Wildgame Innovations CRUSH™ Cell Cam™ Manual

Thursday, August 17, 2017
Download

Invisible Infrared Digital Cellular Scouting Camera User’s Manual Model # C8B5-7

Includes USB Cable 2 - Bungee Cords User Manual Flextime Player Camera Unit Antenna Software SIM card NOTE: Flextime Player Software is optional. Flextime files can be played by using most media players page 1

Features RESOLUTION MAX: 8 MP FLASH 60 High Intensity Invisible IR LED’s FLASH RANGE up to 70 feet SENSOR Passive Infrared Sensor (PIR) Motion and Heat SENSOR RANGE up to 60 feet IMAGE FORMAT JPEG - Digital Still / AVI - Digital Video MEMORY up to 32GB SD Card (not included and required) Class 4 and above recommended USB 5-PIN Mini USB style - included IMAGE RESOLUTION High (8MP) Medium (6MP) Low (4MP) POWER SUPPLY 4 D batteries (not included and required) Alkaline recommended AUXILIARY POWER External power port ONBOARD POWER Capacitor to retain Time and Settings HOUSING Weather resistant with rubber gaskets MOUNTING 2 Bungee cords - included CELLULAR TYPE 2G(GSM) and 3G(WCDMA), CDMA and CDMA2000 not supported SIM CARD Mini-SIM (2FF) required Cell Mode can be activated only when the camera is set in PIR mode/im- age. If the camera is set to Video or Flextime, the Cell mode will be disabled. Note: Battery life will vary depending on camera settings as well as environ- mental conditions. Camera settings such as shorter delay periods or even us- ing Flextime mode are examples of settings that can reduce overall battery life. Environmental conditions such as extreme cold can also influence battery life. page 2

Setup 1. With the camera facing up, open the battery compartment at the bottom of the camera by turning them to 3. Close battery compartment cover by turning them to the right. the left. 2. With the bottom of the camera towards you, load 2 D batteries with the positive ends towards you in 4. each chamber. Open the door at the bottom of the camera by unlatching the locking tabs. - - + + - - + + NOTE: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargable (ni-cad, ni-mh, etc.) batteries. page 3

5. To attach the antenna, place the bottom of the antenna into the screw hole at the top of the camera. Then 6. Load SD memory card (up to 32GB not included) into the SD card slot with the connectors facing down. turn the antenna clockwise until it is secure. Do not over tighten. IMPORTANT: Make sure the camera is powered off before removing or installing an SD card. If you are using an SD card from other cameras, please make sure to format the SD card in your computer prior to use in your camera. New cards are ok to use straight from the package. 7. Load Mini-SIM (2FF) card into the SIM card slot with the connectors facing down. page 4

Power On Test Mode 1. To turn the unit ON, press and release the power button. 1. LCD Ready Mode: The camera will automatically enter Ready Mode if a button is not pressed for greater than 30 seconds. The status lights UP R will illuminate for a total of 2 minutes. OK 2. PIR LED Status Light: During the DN L first 2 minutes of Ready Mode, the red light will illuminate when a PIR event is triggered. The red light will blink for 2-3 seconds when photo 2. Check the battery level icon to ensure the batteries just installed contain the proper charge level. is taken during this first 2 minutes. After 2 minutes all indicator lights will turn off until a button is If so, you are ok to proceed with pressed. camera use. UP R OK DN L Note: When Powered on or Woken up, the camera takes 5-10 seconds to check SIM card and/or Network settings. The buttons are locked during this period. page 5

