Wildgame Innovations Cloak Pro™ 10 Lightsout™ Manual

Thursday, August 17, 2017

High Intensity Invisible IR Digital Scouting Camera User’s Manual Model # KP10B8-7

Includes Camera Unit 2 - Bungee Cords User Manual page 1

Features RESOLUTION MAX: 10 MP FLASH 36 pc High Intensity Invisible Infrared LED’s FLASH RANGE up to 65 feet SENSOR Passive Infrared Sensor (PIR) Motion and Heat SENSOR RANGE up to 60 feet IMAGE FORMAT JPEG - Digital Stills/ AVI-Digital Video MEMORY up to 32GB SD Card (not included and required) Class 4 and above recommended IMAGE RESOLUTION 10 MP POWER SUPPLY 8 AA batteries (not included and required) Alkaline recommended BATTERY LIFE Estimated up to 1 year or 30,000 photos HOUSING Weather resistant with rubber gaskets MOUNTING 2 Bungee cords - included page 2

Installing Batteries 1. Open the door at the bottom of the camera by unlatching the locking tab. 3. With the bottom of the camera to- wards you, Make sure to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative. 2. With the camera facing open, open the battery compartment cover by sliding the latch to the left. NOTE: Do not mix old and new batteries. Do not mix alkaline, standard (carbon- zinc) or rechargable (ni-cad, ni-mh, etc) batteries. page 3

4. Close battery compartment cover. To latch the cover simply pull the latch slightly to the left as you close 5. Load SD memory card (up to 32GB not included) into the SD card slot with the connectors facing up. the battery compartment cover. IMPORTANT: Make sure the camera is powered off before removing or installing an SD card. If you are using an SD card from other cameras, please make sure to format the SD card in your computer prior to use in your camera. New cards are ok to use straight from the package. page 4

Power On Test Mode 1. To turn the unit ON press and release the power button. 1. LCD Ready Mode: The camera will automatically enter Ready Mode if a button is not pressed for greater than 30 seconds. 2. LED Status Light: During the first 30 seconds of the LCD Ready Mode, the red light will illuminate when a POWER + - ENTER PIR event is triggered. After the LCD turns off, the red light will blink 2-3 seconds when photo is taken. After 2 minutes, all indicator lights will 2. Check the battery level icon to ensure the batteries just installed contain the proper turn off until a button is pressed. charge level. If so, you are ok to proceed with camera use. page 5

Power Save Setting Time 1. After 30 seconds without any buttons being pushed, the LCD will turn off 1. To change date and time, start by pressing and releasing the enter and camera enters into Power Save navigation button to set the hour. or Ready Mode. 2. The LCD screen can be awakened by pressing the Power button briefly. Note: The LCD will not “wake up” POWER + - ENTER when camera is writing to memory. 2. Press the + or - navigation button to go up or down in sequence. POWER + - ENTER POWER + - ENTER 3. When the hour is set, repeat steps 1 and 2 to set the minutes. page 6

Setting Date Photos 1. Press the enter navigation button after setting the minute to change the Date. 1. Press and release the enter navigation button to choose Photos. The number displayed is MM DD the number of photos on your SD card. This is not a programmable mode for the camera. POWER + - ENTER 2. Press the + or - navigation button to go up or down in sequence. MM POWER + - ENTER DD POWER + - ENTER 3. When the Month is set, repeat steps 1 and 2 to set the Day and Year. page 7

Image Delay 1. Press the enter navigation button while Image is selected. The highlighted option will be blinking. 1. Press the enter navigation button while Delay is selected. The highlighted option will be blinking. AM AM POWER + - ENTER POWER + - ENTER 2. Press the + or - navigation button to move to different options. 2. Press the + or - navigation button to move to different options. Press the enter navigation button Press the enter navigation button to save the setting. to save the setting. AM AM POWER + - ENTER POWER + - ENTER DELAY: The time before the camera is able to take another picture. page 8

Power Off Image Stamp 1. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until Pictures Display: the LCD turns off. POWER + - ENTER A B C D A- Time B- Date C- Moon Phase D- Photo Count page 9

