important note If you allow the vehicle to move forward in N, when UP or DOWN is requested, a gear will be engaged that corresponds to the speed of the vehicle. 146 About your Vehicle

UP-shifting DOWN-shifting Use the right-hand UP paddle without releasing the accelerator Use the left-hand DOWN paddle without releasing the accelerator pedal. pedal. An UP-shift request is not accepted when engagement of the A DOWN-shift request is not accepted if engagement of the requested gear forces the engine to underrev or if an UP-shift is requested gear forces the engine beyond a certain RPM, depending already in progress because of engine overrevving. on the gear requested, or if a DOWN-shift is already in progress In any event, it is advisable to: because of engine underrevving. • Shift gears without releasing the accelerator pedal if pressed. In any event, it is advisable to: • Wait until gearshifting has been completed before requesting the • Shift gears without releasing the accelerator pedal if pressed. next shift, avoiding a rapid sequence of multiple requests. • If DOWN-shifting is requested to start overtaking which requires quick acceleration, press the accelerator pedal just before using UP-shifting due to overrevving the paddle. 4 The system “automatically” engages a higher gear if the accelerator • Wait until gearshifting has been completed before requesting the pedal is pressed and the engine approaches the “runaway speed rate” next shift, avoiding a rapid sequence of multiple requests. (overrevving). DOWN-shifting due to underrevving Important note • The system shifts down “automatically” if the engine goes below a minimum number of revs (1250 RPM). This will not occur when the system is in “RACE”, “CT OFF” and • The DOWN-shift request from the paddle is ignored if “ESC OFF” driving modes. gearshifting is already in progress due to engine underrevving. Sequential downshifting During deceleration, with the brake pedal pressed and the ABS system disabled, sequential downshifting can be performed by holding the left-hand “DOWN” paddle down. The sequential gearshifting request is accepted until the second gear is engaged. This system is only activated when the “Manettino” is set to SPORT, RACE, CT OFF or ESC OFF. About your Vehicle 147

“N” (Neutral) request With the engine running, pull both UP and DOWN paddles towards Warning the steering wheel at the same time without pressing the brake pedal Never leave the vehicle with the gearbox in “N”. Always make sure to request neutral “N”. that the letter “P” (Parking) appears on the gearbox display. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. Warning Stopping the vehicle Never leave the vehicle with the engine running. When the vehicle stops, the system automatically engages 1st gear unless Neutral has already been requested. Important note When the vehicle is stationary and the engine is running, hold the brake pedal down until ready to move off again. If the vehicle is not in Parking mode (the letter “P” must be displayed on the gearbox display), the key cannot be removed. Switching off the engine The engine can be switched off with the gearbox either in “N” or For information on the Park Lock, see page 163. with a gear engaged. After turning the ignition key from position II to position 0, the gearbox display will remain on for a few more seconds to display the engaged gear. If the gearbox is in “N” a buzzer will sound. Before switching off, the letter “P” is displayed on the gearbox display to inform the driver that the Park Lock has been activated. 148 About your Vehicle

“Automatic gearbox” mode “Auto easy exit” mode The “Automatic gearbox” mode is enabled/disabled by pressing the Every time the vehicle is started, the gearbox starts in “Auto easy AUTO C button on the centre console. When the “Automatic” mode exit” mode unless it was in “Automatic” mode when the engine was is enabled, the word “auto” appears on the gearbox display. To exit turned off. In this case, it remains in “Automatic” mode the next the “Automatic” mode, you must press the AUTO button until the time the engine is started. word “auto” on the gearbox display disappears. Activation is signalled by the word “auto” and an arrow in the When the “Automatic Gearbox” mode is enabled, the system will gearbox display. automatically UP-shift and DOWN-shift according to vehicle speed, In this mode, the system will automatically UP-shift and DOWN- engine revs and the torque/power request of the driver. shift according to vehicle speed, engine revs and the torque/power When you are in “Automatic” mode, you can however manually request of the driver. shift gears using the UP and DOWN paddles. The system remains To exit the “Auto easy exit” mode and go to “Manual” mode, in “Automatic” mode: this is indicated by the word “auto” that operate the UP or DOWN paddle (while the vehicle is moving) or remains on the gearbox display in flashing mode when the paddles press the AUTO button on the centre console. are used. When the vehicle is stationary, a “N”, 1st gear or “R”request will not If the “Automatic” gearbox mode is then requested by pressing the AUTO button, the system will apply all the characteristics of the 4 result in a change from “Automatic” to “Manual”. “Automatic” gearbox mode. Push start Warning C Push starting is not allowed. About your Vehicle 149

Safe driving While travelling For safe driving, it is essential that the driver be aware of the best - Caution is the number one rule for safe driving, which also means driving techniques suited to various circumstances. Always try to you should take other people’s behaviour into consideration. prevent dangerous situations by driving with caution. - Follow the Road Regulations in force in the country you are Before you drive driving in and always respect the speed limit. - Adjust the position of the seat, steering wheel and rear-view - Always make sure that the driver and passengers have their seat mirrors, in order to obtain the best driving position. belts fastened and that all children are travelling in suitable child - Adjust the backrest so that your chest is upright and your head is seats. as close to the headrest as possible. - Good personal physical conditions ensure you can drive long - Ensure that nothing (e.g. mat covers, etc.) is blocking the pedals. distances safely. - Check that the lights and headlights are working properly. - Ensure that any child restraint systems (e.g. child seats, cradles Warning etc.) are properly fixed on the passenger seat. Driving under the influence of drugs, some medicines - Your reflexes are quicker if you eat lightly before driving: avoid and alcohol is dangerous to yourself and others as well as heavy meals before a trip. contravening road regulations and legal norms. - Do not drink alcoholic drinks before and during the journey. Travelling without your seat belt fastened increases the risk At regular intervals, check the following: of serious injury and death in the event of a collision. Always fasten seat belts and use child seats, if present. - Tyre pressure and condition. Do not travel with objects lying on the floor, especially in front - Engine oil level. of the driver’s seat: in the event of braking, these could slide - Engine coolant level and system condition. under the pedals, making it impossible to brake or accelerate. - Brake fluid level. Additionally, ensure that any loose floor mats sit correctly. - Steering fluid level. Water, ice and salt spread on icy roads may deposit on the brake - Windscreen washer fluid level. discs and reduce the efficiency of the initial braking. 150 About your Vehicle

- Make regular stops to loosen up your limbs and refresh yourself, Driving in the rain and avoid driving for hours on end. Rain and wet roads can cause hazardous situations. - Keep a constant air circulation in the passenger compartment. All manoeuvres are more difficult on a wet road since tyres have - Never coast downhill with the engine off: in these conditions significantly less grip on the road. This means that the braking the engine brake, servo brake and power steering are inefficient, distances increase considerably and road-holding decreases. braking requires greater pressure on the pedal and steering will Below is some advice for driving in the rain: be harder. - Keep a greater safety distance between yourself and the other Driving at night vehicles and reduce your speed. When you are travelling at night, follow these fundamental rules: - When it is raining very hard, visibility is also reduced. In these - Reduce speed, particularly on dark roads. cases, to make yourself more visible to others, turn on the low - Driving conditions are more demanding at night, so take beams even during the day. particular care. - Drive through puddles at low speed to avoid losing control of the - If you start feeling tired or sleepy, stop immediately: to continue driving would be a risk for yourself and for others. Continue only vehicle (“aquaplaning”): if this occurs, grip the steering wheel firmly. 4 after you have had a rest. - At night, it is difficult to judge the speed of vehicles in front of Warning you as you can only see their taillights: keep at a greater safety If the road is wet, reduce your speed to avoid “aquaplaning” distance than you would during the day. (when the tyre no longer touches the road surface because the - Use the high beams only outside of urban areas and when you are side channels of the tyre tread are not capable of removing all sure that they will not disturb other drivers. the channelled water due to their particular shape or insufficient - Turn off the high beams when you see oncoming vehicles and use depth and a layer of water is placed between the road surface the low beams. and the tyre. The fluid pressure generated is so high that it - Keep the lights and headlights clean. supports the vehicle's weight making it virtually impossible for the driver to control the vehicle). - Watch out for animals crossing the road when travelling outside urban areas. About your Vehicle 151

- Use the ventilation system to demist the windscreen (see Driving on mountain roads page 184) and avoid visibility problems. Below is some advice for driving on steep mountain roads: - Periodically check the condition of the windscreen wiper blades. - To prevent the brakes from overheating when driving downhill, Driving in fog use the engine to brake by engaging a lower gear. Whenever possible, avoid travelling if there is thick fog. If you have - Never coast downhill or drive downhill with the engine off or to drive in misty conditions, or if there is thick fog or fog banks, in neutral, nor with the ignition key removed from the steering follow these rules: column. - Keep a moderate speed. - Drive at a moderate speeds and do not “cut” corners. - Turn on the low beams, also during the day, and use the rear fog - Remember that overtaking uphill is slower and requires a longer light. Avoid using the high beams. free stretch of road. If you are overtaken when driving uphill, ensure that the other vehicle can pass easily. Driving on snowy or icy roads Warning Below is some advice for driving in these conditions: On stretches where visibility is good, turn off the rear fog light, - Keep a very moderate speed. it may be annoying for the occupants of the vehicles behind you. - Keep a safe distance from the vehicles in front of you. - Fit snow tyres approved for the vehicle. - Remember that fog makes the road damp and therefore all - Given the poor grip, use the engine brake as much as possible manoeuvres are more difficult and braking distances are longer. and avoid sudden braking. - Keep a safe distance from the vehicle in front of you. - Avoid sudden acceleration and sharp changes in direction. - As far as possible, avoid suddenly changing speed and direction. - During the winter season, even apparently dry roads can have icy - As far as possible, avoid overtaking. sections. - In the event of an emergency stop, (e.g. failures, inability to Therefore, be careful when driving along stretches of road in the proceed due to poor visibility conditions, etc.) try to free the shade as there may be icy patches. main driving lane. Then turn on the hazard warning lights and, if possible, the low beams. On approaching another vehicle, sound the horn rhythmically. 152 About your Vehicle

Driving with the “ABS” braking system Power steering system The ABS system assists the driver as follows: The power steering system uses the power produced by the engine - It prevents the wheels from locking and skidding during to help the driver steer more precisely while exerting less force on emergency braking, particularly in low-grip conditions. the steering wheel. - It allows braking and changing direction at the same time. This feature is affected by the physical limits and lateral grip of the Important note tyres. Remember that power steering does not work when the engine - When the ABS is activated, you will feel a slight pulsing of the is switched off and more force is therefore needed when brake pedal during emergency braking or in low-grip conditions. steering. DO NOT release the pedal but continue to push it to give continuity to the braking action. - The ABS prevents the wheels from locking, but it does not Warning increase the physical limits of grip between the tyres and the road: keep a safe distance from the vehicles ahead and reduce speed before curves. Do not keep the steering wheel fully turned (locked position) to the right or the left for more than 15 seconds when the engine is running. This may damage the power steering system. 4 Important note If the power steering system is not working properly, as indicated by a symbol which appears on the left TFT display (see page 118), contact the Ferrari Service Network. About your Vehicle 153

Suspension damping control Level 1 (COMFORT) This vehicle uses latest generation MagneRide™ magnetorheological Slightly more flexible setting, optimised to better absorb road suspension, a system developed by Delphi and perfected by unevenness and provide a better grip on wet road surfaces Ferrari for continuous automatic damping control. (Manettino set to WET). By processing data received from the vehicle dynamics sensors and Level 2 (SPORT) sensors that detect bodyshell movements, the ECU interprets the Slightly more rigid adjustment optimised for sports-style driving driving conditions and the road surface and immediately adjusts and for high speed (with medium-high grip), without significantly suspension response by varying the control current of each shock affecting comfort (Manettino set to SPORT). absorber. Level 3 (RACE) These sensors allow the ECU to calculate the vehicle speed, vertical Even more rigid setting optimised for use on the race track and lateral acceleration, steering angle and instantaneous pressure (Manettino set to RACE, CT OFF, ESC OFF). in the braking system, and hence to control suspension damping. This system not only ensures an optimal compromise between racing-style performance (handling) and comfort, but is capable of emphasising either aspect by using the different adjustments available controlled by the “Manettino” driving mode control switch. Three different setting levels are available on this vehicle. 154 About your Vehicle

Driving using the driving mode control switch SPORT mode (“Manettino”) The “SPORT” mode is the best setting for daily road use. This mode is designed to ensure stability only in medium-high grip The driving mode control switch on the steering wheel allows the conditions. Suspension damping shifts to Level 2 and gearshifting driver to use the vehicle potential in a fast and intuitive way. is more racy. The ESC system also switches to a different level There are five modes available, which correspond to the grip offering you greater driving freedom. level (from low to high) and consequently to the level of driving If “SPORT” mode is selected, it is indicated on the left TFT display assistance required (from high to none). as shown below: WET mode “WET” mode ensures stability on dry as well as on wet roads. It is therefore recommended for low grip conditions (e.g. rain) and on slippery or extremely uneven roads, but also to enhance comfort during city driving. Suspension damping is optimised to provide the best possible absorption (Level 1) and the ESC system is at its 4 maximum level; the standard Bosch ASR system is activated instead of the F1-Trac function. If “WET” mode is selected, it is indicated on the left TFT display as shown below: About your Vehicle 155