Power Save Date/Time 1. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into 1. To change Date & Time, enter MENU and press the UP,DN,L or R buttons to navigate to the DATE & TIME icon Power Save or Ready Mode. and press OK. 2. 30 The LCD screen can be awakened by DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R pressing the Power button briefly. PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK Note: The LCD will not “wake up” when PLAY BACK VIEW ASSIST DN L camera is writing to memory. UP R 2. Press the UP or DN navigation button to go up or down in sequence. Press L or R to move to the next OK digit. TIME/D AT E 1_ _2 :_00_ AMPM DN L UP R 11 01 12 __/__/__ MONTH DAYY EAR OK BACK DN L 3. When the Time & Date are set, press OK to save and press OK again to go back to the MENU. TIME/D AT E UP 1__:_ 20 _0 AMPM R 11 01 _1 _2 __/__/ MONTH DAYY EAR OK BACK DN L page 6

Location Image Type:Still Save the location of the area the camera was installed. This is for your reference and is optional. If you do not wish to 1. To change Image Type, enter MENU and press the UP,DN,L or R buttons to navigate to the Image Type icon name your location skip to the next step. and press OK. 1. To change Location, enter MENU and press the UP,DN,L or R buttons to navigate to the LOCATION icon UP 30 DATE & TIME PIR SENSITIVITY LOCATION ACTIVE TIME IMAGE TYPE + FLEXTIME +™ TRIGGER DELAY R OK and press OK. PLAY BACK VIEW ASSIST BACK DN L 30 2. DATE & TIME LOCATION IMAGE TYPE TRIGGER UP + R Press the L, R button to select PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK STILL and press OK. Then select the DN PLAY BACK VIEW ASSIST BACK L Resolution and press OK. Select the Exposure and press OK. Then select 2. Press the UP or DN navigation button to go up or down in sequence. Press L or R to move to the next the aspect and press OK. IM AG E TY PE STILL VIDE O digit. UP R HI ME DL OW RESO LU TION HI ME DL OW EXP C ONTRO L OK LO CA TION REGULA R WIDE ANGLE BACK UP R _A _B ______ DN L OK 3. When the Image Type is set, press BACK DN L OK to save and press OK again to go 3. When the Location is set, press OK back to the MENU. to save and press OK again to go IM AG E TY PE STILL VIDE O back to the MENU. UP HI ME DL OW RESO LU TION R HI ME DL OW EXP C ONTRO L OK LO CA TION BACK UP R REGULA R WIDE ANGLE AB _C _D ____ __ DN L OK BACK DN L page 7

Image Type:Video Trigger 1. To change Image Type, enter MENU and press the UP,DN,L or R buttons to navigate to the Image Type icon This setting allows you to choose the mode in which the camera will be capturing images. and press OK. 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER 1. To change Trigger, enter MENU and press the UP,DN,L or R buttons to navigate to the Trigger icon and + UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK press OK. BACK PLAY BACK VIEW ASSIST DN L 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY 2. OK Press the L, R button to select PLAY BACK VIEW ASSIST BACK VIDEO and press OK. Then select DN L 2. the Resolution and press OK. Then Press the L, R button to select select the length and press OK. Trigger Mode. Then select the OK IM AG E TY PE to save. If PIR is selected press OK UP STILL VIDE O R again to go back to the MENU. HD REGULAR BACK OK TRIGGER 15 s 30 s1 m2 m VIDEO LENGT H R UP DN L PIR FlexTime BOTH OK BACK 3. DN L When the Image Type is set, press OK to save and press OK again to go TRIGGER: back to the MENU. PIR MODE: Takes a photo or video only when the PIR sensor is triggered. IM AG E TY PE UP STILL VIDE O R FLEXTIME (Time Lapse): Takes time lapse images at set intervals during the key movement periods of the day, depending on your Flextime settings. HD REGULA R BACK OK 15 s 30 s1 m2 m VIDEO LENGT H DN L BOTH: Both PIR and Flextime are active. page 8

