Wildgame Innovations CRUSH™ X20 Lightsout™ Manual

Thursday, August 17, 2017
Download

Invisible IR Digital Scouting Camera User’s Manual Model # L20B20-7

Includes Camera Unit User Manual Flextime Player Adjustable Strap Software NOTE: Flextime Player Software is optional. Flextime files can be played by using most media players page 1

Features RESOLUTION MAX: 20 MP FLASH 56 pc High Intensity Invisible IR LED’s FLASH RANGE up to 100 feet SENSOR Passive Infrared Sensor (PIR) Motion and Heat SENSOR RANGE up to 60 feet IMAGE FORMAT JPEG - Digital Stills/ AVI-Digital Video MEMORY up to 32GB SD Card (not included and required) Class 6 and above recommended USB 5-PIN Micro USB style - (not included) IMAGE RESOLUTION High (20 MP) Medium (10 MP) Low (5 MP) POWER SUPPLY 8 AA batteries (not included and required) Alkaline recommended BATTERY LIFE Estimated up to 1 Year or 30,000 photos ONBOARD POWER Built in capacitor to retain Date and Time HOUSING Weather resistant with rubber gaskets MOUNTING Adjustable Strap - included Note: Battery life will vary depending on camera settings as well as environmental conditions. Camera settings such as shorter delay periods or even using Flextime mode are examples of settings that can reduce overall battery life. Environmental conditions such as extreme cold can also influence battery life. page 2

Installing Batteries 1. Open the door on the right of the camera and PULL the tab towards you. 3. Push the battery latch up to unlock. At the same time grab the battery compartment out. With the camera facing up, open the compartment door. 2. Open the door on the bottom of the camera and PULL the tab towards you. With the camera facing up, open the compartment door. page 3

4. Make sure to insert the AA-cell batteries based on the direction labeled on the inside of each com- 5. Load SD memory card (up to 32GB not included) into the SD CARD slot with the connectors facing down. partment. Match minus “-” sign with the marked negative on the battery and the plus “+” sign with the marked plus sign on the battery. IMPORTANT: + _ _ + Make sure the camera is powered off before removing or installing an SD card. If you are using an SD card from other cam- eras, please make sure to format the SD card in _ + + _ your computer prior to use in your camera. New cards are ok to use straight from the package. + _ _ + page 4

Power On Test Mode 1. To turn the unit ON press and release the power button. 1. LCD Ready Mode: The camera will automatically enter Ready Mode if a button is not pressed for greater than 30 seconds. The status lights will illuminate for a total of 2 minutes. 2. PIR LED Status Light: During the first 2 minutes of Ready Mode, the red light will illuminate when a PIR event is triggered. The red light will blink for 2-3 seconds when photo is taken during this first 2 minutes. 2. Check the battery level icon to ensure the batteries just installed contain the proper charge level. If so, you are After 2 minutes all indicator lights will turn off until a button is pressed. ok to proceed with camera use. TIME / DATE 00:00 PM 00/00/00 LOCATION LOC1 IMAGE TYPE STILL - WIDE EXPOSURE LOW TRIGGER BOTH PIC RESOLUTION HIGH VID RESOLUTION REGULAR PIR SENSITIVITY MED ACTIVE TIME 24 HOURS FLEXTIME OFF DELAY 15S PICTURES TAKEN 0000 MENU PICTURES REMAINING 0000 page 5

Power Save Date/Time 1. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save 1. To change Date & Time, enter MENU and press the UP,DN,L or R buttons to navigate to the DATE & or Ready Mode. TIME icon and press ENTER. 30 2. DATE & TIME LOCATION IMAGE TYPE TRIGGER The LCD screen can be awakened by + ENTER pressing the Power button briefly. PIR SENSITIVITY ACTIVE TIME FLEXTIME +™ DELAY RESET BACK Note: The LCD will not “wake up” PLAY BACK VIEW ASSIST when camera is writing to memory. TIME / DATE LOCATION IMAGE TYPE EXPOSURE TRIGGER 00:00 PM 00/00/00 LOC1 STILL - WIDE LOW BOTH 2. Press the UP or DN navigation button to go up or down in sequence. Press L or R to move to the next digit. PIC RESOLUTION HIGH VID RESOLUTION REGULAR PIR SENSITIVITY MED ACTIVE TIME 24 HOURS FLEXTIME OFF DELAY 15S PICTURES TAKEN 0000 MENU PICTURES REMAINING 0000 ENTER RESET ENTER RESET 3. When the Time & Date are set, press ENTER to save and press ENTER again to go back to the MENU. ENTER RESET page 6