RACE mode The “RACE” mode should be used on the race track. Gearshifting Warning favours the racing style of the vehicle whereas the ESC system Use of the vehicle on race tracks: after each start, cover the first shifts to Level 3 (engine power reductions are minimal) and the straight stretch of the track (at least 500 meters / 0.3 mi) at a suspension becomes even stiffer (Level 3). The performance ABS constant speed so that the traction control system and the ABS shifts to “Sport” level. This mode is designed to ensure stability on may calculate exactly the grip available and the diameter of the the race track in high grip conditions. tyres (the calculation is reset every time the engine stops). If “RACE” mode is selected, this is indicated on the left TFT If this rule is not followed, system performance may be reduced. display as shown below: 156 About your Vehicle

CT OFF mode ESC OFF mode In “CT OFF” mode the F1-Trac traction control is disabled. This In ESC OFF mode the ESC system is disabled. No electronic mode further enhances the already racing -style behaviour of the systems other than the E-Diff control vehicle stability and the vehicle: traction control is disabled while stability control remains driver is allowed complete freedom and control of the vehicle active when a certain level of sideslip is exceeded. The gearshift for track use. This mode is used on the race track in high grip mode, suspension damping and the performance ABS setting are conditions. The gearshift mode, suspension damping and the the same as the previous position. The electronic differential has performance ABS setting are the same as the “RACE” and “CT a specific setting developed to emphasise the dynamic qualities of OFF” modes. the vehicle. Stability is not ensured. This mode is used on the race track in high grip conditions. Warning If “CT OFF” mode is selected, this is indicated on the left TFT display as shown below: In low- to medium-grip conditions (e.g. wet, icy, sandy roads), do not deactivate the ESC system. Important note 4 Every time the engine is started, the ESC system will reactivate. Important note When the brake pedal is pressed, traction control is activated via the VDC system (vehicle dynamics control via the braking system). About your Vehicle 157

If “ESC OFF” mode is selected, this is indicated on the left TFT display as shown below: 158 About your Vehicle

Suspension damping delink button If button A has been pressed and subsequently the position of the Manettino is changed, the suspension setting follows the operating The driver may decide to separate the suspension setting from the logic dictated by the Manettino. logic of the “Manettino” driving mode control switch using the special button A on the steering wheel. Important note By pressing button A, irrespective of the position of the Manettino, the suspension setting shifts to Level 1 (COMFORT). Upon turning off and restarting the vehicle, the suspension setting depends on the position of the Manettino. Position of Suspension Button A pressed Manettino setting When the Manettino is set to SPORT, RACE, CT OFF or ESC OFF, WET COMFORT remains COMFORT shifting to the COMFORT suspension setting by pressing button A SPORT SPORT shifts to COMFORT is indicated by displaying the special symbol and “Bumpy road” message on the left TFT display for 5 seconds. RACE RACE shifts to COMFORT CT OFF ESC OFF RACE RACE shifts to COMFORT shifts to COMFORT 4 A Bumpy road About your Vehicle 159

After 5 seconds, next to the Manettino status in the top of the display, the suspension symbol continues to be displayed as shown in the photo below (example shows Manettino in “SPORT” mode). 160 About your Vehicle

EPB - Electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. The parking brake is applied and released by pulling the relative Always apply the parking brake when the vehicle is parked. lever B on the dashboard to the left of the steering wheel. With the The vehicle should be blocked. If this is not the case, please ignition key turned to II, the relative indicator on the instrument contact the Ferrari Service Network. panel (see page 121) lights up to indicate when the parking brake is engaged. Drive Away function Pull the lever B while holding the brake pedal depressed to release the parking brake. If the ignition key is turned to II, the indicator The EPB electric parking brake also features a “Drive Away” extinguishes once the parking brake is completely released. function: if the driver engages a gear and presses the accelerator with the engine running and with the seat belt buckled, the system The electric parking brake may be used as an emergency brake recognises the driver's intent to set off and automatically releases when the vehicle is in motion. If this is the case, the system acts on the parking brake. 4 all four wheels until button B is released by communicating with the ESP system which prevents locking. EPB deactivation warning If the driver attempts to release the electric parking brake by pulling the lever B without holding the brake pedal depressed, the message “Depress brake pedal and deactivate EPB” is immediately shown on the left hand TFT display (even if system diagnosis is in progress, see page 144), accompanied by an audible warning. B About your Vehicle 161

Autopark Function “Automatic Vehicle Holding” AVH function The EPB Autopark function automatically activates the electric The Automatic Vehicle Holding function of the electric parking parking brake when the engine is switched off. At each Key-on, the brake ensures optimised release when moving off from a standstill: Autopark function is always active by default: this means that the after engine start, the system uses the service brakes to hold the driver does not need to apply the parking brake when the engine is vehicle instead of the parking brake shoes. switched off. If necessary, the function may be temporarily disabled before switching off the engine by pressing the AUTO PARK button C: the message “PARK OFF” is displayed for 5 seconds on the left hand TFT display. In this case, after the engine is switched off, the parking brake must be engaged manually by pulling the lever B. To re-enable automatic EPB engagement at the next key-off, press the button C again; the message “PARK ON” is displayed for 5 seconds on the left hand TFT display. C 162 About your Vehicle

Park Lock Carwash procedure The Park Lock is a locking device built into the gearbox. The Park lock device can be electrically disabled on a temporary This device is used to prevent the vehicle from moving when the basis when the engine is switched off by performing the Carwash multi-disc clutches are open, i.e., with the engine off and/or without procedure. the hydraulic pressure required for gearbox operating. This procedure is necessary when the vehicle has to be moved with The device operates automatically every time the key is turned to the engine off and when washing the vehicle. off: if a gear is engaged when the key is turned to off, the Park Lock is immediately activated. If the gearbox is in “N” (neutral), the Warning Park Lock starts operating after a minimum preset time (needed for the Carwash procedure, see next paragraph). To inform the driver When the Park Lock device is electronically deactivated that the Park Lock has been engaged, the letter “P” is displayed on (Carwash procedure), the vehicle may move. the gearbox display. The vehicle is only kept stationary by the parking brake which must be applied. 4 The Park Lock is deactivated when the engine is running, the first gear or “R” is requested (with the brake pedal pressed) and the luggage compartment lid has been closed correctly. To perform the Carwash procedure, do the following: - with the engine running, select the first gear; - select neutral “N”; - switch off the engine; - turn the key to position II (key-on) within 3 seconds of switching off. The message “Carwash mode activation” will appear on the left TFT display. About your Vehicle 163

Launch Control Important note The “Launch Control” mode is a performance start function. Activating this function optimises vehicle acceleration from a The “Launch Control” function is not available in presence of: standing start. - a sloping road surface, even slight The device, which is not available when the Manettino is set to the - high clutch temperatures. “WET” driving mode, transfers the necessary torque to the ground and avoids skidding of the wheels during acceleration. To start the vehicle in “Launch Control” mode, do the following: - the vehicle must be stationary - the gearbox must be in “Manual” mode - hold the brake pedal down and select first gear - press the LAUNCH L button on the left of the centre console: an acoustic signal informs the driver that the device has been switched on and the word “launch” appears on the gearbox display - press the accelerator pedal and release the brake pedal. L 164 About your Vehicle

“Front Lift” system (optional) Throughout the entire Front Lift system activation cycle, the special warning light (see page 120) remains on in flashing mode whereas On request, the vehicle can be fitted with a front suspension lift the vehicle symbol with an arrow pointing upwards and a message system: this device acts on the front suspension and raises the “Front Lift moving” appears on the left TFT display. When the front of the car by approximately 40 mm (1.5 in.) to make access to system has been activated (front of the vehicle raised), an acoustic garages or steep ramps easier and avoid damaging the car. signal is emitted and the message “Front Lift ON” appears for The system can be activated when the engine is running at a 5 seconds whereas the warning light on the panel stays on in fixed speed of below 40 km/h (25 mph) by pressing button A on the mode until the system is deactivated. centre console. At speeds of over 40 km/h (25 mph), the system To deactivate the system, press button A again: at the start of is deactivated whereas if it is already activated, it is automatically the deactivation cycle, the warning light on the panel starts to deactivated when exceeding 40 km/h. flash again whereas the vehicle symbol with an arrow pointing downwards and the message “Front Lift moving” appears on the left TFT display. The message remains until the system has been completely deactivated. 4 Front Lift moving A About your Vehicle 165

If the engine is turned off with the front suspension lift activated, In the event of engine failure, the “Front Lift” system can however the message “Front Lift ON. Set Front Lift to OFF” appears on the be activated by pressing button A for 10 seconds. In this way, the left TFT display at key-off. Turn the key back to position II (key- vehicle front can be lifted even in emergencies when the engine is on) and press button A to lower the vehicle. If it is not manually turned off (for example, to load it onto the ramp of a breakdown deactivated by pressing the button, within 15 seconds of turning off vehicle). the engine, the system is automatically deactivated. Important note Warning The front suspension lift should only be used for the purposes The system has not been designed to remain activated when described above and not to drive over speed control systems (e.g. the engine is turned off and the vehicle is stationary. If the traffic calmers) more quickly. engine is turned off with the front lift activated, the vehicle is automatically lowered after 15 seconds. Do not use the front suspension lift to park the vehicle on obstacles (e.g. pavements); these obstacles may come into contact with the front of the vehicle and damage it once the system has been deactivated. Front Lift ON 166 About your Vehicle

Stop&Start system (optional) Warning Vehicles with the optional HELE (High Emotion Low Emissions) system have a Stop&Start system that automatically stops the engine Always make sure that the Stop&Start system has been when the vehicle is stationary and restarts it, again automatically, deactivated before carrying out any repair and/or maintenance when the driver wants to set off again. work as indicated on the special labels on the engine compartment lid and underneath the vehicle. The aim of the Stop&Start function is to increase vehicle efficiency by reducing CO2 emissions especially when driving around town. Failure to comply with the above may pose a risk of serious injury to people working on the vehicle. Automatic stopping and restarting of the engine is controlled by sensors and control strategies which, while reducing the impact on vehicle flexibility and comfort to a minimum, guarantee full Warning operating of the safety systems and all the on-board systems even when the engine is switched off, without affecting climate comfort. The driver is personally responsible for leaving the key in the ignition in position II when getting out of the vehicle: the driver Warning must always turn the ignition key to position 0 before getting out of the vehicle. 4 Never leave the vehicle without turning the ignition key to position 0. Warning Always remember to remove the key from the ignition when you get out of the vehicle! Leaving the vehicle with the ignition key in position II puts those who are in the vicinity of the vehicle at serious risk if the Never leave children unattended in the vehicle. engine starts unexpectedly. Warning Warning Make sure that the engine is switched off with the ignition key Always turn the ignition key to position 0 before changing the in position 0 before refuelling. tyres. About your Vehicle 167

How the system works If the Stop&Start system is activated, the LED on button A comes on whereas if the system is deactivated, the LED goes off. If activated, the Stop&Start system decides when to switch off the Deactivation of the system by pressing button A while in a stopped engine and when to restart it according to the driving conditions, vehicle condition (when the engine has been automatically the climate comfort on board and the operating status of the switched off by the Stop&Start function) automatically restarts the vehicle. The system logic does not require drivers to make any engine. change in the way they drive the vehicle. Manual activation and deactivation button The driver can activate/deactivate the Stop&Start system at any time by pressing button A on the roof panel. If the system is activated, pressing button A will deactivate it: the message “Stop&Start OFF” appears for 5 seconds on the left TFT display accompanied by a special symbol. Once the system has been deactivated, pressing button A again reactivates the system: the message “Stop&Start ON” appears for 5 seconds on the left TFT display accompanied by a special symbol. A Stop&Start OFF 168 About your Vehicle

Automatic engine stop mode Important note The engine stops automatically when the vehicle is stationary Each time the ignition key is turned to position II (Key-on), the and the brake pedal is pressed and restarts when the brake Stop&Start system remains in the same state it was in when the pedal is released. switch was turned to position 0 (Key-off). If the function was The left TFT display informs the driver that the Stop&Start system activated at Key-off, it remains activated at the next Key-on and has been activated by displaying the message “Stop&Start active” the LED on button A will flash for a few seconds. accompanied by a special symbol. The message is displayed as long as the vehicle remains in a stop state. To interrupt the display cycle and reduce the message to an icon, press the MODE button with “ESCAPE” function. 4 Stop&Start Stop&Start ON active About your Vehicle 169

Conditions required to activate automatic engine stop To activate the automatic engine stop while driving: Important note - the Stop&Start system must be activated by pressing the button After the first cold start, the Stop&Start system may take a few on the roof panel (LED on) minutes before it is ready. This time period allows some of the - the driver’s seat belt must be fastened. engine parameters (catalytic converter temperature, for example) to reach the values required to reduce emissions. For safety reasons and to guarantee driving comfort and correct operating of the entire vehicle, automatic engine switching-off is deactivated when: Important note - the accelerator pedal is depressed; - a potentially dangerous situation is identified (steep road, vehicle If the engine continues to run when the vehicle is stationary stationary with wheels turned, i.e. when turning at a crossroads or and the brake pedal is pressed, even if the Stop&Start system on a roundabout); appears to be activated, it means that the system has disabled automatic switching off of the engine. When this happens, no - the system recognises vehicle motion in slow traffic or a parking specific signal is displayed on the instrument panel: this is to be manoeuvre (checking reverse gear engagement, time elapsed since considered normal. last stop, driving speed); - maximum air conditioning and heating system performance is requested (“low”, “max defrost” or “rear screen demisting”); - external temperatures are very low or very high; - the gearbox is in the “N” position; - the Front Lift system has been activated; - the DCT gearbox Park Lock has been manually released; - a failure interferes with proper system operating. The system also constantly monitors some of the vehicle operating parameters (battery charge level, engine coolant temperature, catalytic converter temperature, clutch oil temperature, vacuum level in brake servo, climate comfort in passenger compartment) so that engine switching off can be deactivated in certain conditions to guarantee safety and vehicle operating and minimise the impact on on-board climate comfort. 170 About your Vehicle