PIR Sensitivity Image Type:Still 1. To change PIR Sensitivity, enter MENU and press the UP,DN,L or R buttons to navigate to the PIR 1. To change the Active Time, enter MENU and press the UP,DN,L or R buttons to navigate to the Active Sensitivity icon and press OK. Time icon and press OK. 30 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER DATE & TIME LOCATION IMAGE TYPE TRIGGER + + UP R UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK OK BACK BACK PLAY BACK VIEW ASSIST PLAY BACK VIEW ASSIST DN L DN L 2. Press the L, R button to select the sensitivity and press OK to save. Then press OK again to go back to 2. Press the L, R button to select the active time and press OK to save. Then press OK again to go back to the MENU. the MENU. PIR SENSITIVIT Y AC TIVE T IM E UP R R UP HI ME D LO W 24 H R DA Y NIGH T OK OK BACK BACK DN L DN L PIR ACTIVE: PIR SENSE: 24 HR: The PIR can be active at all times. HI: The PIR detects the smallest movement. DAY: The PIR can be active in daylight hours MED: (Default) The PIR detects most only. common size movements. NIGHT: The PIR can be active in nighttime LOW: The PIR detects only larger hours only. movements. page 9

FLEXTIME selected Flextime period: Camera is inactive before and after Flextime periods. Flextime is active twice a day. 1. 15 min before Sunrise P1 15 MINUTES 15 MINUTES BEFORE AFTER to 1 hour after Sunrise. SUNRISE FLEX FLEX SUNSET INACTIVE TIME TIME INACTIVE 2. 1 hour before Sunset to 15 min after Sunset 1 HOUR INACTIVE 1 HOUR AFTER BEFORE SUNRISE SUNSET Camera is in PIR mode before and after Flextime periods. Flextime is active twice a day. Flextime period: P2 1. 15 min before Sunrise to 1 hour after Sunrise. PIR FLEX TIME FLEX TIME PIR 2. 1 hour before Sunset PIR to 15 min after Sunset Flextime period: Camera is in PIR mode before and after Flextime periods. Flextime is active during daytime. 1. 15 min before Sunrise to 15 min after Sunset PIR PIR INTERVAL FLEXTIME BOTH selected Flextime + PIR period: Camera is inactive before and after Flextime + PIR periods. Flextime + PIR is active twice a day. 1. 15 min before Sunrise P1 15 MINUTES 15 MINUTES BEFORE AFTER to 1 hour after Sunrise. SUNRISE FLEX FLEX SUNSET INACTIVE TIME TIME INACTIVE 2. 1 hour before Sunset to 15 min after Sunset PIR 1 HOUR INACTIVE 1 HOUR PIR AFTER BEFORE SUNRISE SUNSET Camera is in PIR mode before and after Flextime + PIR periods. Flextime + PIR is active twice a day. Flextime + PIR period: P2 1. 15 min before Sunrise to 1 hour after Sunrise. PIR FLEX TIME FLEX TIME PIR 2. 1 hour before Sunset PIR PIR PIR to 15 min after Sunset Flextime + PIR period: Camera is in PIR mode before and after Flextime + PIR periods. Flextime + PIR is active during daytime. 1. 15 min before Sunrise to 15 min after Sunset PIR PIR INTERVAL FLEXTIME & PIR page 10

Flextime +™ PIR Delay 1. To change Flextime™, enter MENU and press the UP,DN,L or R buttons to navigate 1. To change the Delay, enter MENU and press the UP,DN,L or R buttons to navigate to the PIR Delay icon and to the Flextime™ icon and press OK. press OK. 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER 30 + UP R DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY BACK OK PLAY BACK VIEW ASSIST DN L BACK PLAY BACK VIEW ASSIST DN L 2. Press the L, R button to select the mode and press OK to save. Then press OK again to go back to the Flextime™ Display Options. (See chart on pg 10 for mode descriptions) 2. Press the L, R button to select the time between pictures in PIR mode and press OK to save. Then press UP R OK again to go back to the MENU. P1 P2 Interval OK DELA Y Flex Time BOTH BACK UP 15 s 30 s1 mi n R DN L 2min 5min 10min OK BACK 3. Press the L, R button to select the mode and DN L press OK to save. Then press OK again to go back to the Flextime™ Display Options. (See chart on pg 10 for mode descriptions) DELA Y UP 1min 2min 5min 10min R 15min 20min 25min 30min OK Flex Time BOTH BACK DN L NOTE: Camera needs at least 48 hours in the field to acclimate to the environment for Flextime to function properly. page 11

