Ferrari 458 Italia Owners Manual

Thursday, August 31, 2017
Download

Owner's Manual U.S. and Canada Version Model Year 2010

General notes - Driving takes place in a naturally dangerous context where a number of different risk factors interact. For this reason, it is This vehicle, which complies with the NHTSA / EPA important to drive bearing in mind that others, whether they certification standards, uses advanced technology and is are pedestrians, motorcyclists or motorists, can make mistakes. capable of achieving high performance levels. Keeping a safe distance helps you reacting in emergency situations. It is equipped with sophisticated active and passive safety Distractions and underestimating danger are the cause of systems (described below); these features and systems do not most accidents. authorize the driver to take risks other than those involved - Caution and discipline are the basis of safe driving. Correct in normal driving, since the preventive and protective action and careful use of a vehicle derives from respect for one's of these devices is provided only in certain conditions. Unless own safety and that of others, as well as from compliance otherwise instructed specifically by Ferrari (see the Safety with road regulations. chapter), the deactivation of any vehicle restraint systems is PROHIBITED. Ferrari recommends reasonable and careful use of the While certain safety devices (e.g., the airbags) have been vehicle. The driver MUST NEVER allow passengers to designed to help ensure that they provide optimal levels of increase the risks associated with driving (e.g., by not using protection, they may nonetheless be hazardous in the event of safety systems such as the seat belts) by failing to observe failure by the driver or passenger to observe the instructions the mandatory safety rules that apply to both driver and given by Ferrari. All vehicle occupants must be attentive at passengers. All occupants must wear their seat belts at all all times and take particular care when transporting passengers times! who are more subject to injury, such as children, disabled and elderly persons. The vehicle MUST NOT be modified or tampered with for any reason whatsoever since, by so doing, the manufacturer's For safe driving, the following conditions must ALWAYS be met: homologation and safety parameters will be modified. - the driver must be in excellent condition The owner of the vehicle is obliged to perform careful - road regulations must be strictly observed maintenance on the vehicle in compliance with the - common rules of caution must always be observed in relation recommended maintenance schedule. to the quality/performance of the vehicle, driving conditions and contingent situations. 4 Introduction

The driver must pay particular attention to the signals of Remember that state, national and international legislation the vehicle, especially the warning lights on the dashboard reguires that the driver of the vehicle must be capable of and buzzers. Even when the warning lights do not indicate a performing corrective and/or emergency maneuvers at all situation of immediate danger, the driver must be cautious in times. The driver must also use any on-board information, relation to possible consequences/degeneration of the failure communication and entertainment systems responsibly, and other information given. especially when the vehicle is in motion. Examples of Even during routine operations, such as refueling, precautions information, communication and entertainment systems are should always been taken and it is important to check that the following: satellite navigation systems, traffic information flammable liquid has not been spilled; these precautions must systems, media players (e.g., iPod), telephones with Bluetooth be observed even if the operation is performed by others. connectivity, etc. (whether audio-based or with display). Similarly, before starting off make sure that the doors are closed by checking the warning lights and also manually. The driver must bear in mind that on-board systems may cause The driver must be fully knowledgeable with the vehicle distraction while driving, since they may require the driver to and its controls in order to handle and drive it correctly. turn his attention away from the road for several seconds. Knowledge of the vehicle can be achieved/improved by Aftermarket video entertainment systems for the passenger attending the driving courses held by Ferrari which are (e.g., TV) must be installed only where they will not distract recommended. the driver while the vehicle is in motion. The use of motor sports terms (such as F1, SPORT and RACE) These systems may only be operated by the driver: is merely indicative of the competition-derived technology - in complete safety (stopping the vehicle before use if and suspension systems in the vehicle and does not endorse necessary); inappropriate behavior on the road which does not comply - putting road safety first; for example, in poor or limited with traffic regulations. visibility conditions, looking at a display with active programs can be distracting even if you take your eye off the road, The above is a general outline of some of the issues described even for a split second. in detail in this manual. - while the vehicle is in motion, the attention required to use on-board systems must never exceed the high level of attention required to drive safely in accordance with the traffic regulations; Introduction 5

- if the previous vehicle owner had installed systems on the THE NHTSA’S TOLL-FREE AUTO SAFETY HOTLINE vehicle that are NOT APPROVED by Ferrari (e.g., car If you believe that your vehicle has a defect which could cause a tuning), ensure that they are fully compatible with the crash or could cause injury or death, you should immediately inform original vehicle equipment; the National Highway Traffic Safety Administration (NHTSA) in - in some countries, the use of entertainment/information addition to notifying Ferrari S.p.A. systems on vehicles is prohibited while driving. If NHTSA receives similar complaints, it may open an investigation, - the driver is responsible for the use of these entertainment/ and if it finds that a safety defect exists in a group of vehicles, it information systems with video screens if they are prohibited may order a recall and remedy campaign. However, NHTSA cannot in the country where the vehicle is driven. become involved in individual problems between you, your dealer, - strict priority criteria must be observed when driving a or Ferrari S.p.A. vehicle: you must not therefore take your attention and To contact NHTSA, you may call the Vehicle Safety Hotline toll-free eyes off the road. Operations not involved with driving at 1-888-327-4236 (TTY: 1-800-424-9153) (Media inquires: 202- (e.g., changing dashboard functions) must be performed in 366-9550); maximum safety when the vehicle is stationary. go to http://www.safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE West Building, Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. THE TRANSPORT CANADA TOLL-FREE AUTO SAFETY HOTLINE If the affected vehicle is not repaired free of charge to you and within a reasonable time, you may submit a written complaint to Head of Recalls, Road Safety and Motor Vehicle Regulation, Transport Canada, 2780 Sheffield Road, Ottawa, Ontario KIB 3V9. You may also telephone Transport Canada at (613) 993-9851. 6 Introduction

FUELS CONTAINING ALCOHOL For its fuel injection systems, Ferrari uses components and materials of very high quality. However, no specific tests have been carried out to assure the reliability of the system when using fuel containing alcohol. Consequently, we recommend that you do not use fuel containing alcohol on Ferrari vehicles. Introduction 7

Introduction Warranty Book The aim of this Owner’s Manual is to inform you in the proper Each new vehicle comes equipped with a “Warranty Book”. use of your vehicle, to help you get the best value from your This contains the vehicle’s warranty terms and conditions. vehicle and to provide information on routine maintenance: we The Warranty Book also contains the routine maintenance advise you to read it carefully before setting out. The Owner’s indicated in the “Maintenance Schedule”. Manual should be considered an integral part of the vehicle and must therefore always be kept on board. Using the vehicle in a way that does NOT comply with the Owner's Manual not only exonerates Ferrari of any Service responsibility but also puts the operator and passenger at great The information in this manual is necessary for the proper risk. use and care of the vehicle. In addition, Customers will get maximum satisfaction and results from the vehicle if they Updating carefully follow the instructions contained in it. We recommend that you have all the checks and services The high quality level of the vehicle is subject to constant performed at an Authorized Ferrari Dealer since they have technological improvements. Therefore, there may be highly skilled staff and the necessary equipment. differences between this manual and your vehicle. Please refer to the “Sales and Service Organization” manual Your Authorized Ferrari Dealer will be pleased to provide for information on the location of the Authorized Ferrari you with all the information on any important updates. Dealers. All specifications and illustrations contained in this manual The Ferrari Technical Service Department is at your refer to those resulting as of the printing date. Specifications complete disposal for any information and advice. may be changed without prior notice. Spare parts When replacing parts or topping up with lubricants and fluids, we recommend that you use original spare parts and the lubricants and fluids recommended by Ferrari. The Ferrari warranty is voided if Genuine Ferrari Spare parts are NOT used for repairs. 8 Introduction

Consulting the manual Within the various sections, special attention must be paid to the parts marked as follows: To facilitate reading the manual, the topics have been divided into sections and chapters. To further facilitate consultation, each section is identified by a specific color: Warning Extreme caution required: failure to comply with the 1. General instructions could constitute a serious risk to personal safety Provides general information about your vehicle. and vehicle protection! 2. Quick reference guide Contains all information you need when using the vehicle for Important note the first time. Important note: a note containing instructions or information. 3. Safety Describes the main safety systems in the vehicle. 4. About your vehicle Environment Provides necessary information for use of the vehicle. Warning for environmental protection: useful advice for 5. Advice for Emergency Situations protection of the environment. Provides useful advice for solving certain problems that may occur. 6. Care of the vehicle Provides advice for cleaning, care and routine maintenance of your vehicle. 7. Glossary Explains the main technical concepts. 8. Table of Contents Allows you to quickly identify and locate the information required. Introduction 9

Abbreviations/Acronyms Some descriptions and terms with particular meanings are found in this manual in an abbreviated form: AC Air conditioning ABS Anti-lock Braking System ASR Anti-skid Regulation during acceleration CST Stability and Traction control DCT Dual Clutch Transmission EBD Electronic Brake-force Distribution ECU Electronic Control Unit F1-Trac Traction control derived from the technologies used in the racing sector PS Performance Start For an overview of the abbreviations contained in this manual, please see the Glossary. 10 Introduction

Environmental protection Driving style - Do not accelerate during the starting procedure. Environment - Do not warm up the engine when the vehicle is stationary. - Drive carefully and keep a safe distance suited to the driving The following chapter contains useful advice for environmental speed. protection. - Avoid sharp and frequent accelerations. - Turn off the engine if the vehicle is kept stationary for long Ferrari has designed and constructed a vehicle using technologies, periods of time. materials and devices capable of reducing the harmful impact on the environment to a minimum. - Shift gears using only 2/3 of the speed permitted for each gear. If you use your vehicle with respect for the environment, you too will contribute towards environmental protection. Important note Fuel consumption as well as engine, gearbox, brakes and tires wear The vehicle is equipped with exhaust gas control and mainly depend on two factors: monitoring systems which must always function properly and be - use of the vehicle checked regularly. - driving style. Both factors are influenced by the driver. Warning Engine exhaust, some of its constituents, and certain vehicle Use of the vehicle components contain or emit chemicals known to the State of California - Avoid using the vehicle for short trips. (CA) to cause cancer and birth defects and reproductive harm. - Check that the tire pressure is correct. In addition, certain fluids contained in vehicles and certain products - Proper periodic maintenance will contribute to preserving of component wear contain or emit chemicals known to the State of your vehicle in full working order and will help protect the California (CA) to cause cancer and birth defects or other reproductive environment. harm. We therefore advise you to respect the service due dates indicated Battery posts, terminals and related accessories contain lead and lead in the “Maintenance Schedule”. compounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with soap and water. Introduction 11

Vehicle event data The driving and safety systems employed in your vehicle use com- puters that monitor, and share with each other, information about your vehicle operation. One or more of these computers may store certain monitored information, either during normal vehicle opera- tion or in a crash or near- crash event. Stored information may be read and used by: • Ferrari North America, Inc. • Ferrari S.p.A. • Service and repair facilities • Law enforcement or government agencies • Others who may assert a legal right to know, or who obtain your consent to know such information. 12 Introduction

Vehicle keys ........................................................... 16 Alarm system......................................................... 17 Duplicating the keys .............................................. 18 Replacing remote control batteries ......................... 19 Electronic alarm .................................................... 19 Identification and homologation plates and labels .. 22 Dimensions and weights ........................................ 28 Main engine specifications ..................................... 29 Performance.......................................................... 29 Fuel consumption .................................................. 30 Wheel rims and tires .............................................. 31 Recommended lubricants and fluids ....................... 34

1 GENERAL

Vehicle keys Important note The vehicle is delivered with two identical keys that can be used for: Make sure you record the code numbers in the space provided in the “Warranty Book”. - central door locking / unlocking - starting the vehicle Key codes - activating/deactivating the alarm system - opening the luggage compartment. A CODE CARD is supplied with the keys. This card shows the following: - the electronic code Important note - the mechanical code for the keys, to be given to your Authorized If the keys are lost or stolen, you can request a duplicate from Ferrari Dealer if you request duplicates of the keys. your Authorized Ferrari Dealer (see section “Duplicating the keys” on page 18). Warning The code numbers on the CODE CARD must always be kept in a safe and protected place, not accessible to others. Important note In the event of a change of ownership, it is essential that the new vehicle owner is provided with all the keys and with the CODE CARD. 16 General

Alarm system - When starting the engine, press the ENGINE START button on 1 the steering wheel: The FERRARI CODE system 1) If the code is recognized, the CODE warning light A on the instrument panel turns off when the check procedure has been The vehicle comes equipped with an electronic immobilizer system completed, whereas the OBD warning light B turns off when (Ferrari CODE) which is automatically activated when the ignition the engine is started once the ECU has completed its diagnostic key is removed. cycle. In these conditions, the protection system has recognized The keys are equipped with an electronic device which transmits the key code and deactivates the immobilizer. a coded signal to the Ferrari CODE ECU. Once this ECU has recognized the signal, the engine can be started. 2) If the CODE warning light A illuminates permanently, it means that the code has not been recognized. If this occurs, it is Operation advisable to turn the key back to position 0 and then back to II. Each time the ignition key is removed from the 0 position, the If the immobilizer device remains active, try with the other key. protection system activates the engine immobilizer. Important note If you still cannot restart the engine, contact your Authorized Ferrari Dealer. A B A General 17

- While driving, with the ignition key in position II: 1) If the CODE warning light A illuminates, it means that Important note the system is performing a self-diagnostic cycle. At the first Each key provided has its own specific code, which must be opportunity, you can stop and test the system: stop the engine stored in the memory of the system control unit. by turning the ignition key to position 0, then turn the key back to position II. The CODE warning light A will illuminate and should go off within one second. If the warning light stays on, Important note repeat the procedure described previously leaving the key at 0 for more than 30 seconds. Contact your Authorized Ferrari Dealer immediately to have all the keys stored in the system memory. Important note If the problem persists, please contact your Authorized Ferrari Duplicating the keys Dealer. If you request additional keys, provided that the conditions to satisfy your request are met, remember that the codes must be 2) If the CODE warning light A flashes, it means that the vehicle is stored (up to a maximum of 7 keys) on all the keys. not protected by the immobilizer. Contact your Authorized Ferrari Dealer directly and bring the following with you: - all the keys in your possession - the CODE CARD for the Ferrari CODE system - a personal identity document - the documents proving ownership of the vehicle The codes of the keys that are not available when the new A memorization procedure is performed will be deleted from the B memory, in order to prevent that any lost or stolen keys are used to start the vehicle. A 18 General

Replacing remote control batteries Warning If you press one of the three buttons of the key and this does not activate the corresponding function, check for correct operation of There is risk of explosion if the battery is replaced with an 1 the alarm system functions using the other remote control before incorrect type. replacing the batteries. Dispose of used batteries in the proper manner. Replace the remote control batteries as follows: - open the key cover C using a small screwdriver at the position Electronic alarm indicated by the arrow - remove the two batteries E by pushing in the direction indicated by The electronic alarm system performs the following functions: the arrow to release them from the retainer cover D - remote control for central door locking/unlocking - fit two new batteries of the same type, observing the indicated polarity - perimeter surveillance, detecting if doors and lids are opened - close the key cover C. - motion surveillance, detecting intrusion in the passenger compartment - vehicle movement surveillance. Important note Do not use sharp tools to remove the cover and be careful to Activation avoid damaging the remote control. To turn on the electronic alarm, press button F on the key: - the direction indicators flash once - the system “beeps” � � F C G General 19

- the red LED on the dashboard flashes Deactivation - the central door locking system is activated and the doors are To deactivate the alarm system press button G on the key: locked. - the direction indicators flash twice The system activates after approximately 25 seconds. - the system beeps twice When the electronic alarm is activated, the user may request - the red LED on the dashboard turns off opening of the luggage compartment; in this case, the motion and anti-lift sensors are temporarily deactivated. - the dome lights and the lights under the doors illuminate If the luggage compartment is then closed, the sensors will be - the central door locking system is deactivated and the doors are reactivated. unlocked. If the direction indicators and the red LED on the dashboard flash Pressing button G twice unlocks the doors and also turns on the 9 times when you activate the alarm system, it means that one of low beams for 30 seconds. the doors or the front/rear lid is not properly closed and therefore The alarm system is off and it is therefore possible to get into the is not protected by the perimeter surveillance. Check for correct vehicle and start the engine. closing of the doors, front/rear lid and close any open door or lid without deactivating the alarm system. The direction indicators flashing once indicate that now the door or the front/rear lid is closed properly and is protected by the perimeter surveillance. Warning If the direction indicators and the red LED on the dashboard flash 9 times when the alarm system is activated with doors, rear F and front lids properly closed, it means that the self-diagnostic feature has detected a malfunction in the system. Contact your Authorized Ferrari Dealer to have the system checked. G 20 General

Deactivating the anti-lift alarm Important note If the remote control battery is dead, to enter the vehicle, insert Press button H to deactivate the anti-lift alarm system. When this function is deactivated, the LED on the button will flash for about 3 seconds and will then turn off. 1 the key into one of the two door locks, the turn it to release the lock. The alarm siren will start to sound. Alarm memory Start the vehicle following the standard procedures. The alarm If the CODE symbol (see page 128) illuminates on the left TFT siren will deactivate. display for 10 seconds when the vehicle is started after system diagnosis, together with the message “Break-in attempted”, this means that an intrusion has been attempted. The alarm system memory is reset by turning the ignition key. H General 21

Identification plates and labels D E F C G B H A I J K L M N O P 22 General

1 Ref. Label/plate Position A Child seat warning Dashboard B Airbag maintenance Passenger side sun visor C Driver and passenger airbag warning (2) Driver side and passenger side sun visor D Radiator with anti-freeze RH engine compartment esthetic shield E Engine type and number Crankcase F Assembly number Engine compartment G Emission control data LH engine compartment esthetic shield H Engine/gearbox oil type LH engine compartment esthetic shield I Gearbox type and number Gearbox housing J V.I.N. label Rear driver-side door jamb K Conformity label Rear driver-side door jamb L Mercury content warning Rear driver-side door jamb M Tire pressure and type Driver-side door N TPMS warning Driver-side door O V.I.N. Windshield P Original paintwork Luggage compartment lid General 23

A Child seat warning C Driver and passenger airbag warning B Airbag maintenance D Radiator with anti-freeze 24 General

E Engine type and number G Emission control data 1 F Assembly number H Engine/gearbox oil type General 25

I Gearbox type and number K Conformity label J V.I.N. label L Mercury content warning 26 General

M Tire pressure and type O V.I.N. 1 N TPMS warning P Original paintwork General 27

Dimensions and weights Wheelbase 104.33 in. (2650 mm) Max. length 178.23 in. (4527 mm) Max. width 76.26 in. (1937 mm) Max. height 47.76 in. (1213 mm) Front track 65.83 in. (1672 mm) Rear track 63.23 in. (1606 mm) Front overhang 43.58 in. (1107 mm) 65.83 63.23 Rear overhang 30.31 in. (770 mm) Curb weight 3384 lbs (1535 kg)* 76.26 * With the vehicle fitted with the most popular options available 47.76 104.33 178.23 28 General

Main engine specifications Transmission ratios Engine Family BFEXV04.3GDI Gearbox ratios Differential/bevel gear pair ratio 1 Type F 136 FB Number of cylinders 8 1 = 3.077 Cylinder sequence V 90° 2 = 2.185 Cylinder bore 3.7 in. (94 mm) 3 = 1.626 5.143 Piston stroke 3.2 in. (81 mm) 4 = 1.286 Total displacement 4499 cm3 5 = 1.028 Compression ratio 12.5:1 6 = 0.839 Maximum RPM 9200 RPM 7 = 0.693 (with limiting device) R = 2.791 Max. power 416 kW (558 HP) Performance Corresponding RPM 9000 RPM 0 - 100 km/h 0 - 400 m Max. speed Max. torque 398.23 ft. lb. (62 mph) (1,312 ft.) (540 Nm) < 3.4 s 11.3 s > 202 mph (> 325 km/h) Corresponding RPM 6000 RPM Electric system Supply voltage Alternator 12 V Nippondenso 165 A SC3 Battery Starter motor Fiamm 12V - 70 A/h Bosch L3 VRLA 760A EN General 29

Fuel Consumption (miles per US Gallon) Shift Indicator Light (SIL) operating mode When the gearbox is used in “manual” mode (see page 153), City 12 the graphic symbol A appears just before reaching the speed Highway 18 recommended for operating the UP lever. After shifting gears or after exceeding the indicated speed, the Average fuel consumption 14 indicator turns off even if no gearshift is performed. These estimates are based on tests performed on vehicles equipped with the most popular optional equipment. The fuel economy values are calculated pursuant to the new EPA fuel economy labeling procedure for 2008 and later model years. You can also obtain other information from http://www.fueleconomy.gov. Reminder: Your actual fuel consumption may vary depending on your driving style and habits, vehicle maintenance, optional equipment installed, road and weather conditions. For best fuel economy, shift gears at the following speeds: 1st - 2nd 12,5 mph (20,12 km/h) 2nd - 3rd 17,5 mph (28,16 km/h) 3rd - 4th 22,5 mph (36,21 km/h) A 4th - 5th 27,5 mph (44,26 km/h) 5th - 6th 32,5 mph (52,30 km/h) 6th - 7th 37,5 mph (60,35 km/h) 30 General

Wheel rims and tires Wheel rims Important note 1 Front Rear Spare wheel Always check your tires regularly for wear 8.5” J x 20” 10.5” J x 20” 4.5” J x 20” and damage. Ferrari-approved tires Inflation pressure (cold) Front Rear Front Rear Michelin Pilot Sport 235/35 ZR20 295/35 ZR20 30.46 psi (2.10 bar) 29 psi (2.00 bar) Bridgestone Potenza 235/35 ZR20 295/35 ZR20 33.36 psi (2.30 bar) 33.36 psi (2.30 bar) Pirelli P Zero 235/35 ZR20 295/35 ZR20 30.46 psi (2.10 bar) 29 psi (2.00 bar) Optional tires Inflation pressure (cold) Front Rear Front Rear Bridgestone Potenza Run Flat 235/35 ZR20 295/35 ZR20 33.36 psi (2.30 bar) 36.26 psi (2.50 bar) Spare tire Inflation pressure (cold) Vredestein spare tire 146/60 ZR20 60.92 psi (4.20 bar) Winter tires Inflation pressure (cold) Front Rear Front Rear Pirelli Winter Sottozero 235/35 ZR20 285/35 ZR20 30.46 psi (2.10 bar) 29 psi (2.00 bar) General 31

Wheel Replacement Treadwear The treadwear grade is a comparative rating based on the wear rate Important note of the tire when tested under controlled conditions on a prescribed government test course. We recommend you read the entire procedure carefully before For example, a tire graded 150 would wear one and one-half (1- performing it. For more informations see page 210. 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual Wheel bolt 25.8 - 29.5 ft. lb. conditions of their use, and may differ significantly from the norm pre-tightening (35-40 Nm) due to variations in driving habits, service practices and differences Wheel bolt 73.8 ft. lb. in road characteristics and climate. Check your tires regularly for final tightening wear. (100 Nm) Traction The traction grades, from highest to lowest, are “AA”, “A”, “B”, and Uniform tire quality grading “C”. All passenger car tires must conform to Federal Safety requirements These grades represent the tire’s ability to stop on wet pavement in addition to these grades. under controlled conditions on specified government test surfaces of asphalt and concrete. Tires marked “C” have poor traction performance. DOT quality grades Tires type Pirelli P Zero Warning Tread wear 220 (front) The traction grade assigned to this tire is based on straight-ahead 160 (rear) braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Traction AA Temperature A 32 General

Temperature Warning The temperature grades are “A” (the highest), “B”, and “C”. Temperature grades represent the tire’s resistance to the generation Observing the recommended wheel alignment values is essential 1 of heat and its ability to dissipate heat under controlled indoor in order to obtain the best performance and the longest life of test wheel conditions. Sustained high temperature can cause the these tires. tire to deteriorate and can reduce tire life. In addition, excessive temperature can lead to sudden tire failure. Grade “C” corresponds to a level of performance which all tires installed on passenger Warning vehicles must meet under the Federal Motor Vehicle Safety If you are going to use standard tires on a vehicle that was Standard No. 109. Grades “B” and “A” represent higher levels originally equipped with “Run Flat” tires, you must contact of performance on the laboratory test wheel than the minimum your Authorized Ferrari Dealer to have the dashboard required by law. reprogrammed to prevent warning messages from being displayed on the left TFT display. Warning The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Run Flat tires (optional) The vehicle may come equipped with “Run flat” optional tires. This type of tire has a reinforced side A which allows the vehicle to continue traveling at moderate speed (50 mph - 80 km/h), even after a puncture, for a specific distance. When the instrument panel receives the “tire puncture” information from the tire pressure monitoring ECU, it calculates the residual tire life, and displays a warning in the dedicated area of the left TFT display after 31 miles (50 km). After 62 miles (100 km), a message warning the driver to stop the vehicle will be displayed (for further information, see the “Tire � pressure and temperature monitoring system” paragraph on page 88). General 33

Recommended Lubricants and Fluids Parts to be refilled Quantity Fill with: Ref. Page Engine Total system capacity 10.57 qts. PENNZOIL ULTRA™ SAE 5W-40 232 (10 l) Oil level between Min. and Max. 2.11 qts. (2 l) Oil consumption 1.06-2.11 qts./600 miles (depending on driving conditions) (1.0 - 2.0 l/1,000 km) Gearbox and differential 4.12 qts. SHELL TRANSAXLE 75W-90 GL5 233 (3.9 l) Clutch system and hydraulic controls 8.45 qts. SHELL DCT-F3 (8 l) Braking system 1.58 qts. SHELL DONAX UB BRAKE FLUID 235 (1.5 l) DOT4 Ultra Cooling system 17.44 qts. GLYCOSHELL LONGLIFE at 50% 234 (16.5 l) Hydraulic power steering system 1.69 qts. SHELL DONAX TX 234 (1.6 l) Fuel tank 22.72 US Gallon (86 l) Unleaded fuel 95 RON. 103 Reserve 3.69 US Gallon (14 l) Air conditioning and heating system Compressor 10.07 cu.in. (165 cc) PAG ISO 46 Refrigerant 1.38 ± 0.07 lbs. DELPHI RL 488 “R 134 A” (630 ± 30 g) Windshield washer/headlight washer fluid tank 1.32 US Gallon (5 l) Windshield washer fluid 236 34 General

Opening doors ...................................................... 38 Controls overview .................................................. 39 Seat adjustment .................................................... 41 Steering wheel adjustment ..................................... 42 Rear and side view mirrors ..................................... 43 Seat belts .............................................................. 44 Ignition switch ....................................................... 45 External lights and turn indicators .......................... 46 Starting and driving the vehicle ............................... 48

2 QUICK REFERENCE GUIDE

Opening Locking and opening the doors from the inside Doors Warning When a door is opened or closed, the window automatically moves down by approximately 0.8 in./2 cm (to its “target position”) to Always check that the doors have been closed properly to avoid damaging the upper weather strip. prevent them from opening while driving. When the door is closed, the window automatically moves up until it reaches the “upper limit”. Both doors can be locked by activating/deactivating the “LOCK/ UNLOCK” B button on the roof console. To lock the doors, press button B; when the door lock is activated, the light on button B Opening from the outside comes on. To deactivate the door lock, press button B until the Using the remote control, deactivate the alarm and the central door light goes out. locking system, or turn the key in the lock to deactivate the central If you pull handle C to open the door, the window will move down door locking system. to its target position. When the door is closed, it will move up until To open the door, pull handle A: the window will move down to its it meets its upper limit. target position. When the door is closed, the window will move up When the opening handle is operated, both doors are unlocked. until it meets the upper limit. B � C 38 Quick reference guide

Overview of controls 1 1 1 2 3 2 6 5 4 PS Ref. Control Page Ref. Control Page 1 Adjustable air vents 187 4 Light switch 146 2 Glove compartment 188 5 Side view mirror adjustment control 183 3 Right TFT display controls (NIT) 136 6 Left TFT display controls 108 Quick reference guide 39

Ref. Control Page Ref. Control Page 7 Left TFT display 108 16 Glove compartment opening button 188 8 Tachometer and gear display 133-134 17 Power window switches 104 9 Right TFT display 136 18 Performance Start button 173 10 Direction indicators 148 19 “R” reverse button 155 11 Windshield washer/wiper lever 143 20 Air conditioning and heating system controls 184 12 “Manettino” control 140-164 21 “AUTO” button 158 13 “ENGINE START” button 140 22 Hazard warning lights button 149 14 Suspension damping button 142-168 15 High beam and flashing lever 146 7 8 9 17 18 19 10 20 10 16 15 11 14 12 22 21 13 40 Quick reference guide

Adjustments Backward/forward adjustment Pull lever B up and slide the seat forward or backward to the Seats desired position. Release the lever and slightly move in the seat to check that it is locked in place. Warning As with all adjustments, seat adjustments must be performed when the vehicle is stationary. Warning The backward/forward adjustment must consider the fact 2 that airbag devices are placed in front of the driver and the Correct adjustment is very important for enhanced driving comfort passenger (see page 71). and maximum efficiency of the passive safety systems. Correct adjustment ensures there is adequate space between the Basic seat airbag and the driver/passenger (see page 71). The seat position can be adjusted using the special controls. Seat back rake adjustment Turn knob C clockwise or counterclockwise until it reaches the desired position. B C Quick reference guide 41

Tilting the backrest Steering wheel To tilt the seat, pull lever L up and push the backrest towards the The steering wheel can be electrically adjusted for rake and reach. front of the vehicle. It can only be adjusted if the ignition key is in position II. When the backrest goes back into position, it will automatically lock Move control A (on the left of the steering column) in the four once it has reached the correct position. directions to adjust the steering wheel. For further information on basic seat adjustment, refer to pages The position of the steering wheel is memorized together with the 176-177. position of the side view mirrors when the driver’s seat position is memorized (only in vehicles with Full Electric option, see page Electrically-adjustable seat (optional) 179). For further information on adjustment of the optional electrically- adjustable seat, refer to pages 178-179-180. Warning Racing seat (optional) Do not adjust the steering wheel while driving. For further information on adjustment of the optional Racing seat, refer to page 181. L A 42 Quick reference guide