Information on automatic restarting of engine The system also constantly monitors some of the vehicle operating With the Stop&Start system activated in a stopped vehicle parameters (battery charge level, engine coolant temperature, condition, the driver can restart the engine by: catalytic converter temperature, clutch oil temperature, vacuum level in brake servo, climate comfort in passenger compartment, - releasing the brake pedal vehicle speed) so that the engine can be automatically started in - UP-shifting certain conditions to guarantee safety and vehicle operating and - engaging reverse gear minimise the impact on on-board climate comfort. - pressing the accelerator pedal Warning If the engine is switched off accidentally and not by the Stop&Start system, it must be restarted manually by the driver by pressing the ENGINE START button and reengaging the gear using the shift paddles located behind the steering wheel. This condition is indicated on the left TFT display by the message “Press ENGINE START button to restart”, accompanied by an 4 acoustic signal. For safety reasons and to guarantee comfort when the vehicle is stationary and correct operating of the entire vehicle, the Stop&Start system also automatically restarts the engine when: - the ENGINE START button on the steering wheel has been pressed - the function has been deactivated by pressing the button located on the roof panel - the driver’s seat belt has been unfastened - the driver-side door has been opened - the hard top is being opened or closed - the Front Lift system has been activated - rear screen demisting has been requested or the air conditioning and heating system set to “low” or “max defrost”. About your Vehicle 171

Permanent deactivation of automatic restarting and manual start procedures Permanent deactivation of automatic restarting occurs when: After automatically switching off the engine using the Stop&Start - the luggage compartment lid or engine compartment lid are open; system, automatic restarting requested by the driver may not always - automatic engine restarting has not been successful; be possible: this means that the vehicle systems have permanently - a failure has been detected that may interfere with operating of the deactivated automatic restarting. Stop&Start system. If this occurs, the vehicle must be restarted manually: this condition is indicated on the TFT display by the message “Press ENGINE At times, depending on the seriousness of the failure, the ENGINE START button to restart”, accompanied by an acoustic signal. START button may have to be held down for a few seconds to restart the engine: this condition is indicated on the left TFT display by the message “Press and hold ENGINE START button to start”. Warning If automatic restarting is permanently disabled, the vehicle behaves in the same way as a vehicle with no Stop&Start system: to restart, the driver must perform a manual start by pressing the ENGINE START button and using the shift paddles located behind the steering wheel. Press Press and hold ENGINE ENGINE START START button button to restart to start 172 About your Vehicle

System failure Precautions to be taken during maintenance work If malfunctioning, the Stop&Start system is disabled. The driver is Always turn the ignition key to position 0 before carrying out any informed of the failure by a special symbol that appears on the left repair and/or maintenance work on the vehicle. If work has to TFT display for 20 seconds accompanied by an acoustic signal and be carried out on the vehicle with the ignition key in position II, the following message which corresponds to two different alarm check that the Stop&Start has been deactivated by performing the levels: following procedure before doing any repair and/or maintenance - “Stop&Start failure” (orange symbol) work: - “Stop&Start failure. Go to dealer” (red symbol). if the ignition key is in position II, turn it to position 0 before turning it to II again and press the special Stop&Start system Important note activation/deactivation button on the roof panel (see page 168). If the message “Stop&Start ON” appears on the left TFT display Contact the Ferrari Service Network immediately. when the button is pressed, press the button again. Check that the message “Stop&Start OFF” appears on the left TFT display for When the display cycle ends (20 seconds), or the MODE button with “ESCAPE” function is pressed, the message disappears and the 5 seconds. The button LED must be off. 4 symbol is reduced to an icon. Warning NEVER work on the vehicle if the message “Stop&Start active” appears on the left TFT display. Stop&Start Stop&Start failure failure Go to dealer About your Vehicle 173

Dome light controls (HELE system only) Disconnecting the battery On vehicles with the optional HELE system, the central dome (HELE system only) light B can be switched on or off by holding button C or D down On vehicles with the optional HELE system, the quick release E for (for more than 0.8 seconds). disconnecting the battery from the electrical system (see page 212) The driver-side spotlight and the passenger-side spotlight can be is located on a dummy negative terminal in the bottom left of the switched on and off by pressing and quickly releasing buttons C battery compartment. and D respectively. Warning After disconnecting the battery from the electrical system, place clamp E between bracket F and the battery as shown so that it does not come into contact with the dummy negative battery terminal. E C D E F B 174 About your Vehicle

Seat adjustment Backward/forward adjustment Pull lever B up and slide the seat forward or backward to the desired position. Release the lever and “wiggle” in the seat to check Warning that it is locked in place. As with all adjustment, seat adjustment must be performed when the vehicle is stationary. Warning Correct adjustment is very important for enhanced driving comfort The backward/forward adjustment must consider the fact and maximum efficiency of the passive safety systems. that airbag devices are placed in front of the driver and the passenger (see page 63). Basic seat Correct adjustment must ensure there is adequate space The seat position can be adjusted using the special controls. between the airbag and the driver/passenger (see page 63). Seat back rake adjustment 4 Turn knob C clockwise or counterclockwise until it reaches the required position. B C About your Vehicle 175

Tilting the backrest To tilt the seat, pull lever L up and push the backrest towards the front of the vehicle. When the backrest goes back into position, it will automatically block once it has reached the correct position. L 176 About your Vehicle

Electrically-adjustable seat (optional) Seat back rake adjustment The seat position can be electrically adjusted using the special Use control E to adjust the seat back rake. Push the control forward controls. or backward to adjust the seat back rake. Three adjustments are possible using control D: Lumbar support adjustment (Full Electric option) - backward/forward adjustment: push the control forwards or Use control F to adjust the lumbar support. Push the control on the backwards seat symbols to increase or decrease the lumbar support. - height adjustment: push the control up or down - seat inclination (tilting): push the front or rear end of the control Backrest and cushion side width adjustment (Full Electric option) up or down to adjust seat inclination. Use control G to pneumatically adjust the width of the backrest sides and the seat cushion. Push the control on the seat symbols to Warning increase or decrease the side width. The backward/forward adjustment must consider the fact that airbag devices are placed in front of the driver and the passenger (see page 63). 4 Correct adjustment must ensure there is adequate space between the airbag and the driver/passenger (see page 63). D E About your Vehicle 177

Driver’s seat position memory (Full Electric option) With reverse gear engaged, the position of the passenger external When a door is open and the key is in position 0, the seat can be rear-view mirror can be adjusted to a position other than the moved for a limited period (approx. 15 sec.). Each time a door is driving position, to help parking manoeuvres. This position can be opened or both doors are closed and the key is set to OFF, the seat memorised along with all the other memorisable positions. can be moved again for a limited period. If the personalised reverse gear position is never set, when the The seat position can only be memorised when the key is in reverse gear is engaged, the passenger external rear-view mirror position II, by pressing one of the three buttons 1, 2 or 3 (H) each will in any case move slightly downwards and inwards (compared one corresponding to a memorisable position. Pressing one of these with the driving position). buttons for longer than 3 seconds memorises the position of the driver seat, rear-view mirrors and steering wheel (confirmed by emission of a double tone). To recall the memorised position, press one of the buttons H and release it within 3 seconds. Operation begins as soon as the button is released. Recalling the memorised position is not allowed when the vehicle is in motion. If the vehicle starts to move while the memory recall is being operated, the seat and column do not stop moving and reach the memorised position. � � � 178 About your Vehicle

Seat heating system (Full Electric option) Tilting the backrest Turn control N to activate the seat heating function. To tilt the seat, pull lever L up and push the backrest towards the When this function is active on one or both seats, the relative front of the vehicle. warning light on the panel comes on. Using control N, the driver When the backrest goes back into position, it will automatically can adjust the heating, choosing from 3 levels identified on the block once it has reached the correct position. control with the numbers 1, 2 and 3. In position 0, seat heating is not activated. Warning Do not use the electric seat adjustment controls when the backrest is tilted. 4 � L About your Vehicle 179

Super Racing seat Seat back rake adjustment The seat position can be adjusted using the special controls. Turn knob Q clockwise or counterclockwise until the desired back rake has been reached. Backward/forward adjustment Tilting the backrest Pull lever P up and slide the seat forward or backward to the desired position. Release the lever and “wiggle” in the seat to check Pull lever R up to tilt the backrest forward. that it is locked in place. Warning The backward/forward adjustment must consider the fact that airbag devices are placed in front of the driver and the passenger (see page 61). Correct adjustment must ensure there is adequate space between the airbag and the driver/passenger (see page 61). Q R P 180 About your Vehicle

Adjusting the steering wheel Rear-view mirrors The steering wheel can be adjusted for rake and reach. Internal rear-view mirror Warning Hold the internal rear-view mirror and move it to the required position. Do not adjust the steering wheel when the vehicle is moving. On request, the internal rear-view mirror can be fitted with an electrochromic mirror that automatically darkens to reduce the Mechanical adjustment dazzling effect of the reflected light on the driver. The speed with 1) Unlock lever X by pushing it forward. which the mirror darkens depends on the intensity of the light. 2) Adjust the position of the steering wheel. By pressing button B you can activate/deactivate the electrochromic 3) Lock the steering wheel by pulling lever X until it locks into mode. When the electrochromic mode is activated, the green place. LED D comes on. Electric adjustment (optional) It can only be adjusted if the ignition key is in position II. Move 4 control A to the left of the steering column. On versions with a driver's seat with memory, the position of the steering wheel is memorised together with the position of the external rear-view mirrors when the seat position is memorised. X D A B About your Vehicle 181

External rear-view mirrors On versions equipped with a driver's seat with memory, every These mirrors can be electrically adjusted using the control C (with time the seat position is memorised, the external rear-view mirror the ignition key in position II) and are equipped with defogging position is also stored automatically, both for the normal travelling elements. direction and reverse manoeuvring. 1) Mirror selection: turn control C to the left or right lock position To memorise a new position of the external rear-view mirrors, to select the mirror that requires adjusting. turn the ignition key to position II and adjust the position of the mirrors; then engage reverse and reposition the external mirrors to 2) Mirror positioning: move control C in the four directions (up – ensure the best possible visibility to perform the manoeuvre, then down – right – left) to adjust the selected mirror. disengage reverse gear. 3) Mirror closure (optional): turn control C to the lower central Finally, press one of the buttons 1, 2 or 3 on the seat (see lock position to close the rear-view mirrors. page 178), each one corresponding to a memorisable position, until Once adjusted, move the control C into the upper central position a double tone confirms that the procedure is complete. where it will be locked in order to avoid changing the external The new position of the external rear-view mirrors will be mirror setting inadvertently. automatically memorised together with the seat position. The mirrors will yield in both directions in the event of a collision: In addition, the mirror positions can be adjusted for both the if necessary, the mirrors can be pushed both backwards and normal travelling direction and for reverse manoeuvring. forwards. Warning The rear-view mirrors must always be positioned correctly while driving. Do not adjust the rear-view mirrors when the vehicle is moving. On request, the external rear-view mirrors can be fitted with an electrochromic mirror. C C 182 About your Vehicle

Air conditioning and heating system Controls 1 Left-hand temperature setting and AUTO button Operating modes 2 A.C. compressor activation/deactivation Automatic 3 Single-zone mode activation/deactivation This mode automatically adjusts the air distribution, temperature 4 Air distribution fan speed and ventilation levels according to the temperature set by the user. 5 Rear window demist activation/deactivation Partially Automatic 6 Windscreen demist activation/deactivation This mode allows the user to adjust certain parameters manually, 7 Right-hand temperature setting and AUTO button while others remain automatic. 8 Right-hand air distribution mode setting Manual 9 Air recirculation This mode allows the user to set the values to suit the passengers’ 10 Left-hand air distribution mode setting needs. 4 1 2 3 4 5 6 7 10 9 8 About your Vehicle 183

Left-hand temperature setting and AUTO button (1) Air distribution fan speed (4) This is used to select the required air temperature in the left-hand The four setting positions allow the occupants to select the air flow side of the passenger compartment; the AUTO button is used to rate. activate automatic operation (LED on). Rear window demist activation/deactivation (5) A.C. compressor activation/deactivation (2) Press this button (LED on) to activate rear window defogging/ This is used to activate (LED on) or deactivate (LED off) the A.C. demisting. compressor. Windscreen demist activation/deactivation (6) Single-zone mode activation/deactivation (3) Press this button (LED on) to activate windscreen defogging/ This is used to activate (LED on) or deactivate (LED off) the demisting. single-zone operating mode. 1 2 3 4 5 6 184 About your Vehicle

Right-hand temperature setting and AUTO button (7) Air recirculation (9) This is used to select the required air temperature in the right-hand If released (LED off), the air flow comes from outside the side of the passenger compartment; the AUTO button is used to passenger compartment. activate automatic operation (LED on). When outside temperatures exceed 32 °C (90 °F), the air Right-hand air distribution mode setting (8) recirculation feature remains on with a 60-second pause every This is used to select one of the six air flow distribution modes in twenty minutes to refresh the air. the right-hand side of the passenger compartment. If you activate the windscreen washer function, the air recirculation feature activates for 20 seconds, to prevent any smell of detergent products from entering the passenger compartment. If pressed (LED on), the air flow comes from inside the passenger compartment. The recirculation increases air heating or cooling. Left-hand air distribution mode setting (10) This is used to select one of the six air flow distribution modes in 4 the left-hand side of the passenger compartment. Once the internal temperature has stabilised at the desired level, you are advised not to change the position of the temperature selection switch unless the external temperature changes drastically. 8 10 7 9 About your Vehicle 185