Location Image Type: Still Save the location of the area the camera was installed. This is for your reference and is optional. If you do not wish to name your 1. To change Image Type, enter MENU and press the UP,DN,L or R buttons to navigate to the Image location skip to the next step. Type icon and press ENTER. 1. To change Location, enter MENU and press the UP,DN,L or R buttons to navigate to the LOCATION icon ENTER and press ENTER. RESET 2. ENTER Press the L, R button to select RESET STILL and press ENTER. Then select the Resolution and press ENTER. Select the Exposure and 2. Press the UP or DN navigation button to go up or down in sequence. Press L or R to move to press ENTER. Then select the aspect and press ENTER. the next digit. ENTER ENTER RESET RESET 3. When the Location is set, press ENTER to save and press ENTER 3. When the Image Type is set, press ENTER to save and press ENTER again to go back to the MENU. again to go back to the MENU. ENTER ENTER RESET RESET page 7

Image Type: Video Trigger 1. To change Image Type, enter MENU and press the UP,DN,L or This setting allows you to choose the mode in which the camera will be capturing images. R buttons to navigate to the Image Type icon and press ENTER. 1. To change Trigger, enter MENU and press the UP,DN,L or R buttons to navigate to the Trigger ENTER icon and press ENTER. RESET ENTER RESET 2. Press the L, R button to select VIDEO and press ENTER. Then select the Resolution and press 2. Press the L, R button to select Trigger Mode. Then select the ENTER to save. If PIR is selected ENTER. Then select the length press ENTER again to go back to and press ENTER. the MENU. If FlexTime or Both is selected you will be redirected to ENTER the Flextime Menu (see page 11). RESET ENTER 3. When the Image Type is set, RESET press ENTER to save and press ENTER again to go back to the TRIGGER: MENU. PIR MODE: Takes a photo only when the PIR sensor is triggered. ENTER FLEXTIME(Time Lapse): Takes time lapse images at set intervals during the key movement RESET periods of the day, depending on your Flextime settings. page 8 BOTH: Both PIR and Flextime are active.

PIR Sensitivity Active Time 1. To change PIR Sensitivity, enter MENU and press the UP,DN,L or R buttons to navigate to the PIR 1. To change the Active Time, enter MENU and press the UP,DN,L or R buttons to navigate to the Active Sensitivity icon and press ENTER. Time icon and press ENTER. ENTER ENTER RESET RESET 2. Press the L, R button to select the sensitivity and press ENTER to save. Then press ENTER again 2. Press the L, R button to select the active time and press ENTER to go back to the MENU. to save. Then press ENTER again to go back to the MENU. ENTER ENTER RESET RESET PIR SENSE: HI: The PIR detects the smallest movement. PIR ACTIVE: MED: (Default) The PIR detects most common 24 HR: The PIR can be active at all times. size movements. DAY: The PIR can be active in daylight hours LO: The PIR detects only larger movements. only. NIGHT: The PIR can be active in nighttime hours only. page 9

Flextime +™ 30 MINUTES 30 MINUTES BEFORE AFTER SUNRISE SUNSET DUSK/DAWN FLEXTIME FLEXTIME INACTIVE INACTIVE INACTIVE 2 HOUR 2 HOUR AFTER BEFORE SUNRISE SUNSET 30 MINUTES 30 MINUTES BEFORE AFTER SUNRISE SUNSET ALL DAY FLEXTIME INACTIVE INACTIVE Both 30 MINUTES BEFORE SUNRISE 30 MINUTES AFTER SUNSET DUSK/DAWN PIR FLEXTIME FLEXTIME PIR PIR PIR PIR 2 HOUR 2 HOUR AFTER BEFORE SUNRISE SUNSET 30 MINUTES 30 MINUTES BEFORE AFTER SUNRISE SUNSET ALL DAY PIR PIR FLEXTIME & PIR page 10

Flextime +™ Delay 1. To change Flextime™, enter MENU and press the UP,DN,L or R buttons to navigate to the Flextime™ icon 1. To change the Delay, enter MENU and press the UP,DN,L or R buttons to navigate to the Delay and press ENTER. icon and press ENTER. ENTER ENTER RESET RESET 2. Press the L, R button to select the mode and press ENTER to save. Then press ENTER again to go back to the MENU. (See chart on pg 10 for mode descriptions) 2. Press the L, R button to select the time between pictures in PIR mode and press ENTER to save. Then press ENTER again to go ENTER back to the MENU. RESET ENTER 3. Press the L, R button to select the RESET time between images and press ENTER to save. Then press ENTER again to go back to the MENU. ENTER RESET NOTE: Camera needs at least 48 hours in the field to acclimate to the environment for Flextime to function properly. page 11