Rear and side view mirrors 2) Mirror positioning: move control C in the four directions (up – down – right – left) to adjust the selected mirror. Internal rear view mirror 3) Mirror closure (optional): turn control C to the lower central Hold the internal rear view mirror and move it to the required lock position to close the side view mirrors. position. Once adjusted, rotate the control C into the upper central position On request, the internal rear view mirror can be fitted with an optional electrochromic mirror that automatically darkens to reduce where it will be locked in order to avoid changing the external mirror setting inadvertently. 2 the glare effect of the reflected light on the driver. The speed with The mirrors are designed to fold in both directions in the event of which the mirror darkens depends on the intensity of the light. a collision: if necessary, the mirrors can be pushed both backwards By pressing button B you can activate/deactivate the electrochromic and forwards. mode. When the electrochromic mode is activated, the green LED D comes on. Warning Side view mirrors The side view mirrors must always be positioned correctly while These mirrors can be electrically adjusted using the control C (with driving. the ignition key in position II) and are equipped with defogging Do not adjust the rear and side view mirrors when the vehicle is elements. moving. 1) Mirror selection: turn control C to the left or right lock position to select the mirror that requires adjusting. D C C B Quick reference guide 43

Seat belts If the driver’s seat belt is not fastened, when you turn the ignition key to position II, the warning light on the instrument panel illuminates and remains on as long as the seat belt is not fastened. Warning 55 seconds after a speed of 6 mph (10 km/h) is exceeded, a buzzer The seat belts must be properly adjusted and fastened at all sounds warning the driver that the seat belt is not fastened. times. When a speed of 12 mph (20 km/h) is exceeded, the buzzer Correct use of the seat belts can reduce the risk of serious injury activates immediately and stops after 90 seconds. in the event of an accident or if the vehicle overturns. This acoustic signal is emitted only once, even if the vehicle speed goes above and below the above mentioned limits. It is repeated Fastening the seat belts (when the vehicle speed is in the indicated ranges) only if the seat belt is fastened and unfastened again or, in any case, every time the After positioning the seat correctly: engine is turned off and then on. • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it Unfastening the seat belts out, let it wind back a little and pull it out again without jerking it). • Push the release button E. • Make sure that it has clicked into the locked position: hold the • Guide the latch plate A back to its rest position. belt and pull it to check that the latch plate has been inserted correctly. Warning • Position the seat belt correctly. Do not allow children to be held on a passenger’s lap using only one seat belt for both of them. For further information, refer to the “Safety” chapter on page 58. � A � E 44 Quick reference guide

Ignition switch Warning The ignition key can be turned to 2 positions: Position 0 - Stop Never remove the key when the vehicle is moving! Engine off, key removable. The steering wheel will lock with the first rotation of the steering wheel. When the key is even only partially extracted, the steering column is locked. Always remember to remove the key from the ignition when you get out of the vehicle! 2 The hazard warning lights and parking lights can be activated. Never leave children unattended in the vehicle. To facilitate steering wheel release, turn the steering wheel slightly clockwise or counterclockwise while turning the ignition key. Position II - Start When the key is turned to this position (key-on) the signals generated by the vehicle systems are checked. The left and right TFT displays are activated on the instrument panel and when the signals have been checked, the gear display comes on (see page 134). For further information, see page 101. II 0 Quick reference guide 45

External lights and turn indicators High beams To turn on the high beams when the light switch A is set to , Light switch pull back lever B on the steering wheel. The switch A, on the dashboard to the left of the steering wheel, When the high beams are on, the appropriate indicator light can be set to five different positions: illuminates on the instrument panel. 0 Lights off Then push lever B towards the dashboard or pull it back to turn off the high beams and turn on the low beams. Running and license plate lights on (*) Low beams on (*) Important note Parking lights Follow the road regulations of the state or province you are AUT Automatic operation of the external lights according to traveling in for using the high beams. ambient light. (*) The appropriate indicator light on the instrument panel illuminates. Flashing the headlights The headlights can be flashed by pushing the left-hand lever B towards the dashboard. B A 46 Quick reference guide

Direction indicators Rear fog lights Quickly press the left indicator or right indicator button C on the The rear fog lights are turned on only if the high beams or low steering wheel to turn on the relevant turn indicator. beams are on when button D is pressed. The appropriate indicator light or will illuminate on the instrument panel. Important note The turn indicator goes off when the steering wheel is realigned. Holding down one of the two C buttons (for more than Use the rear fog lights only in poor visibility conditions. 2 0.3 seconds) temporarily turns on the relevant turn indicator: it is Hazard warning lights turned off after 3 flashes (“lane change” function). Press button E to turn on the hazard warning lights. All the turn indicators will start blinking intermittently; these lights will operate with the ignition key in any position. When the lights are on, the appropriate indicator lights on the instrument panel and on the button flash. To turn them off, press the button again. For further information, refer to the “Lighting system” paragraph on page 146. PS C C D E Quick reference guide 47

Starting and driving the vehicle System start-up Important note After turning the ignition key to position II (key-on), the left and The vehicle is equipped with an electro-hydraulically controlled right TFT displays are activated on the instrument panel and system gearbox system operated by means of paddles behind the diagnosis is performed. During diagnosis, which lasts approximately steering wheel. 5 seconds, a check is performed on the warning lights on the panel The default setting for the DCT gearbox is always “Auto easy and the presence of any faults is checked. exit” mode (see page 158). Once the system check has been completed, the gear display is Every time the vehicle is started, the DCT gearbox is in “Auto activated and the letter “P” (Parking) or “N” (Neutral) will be easy exit” mode (see page 158) unless the vehicle was in “Auto” displayed. mode when the engine was turned off. To exit the “Auto easy exit” mode operate the UP and DOWN Important note paddles (while the vehicle is moving) or press the AUTO button on the center console. BEFORE YOU DRIVE If the warning light A does not turn off after diagnosis, indicating a fault in the gearbox also shown by the symbol and special message on the left TFT display (see page 133), contact your Authorized Ferrari Dealer. A A 48 Quick reference guide

Starting the engine Important note Before starting the engine, make sure that the alarm system and all Immediately release the UP and DOWN paddles or button R electrical devices with high power absorption are turned off. after the gearbox display shows that the gear has been engaged; • Make sure that the electric parking brake is applied and that the a prolonged maneuver would cause the gearbox failure warning doors are closed. light to illuminate (see page 133) and activating the buzzer. • Hold the brake pedal down when starting the engine. 2 Important note Warning None of the gears can be engaged if the luggage compartment Do not press the accelerator pedal. lid is open or not properly closed. When the vehicle is stationary, with the driver-side door open or not properly closed and the • Turn the ignition key to position II and wait for the gearbox brake pedal released, the system disengages the gear engaged display to come on. after approximately two seconds. • Press the ENGINE START button (see page 140) and release it as soon as the engine starts. Do not hold the ENGINE START button down for a long time. If the engine does not start, turn the key back to position 0 and wait for the gear display to go off before retrying. Warning DOWN UP Hold the brake pedal down while starting the engine. Quick reference guide 49

If the engine fails to start after several attempts, check for one of the following causes: Warning • insufficient speed of the starter motor (dead battery) If the “UP” and “DOWN” paddles are not working, the message • faulty ignition device “Depress brake pedal and press PS to engage gear” will appear • faulty electrical contacts on the left TFT display; you can therefore engage the gear by pressing the PS button on the center console (see page 173) and • fuel pump fuses blown. the brake pedal. Warming up the engine In these cases, the “Performance Start” function is not available. If the engaged gear was R, the PS button must be pressed twice Do not run the engine at high speed until the engine oil temperature to engage 1st gear. has reached at least 65-70 °C (149-158 °F). Starting the vehicle Important note With the engine started, the vehicle stationary and the brake pedal pressed, pull the right-hand “UP” paddle towards the steering When reverse is selected, an acoustic safety signal beeps wheel to engage 1st gear. intermittently as long as “R” is engaged. Release the brake pedal and press the accelerator to start off. With the engine running and the vehicle stationary, you can change If the system automatically selects 2nd gear when attempting to directly from 1st or 2nd gear to R (reverse) by pressing R and from shift from R to 1st gear, this indicates that 1st gear has jammed. reverse to 1st by moving the UP paddle. Therefore, this is not a malfunction, as it falls within the system operating logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has jammed. During prolonged stops with the engine running, it is advisable to keep the gearbox in “N”. R Important note If you allow the vehicle to move forward in N, when UP or DOWN is requested, a gear will be engaged that corresponds to the speed of the vehicle. 50 Quick reference guide

UP-shifting Stopping the vehicle Use the right-hand UP paddle without releasing the accelerator When the vehicle stops, the system automatically engages 1st gear pedal. unless Neutral has already been requested. An UP-shift request is not accepted when engagement of the When the vehicle is stationary and the engine is running, hold the requested gear forces the engine to underrev or if an UP-shift is brake pedal down until ready to move again. already in progress due to engine overrevving. For further information, see page 156. Turning off the engine 2 The engine can be turned off with the gearbox either in “N” or DOWN-shifting with a gear engaged. Use the left-hand DOWN paddle without releasing the accelerator After turning the ignition key from position II to position 0, the pedal. gearbox display will remain on for a few more seconds to display A DOWN-shift request is not accepted if engagement of the the engaged gear. If the gearbox is in “N” a buzzer will sound. requested gear forces the engine beyond a certain RPM, depending Before turning off, the letter “P” is displayed on the gearbox display on the gear requested, or if a DOWN-shift is already in progress to inform the driver that the Park Lock has been activated. due to engine underrevving. For further information, see page 156. Warning “N” (Neutral) request Never leave the vehicle with the gearbox in “N”. Always make sure that the letter “P” (Parking) appears on the gear display. With the engine running, pull both UP and DOWN paddles towards the steering wheel at the same time without pressing the brake pedal to request neutral “N”. For further information, see page 172. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. Quick reference guide 51

Passive safety......................................................... 56 Active safety .......................................................... 57 Seat belts .............................................................. 58 How to fasten seat belts ........................................ 60 Pretensioners......................................................... 62 Child safety ........................................................... 64 Additional Occupant Protection Systems ................ 70 Driver and passenger airbags .................................. 71 Passenger airbag deactivation ................................ 76 Side airbags........................................................... 80 Fuel inertia switch.................................................. 83 ABS and EBD ........................................................ 84 Stability and Traction Control ................................ 85 Electric parking brake ............................................ 87 TPMS.................................................................... 88

3 SAFETY

Ferrari has designed and built a high performance vehicle. Emissions Please note that it is essential to comply with all state, local and provincial regulations. Warning • The exhaust gas generated by the running engine may be Special warnings hazardous, especially when in closed spaces. In addition to This vehicle has been designed to comply with homologation, consuming oxygen, the engine discharges carbon dioxide, Federal Motor Vehicle Safety Standards and environmental carbon monoxide and other toxic gases. regulations. • Fuel is highly flammable and emits vapors which may be The careful and cautious behavior of the driver is also of utmost noxious if inhaled. importance. Do not use open flames or create sparks near the open fuel Particular attention must be paid to: tank or in any other condition where fuel comes into contact • Overheated components. High temperatures develop in the with air. engine compartment near the exhaust system. Do not park the vehicle on, over or near paper, grass, dry leaves or other Lubricants flammable materials. They could catch fire if they come into contact with hot parts of the exhaust system. Do not fit other heat Warning shields or remove those fitted on the exhaust system. Do not let flammable substances come into contact with the exhaust system. • The oils used may also be flammable: take the same • Moving parts of the vehicle such as belts, fans, etc. must always be precautions as those adopted for fuel. adequately protected. Do not remove the guards or operate on the moving parts without taking necessary precautions. Flammable fluids • Installations under pressure such as braking system, air conditioning system, cooling system and lubrication system may Warning create pressures inside them. Do not perform any operation which may cause gas or liquids to escape with the risk of injury to • The fluid in the battery is poisonous and corrosive. Do not let persons and damage to property. it spill and come into contact with the skin, eyes or objects. Do not use open flames or create sparks near the battery. Fuel inertia switch • See page 83. 54 Safety

Warning Warning Engine exhaust, some of its constituents, and certain vehicle To help ensure an effective restraining action, the seat belt components contain or emit chemicals known to the State of must be fastened correctly with the seat backrest in the upright California to cause cancer and birth defects and reproductive harm. position. In addition, certain fluids contained in vehicles and certain products The seat belt is fastened correctly when the upper part of the of component wear contain or emit chemicals known to the State of belt crosses the center of the shoulder (not the neck) and the California to cause cancer and birth defects or other reproductive abdominal section is fitted over the hips (not the abdomen). harm. Make sure that the belt is not twisted and that it passes closely over your body; if not, in the event of a head-on collision, it may move and cause injury to the abdomen. 3 Warning Avoid wearing bulky clothing that may interfere with the proper Seat belts must be worn at all times and must be properly operation of the seat belts. fastened and adjusted! Correct use of the seat belts can significantly reduce the risk and severity of injury if an accident occurs. Warning Each seat belt has been designed to help protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. Do not place babies, small children or other persons on your lap. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Safety 55

Passive safety - occupant protection system ECU The passive safety system has been designed to help reduce the risk - ECU auxiliary sensors and severity of injury if an accident occurs. - instrument panel warning light (see page 71) The vehicle is equipped with the following seat belts: - inertia switch - 3-point driver's seat belt with pretensioner and load limiting device (see page 58) Warning - 3-point passenger seat belt with pretensioner and load limiting device (see page 58). The protective action of the airbags is always integrated with the seat belts and the pretensioners. The compulsory use of the seat belt is mandated by relevant state and provincial regulations. Warning Additional safety systems are not a substitute for seat belts. All Deformable body occupants must always wear a seat belt. Correct use of the seat The deformable body is designed to absorb shock and distribute belts combined with use of the additional safety systems help it over the entire structure of the vehicle allowing progressive provide optimal protection to the occupants in various types of deceleration. collisions. The passenger compartment structure, on the other hand, has been designed to provide maximum resistance without undergoing The vehicle also has the following additional occupant protection deformation in order to help provide a protective safety cage for system components (see also page 70 “Additional Occupant the occupants. Protection Systems”): - front driver's airbag (for operating functions see page 71) - front passenger airbag (for operating functions see page 71) - driver's head protection side airbag (side airbag) (for operating functions see page 80) - passenger head protection side airbag (side airbag) (for operating functions see page 80) - seats (see page 176) - deformable body 56 Safety

Active safety The aim of the active safety system is to help reduce the risk of accidents and injury severity. The vehicle has been designed to provide a high level of safety for the occupants. The following systems are specific active safety components: • braking system • air conditioning and heating system • external lights • buzzer and warning lights (flashing) 3 The braking system includes the mechanical brake system and the electronic stability and traction control system (ABS and EBD): this is designed to help prevent the wheels from locking and to help provide good handling and stability. The air conditioning and heating system in the passenger compartment can add to driving comfort and keep you alert so that you can react quickly when necessary. It is very important to be able to see the road clearly and be seen. External lights must be turned on when the conditions so require. Safety 57

Seat belts Statistics show that when used correctly, seat belts help reduce Warning the risk of injury in various types of crashes including the risk of For an effective restraining action, the seat belt must be fastened ejection from the vehicle and occupants' impact with the interior of correctly with the seat backrest in the upright position. the vehicle. The seat belt is fastened correctly when the upper part of the If not fastened, the seat belts do not provide any type of protection. belt crosses the center of the shoulder (not the neck) and the Before every trip, always make sure that all occupants are wearing abdominal section is fitted over the hips (not the abdomen). their seat belts. Make sure it is not twisted and that it passes closely over your body; if not, in the event of a collision, it may move and cause Warning injury to the abdomen. Seat belts must be worn at all times and must be properly Avoid wearing bulky clothing that may interfere with the proper fastened and adjusted! operation of the seat belts. Correct use of the seat belts can help reduce the risk of serious injury in the event of an accident. The seat belts have a lap-shoulder belt with an automatic emergency-locking retractor and are fitted with a pyrotechnic- powered pretensioner and an automatic system that is designed to help reduce the force applied to the occupant. 58 Safety

Warning Warning Do not let the seat belts come into contact with sharp objects. Periodically check the condition of the seat belts. If the belt They may be damaged and may consequently tear in the event shows signs of wear, it must be checked by a qualified person of a collision. and replaced if necessary. Contact your Authorized Ferrari Dealer immediately. Warning Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. 3 The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not place babies, small children or other persons on your lap. If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Warning Do not attach or pin anything onto the seat belts: they may be damaged and may consequently break in the event of a collision. Warning If a seat belt has come into contact with sharp objects or was somehow perforated or torn, we recommend that you have it immediately replaced by yout Authorized Ferrari Dealer. Safety 59

How to fasten seat belts • Make sure that it has clicked into the locked position: hold the belt and pull it to check that the latch plate has been inserted correctly. Warning • Position the seat belt correctly. For an effective restraining action, the seat belt must be fastened If the driver’s seat belt is not fastened, when you turn the ignition correctly with the seat backrest in the upright position. key to position II, the warning light D on the instrument panel The seat belt is fastened correctly when the upper part of the lights up and remains lit until the seat belt is fastened. belt crosses the center of the shoulder (not the neck) and the 55 seconds after a speed of 6 mph (10 km/h) is exceeded, a buzzer abdominal section is fitted over the hips (not the abdomen). sounds warning the driver that the seat belt is not fastened. Make sure it is not twisted and that it passes closely over your When a speed of 12 mph (20 km/h) is exceeded, the buzzer body; if not, in the event of a collision, it may move and cause activates immediately and stops after 90 seconds. injury to the abdomen. This acoustic signal is emitted only once, even if the vehicle speed Avoid wearing bulky clothing that may interfere with the proper goes above and below the above mentioned limits. It is repeated operation of the seat belts. (when the vehicle speed is in the indicated ranges) only if the seat belt is fastened and unfastened again or, in any case, every time the Once you have adjusted the seat correctly (see page 176): engine is turned off and then on. • Grip the latch plate A, slowly pull the belt and insert the latch plate into the buckle B (if the belt locks while you are pulling it out, let it wind back a little and pull it out again without jerking it). � A D � 60 Safety

Warning Each seat belt has been designed to protect only one occupant. If more than one person uses the same seat belt, the risk of injury in the event of an accident is increased. The seat belt must never be passed around a baby, child or other person sitting on a passenger's lap. Do not place babies, small children or other persons on your lap. 3 If there is a collision, the weight of an adult may cause the child to be crushed by the seat belt causing severe or even fatal injuries. Unfastening the seat belts • Push the release button E. • Guide the latch plate A back to its rest position. A E Safety 61

Pretensioners When a pretensioner is activated, a small amount of smoke is released. This smoke is not harmful and does not indicate the The seat belts are fitted with pyrotechnic-powered pretensioners. presence of fire. The pretensioner is designed to be activated by the airbag ECU in the event of certain head-on collision of sufficient severity, or in a side collision of sufficient severity. The belt will rewind a small Warning amount just before the restraining action begins, thereby improving Activation of the pretensioners only depends on the status of the the fitting across the occupant's body. seat belts and is not affected by the occupant's presence. Always Activation of a pretensioner is indicated by the illumination of the wear your seat belt! warning light A on the instrument panel. If the seat belt is not fastened, the pretensioner will not activate, even if the seat is occupied. Warning Pretensioners that have been activated will no longer function The seat belts are fitted with a load limiting device. The load and may not be repaired under any circumstances. Contact your limiting device is located in the belt retractor and allows controlled Authorized Ferrari Dealer for replacement. release of the belt during a collision thereby limiting the impact that the belt has on the occupant's body. Maintenance of seat belts and pretensioners • Following a serious collision, replace the seat belts that were worn at the time even if they do not appear to be damaged. • Periodically check that the anchor points are tight and that the A seat belt is in perfect condition and slides smoothly. • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. • To clean the seat belt, wash it by hand with mild soap and water and let it dry. Do not use strong detergents, bleach or aggressive solvents, as they can weaken the fibers. Make sure the retractors do not get wet: proper functioning is only ensured if they are kept dry. • If immersed in water or mud, pretensioners must be replaced. 62 Safety

• The pretensioners require no maintenance or lubrication. • Pretensioners must be replaced at regular intervals as indicated in the “Warranty Book”. Important note All work on any part of this safety system must be performed by your Authorized Ferrari Dealer. Warning Removing or making modifications of any kind to the seat belts, 3 belt retractors and pretensioners is not allowed. Maintenance work involving strong impacts, vibrations or heating of the pretensioner area may activate them; vibrations caused by road bumps will not have this effect. Safety 63

Child safety Warning Warning Drive slowly and pay maximum care and attention when transporting children. Sudden acceleration caused by sports- Established legislation in some countries already provides style driving may be dangerous for children even if no collision that children under 12 years of age may not travel in the front occurs. passenger seat. Because of their size, children are at greater risk than adults. Suitable restraint or safety systems must be used. Warning All minors whose physical characteristics (i.e., age, height, Do not transport children in rearward facing child restraint weight) fall within the legal limits in force in each country/ systems on the front passenger seat. state/province must be protected by approved restraint or safety Although the front passenger airbag has been designed and systems (e.g., child seats). developed not to cause injury, it should be stressed that the You are advised to always use approved child restraint systems muscle and bone structure of children is not fully developed bearing the proper markings. and therefore vulnerable; the risk of very severe or even fatal injury caused by activation of the airbag cannot therefore be excluded. Warning Never leave children ALONE and/or unattended in the vehicle Warning since this may constitute a danger to them and others. If you absolutely must carry a child on the front passenger seat in a rearward facing child restraint system (e.g., in an emergency Warning situation), the front passenger seat must be positioned as far back as possible with the sides of the seat as far open as possible This is an extreme sports vehicle. Do not use the vehicle to and the lumbar support adjustment as low as possible. The seat transport infants, since sudden acceleration may cause injury. must also be adjusted to the lowest position to enable the child restraint system to be correctly installed. 64 Safety

Warning Warning Be sure that seat back of the child restraint system contacts the For installation and use (how to secure the child to the restraint seat back of vehicle passenger seat. If there is an interference system) of child restraint systems, follow the instructions that between the child restraint and the headrest, DO NOT install the manufacturer of the device provides. child seat, and select another model child seat. Warning Because of their size, children are at greater risk than adults. Suitable restraint or safety systems must be used. Carefully follow the instructions provided with the child seat: All minors whose physical characteristics (i.e., height, weight) fall within the legal limits in force in each country must be protected keep them in the vehicle together with the documents and this manual. Do not use second-hand child seats or child seats with 3 by approved restraint or safety systems (e.g., child seats, cushions). no instructions. You are therefore advised to ALWAYS use certified child restraint systems that bear the proper approval marking and check they Warning comply with Federal Motor Vehicle Safety Standard 213. Follow the instructions given by the child restraint system Warning manufacturer when choosing, installing and using the restraint system, since failure to do so may compromise its protective Incorrect fastening of a child restraint system increases the risk action. of injury to the child if an accident occurs. - The seat belts in the vehicle have been designed and tested to Warning protect persons weighing at least 79 lb (36 kg) and taller than 59 Always check the seat belts have been securely fastened by in. (1.50 m). pulling on the seat belt. - To properly protect children outside these limits, specific restraint systems with dedicated belts or accessories capable of adapting the child’s position to the vehicle seat belts must be fitted. Safety 65

Warning Warning After an accident, have all the parts of the child restraint system If violent braking or a collision occurs, children who are not in and vehicle seat belt system checked and replace them if a restraint system can be thrown against the dashboard or the necessary. windshield: this may lead to serious or even fatal injury to the Any work must be performed by an Authorized Ferrari Dealer. child. Warning Warning Children must never travel seated on a passenger’s lap. A child In the event of an accident, an improperly fastened child weighs very little until a collision occurs! In a collision, a child restraining system can increase the risk of injury. becomes so heavy that it would be impossible to hold onto him/ her. For example, in the event of a collision at only 25 mph (40 km/h), a child weighing 12 lb. (5.5 kg) exerts a force equal to 240 Warning lb. (110 kg) on the arms of the person carrying him/her. Children Never allow children to travel sitting in the lap of an adult. must always be protected by a suitable restraining system. If there is a collision, the adult's weight may crush the child against the seat belt or the dashboard: this may lead to serious Children must always be transported in restraint systems that are or even fatal injury to the child. suitable for their size. Before choosing a child restraint system, always check that: Important note - it is certified. Child seats certified according to Federal Motor Vehicle Safety Standard 213 NO modifications must be made to the seat belts and child - it is suitable for the height and weight of the child to be restraint systems: any modifications may seriously jeopardize the transported (CAREFULLY FOLLOW the instructions in the child safety of the child restraint system. restraint system use and maintenance manual) - it can be securely installed in the vehicle in compliance with the child restraint system manufacturer's instructions - the use and installation instructions are easy to understand. 66 Safety

Warning Warning If the front passenger airbag is not disabled by using BabySmart™ Each time the seat belt is used to fasten a normal occupant, child restraint system (see page 76), rearward-facing child seats the automatic seat belt winding locking system will have to be must not be used on the front passenger seat as the airbag could deactivated. cause serious injuries during deployment, even in minor collisions. Warning Warning Always remember to deactivate the seat belt locking mechanism An incorrectly installed child seat cannot protect the child as intended in the event of an accident, hard braking or sudden when removing the child seat. Having the retractor locked can be dangerous when the seat belt is used for directly restraining 3 change of direction and can lead to serious injuries to the child. a passenger. Warning Warning Never place objects such as pillows or cushions underneath the Protect the child restraint from intense sunlight by covering it child restraint. The entire base of the child restraint must always (e.g., with a light blanket or cloth). The plastic parts of the child be directly resting on the seat surface. seat can become hot when exposed to sunlight and can burn your child if he/she comes in contact with them. To transport a child, use the seat belts to secure the child restraint system to the vehicle seat and make sure you have activated the automatic seat belt winding locking system before installing the Warning child seat in the vehicle. In countries where it is already a legal requirement, children To activate the automatic seat belt winding locking system, pull the under 12 years of age may not travel in the front passenger seat. seat belt until the belt completely unwinds. At this point, the belt ALWAYS COMPLY with the legal requirements in force in your retractor will only allow the seat belt to rewind. own country. The fact that the seat belt cannot be pulled out confirms that the seat belt locking system has been activated. To deactivate the locking system, unfasten the seat belt in order to allow it to rewind completely. Safety 67

Child seat anchorage Standard seat The vehicle is equipped with a top tether anchor point A. The standard seat has a fixed headrest. If you are using a child seat with a single tether, route the tether over the headrest (see Picture Use of the top tether anchor point is designed to enhance the 1). Push and pull the child restraint in different directions to be restraining action of the child seat and is recommended. Please sure it is secure. check your child seat manual for instructions on how to install the child seat in the vehicle, and strictly follow these instructions. If you are using a child seat with a dual tether, route the tether around the headrest (see Picture 2). Push and pull the child The presence of the top tether fastening point does not preclude restraint in different directions to be sure it is secure. the use of the vehicle seat belts to secure the child seat. Warning Be sure that seat back of the child restraint system contacts the seat back of vehicle passenger seat. If there is an interference between the child restraint and the headrest, DO NOT install child seat, and select another model child seat. Figure 1 Figure 2 A 68 Safety

Racing seat (optional) If the vehicle is equipped with Racing seats (optional), and if you are using a child seat with a single or dual tether, the tether strap must be fed through the opening in the seat back of the passenger seat (see Picture 3 and Picture 4). 3 Figure 3 Figure 4 Safety 69

Additional Occupant Protection Systems The front driver's airbag and front passenger airbag have been designed to increase the level of protection given by the seat belts in the event of certain head-on collision of sufficient force (see Warning page 71). Additional Occupant Protection Systems are not a substitute for The driver's head protection side airbag and passenger head seat belts but increase their efficiency. Correct use of the seat protection side airbag have been designed to increase the level belts, with the supplementary action of the Additional Occupant of protection given by the seat belts in the event of certain side Protection Systems, helps provide increased protection in the collisions of sufficient force and are placed between the occupant’s event of a head-on collision or certain vehicle roll-overs. head and external structures which could penetrate the passenger compartment and cause injury (see page 80). Additional Occupant Protection System components The Additional Occupant Protection System components are: - Seat with built-in headrest. - Dual-stage front driver's airbag. - Dual-stage front passenger airbag. - Driver's head protection side airbag (side airbag). - Passenger head protection side airbag (side airbag). - Driver's seat belt (3-point with pretensioner and an automatic system designed to reduce the force applied to the occupant). - Passenger seat belt (3-point with pretensioner and an automatic system designed to reduce the force applied to the occupant). - Electronic Control Unit (ECU). - Additional sensors. - Instrument panel warning light. - Deformable body. 70 Safety

Warning Warning The warning light A illuminates when the ignition key is turned The front airbags have been designed not to inflate if a minor to position II. If no malfunctions are detected, it goes out after collision occurs, even if it is a head-on collision. The seat belts 4 seconds. If the warning light does not illuminate, if it remains have been designed to help reduce the risk of injury if a minor on or if it illuminates while driving, contact your Authorized collision occurs. Ferrari Dealer immediately. Driver and passenger airbags Warning Warning The driver and the passenger must maintain a distance of at least 10 in. (25 cm) from the steering wheel and the dashboard. 3 Always drive with your hands on the rim of the steering wheel The front airbags do not provide protection in the event of so that in the event of activation, the airbag can deploy without rear-end or side collisions, some head-on/angular collisions, obstruction. roll-overs or subsequent collisions (if there is a second collision once the airbags have been deployed in an earlier collision). The Driving with your hands on the steering wheel spokes or on the seat belts have been designed to help reduce the risk of injury airbag cover increases the risk of injury to your wrists and arms. in the event of certain roll-overs or in a subsequent collision. A 10 in. At least Safety 71