Maintenance The pollen filter must be replaced every year, as indicated in the Important note “Maintenance Schedule”. We recommend keeping the air flow set to open and directing the air flow to a neutral position. Important note The air coming out of the vents does not correspond to the temperature requested by the user, but is the temperature required to maintain the desired temperature inside the passenger compartment. Adjusting the air vents The adjustable air vents are positioned on the sides and in the central section of the dashboard. Use control A to direct the air flow. Use control B to adjust the air flow rate. Turned to left: closed. Turned to right: open. A B 186 About your Vehicle

Passenger compartment accessories Opening of the glove compartment can be deactivated by pressing button C. Call up the MENU screen page on the left TFT display Glove compartment (see page 98) and then select the items “Car setup”, “Glove box This is located on the passenger side of the dashboard. To open key” and OFF. To reactivate opening using the button, select ON. it press the OPEN C button on the centre console: the glove compartment will move down slowly by way of a damped opening mechanism. The glove compartment is illuminated by an internal light that comes on automatically when it is opened. Warning Keep the glove compartment closed while driving. To close the glove compartment, push the top part until you hear the click of the lock. 4 C About your Vehicle 187

Pocket-change compartments Sun visors They are located on the lower part of the doors and on the centre The sun visors can be moved by pulling them down towards the console. windscreen and sideways by unhooking them from the fastener and There is also a cup holder in the front of the centre console. turning them towards the door glass. 188 About your Vehicle

12V power socket Rear shelf The power socket D on the centre console can be used to power The rear shelf can be used to transport light luggage such as the small electrical appliances such as mobile phones, lights, vacuum two bags supplied on request or a golf carry bag. cleaner and any other accessory with absorption not exceeding 140 Watts and a voltage of no more than 12 Volts. Warning Warning Only place light luggage on the rear shelf. Prolonged use of this device may discharge the battery. Do not try to insert plugs into the power socket that are not the right size and shape. 4 Warning Use the power socket to connect the tyre repair and inflation kit in an emergency ONLY for the amount of time strictly necessary. D About your Vehicle 189

Toolkit ................................................................ 192 Replacing light bulbs ........................................... 197 Replacing a fuse .................................................. 200 Replacing a wheel ................................................ 208 Towing ................................................................ 210 Battery ................................................................ 212 Battery conditioner .............................................. 216 EPB emergency release ......................................... 220 Park Lock emergency release ................................ 222

5 ADVICE FOR EMERGENCY SITUATIONS

Toolkit Warning Tool bag Repair work using the toolkit requires: Stored in the luggage compartment, it contains the necessary tools - suitable protective equipment (e.g. gloves) for emergency repair jobs: - adequate precautions to be taken (e.g. during tyre replacement • pair of cotton gloves; never lie under a vehicle raised by a jack) • set of fuses; - minimum specific expertise when working in contact with electrical parts/components (e.g. battery). • pliers for removing fuses; • tow hook; • hex-head wrench for removing battery crossbar; • insulated cutting pliers; • funnel for emergency fuelling; • screwdriver for slotted and crosshead screws; • EPB emergency release tool; • Park Lock emergency release tool. 192 Advice for Emergency Situations

Warning The Electric Parking Brake (EPB) emergency release tool and the Park Lock emergency release tool may only be used by specialised workshop personnel, as indicated on the label in the tool bag. Warning The Electric Parking Brake (EPB) emergency release tool is flexible and is kept folded up in the tool bag: remove the tool from its housing very carefully to prevent the end flying out. 5 Advice for Emergency Situations 193

Emergency tyre repair and inflation kit Stored in the luggage compartment, it can be used in the event of a Warning puncture or low tyre pressure to repair and/or inflate a tyre enough Damage to the wheel rim that causes air leaks cannot be to continue the journey safely. repaired. Do not remove foreign objects (screws or nails) that have penetrated the tyre. Important note To use the tyre repair and inflation kit correctly, refer to the Warning instruction booklet supplied with the kit. After using the repair kit, the vehicle must be considered in an emergency situation: drive with the greatest care (maximum Warning permissible speed 80 km/h - 50 mph). Give the instruction manual supplied with the kit to the personnel that will handle the tyre repaired with the tyre repair Warning kit. Apply the sticker supplied with the kit where it can easily be seen by the driver to indicate that the tyre has been treated with Warning the tyre repair kit. In the event of a puncture caused by foreign objects, tyres can Drive carefully especially on bends. be repaired with cuts of up to 4 mm in diameter on the tyre Avoid sudden accelerations or braking. tread and shoulder. Warning Warning The kit is to be used to temporarily repair only one tyre Punctures cannot be repaired on the sides of the tyre. Do not punctured by small objects: the kit may not be useful in the case use the tyre repair kit if the tyre has been damaged after driving of large punctures or tearing. with a flat tyre. 194 Advice for Emergency Situations

Important note Warning After driving for approximately 10 minutes, stop and recheck Keep the kit in its box and out of children’s reach. the tyre pressure. Do not inhale or swallow the fluid contained in the cartridge Remember to apply the parking brake. and avoid contact with the skin and eyes. Warning Warning If the pressure has decreased below 1.8 bar (26.11 psi), do The spray contains ethylene glycol and latex. not continue driving: the kit cannot guarantee the correct hold The latex may cause an allergic reaction, is harmful if swallowed because the tyre is too damaged. Contact the Ferrari Service and is irritating to eyes. May cause sensitisation by inhalation Network. and skin contact. Avoid contact with eyes, skin and clothing. If the tyre pressure is at least 1.8 bar (26.11 psi), restore the In case of contact, rinse immediately with plenty of water. If correct pressure and continue driving. swallowed, do not induce vomiting, rinse mouth, drink plenty of Drive very carefully to the nearest Ferrari Service Network. water and seek immediate medical advice. Keep out of reach of children. The product should not be used by asthma sufferers. 5 Do not inhale vapours during use. In the event of an allergic Warning reaction, seek immediate medical advice. Store the spray can in its special case away from sources of heat. The repaired tyre must be replaced as soon as possible and the The liquid sealant has an expiry date: the expiry date is workshop personnel must be informed that the tyre was treated indicated on the kit. with tyre repair fluid. Advice for Emergency Situations 195

Useful accessories Environment In addition to the tools supplied with the vehicle, the hazard warning triangle and fluorescent safety jacket should always be Replace the spray can containing the expired liquid sealant. Do kept on board in order to signal hazardous situations in compliance not dispose of the spray can and sealant in normal domestic with regulations. waste. Dispose of in accordance with national and local regulations or ask the Ferrari Service Network to take care of disposal. Warning The sealant in the kit cartridge can damage the sensor inside the wheel rim on vehicles fitted with a tyre temperature and pressure monitoring system (TPMS). If this occurs, the sensor must be replaced. Contact the Ferrari Service Network. Warning Wear the protective gloves supplied with the tyre inflation and repair kit. 196 Advice for Emergency Situations

Replacing the front and rear light bulbs Replacing number plate light bulbs To replace a number plate light bulb, proceed as follows: Important note • remove the light from the right side where there is a spring clip; To replace the front and rear light bulbs, contact the Ferrari • remove the transparent cover A from its housing; Service Network. • replace the bulb by removing connector B from its housing; To adjust the headlight beam, please contact the Ferrari • refit the connector and transparent cover by inserting it first from Service Network. the left side and then pressing on the other side. 5 B A Advice for Emergency Situations 197

Replacing other light bulbs Glove compartment, underdoor and luggage compartment bulbs Roof dome light • Use a screwdriver to gently prise under the edge of the transparent cover G and lift it. • Use a screwdriver to gently prise under the edge of the transparent cover C of the dome light and remove it from the roof • Completely remove the transparent cover from its housing. panel. • Take the bulb out of its clips. • Replace the bulb D or E or F. • Replace the bulb. • Refit the dome light and make sure that the wires are not trapped • Refit the transparent cover and make sure that the wires are not by inserting it first from the connector side and then pressing on trapped by inserting it first from the connector side and then the opposite side. pressing on the opposite side. Follow the same procedure for replacing the underdoor light bulbs and the luggage compartment dome light bulb. � � � G � 198 Advice for Emergency Situations

Light bulbs (12 V except for high beam and low beam) Type Power Low beams and high beams gas-discharge (XENON) Das Front running lights LED Front turn indicator lights LED Side turn indicator lights incandescent T4W Running and stop lights LED Reverse lights incandescent H6W Supplementary stop lights LED Rear turn indicator lights LED Rear fog lights incandescent W16W Number plate lights incandescent 5W Passenger compartment dome light Spotlights incandescent incandescent 8W 5W 5 Glove compartment light incandescent 5W Underdoor courtesy lights incandescent 5W Luggage compartment light incandescent 10W Advice for Emergency Situations 199

Replacing a fuse Fuse colours When an electrical device is not working, check that the Ampere corresponding fuse is not blown. yellow ochre 5 A - Unblown fuse. brown 7.5 B - Blown fuse. red 10 Important note light blue 15 If the problem persists, contact the Ferrari Service Network. yellow 20 white 25 Important note green 30 When replacing a fuse, always use fuses of the same amperage (same colour). Maxi fuse colours Ampere The tool bag contains spare fuses. yellow 20 To remove the fuses, use the pliers C in the tool bag. green 30 orange 46 red 50 � blue 60 � � 200 Advice for Emergency Situations

Location of the fuse and relay boxes A - Fuses and relays in battery compartment B - Body Computer fuses and relays C - Fuses and relays in passenger compartment on passenger side D - Fuses and relays on driver-side rear side panel D C A 5 B Advice for Emergency Situations 201

Fuses and relays in battery compartment Engine relay and fuse ECU power supply F-70 150 To access these fuses: (SCM) • remove the passenger footrest; F-71 40 Front lift pump • using the hex-head wrench in the tool bag, remove the crossbar T F-72 40 Parking brake power by unscrewing the two screws E; F-73 70 Dashboard ECU power • remove the cover of box A located above the positive terminal on the right side of the battery. Body Computer fuses and relays Important note To access these fuses, remove the dashboard panel 1. Only open the boxes containing the fuses that need to be Important note checked to avoid damaging other components. Only open the boxes containing the fuses that need to be Box A contains these fuses: checked to avoid damaging other components. Ref. Amp. Use CAL5 CAL5 Power supply (starter motor and alternator) E E T A 202 Advice for Emergency Situations

Box B contains these fuses and relays: F-39 15 Dashboard ECU devices (NBC interconnection) Ref. Amp. Use F-40 30 Heated rear window F-12 15 Right high beam F-42 7.5 Alternator F-13 15 Left high beam F-43 30 Windscreen washer/wiper relay power supply INT/A for dashboard ECU and Body F-44 20 Passenger seat heating, cigarette lighter F-31 7.5 Computer Node relay coils F-47 30 Driver-side door, driver-side power window Dome lights, foot well and step lights, Side Passenger-side door, passenger-side power F-32 10 F-48 30 Marker relay coil window F-34 30 Suspension Control Node Rain and twilight sensor, parking sensors, Stop light control, clutch control, air parking brake control, column adjustment F-35 7.5 conditioning node F-49 7.5 control, hazard warning lights, Steering Wheel Node, Differential Control Node, radio, CAN Volumetric anti-theft system, parking sensors, F-36 10 box interface fuel filler flap relay coil F-50 7.5 Airbag Node, weight sensor Stop light control, Instrument Panel Node, 5 F-37 10 Suspension Control Node F-51 7.5 Semi-automatic Gearbox Node F-38 15 Luggage compartment lock actuator B F-72 F-73 F71 F-71 F-72 F-73 F-70 F-70 CAL2 CAL5 1 Advice for Emergency Situations 203

F-52 15 Power socket, driver seat heating Fuses and relays in passenger compartment on passenger side F-53 10 Instrument Panel Node power supply These fuses are located behind the glove compartment 2. T01 20 Low beam relay Boxes C contain these fuses and relays: T11 30 Heated rear window relay T12 30 Service relay 1 (dependent on INT/A ignition Ref. Amp. Use switch) F-01 60 +30 Radiator fan relay 2 T13 50 Jumper (service power supply 2) F-02 30 +30 ABS (valves) F-03 30 +30 Hard top Node (pump) F-04 50 +30 ABS (pump) F-05 40 +30 Air conditioning Node F-06 50 +30 Radiator fan relay 1 F-07 20 +30 Horn relay F-08 7.5 Air conditioning and heating system compressor F-09 7.5 +30 Supplementary stop light relay (third stop light) 2 204 Advice for Emergency Situations