Playback: Stills Playback: Videos 1. To view your images, enter MENU and press the UP,DN,L or R buttons to navigate to the Playback icon and press 1. To view your videos, enter MENU and press the UP,DN,L or R buttons to navigate to the Playback icon and press ENTER. ENTER. ENTER ENTER RESET RESET 2. Press the UP,DN,L or R button navigate through media. To view a image press ENTER on the desired image. 2. Press the UP,DN,L or R button navigate through media. To view a video press ENTER on the desired video. ENTER ENTER RESET RESET 3. ZOOM: Press L or R then select the Zoom In button. Select to scroll with the UP, DN, L, or R while zoomed in. 3. PLAY: Press L or R then select the Play button. Select Pause to freeze the playback. Press Back to return to Select Back to return to normal size. Playback menu. Press Back again to return to Playback DELETE: Press L or R then select the menu. Delete button to delete the selected DELETE: Press L or R then select the video. NOTE: Once deleted the file Delete button to delete the selected cannot be recovered. image. ENTER ENTER RESET RESET page 12

View Assist Power Off 1. To use View Assist, enter MENU and press the UP,DN,L or R buttons to navigate to the View 1. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until Assist icon and press OK. the LCD turns off. ENTER RESET 2. Once in View Assist, the camera will show a live view of the lens. Adjust the camera locations to your liking and then press ENTER to return to the MENU. Reset ENTER Reset button located next to the RESET navigation buttons. Push button to reset settings back to factory settings. ENTER RESET page 13

Image Stamp Mounting Pictures Display: 1. When mounting to a tree, first remove the clip from one end of the strap so you can slide the strap through the slots located on the back of the camera. Once the camera is attached place the clip back on to the strap. Then, wrap the strap around the tree and clip the two ends together. Pull the excess material so that the camera is straped tightly to the tree. 087°F 08:15PM 11-12-2011 T08 0200 A B C D E F A- Temperature B- Time C- Date D- Moon Phase E- Location F- Photo Count page 14

Important Once you connect the camera to your computer via the USB cable/ports, the camera will then draw power from the computer. When completing the viewing, transferring, copying or deletion of images, please make sure that you DISCONNECT THE USB CABLE FROM BOTH THE CAMERA AND THE COMPUTER, as you will not be able to power the camera OFF until you do so. The directions as contained herein assume that you are using a Microsoft operating system and not Linux or a Mac-based operating system. Even said, there may be slight variations in your process based on the specific version of the operation system that you are using as well as the predefined user preference for each computer. The below listed steps are to serve as a guideline and may have to be slightly modified based on the specific operating system and preference as on your personal computer. TIPS: Recommended distance from target area is 25-30 feet for optimal imaging quality. To improve the quality of your images, try not to mount the unit facing the rising or the setting sun in order to avoid direct sunlight into the camera lens. If mounting to a feeder unit or dusty environment, be sure to clean the camera lens cover, incandescent flash cover, and the PIR sensor cover on a regular basis. Periodically check the mounting of the camera to insure it is not loose. Make sure that you securely latch the door closed each and every time you use the unit, as the moisture seal will not be activated unless closed properly. Check batteries frequently to insure no corrosive build-up, as this may cause harm to the camera. page 15

Retrieving Images (SD Card in Camera) Method 1: Leave SD card in camera while Flextime files are in the FLEX folder. A. First, make sure that the camera is G. Once open, you will then see all of the powered OFF. Next, plug the USB cable into photo files that are located on the SD Card. the camera and then into the USB port on Select each image individually to view. The your computer. Once this is complete (in this default viewing browser for your computer order only), then power the camera ON. will then automatically launch. B. Once complete, your computer may H. Repeat for viewing all or other photos. automatically launch “AutoPlay”, a window I. If you determine that you want to delete recognizing a new Removable disk (the the image, select the image by placing camera). your cursor on it and clicking your mouse C. If so, it should give you three selections: only once. Right click on your mouse and 1. Import pictures select delete. This will delete the image 2. View pictures permanently, so be absolutely sure you 3. Open folder to view files want to do this before selecting delete. D. Select the method from the list provided that best suits your requirements. Once TIP: The software drivers necessary to a selection is made, you can then view use and view the camera are automatically the images located on the SD Card and downloaded to the computer when you manipulate them as needed. connect your camera to the computer via E. If your computer does not automatically the included USB cable. launch the AutoPlay window recognizing the Removable Disk (the camera), then you will need to go to the “Start Menu” at the bottom left of your screen and select “Computer”. The summary view will then be illustrated on the right hand side of the window where the “Devices with Removable Storage” will be listed. The computer will recognize the camera as Removable Disk. Please select Removable Disk from this menu (or double click on the graphical icon). F. This will then direct you into the SD Card file folder. Images are in the MEDIA folder page 16