Warning Environment The front passenger must be seated correctly and must avoid When the system is activated, gases are released in the form putting hands, feet or legs on the dashboard since if the front of smoke, together with the gas used for inflating the airbags. airbag is activated, it may cause injury to legs and prevent the These gases are not harmful. airbag from working properly. The driver's airbag has been designed to be deployed according Operation to the following strategy: The front airbags are controlled by an ECU which is designed to • For low severity crashes, the airbag control unit will not deploy activate them in the event of certain head-on collisions of sufficient the airbag. severity. • For crashes of higher severity, the control unit will deploy the In the event of a collision with an impact force that causes driver airbag in low energy mode. deceleration that exceeds the value set for the internal sensor, the • For crashes of even higher severity, the control unit will deploy ECU is designed to transmit a signal to deploy the airbags. The the driver airbag in high energy mode. airbags will begin to inflate, breaking the cover along the breakage line and is designed to deploy completely in a few hundredths of The passenger airbag has been designed to be deployed seconds. Once deployed, they will serve as protection between the according to the following strategy: driver and/or passenger and structures that could cause injury. • For low severity crashes, the airbag control unit will not deploy The airbags are designed to deflate immediately afterwards. the airbag. • For crashes of higher severity, the control unit will deploy the Warning passenger airbag in low energy mode. • For crashes of even higher severity, the control unit will deploy The driver and passenger should not carry objects (drink cans the passenger airbag in high energy mode. or bottles, pipes, etc.) that may cause injury if the airbags are activated. Warning Persons, animals or items must not be placed between the airbags and the occupant. The driver and passenger should always fasten their seat belts and sit in an upright position, as far as possible away from the airbag. 72 Safety

Warning Important note Always keep the backrest of your seat in the upright position Do not cut or tamper with the connectors of the airbag harness and sit with your back properly resting against it. or on the airbag modules. Important note Warning Do not modify the system components or wiring, under any Do not cover the steering wheel and the padded panel on the circumstances. dashboard on the passenger’s side with adhesive tape or treat it With the ignition key inserted and in position II, although the in any way. 3 engine is off, the airbags can still be activated when the vehicle is stationary if it is hit by a moving vehicle. Warning Remember that if the ignition key is set to 0 none of the safety In the event that the airbags are deployed, these objects would devices (airbags or pretensioners) are activated in the event of a be projected into the passenger compartment at a high speed collision; failure of the airbags to inflate in these circumstances is that would seriously jeopardize the safety of the occupants. not indicative of a system malfunction. Do not place objects above or near the top of the dashboard and the steering wheel. Warning The airbag modules are subject to wear and tear and must be replaced at the intervals indicated in the “Warranty Book” EVEN if the vehicle has NOT been involved in a collision. Safety 73

Warning Important note Do not modify the airbag modules in any way (see figure on the The airbag system components have been specially designed previous page). Do not damage the airbag modules (for example only for this specific vehicle model. Do not use them on a pinning something onto them or pressing objects against their different vehicle model, as this may cause serious damage and covers). consequent injury, even fatal, to the occupants in the event of an If, for any reason, an airbag cover gets damaged, have the airbag accident. module immediately checked by your Authorized Ferrari Dealer. Warning Activation of a damaged module could cause serious or fatal injuries. Damaged or defective components of the airbag system cannot be repaired and must be replaced. Improper operations performed on the system components may Important note cause failures or accidental deployment or failure of the airbags Do not remove or dismantle parts of the steering wheel, to inflate with consequential damage and injury, even death. dashboard or door panels; if necessary, this procedure should only be performed by an Authorized Ferrari Dealer. Environment Important note To scrap the vehicle, please contact your Authorized Ferrari Dealer to have the airbag system deactivated. All the airbag system components must be replaced after an accident that caused airbag deployment. Important note Following an accident not involving airbag deployment, contact your Authorized Ferrari Dealer to have the system checked and any system components that may be damaged or malfunctioning replaced. 74 Safety

Important note Warning If the vehicle has been stolen or there has been an attempted Do not transport children in rearward facing child restraint theft, have the airbag system checked by your Authorized systems on the front passenger seat unless absolutely necessary. Ferrari Dealer. Although the front passenger airbag has been designed and developed not to cause injury, it should be stressed that the muscle and bone structure of children is not fully developed Important note and therefore vulnerable; the risk of very severe or even fatal The label E on the passenger-side sun visor bears the injury caused by activation of the airbag cannot therefore be airbag system expiration date. When this expiration date is approaching, contact your Authorized Ferrari Dealer in order excluded. 3 to have the system replaced. The label F indicates the presence of the airbag system. E F Safety 75

Passenger airbag deactivation Important note In this vehicle there is one way to deactivate the passenger airbag: Established legislation in some countries already provides use of dedicated Ferrari child seats that can be purchased at your that children under 12 years of age may not travel in the front Authorized Ferrari Dealer. passenger seat. Always require the proper child seat, specifically designed for the The label on the dashboard (see picture below), may be size of your child. removed only by the customer. BabySmartTM system: automatic deactivation of the passenger airbag with dedicated child seats (see also page 78). BabySmartTM is a trademark of Siemens Automotive Corp. 76 Safety

TAB 1- Dedicated Baby SmartTM child seat for Ferrari 458 Italia (Produced by Britax-Römer) Child height Child weight Child seat name Child seat type 31 inches 22 pounds BABY Plus Rearward facing: use only (See Picture 1) (80 cm) or less (10 kg) or less facing opposite the traveling direction Between 27 and 40 Between 20 and 40 DUO Plus Forward facing: use only (See Picture 2) inches (69÷102 cm) pounds (9÷18 kg) facing in the traveling direction 3 Picture 1 Picture 2 Warning Any time the Child Seat Presence and Orientation Detection (CPOD) restraint system needs to be tested, you must bring your child seat to an Authorized Ferrari Dealer. Safety 77

BabySmartTM system: automatic deactivation If the “PASSENGER AIRBAG OFF” warning light is not illuminated, of the passenger airbag with dedicated child seats the passenger airbag is enabled. (see also page 76) If the “PASSENGER AIRBAG OFF” warning light blinks at intervals Dedicated child restraint systems are designed to operate with the of 6 seconds, the passenger airbag is deactivated but only one of the BabySmartTM automatic child seat recognition system for the front two transponders on the child restraint has been recognized. This passenger seat of this vehicle. means that the child seat is damaged or not properly installed. In this Dedicated child seats operate as any other child safety seat, except for case, have the vehicle's BabySmartTM automatic child seat recognition the fact that they are designed to automatically deactivate the passenger system checked and the dedicated child seat replaced by your airbag on vehicles equipped with “Baby SmartTM” system. Authorized Ferrari Dealer. Dedicated child seats are equipped with two transponders that are located and recognized by special transmitters built into vehicle Warning front passenger seat. Never drive with a child in a child restraint in the front passenger When the dedicated child restraint is properly installed on the front seat if the “PASSENGER AIRBAG OFF” warning light on the passenger seat, the transponders are recognized by the transmitters roof panel is not illuminated. Airbag deployment can cause serious and the front passenger airbag is disabled. injuries or death to a child. The “PASSENGER AIRBAG OFF” warning light must be permanently Never place objects such as pillows or cushions underneath the illuminated when the ignition key is in position II and the BabySmart™ child restraint. The entire base of the child restraint must always be child restraint is installed on the front passenger seat, a warning will also directly resting on the seat surface. be temporarily viewed on the left TFT display Follow the instructions provided with the child restraint systems for proper installation. Instructions are located in a dedicated compartment on the child seat: - BABY Plus: at foot end of the seat; - DUO Plus: inside the pocket on the rear of the seat; You can be certain you have installed your child restraint or booster seat correctly by having it checked at a child safety seat inspection station or by a certified child safety technician. To find one near you, visit http://www.nhtsa.dot.gov/CPS/CPSfitting or www.seatcheck. org. You can also call 1-888-DASH-2-DOT or 1-866-SEATCHECK. 78 Safety

Warning Warning Never drive with a rearward-facing child seat installed in the Even if a dedicated child restraint is correctly installed in the travel direction (i.e., the child facing the front of the vehicle). The front passenger seat, if the “PASSENGER AIRBAG OFF” child restraint protective function is only ensured when the child warning light on the roof panel is not illuminated, the passenger restraint is both installed and used properly. Otherwise the child is airbag is enabled. Airbag deployment can cause serious injuries not properly secured and could be injured in the event of accident, or death to a child. If the front passenger airbag is not disabled, sharp braking or sudden changes of direction. do not transport children in this vehicle. Warning Have the BabySmartTM automatic child seat recognition system checked by an Authorized Ferrari Dealer if the 3 Never drive with a forward-facing child seat installed opposite the “PASSENGER AIRBAG OFF” warning light does not illuminate direction of travel (i.e., the child facing the rear of the vehicle). The when a dedicated child restraint is installed. child restraint protective function is only ensured when the child restraint is both installed and used properly. Otherwise the child Warning is not properly secured and could result in injury or death in the event of accident, sharp braking or sudden changes of direction. On vehicles with BabySmartTM system, do not place any electronic device on the front passenger seat, such as: - Active laptops; - Mobile phones; - Electronic toll payment devices; - Cards with transponders, e.g., ski passes or access authorization cards. Since the signals from electronic devices can interfere with the PASS AIR sensor system of the automatic child seat recognition system, BAG OFF they could cause the system to malfunction and result in the front passenger airbag failing to activate/deactivate. Safety 79

Side airbags Warning Warning When the ignition key is turned to position II, the warning light A will illuminate. If no malfunctioning in the airbag system is Airbags are not a substitute for seat belts but they increase their detected, it will go off after 4 seconds. If the warning light does efficiency. Correct use of seat belts, with the supplementary not illuminate, if it remains on or if it illuminates while driving, action of the side air bags, help provide protection in the event contact your Authorized Ferrari Dealer immediately. of a collision or certain vehicle roll-overs. Operation Side airbag system components The side air bags are controlled by the ECU designed to activate them when a sufficiently severe collision occurs. Warning In the event of a side collision with a force of impact exceeding the limit set by the ECU, the ECU is designed to transmit a signal that The side air bags fitted on the vehicle have not been designed activates the pretensioner and the side air bag on the impact side. to reduce the risk of being thrown out in the event of vehicle roll-overs. The vehicle has 2 side air bags, one in the driver-side door and the other in the passenger-side door. The side air bag system consists of 2 airbags, one on each door. In the event of certain side collisions of sufficient force, the airbag on the impact side is designed to deploy immediately to help protect A the occupant's head. 80 Safety

The airbag is designed to start deploying, opening its cover along the breaking line, until it is fully deployed (in a few hundredths Warning of seconds). After deployment, the side air bag is designed to act Never modify the airbag modules. Do not damage the airbag as a protection between the driver’s or passenger’s head and the modules and trim panels above them by pinning something external structures. The airbags deflate immediately afterwards. onto them or pressing objects against their covers, for example. Side air bag activation is not affected by the front passenger's If, for any reason, an airbag cover gets damaged, have the airbag height or weight. The side air bag is activated whenever the module immediately checked by your Authorized Ferrari airbag ECU detects a side impact collision of a sufficient force for Dealer. deployment. Activation of a damaged module could cause serious injuries. Warning 3 Never drive with your head out of the window as this places Important note your head and neck in the airbag deployment area. In the event The airbag ECU is not capable of automatically detecting any of a side collision, this position increases the risk of being damage to the airbag covers. thrown out of the vehicle and compromises the protective effect of the side air bags. Do not cover the upper part of the driver-door and passenger- door panels with adhesive tape or material and do not treat them in any way. Warning Never place an object over or near the airbag covers. Warning In the event that the airbags are deployed, these objects would After deployment, the airbag components can no longer offer be projected into the passenger compartment at such high speed any protection; therefore, they cannot be repaired and must be as to seriously jeopardize the safety of the occupants. replaced. After activation of a side air bag, have it replaced by your Authorized Ferrari Dealer. Safety 81

Warning Important note The airbag modules are subject to wear and tear and must be Never remove the door panel. If required, this operation must replaced at the intervals indicated in the “Warranty Book” EVEN be performed by your Authorized Ferrari Dealer. if the vehicle has NOT been involved in a collision. Important note The label E on the passenger-side sun visor bears the airbag system expiration date. When this expiration date is approaching, contact your Authorized Ferrari Dealer to have the system replaced. E 82 Safety

Fuel inertia switch The fuel inertia switch is a safety device which is designed to deactivate the fuel pump relays if a collision occurs. A symbol appears on the left TFT display and the hazard warning lights come on to indicate that the switch has been activated. When the fuel inertia switch is activated, the doors are also unlocked (if locked) and the central dome light comes on. Important note The fuel pump relays can be reactivated by pressing the button 3 A on the fuel inertia switch located in the battery compartment which can be accessed by opening the passenger side footrest. A Safety 83

ABS and EBD The system is designed to provide the following advantages: - Enhanced driving stability: even in the event of sharp braking The ABS system is a safety device which is designed to activate to approaching wheel locking. help prevent wheel locking if the driver presses the brake pedal too sharply, especially under low grip conditions. - Improved handling. The system is composed of: This means that even when an emergency situation requires sudden braking, the driver can avoid obstacles, or brake on a curve, without - electro-hydraulic unit affecting the vehicle stability. - electronic brake-force distribution EBD - four speed sensors on the wheels, incorporated in the bearings Warning - the entire ESP sensor system (steering angle sensor, accelerometer, yaw sensor, etc.). ABS system performance remains unaltered as long as the speed limit for the tire side grip is not exceeded. If this limit is These features add to the vehicle’s standard braking system, exceeded, vehicle skidding cannot be avoided. without changing its characteristics. Important note Warning When the ABS system is activated, during emergency braking The ABS system does NOT exempt the driver from driving or in poor grip conditions, a “pulsing” sensation will be felt carefully and responsibly at all times. through the brake pedal. This is a normal characteristic of the ABS system. Hold the brake pedal down to continue the braking action. Important note The ABS system cannot compensate for driving too fast for traffic or road conditions, worn tires, worn braking system components or driving errors. The ABS system has been designed for the sole purpose of assisting the driver in controlling braking under extreme conditions in which he/she might otherwise cause the wheels to lock. 84 Safety

FBP - FERRARI Brake Prefill - Level 3: (Manettino set to RACE) enhances the racing features of the vehicle by reducing engine control to a minimum and Brake design parameters provide a set distance between the maximizing brake control. This mode is designed to help ensure brake pads and discs (the “air gap”): as soon as the brake pedal is stability on the race track in high grip conditions only. pressed, the presence of the air gap leads to a slight delay in brake - Level 4: (Manettino set to CT OFF) further enhances the response. racing style performance of the vehicle: F1-Trac traction control The FBP (Ferrari Brake Prefill) system helps eliminate the air is deactivated whereas stability control remains active when a gap by applying slight pressure to the braking system as soon as certain level of sideslip is exceeded. F1-Trac traction control is off. the accelerator pedal is released just before braking. This results Stability is NOT guaranteed. in more immediate brake response and reduces braking distance during emergency braking thereby helping to improve safety. - Level 5: (Manettino set to CST OFF) CST off. Stability is NOT guaranteed, but all the other auxiliary systems such as the ABS, EBD and the E-Diff 3 electronic differential remain active. During 3 CST - Stability and Traction Control braking, the VDC system remains active. The CST is composed of two main systems: VDC Vehicle Dynamics Control, performed through the braking system F1-Trac traction control, performed through engine torque modulation, depending on maximum grip on the road and secondary systems that are always active such as the ABS and EBD. To help provide optimal control in different driving and grip conditions, five different settings have been developed: - Level 1: (Manettino set to Low-grip) ensures stability and maximizes traction on every type of road surface, both in low and very low grip conditions, by means of engine and brake control (in this condition, the standard ASR system is activated instead of the F1-Trac function). - Level 2: (Manettino set to SPORT) helps to ensure stability and maximizes traction only in medium- to high-grip conditions by optimizing engine and brake control. Safety 85

F1-Trac E-Diff 3 F1-Trac is a traction control system that derives directly from The vehicle is equipped with an electronic differential, working on Ferrari's expertise in F1 vehicles. the rear axle, which continually performs a variable check on the F1-Trac is faster and more accurate than traditional control locking between the two axle shafts. systems and is capable of delaying and minimizing engine torque The electronic differential system, integrated with F1-Trac traction adjustments as required in order to ensure the desired trajectory. control, is capable of improving: The system estimates the maximum available grip in advance, by - performance; continuously monitoring the relative wheel speed and using an - directional stability of the vehicle; auto-adaptive operating logic. Comparing this information with the - active safety even when close to grip limit; vehicle dynamics model stored in the control system, F1-Trac helps optimize the vehicle behavior by controlling engine torque delivery. - driving comfort and handling. The system is based on the analysis and forecast of vehicle Important note performance in almost all possible conditions. This is done by continually monitoring the pressure of the clutch actuator on the F1-Trac does not work when the Manettino is set to CT OFF differential. and CST OFF driving modes. The input signals are the dynamic parameters of the vehicle that the control system translates into a torque difference between the two The main feature that distinguishes the F1-Trac system from a driving wheels. traditional traction control system lies in its ability to estimate grip On corners, the electronic differential can: level accurately which allows the driver to make full use of the - stabilize the vehicle when the accelerator pedal is released by vehicle's performance driving potential. locking the rear axle; The F1-Trac system provides: - control vehicle dynamics by locking the differential according to - maximum traction when coming out of corners; lateral acceleration and vehicle speed; - driving stability and ease even under extreme driving conditions; - maximize vehicle stability and, at the same time, acceleration - driving comfort. on corners by locking the differential according to lateral On this vehicle, integration of the F1-Trac and E-Diff 3 systems acceleration, speed, engaged gear and torque produced by the helps to ensure maximum performance and stability. engine. To obtain these results, the electronic differential system interacts with the F1-Trac, CST, ABS systems, F1 gearbox and suspension damping control. 86 Safety

EPB - Electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. Always apply the parking brake when the vehicle is parked. The parking brake can be applied and released using the button B on the dashboard to the left of the steering wheel. A special If the vehicle is not held in place by the parking brake, please warning light illuminates on the instrument panel to indicate that contact your Authorized Ferrari Dealer. the parking brake has been applied (see page 133). It is deactivated by pushing down the brake pedal and pressing Autopark function button B. The warning light will go off when the parking brake has The EPB Autopark function automatically activates the electric 3 been released completely. parking brake when the engine is turned off. When the key is The electric parking brake can be used as an emergency brake turned to on, the Autohold function is always activated but can be when the vehicle is in motion. If this is the case, the system acts on temporarily deactivated by pressing the AUTO PARK C button. all four wheels until button B is released by communicating with When the C button is pressed, the message “PARK OFF” is the ESP system which prevents locking. displayed on the left TFT display for 5 seconds. If button C is pressed again, then the message “PARK ON” is displayed on the left TFT display for 5 seconds. “Automatic Vehicle Holding” AVH function The electric parking brake provides optimized release on hill starts due to its Automatic Vehicle Holding function: in certain circumstances, this system helps keep the vehicle stationary by using differentiated brake shoe/pad release so that there is time to move your foot from the brake pedal to the accelerator without the vehicle moving backwards. C B Safety 87

Tire temperature and pressure Warning monitoring system (TPMS) The vehicle is equipped with a system that measures the tire The TPMS warns the driver that the tire pressure has decreased. pressure and temperature using special sensors fitted inside the However, this does NOT exempt the driver from periodically wheel rims next to the air valve. These sensors transmit a signal checking that the tires are inflated to the indicated pressure. that is received by the antennas on the car body, behind the gravel In addition, the system does NOT warn the driver of damage to guards, that are connected to the ECU. the tires by external agents. Important note Displaying messages on the left TFT display The system may be momentarily affected by radioelectrical By using the commands on the left TFT display (see page 108), the interference from devices that use similar wavelengths. driver can access the TIRES screen page which displays the vehicle symbol with the pressure and temperature values of each tire as shown in example 1. The ECU processes this information and transmits data on tire pressure and temperature and any system errors to the instrument panel. The signal transmitted by the ECU activates symbols on the left TFT display (see page 108) with two priority levels: a soft warning (SW) if the pressure loss is 2.9 psi (0.2 bar) more than the rated pressure and a hard warning (HW) if it is 7.25 psi (0.5 bar) more or there is a dynamic decrease of over 2.9 psi/min (0.2 bar/min). The TPMS can be calibrated using the special menu item in the left TFT display (see page 110). 8 F 8 F psi psi Important note System calibration using the special menu item on the left TFT 8 F 8 F display is necessary after replacement or inflation of a tire or psi psi tires. 1 88 Safety

If an event occurs that needs to be displayed as a symbol and/ The screen page is displayed for 20 seconds and then the screen or special message when the TIRES screen page is displayed, page that was previously displayed reappears. If the failure persists, the screen page is reduced as shown in example 2. For further the screen page shown (example 3 or 4) will be automatically information, refer to the “Fault displaying logic” paragraph on displayed for 20 seconds the next time the engine is started. page 125. The driver can call up the TIRES screen page at any time to display which tires have low pressure (example 5). Low pressure Regardless of the type of screen page on the left TFT display, when the instrument panel receives the signal from the tire pressure ECU that the pressure level of one or more tires is below the alarm threshold, the screen page shown in example 3 (for a warning related to only one tire) or example 4 (for a warning related to 3 several tires) appears immediately. 8 F 8 F 8 F 8 F 8 F 8 F 8 F 8 F psi psi Check tire psi psi Check tire psi psi psi psi pressure pressure Catalysts temp. too high Engine performance 8 F 8 F 8 F 8 F 8 F 8 F 8 F 8 F psi psi psi psi psi psi psi psi limited 2 3 4 5 Safety 89

Occasionally, the system may not detect which wheel signals The screen page is displayed for 20 seconds and then the screen a failure. If this is the case, then only the message “Check tire page that was previously displayed reappears whereas the warning pressure” will be displayed as shown in example 6. light remains on. If normal tires are used, the failure follows the same display logic Tire puncture as the other priority level 0 faults (see the “Fault displaying logic” Regardless of the type of screen page on the left TFT display, when paragraph on page 125) until the situation is corrected and the the instrument panel receives the signal from the tire pressure system is recalibrated. ECU that the pressure level of one or more tires is below the If the vehicle is fitted with Run Flat tires, the maximum distance alarm threshold, the screen page shown in example 7 (warning allowed in a “tire puncture” state is 62 mi (100 km). The not to proceed for vehicles fitted with normal tires) or example 8 instrument panel will calculate the residual tire life and will (warning to proceed at a maximum speed of 50 mph (80 km/h) for redisplay the screen page shown in example 8 after 31 mi (50 km). vehicles fitted with Run Flat tires) appears immediately. At the same The same screen page (warning not to exceed a maximum speed time, a warning light illuminates on the instrument panel (see page of 50 mph) is displayed if the vehicle exceeds 50 mph (80 km/h). 131). Once the distance of 62 mi (100 km) has been exceeded, the panel displays the screen page shown in example 7 (warning not to proceed). If you call up the TIRES screen page, you can identify the punctured tire at any time (example 9). 8 F 8 F 8 F 8 F 8 F 8 F Check tire psi psi psi psi psi psi pressure Low tire Low tire pressure pressure Do not 8 F 8 F Max speed 8 F 8 F 8 F 8 F proceed psi psi 50 mph psi psi psi psi 6 7 8 9 90 Safety

If another tire is punctured, the instrument panel will update the Occasionally, the system may not detect which wheel signals a number of miles (km) which can still be driven according to the failure. If this is the case, the screen page shown in example 12 (for distance driven after the previous puncture and will display the vehicles fitted with normal tires) or example 13 (for vehicles fitted screen page shown in example 10. with Run Flat tires) will be displayed. While priority level 0 (normal tire puncture) or priority level 2 The symbol and message are displayed for 20 seconds and then the (Run Flat tire puncture with maximum speed limit not exceeded screen page that was previously displayed reappears whereas the and tires still usable) faults are being displayed, the driver can press warning light remains on. the OK button with “ESCAPE” function (see page 125): the screen If the vehicle is fitted with Run Flat tires, the instrument panel will page disappears whereas the warning light on the panel remains on. calculate the residual tire life and will redisplay the screen page As above, the TIRES screen page can be called up at any time to display which tires are punctured (example 11). shown in example 13 after 31 mi (50 km). The same screen page (warning not to exceed a maximum speed of 50 mph) is displayed if the vehicle exceeds 50 mph (80 km/h). Once a distance of 62 mi 3 (100 km) has been exceeded, the panel displays the screen page shown in example 12 (warning not to proceed). 8 F 8 F 8 F 8 F psi psi psi psi Low tire Low tire Low tire pressure pressure pressure Max speed 8 F 8 F 8 F 8 F Do not Max speed 50 mph psi psi psi psi proceed 50 mph 10 11 12 13 Safety 91

System not calibrated When the Menu item is displayed and the subsequent calibration If the system has not been calibrated or one or more tires have accepted, the screen page shown in example 15 appears for been replaced, the symbol and message shown in example 14 will 5 seconds. be displayed. At the same time, the warning light on the instrument panel (see page 131) will flash for 90 seconds. Warning When the display cycle ends (20 seconds), the symbol and message Before calibrating the system, make sure that the tire pressure disappear and the screen page that was previously displayed corresponds to the indicated pressure values (see page 31). If reappears whereas the warning light remains on until the system this is not the case, the TPMS may issue wrong low pressure has been calibrated. indications. The TPMS can be calibrated using the special menu item in the left TFT display with the ignition key in position II and the engine off. To calibrate the TPMS, call up the MENU screen page on the left TFT display (see page 110) with the ignition key in position II and the engine off. Once the MENU screen page appears, select the items “Car setup”, “Calibrate TPMS”. Display setup Date/Hour Calibration TPMS activated Language/M.U. not calibrated Execute Car setup calibration Dimming 14 15 92 Safety

TPMS failure At the same time, a warning light illuminates on the instrument The screen page shown in example 16 is displayed in the following panel (see page 131) flashing for 90 seconds. The warning light circumstances: then remains on until the situation is corrected. - malfunction in the circuit and/or wiring connecting the ECU The TIRES screen page cannot be called up by the driver. - signal is not received by one or more sensors due to a faulty, System not active broken or dead battery For a few seconds at key-on, if the TPMS has been deactivated by a - fault in the TPMS ECU. diagnostic tool, the screen page in example 18 is displayed. At the same time, a warning light illuminates on the instrument At the same time, a warning light illuminates on the instrument 3 panel (see page 131) flashing for 90 seconds. The warning light panel (see page 131) flashing for 90 seconds. The warning light then remains on until the situation is corrected. then remains on until the situation is corrected. The TIRES screen page cannot be called up by the driver. The TIRES screen page cannot be called up by the driver. System temporarily not active The screen page shown in example 17 is displayed in the following circumstances: - overheating of sensors - during calibration (the TPMS ECU does not recognize the sensors) - radio frequency that interferes with the wheel sensor signal. TPMS failure TPMS TPMS inactive temporarily inactive 16 17 18 Safety 93

Doors ................................................................... 96 Engine compartment lid......................................... 97 Luggage compartment lid ...................................... 98 Ignition switch ..................................................... 101 Fuel filler flap and neck ........................................ 102 Power windows ................................................... 104 Instruments and gauges ....................................... 106 Controls on the steering wheel ............................. 140 Lighting system.................................................... 146 Driving the vehicle ............................................... 152 EPB - Electric parking brake ................................. 170 Park Lock ............................................................ 172 Performance Start ............................................... 173 Seat adjustment .................................................. 176 Air conditioning and heating system ..................... 184 Passenger compartment accessories ..................... 188

4 ABOUT YOUR VEHICLE

Doors Locking and opening the doors from the inside When a door is opened or closed, the window automatically moves down by approximately 0.8 in. / 2 cm (to its “target position”) to Warning avoid damaging the upper weather strip. Always carefully check manually that the doors have been When the door is closed, the window automatically moves up until closed properly to prevent them from opening while driving. it reaches the “upper limit”. Both doors can be locked by activating/deactivating the “LOCK/ Opening from the outside UNLOCK” button B on the roof panel. To lock the doors, press Using the remote control, deactivate the alarm and the central door button B; when the door lock is activated, the light on button B locking system, or turn the key in the lock to deactivate the central comes on. To deactivate the door lock, press button B until the door locking system. light goes out. To open the door, pull handle A: the window will move down to its A function that automatically locks the doors when the vehicle is target position. When the door is closed, the window will move up moving at a speed of 12 mph (20 km/h) or over can be activated until it meets the upper limit. on the “Car setup” menu on the left TFT display of the instrument panel (see page 110). B � C 96 About your Vehicle

If you pull handle C to open the door, the window will move down Engine compartment lid to its target position. When the door is closed, it will move up until it meets its upper limit. Opening If handle C is lifted without opening the door, the window will Pull release lever D on the driver-side internal sill. move down to its target position and stop and if the door is not Lift the engine compartment lid. The lid is held open by two gas opened after 2 seconds, the window will move back up until it struts E. meets the upper limit. Therefore, to open the door, release handle The engine compartment lid can also be opened with the ignition C and pull it again. key off. When the opening handle is operated, both doors are unlocked. Closing Lower the lid completely and press down near the lock until you hear it click in place. Warning Always check manually that the engine compartment lid has 4 been closed properly to prevent it from opening while driving. E D E About your Vehicle 97

Luggage compartment lid Important note Opening After removing the battery from the vehicle or disconnecting The luggage compartment lid can also be opened with the ignition it from the electrical system, a door lock/unlock cycle must be key off. performed using the buttons on the key when reconnecting so Push release button F on the left edge of the driver-side floor or that the release button F resumes normal operation (electronic press button G on the ignition key for more than 2 seconds. system self-acquisition procedure). Stand in front of the vehicle, slightly lift the lid and pull the retaining lever H to lift it completely. The lid is held open by two gas struts L. The luggage compartment is illuminated by an internal light that comes on automatically when the luggage compartment lid is opened. G F H 98 About your Vehicle

Closing Emergency Opening Lower the lid completely and press down near the lock until you If the luggage compartment lid opening button does not work, hear it click in place. there is a cord for manual emergency opening underneath the dashboard to the left of the steering wheel as shown by the arrow in the figure. Warning Always check that the luggage compartment lid has been closed properly to prevent it from opening while driving. 4 L L About your Vehicle 99