F-10 15 +30 Fuel pump relay 1 F-84 15 +30 Fuel pump relay 1 F-11 25 Left bank oxygen sensor F-85 25 Headlight washer F-14 15 +30 High beam relay F-87 25 Right bank oxygen sensors F-15 7.5 +30 Power supply for EPB-activated stop light F-88 10 +15 Left cylinder bank injection system control relay, right headlight LED module F-89 10 +15 Right cylinder bank injection system power supply relay F-91 15 +30 Tyre pressure node, LH headlight LED F-16 25 +30 Right bank engine control power supply module relay F-17 25 +30 Left bank engine control power supply F-92 7.5 +30 Alternator sensing F-18 10 +30 Left cylinder bank injection system power F-93 30 +30 Ignition switch supply, LH cylinder bank injection main relay coil F-94 15 +30 Radio/CAN box/ICP/clock spring/Japan navigation system stabiliser F-19 10 +30 Right cylinder bank injection system power supply F-95 10 +30 Current stabiliser F-20 30 +30 Right cylinder bank injection system main F-97 30 +30 Stabiliser for Becker amplifier F-21 15 relay +30 Fuel pump relay 2 T02 T03 30 30 High beam relay Fuel pump second speed relay 5 F-22 15 Left bank (ignition coil) F-23 10 +30 ABS (electronic) C F-24 15 Right bank (ignition coil) F-30 30 +30 HI-FI amplifier relay F-81 40 +30 Supplementary ECU power supply F-82 70 +30 Dashboard ECU and ECU on driver-side rear side panel power supply C F-83 50 +30 Air pump relay Advice for Emergency Situations 205

T05 30 Fuel pump relay 2 T29 30 Supplementary stop light relay (third stop light) T06 30 Glove compartment relay T30 50 Air pump relay T07 50 Horn relay T31 30 Headlight washer pump relay T08 30 Air conditioning and heating system T37 30 Radiator fan relay 2 compressor relay T38 30 Left headlight LED module power supply T09 30 Left cylinder bank injection system main relay relay T10 30 Right cylinder bank injection system main T39 30 Right headlight LED module power supply relay relay T14 30 Fuel pump relay 1 T40 30 Radiator fan relay 1 T17 10/20 INT/A relay (devices excluded at ignition) T19 30 EPB-activated stop light control relay T20 30 Starting relay T26 10/20 Windscreen wiper first speed relay T27 10/20 Windscreen wiper second speed relay T28 30 Windscreen washer pump relay 206 Advice for Emergency Situations

Fuses and relays on driver-side rear side panel F-65 20 +30 Door lock actuator To access these fuses, remove the driver-side rear side panel 3. F-66 7.5 +30 Semi-automatic Gearbox Node Boxes D contain these fuses and relays: F-67 7.5 Side Markers 2 (RH front and LH rear) Ref. Amp. Use F-78 15 +30 Battery charger F-54 15 +30 Gearbox cooling fan F-80 30 +30 Starting relay F-56 30 +30 Driving Position Node T21 50 Side Marker relay F-57 7.5 Side Markers 1 (LH front and RH rear) T22 30 Reverse light relay F-59 7.5 Reverse light power supply T23 30 Fuel filler flap relay F-60 30 +30 Passenger Position Node T24 30 Gearbox cooling fan relay F-61 7.5 +30 Driver Position Node (electronic), front lift T25 30 Semi-automatic gearbox main relay F-62 7.5 +30 Passenger Position Node (electronic) T43 30 Start enable relay F-63 15 +30 Semi-automatic gearbox main relay F-64 7.5 Fuel filler flap actuator power supply 5 D 3 Advice for Emergency Situations 207

Replacing a wheel • additional tool bag C containing the jack for raising the vehicle and the socket wrenches for operating the jack and tightening the wheel stud bolts. Important note If one or more wheels need to be replaced, proceed as follows: Warning • replace the wheel stud bolts with damaged threads or tapers The spare wheel must only be used for short trips in the event • carefully clean the wheel stud bolts before fitting of an emergency. • do not lubricate the contact surfaces between the stud bolt When the spare wheel is fitted, never exceed the maximum and the wheel rim and between the wheel rim and the brake speed of 80 km/h (50 mph) and drive carefully, especially disk. around bends and when overtaking, avoiding sudden In order not to remove the antilock coating, do not clean the acceleration or braking. wheel rim cones with solvents or aggressive products. Do not exceed the approved weight limits. Do not fit snow chains on the spare wheel. Collapsible spare wheel (optional) Never fit more than one spare wheel at a time. On request, the vehicle comes with a kit containing: • collapsible spare wheel A with space-saving tyre; label B indicates the maximum speed allowed of 80 km/h (50 mph); Important note Failure to comply with these instructions could lead to loss of control of the vehicle and consequently damage to the vehicle and injuries to its occupants. � � � 208 Advice for Emergency Situations

Replacing a wheel • Raise the vehicle carefully using jack E until the wheel is off the • Position the vehicle on an even surface, then block the rear wheels ground. by applying the parking brake. Warning Warning If the jack is not positioned correctly, the vehicle could slip off. Make sure that the vehicle is in a safe position by applying the Make sure that no part of the body is underneath the vehicle parking brake. while changing the wheel. The supplied jack must only be used for changing wheels. • If necessary, switch on the hazard warning lights and place the hazard triangle at the required distance from the vehicle. • Unscrew the five stud bolts and remove the wheel. • Take the spare wheel and tools out of the luggage compartment. • Fit the uninflated collapsible spare wheel. • Loosen the five wheel stud bolts approximately one turn each • Screw the stud bolts into place but do not tighten them. using wrench D supplied. • Place the base of the jack E on flat firm ground under one of the Warning jacking points F on the underfloor as shown in the figure. Inflate the collapsible spare wheel before lowering the vehicle to avoid damaging the rims. 5 • Inflate the collapsible spare wheel using the inflation kit. F E D Advice for Emergency Situations 209

Towing Warning When towing the vehicle, avoid using anchor points that are not The kit must be used in “tyre inflation” mode. Refer to the designed for tow hook A inserted in housing C. instruction manual supplied with the kit. Proceed as follows: • take tow hook A out of the tool bag; • Inflate the spare wheel to the indicated pressure (see page 28). • open cover B in the right-hand side of the front bumper; • Lower the vehicle and remove the jack. • tightly screw tow hook A into housing C; • Tightly fasten the stud bolts, alternately going from one stud bolt • release the EPB; to one that is diametrically opposite. • release the Park Lock. As soon as possible, tighten the stud bolts with the torque wrench to a torque of 100 Nm. Warning If there is an electrical system failure, release the EPB and Park Warning Lock manually (see pages 204-206). The spare wheel does not have a tyre pressure monitoring sensor (see label on spare wheel tool bag). After fitting, it is not checked by the system but complies with international regulations ECE R64/01. After fitting, we recommend that you go to the nearest Ferrari Service Network. A B 210 Advice for Emergency Situations

Fuel inertia switch Warning The fuel inertia switch is a safety device which deactivates the fuel While towing the vehicle, you must comply with Road pump relays if a collision occurs. Regulations. A symbol appears on the left TFT display and the hazard warning lights come on to indicate that the switch has been activated. When the fuel inertia switch is activated, the doors are also Warning unlocked (if locked) and the central dome light comes on. Do not tow the vehicle by attaching to levers, suspension and wheel rims but only to the tow hook properly fitted in place. Warning Keep the key in position II to enable the lights to work and The fuel pump relays can be reactivated by pressing the button prevent the steering wheel from locking if it is turned; when in the battery compartment which can be accessed by opening towing the vehicle, do not start the engine. the passenger side footrest. Important note Remember that when the engine is switched off, the power steering and brake servo functions do not work. 5 C Advice for Emergency Situations 211

Battery Disconnecting the battery The battery is located in the passenger compartment behind the Before disconnecting the battery, deactivate the electronic alarm passenger side footrest. using the remote control. Checking the battery Warning Never disconnect the battery from the electrical system when Warning the engine is running. The battery does not need topping up with distilled water or Before disconnecting the battery, lower the side windows by at sulphuric acid. least 2-3 centimetres (0.8-1.2. in.) to avoid damaging the strips when opening and closing the doors. Warning Warning The battery must only be removed from the vehicle by the Ferrari Service Network. When the battery is connected and charged, this operation is automatically performed when the doors are opened and closed. The windows must remain lowered until the charged battery is Warning reconnected. If the battery is discharged and the windows are fully up, only open the doors when strictly necessary and take Do not place the battery near sources of heat, sparks or naked great care; do not close them again until the windows can be flames. lowered. The vehicle is equipped with a sealed lead acid battery that does not require maintenance. Important note • Periodically check that the terminals and pins are clean and firmly We recommend using the battery conditioner if the vehicle is secured. going to left unused for a long period. • Visually inspect the outer casing for any cracks. • If the battery overcharges, it will wear out quickly. Have the To cut off the power supply from the battery to the electrical vehicle electrical system checked if the battery tends to discharge system, use the quick release C on the left side of the battery. Use easily. the locking lever to loosen the terminal. 212 Advice for Emergency Situations

Detach the terminal from the battery: the power supply from the Reconnecting the battery battery to the electrical system is cut off. Place the clamp on the battery and fasten it by closing the locking lever. Warning Each time the battery is reconnected, do the following before starting the engine: The battery quick release must only be used if the battery conditioner cannot be connected. - close both doors and close the luggage compartment lid; unlock and lock the doors using the remote control; open the luggage compartment lid using the remote control; Warning - adjust the clock (date and time on instrument panel); Place the terminal so that it does not come into contact with the - close both doors and fully raise the driver side and passenger side battery terminal or other metal parts of the vehicle. windows to their upper limit; check that the windows move down to the “target position” when the doors are opened. Warning Before starting the engine, wait at least 60 second with the ignition key in position II to allow the electronic system that controls the motor-driven valves and the AC ECU to run a self- acquisition process. 5 During this period, no devices must be activated. The Motronic ECU self-acquisition cycle will only function correctly C when the intake air temperature is above 5 °C (41 °F). After removing the battery from the vehicle or disconnecting it from the electrical system using the battery master switch, it is important to check that the external temperature is within the indicated values when reconnecting before performing the self- acquisition cycle. Advice for Emergency Situations 213

Emergency starting To perform an emergency start, do the following: If the battery is flat, you can perform an emergency start by • Apply the parking brake. connecting the special jump leads to the battery of another vehicle, • Deactivate all the electrical devices. a portable jump starter or an external battery. • Using the hex-head wrench in the tool bag, remove the crossbar T by unscrewing the two screws E. Important note • Remove cover F of the fuse box located above the positive Emergency starting can only be performed with batteries with a terminal on the right side of the battery. nominal voltage of 12 V. • If emergency starting is performed using the battery of another vehicle, leave the engine on the other vehicle to idle. • Using the jump leads, connect the positive terminal of the battery Important note to the positive terminal of the portable jump starter or external For emergency starting, only use leads that do not allow reverse battery going from the battery on your own vehicle. polarity, with sufficient cross-section and insulated clamps. • Connect the negative terminal of the portable jump starter or external battery to an earthing point on your vehicle using the jump lead going from the external battery. • Start the engine. E E T F 214 Advice for Emergency Situations

• Disconnect the jump lead from the earthing point and then from the positive terminal of the battery on your vehicle. Warning After emergency starting, go to the nearest Ferrari Service Network immediately to get the battery checked. 5 Advice for Emergency Situations 215

Battery conditioner After connecting the battery conditioner to the socket in the vehicle, run the connection cable under the passenger door on the The vehicle is equipped with a battery conditioner to maintain and front side. recharge the battery. Important note Important note Do not run the connection cable out of the vehicle in positions Using the battery conditioner will extend the life of the battery. other than those indicated to prevent damaging the seals and/or the cable. The device is kept in a pocket inside the car cover bag supplied with the vehicle. If you do not plan to use the vehicle for over a week, we The battery conditioner connection socket D is located under the recommend you connect the battery conditioner to keep the battery dashboard on the passenger side. in perfect working order. Warning Warning Place the battery conditioner where it can be easily seen away The engine cannot be started as long as the battery conditioner from heat sources and out of children's reach. is connected to the vehicle socket. D 216 Advice for Emergency Situations

Exhaust system overheating alarm devices Important note (“Slow Down” function) Additional technical information on the use of the device can be If the engine is running unevenly resulting in exhaust system found in the manual provided inside the pocket of the car cover overheating, the “Slow Down” function is activated: a special bag. symbol (see page 118) appears on the left TFT display accompanied by a message. The message varies according to three alarm levels: • Temperature high: “Catalysts temp. high. Slow down”. • Temperature too high: “Catalysts temp. too high. Engine performance limited”. • Catalytic converter temperature system failure: “Catalysts temp. not plausible. Go to dealer slowly”. Displaying of the message is controlled by the thermistor via the engine control ECU. Warning Incorrect use of the vehicle may cause the “Slow Down” 5 function to be activated. Warning If the temperature is high: slow down immediately so that the exhaust system temperature decreases. Advice for Emergency Situations 217

Clutch overheat alarm devices Warning Extremely high performance use of the vehicle at high engine If the temperature is too high: speeds for prolonged periods and at high ambient temperatures the temperature in the catalytic converters has reached a may cause the DCT gearbox clutches to overheat. In this case, the dangerous level and could damage them; if you continue to following safety warnings will be displayed on the left TFT display, drive, the engine control ECU intervenes and reduces the corresponding to two different alarm levels: torque produced by the engine. • The message “Clutch overheated” The torque limit remains active until the catalytic converter • The message “Clutch overheated” accompanied by an acoustic temperature goes down to normal operating values. signal. When the message “Clutch overheated” is displayed, the driver may notice a difference in the behaviour of the system during gearshifts Warning and/or during standing starts. If catalytic converter temperature system failure information is displayed: - the engine control ECU intervenes and reduces the torque produced by the engine - the driver must slow down and slowly drive to the nearest Ferrari Service Network to have the engine parameters checked. Warning If the EOBD warning light (see page 117) comes on at the same time as the “Slow Down” message, go to the nearest Ferrari Service Network to have the ECU error memory checked. Do Clutch overheated not proceed in any other way. 218 Advice for Emergency Situations