Playback: Stills Playback: Videos 1. To view your images, enter MENU and press the UP,DN,L or R buttons to navigate to the Playback icon and press OK. 1. To view your videos, enter MENU and press the UP,DN,L or R buttons to navigate to the Playback icon and press OK. 30 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R + UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK OK BACK BACK PLAY BACK VIEW ASSIST PLAY BACK VIEW ASSIST DN L DN L 2. Press the UP,DN,L or R button navigate through media. To view a image press OK 2. Press the UP,DN,L or R button navigate through media. To view a video press OK on the desired video. on the desired image. UP R UP R BACK BACK OK OK DN L DN L 3. ZOOM: Press L or R then select the Zoom In button. Select to scroll with the UP, DN, L, or R while zoomed in. Select Back 3. PLAY: Press L or R then select the Play button. Select Pause to freeze the playback. Press Back to return to Playback to return to normal size. Press Back again menu. to return to Playback menu. DELETE: Press L or R then select the DELETE: Press L or R then select the Delete button to delete the selected video. Delete button to delete the selected NOTE: Once deleted the file cannot be image. recovered. UP R UP R OK OK DELETE ZOOM ZOOM BACK IN OU T DELETE BACK DN L DN L page 12

View Assist Cellular MMS 1. To use View Assist, enter MENU and press the UP,DN,L or R buttons to 1. To use Cellular MMS, enter MENU and press the UP,DN,L or R buttons to navigate to the SIM 2/3G icon and press OK. navigate to the View Assist icon and press OK. 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R 30 DATE & TIME LOCATION IMAGE TYPE TRIGGER PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY OK + UP R BACK PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY PLAY BACK VIEW ASSIST OK DN L BACK 2. PLAY BACK VIEW ASSIST Press the L, R button to select the MMS- DN L YES and press OK. Then press OK again to 2. Once in View Assist, the camera will show a live view of the lens. Adjust the camera locations to your liking go to the MMS Settings. UP R and then press OK to return to the MENU. OK DN L 3. UP R Press OK to enter up to 3 cell numbers. BACK OK Press the UP or DN navigation button to DN L go up or down in sequence. Press L or R to move to the next digit. Press OK when finished. Press X to clear the number. Press SAVE to save the number then Press BACK when finished. Continue to Send Settings UP R 55 5 OK DN L page 13

Cellular Email Send Settings 1. To use Cellular Email, enter MENU and press the UP,DN,L or R buttons to navigate to the SIM 2/3G icon and press OK. 1. After setting the cell numbers and/ or email addresses press the Up,DN to navigate to the Send Settings button. 30 Press OK. DATE & TIME LOCATION IMAGE TYPE TRIGGER + UP R PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY UP R OK BACK PLAY BACK VIEW ASSIST OK DN L 2. DN L Press the L, R button to select the Email- 2. YES and press OK. Then press OK again to To send an image ever time the camera go to the Email Settings. takes a picture go to Every Event and press Save then Back. UP R SEND SET TING S EVERY EVEN T SCHEDULE TIME UP R OK OK DN L SAVE BACK DN L 3. Press OK to enter up to 3 email addresses. Press the UP or DN navigation button to go up or down in sequence. Press L or R 3. To send multiple images at up to 3 scheduled times go to Schedule Time and to move to the next digit. Press OK when press OK. Press OK again to set the time finished. Press SAVE to save the email to send. Press the UP or DN navigation then Press BACK when finished. Press button to go up or down in sequence. Press CLEAR to clear the email. Continue to L or R to move to the next digit. Press OK Send Settings when finished. Press Save then Back. UP R UP R a OK OK DN L DN L page 14