Emergency exit from inside the luggage compartment If someone remains closed inside the luggage compartment accidentally, the luggage compartment lid can be opened from the inside by pulling the handle M, located on the inside of the luggage compartment. M 100 About your Vehicle

Ignition switch Warning The ignition key can be turned to 2 positions: Position 0 - Stop Never remove the key when the vehicle is moving! Engine off, key removable. The steering wheel will lock with the first rotation of the steering wheel. When the key is even only partially extracted, the steering column is locked. Always remember to remove the key from the ignition when you get out of the vehicle! The hazard warning lights and parking lights can be activated. Never leave people who are more subject to injury unattended To facilitate steering wheel release, turn the steering wheel slightly in the vehicle. clockwise or counterclockwise while turning the ignition key. Position II - Start Key lock When the key is turned to this position (key-on) the signals If more than 20 seconds elapse after turning the key to position 0, generated by the vehicle systems are checked. The left and right TFT displays are activated on the instrument the key lock device must be released to remove the key: press button K and remove the key at the same time. 4 panel and when the signals have been checked, the gearbox display comes on (see page 134). K II 0 About your Vehicle 101

Fuel filler flap and neck Emergency Opening If the opening button does not work, the fuel filler flap can be opened manually by pulling the cable P on the right-hand side of Warning the engine compartment. Always turn off the engine during refueling. Do not smoke or use open flames when refueling. The following can be harmful for your health: - fuel coming into contact with your skin - inhaling fuel vapors. Opening To open the fuel filler flap, press button M on the left edge of the driver-side floor. Closing To close the fuel filler flap, push it until it clicks in place. M P 102 About your Vehicle

Capless filler neck This vehicle has a capless filler neck for fuelling. This system allows Warning you to refuel by opening the fuel filler flap and simply placing the Place the nozzle in the filler neck carefully to avoid damaging nozzle in the filler neck without having to unscrew a cap and screw the device seal. it on again. Do not try to open the external flap of the filler neck by pushing Two flaps placed in series, both with airtight seals, act as a cap. The it with your fingers or lever it open using unsuitable tools (e.g., external flap is locked by a series of “teeth” and the only way to screwdrivers). This may damage the external flap mechanism open the external flap correctly is by inserting a fuel pump nozzle. and the seal. Warning Do not overfill the fuel tank: this may cause the fuel to leak out. After fueling, wait for about 5 seconds before slowly removing the nozzle from the filler neck: in this way, the last drops of fuel will flow into the tank and will not drip onto the vehicle. 4 Warning Do not place funnels or portable container nozzles in the filler neck. If you need to refuel from a portable fuel container, use only the funnel supplied in the tool bag (see page 194) that releases the automatic closing device. About your Vehicle 103

Power windows Passenger-side power window The power windows can only be operated with the ignition key in Press button B to move the window up or down. position II. Only manual operation is possible (partial opening) to raise the Driver-side power window window: when button B is released, the window stops at the position reached. Press button A to move the window up or down. To lower the window, automatic operation is also possible (full This allows manual operation (partial opening/closing) or opening): if the button is pressed at length (over 0.3 seconds) automatic operation (complete opening/closing): press button A automatic window operation is activated. The window will only and quickly release to activate manual operation; if the button is stop when it reaches the end of its travel or by pressing the button pressed at length (over 0.3 seconds), automatic window operation again. is activated. The window will only stop when it reaches the end of its travel or by pressing the button again. When the door is open, the window moves down to its “target position”; this is to prevent the window from damaging the upper weather strip when it is closed. B A 104 About your Vehicle

Warning Pay particular attention during the operation of the driver- side power window, because the window will open / close automatically when the feature is activated. Improper use of the power windows can be dangerous. Before use, always check that people and objects are at a safe distance. To protect the passengers remaining in the car against accidental activation of the power windows, always remove the key from the ignition. 4 About your Vehicle 105

Instruments and gauges 6 5 2 5 3 7 1 5 4 5 106 About your Vehicle

1 Left TFT display 2 Tachometer 3 Right TFT display 4 Gear display 4 5 Warning lights on the panel 6 Manettino status 7 Fuel level About your Vehicle 107

MAIN screen page Warning If you press the MAIN button, you activate the MAIN screen page When using the TFT display and its controls, do not become which can be used to access the four screen page groups SETUP, distracted from driving the vehicle. When possible, perform VDA, TRIP and STATUS. These groups contain the following screen these operations with the vehicle stationary. pages: SETUP (pressing the UP button) Left TFT display MENU screen page Located on the instrument panel, it performs the following STATUS (pressing the DOWN button) functions: SPORT screen page - displays the control parameters SPORT 2 screen page - displays general information while driving TIRES screen page - displays fault warnings. VDA (pressing the LEFT button) The driver can interact with the system by selecting the Chronometer screen page configuration and setting the parameters using the controls on the Vehicle status screen page dashboard to the left of the steering wheel. Manettino status screen page The display is activated and set by pressing the MAIN (A), VDA (B), TRIP (pressing the RIGHT button) OK (C) and UP, DOWN, LEFT, RIGHT (D) buttons. TRIP A screen page TRIP B screen page B A C D 108 About your Vehicle

Press the RIGHT and LEFT buttons to sequentially switch between Every screen page consists of four display areas: screen pages in a group. Press RIGHT to go to the next screen page A - selected driving mode (Manettino position), windshield wiper (for example, in the STATUS group from SPORT to SPORT 2) status, outside temperature and “Warning: danger of ice” icon and press LEFT to go to the previous screen page. Press the RIGHT B - display of virtual control gauges, parking sensor screen page, button after the last screen page to go back to the first screen page display of abnormal events/warnings (message text and special and press the LEFT button after the first screen page to go back to symbol, when available), display of brightness adjustment the last screen page. function When a screen page is called up, it remains on the display until you C - total or trip odometer (TRIP A or B), range decide to select another one. D - fuel level gauge, area for minimized symbol for faults that do not have a specific warning light on the instrument panel (see page 125), speed repetition. 4 About your Vehicle 109

Display setting and configuration of vehicle parameters Navigation within the menu is on several levels; the first level offers a list of items through which the following parameters can be set or the following information can be displayed: Warning - Dimming: display dimming setting Display setting and parameter configuration should be - Display setup: display setting performed when the vehicle is stationary. - Date/Hour: date and time setting - Language/M.U.: language and units of measurement setting MENU screen page - Car setup: vehicle parameter configuration Display setting and configuration of the various vehicle parameters - Calibr. TPMS: TPMS calibration is possible using the MENU screen page (the only screen page in - Service: information on scheduled maintenance. the SETUP group) that can be directly called up by pressing the UP button when the MAIN screen page is activated. These items are the main menu functions. To scroll through the list of items, press the UP and DOWN buttons; to select the required function, press and quickly release the OK button or the RIGHT button. Display setup M.U. Distance Date/Hour M.U. Temp. Language/M.U. Language Car setup M.U. Pressure Dimming 110 About your Vehicle

Once the function has been selected, the individual subfunctions or The first time one of the two buttons is pressed, the screen page parameters that can be activated are displayed. To select them, use is displayed. The next time the buttons are pressed, the brightness the UP and DOWN buttons and press and quickly release the OK can be adjusted. (or RIGHT) button to activate a subsection or activate the selected The adjustment made, which can be activated even when the parameter. vehicle is moving, can be seen immediately and does not affect the To go back to a previous level in the menu hold down the OK brightness of the warning lights on the instrument panel. button, press the LEFT button or select the BACK item which is The screen page disappears when the OK button is pressed or normally in the list of subfunctions. If no operation is performed automatically if it is not used for 5 seconds and is replaced by the for at least 10 seconds, the first menu level reappears on the screen page that was previously displayed. display. Adjusting brightness Warning The brightness of the two TFT displays on the instrument panel When using the TFT display and its controls, do not become can be adjusted by selecting the special item on the MENU screen page or by using directly the UP and DOWN buttons when the MENU screen page is not displayed and when the chronometer is distracted from driving the vehicle. When possible, perform these operations with the vehicle stationary. 4 off if the Chronometer screen page is displayed. DIMMING About your Vehicle 111

Fuel level gauge In limited cruising range conditions, the information on driving range in mi is replaced by the words “Limited cruising range”. The fuel level gauge is always displayed in area D of the display (see page 109). The gauge has 9 orange bars that gradually “turn off” as the fuel level drops. When the second bar goes off, the first bar turns red until fuel runs out. In “Fuel level low” condition, a warning light illuminates on the instrument panel (see page 128) and a special symbol and message are displayed for 10 seconds together with information on driving range in miles. If the condition that has generated it persists, this signal is repeated every 5 miles (8 km). Fuel level Fuel level Low low Limited Range cruising 56 mi range 112 About your Vehicle

SPORT screen page SPORT 2 screen page The SPORT screen page displays the following virtual gauges: The SPORT 2 screen page displays the following virtual gauges: - Engine coolant temperature - Engine oil pressure - Engine oil temperature - Voltmeter If the SPORT screen page is being displayed and an event occurs If the SPORT 2 screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the that needs to be displayed as a symbol and/or special message, the virtual gauges are minimized. For further information, refer to the virtual gauges are minimized. For further information, refer to the “Fault displaying logic” paragraph on page 125. “Fault displaying logic” paragraph on page 125. 4 About your Vehicle 113

TIRES screen page VDA (Vehicle Dynamic Assistance) screen page group The TIRES screen page displays the vehicle symbol and indicates In addition to its chronometer function, the Vehicle Dynamic the pressure and temperature values for each tire. Assistance (VDA) screen page group provides a valid support for If the TIRES screen page is being displayed and an event occurs assessing vehicle status when on the track and can be used to that needs to be displayed as a symbol and/or special message, intuitively understand the most suitable conditions for performance the screen page is minimized. For further information, refer to the driving. The VDA group, which is recalled by pressing the LEFT “Fault displaying logic” paragraph on page 125. button with the MAIN screen page displayed or directly by pressing the VDA button with any screen page displayed, consists of the “Chronometer”, “Vehicle status” and “Manettino status” screen pages. The “Vehicle status” screen page functions are only available when the “Manettino” driving mode control switch (see page 140) is set to RACE, CT OFF or CST OFF, positions developed especially when using the vehicle on track; however, if the Manettino is set to Low-grip or SPORT mode, the “Vehicle status” screen page is displayed along with the message “VDA available in Race - CT off - CST off”. VDA available in RACE - CT - CST 8 F 8 F psi psi 8 F 8 F psi psi 114 About your Vehicle

Chronometer screen page During display of the event/malfunction, the chronometer remains The “Chronometer” screen page is used to time laps and memorize active. lap time if the vehicle is used on track. The screen page displays the Each time the key is turned to on, the chronometer is reset whereas following information: the last valid Best Lap and Last Lap information is memorized. Current Lap indicates the time elapsed since the start of the chronometer Chronometer operating logic LAP TIME/Best The chronometer is controlled using the OK, UP and DOWN indicates the time taken to complete the last best lap buttons that perform the following functions: LAP TIME/Last - Pressing and quickly releasing the OK button: indicates the time taken to complete the last lap when the chronometer is off, starts the Current Lap chronometer TOP SPEED/Best indicates the maximum speed reached when the chronometer is on, resets and restarts the Current Lap and updates the information on previous laps (end of lap/start of TOP SPEED/Last indicates the maximum speed reached in the last lap next lap) - Pressing and quickly releasing the UP or DOWN button: 4 If the “Chronometer” screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special when the chronometer is on, stops the chronometer and updates message, the screen page is minimized. For further information, information on previous laps refer to the “Fault displaying logic” paragraph on page 125. when the chronometer is off, displays the screen page for adjusting display brightness - Holding down the UP or DOWN button: when the chronometer is on or off, resets the chronometer and information on previous laps. LAP TIME Note that during display of an event/malfunction, pressing and Best: 1:11:00 Current LAP Last: 1:14:40 quickly releasing the OK button interrupts the event/malfunction 1:12:10 TOP SPEED display cycle (“ESCAPE” function), without affecting the Best: 247 Km/h chronometer. Last: 230 Km/h About your Vehicle 115

Vehicle status screen page OVER The “Vehicle status” screen page, which is directly called up by One or more systems have reached an overheating condition pressing the VDA button or by pressing the LEFT button when the that may affect vehicle dynamics. Slowing down is therefore MAIN screen page is displayed, is intended to help the user bring recommended to restore these systems to optimum conditions of the vehicle to optimum performance when driving on high grip use. surfaces. This is made possible by an algorithm that determines the thermal state of the main vehicle subsystems (tires, brakes and engine) in relation to the dynamics of various parameters (lateral acceleration, speed, etc.). The status of the vehicle is displayed concisely using three levels which are blue, green and red: WARMUP WARMUP GO OVER Warm-up stage for components and self-acquisition of control systems; during this stage, the vehicle should be driven so that it is taken to optimum conditions of use. GO The vehicle has completed the warm-up stage: all its subsystems have reached optimum conditions of use for performance driving. WARMUP GO OVER WARMUP GO OVER 116 About your Vehicle

After each start, the CST stability and traction control system If one or more signals related to the performance parameters used compensates for the tire rolling radius and detects the spare to calculate the thermal state of the subsystems (lateral acceleration, wheel. While this procedure is being performed, the Vehicle Status speed, etc.) are not valid, the Vehicle Status screen page indicates screen page indicates to the driver that system self-acquisition is in to the driver that the function is not available by displaying the progress by displaying the message “CST autolearning”. message “Function not available”. Warning Use of the vehicle on race tracks: after each start, cover the first straight stretch of the track (at least 0.3 mi/500 meters) at a constant speed so that the CST stability and traction control system can calculate exactly the grip available and the rolling radius of the tires (the calculation is reset every time the engine stops). If this rule is not followed, system performance may be reduced. 4 CST Autolearning Function not available About your Vehicle 117

Manettino status screen page If one of the other two VDA screen pages is displayed The “Manettino status” screen page displays a list of parameters (“Chronometer” or “Vehicle Status”), the “Manettino Status” screen which can be configured using the “Manettino” driving mode page is displayed in timed mode for 3 seconds when the position of control switch (see page 140) and indicates the configuration each the Manettino is changed so that the driver is informed of the new one assumes in a specific driving mode. status that the systems are in. After 3 seconds, the screen page that was previously displayed reappears. The systems involved are the following: The “Manettino status” screen page is also automatically displayed - F1-Trac: traction control in timed mode at key-on if one of the other two VDA screen pages - E-Diff: electronic differential was displayed at the previous key-off and the Manettino was in a - F1-DC: dual clutch F1 gearbox different position from the current one. - CST: stability and traction control - ABS: anti-lock braking system Important note - SCM: magnetorheologically controlled suspension If there is a Manettino failure, the “Manettino Status” screen page cannot be displayed or recalled. VEHICLE DYNAMICS F1-Trac E-Diff F1-DC CST ABS SCM 118 About your Vehicle

TRIP A and TRIP B screen pages The TRIP A or TRIP B screen page displays the following information: - Maximum speed - Average speed - Travel distance - Travel time - Range If the TRIP A or TRIP B screen page is being displayed and an event occurs that needs to be displayed as a symbol and/or special message, the screen page is minimized. For further information, 4 refer to the “Fault displaying logic” paragraph on page 125. TRIP A Mon 16 Nov Maximum speed 93 mph Average speed 64 mph Travel distance 192.8 mi Travel time 03:36 h:m Range 204 mi About your Vehicle 119

“Warning: danger of ice” message When the minimum limit of 19 mph (30 km/h) is reached, press To warn the driver of the presence of ice on the road if the outside the DOWN button again to deactivate the function or press the UP temperature is 38 °F (3 °C) or below, the “snow” symbol and the button after reaching the maximum speed of 155 mph (250 km/h). “warning: danger of ice” message are displayed for 10 seconds in The function is normally deactivated (OFF). the top right of the display. When the set limit is exceeded, the driver is informed in the When they are displayed, the symbol and message appear instead of following way: the outside temperature; after 10 seconds, the outside temperature The symbol showing the set limit and a “speed limit exceeded” is displayed again and the “snow” symbol appears next to it as long message appear in the top right of the display for 10 seconds as the outside temperature remains 43 °F (6 °C) or below. accompanied by an acoustic signal. Once the warning cycle has ended, the message disappears whereas the symbol continues to be Speed limit setting and displayed next to the outside temperature until the speed decreases “Speed limit exceeded” message to 3 mph (5 km/h) below the set limit. The MENU screen page can be used to set a speed limit in the range 19 - 155 mph (30 - 250 km/h) with 3 mph (5 km/h) steps which sends a message to the driver when exceeded. To set the speed limit, call up the MENU screen page by pressing the UP button when the MAIN screen page is activated. Select “Car setup” and “Speed limit”. To set the value, use the UP and DOWN buttons. Warning: Speed limit danger of ice exceeded 120 About your Vehicle

Parking sensors (optional) The rear parking sensors are automatically activated when the key is in position II and reverse gear is engaged. When the rear sensors To help the driver when parking, the vehicle can be fitted on are activated, an acoustic signal warns the driver that the system has request with four sensors in the rear bumper (rear parking been activated. If the vehicle is also equipped with front sensors, sensors), or four sensors in the front and rear bumpers (front and these can be activated or deactivated by pressing the appropriate rear parking sensors). button on the roof panel (see page 151). Warning “Stop and Go” function The system will only operate correctly if the sensors on the The “Stop & Go” function, available on vehicles with front and bumpers are free of mud, dirt, snow or ice. rear parking sensors, automatically activates the front sensors when vehicle speed is 6 mph (10 km/h) or below. This system has been designed to assist the driver in certain traffic conditions When approaching obstacles in front of or behind the vehicle, (e.g., tailgating) and signals when the minimum distance is reached the parking sensors inform the driver of the distance between the between the vehicle and the vehicle in front. vehicle and the obstacle by way of acoustic signals, which become more frequent as the obstacle approaches, and visual signals in area To activate or deactivate the system, call up the MENU screen page, select the items “Car setup”, “Parking sensor”, and select one of the 4 B of the left TFT display (see page 109). By supplementing the driver's direct visual information with that provided by the system two options, “STOP&GO ON” and “STOP&GO OFF”. acoustic signals and visual warnings, potential collisions can be avoided when parking. Indication of obstacles The parking sensor system emits acoustic signals as soon as an Warning obstacle is detected which become more frequent as the obstacle approaches. The acoustic signal stops immediately if the distance It is the driver who holds full responsibility for parking from the obstacle increases whereas the tone cycle remains maneuvers and other potentially dangerous situations. The constant if the measured distance from the central sensors remains system has only been designed as an aid during parking unchanged. maneuvers since it detects obstacles that are outside the driver's The vehicle symbol and sensor detection zones appear on the field of vision. left TFT display: these zones indicate which part of the vehicle Use of the sensors therefore does not mean that the driver can is approaching an obstacle (if front or rear and if left, right or be less careful and attentive and not watch out for persons and center) and the distance from the obstacle (maximum, medium or obstacles during parking maneuvers. minimum). About your Vehicle 121

If an obstacle is detected at maximum distance in the central front If an obstacle is detected at minimum distance in the central front part, it will be displayed as shown below (green). part, it will be displayed as shown below (red). If an obstacle is detected at medium distance in the central front The maximum, medium and minimum distances between obstacles part, it will be displayed as shown below (yellow). and the vehicle, represented graphically by the colors green, yellow and red, differ between the rear and front parking sensors: Rear parking sensors: Maximum distance (green): between 31.5 and 27.5 in. (80 and 70 cm) (central area between 59 and 27.5 in.) Medium distance (yellow): between 27.2 and 16.2 in. (69 and 41 cm) Minimum distance (red): between 15.8 and 0 in. (40 and 0 cm) Front parking sensors: Maximum distance (green): between 28.8 and 20.8 in. (73 and 53 cm) (central area between 43.3 and 27.5 in.) Medium distance (yellow): between 20.5 and 12.2 in. (52 and 31 cm) Minimum distance (red): between 11.8 and 0 in. (30 and 0 cm) 122 About your Vehicle

If the front sensors are deactivated or not present, the display does If the parking sensor system symbols are being displayed and an not show the symbols in the front. In the same way, if front sensors event occurs that needs to be displayed as an icon and/or special are fitted and the rear ones are not activated, the display only message, the symbol is moved from the center of the display to the shows the symbols in the front. If all the sensors are activated, the right as shown below. system can give several pieces of information at the same time: if an obstacle is detected at a maximum distance in the front central Cleaning the sensors part and at a minimum distance in the rear right part, it will be displayed as shown below. Warning When cleaning the sensors, be very careful not to scratch or damage them and avoid using dry, rough or hard cloths. The sensors must be washed with clean water and car shampoo 4 added if necessary. In car washes that use steam jet or high pressure water cleaning equipment, quickly clean the sensors keeping the nozzle at a distance of at least 4 in. (10 cm). For the repainting of bumpers or retouching the paintwork in the sensor area, contact your Authorized Ferrari Dealer. If paint is applied incorrectly, it may prevent the parking sensors from working properly. Catalysts temp. too high Engine performance limited About your Vehicle 123

Indication of parking sensor failure The system ECU checks all the components each time the reverse Important note gear is engaged. If at least one parking sensor is faulty, the special The signals sent by the sensors may also be affected by damage symbol (see page 132) is displayed on the left TFT display together to the sensors caused by dirt, snow or ice on the sensors or with the message “Parking sensor failure. Warning! Possible by ultrasound systems (e.g., pneumatic brakes on trucks or obstacles” accompanied by an acoustic signal. pneumatic drills) in the vicinity. Important note The sensors are designed to detect obstacles with reasonably Warning large, even surfaces (e.g., poles with diameters of over 2.36 in. It is the driver who holds full responsibility for parking (60 mm), walls, barriers, trees). Detection is not optimum with maneuvers and other potentially dangerous situations. The obstacles with sharp projections or uneven surfaces. system has only been designed as an aid when parking since it detects obstacles that are outside the driver's field of vision. The sensors are therefore not a substitute for the driver's care Important note and attention when parking and checking for the presence of During parking maneuvers, always take the utmost care since persons or objects. obstacles may be located above or below the sensors. Important note Objects placed close to the rear part of the vehicle are not always detected by the system and may therefore damage the vehicle or be damaged themselves. 124 About your Vehicle

Fault display The warning light remains on until the cause of malfunctioning has been resolved. Fault displaying logic If the fault is resolved within 20 seconds, it remains displayed and When a fault occurs, the corresponding warning light (if present) the warning light remains lit for 2 seconds. illuminates on the instrument panel and a description of the fault (if available) and the relevant symbol (if available) are displayed “ESCAPE” function on the left TFT display. The message appears on the display at the Displaying a fault on the screen can be interrupted by pressing and same time as the warning light (if present) and the main screen quickly releasing the OK button with “ESCAPE” function. When page that is displayed at that moment is reduced. the OK button is pressed, the screen page that was displayed prior The fault remains on the display for 20 seconds. When the display to the event reappears. If the fault does not have a special warning cycle ends, if the fault does not have a special warning light on the light on the instrument panel, the symbol remains minimized in instrument panel, the symbol remains minimized in area D of the area D until the cause of malfunctioning has been resolved. display (see page 109) until the cause of malfunctioning has been resolved. In area B the main screen page is displayed in “maximum” size. 4 When the display cycle ends, if the fault has a special warning light on the instrument panel, the screen page that was displayed prior to the event reappears and the symbol is not minimized in area D. Catalysts temp. too high Engine performance limited About your Vehicle 125

Fault priority levels Indication of turn indicators and running lights failure The simultaneous display of several faults follows a logic that A failure of the running lights (front and/or rear) and turn depends on the priority level assigned to it: indicators (front and/or rear) is indicated in the same way as Priority level 0 - Extremely critical fault other faults but the vehicle symbol with the faulty running light or turn indicator is indicated in red and displayed together with Priority level 1 - Critical fault a description of the failure instead of the “External lights failure” Priority level 2 - Non-critical fault symbol (see page 129). When the display cycle ends or the OK When several fault events occur at the same time, faults with button with “ESCAPE” function has been pressed, the “External priority level 0 are displayed first, followed by priority level 1 lights failure” symbol is minimized. and then priority level 2. The information on the various faults is displayed in turn for 5 seconds each. In any case, the total display time for each fault is never less than 20 seconds. If a fault message with priority level 1 or 2 is being displayed, the priority level 2 message is only displayed once the priority level 1 message has been displayed for at least 2 seconds. If, on the other hand, another new priority level 0 fault occurs, this is displayed immediately. Lamp Failure 126 About your Vehicle

“Doors, engine or luggage compartment lid open” function display If one or more doors or the engine and/or luggage compartment lid are open, the vehicle symbol appears on the display and indicates which doors or lids are open together with a special message. If the vehicle is in motion, an acoustic signal is also emitted. When the display cycle ends or the OK button with “ESCAPE” function has been pressed, the special symbol is minimized (see page 117). 4 Doors open About your Vehicle 127

List of left TFT display symbols and warning lights on the Alternator failure instrument panel If there is a fault in the recharging system (priority level 1). TFT Warning Description and warnings Low windshield washer fluid level light Indicates a low level of washer fluid in the windshield washer tank (priority level 2). Alarm system failure Indicates a fault in the alarm system (priority level 1). Oil temperature The system is not programmed (priority level 2). Indicates that the oil temperature is too high (priority level 0). Failure and system not programmed (priority level 1). Turn off the engine and contact your Contact your Authorized Ferrari Dealer. Authorized Ferrari Dealer. Alarm system failure (priority level 2). Adaptive headlights failure Break-in attempted (priority level 2). Symbol and flashing warning light indicate there is Low fuel a failure in the adaptive headlight system (priority Indicates that the fuel level is too low (priority level 2). level 2). Windshield wiper motor failure Battery conditioner connected Indicates a windshield wiper motor failure When the instrument panel is on, it indicates that the (priority level 2). battery conditioner is connected (priority level 0). Engine coolant temperature Inertia switch Indicates that the engine coolant temperature is too Indicates activation of the inertia switch following high (priority level 0). an accident and the resulting cut-out of the fuel supply (priority level 0). Turn off the engine and contact your Authorized Ferrari Dealer. The hazard warning lights are also automatically activated. 128 About your Vehicle

Oil pressure External lights failure Indicates that the engine oil pressure is too low Indicates a system fault or burning-out of a bulb (priority level 0). in the running, turn indicator or rear fog lights (priority level 2). Turn off the engine and contact your Authorized Ferrari Dealer. License plate lights failure Indicates a system failure or burning-out of the A flashing warning light indicates an engine oil license plate light bulb (priority level 2). pressure sensor failure (priority level 2). Rear fog lights On board diagnostic system (OBD) When the rear fog lights are turned on. While the engine is running, it indicates a fault in Twilight sensor failure the emission control system and in the ignition/ Indicates a twilight sensor failure (priority level 2). injection system (priority level 0). Turn off the engine and contact your High beams When the high beams are turned on. 4 Authorized Ferrari Dealer. When the high beams are used to flash. After turning the ignition key to position II, it Right turn indicator remains on for a normal self-check for approx. 20 seconds after the engine has started. When the right turn indicators are activated. Running lights Left turn indicator When the running lights or low beams are turned When the left turn indicators are activated. on. Stop lights failure Indicates a system failure or burning-out of the STOP light bulb (priority level 2). About your Vehicle 129

Hazard warning lights ABS Simultaneous flashing of the right and left turn Indicates an ABS system failure (priority level 1). indicator warning lights indicate that the hazard warning lights have been activated. The standard braking system is still functioning. Catalytic converter temperature Contact your Authorized Ferrari Dealer. Indicates that the catalytic converter temperature is ASR + CST on excessively high: stop the vehicle as soon as possible (priority level 0). The symbol (displayed for 5 seconds together with the “CST on” message) indicates that the ASR and Contact your Authorized Ferrari Dealer. CST systems are active (priority level 1). ASR + CST off Indicates that the catalytic converter temperature is very high: reduce speed until the symbol goes out The symbol and warning light indicate that the ASR (priority level 1). and CST systems are deactivated (priority level 1). Indicates a failure of the catalytic converter The symbol is displayed for 5 seconds together with temperature sensor (priority level 0). the “CST off” message. Checking the engine oil level ASR/CST system failure Indicates a low engine oil level (priority level 0). Indicates an ASR/CST system failure (priority level 1). Seat heating Indicates that heated seat function is enabled Warning (remains displayed for 5 seconds). Stop the vehicle avoiding sharp braking. Stop Power steering failure driving and contact your Authorized Ferrari Indicates that the power steering system is Dealer immediately. inefficient (priority level 2). Contact your Authorized Ferrari Dealer. Warning The vehicle can still be driven at low speed, max. 25 mph (40 km/h) to leave the road. 130 About your Vehicle

ASR/CST system activation (flashing warning light) Airbag system failure Indicates that the ASR/CST system has activated Indicates a system failure (priority level 0). (priority level 1). With the warning light flashing, it indicates that the CCM brake discs worn airbag test cycle has not been completed (priority level 0). Indicates that the carbon ceramic brake discs are worn (priority level 2). Contact your Authorized Ferrari Dealer. Contact your Authorized Ferrari Dealer to Driver-side seat belt not fastened have the brake pads replaced. Indicates that the driver-side seat belt has not been fastened (priority level 0) together with an acoustic TPMS signal lasting 90 sec. Indicates a puncture in one or more standard tires 4 (priority level 0) or Run Flat tires (priority level 2). Speed limit exceeded With the warning light flashing for a maximum of Indicates that the speed set by the driver has 90 seconds after which it remains on indicates: been exceeded (priority level 2), the figure shown indicates the set speed. A failure in the TPMS (priority level 2). TPMS temporarily inactive (priority level 2). E-Diff system failure E-DIFF TPMS inactive (priority level 2). Indicates an electronic differential failure TPMS not calibrated (priority level 2). (priority level 1) E-DIFF Doors/front and rear lids open Cruise Control The symbol, which is minimized, indicates that one Indicates that the Cruise Control has been or more doors and/or lids are open. activated/deactivaded About your Vehicle 131