Engine malfunction alarm devices Important note If the “engine control system failure ” (EOBD, see page 117) Certain high-performance actions (including but not limited to: warning light flashes or comes on permanently while the engine is “LAUNCH” control start, standing start with wheelspin with running, it indicates that the engine or the emission control system Manettino set to ESC OFF, etc.) may be inhibited to prevent may be malfunctioning. excessive overheating of the clutches: the system warns the The electronic system detects and isolates the error preventing driver that the action is not permitted by displaying the message damage to the engine or the production of harmful emissions. “Operation not admissible” on the left TFT display. Warning Warning When the “engine diagnostic system failure” warning light As soon as any of the warnings described above appear on the comes on, engine performance may be considerably reduced. left TFT display, the driver must slow down, continue driving Drive carefully, avoiding sudden acceleration and high speeds. at an engine speed between 2000 and 3000 rpm and minimise Contact the Ferrari Service Network immediately. gearshift frequency to allow the clutches to cool down as quickly as possible. These driving conditions must be maintained until the message “Clutch overheated” is no longer displayed. 5 Advice for Emergency Situations 219

Replacing the brake pads and discs Emergency release of the electric parking brake (EPB) Brake pads The front brake pads have a wear detector connected to the brake Warning warning light; if this warning light comes on or braking is not The release procedure must only be carried out by specialised even, have the pad thickness and the state of the braking surfaces workshop technicians. checked. If the system cannot be released, contact the nearest Ferrari The minimum brake pad thickness is 3 mm - 0.12 in. (thickness of Service Centre. the friction material only). Replacing brake pads When the brake failure warning light comes on, it means that Warning the front brake pads are excessively worn and must be replaced When the electric parking brake is deactivated manually, the immediately. vehicle may move. To keep the vehicle stationary, the Park Lock safety device must Warning be applied: make sure that the letter “P” appears on the gearbox To guarantee the quality of the components and proper display. installation, we recommend that you have the brake pads replaced at a Ferrari Service Centre. After replacement, avoid sudden braking until the new pads are seated properly (approximately 300 km - 186 mi). A 220 Advice for Emergency Situations

If the electric parking brake cannot be deactivated because the battery is flat or there is a failure in the electrical system that Important note controls it and the vehicle needs to be moved, the emergency To release the brake completely, the wrench needs to be turned release procedure described below must be performed. 50 times, whereas it starts to be released after approximately • Take wrench A for EPB emergency release out of the tool bag. 20 turns. Warning Once the electric parking brake has been manually released, the Wrench A may only be used by specialised workshop EPB node records a failure at the next key-on and a special symbol technicians, as indicated on label C on the tool bag. and the following message are displayed on the left TFT display: “Parking Brake system revision. Go to dealer”. • Place the release wrench A in the hole B on the rear RH gravel guard and turn clockwise: this loosens the parking brake cables. Warning The parking brake resumes normal operation, but it is important to go to the nearest workshop to have it calibrated and delete any errors in the error memory. Go to a Ferrari Service Centre. Calibration is necessary for safety reasons. 5 C B Advice for Emergency Situations 221

Park Lock emergency release Warning Warning When the Park Lock safety device is deactivated manually, the vehicle may move unexpectedly. The emergency release procedure must only be carried out by specialised workshop technicians. The vehicle is only kept stationary by the parking brake, if applied. If the system cannot be released, contact the nearest Ferrari Service Centre. The Park Lock manual emergency release device is found in the engine compartment, in line with the gearbox next to the filter Warning housing, as shown by the arrow in the figure. To perform the Park Lock emergency release procedure, do the This should be avoided unless absolutely necessary: following: - to tow the vehicle; • Take wrench D out of the tool bag. - if there is a Park Lock failure (displayed on the left TFT display with the message “Only manual unlock gearbox allowed: See handbook”). Warning Wrench D may only be used by specialised workshop technicians, as indicated on label C on the tool bag. C D 222 Advice for Emergency Situations

• Open the engine compartment lid. If the electrical system allows it, check that the letter “N” appears • Extend wrench D and place it in the manual release device on the gearbox display by turning the ignition key to position II. housing keeping it bent so that it can reach the housing. The following message will appear on the left TFT display: “Gearbox not in Parking position”. At the same time, an audible signal is repeated four times to indicate that it has been released. Important note Make sure that notch G of wrench D fits onto pin H in the housing of the device. • Once the wrench has been placed in the housing, lightly press down on the filter housing to bring to wrench at right angles to the housing. • To perform the emergency release, turn wrench D counterclockwise for a quarter turn. 5 G H Advice for Emergency Situations 223

Warranty Booklet ................................................ 226 Maintenance ....................................................... 226 Level checks......................................................... 228 Wheels and tyres ................................................. 235 Maintenance of the seat belts and pretensioners ... 237 Cleaning the vehicle ............................................. 237 If the vehicle is stored for long periods .................. 241

6 CARE OF THE VEHICLE

Warranty Booklet Maintenance schedule The vehicle comes with a “Warranty Booklet”. At the intervals prescribed, the Ferrari Service Centres must This contains the vehicle’s warranty validity conditions. perform all the fine-tuning and checking operations indicated in the “Warranty Booklet”. Warning It is however advisable to report any small fault which occurs when using the vehicle (e.g. small leaks of essential fluids) to the Ferrari The warranty booklet also contains special blank spaces Service Network immediately and not wait until the next service is where the Ferrari Service Network can register the due to correct the problem. regular maintenance services performed, as indicated in the Periodic maintenance services must be performed at least once a maintenance schedule. year even if the specified mileage limit has not been reached (see “Yearly Maintenance” in the “Warranty Booklet”). Maintenance Displaying information on scheduled maintenance It is essential to always keep the vehicle in proper working order to ensure a long working life and to prevent any running defects, If the next scheduled maintenance deadline is approaching, at key- caused by negligence or lack of maintenance, and consequently to on, the message “Service Stop within:” is displayed for 5 seconds avoid hazardous situations. on the left TFT display followed by the number of kilometres or days before vehicle servicing. The information is provided in kilometres or days according to the deadline that comes first. Important note All repair work on any safety system component must be performed by the Ferrari Service Network. Service stop within: 100 km 226 Care of the vehicle

Information on scheduled maintenance can also be displayed on the left TFT display if requested by the driver irrespective of the scheduled deadlines. To do this, call up the MENU screen page (see page 98) and select “Service”. Chassis and bodywork maintenance The chassis has technological and manufacturing specifications that require that any operation be performed by staff specially trained to work with this innovative technology. It is of crucial importance to use equipment tested by Ferrari if the repair work is to be performed in accordance with rules of good workmanship. Proper execution of repair work ensures that the commercial value of the vehicle is preserved and the safety standards are complied with. Important note If the chassis is damaged in an accident, Ferrari advises customers to contact the Ferrari Service Network who will perform the necessary safety checks. The chassis, under standard conditions of use, requires no maintenance; it is however advisable to contact the Ferrari Service Network at the intervals indicated in the “Warranty Booklet“ in order to have it checked. 6 Care of the vehicle 227

Level checks Ref. Page Ref. Page A Engine oil tank cap 230 D Brake fluid tank cap 233 B Coolant tank cap 232 E Windscreen/headlight washer fluid tank cap 234 C Power steering oil tank cap 232 A D B E C 228 Care of the vehicle

Important note The level checks must be performed at the intervals indicated in the “Warranty Booklet” or, in any case, before starting a long journey. Environment All the materials used for the following operations (e.g. cloths soaked with oil or grease, pans, etc.) must be disposed of in compliance with the environmental protection regulations. Important note Only use lubricants and/or fluids recommended by Ferrari (see the “Refilling” table on page 31). 6 Care of the vehicle 229

Checking the engine oil level Important note Warning The distance between the MIN and MAX notches corresponds to approximately 2 litres of oil. The engine oil level must be checked when the engine is idling and warm and the vehicle is on level ground. DO NOT add oil with different characteristics from those of the 7. Top up if necessary with the recommended oil and make sure oil already in the engine. you do not fill beyond the MAX level on the dipstick. The symbol, shown below, on the left TFT display and the message Warning “Check engine oil level” inform the driver that the engine oil level If the oil level is below MIN, top it up and then have the system must be checked. checked by the Ferrari Service Network. 8. Screw the cap back on tightly. Proceed as follows: 1. Run the engine until the engine oil temperature has reached 90 °C (194 °F). 2. Let the engine idle. 3. Wait 2 minutes and then open the engine compartment lid and unscrew oil tank cap A. 4. Clean the dipstick on the cap. A 5. Rest cap A on the tank filler neck with the cap spring in its housing as shown in detail M. 6. Remove the cap and check that the level is between the MIN and MAX notches on the dipstick. 230 Care of the vehicle

After topping up, the “low oil level” symbol on the left TFT display Checking the DCT gearbox oil level may remain on for some time. This will allow the system to perform all the necessary checks. You should therefore consider this Important note behaviour normal. 9. When you have added or changed the oil, check the oil level We recommend that you have the oil level of the DCT gearbox once again as indicated above. checked by the Ferrari Service Network or by skilled staff. Environment Top up with due care to avoid pouring the oil out of the filler neck. M MAX MIN 6 Care of the vehicle 231

Checking the coolant level Checking the power steering system oil level Warning Warning The coolant in the cooling system reaches very high The power steering oil level must be checked with the engine temperatures and pressures. This procedure must always be warm, after having driven at least 15 km (9 mi). If it is checked performed when the ENGINE IS COLD. Never remove the cap when the engine is cold, the level may appear to be very low from the expansion tank when the engine is running or warm. even when the recommended amount of oil is in the system. • Check that the level comes up to the dotted line shown in the figure. Warning • If the level is low, remove the cap B from the expansion tank and If the oil level is below MIN, top it up and then have the system top up with the recommended coolant. checked by the Ferrari Service Network. Important note Proceed as follows: If frequent top-ups are required after short trips, have the • Remove cap C with the dipstick from the tank. system checked by the Ferrari Service Network. • Screw the cap B back on tightly. B C 232 Care of the vehicle

• Check that the power steering oil level is between the MIN and Checking the brake fluid level MAX levels on the dipstick. The brake fluid tank is located under the right-hand under- • If the level is near the MIN reference mark, top up with the windscreen protective cover. Proceed as follows: recommended oil up to the MAX level. • Remove cover P, remove cap D and check that the fluid is near the MAX mark shown in the figure. Warning Always use the indicated quantity of new, recommended fluid Important note taken from sealed containers. Clean cap D before removing it The fluid in the circuit is synthetic. The use of mineral-based fluid may irreparably damage the rubber system gaskets. • If the level is near the MIN mark shown in the figure, top up with the recommended oil to the MAX mark. • Screw the cap C back on tightly. Warning Environment Always use the indicated quantity of new, recommended fluid Do not dispose of used fluid in the environment. taken from sealed containers. D MAX 6 MAX P MIN MIN Care of the vehicle 233

Windscreen and headlight washer fluid Environment The windscreen and headlight washer fluid tank can be accessed by lifting the luggage compartment lid. Never dispose of used fluid in the environment. • Lift the cap E and fill the tank with the recommended fluid (see the “Refilling” table on page 31) until it can be seen in the fluid Warning filling manifold. • Close cap E. The fluid in the brake system may damage plastic, rubber and painted parts and is highly dangerous if it comes into contact with the eyes or the skin. If the fluid comes into contact with the eyes or skin, wash the affected part thoroughly with running water. To avoid any risk, always use protective goggles and gloves. Keep out from children's reach! Warning The use of mineral-based fluids will irreparably damage the system rubber gaskets. Do not use fluids other than those already in the system for topping up. E • Screw cap D back on tightly. 234 Care of the vehicle

Wheels and tyres Low tyre pressure can lead to overheating, internal damage and even destruction of the tyres. To ensure maximum performance and tyre life and to permit the best tyre adjustment on the wheel rim, it is important to comply with the following instructions for the first 200/300 km Warning (125 - 185 mi) with new tyres: Inflating the tyres to a pressure other than that prescribed will • avoid sudden acceleration render the TPMS monitoring system (if present) inaccurate. • avoid sharp braking and steering • drive at moderate speed on straight roads and on curves. Sudden impact with pavements, potholes and other obstacles of various types as well as long trips on rough roads can cause damage How to use the tyres to the tyres that is not always visible to the naked eye. Check the tyres regularly for any signs of damage (e.g. scratches, cuts, cracks, bulges, etc.). Important note If sharp objects penetrate the tyres, they can cause damage which is To ensure safe driving, the tyres must be kept in good condition. only visible when the tyre is removed. Have any damage inspected by an expert as it may considerably The inflation pressure must correspond to the specified values and reduce tyre life. must be checked only when the tyres are cold since tyre pressure Remember that tyres deteriorate over time even if they are rarely increases as tyre temperature increases. used or not used at all. Never reduce the pressure if the tyres are hot. Cracks in the tread and side walls, possibly accompanied by bulging, are sure signs of ageing. Environment 6 Periodically check the tyre pressure. Driving with the tyres inflated to the correct pressure helps to reduce fuel consumption. Care of the vehicle 235