Tips Power Off - Make sure there is cellular signal where the camera is being setup. 1. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until the LCD - Make sure the SIM card is activated before use. turns off. Camera will not power off if transmitting and/or writing an - Cellular settings only work on GSM and image to memory. WCDMA networks. - Weather and environment may effect signal strength. UP R - The camera will stop transmitting OK image when the battery is low. DN L page 15

Image Stamp Power Port Pictures Display: 1. WGI Cameras come standard with an external power port. You must open the weather resistant cover and use a Wildgame Innovations 6 Volt camera battery accessory. 087°F 08:15PM 11-12-2011 T08 0200 A B C D E F A- Temperature B- Time C- Date Adjusting Screws D- Moon Phase E- Location F- Photo Count The two screws can be fastened into the screw nuts on top of the battery tube for adjusting the camera orientation on the tree. page 16

Mounting 1. When mounting to a tree, first latch the 2 bungee cords through the mounting holes on the left or right Adjustable sides to fit almost any size tree. side of the camera. Then, stretch the cords around the tree and latch the other ends of the bungee cords through the mounting holes on the opposite side of the camera. page 17

Important Once you connect the camera to your computer via the USB cable/ports, the camera will then draw power from the computer. When completing the viewing, transferring, copying or deletion of images, please make sure that you DISCONNECT THE USB CABLE FROM BOTH THE CAMERA AND THE COMPUTER, as you will not be able to power the camera OFF until you do so. The directions as contained herein assume that you are using a Microsoft operating system and not Linux or a Mac-based operating system. Even said, there may be slight variations in your process based on the specific version of the operation system that you are using as well as the predefined user preference for each computer. The below listed steps are to serve as a guideline and may have to be slightly modified based on the specific operating system and preference as on your personal computer. TIPS: Recommended distance from target area is 25-30 feet for optimal imaging quality. To improve the quality of your images, try not to mount the unit facing the rising or the setting sun in order to avoid direct sunlight into the camera lens. If mounting to a feeder unit or dusty environment, be sure to clean the camera lens cover, incandescent flash cover, and the PIR sensor cover on a regular basis. Periodically check the mounting of the camera to insure it is not loose. Make sure that you securely latch the door closed each and every time you use the unit, as the moisture seal will not be activated unless closed properly. Check batteries frequently to insure no corrosive build-up, as this may cause harm to the camera. page 18

Retrieving Images (SD Card in Camera) Method 1: Leave SD card in camera Please select Removable Disk from this A. First, make sure that the camera is pow- menu (or double click on the graphical icon). ered OFF. Next, plug the USB cable into the F. This will then direct you into the SD Card camera and then into the USB port on your file folder. Images are in the MEDIA folder computer. Once this is complete (in this or- while Flextime files are in the FLEX folder. der only), then power the camera ON. G. Once open, you will then see all of the B. Once complete, your computer may au- photo files that are located on the SD Card. tomatically launch “AutoPlay”, a window Select each image individually to view. The recognizing a new Removable disk (the default viewing browser for your computer camera). will then automatically launch. C. If so, it should give you three selections: H. Repeat for viewing all or other photos. 1. Import pictures I. If you determine that you want to delete 2. View pictures the image, select the image by placing your 3. Open folder to view files cursor on it and clicking your mouse only D. Select the method from the list provided once. Right click on your mouse and select that best suits your requirements. Once a delete. This will delete the image perma- selection is made, you can then view the im- nently, so be absolutely sure you want to do ages located on the SD Card and manipulate this before selecting delete. them as needed. E. If your computer does not automatically TIP: The software drivers necessary to launch the AutoPlay window recognizing the use and view the camera are automatically Removable Disk (the camera), then you will downloaded to the computer when you con- need to go to the “Start Menu” at the bottom nect your camera to the computer via the left of your screen and select “Computer”. included USB cable. The summary view will then be illustrated on the right hand side of the window where the “Devices with Removable Storage” will be listed. The computer will recognize the camera as Removable Disk. page 19