Brake malfunction Front Lift system failure Indicates that the brake fluid level is low (priority Indicates a Front Lift system failure (priority level 0). level 1). Indicates an EPB (electric parking brake) failure Generic failure (priority level 0). Indicates an airbag warning light failure (priority Indicates that a check of the Parking Brake system is level 2). required (priority level 0). Indicates a Manettino failure (priority level 1). Indicates a failure in the electronic system Indicates an EBD system failure (priority level 0). (priority level 2). TPMS Indicates that calibration of the TPMS has been Rain sensor failure activated. Indicates a rain sensor failure (priority level 2). Brake pad wear Suspension control system failure Indicates excessive wear of the brake pads (priority Indicates a malfunction in the suspension control level 2). system (priority level 2). Parking sensor failure Contact your Authorized Ferrari Dealer. Indicates that the parking sensor system is faulty (for vehicles equipped with this system) (priority Front Lift system status level 2). When on, it indicates that the Front Lift system is Scheduled Maintenance (Service) activated (vehicle raised). Indicates the Scheduled Maintenance deadline. When flashing, it indicates that the Front Lift system is being operated (activation or deactivation cycle). AVH system Indicates an AVH system failure (priority level 0). 132 About your Vehicle

Ice hazard Electronic tachometer Indicates that the outside temperature is 38 °F The electronic tachometer indicates the engine RPM. The numbers (3 °C) or lower, highlighting the risk of icy road on the dial multiplied by 1000 correspond to the engine RPM in surfaces. one minute. Drive carefully in these conditions and slow down Avoid engine speed rates in the red sector. since tire grip may be significantly reduced. There is a space to the bottom right of the tachometer for the display which gives information on dual clutch transmission (DCT). Warning In this condition, activate the “Low grip” driving Important note mode. In tachometers with white or yellow dial faces, the backlight is not active in daytime conditions (with the running lights off, or Parking brake with the running lights on but daytime light conditions detected Indicates that the parking brake is applied. Gearbox failure by the twilight sensor) to make the instrument panel itself easier to read. 4 Indicates a system failure (priority level 1). Contact your Authorized Ferrari Dealer. Activation of passenger airbag Indicates that the passenger airbag has been activated. Deactivation of passenger airbag Indicates that the passenger airbag has been deactivated. About your Vehicle 133

Engine RPM LED on steering wheel (optional) Gear display The five LEDs on the steering wheel rim (optional) illuminate in The display which gives information on dual clutch transmission sequence and inform the driver that the maximum engine RPM (DCT) is located to the bottom right of the tachometer; with the has been reached for gearshifting. When 5500 RPM is reached, the ignition key in position II, it displays the following information: first LED illuminates; the others illuminate in sequence when 6250, - Gear engaged; 7000, 7750 and 8920 RPM are reached. - Indication of “Auto” gearbox mode; The LEDS on the steering wheel can be deactivated using the - Indication of “Auto easy exit” gearbox mode; MENU screen page on the left TFT display (see page 110): call up the MENU screen page, select the items “Car setup” and “RPM on - Indication of gearbox in “Parking” mode; steer” and then select OFF. To reactivate the function, select ON. - Indication of “Performance Start” mode activated; - Indication of AVH system activated. Important note Information on the gearbox is useful in all operating conditions. 134 About your Vehicle

Gear engaged Indication of “Auto” gearbox mode The gearbox display shows the number or letter indicating the When the gearbox is used in “auto” mode (see page 158), the word engaged gear in the center. “auto” appears in the bottom of the gearbox display together with N Neutral the number or letter indicating the engaged gear. R Reverse Indication of “Auto easy exit” gearbox mode 1 1 gear st When the gearbox is used in “Auto easy exit” mode (see page 158), the word “auto” appears in the bottom of the display together with 2 2 gear nd a small “arrow” pointing downwards on the left. 3 3rd gear Indication of gearbox in “Parking” mode 4 etc. When the gearbox is in “Parking” mode, i.e., the Park Lock gearbox When the key is turned to off, the display remains on for at least locking device is activated (see page 172), the letter “P” appears in 3 seconds and displays the engaged gear. If the control panel reads the center of the gearbox display. N (Neutral), the letter N is displayed and a buzzer will sound. 4 About your Vehicle 135

Indication of “Performance Start” mode activated Right TFT display When the gearbox is used in “manual” mode and the Performance Located on the instrument panel, it performs the following Start function is requested by pressing the appropriate button on functions: the center console (see page 173), “PS” appears in the bottom of the gearbox display and remains while the function is activated. - it displays the speedometer Indication of AVH system activated - it displays infotainment system information In certain circumstances, when the AVH system is activated (see - it displays the rear parking camera (if present). page 171), the word “HOLD” appears in the top of the gearbox display. The driver can interact with the system by selecting the configuration and setting the parameters using the controls on the dashboard to the right of the steering wheel. Holding button A down switches the infotainment system on and off. Holding button B down allows you to select whether to display infotainment system information or display the speedometer. A B 136 About your Vehicle

Infotainment system “Speedometer” screen page The infotainment system includes the following functions: The “Speedometer” screen page indicates the speed by displaying a CD/DVD player with charger mounted in glove compartment, virtual analogue speedometer. AM/FM radio, SAT radio (optional), 30 GB hard disk drive, USB connection, iPod® connector (optional), satellite navigator “Digital speed” screen page (optional), Bluetooth connectivity, voice recognition. The “Digital speed” screen page indicates the speed in digital form. As well as using the commands on the dashboard to the right of the steering wheel, the infotainment system can be controlled using Important note buttons behind the steering wheel. The speedometer is always also displayed in digital form in area For further information on the infotainment system, please refer to D of the left TFT display (speed repetition, see page 109). the instruction manual enclosed with the vehicle documents. Speedometer display Time display The speedometer can be displayed on the right TFT display in “Speedometer” or “Digital speed” mode. By selecting the special item on the MENU screen page of the left TFT display, you can activate/deactivate the time display in the top 4 To select the desired display mode, call up the MENU screen page right of the “Speedometer” and “Digital speed” screen page. The on the left TFT display (see page 110) and select the items “Display time is displayed approximately 10 seconds after key-on. setup”, “Display right”. mph 73 About your Vehicle 137

“Rear Parking Camera” screen page (optional) Cruise Control (optional) If the vehicle has a rear parking camera (optional), the “Rear This is an electronically controlled device which is designed to Parking Camera” screen page is automatically displayed on the right assist you to drive the vehicle at a constant speed from 18.6 mph TFT display when reverse gear is engaged. This screen page, which (30 km/h) to 132 mph (213 km/h) without keeping the accelerator continues to be displayed until reverse gear is disengaged, shows pedal depressed. the field of vision of the camera mounted on the rear bumper and helps the driver when parking. The image is integrated with static green, yellow and red grids that Important note indicate the distance of the obstacles that come into the camera's We recommend using the device on long, dry roads requiring field of vision: the area within the red grid represents the zone from 0 few gear changes (e.g., highways). Do not use the device for city to 24 in. (0 to 60 cm), the yellow grid represents the zone from 24 to driving. 47 in. (60 to 120 cm) and the green grid represents the zone from 47 to 79 in. (120 to 200 cm). Important note PIT SPEED is a motor sports term used by Ferrari to indicate the speed memorized with the device, and does not endorse inappropriate behavior on the road which does not comply with traffic regulations. A OK 138 About your Vehicle

Activating the device Increasing the memorized speed Press and hold down (for more than 0.3 seconds) the control A to This can be done in two ways: by depressing the accelerator and activate the device. memorizing the new speed reached, or rotating the control A When it is activated, the appropriate warning light (see page clockwise (+). 131) illuminates on the instrument panel and a warning light and Each time the control is rotated clockwise, this causes a speed associated message appears on the left TFT display. increase of approximately 1.24 mph (2 km/h) whereas if the control The device can only be activated in 4th or 5th, 6th, 7th gear. When is rotated clockwise and held, the speed increases continuously. driving downhill with the device on, the vehicle speed may increase slightly with respect to the speed memorized. Reducing the memorized speed This can be done in two ways: by deactivating the device and Memorizing the vehicle speed then memorizing the new speed, or by rotating the control A counterclockwise (-) until the new speed that will be automatically Proceed as follows: memorized is reached. - with the device activated, bring the vehicle to the desired speed by pressing the accelerator pedal - rotate the control A clockwise (+) for at least three seconds, Each time the control is turned counterclockwise this will cause a speed decrease of approximately 1.24 mph (2 km/h) whereas if the control is rotated counterclockwise and held, the speed decreases 4 then release it: the vehicle speed will be memorized and you can continuously. release the accelerator pedal If necessary, you can accelerate by depressing the accelerator pedal: Deactivating the device when the pedal is released, the vehicle will return to the speed Press and hold (for more than 0.3 seconds) the control A or turn already memorized. the ignition key to position 0. The device is then automatically deactivated by pressing the brake pedal. Resuming the memorized speed If the device has been turned off by pressing the brake pedal, to Warning resume the memorized speed, proceed as follows: While driving with the device activated, do not put the gearbox - gradually accelerate until the vehicle reaches a speed that in neutral. approaches the speed memorized - quickly press the control A. Warning If the device is malfunctioning or faulty, deactivate the device and contact your Authorized Ferrari Dealer. About your Vehicle 139

Controls on the steering wheel “Manettino” driving mode control switch The driver can select the desired driving mode by using the Start button “Manettino” B. Press the ENGINE START button A to start the engine. When the The driving mode selected does not exempt the driver from engine has started, release the ENGINE START button. complying with the rules of safe driving. Do not hold the ENGINE START button down for a long time. Important note For more information on starting the engine, see page 154. In the event of a failure of one of the onboard systems, signalled by the appropriate symbol on the left TFT display, the system moves to a “recovery” mode, but still allows the vehicle to be driven. In these cases, contact your Authorized Ferrari Dealer. A B 140 About your Vehicle

Driving modes that can be selected with “Manettino” Low-grip mode This is the maximum safety driving mode. Recommended in low grip conditions. SPORT mode This is the ideal setting for vehicle performance recommended for everyday driving. RACE mode This mode offers maximum performance and stability in high grip conditions and is recommended only when using the vehicle on a track. CT OFF mode When this mode is selected, the F1-Trac traction control system is disabled whereas stability control remains active. This setting is 4 used on the racing track. CST OFF mode This mode allows the driver complete freedom and control of the vehicle for track use. No electronic system other than the E-Diff controls vehicle stability. Warning In low- to medium-grip conditions (e.g., wet, icy, sandy roads), do not deactivate the CST system. For further information on the driving modes that can be selected, refer to the paragraph “Driving using the driving mode control switch” on page 164. About your Vehicle 141

Suspension damping button Horn control By pressing button C on the left of the steering wheel, the driver The horn sounds when you press on the horn symbol on the can choose to separate the suspension damping control from the steering wheel rim. logic of the “Manettino” driving mode control switch. For further information, see page 163. C 142 About your Vehicle

“UP” shift paddle Windshield washer/wiper lever Pull the right-hand UP paddle towards the steering wheel to shift gears up. Important note The windshield wipers and washer work only with the ignition “DOWN” shift paddle key in position II. Pull the left-hand DOWN paddle towards the steering wheel to shift gears down. The windshield wipers and washer are operated using lever A on the steering wheel: the lever must be pressed towards the dashboard or pulled back according to the function you require. The windshield wipers have 4 different speeds: OFF Windshield wipers stationary. AUTO The rain sensor adjusts the windshield wiper timing to the 1 intensity of the rain. Slow continuous operation 4 2 Fast continuous operation DOWN UP A About your Vehicle 143

With the wipers stationary (OFF), quickly pressing lever A towards the dashboard activates the windshield wipers in AUTO speed. Important note With the wipers on, quickly pressing the lever towards the Windshield wiper operating is always available even if there is dashboard increases windshield wiper speed (from AUTO to 1, an electronic system failure. If there is a failure, the windshield from 1 to 2). wipers can be activated by pressing lever A and deactivated by With the wipers set to AUTO or OFF, holding the lever towards the pulling it back. dashboard activates maximum speed (2). With speed 1 or 2, on the If there is a particularly serious failure, operating may not be other hand, the windshield wipers stop. automatically maintained: if this is the case, the windshield With the wipers on, quickly pulling lever A back decreases wipers can be kept activated by holding down lever A. windshield wipers speed (from 2 to 1, from 1 to AUTO, from AUTO to OFF). With the wipers stationary, quickly pulling the lever back activates Windshield washer fast temporary operating of the wipers. To activate the windshield washer, keep lever A pulled. When the The windshield wiper speed is indicated in the top of the left TFT lever is released, the windshield wiper returns to the preset speed. display as shown in the figure below. Warning Do not start the windshield washer during the cold months until the windshield has warmed up. If it has not warmed up, the liquid could freeze on the glass and interfere with visibility. A Headlight washer The headlight washer is activated automatically when the windshield washer is operated and the low beams are on. The headlight washer and windshield washer share the same fluid tank and a low fluid level is indicated by the appropriate symbol on the left TFT display. 144 About your Vehicle

Rain sensor Rain sensor failure The rain sensor is designed to automatically adjust the windshield If there is a rain sensor failure, indicated by a special symbol on wiper timing to the intensity of the rain. The system is activated by the left TFT display (see page 132) while the windshield wiper moving the windshield wiper to AUTO. is set to AUTO, the wipers will be set to intermittent operation When operating automatically, the wiper speed ranges from a with one wipe every 1 second approximately. If this is the case, we minimum intermittent setting (one wipe every 5 seconds approx.) recommend that you deactivate the rain sensor and turn on the when the windshield is damp to fast continuous operation in heavy wipers, if necessary, in continuous mode. rain. Important note Important note If the rain sensor should malfunction, contact your Authorized The rain sensor function is deactivated by turning the ignition Ferrari Dealer as soon as possible. key to position 0, also leaving the windshield wiper in position 4 AUTO. To reactivate the system at the next key-on, set the wipers to AUTO by quickly pressing the lever A towards the dashboard. Warning Before cleaning the front windshield (for example in service stations) make sure the rain sensor is deactivated or that the key is in position 0. The rain sensor must also be deactivated when washing the vehicle by hand or in automatic car washes. In case of ice or snow on the front windshield, do not activate the rain sensor to avoid damaging the wiper motor and/or blades. About your Vehicle 145

Lighting system High beams The external lights and turn indicators only work when the ignition To turn on the high beams when the light switch A is set to , key is in position II. pull back lever B on the steering wheel. The external lights can be turned on and off manually or When the high beams are on, the appropriate warning light automatically, depending on the ambient light. illuminates on the instrument panel. Then push lever B towards the dashboard or pull it back to turn off Light switch the high beams and turn on the low beams. The switch A, on the dashboard to the left of the steering wheel, can be set to five different positions: Flashing the headlights 0 Lights off The headlights can be flashed by pushing the left-hand lever B towards the dashboard. Parking and license plate lights on (*) Flashing also occurs with lights off if the ignition key is set to II. Low beams on (*) The high beams are used for flashing. Parking lights AUT Automatic operation of the external lights according to ambient light. (*) The appropriate indicator light on the instrument panel illuminates. B A 146 About your Vehicle

Important note Important note Follow the road regulations of the state or province you are The high beams can only be activated manually by pulling back traveling in for using the high beams. the left-hand lever B. Important note Parking lights The parking lights work only with the ignition key in position 0 or If the high beam control is activated, the high beams will with the key removed. turn on every time the lights are activated automatically. We recommend therefore that you turn them off every time the They are activated by turning the light switch A to position . twilight sensor deactivates the external lights. When the parking lights are on, the warning light illuminates on the instrument panel . When the parking lights are on, hold down one of the two turn indicators C buttons on the steering wheel (see page 130) for Warning If there is fog during the day, the parking lights and low beams 4 more than 0.5 seconds to turn on the partial parking lights on the will not be turned on automatically. The driver must always be corresponding side; press the same turn indicator again for more ready to turn on the lights manually and also the rear fog lights, than 0.5 seconds to go back to full parking lights. if necessary. When the partial parking lights are on (on only one side of the vehicle), the parking light warning light turns off whereas the vehicle symbol indicating which parking light is on (left or right) is Important note displayed on the left TFT display for 10 seconds. After automatic activation of the external lights, it will always When the light switch A is turned to AUT and the ignition key is be possible to turn on the rear fog lights manually. When in position II, the parking lights, low beams and license plate lights the external lights are deactivated automatically, the rear fog turn on and off automatically according to the ambient light. lights are also turned off (if active) automatically. Therefore, if necessary, the driver will have to turn on the rear fog lights manually upon the next automatic activation. About your Vehicle 147

Day lights Warning The LEDS on the headlights serve as front turn indicators and day The driver is always responsible for turning on the external lights. To activate or deactivate the day lights, call up the MENU lights, depending on the ambient light and in compliance with screen page on the left TFT display, select the items “Car setup”, the regulations in force in the state or province of use. The “Day lights” and select ON to activate the function and OFF to automatic system for turning on and off the external lights must deactivate it. be considered an aid for the driver. If necessary, turn the lights on and off manually. Turn indicators Quickly press the left indicator or right indicator button C on the steering wheel to turn on the relevant turn indicator. Twilight sensor The appropriate warning light or will illuminate on the The twilight sensor is comprised of a global sensor which measures instrument panel. the ambient light upwards. The turn indicator goes off when the steering wheel is realigned. In the event of sensor failure, the system switches on low beams Holding down one of the two C buttons (for more than and parking lights, regardless of the daylight conditions; a failure 0.3 seconds) temporarily turns on the relevant turn indicator: it is message will appear on the instrument panel display. turned off after 3 flashes (“lane change” function). The failure indication will be displayed as long as the light switch is turned to AUT. If this occurs, we recommend that you deactivate the automatic system and turn on the external lights manually if necessary. Important note In case of twilight sensor failure, contact your Authorized Ferrari Dealer as soon as possible. C C 148 About your Vehicle

Rear fog lights Hazard warning lights The rear fog lights are turned on only if the high beams or low Press button F to turn on the hazard warning lights. All the turn beams are on when button D is pressed; the appropriate warning indicators will start blinking intermittently; these lights will operate light E will illuminate on the instrument panel to indicate that they with the ignition key in any position. have been turned on. When the hazard lights are on, the appropriate warning light on the instrument panel and on the button flash. Important note To turn them off, press the button again. Use the rear fog lights only in poor visibility conditions. 4 PS A E D F About your Vehicle 149

“Follow me home” function AFS2 adaptive headlights (optional) With the “Follow me home” function, the low beams stay lit for a The AFS2 adaptive headlight system (optional) enables preset period of time once the engine has been turned off and light synchronous movement of the left and right front beams (high and up the area around the vehicle to help the driver and passengers low) and has been designed to illuminate the road better and helps see their way in the dark. reduce areas of shadow in the vehicle's direction. The function can be manually activated by pressing the high The headlights' swivel angle, which ranges from 8° inwards and 15° beam/flashing lever B (see page 146) when the ignition key is in outwards, is defined by the steering angle. position 0 or removed, within 3 minutes of turning off the engine The AFS2 system also uses a “Dynamic Leveling” device that (time that is reduced to 30 seconds if the driver- side door is directs the light beam vertically when accelerating and braking by opened). Each time lever B is pressed, the period of time that the moving the headlights up to 1.9° upwards when braking and up to low beams remain on increases by 30 seconds up to a maximum of 1° downwards when accelerating. 210 seconds. The adaptive headlight system deactivates its corrective action Each time lever B is pressed, the message “Follow me” appears on when driving around corners at low speed. the left TFT display followed by the preset period of time that the low beams remain on. 150 About your Vehicle

Dome light Roof panel controls When the doors are closed, the dome light D on the roof can be turned on or off using the switch E. Door lock/unlock Switches F and G turn the driver-side and passenger-side spotlights Both doors can be locked by activating/deactivating the “LOCK/ on and off. UNLOCK” H button. For further information, see page 96. The dome light activates automatically in the following conditions: - when a door is opened, for approx. 3 minutes Deactivating the anti-lift alarm - when all the doors are closed and the key is in position 0, for Press button L to deactivate the anti-lift alarm system. For further approx. 10 seconds information, see page 21. - when the key is removed, for approx. 10 seconds - when the doors are unlocked, for approx. 10 seconds Front parking sensors (optional) - when the inertia switch is activated, for approx. 15 minutes. On vehicles fitted with front and rear parking sensors, the front The dome light deactivates automatically in the following conditions: - after the preset activation time expires parking sensors are activated/deactivated by pressing button M. When the front parking sensors are activated, the light on the 4 button illuminates. - when the doors are closed and the key is in position II - when the doors are locked - when the inertia switch is reactivated. M F E G H L D About your Vehicle 151

Driving the vehicle Before a trip Preliminary checks Breaking-in period Check the following at regular intervals and always before long The latest manufacturing techniques have allowed us to achieve trips: high precision and accuracy levels in the construction and assembly - tire pressure and condition of components. Nonetheless, the vehicle's moving parts need to be - levels of fluids and lubricants broken in, especially in the first hours of driving the vehicle. - condition of the windshield wiper blades - proper functioning of the warning lights and external lights. Engine and transmission Avoid exceeding 5,000 RPM for the first 620 mi. (1,000 km) . Important note After starting, do not exceed 4,000 RPM until the engine has warmed up (oil temperature: 149-158 °F/65-70 °C). In any case, it is advisable to perform these checks at least every Do not let the engine run at a constantly high speed for a 620 mi. (1,000 km) and always comply with the maintenance prolonged time. schedule. Warning It is also advisable to: - clean the glass covers of the external lights and all the glass BEFORE YOU DRIVE surfaces Check that the seat belts are fastened - properly adjust the mirrors, steering wheel, seats and seat belts. Check that the doors are closed Refilling Check that the seat is properly adjusted Check the rear and side view mirror adjustment Warning Use unleaded fuel only! Using leaded fuel will permanently damage the catalytic converters. For specifications and quantities of lubricants and fluids, refer to the “Recommended lubricants and fluids” table on page 34. 152 About your Vehicle

Starting and driving the vehicle System start-up Important note After turning the ignition key to position II (key-on), both TFT BEFORE YOU DRIVE displays are activated on the instrument panel and system diagnosis If the warning light A does not turn off after diagnosis, is performed. During diagnosis, which lasts 5 seconds, a check is indicating a fault in the gearbox also shown by the symbol and performed on the warning lights on the instrument panel and the special message on the left TFT display (see page 133), contact presence of any faults is checked. your Authorized Ferrari Dealer. If diagnosis detects any errors, they are only displayed once the 5 seconds required for the check have elapsed. The cases listed below are an exception and errors are displayed as soon as the key is turned to on, even during diagnosis: - Low engine oil pressure (see page 129) - Inertia switch triggered (see page 128) - Auto gearbox safety warnings 4 - Deactivation of EPB warning (see page 170). If the next scheduled maintenance deadline is approaching, each time the key is turned to on, information on scheduled maintenance is automatically displayed after diagnosis. For further information, refer to the “Maintenance Schedule” paragraph on page 208. Finally, each time the key is turned to on, the message for activation of the alarm when an intrusion has been attempted (see page 21) is also displayed (after diagnosis). Once the system check has been completed, the gearbox display is activated and the letter “P” (Parking) or “N” (Neutral) will be displayed. A A About your Vehicle 153

Starting the engine Important note Before starting the engine, make sure that the alarm system and all The vehicle is equipped with an electro-hydraulically controlled electrical devices with high power absorption are turned off. gearbox system operated by means of paddles on the steering • Make sure that the electric parking brake is applied and that the wheel. doors are closed. The default setting for the DCT gearbox is always “Auto easy • Hold the brake pedal down when starting the engine. exit” mode (see page 158). Every time the vehicle is started, the DCT gearbox is in “Auto Warning easy exit” mode (see page 158) unless the vehicle was in “Auto” mode when the engine was turned off. Do not press the accelerator pedal. To exit the “Auto easy exit” mode operate the UP and DOWN paddles (while the vehicle is moving) or press the AUTO button • Turn the ignition key to position II and wait for the gearbox display to come on. on the center console. • Press the ENGINE START button (see page 140) and release it as soon as the engine starts. Important note Do not hold the ENGINE START button down for a long time. Immediately release the UP and DOWN paddles or button R If the engine does not start, turn the key back to position 0 and after the gearbox display shows that the gear has been engaged; wait for the gear display to go off before retrying. a prolonged maneuver will cause the gearbox failure warning light to turn on (see page 133) and triggering of the buzzer. Warning Hold the brake pedal down while starting the engine. Important note None of the gears can be engaged if the luggage compartment lid is open or not properly closed. When the vehicle is stationary, with the driver-side door open or not properly closed and the brake pedal released, the system disengages the gear engaged after approximately two seconds. 154 About your Vehicle

If the engine fails to start after several attempts, check for one of the following causes: Warning • insufficient speed of the starter motor (dead battery) If the UP and DOWN paddles are not working, the message • ignition device faulty “Depress brake pedal and press PS to engage gear” will appear • electrical contacts faulty on the left TFT display; you can therefore engage the gear by pressing the PS button on the center console (see page 173) and • fuel pump fuses blown. the brake pedal. Warming up the engine In these cases, the “Performance Start” function is not available. If the engaged gear was R, the PS button must be pressed twice Do not run the engine at high speed until the engine oil temperature to engage 1st gear. has reached at least 65-70 °C (149-158 °F), approximately. Driving the vehicle Important note With the engine started, the vehicle stationary and the brake pedal pressed, pull the right-hand UP paddle towards the steering wheel to engage 1st gear. When reverse is selected, an acoustic safety signal beeps intermittently as long as “R” is engaged. 4 Release the brake pedal and press the accelerator to start off. With the engine running and the vehicle stationary, you can change If the system automatically selects 2nd gear when attempting to directly from 1st or 2nd gear to “R” (reverse) by pressing R on the shift from “R” to 1st gear, this indicates that 1st gear has jammed. center console and from reverse to 1st by moving the UP paddle. Therefore, this is not a malfunction, as it falls within the system operating logic. For the same reason, when shifting from 1st gear to “R”, the system will automatically engage “N” if the gear has jammed. During prolonged stops with the engine running, it is advisable to keep the gearshift in “N”. R Important note If you allow the vehicle to move forward in N, when UP or DOWN is requested, a gear will be engaged that corresponds to the speed of the vehicle. About your Vehicle 155

UP-shifting DOWN-shifting Use the right-hand UP paddle without releasing the accelerator Use the left-hand DOWN paddle without releasing the accelerator pedal. pedal. An UP-shift request is not accepted when engagement of the A DOWN-shift request is not accepted if engagement of the requested gear forces the engine to underrev or if an UP-shift is requested gear forces the engine beyond a certain RPM, depending already in progress because of engine overrevving. on the gear requested, or if a DOWN-shift is already in progress In any event, it is advisable to: because of engine underrevving. • Shift gears without releasing the accelerator pedal if pressed. In any event, it is advisable to: • Wait until gearshifting has been completed before requesting the • Shift gears without releasing the accelerator pedal if pressed. next shift, avoiding a rapid sequence of multiple requests. • If DOWN-shifting is requested to start overtaking which requires quick acceleration, press the accelerator pedal just before using UP-shifting due to overrevving the paddle. The system is designed to “automatically” engage a higher gear if the • Wait until gearshifting has been completed before requesting the accelerator pedal is pressed and the engine approaches the maximum next shift, avoiding a rapid sequence of multiple requests. RPM (overrevving). DOWN-shifting due to underrevving Important note • The system shifts down “automatically” if the engine goes below a This will not occur when the system is in “RACE”, “CT OFF” and minimum number of revs (1250 RPM). “CST OFF” driving mode. • The DOWN-shift request from the paddle is ignored if gearshifting is already in progress due to engine underrevving. Sequential downshifting During deceleration, with the brake pedal pressed and the ABS system not activated, sequential downshifting can be performed by holding the left-hand “DOWN” paddle down. The sequential gearshifting request is accepted until the second gear is engaged. This system is only activated when the “Manettino” is set to SPORT, RACE, CT OFF or CST OFF. 156 About your Vehicle

“N” (Neutral) request With the engine running, pull both UP and DOWN paddles towards Warning the steering wheel at the same time without pressing the brake pedal Never leave the vehicle with the gearbox in “N”. Always make sure to request neutral “N”. that the letter “P” (Parking) appears on the gearbox display. If necessary, “N” can be requested at any speed. Subsequently, if an “UP” or “DOWN” shift is requested, the system will engage the gear most suited to the speed of the vehicle. Warning Stopping the vehicle Never leave the vehicle with the engine running. When the vehicle stops, the system automatically engages 1st gear unless Neutral has already been requested. Important note When the vehicle is stationary and the engine is running, hold the brake pedal down until ready to move off again. If the vehicle is not in Parking mode (the letter “P” must be Turning off the engine displayed on the gearbox display), the key cannot be removed. 4 The engine can be turned off with the gearbox either in “N” or For information on the Park Lock, see page 172. with a gear engaged. After turning the ignition key from position II to position 0, the gearbox display will remain on for a few more seconds to display the engaged gear. If the gearbox is in “N” a buzzer will sound. Before turning off, the letter “P” is displayed on the gearbox display to inform the driver that the Park Lock has been activated. About your Vehicle 157