Warning Warning The Ferrari Service Network has the necessary equipment for The tyres are of the “directional” type and there is an arrow tyre replacement. marked on their side wall to indicate the direction in which Have the tyres replaced by the Ferrari Service Network that they must rotate or which side is the outer side. When replaced, has the necessary equipment available to avoid causing damage maximum performance levels can only be ensured if the rotation through carelessness to the sensor located inside the wheel rim direction corresponds with the direction indicated by the arrow. (on vehicles with the tyre temperature and pressure monitoring Tyres on the same axle must always be replaced in pairs. system - TPMS). Ensure that tyres are not kept in stock for more than 4 years. Regularly check the tyre tread (minimum acceptable depth The maximum limit for keeping tyres in stock is 4 years 1.7 mm). As the tread wear increases, there is a greater risk of provided they are kept away from sunlight, bad weather and skidding. damp and where there is a low oxygen content. Warning Important note Drive carefully on wet roads to reduce the risk of “aquaplaning”. The Ferrari Service Network can certify whether aged tyres are suitable for use. In any case, tyres that have been on a Wheel alignment check and adjustment vehicle for more than 3 years must be checked by a Ferrari When you notice unusual wear of the tyres and in any case, at the Service Centre. intervals prescribed in the “Warranty Booklet”, have the Ferrari Service Network check the wheel toe-in and camber. Warning We recommend replacing tyres every 4 years under normal use. Frequent use in maximum load conditions and at high temperatures may accelerate ageing. Never fit tyres of uncertain origin. 236 Care of the vehicle

Maintenance of seat belts and pretensioners Cleaning the vehicle • Periodically check that the screws on the anchor points are tight Cleaning the exterior and that the seat belt is in perfect condition and slides smoothly. • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. Environment • To clean the seat belt, wash it by hand with mild soap and water, All the materials used for the following operations (e.g. cloths rinse it and let it dry. Do not use strong detergents, bleach or soaked with oil or grease, pans, etc.) must be disposed of in aggressive solvents, as they can weaken the fibres. compliance with the environmental protection regulations. • Do not let the seat belt retractors get wet: proper functioning is only ensured if they are kept dry. Proper care of the vehicle on the part of the owner is essential for • The pretensioner requires no maintenance or lubrication. If the vehicle long life. immersed in water or mud, the pretensioner must necessarily be Here is a list of the main precautions to be taken. replaced. • Certain parts of the vehicle should not be left wet or dirty for • The pretensioner must be replaced at the intervals indicated in long periods of time: in particular, the passenger compartment the “Warranty Booklet”. floor and the luggage compartment must always be kept clean and dry. The drain holes under the doors should be kept unclogged to allow any water to drain. • The underbody and the lower surfaces of the vehicle should be cleaned regularly, and more frequently (at least once a week) if the vehicle is used on salty or rough roads. The vehicle should be cleaned thoroughly and carefully: cleaning that merely wets encrusted mud without removing it completely can prove 6 damaging. • The vehicle must be washed regularly with suitable equipment. Do not use very hot water or steam to clean the paintwork and the lower surfaces. It is advisable to soften any dirt first, then remove it with a jet of water at room temperature. Care of the vehicle 237

Cleaning and care of matt paintwork (optional) Important note Do not use aggressive products for cleaning the windows. Warning The use of aggressive products could seriously damage the The paintwork MUST NOT be polished using any type of bodywork. product. • Do not wash the vehicle in direct sunlight or when the bodywork Owners must take great care of vehicles with matt paintwork is still warm: make sure that the jet of water does not blast the (optional). paintwork; wash the vehicle with a sponge and a mild soap and Here is a list of the main precautions to be taken. water solution; rinse the vehicle again with a jet of water and dry it with a chamois leather. • Wash the vehicle using a steam cleaner and rinse with demineralised water only. Important note • It must be dried using an automatic dryer or compressed air. Manual drying can ONLY be performed using a clean 3M When the vehicle has been washed, apply slight pressure to the microfibre yellow cloth that has been soaked in demineralised brake pedal at moderate speed before driving at a normal speed, water in the areas where limescale deposits are present. The cloth until the brake discs and pads have cleaned off. must be kept in a special clean container. • To clean any grease or oil marks, a clean 3M microfibre yellow In order to maintain the shine on the paintwork, polish it once or cloth soaked in R107/S solvent (heptane) can be used. A new twice a year with products recommended by Ferrari. cloth must be used and it must not have been previously soaked • Any areas that are cracked or chipped by stones, scratches or in demineralised water. parking manoeuvres, etc., must be immediately repaired by the • Do not wash the car in direct sunlight. Ferrari Service Network. • Wash the vehicle only when the bodywork and engine are cold. • Do not park the vehicle in damp and/or unventilated areas for • Do not apply stickers to the bodywork. long periods of time. 238 Care of the vehicle

• Any areas that are cracked or chipped by stones, scratches or parking manoeuvres, etc., must be immediately repaired by the Important note Ferrari Service Network. Avoid the film coming into contact with the brake fluid: the film will become opaque. Important note DO NOT lean against the vehicle especially if you are wearing • Do not use solvents along the edges of the film to them from clothes with buttons, buckles or are wearing rings, necklaces, penetrating inside the adhesive layer. etc. This may cause irreparable damage to the bodywork. Important note Important note Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Light Blue, Met Sky-Blue and Fuji White vehicles must be To use suitable products, contact the Ferrari Service Network. washed every month and waxed at least twice a year so that dirt, acid rain, pollutants, etc. do not penetrate the pores of the film and cause it to tarnish. Cleaning of protective antistone-chipping film (optional) The film has been designed to protect the bodywork: anything that Important note damages the paint will also damage the film. We recommend that the film be replaced every 24 months for Warning Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Light Blue, Met Sky-Blue and Fuji White vehicles, which may Do not pour denatured ethyl alcohol, acetone, isopropyl alcohol, heptane or substances that contain these compounds on the show a light visible tarnish due to dirt inside the pores of the film. 6 film. It should be noted that timely and accurate cleaning (monthly • Do not apply adhesive elements on the film. washing and waxing twice a year at least) will prevent deterioration • When cleaning, do not use metal or abrasive substances in general of the film. and acid chemical compounds. Care of the vehicle 239

Cleaning the interior Cleaning and care of the Alcantara® upholstery Cleaning and care of the leather upholstery Warning As indicated in the “Maintenance Schedule” (see the “Warranty Do not use steam cleaners. Booklet”), proper and regular treatment, at least once a year, will help preserve the quality, natural characteristics and softness of the leather upholstery in your Ferrari. • Carefully dust the parts to be cleaned With this in mind, specific leather care products are also available • Use a soft cloth or sponge moistened with clean water (“Cleaner” and “Cream”) both tested by Ferrari. • Thoroughly wring out the cloth and wipe it over the entire These products can be ordered through the Ferrari Spare Parts Alcantara® area making sure you do not overwet it Service Department, both individually and as part of the “Care • Repeat the procedure Kit” which includes the complete range of products for cleaning the • Let it dry completely vehicle. • To recondition the material, gently use a brush with soft bristles. Important note For use of the “Care Kit” products, contact the Ferrari Service Network. The following products must be avoided when cleaning the leather: harsh detergents, turpentine, liquid stain removers, petrol, solvents and domestic cleaning products. All of these products damage the natural material. 240 Care of the vehicle

If the vehicle is stored for long periods If the vehicle is not used for long periods of time, certain precautions should be taken: • if possible, park the vehicle on a level surface in a covered and well-ventilated area • prevent the vehicle from moving by engaging a gear • bring the tyre pressure to 3.0 bar (43.51 psi) and periodically change the point where the tyres rest on the ground • connect the battery conditioner Important note If you do not want to connect the battery to the battery conditioner in order to keep certain devices functioning such as radio station memory, alarm system, etc., the battery must be recharged at least once a month. If the vehicle is not used for long periods of time without connecting the battery conditioner, the battery must be recharged at least every three months. • protect the vehicle with a breathable fabric cover and avoid materials that prevent any dampness on the bodywork from evaporating. Before using the vehicle again after long periods of inactivity, adjust 6 the tyre pressure to the indicated pressure and check the fluid levels of all the systems. Care of the vehicle 241

Glossary .............................................................. 245

7 GLOSSARY

Abbreviation Meaning ABS (Anti-lock Braking System) The ABS prevents wheel locking when braking so that vehicle handling can be maintained. AC Air conditioning. ASR (Antriebs Schlupf Regelung) Anti-skid regulation during acceleration. Auto easy exit Simplified function gear shifting. To exit “Auto easy exit” mode, simply operate one of the two shift paddles. Autopark Automatic activation of the electric parking brake (EPB) when the engine is switched off. This function can be disabled. AVH Automatic Vehicle Holding Additional function of the electric parking brake (EPB): it allows gradual release of brake shoes/pads when the vehicle starts up. This guarantees an optimised release for the vehicle and is an aid for the driver. DCT Dual Clutch Transmission Each clutch is associated with a part of the gearbox, one is designed for engaging even gears, the other for odd gears. Once a gear has been engaged, the system has already preselected the next one. After reaching the correct RPM, a clutch opens and at the same time the other one closes, so that the traction force is not interrupted. Disposal The procedure laid down in Directive 2000/53/EC and the implementation standard. EBD (Electronic Brake-Force Distribution) Electronically-controlled brake-force distribution. ECU Electronic Control Unit. E-Diff 3 Evolved electronic differential integrated with the F1-Trac traction control. EPB Electric Parking Brake: the system operates by means of an ECU and an electric motor on the rear brake shoes. ESC Electronic Stability Control Consists of two systems: VDC and F1-Trac. 7 Glossary 245

Abbreviation Meaning F1-Trac Traction control derived from the technologies used in the racing sector. The system can estimate the maximum available grip in advance by continuously monitoring the relative wheel speed and using an auto-adaptive operating logic. Comparing this information with the vehicle dynamics model stored in the control system, F1-Trac, optimises the vehicle behaviour by controlling engine torque delivery. FBP (Ferrari Brake Prefill) System that eliminates the distance between the brake pads and discs by applying slight pressure to the braking system as soon as the accelerator pedal is released just before braking. This results in more immediate brake response. Homologation The procedure laid down in Directive 2007/46/EC and the implementation standard. Launch Control Strategy for performance standing starts. Manettino The driving mode control switch on the steering wheel that allows the driver to use vehicle potential in a quick, intuitive way. Park Lock Automatic DCT gearbox park lock. When the engine is off, a mechanical lock is automatically activated to prevent the vehicle from moving if the electric parking brake is not activated. TFT displays Multifunction colour displays on the instrument panel that provide vehicle information. TPMS Tyre Pressure Monitoring System (optional). Using special sensors fitted inside the wheel rims next to the air valve, the data measured is sent to an ECU. The data and messages are displayed on the left TFT display. Traction power Force exerted by the vehicle on the road surface through the wheels; it indicates the grip. VDC Vehicle Dynamic Control performed through the braking system and engine torque. Xenon headlights Headlights on the front of the vehicle that produce a more intense beam by using a voltaic arc rather than an incandescent spiral. 246 Glossary

7 Glossary 247

Table of Contents ................................................ 250

8 TABLE OF CONTENTS

Index Auto easy exit ............................................................................... 149 Auxiliary Occupant Protection Systems .............................. 62 AVH function ........................................................................ 75, 162 B Symbols Backrest and seat cushion side width adjustment ........ 177 12V power socket ...................................................................... 189 Basic seat ........................................................................................ 175 Battery ............................................................................................. 212 A Battery conditioner .................................................................... 216 “Automatic gearbox” mode .................................................... 149 Before a trip .................................................................................. 143 “Auto easy exit” mode ............................................................... 149 Brake fluid ..................................................................................... 233 Abbreviations .................................................................................... 9 ABS ..................................................................................................... 72 C Activation of electronic alarm .................................................. 17 Capless filler neck ......................................................................... 91 Active safety .................................................................................... 55 Carwash ......................................................................................... 163 Adaptive headlights ................................................................... 136 Carwash procedure ................................................................... 163 Adjusting display brightness .................................................... 99 Checking the battery ................................................................. 212 Adjusting the air vents ............................................................. 186 Chronometer ................................................................................ 103 Adjusting the steering wheel ................................................. 181 Chronometer operating ........................................................... 103 AFS2 ................................................................................................. 136 Chronometer screen page ...................................................... 103 Air conditioning and heating system ................................ 183 Cleaning and care of the Alcantara upholstery .............. 240 Air conditioning controls ....................................................... 183 Cleaning and care of the leather upholstery ................... 240 Air recirculation ........................................................................... 185 Cleaning the exterior ................................................................ 237 Alarm memory ................................................................................ 19 Cleaning the interior ................................................................. 240 Alarm system ................................................................................... 15 Cleaning the parking sensors ................................................ 111 Automatic gearbox ..................................................................... 149 Cleaning the vehicle .................................................................. 237 Automatic Vehicle Holding ............................................. 75, 162 Closing the engine compartment lid .................................... 86 Autopark Function .............................................................. 75, 162 250 Table of Contents