Retrieving Images (SD Card Reader) Method 2: Remove SD card and use card left of your screen and select “Computer”. reader The summary view will then be illustrated A. First, remove the SD Card from the cam- on the right hand side of the window where era unit itself by pressing on it to where it by the “Devices with Removable Storage” automatically ejects. will be listed. The computer will recognize B. Next, insert the SD card into your SD the reader as “Secure Digital Storage De- card reader. vice”. Please select “Secure Digital Storage C. Once inserted into your computer it may Device” from this menu (or double click on automatically launch “AutoPlay”, a window the graphical icon). recognizing a new Secure Digital Storage G. This will then direct you into the SD Card Device (the SD Card). file folder. Images are in the MEDIA folder D. If so, it should list several options for while Flextime files are in the FLEX folder. the next steps (not limited to the following): H. Once open, you will then see all of the 1. Picture Options photo files that are located on the SD Card. a. Import pictures Select each image individually to view. The b. View pictures default viewing browser for your computer c. Copy Disc will then automatically launch. d. Transfer pictures I. Repeat for viewing all or other photos. 2. General Options J. If you determine that you want to delete a. Open folder to view files the image, select the image by placing your E. Select the method from the list provided cursor on it and clicking your mouse only that best suits your requirements. If the se- once. Right click on your mouse and select lection is made to “View pictures”, you can delete. This will delete the image perma- then view the images located on the SD Card nently, so be absolutely sure you want to do and manipulate them as needed. this before selecting delete. F. If your computer does not automatically launch the AutoPlay window recognizing the Removable Disk (the SD Card), then you will need to go to the “Start Menu” at the bottom page 20

Format SD Card SDXC cards are not supported. Having trouble with your SD card? Try this. 1. Connect the SD card to your computer. If your computer has an SD card slot you can insert the SD card directly into the port. NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into standard SD card ports. If your computer does not have an SD card port built-in, you can use an external USB card reader that plugs into any USB port on your computer. 2. Click the Start or Windows menu and select Computer (Windows Vista/7) or My Computer (Windows XP). For Windows 8 users, type “computer” and click the Computer icon in the Apps search results. 3. Right-click the drive letter associated with your memory device, then select “Format” 4. Ensure FAT32 is selected under “File System” 5. Ensure ”Quick Format” is checked 6. Click “Start” page 21

FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# C8B5-7 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. page 22

Warranty DISCLAIMERS WGI Innovations, LTD is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY For the warranty to be in effect, visit our website and register your product at www.wildgameinnovations. com. Follow the onscreen directions to complete the process. WGI Innovations, LTD will replace all workmanship defects free of charge for ONE (1) YEAR after the date of purchase as long as your warranty is in effect. This warranty DOES NOT COVER damage, expense or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss. When returning product(s) for service you MUST obtain a Return Merchandise Authorization (RMA) number from WGI Innovations, LTD. Please include name, UPS address (No P.O. Box), telephone number, RMA number and a complete description of the problem on all enclosed correspondence. When possible, pack product carefully in original carton. Customers are responsible for any shipping cost to WGI Innovations™. WGI Innovations™ will pay the shipping cost of replacement product to the customer. We are not responsible for damage incurred in returning items for repair. For product service send to: WGI Innovations™ 602 Fountain Parkway Grand Prairie, TX 75050 (800) 847-8269 www.wildgameinnovations.com Thank you for your purchase! CUSTOMER SERVICE WGI Innovations, LTD. stands behind every product we manufacture for a one year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or need assistance with the operation or assembly of your product, we encourage you to call one of our customer service representatives and let us assist you with your WGI Innovations™ product. DISCLAIMER WGI Innovations, LTD reserves the right to make changes to product features, functionality and physical design at its sole discretion. As a result, such changes may not be reflected in this version of the manual. page 23

page 24

Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. 602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are trademarks of Wildgame Innovations, LLC. “Flextime” is a trademark of WGI Innovations, LTD.