“Auto” gearbox mode “Auto easy exit” gearbox mode The “Auto” gearbox mode is enabled/disabled by pressing the Every time the vehicle is started, the gearbox starts in “Auto easy AUTO C button on the center console. When the “Auto” mode is exit” mode unless it was in “Auto” mode when the engine was enabled, the word “auto” appears on the gearbox display. To exit turned off. In this case, it remains in “Auto” mode the next time the the “Auto” mode, you must press the AUTO button until the word engine is started. “auto” on the gearbox display disappears. Activation is signalled by the word “auto” and an arrow in the When the “Auto” gearbox mode is enabled, the system will gearbox display. automatically UP-shift and DOWN-shift according to vehicle speed, In this mode, the system will automatically UP-shift and DOWN- engine rpm and the torque/power request of the driver. shift according to vehicle speed, engine rpm and the torque/power When you are in “Auto” mode, you can however manually shift request of the driver. gears using the UP and DOWN paddles. The system remains in To exit the “Auto easy exit” mode and go to “Manual” mode, “Auto” mode: this is indicated by the word “auto” flashing on the operate the UP or DOWN paddle (while the vehicle is moving) or gearbox display when the paddles are used. press the AUTO button on the center console. When the vehicle is stationary, a “N”, 1st gear or “R” request will not If the “Auto” gearbox mode is then requested by pressing the result in a change from “Auto” to “Manual”. AUTO button, the system will apply all the characteristics of the “Auto” gearbox mode. Push start Warning C Starting the vehicle by the means of push starting is not possible. 158 About your Vehicle

Proper driving While traveling It is essential that the driver be aware of the best driving - Caution is the number one rule for safe driving, which also means techniques suited to various circumstances. Always try to prevent you should take other people’s behavior into consideration. dangerous situations by driving with caution. - Follow the road regulations in force in the state or province you Before you drive are driving in and always respect the speed limit. - Adjust the position of the seat, steering wheel and the rear and - Always make sure that the driver and passengers have their seat side view mirrors, in order to obtain the best driving position. belts fastened and that all children are traveling in suitable child - Adjust the backrest so that your chest is upright and your head is seats. as close to the headrest as possible. - Good personal physical conditions help ensure you can drive long - Properly fasten the seat belts distances safely. - Ensure that nothing (e.g., mat covers, etc.) is blocking the pedals. - Check that all lights including the headlights are working Warning properly. - Ensure that any child restraint systems (e.g., child seats, etc.) are Driving under the influence of drugs, alcohol, or certain medications is dangerous to yourself and others. 4 properly fixed on the passenger seat. Traveling without your seat belt fastened increases the risk - Your reflexes are quicker if you eat lightly before driving: avoid of serious injury and death in the event of a collision. Always heavy meals before a trip. fasten seat belts and use child seats, if necessary. - Never drink any alcoholic beverages before and during the Do not travel with objects lying on the floor, especially in front journey. of the driver’s seat: in the event of braking, these could slide At regular intervals, check the following: under the pedals, making it impossible to brake or accelerate. - Tire pressure and condition. Additionally, ensure that the floor mats fit correctly. - Engine oil level. Water, ice and salt spread on icy roads may deposit on the brake discs and reduce the efficiency of the initial braking. - Engine coolant level and system condition. - Brake fluid level. - Steering fluid level. - Windshield washer fluid level. About your Vehicle 159

- Make regular stops to loosen up your limbs and refresh yourself, Driving in the rain and avoid driving for hours on end. Rain and wet roads can cause hazardous situations. - Keep a constant air circulation in the passenger compartment. All maneuvers are more difficult on a wet road since tires have - Never coast downhill with the engine off: in these conditions significantly less grip on the road. This means that the braking the engine brake, servo brake and power steering are inefficient, distances increase considerably and road-holding decreases. braking requires greater pressure on the pedal and steering will Below is some advice for driving in the rain: be harder. - Keep a greater safety distance between yourself and the other Driving at night vehicles and reduce your speed. When you are traveling at night, follow these fundamental rules: - When it is raining very hard, visibility is also reduced. In these - Reduce speed, particularly on dark roads. cases, to make yourself more visible to others, turn on the low - Driving conditions are more demanding at night, so take beams even during the day. particular care. - Drive through puddles at low speed to avoid losing control of the - If you start feeling tired or sleepy, stop immediately: to continue vehicle (“aquaplaning”): if this occurs, grip the steering wheel driving would be a risk for yourself and for others. Continue only firmly. after you have had a rest. - The recommended driving mode when driving in the rain is - At night, it is difficult to judge the speed of vehicles in front of "Low Grip" mode. you as you can only see their taillights: keep at a greater safety distance than you would during the day. Warning - Use the high beams only outside of urban areas and when you are If the road is wet, reduce your speed to avoid “aquaplaning”, sure that they will not disturb other drivers. during which the tire no longer touches the road surface. - Turn off the high beams when you see oncoming vehicles and use This is due to the fact that, when the road is very wet and the the low beams. vehicle speed is high, the side channels of the tire tread are - Keep the lights and headlights clean. not capable of removing all the channelled water due to their - Watch out for animals crossing the road when traveling outside particular shape or insufficient depth and a layer of water is urban areas. placed between the road surface and the tire. The fluid pressure generated is so high that it supports the vehicle's weight making it virtually impossible for the driver to control the vehicle. 160 About your Vehicle

- Use the ventilation system to demist the windshield (see Driving on mountain roads page 185) and avoid visibility problems. Below is some advice for driving on steep mountain roads: - Periodically check the condition of the windshield wiper blades. - To prevent the brakes from overheating when driving downhill, Driving in fog use the engine to brake by engaging a lower gear. Whenever possible, avoid driving if there is thick fog. If you have - Never coast downhill or drive downhill with the engine off or to drive in misty conditions, or if there is thick fog or fog banks, in neutral, nor with the ignition key removed from the steering follow these rules: column. - Keep a moderate speed. - Drive at a moderate speeds and do not “cut” corners. - Turn on the low beams, also during the day, and use the rear fog - Remember that overtaking uphill is slower and requires a longer light. Avoid using the high beams. free stretch of road. If you are overtaken when driving uphill, ensure that the other vehicle can pass easily. Driving on snowy or icy roads Warning On roads where visibility is good, turn off the rear fog light, it may be annoying for the occupants of the vehicles behind you. Below is some advice for driving in these conditions: - Keep a very moderate speed. 4 - Keep a safe distance from the vehicles in front of you. - Remember that fog makes the road damp and therefore all - Fit snow tires approved for the vehicle. maneuvers are more difficult and braking distances are longer. - Given the poor grip, use the engine brake as much as possible - Keep a safe distance from the vehicle in front of you. and avoid sudden braking. - As far as possible, avoid suddenly changing speed and direction. - Avoid sudden acceleration and sharp changes in direction. - As far as possible, avoid overtaking. - During the winter season, even apparently dry roads can have icy sections. - In the event of an emergency stop, (e.g., failures, inability to proceed due to poor visibility conditions, etc.) try to leave the - Be careful when driving along stretches of road in the shade as main driving lane. Then turn on the hazard warning lights and, if there may be icy patches. possible, the low beams. On approaching another vehicle, sound the horn rhythmically. About your Vehicle 161

Driving with the “ABS” braking system The ABS system assists the driver as follows: - It is designed to help prevent the wheels from locking and skidding during emergency braking, particularly in low-grip conditions. - It allows braking and changing direction at the same time. This feature is affected by the physical limits and lateral grip of the tires. - When the ABS is activated, you will feel a slight pulsing of the brake pedal during emergency braking or in low-grip conditions. This is normal. DO NOT release the pedal but continue to depress it to give continuity to the braking action. - The ABS helps prevent the wheels from locking, but it does not increase the physical limits of grip between the tires and the road: keep a safe distance from the vehicles ahead and reduce speed before curves. 162 About your Vehicle

Suspension damping control Level 1 (COMFORT) This vehicle uses latest generation MagneRide™ magnetorheological Slightly more flexible setting, optimized to better absorb road suspension, a system developed by Delphi and refined by Ferrari unevenness and provide a better grip on wet road surfaces for continuous automatic damping control. (Manettino set to “Low grip”). By processing data received from the vehicle dynamics sensors and Level 2 (SPORT) sensors that detect bodyshell movements, the ECU interprets the Slightly more rigid adjustment optimized for sports-style driving driving conditions and the road surface and immediately adjusts and for high speed (with medium-high grip), without significantly suspension response by varying the control current of each shock affecting comfort (Manettino set to “SPORT”). absorber. Level 3 (RACE) These sensors allow the ECU to calculate the vehicle speed, vertical Even more rigid setting optimized for use on the race track and lateral acceleration, steering angle and instantaneous pressure (Manettino set to RACE, CT OFF, CST OFF). in the braking system, and hence to control suspension damping. 4 This system not only ensures an optimal compromise between racing-style performance (handling) and comfort, but is capable of emphasising either aspect by using the different adjustments available controlled by the “Manettino” driving mode control switch. Three different setting levels are available on this vehicle. About your Vehicle 163

Driving using the driving mode control switch SPORT mode (“Manettino”) The “SPORT” mode is the best setting for daily road use. This mode is designed to ensure stability only in medium-high grip The driving mode control switch on the steering wheel is designed conditions. Suspension damping shifts to Level 2 and gearshifting to allow the driver to use the vehicle potential in a fast and intuitive is more rapid. The CST system also switches to a different level way. offering you greater driving freedom. There are five modes available, which correspond to the grip If “SPORT” mode is selected, it is indicated on the left TFT display level (from low to high) and consequently to the level of driving as shown below: assistance required (from high to none). Low-grip mode “Low-Grip” mode provides stability on dry as well as on wet roads. It is therefore recommended for low grip conditions (e.g., rain) and on slippery or extremely uneven roads, but also to enhance comfort during city driving. Suspension damping is optimized to provide the best possible absorption (Level 1) and the CST system is at its maximum level; the standard Bosch ASR system is activated instead of the F1-Trac function. If “Low grip” mode is selected, it is indicated on the left TFT display as shown below: 164 About your Vehicle

RACE mode The RACE mode is to be used exclusively on the race track. Warning Gearshifting favors the racing style of the vehicle whereas the CST Use of the vehicle on race tracks: after each start, cover the first shifts to Level 3 (engine power reductions are minimal) and the straight stretch of the track (at least 0.3 mi/500 meters) at a suspension becomes even stiffer (Level 3). The performance ABS constant speed so that the traction control system and the ABS shifts to “Sport” level. This mode is designed to ensure stability on may calculate exactly the grip available and the diameter of the the race track in high grip conditions. tires (the calculation is reset every time the engine stops). If “RACE” mode is selected, this is indicated on the left TFT If this rule is not followed, system performance may be reduced. display as shown below: 4 About your Vehicle 165

CT OFF mode CST OFF mode In “CT OFF” mode the F1-Trac traction control is disabled. This In “CST OFF” mode the CST system is disabled. No electronic mode further enhances the already racing -style behavior of the systems other than the E-Diff control vehicle stability and the vehicle: traction control is disabled while stability control remains driver is allowed complete freedom and control of the vehicle active when a certain level of sideslip is exceeded. The gearshift for track use. The gearshift mode, suspension damping and the mode, suspension damping and the performance ABS setting are performance ABS setting are the same as the “RACE” and “CT the same as the previous position. The electronic differential has a OFF” modes. specific setting developed to emphasise the dynamic qualities of the vehicle. Stability is not ensured. Warning If “CT OFF” mode is selected, this is indicated on the left TFT display as shown below: In low- to medium-grip conditions (e.g., wet, icy, sandy roads), do not deactivate the CST system. Important note Every time the engine is started, the CST system will reactivate. Important note When the brake pedal is pressed, traction control is activated via the VDC system (vehicle dynamics control via the braking system). 166 About your Vehicle

If “CST OFF” mode is selected, this is indicated on the left TFT display as shown below: 4 About your Vehicle 167

Suspension damping button If button A has been pressed and subsequently the position of the Manettino is changed, the suspension setting follows the operating The driver may decide to separate the suspension setting from the logic dictated by the Manettino. logic of the “Manettino” driving mode control switch using the button A on the steering wheel. Important note By pressing button A, irrespective of the position of the Manettino, the suspension setting shifts to Level 1 (COMFORT). Upon turning off and restarting the vehicle, the suspension setting depends on the position of the Manettino. Position of Suspension Button A pressed Manettino setting When the Manettino is set to SPORT, RACE, CT OFF or CST OFF, Low grip COMFORT remains COMFORT shifting to the COMFORT suspension setting by pressing button SPORT SPORT shifts to COMFORT A is indicated by displaying the special symbol and “Bumpy road” message on the left TFT display for 5 seconds. RACE RACE shifts to COMFORT CT OFF RACE shifts to COMFORT CST OFF RACE shifts to COMFORT A Bumpy road 168 About your Vehicle

After 5 seconds, next to the Manettino status in the top of the display, the suspension symbol continues to be displayed as shown in the photo below (example shows Manettino in “SPORT” mode). 4 About your Vehicle 169

EPB - Electric parking brake Warning On this vehicle the parking brake is actuated by an electric motor. The parking brake can be applied and released using the special Always apply the parking brake when the vehicle is parked. control B on the dashboard to the left of the steering wheel. If the parking brake should fail to function, contact your A warning light illuminates on the instrument panel to indicate that Authorized Ferrari Dealer. the parking brake has been applied (see page 133). It is deactivated by pushing down the brake pedal and pressing Deactivation of EPB warning button B. The warning light will go off when the parking brake has been released completely. If the electric parking brake is activated, the message “Depress brake pedal and deactivate EPB”, is immediately displayed on the The electric parking brake can be used as an emergency brake left TFT display (even during system diagnosis, see page 153) when the vehicle is in motion. If this is the case, the system acts on accompanied by an acoustic signal when the vehicle is started. all four wheels until button B is released by communicating with the ESP system which prevents locking. With the engine running and the parking brake still activated, once a speed of 6 mph (10 km/h) is reached, the message “Parking brake on”, is displayed on the left TFT display accompanied by an acoustic signal. B 170 About your Vehicle

Autopark function The EPB Autopark function automatically activates the electric parking brake when the engine is turned off. When the key is turned to on, the Autopark function is always activated but can be temporarily deactivated by pressing the AUTO PARK C button. When the C button is pressed, the message “PARK OFF” is displayed on the left TFT display for 5 seconds. If button C is pressed again, then the message “PARK ON” is displayed on the left TFT display for 5 seconds. “Automatic Vehicle Holding” AVH function The electric parking brake provides optimized release on hill starts due to its Automatic Vehicle Holding function: in certain circumstances, this system keeps the vehicle stationary using differentiated brake shoe/pad release so that there is time to move 4 your foot from the brake pedal to the accelerator without the vehicle moving backwards. C About your Vehicle 171

Park Lock Carwash procedure The Park Lock is a locking device built into the gearbox. The Park lock device can be electrically disabled on a temporary This device is used to help prevent the vehicle from moving when basis when the engine is turned off by performing the Carwash the multi-disc clutches are open, i.e., with the engine off and/or procedure. without the hydraulic pressure required for gearbox operation. This procedure is necessary when the vehicle has to be moved with The device operates automatically every time the key is turned to the engine off. off: if a gear is engaged when the key is turned to off, the Park Lock is immediately activated. If the gearbox is in “N” (neutral), the Warning Park Lock starts operating after a minimum preset time (needed for the Carwash procedure, see next paragraph). To inform the driver When the Park Lock device is electronically deactivated that the Park Lock has been engaged, the letter “P” is displayed on (Carwash procedure), the vehicle may move. the gearbox display. The vehicle is only kept stationary by the parking brake which must be applied. The Park Lock is deactivated when the engine is running, the first gear or “R” is requested (with the brake pedal pressed) and the luggage compartment lid has been closed correctly. To perform the Carwash procedure, do the following: - with the engine running, select the first gear; - select neutral “N”; - switch off the engine; - turn the key to position II (key-on) within 3 seconds of turning off. The message “Carwash mode activation” will appear on the left TFT display. 172 About your Vehicle

Performance Start Warning The “Performance Start” function helps provide the vehicle with a sportier acceleration. We strongly advise you that Performance Start only be used in a The device, which is not available when the Manettino is set to controlled environment (e.g., on a race track). the “Low grip” driving mode, transfers the necessary torque to the ground and avoids skidding of the wheels during acceleration. Important note To start the vehicle in “Performance Start” mode, do the following: The “Performance Start” function is not available in presence of: - the vehicle must be stationary - a sloping road surface, even slight - the gearbox must be in “Manual” mode - high clutch temperatures - hold the brake pedal down and select first gear - press the PS P button on the left of the center console: an acoustic signal informs the driver that the device has been activated and “PS” appears on the gearbox display - press the accelerator pedal and release the brake pedal. 4 P About your Vehicle 173

“Front Lift” system (optional) Throughout the entire Front Lift system activation cycle, the warning light (see page 132) flashes and the vehicle symbol with On request, the vehicle can be fitted with a front suspension lift an arrow pointing upwards and a message “Front Lift moving” system: this device acts on the front suspension and raises the appears on the left TFT display. When the system has been front of the car by approximately 1.5 in. (40 mm) to make access to activated (front of the vehicle raised), an acoustic signal is emitted garages or steep ramps easier and avoid damaging the car. and the message “Front Lift ON” appears for 5 seconds whereas The system can be activated when the engine is running at a the warning light on the instrument panel stays on until the system speed of below 25 mph (40 km/h) by pressing button A on the is deactivated. center console. At speeds of over 25 mph (40 km/h), the system To deactivate the system, press button A again: at the start of is deactivated whereas if it is already activated, it is automatically the deactivation cycle, the warning light on the instrument panel deactivated when exceeding 25 mph (40 km/h). starts to flash again and the vehicle symbol with an arrow pointing downwards and the message “Front Lift moving” appears on the left TFT display. The message remains until the system has been completely deactivated. Front Lift moving A 174 About your Vehicle

If the engine is turned off with the front suspension lift activated, In the event of engine failure, the “Front Lift” system can however the message “Front Lift ON. Set Front Lift to OFF” appears on the be activated by pressing button A for 10 seconds. In this way, the left TFT display at key-off. Turn the key back to position II (key- vehicle front can be lifted even in emergencies when the engine is on) and press button A to lower the vehicle. If it is not manually turned off (for example, to load it onto the ramp of a flatbed truck). deactivated by pressing the button, within 15 seconds of turning off the engine, the system is automatically deactivated. Important note The front suspension lift should only be used for the purposes Warning described above and not to drive over speed control systems The system has not been designed to remain activated when (e.g., speed bumps) more quickly. the engine is turned off and the vehicle is stationary. If the engine is turned off with the front lift activated, the vehicle is automatically lowered after 15 seconds. Do not use the front suspension lift to park the vehicle on obstacles (e.g., pavements); these obstacles may come into contact with the front of the vehicle and damage it once the 4 system has been deactivated. Front Lift ON About your Vehicle 175

Seat adjustment Backward/forward adjustment Pull lever B up and slide the seat forward or backward to the desired position. Release the lever and slightly move in the seat to Warning check that it is locked in place. As with all adjustments, seat adjustments must be performed when the vehicle is stationary. Warning Correct adjustment is very important for enhanced driving comfort The backward/forward adjustment must consider the fact and maximum efficiency of the passive safety systems. that airbag devices are placed in front of the driver and the passenger (see page 71). Basic seat Correct adjustment ensures there is adequate space between the The seat position can be adjusted using the special controls. airbag and the driver/passenger (see page 71). Seat back rake adjustment Turn knob C clockwise or counterclockwise until it reaches the desired position. B C 176 About your Vehicle

Tilting the backrest To tilt the seat, pull lever L up and push the backrest towards the front of the vehicle. When the backrest goes back into position, it will automatically lock once it has reached the correct position. 4 L About your Vehicle 177

Electrically-adjustable seat (optional) Seat back rake adjustment The seat position can be electrically adjusted using the special Use control E to adjust the seat back rake. Push the control forward controls. or backward to adjust the seat back rake. Three adjustments are possible using control D: Lumbar support adjustment (Full Electric option) - backward/forward adjustment: push the control forwards or Use control F to pneumatically adjust the lumbar support. Use the backwards control to increase or decrease the lumbar support. - height adjustment: push the control up or down - seat inclination (tilting): push the front or rear end of the control Backrest and cushion side width adjustment (Full Electric option) up or down to adjust seat inclination. Use control G to pneumatically adjust the width of the backrest sides and the seat cushion. Use the control to increase or decrease Warning the side width. The backward/forward adjustment must consider the fact that airbag devices are located in front of the driver and the passenger (see page 71). Correct adjustment helps ensure that there is adequate space between the airbag and the driver/passenger (see page 71). D E 178 About your Vehicle

Driver’s seat position memory (Full Electric option) With reverse gear engaged, the position of the passenger side view When a door is open and the key is in position 0, the seat can be mirror can be adjusted to a position other than the driving position, moved for a limited period (approx. 15 sec.). Each time a door is to help parking maneuvers. This position can be memorized along opened or both doors are closed and the key is set to OFF, the seat with all the other memorized positions. can be moved again for a limited period. If the personalized reverse gear mirror position is never set, when The seat position can only be memorized when the key is in the reverse gear is engaged, the passenger side view mirror will in position II, by pressing one of the three buttons 1, 2 or 3 (H) any case move slightly downwards and inwards (compared with the each one corresponding to a memorized position. Pressing one of driving position). these buttons for longer than 3 seconds memorizes the position of the driver seat, rear and side view mirrors and steering wheel (confirmed by a double tone). To recall the memorized position, press one of the buttons H and release it within 3 seconds. Operation begins as soon as the button is released. Recalling the memorized position is not allowed when the vehicle 4 is in motion. If the vehicle starts to move while the memory recall is being operated, the seat and column do not stop moving until reaching the memorized position. � � � About your Vehicle 179

Seat heating system (Full Electric option) Tilting the backrest Turn control N to activate the seat heating function. To tilt the seat, pull lever L up and push the backrest towards the When this function is active on one or both seats, the appropriate front of the vehicle. warning light on the instrument panel illuminates. Using control N, When the backrest goes back into position, it will automatically lock the driver can adjust the heating, choosing from 3 levels identified once it has reached the correct position. on the control with the numbers 1, 2 and 3. In position 0, seat heating is not activated. Warning Do not use the electric seat adjustment controls when the backrest is tilted. � L 180 About your Vehicle

Racing seat Seat back rake adjustment The seat position can be adjusted using the special controls. Turn knob Q clockwise or counterclockwise until the desired back rake has been reached. Backward/forward adjustment Tilting the backrest Pull lever P up and slide the seat forward or backward to the desired position. Release the lever and slightly move in the seat to Pull lever R up to tilt the backrest forward. check that it is locked in place. Warning The backward/forward adjustment must consider the fact that airbag devices are located in front of the driver and the passenger (see page 71). Correct adjustment helps ensure that there is adequate space between the airbag and the driver/passenger (see page 71). 4 Q R P About your Vehicle 181

Adjusting the steering wheel Rear and side view mirrors The steering wheel can be electrically adjusted for rake and reach. Internal rear view mirror It can only be adjusted if the ignition key is in position II. Move control A (to the left of the steering column) in the four Hold the internal rear view mirror and move it to the required directions to adjust the steering wheel. position. On vehicles equipped with a driver's seat with memory, the position On request, the internal rear view mirror can be fitted with an of the steering wheel is memorized together with the position of optional electrochromic mirror that automatically darkens to reduce the side view mirrors when the seat position is memorized. the glare effect of the reflected light on the driver. The speed with which the mirror darkens depends on the intensity of the light. By pressing button B you can activate/deactivate the electrochromic Warning mode. When the electrochromic mode is activated, the green LED Do not adjust the steering wheel when the vehicle is moving. D illuminates. D A B 182 About your Vehicle

Side view mirrors On vehicles equipped with a driver's seat with memory, every time These mirrors can be electrically adjusted using the control C (with the seat position is memorized, the side view mirror position is also the ignition key in position II) and are equipped with defogging stored automatically, both for the normal traveling direction and elements. reverse maneuvering. 1) Mirror selection: turn control C to the left or right lock position To memorize a new position of the side view mirrors, turn the to select the mirror that requires adjusting. ignition key to position II and adjust the position of the mirrors; then engage reverse and reposition the side view mirrors to ensure 2) Mirror positioning: move control C in the four directions the best possible visibility to perform the maneuver, then disengage (up – down – right – left) to adjust the selected mirror. reverse gear. 3) Mirror closure (optional): turn control C to the lower central Finally, press one of the buttons 1, 2 or 3 on the seat (see lock position to close the side view mirrors. page 179), each one corresponding to a memorizable position, until Once adjusted, rotate the control C into the upper central position a double tone confirms that the procedure is complete. where it will be locked in order to avoid changing the external The new position of the side view mirrors will be automatically mirror setting inadvertently. The mirrors will fold in both directions in the event of a collision: if necessary, the mirrors can be pushed both backwards and forwards. memorized together with the seat position. In addition, the mirror positions can be adjusted for both the 4 normal traveling direction and for reverse manoeuvring. Warning The rear and side view mirrors must always be positioned correctly while driving. Do not adjust the rear and side view mirrors when the vehicle is moving. On request, the side view mirrors can be fitted with an electrochromic mirror. C C About your Vehicle 183

Air conditioning and heating system Controls 1 Left-hand temperature setting and AUTO button Operating modes 2 A.C. compressor activation/deactivation Automatic 3 Single-zone mode activation/deactivation This mode automatically adjusts the air distribution, temperature 4 Air distribution fan speed and ventilation levels according to the temperature set by the user. 5 Rear window demist activation/deactivation Partially Automatic 6 Windshield demist activation/deactivation This mode allows the user to adjust certain parameters manually, 7 Right-hand temperature setting and AUTO button while others remain automatic. 8 Right-hand air distribution mode setting Manual 9 Air recirculation This mode allows the user to set the values to suit the passenger's 10 Left-hand air distribution mode setting needs. 1 2 3 4 5 6 7 10 9 8 184 About your Vehicle

Left-hand temperature setting and AUTO button (1) Air distribution fan speed (4) This is used to select the required air temperature in the left-hand The four setting positions allow the occupants to select the air flow side of the passenger compartment; the AUTO button is used to rate. activate automatic operation (LED on). Rear window demist activation/deactivation (5) A.C. compressor activation/deactivation (2) Press this button (LED on) to activate rear window defogging/ This is used to activate (LED on) or deactivate (LED off) the A.C. demisting. compressor. Windshield demist activation/deactivation (6) Single-zone mode activation/deactivation (3) Press this button (LED on) to activate windshield defogging/ This is used to activate (LED on) or deactivate (LED off) the demisting. single-zone operating mode. 4 1 2 3 4 5 6 About your Vehicle 185

Right-hand temperature setting and AUTO button (7) Air recirculation (9) This is used to select the required air temperature in the right-hand If released (LED off), the air flow comes from outside the side of the passenger compartment; the AUTO button is used to passenger compartment. activate automatic operation (LED on). When outside temperatures exceed 90 °F (32 °C), the air Right-hand air distribution mode setting (8) recirculation feature remains on with a 60-second pause every This is used to select one of the six air flow distribution modes in twenty minutes to refresh the air. the right-hand side of the passenger compartment. If you activate the windshield washer function, the air recirculation feature activates for 20 seconds, to prevent any smell of windshield washer fluid from entering the passenger compartment. If pressed (LED on), the air flow comes from inside the passenger compartment. The recirculation increases air heating or cooling. Left-hand air distribution mode setting (10) This is used to select one of the six air flow distribution modes in the left-hand side of the passenger compartment. Once the internal temperature has stabilized at the desired level, you are advised not to change the position of the temperature selection switch unless the external temperature changes drastically. 7 8 10 9 186 About your Vehicle

Maintenance The pollen filter must be replaced every year, as indicated in the Important note “Maintenance Schedule”. We recommend keeping the air flow set to open and directing the air flow to a neutral position. Important note The air coming out of the vents does not correspond to the temperature requested by the user, but is the temperature required to maintain the desired temperature inside the passenger compartment. Adjusting the air vents The adjustable air vents are positioned on the sides and in the central section of the dashboard. Use control A to direct the air flow. 4 Use control B to adjust the air flow rate. Turned to left: closed. Turned to right: open. A B About your Vehicle 187

Passenger compartment accessories Opening of the glove compartment can be deactivated by pressing button C. Call up the MENU screen page on the left TFT display Glove compartment (see page 110) and then select the items “Car setup”, “Glove box The glove compartment is located on the passenger side of the key” and OFF. To reactivate opening using the button, select ON. dashboard. To open it press the OPEN C button on the center console: the glove compartment will move down slowly by way of a damped opening mechanism. The glove compartment is illuminated by an internal light that comes on automatically when it is opened. Warning Keep the glove compartment closed while driving. To close the glove compartment, push the top part until you hear the click of the lock. C 188 About your Vehicle

Pocket-change compartments Sun visors They are located on the lower part of the doors and on the center The sun visors can be moved by pulling them down towards the console. windshield and sideways by unhooking them from the fastener and There is also a cup holder in the front of the center console. turning them towards the door glass. 4 About your Vehicle 189

12V power socket The power socket D on the center console can be used to power small electrical devices such as mobile phones, lights, vacuum cleaner and any other accessory with absorption not exceeding 140 watts and a voltage of no more than 12 volts. Warning Prolonged use of a small electrical device may discharge the battery. Do not try to insert plugs into the power socket that are not the right size and shape. Warning Use the power socket to connect the tire repair and inflation kit in an emergency ONLY for the amount of time strictly necessary. D 190 About your Vehicle

Toolkit ................................................................ 194 Replacing light bulbs ........................................... 199 Replacing a fuse .................................................. 202 Replacing a wheel ................................................ 210 Towing ................................................................ 212 Battery ................................................................ 214 Battery conditioner .............................................. 218 EPB emergency release ......................................... 222 Park Lock emergency release ................................ 224

5 ADVICE FOR EMERGENCY SITUATIONS

Toolkit Warning Tool bag Repair work using the toolkit requires: Housed in the luggage compartment, it contains the necessary tools - suitable protective equipment (e.g., gloves) to perform a very basic repair in the event of a failure: - adequate precautions to be taken (e.g., during tire replacement • pair of cotton gloves; never lie under a vehicle raised by a jack) • set of fuses; - minimum specific expertise when working in contact with electrical parts/components (e.g., battery). • pliers for removing fuses; • tow hook; • insulated cutting pliers; • funnel for emergency fuelling; • screwdriver for slotted and Phillips head screws; • EPB emergency release tool; • Park Lock emergency release tool. 194 Advice for Emergency Situations