Mounting Important 1. When mounting to a tree, first latch the 2 bungee cords through the mounting holes on the left or right TIPS: Recommended distance from target area is 25-30 feet for optimal imaging quality. To improve the quality of your images, try not to mount side of the camera. Then, stretch the unit facing the rising or the setting sun in order to the cords around the tree and latch avoid direct sunlight into the camera lens. the other ends of the bungee cords If mounting to a feeder unit or dusty environment, be sure to clean the camera lens cover, incandescent flash through the mounting holes on the cover, and the PIR sensor cover on a regular basis. opposite side of the camera. Periodically check the mounting of the camera to insure it is not loose. Make sure that you securely latch the door closed each and every time you use the unit, as the moisture seal will not be activated unless closed properly. Check batteries frequently to insure no corrosive build-up, as this may cause harm to the camera. page 10

Retrieving Images (SD Card Reader) Method 1: Remove SD card and use card F. If your computer does not automatically reader launch the AutoPlay window recognizing the A. First, remove the SD Card from the cam- Removable Disk (the SD Card), then you will era unit itself by pressing on it to where it need to go to the “Start Menu” at the bottom automatically ejects. left of your screen and select “Computer”. B. Next, insert the SD card into your SD The summary view will then be illustrated card reader. on the right hand side of the window where C. Once inserted into your computer it may by the “Devices with Removable Storage” automatically launch “AutoPlay”, a window will be listed. The computer will recognize recognizing a new Secure Digital Storage the reader as “Secure Digital Storage De- Device (the SD Card). vice”. Please select “Secure Digital Storage D. If so, it should list several options for Device” from this menu (or double click on the next steps (not limited to the following): the graphical icon). 1. Picture Options G. This will then direct you into the SD Card a. Import pictures file folder. Images are in the MEDIA folder. b. View pictures H. Once open, you will then see all of the c. Copy Disc photo files that are located on the SD Card. d. Transfer pictures Select each image individually to view. The 2. General Options default viewing browser for your computer a. Open folder to view files will then automatically launch. E. Select the method from the list provided I. Repeat for viewing all or other photos. that best suits your requirements. If the se- J. If you determine that you want to delete lection is made to “View pictures”, you can the image, select the image by placing your then view the images located on the SD Card cursor on it and clicking your mouse only and manipulate them as needed. once. Right click on your mouse and select delete. This will delete the image perma- nently, so be absolutely sure you want to do this before selecting delete. page 11

Format SD Card SDXC cards are not supported. Having trouble with your SD card? Try this. 1. Connect the SD card to your computer. If your computer has an SD card slot you can insert the SD card directly into the port. NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into standard SD card ports. If your computer does not have an SD card port built-in, you can use an external USB card reader that plugs into any USB port on your computer. 2. Click the Start or Windows menu and select Computer (Windows Vista/7) or My Computer (Windows XP). For Windows 8 users, type “computer” and click the Computer icon in the Apps search results. 3. Right-click the drive letter associated with your memory device, then select “Format” 4. Ensure FAT32 is selected under “File System” 5. Ensure ”Quick Format” is checked 6. Click “Start” page 12

Warranty DISCLAIMERS WGI Innovations, LTD is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY For the warranty to be in effect, visit our website and register your product at www.wildgameinnovations.com. Follow the onscreen directions to complete the process. WGI Innovations, LTD will replace all workmanship defects free of charge for ONE (1) YEAR after the date of purchase as long as your warranty is in effect. This warranty DOES NOT COVER damage, expense or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss. When returning product(s) for service you MUST obtain a Return Merchandise Authorization (RMA) number from WGI Innovations, LTD. Please include name, UPS address (No P.O. Box), telephone number, RMA number and a complete description of the problem on all enclosed correspondence. When possible, pack product carefully in original carton. Customers are responsible for any shipping cost to WGI Innovations™. WGI Innovations™ will pay the shipping cost of replacement product to the customer. We are not responsible for damage incurred in returning items for repair. For product service send to: WGI Innovations™ 602 Fountain Parkway Grand Prairie, TX 75050 (800) 847-8269 www.wildgameinnovations.com Thank you for your purchase! CUSTOMER SERVICE WGI Innovations, LTD. stands behind every product we manufacture for a one year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or need assistance with the operation or assembly of your product, we encourage you to call one of our customer service representatives and let us assist you with your WGI Innovations™ product. DISCLAIMER WGI Innovations, LTD reserves the right to make changes to product features, functionality and physical design at its sole discretion. As a result, such changes may not be reflected in this version of the manual. page 13

FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# KP10B8-7 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm- ful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. page 14

602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are trademarks of Wildgame Innovations, LLC.