Closing the fuel filler flap ......................................................... 90 DOWN-shifting due to underrevving ................................ 147 Closing the hard top .................................................................. 141 Driver-side power window ....................................................... 92 Closing the luggage compartment lid .................................. 88 Driver’s seat position memory ............................................... 178 Clutch overheat alarm devices .............................................. 218 Driver and passenger airbags .................................................. 63 Collapsible spare wheel .......................................................... 208 Driver and passenger airbag operating ............................... 64 Configuration of vehicle parameters .................................... 98 Drive Away function .................................................................. 161 Consulting the manual .................................................................. 8 Driving at night ............................................................................ 151 Consumption .................................................................................. 27 Driving in fog ............................................................................... 152 Controls on the steering wheel ............................................ 126 Driving in the rain ...................................................................... 151 Controls overview ......................................................................... 37 Driving on mountain roads .................................................... 152 Coolant ............................................................................................ 232 Driving on snowy or icy roads .............................................. 152 CT OFF mode .................................................................... 127, 157 Driving style .................................................................................... 10 Driving the vehicle ............................................................. 46, 143 D Driving using the driving mode control switch “Doors, engine or luggage compartment lid open” (“Manettino”) ............................................................................... 155 function display ........................................................................... 115 Driving with the “ABS” braking system ............................ 153 “DOWN” shift paddle ............................................................... 129 Duplicating the keys .................................................................... 16 Day lights ........................................................................................ 134 E DCT gearbox oil .......................................................................... 231 Deactivating the anti-lift alarm ................................................ 18 “ESCAPE” function ................................................................... 113 Deactivation of electronic alarm ............................................. 18 E-Diff 3 ............................................................................................. 74 Deformable body .......................................................................... 54 EBD .................................................................................................... 72 Dimensions ...................................................................................... 26 Electrically-adjustable seat ...................................................... 177 Disconnecting the battery ....................................................... 212 Electrical system ............................................................................ 27 Display setting ................................................................................ 98 Electric parking brake ....................................................... 75, 161 Dome light ..................................................................................... 137 Electronic alarm ............................................................................ 17 Doors .......................................................................................... 36, 84 DOWN-shifting .................................................................... 49, 147 Electronic Stability Control ...................................................... 73 Emergency opening of fuel filler flap .................................. 90 8 Table of Contents 251

Emergency opening of luggage compartment lid ........... 88 Flashing the headlights .................................................... 44, 132 Emergency release of the electric parking brake Follow me home .......................................................................... 136 (EPB) ............................................................................................... 220 Front Lift ........................................................................................ 165 Emergency starting .................................................................... 214 Front parking sensors (activation/deactivation) ........... 137 Emergency tyre repair and inflation kit ........................... 194 Fuel filler flap and neck ............................................................. 90 Emissions .......................................................................................... 27 Fuel filler neck ............................................................................... 90 Engaged gear display ................................................................ 123 Fuel inertia switch .............................................................. 71, 211 Engine compartment lid ............................................................ 86 Fuel level ........................................................................................ 100 Engine malfunction alarm devices ...................................... 219 Fuel level gauge ........................................................................... 100 Engine oil ....................................................................................... 230 Fuses ................................................................................................. 200 Engine RPM LED on steering wheel ................................. 122 ENGINE START ......................................................................... 126 G Environmental protection ......................................................... 10 Gearbox display ........................................................................... 122 EPB - Electric parking brake ......................................... 75, 161 Gear engaged ............................................................................... 123 ESC ..................................................................................................... 73 General remarks ............................................................................... 4 ESC OFF mode ................................................................. 127, 157 Glossary .......................................................................................... 245 Exhaust system overheating alarm devices ...................... 217 Glove compartment .................................................................... 187 External lights ................................................................................ 44 External rear-view mirrors ..................................................... 182 H F Hard top operating system failure ....................................... 142 Hazard warning lights ...................................................... 45, 135 “Follow me home” function ................................................... 136 Headlight washer ........................................................................ 130 “Front Lift” system ..................................................................... 165 High beams ........................................................................... 44, 132 F1-Trac ............................................................................................... 74 Horn ................................................................................................. 128 Failure of turn indicators and running lights ................. 114 Horn control ................................................................................. 128 Fault display .................................................................................. 113 How to fasten seat belts ............................................................. 58 FBP - Ferrari Brake Prefill ......................................................... 73 How to use the tyres ................................................................. 235 Ferrari CODE system ............................................................... 15 252 Table of Contents

I Locking and opening the doors from the inside .... 36, 84 Low tyre pressure ......................................................................... 77 Identification and homologation plates and labels ........ 20 Luggage compartment lid ......................................................... 87 If the vehicle is stored for long periods ............................ 241 Lumbar support adjustment .................................................. 177 Ignition switch ....................................................................... 43, 89 Indication of AVH system activated .................................... 124 M Indication of Launch Control activated ............................ 124 Infotainment system .................................................................. 125 “Manettino” driving mode control switch ....................... 127 Instruments and gauges ............................................................. 94 MAIN ................................................................................................. 96 Internal rear-view mirror ......................................................... 181 Maintenance .................................................................................. 226 Interrupting the hard top opening/closing cycle .......... 142 Maintenance of seat belts and pretensioners .................... 60 Maintenance schedule .............................................................. 226 K Main engine specifications ........................................................ 27 MAIN screen page ........................................................................ 96 Key-on ............................................................................................... 89 Manettino ............................................................................. 127, 155 Key codes ......................................................................................... 14 Manettino status ......................................................................... 106 Key lock .................................................................................... 43, 89 Manettino status screen page ............................................... 106 Matt paintwork ............................................................................. 238 L MENU ............................................................................................... 98 LAUNCH button ....................................................................... 164 MENU screen page ...................................................................... 98 Launch Control .......................................................................... 164 Ministerial homologation .......................................................... 19 Leather upholstery ..................................................................... 240 Left TFT display ............................................................................ 96 N Left TFT display symbols ....................................................... 116 “N” (Neutral) ................................................................................ 148 Level checks .................................................................................. 228 “N” request ............................................................................ 49, 148 Lighting ........................................................................................... 132 Neutral ..................................................................................... 49, 148 Light bulbs ................................................................................... 199 Light switch ........................................................................... 44, 132 LOCK/UNLOCK ....................................................................... 137 8 Table of Contents 253

O R OK button ........................................................................................ 96 “Rear Parking Camera” screen page ................................... 126 Opening doors ............................................................................... 36 RACE mode ........................................................................ 127, 156 Opening doors from the outside ........................................... 84 Rain sensor .................................................................................... 131 Opening the engine compartment lid .................................. 86 Rain sensor failure ...................................................................... 131 Opening the fuel filler flap ....................................................... 90 Rear-view mirrors ............................................................... 41, 181 Opening the hard top ............................................................... 140 Rear fog lights ...................................................................... 45, 135 Opening the luggage compartment lid ................................ 87 Rear Parking Camera ................................................................. 126 OPEN button ............................................................................... 187 Rear shelf ...................................................................................... 189 Reconnecting the battery ........................................................ 213 P Refilling ............................................................................................. 31 Remote control batteries ........................................................... 17 “Parking” mode ........................................................................... 123 Replacing a fuse .......................................................................... 200 Parking lights ................................................................................ 133 Replacing a wheel ...................................................................... 208 Parking sensors ........................................................................... 109 Replacing light bulbs ................................................................ 197 Parking sensor failure ............................................................... 112 Replacing remote control batteries ....................................... 17 Park Lock ...................................................................................... 163 Replacing the brake pads and discs .................................... 220 Park Lock emergency release ................................................ 222 Retractable hard top .................................................................. 138 Passenger-side power window ................................................ 92 Right TFT display ....................................................................... 124 Passenger compartment accessories .................................... 187 Roof panel controls .................................................................... 137 Passive safety ................................................................................... 54 Running-in ..................................................................................... 143 Performance .................................................................................... 27 Run Flat tyres ................................................................................. 30 Performance start ....................................................................... 164 Pocket-change compartments ............................................... 188 S Power steering .............................................................................. 153 Power steering system oil ........................................................ 232 “Slow Down” function .............................................................. 217 Power windows .............................................................................. 92 “Speedometer” screen page ................................................... 125 Pretensioners .................................................................................. 60 “Speed limit exceeded” message ........................................ 108 Push start ........................................................................................ 149 “Stop and Go” function .......................................................... 109 254 Table of Contents

Safe driving ................................................................................... 150 Super Racing seat ...................................................................... 180 Satellite Alarm System ................................................................ 19 Suspension damping control ................................................. 154 Seats ......................................................................................... 39, 175 Suspension damping delink button ......................... 128, 159 Seat adjustment ................................................................... 39, 175 Switching off the engine .................................................. 49, 148 Seat belts ................................................................................... 42, 56 System start-up ............................................................................ 144 Seat heating ................................................................................... 179 Sequential downshifting .......................................................... 147 T Service .................................................................................................. 8 Tilting the backrest .................................................................... 176 SETUP ............................................................................................... 96 Toolkit ............................................................................................. 192 Side airbags ..................................................................................... 68 Tool bag ......................................................................................... 192 Side airbag operating .................................................................. 68 Towing ............................................................................................. 210 Spare parts .......................................................................................... 7 Tow hook ........................................................................................ 210 Special recommendations ......................................................... 52 TPMS ................................................................................................. 76 Speedometer ................................................................................. 125 TPMS failure ................................................................................... 81 Speedometer display ................................................................. 125 TPMS inactive ................................................................................ 81 Speed limit setting ..................................................................... 108 TPMS not calibrated ................................................................... 80 SPORT 2 screen page ............................................................... 101 TPMS temporarily inactive ....................................................... 81 SPORT mode ..................................................................... 127, 155 Transmission ratios ....................................................................... 27 SPORT screen page ................................................................... 101 TRIP ................................................................................................... 96 Starting the engine .............................................................. 47, 145 TRIP A/B ....................................................................................... 107 Starting the vehicle ............................................................ 48, 146 TRIP A and TRIP B screen pages ....................................... 107 Start button ................................................................................... 126 Turn indicators ..................................................................... 45, 134 State of vehicle ............................................................................ 104 Twilight sensor ............................................................................. 134 STATUS ............................................................................................. 96 Tyres ................................................................................................... 28 Steering wheel ..................................................................... 40, 181 TYRES screen page .................................................................. 102 Stop&Start failure ....................................................................... 173 Tyre pressure .................................................................................. 28 Stop&Start system (optional) ................................................ 167 Stopping the vehicle .......................................................... 49, 148 Tyre puncture ................................................................................. 78 Tyre temperature and pressure monitoring system ....... 76 8 Sun visors ...................................................................................... 188 Table of Contents 255

U Windscreen washer/wiper lever ........................................... 129 Winter tyres ..................................................................................... 28 “UP” shift paddle ........................................................................ 129 Unfastening the seat belts ......................................................... 59 UP, DOWN, LEFT, RIGHT buttons ..................................... 96 UP-shifting ............................................................................. 49, 147 UP-shifting due to overrevving ............................................ 147 Use of the vehicle ......................................................................... 10 V VDA .......................................................................................... 96, 102 Vehicle Dynamic Assistance ................................................... 102 Vehicle keys ..................................................................................... 14 Vehicle status screen page ...................................................... 104 W “Warning: danger of ice” message ...................................... 108 Warming up the engine .................................................... 48, 146 Warning lights on the panel ................................................... 116 Warranty Booklet ................................................................... 7, 226 Weights .............................................................................................. 26 WET mode .......................................................................... 127, 155 Wheel alignment check and adjustment ........................... 236 Wheel rims ....................................................................................... 28 While travelling ............................................................................ 150 Windscreen and headlight washer fluid ........................... 234 Windscreen washer .................................................................... 130 Windscreen washer/wiper ...................................................... 129 256 Table of Contents

Customer Service Customer Service Roadside Assistance and Recovery Service email: [email protected] web site: www.ferrari.com Through its Customer Care Service, available at the numbers below, Ferrari can offer its customers information on the cars in its range Country  toll-free number and the special services it provides. Austria 0800281620 The Roadside Assistance and Recovery Service, which can be Belgium 080071863 contacted 24 hours a day, 7 days a week, is available to all owners of new cars and used cars that are part of the “Ferrari Approved” Denmark 80886196 certified used vehicle programme for the entire period covered by Finland 0800114003 the warranty. The Service is only available in the countries listed in France 0800910117 the table. Germany 08001819802 Greece 800391292616 Ireland 1800553946 Italy 800080202 Luxembourg 80025354 Norway 80015619 Netherlands 08000221803 Monaco 80093260 Portugal 800839124 Spain 900976931 Sweden 020796196 Switzerland 0800564730 United Kingdom 08082343324 Japan 0120325408 Rest of world +39 (0) 536 949111

Roadside Assistance and Recovery Service Country registered Toll-free number From abroad Austria Germany 0800 100 8213 +49 895 598 7613 Czech Republic Slovakia 800 221 220 +42 02 2158 6628 Belgium Luxembourg Netherlands 0800 309 03 +32 2533 7984 France Monaco 0810 808 082 +33 1 4185 9288 Denmark +46 8 5010 2493 Finland +46 8 5010 2494 Norway +46 8 5010 2492 Sweden 0800 3588 550 +46 8 5010 2491 United Kingdom 0800 3588 550 +44 8707 375 984 +44 1444 442 081 Greece Turkey 800 1133 900 +30 210 3422 013 Italy Republic of San Marino Vatican City 800 771 811 +39 02 9377 6774

Spain Andorra 900 205520 +34 91 5149 985 Portugal 800 200 113 +351 21 3835 528 Switzerland Liechtenstein 0800 888 022 +41 22 3406 831 Slovenia 080 2151 +386 158 830 25 Hungary 06 80 204 873 +36 1 4654 676 Romania 0313 223 223 +36 1 4654 618 Russia 8 800 200 1123 +7 (495) 589 1125 China 400 810 1153 - Japan 0120 688 801 -

Equipment and options in Ferrari vehicle models may vary because of specific legal and market requirements. The information contained in this publication is therefore not binding in any way. Ferrari reserves the right to make any modification to the vehicle models described in this manual, at any time, for either technical or commercial reasons. Contact the nearest Ferrari Dealer for any further information you may require. Code no. 84063400 In the interests of efficiency and safety, as well as to preserve the value of the vehicle, we do not recommend modifying Catalogue no. 3849/11 the equipment using non-approved parts. EDITION 1st edition October 2011 EDITING STAR s.r.l. Alessandria - Italia PRINTING STAR s.r.l. Alessandria - Italia Technical Service Department Via Abetone Inferiore, 4 41053 Maranello Modena - Italia