Warning The Electric Parking Brake (EPB) emergency release tool and the Park Lock emergency release tool may only be used by trained workshop personnel, as indicated on the label in the tool bag. Warning The Electric Parking Brake (EPB) emergency release tool is flexible and is kept folded up in the tool bag: remove the tool from its housing very carefully to prevent the end flying out. 5 Advice for Emergency Situations 195

Emergency tire repair and inflation kit Housed in the luggage compartment, the kit can be used in the Warning event of a puncture or low tire pressure to repair and/or inflate a Damage to the wheel rim that causes air leaks cannot be tire enough to continue the journey safely. repaired. Important note Warning To use the tire repair and inflation kit correctly, refer to the instruction booklet supplied with the kit. Do not remove foreign objects (screws or nails) that have penetrated the tire. Warning Warning Give the kit and instruction manual supplied with the kit to the personnel that will perform the tire repair. After using the repair kit, the vehicle must be considered in an emergency situation: drive with great care and with a maximum speed of 50 mph (80 km/h). Warning In the event of a puncture caused by foreign objects, tires with Warning cuts of up to 0.16 in. (4 mm) in diameter on the tire tread and shoulder may be able to be repaired. Apply the sticker supplied with the kit inside the vehicle where it can easily be seen by the driver to indicate that the tire has been treated with the tire repair kit. Warning Punctures cannot be repaired on the sides of the tire. Warning Drive carefully especially on curves. Warning Do not use the tire repair kit if the tire has been damaged after Warning driving with a flat tire. Avoid sudden accelerations or braking. 196 Advice for Emergency Situations

Warning Warning The kit is to be used to temporarily repair only one tire Keep the kit in its box and out of children’s reach. punctured by small objects: the kit may not be useful in the case of large punctures or tearing. Warning Important note Do not inhale or swallow the fluid contained in the cartridge and avoid contact with the skin and eyes. After driving for approximately 10 minutes, stop and recheck the tire pressure. Remember to apply the parking brake. Warning The spray contains ethylene glycol and latex, and may cause an allergic reaction, is harmful if swallowed and is irritating to eyes. Warning The spray may cause irritation by inhalation and skin contact. If the pressure has decreased below 26 psi (1.8 bar), do not Avoid contact with eyes, skin and clothing. In case of contact, continue driving: the kit is then unable to provide a tight seal rinse immediately with plenty of water. If swallowed, do not 5 because the tire may be too severely damaged. Contact your induce vomiting, rinse mouth, drink plenty of water and seek Authorized Ferrari Dealer. immediate medical advice. Keep out of reach of children. The product should not be used by asthma sufferers. Do not inhale If the tire pressure is at least 26 psi (1.8 bar), restore the vapors during use. In the event of an allergic reaction, seek correct pressure and continue driving. immediate medical advice. Store the spray can in its special case Drive very carefully to the nearest Authorized Ferrari Dealer. away from sources of heat. The liquid sealant has an expiration date: the expiration date is indicated on the kit. Warning The repaired tire must be replaced as soon as possible and the workshop personnel must be informed that the tire was treated with tire repair fluid. Advice for Emergency Situations 197

Environment Replace the spray can containing the expired liquid sealant. Do not dispose of the spray can and sealant in normal domestic waste. Dispose of in accordance with local regulations or ask your Authorized Ferrari Dealer to take care of disposal. Warning The sealant in the kit cartridge may damage the sensor inside the wheel rim on vehicles fitted with a tire temperature and pressure monitoring system (TPMS). If this occurs, the sensor must be replaced. Contact your Authorized Ferrari Dealer. Warning Wear the protective gloves provided with the tire repair kit. 198 Advice for Emergency Situations

Replacing the front and rear light bulbs Replacing license plate light bulbs To replace a license plate light bulb, proceed as follows: Important note • remove the light from the right side where there is a spring clip; To replace the front and rear light bulbs, contact your • remove the transparent cover A from its housing; Authorized Ferrari Dealer. • replace the bulb by removing connector B from its housing; To adjust the headlight beam, please contact your Authorized • refit the connector and transparent cover by inserting it first from Ferrari Dealer. the left side and then pressing on the other side. 5 B A Advice for Emergency Situations 199

Replacing other light bulbs Glove compartment, underdoor and luggage compartment bulbs Roof dome light • Use a screwdriver to gently pry under the edge of the transparent cover G and lift it. • Use a screwdriver to gently pry under the edge of the transparent cover C of the dome light and remove it from the roof panel. • Completely remove the transparent cover from its housing. • Replace the bulb D or E or F. • Take the bulb out of its clips. • Refit the dome light and make sure that the wires are not trapped • Replace the bulb. by inserting it first from the connector side and then pressing on • Refit the transparent cover and make sure that the wires are not the opposite side. trapped by inserting it first from the connector side and then pressing on the opposite side. Follow the same procedure for replacing the underdoor light bulbs and the luggage compartment dome light bulb. � � � G � 200 Advice for Emergency Situations

Light bulbs (12 V except for high beam and low beam) Type Power Low beams and high beams gas-discharge (XENON) Das Front running lights LED Front turn indicator lights LED Side turn indicator lights incandescent T4W Parking and stop lights LED Reverse lights incandescent H6W Supplementary stop lights LED Rear turn indicator lights LED Rear fog lights incandescent W16W License plate lights incandescent 5W Passenger compartment dome light Spotlights incandescent incandescent 8W 5W 5 Glove compartment light incandescent 5W Underdoor courtesy lights incandescent 5W Luggage compartment light incandescent 10W Advice for Emergency Situations 201

Replacing a fuse Fuse colors When an electrical device is not working, check that the Ampere corresponding fuse is not blown. dark yellow 5 A - Unblown fuse. brown 7.5 B - Blown fuse. red 10 Important note light blue 15 If the problem persists, contact an Authorized Ferrari Dealer. yellow 20 white 25 Important note green 30 When replacing a fuse, always use fuses of the same amperage (same color). Maxi fuse colors Ampere The tool bag contains spare fuses. yellow 20 To remove the fuses, use the pliers C in the tool bag. green 30 orange 46 red 50 � blue 60 � � 202 Advice for Emergency Situations

Location of the fuse and relay boxes A - Fuses and relays in battery compartment B - Body Computer fuses and relays C - Fuses and relays in passenger compartment on passenger side D - Fuses and relays on driver-side rear side panel C D A 5 B Advice for Emergency Situations 203

Fuses and relays in battery compartment Engine relay and fuse ECU power supply F-70 150 To access these fuses: (SCM) • remove the passenger footrest; F-71 40 Front lift pump • remove the bar T by unscrewing the two screws E; F-72 40 Parking brake power • remove the cover of box A located above the positive terminal on F-73 70 Dashboard ECU power the right side of the battery. Body Computer fuses and relays Important note To access these fuses, remove the dashboard panel 1. Only open the boxes containing the fuses that need to be checked to avoid damaging other components. Important note Only open the boxes containing the fuses that need to be Box A contains these fuses: checked to avoid damaging other components. Ref. Amp. Use CAL2 CAL2 Power supply (starter motor and alternator) E E T A 204 Advice for Emergency Situations

Box B contains these fuses and relays: Dashboard ECU devices F-39 15 Ref. Amp. Use (NBC interconnection) F-40 30 Heated rear window F-12 15 Right high beam F-42 7.5 Alternator F-13 15 Left high beam F-43 30 Windshield washer/wiper relay power supply INT/A for dashboard ECU and Body F-31 7.5 Computer Node relay coils F-44 20 Passenger seat heating, cigarette lighter Dome lights, foot well and step lights, Side F-47 30 Driver-side door, driver-side power window F-32 10 Marker relay coil Passenger-side door, passenger-side power F-48 30 F-34 30 Suspension Control Node window Stop light control, clutch control, air Rain and twilight sensor, parking sensors, F-35 7.5 conditioning node parking brake control, column adjustment F-49 7.5 control, hazard warning lights, Steering Wheel Volumetric anti-theft system, parking sensors, F-36 10 Node, Differential Control Node, radio, CAN fuel filler flap relay coil box interface Stop light control, Instrument Panel Node, 5 F-37 10 F-50 7.5 Airbag Node, weight sensor Suspension Control Node F-51 7.5 Auto Gearbox Node F-38 15 Luggage compartment lock actuator B F-72 F-73 F71 F-71 F-72 F-73 F-70 F-70 CAL2 CAL2 1 Advice for Emergency Situations 205

F-52 15 Power socket, driver seat heating Fuses and relays in passenger compartment on passenger side F-53 10 Instrument Panel Node power supply These fuses are located behind the glove compartment 2. T01 20 Low beam relay Boxes C contain these fuses and relays: T11 30 Heated rear window relay T12 30 Service relay 1 (dependent on INT/A ignition Ref. Amp. Use switch) F-01 60 +30 Radiator fan relay 2 T13 50 Jumper (service power supply 2) F-02 30 +30 ABS (valves) F-03 30 +30 Hard top Node (pump) - not used F-04 50 +30 ABS (pump) F-05 40 +30 Air conditioning Node F-06 50 +30 Radiator fan relay 1 F-07 20 +30 Horn relay F-08 7.5 Air conditioning and heating system compressor F-09 7.5 +30 Supplementary stop light relay (third stop light) 2 206 Advice for Emergency Situations

F-10 15 +30 Fuel pump relay 1 F-84 15 +30 Fuel pump relay 1 F-11 25 Left bank oxygen sensor F-85 25 Headlight washer F-14 15 +30 High beam relay F-87 25 Right bank oxygen sensors F-15 7.5 +30 Power supply for EPB-activated stop light F-88 10 +15 Left cylinder bank injection system control relay, right headlight LED module F-89 10 +15 Right cylinder bank injection system power supply relay F-91 15 +30 Tire pressure node, LH headlight LED F-16 25 +30 Right bank engine control power supply module relay F-17 25 +30 Left bank engine control power supply F-92 7.5 +30 Alternator sensing F-18 10 +30 Left cylinder bank injection system power F-93 30 +30 Ignition switch supply, LH cylinder bank injection main relay coil F-94 15 +30 Radio/CAN box/ICP/clock spring/Japan navigation system stabilizer F-19 10 +30 Right cylinder bank injection system power supply F-95 10 +30 Current stabilizer F-20 30 +30 Right cylinder bank injection system main F-97 30 +30 Stabilizer for Becker amplifier F-21 15 relay +30 Fuel pump relay 2 T02 T03 30 30 High beam relay Fuel pump second speed relay 5 F-22 15 Left bank (ignition coil) F-23 10 +30 ABS (electronic) C F-24 15 Right bank (ignition coil) F-30 30 +30 HI-FI amplifier relay F-81 40 +30 Supplementary ECU power supply F-82 70 +30 Dashboard ECU and ECU on driver-side rear side panel power supply C F-83 50 +30 Air pump relay Advice for Emergency Situations 207

T05 30 Fuel pump relay 2 T29 30 Supplementary stop light relay (third stop T06 30 Glove compartment relay light) T07 50 Horn relay T30 50 Air pump relay T08 30 Air conditioning and heating system T31 30 Headlight washer pump relay compressor relay T37 30 Radiator fan relay 2 T09 30 Left cylinder bank injection system main relay T38 30 Left headlight LED module power supply T10 30 Right cylinder bank injection system main relay relay T39 30 Right headlight LED module power supply T14 30 Fuel pump relay 1 relay T17 10/20 INT/A relay (devices excluded at ignition) T40 30 Radiator fan relay 1 T19 30 EPB-activated stop light control relay T20 30 Starting relay T26 10/20 Windshield wiper first speed relay T27 10/20 Windshield wiper second speed relay T28 30 Windshield washer pump relay 208 Advice for Emergency Situations

Fuses and relays on driver-side rear side panel F-65 20 +30 Door lock actuator To access these fuses, remove the driver-side rear side panel 3. F-66 7.5 +30 Auto Gearbox Node Boxes D contain these fuses and relays: F-67 7.5 Side Markers 2 (RH front and LH rear) Ref. Amp. Use F-78 15 +30 Battery charger F-54 15 +30 Gearbox cooling fan F-80 30 +30 Starting relay F-56 30 +30 Driving Position Node T21 50 Side Marker relay F-57 7.5 Side Markers 1 (LH front and RH rear) T22 30 Reverse light relay F-59 7.5 Reverse light power supply T23 30 Fuel filler flap relay F-60 30 +30 Passenger Position Node T24 30 Gearbox cooling fan relay F-61 7.5 +30 Driver Position Node (electronic), front lift T25 30 Auto gearbox main relay F-62 7.5 +30 Passenger Position Node (electronic) T43 30 Start enable relay F-63 15 +30 Auto gearbox main relay F-64 7.5 Fuel filler flap actuator power supply 5 D 3 Advice for Emergency Situations 209

Replacing a wheel • additional tool bag C containing the jack for raising the vehicle and the socket wrenches for operating the jack and tightening the wheel bolts. Important note If one or more wheels need to be replaced, proceed as follows: Warning • replace any wheel bolts that have damaged threads or tapers The spare wheel must only be used for short trips in the event • carefully clean the wheel bolts before fitting of an emergency. • do not lubricate the contact surfaces between the wheel bolt When the spare wheel is fitted, never exceed the maximum and the wheel rim and between the wheel rim and the brake speed of 50 mph (80 km/h) and drive carefully, especially disk. around curves and when overtaking, avoiding sudden In order not to remove the antilock coating, do not clean the acceleration or braking. wheel rim cones with solvents or aggressive products. Do not exceed the approved weight limits. Do not fit snow chains on the spare wheel. Space-saving spare wheel (optional) Never fit more than one spare wheel at a time. On request, the vehicle comes with an optional kit containing: • the spare wheel A with space-saving tire; label B indicates the maximum speed allowed of 50 mph (80 km/h) Important note Failure to comply with these instructions could lead to loss of control of the vehicle and consequently damage to the vehicle and injuries to its occupants. � � � 210 Advice for Emergency Situations

Replacing a wheel • Raise the vehicle carefully using jack E until the wheel is off the • Position the vehicle on an even surface, then block the rear wheels ground. by applying the parking brake. Warning Warning If the jack is not positioned correctly, the vehicle could slip off. Make sure that the vehicle is in a secure position by applying the Make sure that no part of the body is underneath the vehicle parking brake. while changing the wheel. The supplied jack must only be used for changing wheels. • If necessary, switch on the hazard warning lights and place a hazard triangle at the required distance from the vehicle. • Unscrew the five bolts and remove the wheel. • Take the spare wheel and tools out of the luggage compartment. • Fit the uninflated space-saving spare wheel. • Loosen the five wheel bolts approximately one turn each using • Screw the bolts into place but do not tighten them. wrench D supplied. • Place the base of the jack E on flat firm ground under one of the Warning jacking points F on the underfloor as shown in the figure. Inflate the collapsible spare wheel before lowering the vehicle to avoid damaging the rims. 5 • Inflate the space-saving spare wheel using the inflation kit. F E D Advice for Emergency Situations 211

Towing Warning When towing the vehicle, use only the attachment point provided The kit must be used in “tire inflation” mode. Refer to the for the towing hook A inserted in housing C. instruction manual supplied with the kit. Proceed as follows: • Take tow hook A out of the tool bag. • Inflate the spare wheel to the indicated pressure (see page 31). • Open cover B in the right-hand side of the front bumper. • Lower the vehicle and remove the jack. • Tightly screw tow hook A into housing C. • Tightly fasten the stud bolts, alternately going from one stud bolt • Release the EPB. to one that is diametrically opposite. • Release the Park Lock. As soon as possible, tighten the bolts with the torque wrench to a torque of 73.76 ft. lbs. (100 Nm). Warning If there is an electrical system failure, release the EPB and Park Warning Lock manually (see pages 222-224). The spare wheel does not have a tire pressure monitoring sensor (see label on spare wheel tool bag). After fitting, it is not checked by the system but complies with international regulations ECE R64/01. After fitting, we recommend that you go to the nearest Authorized Ferrari Dealer. A B 212 Advice for Emergency Situations

Fuel inertia switch Warning The fuel inertia switch is a safety device which is designed to While towing the vehicle, you must comply with road deactivate the fuel pump relays if a collision occurs. regulations. A symbol appears on the left TFT display and the hazard warning lights come on to indicate that the switch has been activated. When the fuel inertia switch is activated, the doors are also Warning unlocked (if locked) and the central dome light comes on. Do not tow the vehicle using the hook attached to the suspension levers, or wheel rims but only to the tow hook Warning properly fitted in place. The fuel pump relays can be reactivated by pressing the button Keep the key in position II to enable the lights to work and A in the battery compartment which can be accessed by opening prevent the steering wheel from locking if it is turned; when the passenger side footrest. towing the vehicle, do not start the engine. Important note Remember that when the engine is turned off, the power steering and brake servo functions do not work. 5 A C Advice for Emergency Situations 213

Battery Disconnecting the battery The battery is located in the passenger compartment behind the Before disconnecting the battery, deactivate the electronic alarm passenger side footrest. using the remote control. Checking the battery Warning Never disconnect the battery from the electrical system when Warning the engine is running. The battery does not need topping up with distilled water or Before disconnecting the battery, lower the side windows by at sulphuric acid. least 0.8-1.2. in. (2-3 cm) to avoid damaging the weather strips when opening and closing the doors. Warning Warning The battery must only be removed from the vehicle by an Authorized Ferrari Dealer. The windows must remain lowered until the charged battery is reconnected. If the battery is discharged and the windows are fully up, only open the doors when strictly necessary and take Warning great care; do not close them again until the windows can be lowered. Do not place the battery near sources of heat, sparks or open flames. Important note The vehicle is equipped with a sealed lead acid battery that does We strongly recommend using the battery conditioner if the not require maintenance. vehicle is going to left unused for a long period (see page 218). • Periodically check that the terminals and posts are clean and firmly secured. To cut off the power supply from the battery to the electrical • Visually inspect the outer casing for any cracks. system, use the quick release C on the left side of the battery. Use • If the battery overcharges, it will wear out quickly. Have the the locking lever to loosen the terminal. vehicle electrical system checked if the battery tends to discharge easily. 214 Advice for Emergency Situations

Detach the terminal from the battery: the power supply from the Reconnecting the battery battery to the electrical system is cut off. Place the clamp on the battery and fasten it by closing the locking lever. Warning Each time the battery is reconnected, do the following before starting the engine: The battery quick release must only be used if the battery conditioner cannot be connected. - close both doors and close the luggage compartment lid; unlock and lock the doors using the remote control; open the luggage compartment lid using the remote control; Warning - adjust the clock (date and time on instrument panel); Place the terminal so that it does not come into contact with the - close both doors and fully raise the driver side and passenger side battery terminal or other metal parts of the vehicle. windows to their upper limit; check that the windows move down to the “target position” when the doors are opened. Warning Before starting the engine, wait at least 60 seconds with the ignition key in position II to allow the electronic system that controls the motor-driven valves and the AC ECU to run a self- acquisition process. 5 During this period, do not activate any devices. The Motronic ECU self-acquisition cycle will only function correctly C when the intake air temperature is above 41 °F (5 °C). After removing the battery from the vehicle or disconnecting it from the electrical system, it is important to check that the external temperature is within the indicated values when reconnecting before performing the self-acquisition cycle. Advice for Emergency Situations 215

Emergency starting To perform an emergency start, do the following: If the battery is dead, you can perform an emergency start by • Apply the parking brake. connecting jumper cables to the battery of another vehicle, a • Deactivate all the electrical devices. portable jump starter or an external battery. • Remove the bar T by unscrewing the two screws E. • Remove cover F of the fuse box located above the positive Important note terminal on the right side of the battery. Emergency starting can only be performed with batteries with a • If emergency starting is performed using the battery of another nominal voltage of 12 V. vehicle, leave the engine on the other vehicle at idle. • Using the jumper cables, connect the positive terminal of the battery to the positive terminal of the portable jump starter or Important note external battery going from the battery on your own vehicle. For emergency starting, only use cables that do not allow reverse • Connect the negative terminal of the portable jump starter or polarity, with sufficient cross-section and insulated clamps. external battery to an earthing point on your vehicle using the jumper cable going from the external battery. • Start the engine. E E T F 216 Advice for Emergency Situations

• Disconnect the jumper cable from the grounding point and then from the positive terminal of the battery on your vehicle. Warning After emergency starting, go to the nearest Authorized Ferrari Dealer immediately to get the battery checked. 5 Advice for Emergency Situations 217

Battery conditioner After connecting the battery conditioner to the socket in the vehicle, run the connection cable under the passenger door on the The vehicle is equipped with a battery conditioner to maintain and front side, and then connect the other end to an electrical outlet. recharge the battery. Important note Important note Do not run the connection cable out of the vehicle in positions Using the battery conditioner will help extend the life of the other than those indicated to prevent damaging the seals and/or battery. the cable. The device is kept in a pocket inside the car cover bag supplied If you do not plan to use the vehicle for over a week, we with the vehicle. recommend you connect the battery conditioner to keep the battery The battery conditioner connection socket D is located under the in working order. dashboard on the passenger side. Warning Warning The engine cannot be started as long as the battery conditioner Place the battery conditioner where it can be easily seen away is connected to the vehicle socket. from heat sources and out of children's reach. D 218 Advice for Emergency Situations

Exhaust system overheating alarm devices (“Slow Down” Important note function) Additional technical information on the use of the device can If the engine is running unevenly resulting in exhaust system be found in the manual provided inside the pocket of the car overheating, the “Slow Down” function is activated: a special cover bag. Use the battery conditioner only as instructed in the symbol (see page 130) appears on the left TFT display manual. accompanied by a message. The message varies according to three alarm levels: • Temperature high: “Catalysts temp. high. Slow down”. • Temperature too high: “Catalysts temp. too high. Engine performance limited”. • Catalytic converter temperature system failure: “Catalysts temp. not plausible. Go to dealer slowly”. Displaying of the message is controlled by the thermistor via the engine control ECU. Warning Incorrect use of the vehicle may cause the “Slow Down” 5 function to be activated. Warning If the temperature is high: slow down immediately so that the exhaust system temperature decreases. Advice for Emergency Situations 219

Clutch overheat alarm devices Warning Extremely high performance use of the vehicle at high engine If the temperature is too high: speeds for prolonged periods and at high ambient temperatures the temperature in the catalytic converters has reached a may cause the DCT gearbox clutches to overheat. In this case, the dangerous level and could damage them; if you continue to following safety warnings will be displayed on the left TFT display, drive, the engine control ECU intervenes and reduces the corresponding to two different alarm levels: torque produced by the engine. • The message “Clutch overheated” The torque limit remains active until the catalytic converter • The message “Clutch overheated” accompanied by an audible temperature goes down to normal operating values. warning signal. When the message “Clutch overheated” is displayed, the driver may notice a difference in the behavior of the system during gearshifts Warning and/or during standing starts. If catalytic converter temperature system failure information is displayed: - the engine control ECU intervenes and reduces the torque produced by the engine - the driver must slow down and slowly drive to the nearest Authorized Ferrari Dealer to have the engine parameters checked. Warning If the OBD warning light (see page 129) illuminates at the same Clutch time as the “Slow Down” message, go to the nearest Authorized overheated Ferrari Dealer to have the ECU error memory checked. Do not proceed in any other way. 220 Advice for Emergency Situations

Engine malfunction alarm devices Important note If the “on boar diagnostic system” (OBD, see page 129) warning Certain high-performance actions (such as, but not limited to: light flashes or illuminate permanently while the engine is running, “Performance Start” function, standing start with wheelspin with it indicates that the engine or the emission control system may be Manettino set to CST OFF, etc.) may be inhibited to prevent malfunctioning. excessive overheating of the clutches: the system warns the The electronic system detects and isolates the error preventing driver that the action is not permitted by displaying the message damage to the engine or the production of harmful emissions. “Operation not admissible” on the left TFT display. Warning Warning When the “engine diagnostic system failure” warning light As soon as any of the warnings described above appear on illuminates, engine performance may be considerably reduced. the left TFT display, the driver must slow down and continue Drive carefully, avoiding sudden acceleration and high speeds. driving at an engine speed between 2000 and 3000 rpm and Contact your Authorized Ferrari Dealer immediately. minimizing gearshift frequency to allow the clutches to cool down as quickly as possible. These driving conditions must be maintained until the message “Clutch overheated” is no longer displayed. Contact your Authorized Ferrari Dealer if this condition 5 persists. Advice for Emergency Situations 221

Replacing the brake pads and discs Emergency release of the electric parking brake (EPB) Brake pads The front brake pads have a wear detector connected to the brake Warning warning light; if this warning light illuminates or braking is not The release procedure must only be carried out by trained even, have the pad thickness and the state of the braking surfaces workshop technicians. checked. If the system cannot be released, contact the nearest The minimum brake pad thickness is 0.12 in. - 3 mm (thickness of Authorized Ferrari Dealer. the friction material only). Replacing brake pads When the brake failure warning light illuminates, it means that Warning the front brake pads are excessively worn and must be replaced When the electric parking brake is deactivated manually, the immediately. vehicle may move. To keep the vehicle stationary, the Park Lock safety device must Warning be applied: make sure that the letter “P” appears on the gearbox To help ensure the quality of the components and proper display. installation, we recommend that you have the brake pads replaced at an Authorized Ferrari Dealer. After replacement, avoid sudden braking until the new pads are seated properly (approximately 186 mi / 300 km). A 222 Advice for Emergency Situations

If the electric parking brake cannot be deactivated because the battery is dead or there is a failure in the electrical system that Important note controls it and the vehicle needs to be moved, the emergency To release the brake completely, the wrench must be turned release procedure described below must be performed. 50 times, whereas it starts to be released after approximately • Take wrench A for EPB emergency release out of the tool bag. 20 turns. Warning Once the electric parking brake has been manually released, the Wrench A may only be used by trained workshop technicians, as EPB node records a failure at the next key-on and a special symbol indicated on label C on the tool bag. and the following message are displayed on the left TFT display: “Parking Brake system revision. Go to dealer”. • Place the release wrench A in the hole B on the rear RH gravel guard and turn clockwise: this loosens the parking brake cables. Warning The parking brake resumes normal operation, but it is important to go to the nearest Authorized Ferrari Dealer to have it calibrated and delete any errors in the error memory. Go to an Authorized Ferrari Dealer. Calibration is necessary for safety reasons. 5 C B Advice for Emergency Situations 223

Park Lock emergency release Warning Warning When the Park Lock safety device is deactivated manually, the vehicle may move unexpectedly. The emergency release procedure must only be carried out by trained workshop technicians. The vehicle is only kept stationary by the parking brake, if applied. If the system cannot be released, contact the nearest Authorized Ferrari Dealer. The Park Lock manual emergency release device is found in the engine compartment, in line with the gearbox next to the filter Warning housing, as shown by the arrow in the figure. To perform the Park Lock emergency release procedure, do the This should be avoided unless absolutely necessary: following: - to tow the vehicle; • Take wrench D out of the tool bag. - if there is a Park Lock failure (displayed on the left TFT display with the message “Only manual unlock gearbox allowed: See handbook”). Warning Wrench D may only be used by trained workshop technicians, as indicated on label C on the tool bag. C D 224 Advice for Emergency Situations

• Open the engine compartment lid. If the electrical system allows it, check that the letter “N” appears • Extend wrench D and place it in the manual release device on the gearbox display by turning the ignition key to position II. housing keeping it at an angle so that it can reach the housing. The following message will appear on the left TFT display: “Gearbox not in Parking position”. At the same time, an audible signal is repeated four times to indicate that it has been released. Important note Make sure that notch G of wrench D fits onto pin H in the housing of the device. • Once the wrench has been placed in the housing, lightly press down on the filter housing to bring to wrench at right angles to the housing. • To perform the emergency release, turn wrench D counterclockwise for a quarter turn. 5 G H Advice for Emergency Situations 225

Warranty Book .................................................... 228 Maintenance ....................................................... 228 Level checks......................................................... 230 Wheels and tires .................................................. 237 Maintenance of the seat belts and pretensioners ... 239 Cleaning the vehicle ............................................. 239 If the vehicle is stored for long periods .................. 243

6 CARE OF THE VEHICLE

Warranty Book Maintenance schedule The vehicle comes with a “Warranty Book”. At the intervals prescribed, the Authorized Ferrari Dealer must This contains the vehicle’s warranty terms and conditions. perform all the fine-tuning and maintenance checks indicated in the “Warranty Book”. Important note It is however advisable to report any small fault which occurs when using the vehicle (e.g., small leaks of essential fluids) to your The warranty book also contains special blank spaces Authorized Ferrari Dealer immediately and not wait until the where the Authorized Ferrari Dealer can register the next service is due to correct the problem. regular maintenance services performed, as indicated in the Periodic maintenance services must be performed at least once a maintenance schedule. year even if the specified mileage limit has not been reached (see “Yearly Maintenance” in the “Warranty Book”). Maintenance Displaying information on scheduled maintenance It is essential to always keep the vehicle in proper working order to help ensure a long working life and to prevent any running defects If the next scheduled maintenance deadline is approaching, at caused by negligence or lack of maintenance, and consequently to key-on, the message “Service Stop within:” is displayed for 5 avoid hazardous situations. seconds on the left TFT display followed by the number of miles (kilometers) or days before vehicle servicing. The information is provided in miles (kilometers) or days according to the deadline Important note that comes first. All repair work on any safety system component must be performed by your Authorized Ferrari Dealer. Service stop within: 100 mi 228 Care of the vehicle

Information on scheduled maintenance can also be displayed on the left TFT display if requested by the driver irrespective of the scheduled deadlines. To do this, call up the MENU screen page (see page 110) and select “Service”. Chassis and bodywork maintenance The chassis has technological and manufacturing specifications that require that any operation be performed by staff specially trained to work with this innovative technology. It is of critical importance to use special equipment tested by Ferrari to ensure that the repair work is performed in accordance with Ferrari's specifications. Important note If the chassis is damaged in an accident, Ferrari advises customers to contact your Authorized Ferrari Dealer. The chassis, under standard conditions of use, requires no maintenance; it is however advisable to contact your Authorized Ferrari Dealer at the intervals indicated in the “Warranty Book” in order to have it checked. 6 Care of the vehicle 229