Retrieving Images (SD Card Reader) Method 2: Remove SD card and use then be illustrated on the right hand side card reader of the window where by the “Devices with A. First, remove the SD Card from the Removable Storage” will be listed. The camera unit itself by pressing on it to computer will recognize the reader as where it automatically ejects. “Secure Digital Storage Device”. Please B. Next, insert the SD card into your select “Secure Digital Storage Device” from SD card reader. this menu (or double click on the graphical C. Once inserted into your computer icon). it may automatically launch “AutoPlay”, G. This will then direct you into the SD Card a window recognizing a new Secure file folder. Images are in the MEDIA folder Digital Storage Device (the SD Card). while Flextime files are in the FLEX folder. D. If so, it should list several options H. Once open, you will then see all of the for the next steps (not limited to the photo files that are located on the SD Card. following): Select each image individually to view. The 1. Picture Options default viewing browser for your computer a. Import pictures will then automatically launch. b. View pictures I. Repeat for viewing all or other photos. c. Copy Disc J. If you determine that you want to delete d. Transfer pictures the image, select the image by placing 2. General Options your cursor on it and clicking your mouse a. Open folder to view files only once. Right click on your mouse and E. Select the method from the select delete. This will delete the image list provided that best suits your permanently, so be absolutely sure you requirements. If the selection is made want to do this before selecting delete. to “View pictures”, you can then view the images located on the SD Card and manipulate them as needed. F. If your computer does not automatically launch the AutoPlay window recognizing the Removable Disk (the SD Card), then you will need to go to the “Start Menu” at the bottom left of your screen and select “Computer”. The summary view will page 17

Format SD Card Having trouble with your SD card? Try this. 1. Connect the SD card to your computer. If your computer has an SD card slot you can insert the SD card directly into the port. NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into standard SD card ports. If your computer does not have an SD card port built-in, you can use an external USB card reader that plugs into any USB port on your computer. 2. Click the Start or Windows menu and select Computer (Windows Vista/7) or My Computer (Windows XP). For Windows 8 users, type “computer” and click the Computer icon in the Apps search results. 3. Right-click the drive letter associated with your memory device, then select “Format”  4. Ensure FAT32 is selected under “File System” (For SDXC cards, use EXFAT) 5. Ensure ”Quick Format" is checked 6. Click “Start” page 18

Warranty DISCLAIMERS WGI Innovations, LTD is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY For the warranty to be in effect, visit our website and register your product at www.wildgameinnovations. com. Follow the onscreen directions to complete the process. WGI Innovations, LTD will replace all workmanship defects free of charge for ONE (1) YEAR after the date of purchase as long as your warranty is in effect. This warranty DOES NOT COVER damage, expense or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss. When returning product(s) for service you MUST obtain a Return Merchandise Authorization (RMA) number from WGI Innovations, LTD. Please include name, UPS address (No P.O. Box), telephone number, RMA number and a complete description of the problem on all enclosed correspondence. When possible, pack product carefully in original carton. Customers are responsible for any shipping cost to WGI Innovations™. WGI Innovations™ will pay the shipping cost of replacement product to the customer. We are not responsible for damage incurred in returning items for repair. For product service send to: WGI Innovations™ 602 Fountain Parkway Grand Prairie, TX 75050 (800) 847-8269 www.wildgameinnovations.com Thank you for your purchase! CUSTOMER SERVICE WGI Innovations, LTD. stands behind every product we manufacture for a one year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or need assistance with the operation or assembly of your product, we encourage you to call one of our customer service representatives and let us assist you with your WGI Innovations™ product. DISCLAIMER WGI Innovations, LTD reserves the right to make changes to product features, functionality and physical design at its sole discretion. As a result, such changes may not be reflected in this version of the manual. page 19

FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# L20b20-7 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. page 20

602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are trademarks of Wildgame Innovations, LLC. “Flextime” is a trademark of WGI Innovations, LTD.