Level checks Ref. Page Ref. Page A Engine oil tank cap 232 D Brake fluid tank cap 235 B Coolant tank cap 234 E Windshield/headlight washer fluid tank cap 236 C Power steering oil tank cap 234 A B D E C 230 Care of the vehicle

Important note The fluid level checks must be performed at the intervals indicated in the “Warranty Book” or, in any case, before starting a long journey. Environment All the materials used for the following operations (e.g., cloths soaked with oil or grease, pans, etc.) must be disposed of in compliance with local environmental protection regulations. Important note Only use lubricants and/or fluids recommended by Ferrari (see the “Recommended Lubricants and Fluids” table on page 34). 6 Care of the vehicle 231

Checking the engine oil level Important note Warning The distance between the MIN and MAX reference marks corresponds to approximately 2.11 qts. (2 litres) of oil. The engine oil level must be checked when the engine is idling and warm and the vehicle is on level ground. DO NOT add oil with different characteristics from those of the 7. Top up if necessary with the recommended oil and make sure oil already in the engine. you do not fill beyond the MAX level on the dipstick. The symbol, shown below, on the left TFT display and the message Warning “Check engine oil level” inform the driver that the engine oil level If the oil level is below MIN, top it up and then have the system must be checked. checked by your Authorized Ferrari Dealer. 8. Screw the cap back on tightly. Proceed as follows: 1. Run the engine until the engine oil temperature has reached 194 °F (90 °C). 2. Let the engine idle. 3. Wait 2 minutes and then open the engine compartment lid and unscrew oil tank cap A. 4. Clean the dipstick on the cap. A 5. Rest cap A on the tank filler neck with the cap spring in its housing as shown in detail M. 6. Remove the cap and check that the level is between the MIN and MAX notches on the dipstick. 232 Care of the vehicle

After topping up, the “low oil level” symbol on the left TFT Checking the DCT gearbox oil level display may remain on for some time, and is considered normal. This will allow the system to perform all the necessary checks. Important note 9. When you have added or changed the oil, check the oil level once again as indicated above. We recommend that you have the oil level of the DCT gearbox checked by your Authorized Ferrari Dealer. Environment Top up with care to avoid spilling the oil out of the filler neck. M MAX MIN 6 Care of the vehicle 233

Checking the coolant level Checking the power steering system oil level Warning Warning The coolant in the cooling system reaches very high The power steering oil level must be checked with the engine temperatures and pressures. This procedure must always be warm, after having driven at least 9 mi. (15 km). If it is checked performed when the ENGINE IS COLD. Never remove the cap when the engine is cold, the level may appear to be very low from the expansion tank when the engine is running or warm. even when the recommended amount of oil is in the system. • Check that the level comes up to the dotted line shown in the figure. Warning • If the level is low, remove the cap B from the expansion tank and If the oil level is below MIN reference mark, top it up and then top up with the recommended coolant. have the system checked by your Authorized Ferrari Dealer. Important note Proceed as follows: If frequent top-ups are required after short trips, have the • Remove cap C with the dipstick from the tank. system checked by your Authorized Ferrari Dealer. • Screw the cap B back on tightly. B C 234 Care of the vehicle

• Check that the power steering oil level is between the MIN and Checking the brake fluid level MAX levels on the dipstick. The brake fluid tank is located under the right-hand under- • If the level is near the MIN reference mark, top up with the windshield protective cover. Proceed as follows: recommended oil up to the MAX level. • Remove cover P, remove cap D and check that the fluid is near the MAX mark shown in the figure. Warning Always use the indicated quantity of new, recommended fluid Important note taken from sealed containers. Clean cap D before removing it The fluid in the circuit is synthetic. The use of mineral-based fluid may irreparably damage the rubber system gaskets. • If the level is near the MIN mark shown in the figure, top up with the recommended oil to the MAX mark. • Screw the cap C back on tightly. Warning Environment Always use the indicated quantity of new, recommended fluid Do not dispose of used fluid in the environment. taken from sealed containers. D MAX 6 MAX P MIN MIN Care of the vehicle 235

Windshield and headlight washer fluid Environment The windshield and headlight washer fluid tank can be accessed by lifting the luggage compartment lid. Never dispose of used fluid in the environment. • Lift the cap E and fill the tank with the recommended fluid (see the “Recommended Lubricants and Fluids” table on page 34) Warning until it can be seen in the fluid filling neck. • Close cap E. The fluid in the brake system may damage plastic, rubber and painted parts and is highly dangerous if it comes into contact with the eyes or the skin. If the fluid comes into contact with the eyes or skin, wash the affected part thoroughly with running water. To avoid any risk, always use protective goggles and gloves. Keep out of the reach of children! Warning The use of mineral-based fluids will irreparably damage the system rubber gaskets. Do not use fluids other than those already in the system for topping up. E • Screw cap D back on tightly. 236 Care of the vehicle

Wheels and tires Low tire pressure can lead to overheating, internal damage and even destruction of the tires. To help ensure maximum performance and tire life and to permit the best tire adjustment on the wheel rim, it is important to comply with the following instructions for the first 125/185 mi Warning (200/300 km) with new tires: Inflating the tires to a pressure other than that prescribed will • avoid sudden acceleration render the TPMS monitoring system inaccurate. • avoid sharp braking and steering • drive at moderate speed on straight roads and on curves. Sudden impact with pavements, potholes and other obstacles of various types as well as long trips on rough roads can cause damage How to use the tires to the tires that is not always visible to the naked eye. Check the tires regularly for any signs of damage (e.g., scratches, cuts, cracks, bulges, etc.). Remember that tires deteriorate over Important note time, even if they are rarely used or not used at all. To help ensure safe driving, the tires must be kept in good If sharp objects penetrate the tires, they can cause damage which is condition. Always check your tires regularly for wear and only visible when the tire is removed. damage. Have any tire damage inspected by an expert as it may considerably reduce tire life. The inflation pressure must correspond to the specified values and Cracks in the tread and side walls, possibly accompanied by must be checked only when the tires are cold since tire pressure bulging, are sure signs of ageing. increases as tire temperature increases. Never reduce the pressure if the tires are hot. 6 Environment Periodically check the tire pressure. Driving with the tires inflated to the correct pressure helps to reduce fuel consumption. Care of the vehicle 237

Warning Warning Your Authorized Ferrari Dealer has the necessary equipment The tires are of the “directional” type and there is an arrow for tire replacement. marked on their side wall to indicate the direction in which Have the tires replaced by an Authorized Ferrari Dealer that they must rotate or which side is the outer side. When replaced, has the necessary equipment available to avoid causing damage maximum performance levels can only be ensured if the rotation through carelessness to the sensor located inside the wheel rim. direction corresponds with the direction indicated by the arrow. Ensure that tires are not kept in storage for more than 4 years. Tires on the same axle must always be replaced in pairs. The maximum limit for keeping tires in storage is 4 years provided they are kept away from sunlight, bad weather and Regularly check the tire tread (minimum acceptable depth 0.67 in. damp and where there is a low oxygen content. - 1.7 mm). As the tread wear increases, there is a greater risk of skidding. Important note Warning Your Authorized Ferrari Dealer can certify whether aged tires Drive carefully on wet roads to reduce the risk of “aquaplaning”. are suitable for use. In any case, tires that have been on a vehicle for more than 3 years must be checked by an Authorized Ferrari Dealer. Wheel alignment check and adjustment When you notice unusual wear of the tires and in any case, at the intervals prescribed in the “Warranty Book”, have your Authorized Warning Ferrari Dealer check the vehicle alignment. We recommend replacing tires at least every 4 years, even with only minimal use. Frequent use in maximum load conditions and at high temperatures may accelerate aging. Never fit tires of uncertain origin. 238 Care of the vehicle

Maintenance of seat belts and pretensioners Cleaning the vehicle • Periodically check that the anchor points are tight and that the Cleaning the exterior seat belt is in perfect condition and slides smoothly. • The seat belt must be kept clean; the presence of any dirt could prevent the seat belt retractor from working properly. Environment • To clean the seat belt, wash it by hand with mild soap and water, All the materials used for the following operations (e.g., cloths rinse it and let it dry. Do not use strong detergents, bleach or soaked with oil or grease, pans, etc.) must be disposed of in aggressive solvents, as they can weaken the fibers. compliance with the environmental protection regulations. • Do not let the seat belt retractors get wet: proper functioning is only ensured if they are kept dry. Proper care of the vehicle on the part of the owner is essential for • The pretensioner requires no maintenance or lubrication. If long vehicle life. immersed in water or mud, the pretensioner must be replaced. Here is a list of the main precautions to be taken. • The pretensioner must be replaced at the intervals indicated in • Certain parts of the vehicle should not be left wet or dirty for the “Warranty Book”. long periods of time: in particular, the passenger compartment floor and the luggage compartment must always be kept clean and dry. The draining holes under the doors should be kept unclogged to allow any water to drain. • The underbody and the lower surfaces of the vehicle should be cleaned regularly, and more frequently (at least once a week) if the vehicle is used on salty or rough roads. The vehicle should be cleaned thoroughly and carefully: cleaning that merely wets encrusted mud without removing it completely can prove 6 damaging. • The vehicle must be washed regularly with suitable equipment. Do not use very hot water or steam to clean the paintwork and the lower surfaces. It is advisable to soften any dirt first, then remove it with a jet of water at room temperature. Care of the vehicle 239

Cleaning and care of matt paintwork (optional) Important note Do not use aggressive products for cleaning the windows. Warning The use of aggressive products could seriously damage the The paintwork MUST NOT be polished using any type of bodywork. product. • Do not wash the vehicle in direct sunlight or when the bodywork Owners must take great care of vehicles with matt paintwork is still warm: make sure that the jet of water does not blast the (optional). paintwork; wash the vehicle with a sponge and a mild soap and Here is a list of the main precautions to be taken. water solution; rinse the vehicle again with a jet of water and dry it with a chamois leather. • Wash the vehicle using a steam cleaner and rinse with demineralised water only. Important note • It must be dried using an automatic dryer or compressed air. Manual drying can ONLY be performed using a 3M microfibre When the vehicle has been washed, apply slight pressure to the yellow cloth (Ferrari code 571.400.022) that is clean and soaked brake pedal at moderate speed before driving at a normal speed, in demineralised water in the areas where limescale deposits are until the brake discs and pads have cleaned off. present. The cloth must be kept in a special clean container. • To clean any grease or oil marks, a 3M microfibre yellow cloth In order to maintain the shine on the paintwork, polish it once or (Ferrari code 571.400.022) that is clean and soaked in R107/S twice a year with products recommended by Ferrari. solvent (heptane) can be used. A new cloth must be used and it • Any areas that are cracked or chipped by stones, scratches or must not have been previously soaked in demineralised water. parking manoeuvres, etc., must be immediately repaired by your • Do not wash the vehicle in direct sunlight or when the bodywork Authorized Ferrari Dealer. is still warm. • Do not park the vehicle in damp and/or unventilated areas for • Do not apply stickers to the bodywork. long periods of time. 240 Care of the vehicle

• Any areas that are cracked or chipped by stones, scratches or parking maneuvers, etc., must be immediately repaired by your Important note Authorized Ferrari Dealer. Avoid the film coming into contact with the brake fluid: the film will become opaque. Important note DO NOT lean against the vehicle especially if you are wearing • Do not use solvents along the edges of the film to keep them from clothes with buttons, buckles or are wearing rings, necklaces, penetrating inside the adhesive layer. etc. This may cause irreparable damage to the bodywork. Important note Important note Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Light Blue, Met Sky-Blue and Fuji White vehicles must be To use suitable products, contact your Authorized Ferrari washed every month and waxed at least twice a year so that dirt, Dealer. acid rain, pollutants, etc. do not penetrate the pores of the film and cause it to tarnish. Cleaning of protective anti stone-chipping film (optional) Important note The film has been designed to help protect the bodywork: anything that damages the paint will also damage the film. We recommend that the film be replaced every 24 months for Nürburgring Silver, Avus White, Alloy Grey, Met Avio, Ivory, Met Warning Light Blue, Met Sky-Blue and Fuji White vehicles, which may Do not pour denatured ethyl alcohol, acetone, isopropyl alcohol, show a light visible tarnish due to dirt inside the pores of the film. 6 heptane or substances that contain these compounds on the film. It should be noted that timely and accurate cleaning (monthly washing and waxing twice a year at least) will help prevent • Do not apply adhesive elements on the film. deterioration of the film. • When cleaning, do not use metal or abrasive substances in general and acid chemical compounds. Care of the vehicle 241

Cleaning the interior Cleaning and care of the Alcantara® upholstery Cleaning and care of the leather upholstery Warning As indicated in the “Maintenance Schedule” (see the “Warranty Do not use steam cleaners. Booklet”), proper and regular treatment, at least once a year, will help preserve the quality, natural characteristics and softness of the leather upholstery in your Ferrari. • Carefully dust the parts to be cleaned With this in mind, specific leather care products are also available • Use a soft cloth or sponge moistened with clean water (“Cleaner” and “Cream”) both tested by Ferrari. • Thoroughly wring out the cloth and wipe it over the entire These products can be ordered through an Authorized Ferrari Alcantara® area making sure you do not overwet it Dealer, both individually and as part of the “Care Kit” which • Repeat the procedure includes the complete range of products for cleaning the vehicle. • Let it dry completely • To recondition the material, gently use a brush with soft bristles. Important note For use of the “Care Kit” products, contact your Authorized Ferrari Dealer. The following products must be avoided when cleaning the leather: harsh detergents, turpentine, liquid stain removers, petrol, solvents and domestic cleaning products. All of these products damage the natural material. 242 Care of the vehicle

If the vehicle is stored for long periods If the vehicle is not used for long periods of time, certain precautions should be taken: • if possible, park the vehicle on a level surface in a covered and well-ventilated area • prevent the vehicle from moving by engaging a gear • bring the tire pressure to 43.5 psi (3.0 bar) and periodically change the point where the tires rest on the ground • connect the battery conditioner Important note If you do not want to connect the battery to the battery conditioner in order to keep certain devices functioning such as radio station memory, alarm system, etc., the battery must be recharged at least once a month. If the vehicle is not used for long periods of time without connecting the battery conditioner, the battery must be recharged at least every three months. • protect the vehicle with a breathable fabric cover and avoid materials that prevent any dampness on the bodywork from evaporating. Before using the vehicle again after long periods of inactivity, adjust 6 the tire pressure to the indicated pressure and check the fluid levels of all the systems. Care of the vehicle 243

Glossary .............................................................. 247

7 GLOSSARY

Abbreviation Meaning ABS (Anti-lock Braking System) The ABS is designed to help prevent wheel locking when braking so that vehicle handling can be maintained. AC Air conditioning. ASR Anti-skid regulation during acceleration. Autopark Automatic activation of the electric parking brake (EPB) when the engine is switched off. This function can be disabled. Auto easy exit Simplified function gear shifting. To exit “Auto easy exit” mode, simply operate one of the two shift paddles. AVH Automatic Vehicle Holding Additional function of the electric parking brake (EPB): it allows gradual release of brake shoes/pads when the vehicle starts up. This helps ensure an optimized release for the vehicle and is an aid for the driver. CST Stability and Traction Control. It consists of two systems: VDC and F1-Trac. DCT Dual Clutch Transmission: each clutch is associated with a part of the gearbox, one is designed for engaging even gears, the other for odd gears. Once a gear has been engaged, the system has already preselected the next one. After reaching the correct RPM, a clutch opens and at the same time the other one closes, so that the traction force is not interrupted. E-Diff 3 Evolved electronic differential integrated with the F1-Trac traction control. EBD Electronic Brake-Force Distribution Electronically-controlled brake-force distribution. ECU Electronic Control Unit. EPB Electric Parking Brake: the system operates by means of an ECU and an electric motor on the rear brake shoes. F1-Trac Traction control derived from the technologies used in the racing sector. The system can estimate the maximum available grip in advance by continuously monitoring the appropriate wheel speed and using an auto-adaptive operating 7 logic. Comparing this information with the vehicle dynamics model stored in the control system, F1-Trac, optimizes the vehicle behavior by controlling engine torque delivery. Glossary 247

Abbreviation Meaning FBP (Ferrari Brake Prefill) System that helps eliminate the distance between the brake pads and discs by applying slight pressure to the braking system as soon as the accelerator pedal is released just before braking. This results in more immediate brake response. Manettino The driving mode control switch on the steering wheel which allows the driver to use vehicle potential in a quick, intuitive way. Park Lock Automatic DCT gearbox park lock. When the engine is off, a mechanical lock is designed to activate automatically to prevent the vehicle from moving if the electric parking brake is not activated. Performance Start Strategy for performance starts from a stopped position in a controlled environment such as a racetrack. TFT displays Multifunction color displays on the instrument panel that provide vehicle information. TPMS Tire Pressure Monitoring System. Using special sensors fitted inside the wheel rims next to the air valve, the data measured is sent to an ECU. The data and messages are displayed on the left TFT display. Traction power Force exerted by the vehicle on the road surface through the wheels; it indicates the grip. VDC Vehicle Dynamic Control performed through the braking system and engine torque. Xenon headlights Headlights on the front of the vehicle that produce a more intense beam by using a voltaic arc rather than an incandescent spiral. 248 Glossary

Table of Contents ................................................ 252

8 TABLE OF CONTENTS

Index B BabySmart system ......................................................................... 78 Basic seat ........................................................................................ 176 Battery ............................................................................................. 214 A Battery conditioner .................................................................... 218 Before a trip .................................................................................. 152 Abbreviations/Acronyms ........................................................... 10 Before you drive .......................................................................... 159 ABS and EBD ................................................................................. 84 Brake fluid level .......................................................................... 235 Activating the Cruise control ................................................. 139 Brake pads ..................................................................................... 222 Activation of the electronic alarm .......................................... 19 Active safety .................................................................................... 57 C Additional Occupant Protection Systems ........................... 70 Adjusting brightness .................................................................. 111 Capless filler neck ...................................................................... 103 Adjusting the air vents .............................................................. 187 Carwash procedure .................................................................... 172 Adjusting the steering wheel ................................................ 182 Checking the battery ................................................................. 214 AFS2 adaptive headlights (optional) ................................. 150 Child safety ...................................................................................... 64 Air conditioning and heating system ................................ 184 Child seat anchorage ................................................................... 68 Air recirculation .......................................................................... 186 Chronometer operating logic ................................................ 115 Alarm memory ................................................................................ 21 Chronometer screen page ....................................................... 115 Alarm system ................................................................................... 17 Cleaning of protective Alcantara upholstery .................................................................. 242 anti stone-chipping film (optional) .............................. 241 Automatic Vehicle Holding .............................................. 87, 171 Cleaning the exterior ................................................................ 239 Autopark function ................................................................ 87, 171 Cleaning the interior ................................................................. 242 Auto easy exit gearbox mode ................................................ 158 Cleaning the parking sensors ................................................ 123 Auto gearbox mode ................................................................... 158 Cleaning the vehicle .................................................................. 239 AVH function ......................................................................... 87, 171 Closing the engine compartment lid .................................... 97 Closing the fuel filler flap ...................................................... 102 Closing the luggage compartment lid .................................. 99 252 Table of Contents

Clutch overheat alarm devices .............................................. 220 DOWN shift paddle ................................................................... 143 Consulting the manual .................................................................. 9 Driver-side power window .................................................... 104 Controls on the steering wheel ............................................ 140 Driver’s seat position memory (Full Electric option) .. 179 Coolant level ................................................................................. 234 Driver and passenger airbags .................................................. 71 Cruise control (optional) ........................................................ 138 Driving in fog ............................................................................... 161 CST - Stability and Traction Control ................................... 85 Driving in the rain ..................................................................... 160 CST OFF mode ................................................................ 141, 166 Driving on mountain roads .................................................... 161 CT OFF mode ................................................................... 141, 166 Driving on snowy or icy roads .............................................. 161 Driving style .................................................................................... 11 D Driving the vehicle ............................................................. 48, 153 Day lights ........................................................................................ 148 Driving using the driving mode DCT gearbox oil level ............................................................... 233 control switch ("Manettino") ......................................... 164 Deactivating the anti-lift alarm ................................................ 21 Driving with the "ABS" braking system ........................... 162 Deactivation of the electronic alarm ..................................... 20 Duplicating the keys .................................................................... 18 Digital speed screen page ........................................................ 137 E Dimensions ...................................................................................... 28 Direction indicators ...................................................................... 47 E-Diff 3 ............................................................................................. 86 Disconnecting the battery ....................................................... 214 Electrically-adjustable seat (optional) ............................... 178 Display setting and configuration Electric parking brake ........................................................ 87, 170 of vehicle parameters ......................................................... 110 Electric system ............................................................................... 29 Dome light ..................................................................................... 151 Electronic alarm ............................................................................ 19 Doors .......................................................................................... 38, 96 Electronic tachometer ............................................................... 133 Doors, engine or luggage compartment lid open Emergency exit from inside function display .................................................................... 127 the luggage compartment ................................................. 100 Door lock/unlock ....................................................................... 151 Emergency opening of the fuel filler flap ....................... 102 DOT quality grades ...................................................................... 32 Emergency opening of the luggage compartment lid ... 99 DOWN-shifting .................................................................... 51, 156 DOWN-shifting due to underrevving ................................ 156 Emergency release of the electric parking brake .......... 222 Emergency starting .................................................................... 216 8 Table of Contents 253

Emergency tire repair and inflation kit ............................ 196 G Engine compartment lid ............................................................ 97 Engine malfunction alarm devices ...................................... 221 Gear display .................................................................................. 134 Engine oil level ............................................................................ 232 General notes .................................................................................... 4 Engine RPM LED on steering wheel (optional) ........... 134 Glossary .......................................................................................... 247 ENGINE START button ......................................................... 140 Glove compartment ................................................................... 188 Environmental protection ......................................................... 11 EPB ............................................................................................ 87, 170 H ESCAPE function ....................................................................... 125 Hazard warning lights ....................................................... 47, 149 Exhaust system overheating alarm devices ...................... 219 Headlight washer ........................................................................ 144 External lights and turn indicators ....................................... 46 High beams ........................................................................... 46, 146 Horn control ................................................................................. 142 F How to fasten seat belts ............................................................. 60 F1-Trac ............................................................................................... 86 How to use the tires .................................................................. 237 Fastening the seat belts .............................................................. 44 Fault display .................................................................................. 125 I Fault displaying logic ................................................................ 125 Identification plates and labels ............................................... 22 Fault priority levels .................................................................... 126 If the vehicle is stored for long periods ............................ 243 FBP - Ferrari Brake Prefill ......................................................... 85 Ignition switch ..................................................................... 45, 101 Ferrari CODE system .................................................................. 17 Indication of "Auto" gearbox mode ................................... 135 Flashing the headlights .................................................... 46, 146 Indication of "Auto easy exit" gearbox mode ................ 135 Follow me home function ....................................................... 150 Indication of "Performance Start" mode activated ....... 136 Front Lift system (optional) ................................................... 174 Indication of AVH system activated .................................... 136 Fuel Consumption ........................................................................ 30 Indication of gearbox in "Parking" mode ........................ 135 Fuel filler flap and neck .......................................................... 102 Infotainment system .................................................................. 137 Fuel inertia switch .............................................................. 83, 213 Instruments and gauges .......................................................... 106 Fuel level gauge ........................................................................... 112 Internal rear view mirror ........................................................ 182 Fuses and relays ......................................................................... 203 254 Table of Contents

K Matt paintwork (optional) ...................................................... 240 MENU screen page .................................................................... 110 Key-on ............................................................................................. 101 Key codes ......................................................................................... 16 N Key lock .......................................................................................... 101 N (Neutral) request ........................................................... 51, 157 L O Leather upholstery ..................................................................... 242 Left TFT display ......................................................................... 108 OK button ..................................................................................... 108 Level checks .................................................................................. 230 Opening doors ............................................................................... 38 Lighting system ........................................................................... 146 Opening doors from the outside ........................................... 96 Light bulbs .................................................................................... 201 Opening the engine compartment lid .................................. 97 Light switch ................................................................................... 146 Opening the fuel filler flap .................................................... 102 List of left TFT display symbols and warning lights Opening the luggage compartment lid ................................ 98 on the instrument panel .................................................... 128 OPEN button .............................................................................. 188 LOCK/UNLOCK ....................................................................... 151 Overview of controls ................................................................... 39 Locking and opening the doors from the inside .... 38, 96 P Low-grip mode ................................................................. 141, 164 Luggage compartment lid ......................................................... 98 Parking lights ................................................................................ 147 Parking mode ............................................................................... 135 M Parking sensors (optional) ...................................................... 121 Maintenance of seat belts and pretensioners .......... 62, 239 Parking sensor failure ............................................................... 124 Maintenance schedule .............................................................. 228 Park Lock ....................................................................................... 172 Main engine specifications ........................................................ 29 Park Lock emergency release ................................................ 224 MAIN screen page ..................................................................... 108 Passenger-side power window ............................................. 104 Manettino ...................................................................................... 164 Passenger airbag deactivation .................................................. 76 Manettino driving mode control switch ........................... 140 Manettino status screen page ................................................ 118 PASSENGER AIRBAG OFF warning light ....................... 78 Passenger compartment accessories ................................... 188 8 Table of Contents 255

Passive safety ................................................................................... 56 Right TFT display ....................................................................... 136 Performance .................................................................................... 29 Roof panel controls .................................................................... 151 Performance Start ....................................................................... 173 Run Flat tires (optional) ............................................................ 33 Pocket-change compartments ............................................... 189 Power socket ................................................................................ 190 S Power steering system oil level ............................................. 234 Seats adjustments ............................................................... 41, 176 Power windows ........................................................................... 104 Seat belts ................................................................................... 44, 58 Pretensioners .................................................................................. 62 Seat heating system (Full Electric option) ...................... 180 Proper driving .............................................................................. 159 Sequential downshifting .......................................................... 156 PS button ....................................................................................... 173 Service .................................................................................................. 8 Push start ........................................................................................ 158 SETUP ............................................................................................ 108 R Shift Indicator Light .................................................................... 30 Side airbags ..................................................................................... 80 RACE mode ....................................................................... 141, 165 Side view mirrors ....................................................................... 183 Racing seat ..................................................................................... 181 Slow Down function .................................................................. 219 Rain sensor .................................................................................... 145 Space-saving spare wheel (optional) .................................. 210 Rain sensor failure ...................................................................... 145 Spare parts .......................................................................................... 8 Rear and side view mirrors ................................................... 182 Speedometer display ................................................................. 137 Rear fog lights ....................................................................... 47, 149 Speedometer screen page ....................................................... 137 Rear Parking Camera screen page (optional) ................. 138 Speed limit exceeded message .............................................. 120 Recommended Lubricants and Fluids ................................ 34 Speed limit setting ...................................................................... 120 Reconnecting the battery ........................................................ 215 SPORT 2 screen page ............................................................... 113 Replacing a fuse ......................................................................... 202 SPORT mode .................................................................... 141, 164 Replacing a wheel ....................................................................... 210 SPORT screen page ................................................................... 113 Replacing license plate light bulbs ..................................... 199 Stability and Traction Control ................................................. 85 Replacing remote control batteries ....................................... 19 Starting and driving the vehicle ................................... 48, 153 Replacing the brake pads and discs .................................... 222 Starting the engine ............................................................. 49, 154 Replacing the front and rear light bulbs ......................... 199 STATUS .......................................................................................... 108 256 Table of Contents

Steering wheel ..................................................................... 42, 182 Turn indicators and running lights failure ....................... 126 Stopping the vehicle .......................................................... 51, 157 Twilight sensor ............................................................................. 148 Stop and Go function ............................................................... 121 Sun visors ...................................................................................... 189 U Suspension damping button ....................................... 142, 168 Unfastening the seat belts .................................................. 44, 61 Suspension damping control ................................................ 163 UP, DOWN, LEFT, RIGHT buttons .................................. 108 T UP-shifting ............................................................................. 51, 156 UP-shifting due to overrevving ............................................ 156 Time display .................................................................................. 137 Updating .............................................................................................. 8 tires pressure ................................................................................... 31 UP shift paddle ............................................................................ 143 TIRES screen page .................................................................... 114 Tire puncture .................................................................................. 90 V Tire temperature and pressure VDA ................................................................................................. 108 monitoring system (TPMS) ............................................... 88 VDA screen page group ........................................................... 114 Toolkit ............................................................................................. 194 Vehicle Dynamic Assistance .................................................... 114 Tool bag ......................................................................................... 194 Vehicle event data ......................................................................... 12 Towing ............................................................................................. 212 Vehicle keys ..................................................................................... 16 TPMS ................................................................................................. 88 Vehicle status screen page ....................................................... 116 TPMS failure ................................................................................... 93 TPMS not active ............................................................................ 93 TPMS not calibrated ................................................................... 92 TPMS temporarily not active ................................................... 93 Transmission ratios ....................................................................... 29 Treadwear ......................................................................................... 32 TRIP ................................................................................................ 108 TRIP A and TRIP B screen pages ....................................... 119 Turning off the engine ...................................................... 51, 157 Turn indicators ............................................................................. 148 8 Table of Contents 257

W Warming up the engine .................................................... 50, 155 Warning: danger of ice message ........................................... 120 Warranty Book ........................................................................ 8, 228 Weights .............................................................................................. 28 Wheels and tires .......................................................................... 237 Wheel alignment check and adjustment ........................... 238 Wheel Replacement ..................................................................... 32 Wheel rims ....................................................................................... 31 While traveling ............................................................................. 159 Windshield and headlight washer fluid ............................ 236 Windshield washer ..................................................................... 144 Windshield washer/wiper lever ............................................ 143 258 Table of Contents

Equipment and options in Ferrari vehicle models may vary because of specific legal and market requirements. Ferrari reserves the right to make any modification to the vehicle models described in this manual, at any time, for either technical or commercial reasons without any notice. Contact the nearest Authorized Ferrari Dealer for any further information you may require. In the interests of efficiency and safety, as well as to preserve the value of the vehicle, we do not recommend modifying the equipment using non-approved parts.